Electrical data Nominal voltage AC/DC 24 V Nominal voltage frequency

Transcription

1 echnical data sheet LH24A-00 Communicative linear actuator adjusting dampers and slide valves in technical building installations Air damper size up to approx. m² Actuating force 50 N Nominal voltage AC/DC 24 V Control communicative, modulating DC (0)2...0 V Variable Position feedback DC V Variable Length of Stroke Max. 00 mm, adjustable in 20 mm increments Conversion of sensor signals Communication via Belimo -Bus echnical data Electrical data Nominal voltage AC/DC 24 V Nominal voltage frequency 50/60 Hz Nominal voltage range AC V / DC V Power consumption in operation 2.5 W Power consumption in rest position.3 W Power consumption for wire sizing 5 VA Connection supply / control Cable m, 4 x 0.75 mm² Parallel operation es (note the performance data) Functional data Actuating force motor Min. 50 N Modifiable actuating force 25%, 50%, 75% reduziert Positioning signal DC V Positioning signal note Input impedance 00 kω Control signal variable Open-close 3-point (AC only) Modulating (DC V) Operating range DC V Operating range variable Start point DC V End point DC V Position feedback DC V Position feedback note Max. 0.5 ma Position feedback variable Start point DC V End point DC V Position accuracy ±5% Direction of motion motor Selectable with switch Direction of motion note = 0 V: with switch 0 (retracted) / (extended) Direction of motion variable Electronically reversible Manual override With push-button, can be locked Length of Stroke Max. 00 mm, adjustable in 20 mm increments Stroke limitation can be limited on both sides with mechanical end stops Running time motor 50 s / 00 mm Motor running time variable s / 00 mm Adaption setting range manual Adaption setting range variable No action Adaption when switched on Adaption after pushing the gear disengagement button Override control MAX (maximum position) = 00% MIN (minimum position) = 0% ZS (intermediate position, AC only) = 50% Override control variable MAX = (MIN + 32%)...00% MIN = 0%...(MAX 32%) ZS = MIN...MAX Sound power level motor 45 db(a) Safety Protection class IEC/EN III Safety extra-low voltage Protection class L L Class 2 Supply Degree of protection IEC/EN IP54 Degree of protection NEMA/L NEMA 2, L Enclosure ype 2 EMC CE according to 204/30/E LH24A-00 en-gb subject to changes

2 echnical data Safety Certification IEC/EN IEC/EN and IEC/EN Certification L clus according to L A, L and CAN/CSA E60730-:02 Mode of operation ype Rated impulse voltage supply / control 0.8 kv Control pollution degree 3 Ambient temperature C Non-operating temperature C Ambient humidity 95% r.h., non-condensing Maintenance Maintenance-free Weight Weight 0.52 kg Safety notes! he device must not be used outside the specified field of application, especially not in aircraft or in any other airborne means of transport. Outdoor application: only possible in case that no (sea)water, snow, ice, insolation or aggressive gases interfere directly with the actuator and that is ensured that the ambient conditions remain at any time within the thresholds according to the data sheet. Only authorised specialists may carry out installation. All applicable legal or institutional installation regulations must be complied during installation. he device may only be opened at the manufacturer s site. It does not contain any parts that can be replaced or repaired by the user. Cables must not be removed from the device. he rotary supports and coupling pieces available as accessories must always be used if transverse forces are likely. In addition, the actuator must not be tightly bolted to the application. It must remain movable via the rotary support (refer to «Assembly notes»). If the actuator is exposed to severely contaminated ambient air, appropriate precautions must be taken on the system side. Excessive deposits of dust, soot etc. can prevent the gear rod from being extended and retracted correctly. If not installed horizontally, the gear disengagement pushbutton may only be actuated when there is no pressure on the gear rod. o calculate the actuating force required for air dampers and slide valves, the specifications supplied by the damper manufacturers concerning the cross section, the design, the installation site and the ventilation conditions must be observed. If a rotary support and/or coupling piece is used, actuation force losses are to be expected. he device contains electrical and electronic components and must not be disposed of as household refuse. All locally valid regulations and requirements must be observed. Product features Mode of operation Converter for sensors Parameterisable actuators Conventional operation: he actuator is connected with a standard modulating signal of DC 0...0V and drives to the position defined by the positioning signal. Measuring voltage serves for the electrical display of the damper position % and as slave control signal for other actuators. Operation on the -Bus: he actuator receives its digital positioning signal from the higher level controller via the -Bus and drives to the position defined. Connection serves as communication interface and does not supply an analogue measuring voltage. Connection option for a sensor (passive or active sensor or switching contact). he actuator serves as an analogue/digital converter for the transmission of the sensor signal via -Bus to the higher level system. he factory settings cover the most common applications. Single parameters can be modified with the Belimo Service ools MF-P or ZH E. 2 LH24A-00 en-gb subject to changes

