Smart Radar Sanitary Ferrule Mtg. Sensors

Transcription

1 Smart adar Sanitary Ferrule Mtg. Sensors FETUES Food Grade Teflon ntenna c/w Ferrule Mtg. Base Programmable (recommend) and Simple push-button calibration Output 4-20 m / 20-4m (Isolated on 4 Wire Model s only ) Optional S22 O S485 communications with calibration, diagnostics & data logging software PL compatible (Modbus TU) Three or four Wire Operation PPLITIONS Food and Beverages Water Pharmaceutical MEHNIL TLOGUE # - On the Web return to Home Page & efer to catalogue Number Structure for Ordering information. In Product Documentation refer to page 4. TEHNIL SPEIFITIONS 017 * - 17 ft. * - 5 m 0 * - ft. * - 10 m 050 * - 50 ft. * - 15 m 100 * ft. * - 0 m mm 2.0 NPT mm 2.0 NPT mm 2.0 NPT mm 2.0 NPT Note - * Minimum ange starts at the lower tip of the antenna for high dielectric materials (water). For low dielectric materials allow for longer Minimum ange Standard Unit - luminum Housing - Teflon ntenna Sanitary Ferrule - 2 Teflon - PTFE onduit Entry : 1/2 NPT x 2 Enclosure : luminum or S.S. 94V0 POESS Ingress Protection : NEM (IP8) Temperature : PTFE od - 40 to 400 F(- 40 to 204 ) ENVIONMENTL Pressure : max. 2 bar Temperature : - 40 to 140 F (- 40 to 0 ) Material Dielectric: Er >2 Installation ategory : lass II pprovals : F Part 15 - Low Power OPETIONL ommunication Device, E Operation : Pulse adar N/S: 22.2 No M92 +2 ccuracy : +/- 0.1% of max. range in lab using E: IE :90 + 1:92 +2: m current output UL: (2002) +/-0.25% of max. range (typically in field) esponse Time: Standard Unit 2 - echo s / sec. : Std. with less damping echo s / sec. : Fast Protocol 10-0 echo s / sec. Frequency : 5.8 GHz or. GHz. ange ode Loss of Echo : Hold 1min., 22m or 2 m output. Operating NGE esolution Mounting Transmit Power: 50 uw average In Liquids Ferrule alibration : Via communications port (required). Diagnostics : (Echo Profile) via communications port ntenna : Dielectric od Std. PP & Optional PTFE Power BM400 ELETIL SPEIFITIONS 115 V 0 Hz or 20 V 50 Hz (+/-20%), 1.7 V BM00 D 12 to 0 VD, Vdc load = (Vs - ) / 24 m Output 4-20 m Output.1 u resolution 750 Ohms (Isolated on 4 Wire only) Optional S22 or S485 communications port

