B250, 2-Way, Characterized Control Valve Stainless Steel Ball and Stem

Transcription

1 250, 2-ay, haracterized ontrol Valve Stainless Steel all and Stem pplication This valve is typically used in air handling units on heating or cooling coils, and fan coil unit heating or cooling coils. Some other common applications include Unit Ventilators, VV box re-heat coils and bypass loops. This valve is suitable for use in a hydronic system with variable flow. Suitable ctuators Non-Spring Spring 250 (X) (X) imensions (Inches [mm]) ate created, 10/27/ Subject to change. elimo ircontrols (US), Inc. Technical ata 2090 Service chilled, hot water, up to 60% glycol low haracteristic equal percentage ontrollable low ange 75 Size [mm] 2 [50] nd itting NPT female ends ody forged brass, nickel plated all stainless steel Stem stainless steel Stem Packing PM (lubricated) Seat Teflon PT Seat O-ring PM (lubricated) haracterized isc No isc (full flow) ody Pressure ating [psi] 400 Media Temperature ange 0 to 250 [-18 to 120 ] (ater) Max ifferential Pressure (ater) 50 psi (345 kpa) lose-off Pressure 200 psi v 57 eight 2.9 lb [1.3 kg] Leakage 0% for to Servicing maintenance free low Pattern H1, X H2 H1 H2 10 [254] 4.21 [107] 6.84 [174] 5.51 [140] 1.73 [44] 1.18 [30] 0.5 [15] US N LTIN MI / IN

2 250, 2-ay, haracterized ontrol Valve Stainless Steel all and Stem imensions (Inches [mm]) imensions (Inches [mm]) N4, X N4, N N4, NX N4 N4, X N [289] 4.21 [107] 9.8 [9] 7.55 [192] 3.15 [80] [330] 4.93 [125] [261] 9. [5] 3.39 [86] imensions (Inches [mm]) H1 H2 Q, QX H1 H2 9.9 [251] 4.21 [107] 7.45 [190] 6.11 [155] 2.28 [58] 0.75 [20] 0.5 [15] imensions (Inches [mm]), X ate created, 10/27/ Subject to change. elimo ircontrols (US), Inc [275] 4.21 [107] 9.47 [1] 8.14 [207] 2.02 [51] US N LTIN MI / IN

3 X-MT95 Modulating, Non-Spring eturn, V, 0 to 135 Ω Input ate created, 11/30/ Subject to change. elimo ircontrols (US), Inc. Technical ata 25 Power Supply V, ±20%, 50/60 Hz, V, ±10% Power onsumption unning 3.5 Power onsumption Holding 1.3 Transformer Sizing 6 V (class 2 power source) lectrical onnection 18 G plenum rated cable with 1/2 conduit connector protected NM 2 (IP54) 3ft [1m] 10ft [3m] and 16ft [5m] Overload Protection electronic thoughout 0 to 90 rotation Operating ange Y 0 to 135 Ω Honeywell lectronic, 0 to 135 Ω input Input Impedance 100 k Ω eedback Output U 2 to 10 V, 0.5 m max, V variable ngle of otation 90 irection of otation (Motor) reversible with built-in switch Position Indication integrated into handle Manual Override external push button unning Time (Motor) 150 sec mbient Temperature ange - to 1 [-30 to 50 ] Storage Temperature ange -40 to 176 [-40 to 80 ] Housing NM 2, IP54 gency Listings culus acc. to UL /-2-14, N/S :02, acc. to 2004/108/ and 2006/95/ Noise Level (Motor) <45 d () Servicing maintenance free Quality Standard ISO 9001 ated Impulse Voltage 800V, Type action 1, ontrol Pollution egree US N LTIN MI / IN

4 X-MT95 Modulating, Non-Spring eturn, V, 0 to 135 Ω Input iring iagrams INSTLLTION NOTS Provide overload protection and disconnect as required. ctuators may also be powered by V. ctuators with plenum cable do not have numbers; use color codes instead. ctuators and controller must have separate transformers. onsult controller instruction data for more detailed information. esistor value depends on the type of controller and the number of actuators. No resistor is used for one actuator. Honeywell resistor kits may also be used. To reverse control rotation, use the reversing switch. ctuators may be controlled in parallel. urrent draw and input impedance must be observed. Meets culus requirements without the need of an electrical ground connection.! NING! LIV LTIL OMPONNTS! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. ailure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Switch Switch amper Position amper Open amper losed The direction of rotation switch is set so that the fail safe position and the position of the damper is closed with no signal at wire. Typical and Override ontrol low limit control 135 for 0 to 50% control 280 for 0 to 100% control Low Limit ontrol 135 lk (1) ed (2) ht (3) lk (1) ed (2) Pnk ht Gry Org (6) (3) (7) (5) lk (1) ed (2) Pnk ht Gry Org (6) (3) (7) (5) low limit control High Limit ontrol lk (1) ed (2) ht (3) Shunting esistor lk (1) ed (2) + Hot ht (3) ate created, 11/30/ Subject to change. elimo ircontrols (US), Inc. No. of actuators esistance esistor Kit No. ZG-03 Multiple ctuators lk (1) ed (2) + Hot ht (3) US N LTIN MI / IN

5 X-MT95 Modulating, Non-Spring eturn, V, 0 to 135 Ω Input S963 Minimum Position Potentiometer Shunting esistor H205 hangeover Occupied ontact lk (1) ed (2) ht (3) + Hot lk (1) ed (2) + Hot ht (3) Multiple ctuators with Minimum Position Potentiometer Q209 Minimum Position Potentiometer H205 hangeover lk (1) ed (2) ht (3) Shunting esistor Y 973, 7100 Occupied ontact Honeywell T675 Morning armup lk (1) ed (2) ate created, 11/30/ Subject to change. elimo ircontrols (US), Inc. No. of actuators esistance ht (3) Ω Ω Ω Used with the 973 and 7100 controllers Honeywell Q209 Minimum Position Potentiometer Shunting esistor 973, 7100 T775 Honeywell T675 Morning armup ht (3) lk (1) ed (2) ht (3) lk (1) ed (2) Multiple ctuators Used with 973, 7100 and T US N LTIN MI / IN