3 Product features Simple direct mounting Manual override Adjustable stroke High functional reliability Home position he actuator can be directly connected with the application using the enclosed screws. he head of the gear rod is connected to the moving part of the ventilating application individually on the mounting side or with the Z-KS2 coupling piece provided. Manual override with push-button possible (the gear is disengaged for as long as the button is pressed or remains locked). If a stroke limitation will be adjusted, the mechanical operating range on this side of the gear rod can be used starting with an extension length of 20 mm and then can be limited respectively in increments of 20 mm by means of mechanical end stops Z-AS2. he actuator is overload protected, requires no limit switches in intermediate positions and automatically stops when the end stop is reached (at rest). he first time the supply voltage is switched on, i.e. at the time of commissioning, the actuator carries out a synchronisation. he synchronisation is in the home position (0%). he actuator then moves into the position defined by the positioning signal. 0 = 0 V = 0 V Adaption and synchronisation An adaption can be triggered manually by pressing the Adaption button or with the PC-ool. Both mechanical end stops are detected during the adaption (entire setting range). Automatic synchronisation after pressing the gearbox disengagement button is configured. he synchronisation is in the home position (0%). he actuator then moves into the position defined by the positioning signal. A range of settings can be adapted using the PC-ool (see MF-P documentation) Accessories Description ype Gateways Gateway to Modbus R, AC/DC 24 V K24MOD Gateway for BACnet MS/P, AC/DC 24 V K24BAC Gateway to LonWorks, AC/DC 24 V, LonMark certified K24LON Gateway to KNX, AC/DC 24 V, EIBA certified K24EIB Electrical accessories Description Digital position indicator for front-panel mounting, %, front mass 72 x 72 mm Range controller for wall mounting, adjustable electron. Min./max. angle of rotation limitation Positioner for wall mounting, range % Positioner in a conduit box, range % Positioner for front-panel mounting, range % Positioner for wall mounting, range % Connecting cable 5 m, A+B: RJ2 6/6, o ZH/ZIP-SB- Connection cable 5 m, A: RJ 6/4, B: Free wire end, o ZH/ZIP- SB- ype ZAD24 SBG24 SGA24 SGE24 SGF24 CRP24-B ZK-GEN ZK2-GEN Description Mechanical accessories End stop set for LH Z-AS2 Rotary support for compensation of transverse forces Z-DS Coupling piece M6 for LH, galvanised steel Z-KS2 ype Service ools Description Service ool, for MF//Modbus/LonWorks actuators and VAV- Controller Belimo PC-ool, software for adjustments and diagnostics Adapter to Service ool ZH ype ZH E MF-P MF-C LH24A-00 en-gb subject to changes 3

4 Electrical installation! Notes Connection via safety isolating transformer. Parallel connection of other actuators possible. Observe the performance data. Wiring diagrams AC/DC 24 V, modulating Operation on the -Bus DC (0)2 0 V DC 2 0 V Sensor Cable colours: = black 2 = red 3 = white 5 = orange Cable colours: = black 2 = red 3 = white 5 = orange Functions Functions when operated on -Bus Connection on the -Bus Network topology + A) Connection of active sensors A) more actuators and sensors (max.8) Connection of external switching contact here are no restrictions for the network topology (star, ring, tree or mixed forms are permitted). Supply and communication in one and the same 3-wire cable no shielding or twisting necessary no terminating resistors required + p + A) A) A) more actuators and sensors (max.8) Supply AC/DC 24 V Output signal DC V (max. DC V) Resolution 30 mv A) more actuators and sensors (max.8) Switching current 6 24 V Start point of the operating range must be parameterised on the actuator as 0.5 V Connection of passive sensors + A) Ni C Ω 2) P C Ω 2) NC C ) 200 Ω...60 kω 2) A) more actuators and sensors (max.8) ) Depending on the type 2) Resolution Ohm 4 LH24A-00 en-gb subject to changes