2 2, & 4 Wire Self ompensating Ultrasonic Transmitters - Sanitary Ferrule Mtg. FETUES S.S. 1L Face Material c/w Tri-lamp Mtg. Base Simple push-button calibration (ccurate) Output 4-20 m / 20-4 m (Isolated on 4 Wire Model s only) Built-in temperature compensation Optional S22 and S485 or HT 7 communications with calibration, diagnostics and data logging software PL compatible Two,Three & Four Wire Operation PPLITIONS Food and Beverages Pharmaceutical /Water ENVIONMENTL Temperature : Electronics Enclosure :- 40 to 140 F (- 40 to 0 ) ontinuous Operation Std. Sanitary Nozzle :- 40 to 140 F (- 40 to 0 ) No Steam leaning (IP) S.S. Sanitary :- 40 to 2 F(- 40 to 10 ) for 1/2 Hr. Steam leaning. emove sensor for longer leaning cycle,recommended. Not for ontinuous Operation Pressure : 5 bar Max. using High Temperature & Pressure Sensor pprovals N/S: 22.2 No M92 +2, E: IE :90 + 1:92 +2:95 UL: (2002) Installation ategory : lass II 5 bar High Temperature & Pressure Sensor OPETIONL 1 bar ccuracy :+/-0.10% of max. range (in lab using 4-20 Ma current output) +/-0.25% of max. range (typically in field) esponse Time: Standard Unit 2 - echo s / sec. : Std. With less damping echo s / sec. : Fast Protocol **I echo s / sec. ** IF equired Beam ngle : degree at db Loss of Echo : Hold 1 min., 22m or 2 m output Temp. omp. : In transducer alibration : Push-button or programmable via optional communications port Diagnostics : (Echo Profile) via communications port MEHNIL onduit Entry : 1/2 NPT Hole (PV conduit only) Enclosure : PV-94V0 or luminum Ingress Protection: NEM (IP8) TLOGUE # - On the Web return to Home Page & efer to catalogue number Structure for ordering Information. In Product Documentation refer to page. TEHNIL SPEIFITIONS ELETIL SPEIFITIONS Power Input - BM V 0 Hz or 20 V 50 Hz (+/-20%), 1.7 V ange ode Beam ngle Operating ange in Liquids ft m ft m ft m ft m esolution mm mm mm mm Mounting Ferrule / /1.5 D- BM00 12 to 0 VD, Vdc load = (Vs ) / 24 m Loop Power - BM200 Output 12 to 28 VD, Vdc 4-20 m Output.1 u esolution 750 Ohms (Isolated on 4 Wire only) Optional S22 or S485 communications port.( & 4 Wire Only)

3 New Feature FETUES S.S. 1L Face Material c/w Ferrule Mtg. Standard 5 feet of interconnection cable Simple push-button calibration Output 4-20 m / 20-4 m Built-in temperature compensation Optional High Level larm relay dual pole output 5/20 Vac Optional S485 communications with calibration, diagnostics and data logging software PL compatible Three Wire Operation PPLITIONS Food and Beverages,Water,Pharmaceutical ENVIONMENTL Temperature : Electronics Enclosure :- 40 to 140 F(- 40 to 0 ) ontinuous Operation Std. Sanitary Nozzle :- 40 to 140 F(- 40 to 0 ) No Steam leaning (IP) S.S. Sanitary :- 40 to 2 F(- 40 to 10 ) for 1/2 Hr. Steam leaning. emoved sensor for longer leaning cycle,recommended. Not for ontinuous Operation Pressure :5 bar Max. using High Temperature & Pressure Sensor Installation ategory: lass II atalogue # - On the Web return to Home Page & efer to atalogue Numbering for Ordering Information. MODEL NGE ESOLUTION MOUNTING BM00-148UMX- PVXXX BM00-081UMX- PVXXX ELETIL SPEIFITIONS Power D Output TEHNIL SPEIFITIONS Optional Mini Sonic Ultrasonic Transmitters - Sanitary Ferrule Mtg ft m ft m mm mm 12 to 0 VD, Vdc load = (Vs ) / 24 m 4-20 m Output.1 u resolution - communications port S Ø.8 Std. Sanitary PV Ferrule 1 1/2 c/w S.S. Face 1.5 / 2.0 Ferrule 1.5 / 2.0 Ferrule 1 bar OPETIONL 5 bar High Temperature & Pressure Sensor S.S. Ferrule 1 1/2 c/w S.S. Face New! Fast Motion Detector 10 echoes / sec. Or Higher ccuracy : +/-0.10% of max. range (in lab using 4-20 Ma current output) +/-0.25% of max. range (typically in field) esponse Time: Standard Unit 2 - echoes / sec. : Std. with less damping echoes / sec. : Fast Protocol **I.. 10 echoes / sec. Or More ** IF equired Beam ngle : degree at db Loss of Echo : Programmable from 1 min. to 4 min. (Default = 1 min.)22m or 2 m output Temp. omp. : In transducer alibration : Push-button or programmable via optional communications port Diagnostics : (Echo Profile) via communications port High Level larm 5. elay has hysteresis and delay of 5% of the tank height, this can be adjusted using communications software. elay s state changes at 20m calibration point or at 4 m calibration point. To switch the above push-button or communication software can be used. Using push-button press and hold until the light goes off. ontinuous green light indicates alarm at 20m.,blinking green indicates alarm at 4 m. elay ON set point is adjustable using communications software. MEHNIL Std. Interconnection able Belden #950 : Pair-24WG 1) Supply 12-0 Vdc 1 pair shielded (ed/blk.) 2) Output 4-20 m 1 Pair shielded (Blk./Green) ) omm. S485 (optional) 1 Pair Shielded (Blk./Wht.) Optional elay able Belden #949 :-18 WG unshielded 1) elay (optional) DPST 5 /20Vac Enclosure PV-94V0 Ingress Protection: NEM (IP8) 10490