5 Functions Functions with basic values (conventional mode) Override control with AC 24 V with relay contacts Override control with AC 24 V with rotary switch a b c (DC V) 0% ZS 50% 00% (DC V) e.g. N % ZS 50% a b c e.g. N % Remote control % with positioner SG.. Minimum limit with positioner SG.. Z SGA24 SGF24 SGE24 Z SGA24 SGF24 SGE24 0 [V] (DC V) min 0 [%] 0 00 Follow-up control (position-dependent) Position indication DC (0)2 0 V DC 2 0 V ZAD ) ) Adapting the direction of stroke Control with ma via external resistor Functional check 500 Ω ( ) (+) 4 20 ma DC 2 0 V Caution: he operating range must be set to DC V. he 500 Ω resistor converts the ma current signal to a voltage signal DC V Procedure. Apply 24 V to connection and 2 2. Disconnect connection 3: - for direction of stroke 0: Actuator travels in the direction retracted - for direction of stroke : Actuator travels in the direction extended 3. Short circuit connections 2 and 3: - Actuator runs in the opposite direction LH24A-00 en-gb subject to changes 5

6 Functions Functions for actuators with specific parameters (Parametrisation with PC-ool necessary) Override control and limiting with AC 24 V with relay contacts Override control and limiting with AC 24 V with rotary switch a b c d e (DC V) Close ) MIN ZS MAX Open (DC V) e.g. N 4007 Close ) MIN ZS MAX Open a b c d e e.g. N 4007 ) Caution: his function is only guaranteed if the start point of the operating range is defined as min. 0.5 V. Control open-close Control 3-point a b e.g. N 4007 a b 0 0 Operating controls and indicators 4 Adaption Adress Power 3 Status Direction of stroke switch Switch over: Direction of stroke changes 2 Push-button and LED display green Off: No power supply or malfunction On: In operation Press button: riggers stroke adaptation, followed by standard mode 3 Push-button and LED display yellow Off: Standard mode Flickering: communication active On: Adaptation or synchronising process active Flashing: Request for addressing from master Press button: Confirmation of the addressing 4 Gear disengagement button Press button: Gear disengages, motor stops, manual override possible Release button: Gear engages, synchronisation starts, followed by standard mode 5 Service plug For connecting parameterisation and service tools Check power supply connection 2 Off and 3 On Possible wiring error in power supply 6 LH24A-00 en-gb subject to changes

7 Installation notes! Notes If a rotary support and/or coupling piece is used, losses in the actuation force losses are to be expected. Applications without transverse force Applications with transverse forces he linear actuator is screwed directly to the housing at three points. Afterwards, the head of the gear rod is fastened to the moving part of the ventilation application (e.g. damper or slide valve). Connect the coupling piece with the internal thread (Z-KS2) to the head of the gear rod. Screw the rotary support (Z-DS) to the ventilation application. Afterwards, the linear actuator is screwed to the previously mounted rotary support with the enclosed screw. Afterwards, the coupling piece, which is mounted to the head of the gear rod, is attached to the moving part of the ventilating application (e.g. damper or slide valve). he transverse forces can be compensated for to a certain limit with the rotary support and/or coupling piece. he maximum permissible swivel angle of the rotary support and coupling piece is 0, laterally and upwards. Service Service ools connection he actuator can be parameterised by ZH E via the service socket. For an extended parameterisation the PC tool can be connected. AC 24 V DC 24 V SB ZH E i esc OK BELIMO PC-ool SB Dimensions [mm] Dimensional drawings LH24A-00 en-gb subject to changes 7

8 Further documentation Overview Cooperation Partners ool connections 8 LH24A-00 en-gb subject to changes