4 & 4 Wire Ultrasonic and adar Sensors User Instruction Manual Inter-onnection Diagram Top View of Sensor (ccess over emoved) 12 0 VD D Power Input Note - TB # 7 is onnected to TB # 4! & 4 wire Ultrasonic & adar Level devices provide the power (voltage) to the current loop,so use passive resistive load at PL (controller) input. Terminal Block Status LED alibration Pushbutton NOTE Use only 1/2 NPT onduit Typical Installation 1) Direct mounting ultrasonic sensor - Simply thread sensor directly into metal or plastic nozzle. 2) adar unit must be installed into metal fitting with the antenna pointing downward. ) Do not mount in the center of a domed tank Vdc 115 / 20 Vac 0 / 50 Hz 1/2 NPT onduit Hole Process Mtg. 1,1 1/2,2, NPT Ultrasonic Sensor adar od ntenna! IN /D OUT 4-20 m L1 8 L2/N 7 LIBTION PUSHBUTTON / Led Indicator For 4-20 m (750 ohm Max.) OPTIONL Programmable alibration & Diagnostics, Data Logging, S22 or S485 ommunications. Temperature ompensation for the speed of sound for ultrasonic. Operation - n ultrasonic/electromagnetic pulse is transmitted from the BM sensor. The pulse travels to the surface being monitored and is reflected off this surface back to the sensor. The time of flight is divided by 2,corrected with temp. and converted to an output signal directly proportional to the material level. U Y 4 /TX 2 S22/485 STTUS LIBTION SWITH +/ 0.25% FUSE - F1/8 250V Deadzone S P N BM SENSO TEH. IN E S O L U T I O N Per hart Material Level FULL 20 or 4 m LED Yellow ed EMPTY 4 or 20m F INFOMTION TO D USES NOTE: This equipment has been tested and found to comply with the limits for a lass digital device, pursuant to Part 15 of the F ules. These limits are designed to provided reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. WNING-hanges or Modifications not expressly approved by BM Sensor Technology Inc. could void the user s authority to operate the equipment. Wiring Information - Ground shield at one end only. - ll terminal block wiring must be rated for 250V. - Power input wiring must be protected by a 15 double pole circuit breaker. - Terminal is for use only with equipment which has no live parts which are accessible. - Terminal is for use with equipment which maintains basic insulation from hazardous voltage under normal and single fault conditions. - onnection used at the remote end of external circuit. ecommended Wiring For Sensor Power Wire unshielded 22 WG, 00 V urrent Output 1 Pair shielded 24 WG, 00 V ommunication 1 Pair shielded 24 WG, 00 V For D Sensor Power & urrent output Wire shielded 24 WG, 00 V alibration 4-20 or 20-4 m Output For adar programmable through communication is recommended. FULL alibrate 20 m or 4m (Set Near Target) 1. alibration mode LED color is Green. (for adar Low Dielectric Materials has to be off) 2. Push button and hold until LED turns Yellow (20 m) or push button and hold until LED turns ed (4 m). elease button and observe LED flashes to acknowledge the calibration. EMPTY alibrate 4 m or 20 m (Set Far Target) 1. alibration mode LED color is Green (for adar Low Dielectric Materials has to be off) 2. Push button and hold until LED turns ed (4 m) or push button and hold until LED turns Yellow (20 m). elease button at Yellow or ed and observe LED flashes to acknowledge the calibration. For adar to turn the Low Dielectric Materials operation mode ON and OFF (this mode is recommended for materials with dielectric constant lower than 4 and also to eliminate multiple reflections in tank.) 1) To turn the Low Dielectric Materials ON. Push button and hold until LED goes OFF after the sequence of Yellow,ed and turns Off. The Low Dielectric Material operation is On when the LED S Green light blinks constantly. 2) To turn the Low Dielectric Materials OFF. Push button and hold until LED goes OFF after the sequence of Yellow, ed and Turns OFF. The Low Dielectric Material operation is OFF when LED is continuously Green. ) Use communication software. DWG 10

5 &4 Wire Ultrasonic and adar Sensors ommunication Interconnection Dtl. BM Sensor Terminal Fig. # 1 S22 onnection L1 8 L2/N /TX 2 SHIELD ed DB WHT. or BLK. Note onnect the shield to BM Sensor Terminal #4. BM Sensor Terminal Fig. # 2 S485 onnection L1 8 L2 / N /TX 2 ed WHT. or BLK. S485 to S22 onverter onnect Shield to Ground at one End Note onnect the shield to BM Sensor Terminal #. To P Serial Port onnect to Serial Port of P,use Extension able length as required,efer to Fig.# 1 or # 2 For Wiring Dtl. To Power Source FUSE VD m -- 4! S22/485 /Tx 2 STTUS alibration BM Sensor alibration Switch & Status Led 1/2 PV onduit Only for PV Housings, Metal onduit not ecommended Except for Metal Housing. ULTSONI D 1) Load Probe Gateway P Software into your P. (Select SETUP.EXE from installation D and follow instructions on the screen.) 2) lick on STT and under POGMS select Probe Gateway P. ) Follow instruction in help file.

6 2, & 4 Wire Sanitary Ultrasonic Transmitters Outline Dimensional Dtl. Model# POWE TING : 12-0 Vdc, 0.07 : 24Vdc MB. TEMP. : - 40 TO 0 Deg.. OUTPUT: 4-20m, S ENLOSUE: NEM 4x, IP5 De-energize circuit before removing access cover. UTION! ELETOSTTI ISK SEIL# ID# 4 Ø Nameplate ecess over Tool ccess Hole 4 Ø Thread on wiring access over (PV) 4 / PV Electronic Enclosure.5 Ø O.D. 1/2 NPT onduit Entry Use PV onduit Only Sanitary Ferrule Sanitary Ferrule- O.D. BM 2 Wire Loop powered Probe BM &4 Probe Model # Level Sensor PV Housing Operating Liquid ange Operating Frequency Sanitary Ferrule O.D BMXXX 070ULX-PVS KHz N/ 2.5 BMXXX 080ULX-PVS KHz N/ 2.5 BMXXX 081ULX-PVSXX 1 81 KHz BMXXX 148ULX-PVSXX KHz

7 Mini Sonic Ultrasonic Transmitters Interconnection Diagram 5'(1.5m) 5'(1.5m) Miniprobe - Vdc (blk.)and - m (blk.) are lly connected bration Switch Ø.97" 1" NPT.125" 4.1" 1.95" robe r Box c Sensor - 1" NPT ture ation of sound ture - 5'(1.5m) U Y E S S O P L U N T I O N Fill Ø1.125" alibration or 20-4 m Output FULL - alibration 20 m or 4 m(set Near Target) 1. alibration mode LED colour is Green. LED 2. Push button and hold until LED turns Yellow (20m) or push button and hold until LED turns ed ( 4 m).. elease button, observe LED flashes to acknowledge the calibration. EMPTY - alibrate 4m or 20m (Set Far Target) 1. alibration mode LED colour is Green. 2. Push button and hold until LED turns ed ( 4m) or push button and hold until LED turns Yellow (20ma).. elease button, observe LED flashes to acknowledge the calibration Operation - n ultrasonic pulse is transmitted from the BM sensor. The pulse travels to the surface being monitored and is reflected off this surface back to the sensor. The time of flight is divided by 2, corrected with temperature and converted to an output signal directly proportional to the material level. 11