This specification describes the minimum requirements for service water piping systems (ie: cooling water, process water, etc.), located on surface.

Size: px
Start display at page:

Download "This specification describes the minimum requirements for service water piping systems (ie: cooling water, process water, etc.), located on surface."

Transcription

1 SPEC /9 1.0 PURPOSE This specification describes the minimum requirements for service water piping systems (ie: cooling water, process water, etc.), located on surface. Note: This specification does not apply to piping for sprinkler systems, potable water, buried services or underground installations. 2.0 AND FITTINGS Design Condition Operating Conditions Design Fabrication Installation Approvals Pipe o F to 19 o F o F to 110 o F In accordance with this specification and SPEC Piping General Requirements CSA B51 Boiler, Pressure Vessel and Pressure Piping Code ASME B31.1 Power Piping Cold water piping systems are not subject to approval by regulatory agencies. 1 ½ " & Smaller Schedule 0 per ASME B36.10, carbon steel ASTM A53 Gr. B, ERW or seamless, threaded ends. 2" through 10" Schedule 0 per ASME B36.10, carbon steel ASTM A53 Gr. B, ERW or seamless, beveled ends. 12" through 16" 0.375" thick wall per ASME B36.10, carbon steel ASTM A53 Gr. B, ERW or seamless, beveled ends. 20" through 30" " thick wall per ASME B36.10, carbon steel ASTM A139, Grade A or B, beveled ends.

2 SPEC /9 1 ½ " & Smaller Fittings Class 150 malleable iron per ASME B16.3, ASTM A197, screwed and banded. 2" through 10" Schedule 0 per ASME B16.9, carbon steel ASTM A23 Grade WPB, butt weld. 12" & Above 0.375" thick wall per ASME B16.9, carbon steel ASTM A23 WPB, butt weld. Butt weld elbows to be long radius R = 1 1/2 x dia. unless otherwise noted. Branch Connections See Table 1 - Attach to run pipe by full penetration welds. Threaded and socket weld half couplings, Class 3000 per ASME B16.11, forged carbon steel ASTM A105 Thredolet and sockolet, Class 3000 per ASME B16.11 and MSS SP-97, forged carbon steel ASTM A105 Weldolet, Extra strong per ASME B16.11 and MSS SP-97, forged carbon steel ASTM A105 Flanges 1 ½ " & Smaller Threaded type, raised face, Class 150 per ASME B16.5, forged carbon steel ASTM A105. Use flanges 1½ " and smaller only for connections to flanged equipment 2" through 2" Slip-on or welding neck type, raised face, Class 150 per ASME B16.5, forged steel ASTM A105. Bore of welding neck flanges to suit pipe ID. 26" through 30" Welding neck type, raised face, Class 150 per MSS SP-, forged carbon steel ASTM A105. Bore of welding neck flanges to suit pipe ID. Note: Flat faced flanges required at cast iron valves and flanges, for all sizes.

3 SPEC /9 Threaded Joint Sealants Do not use wet sealants. Use teflon tape. Flanged Joints Gaskets Flange Bolting Welded Joints Unions Ball Valves 1/16" flat ring type for raised face inside bolts, non-asbestos, synthetic fibre, nitrile bonding. Dimensions per ASME B Full face gasket required at flat face flanges. Gasket dope is not permitted. Manufacturer's gasket material recommendation subject to Vale approval. Carbon steel bolts to ASTM A307 Grade B, UNC threads with heavy hex nuts to ASTM A563 Grade A. Use Class 2A fit on bolts and 2B fit on nuts. Dimension per ASME B1.1, B and B Essential variables to be in accordance with SPEC for the welding procedure (WP) identified. All sizes WP1 1 ½ " & Smaller Class 150 per ASME B16.39, malleable iron ASTM A197, brass to brass seats, spherically ground joints, threaded ends to ASME B ½ " & Smaller Class 00 minimum rating brass body and ball, stainless steel or brass stem, teflon seats, reinforced teflon seals, threaded ends to ASME B Valves to be lockable.

4 SPEC-3500 /9 2" through 6" Butterfly Valves Class 125 cast iron body wafer style for mounting between ASME Class 150 flanges, 316 stainless steel shaft and disc, EPDM seat, lever operated, rated 200 PSIG minimum differential in closed position, face to face dimensions in accordance with MSS SP-67. Valves to be lockable. 8" & Above Same as above except shall have gear operator actuator and rated 150 PSIG minimum differential in closed position. Valves to be lockable. Notes: 1. Where slow opening characteristics are required for the above butterfly valves (to reduce the possibility of water hammer) replace the lever operator with optional gear operator 2. Lug style butterfly valves with through tapped holes to be used in dead end service or where line blinds are used for maintenance purposes. 3. Use Buna N seats where water is contaminated with oil, or where possibility of oil contamination exists. Gate Valves Globe Valves 2" & Above Class 125, flanged, iron body, bronze mounted, wedge disc, outside stem and yoke, rising stem. Valves to be lockable. 1 ½ " & Below Class 150, threaded, brass or bronze body, composition disc, inside screw. Valves to be lockable. 2" through 10" Class 125, flanged, iron body, bronze disc and seat, outside stem and yoke. Valves to be lockable. Check Valves 1 ½ " & Below Class 125, bronze swing check per ASTM B61 or B62, integral seat, bronze disc, screwed or union cap, threaded. 2" & Above Class 125, ductile iron body or cast iron body wafer style non-slam check valve, 316 stainless steel disc, Buna N seat, Inconel X or 316 SS spring. Safety Relief Valves Selection by the Engineer.

5 SPEC /9 Pressure Reducing Valves Strainers Instrumentation Isolating Valves Selection by the Engineer. 1½ " & Below Class 250, iron body Y-Type strainer, screwed cap complete with blowoff connection and plug, 1/32" perforated stainless steel screen, threaded ends to ASME B " & Above Class 125, iron body Y-Type strainer, bolted cover complete with blowoff connection and plug, 1/32" perforated stainless steel screen, flanged ends to ASME B16.1. ½ " size ball valve, class 00, minimum rating brass body and ball, stainless steel or brass stem, teflon seats, reinforced teflon seals, threaded to ASME B Valves to be lockable. 3.0 TESTING Testing must meet the requirements of ASME B31.1 and PROC (hydrostatic testing) or SPEC (pneumatic testing only at the discretion of the Engineer) and specific instructions in the scope of work. Test Pressure Duration Additional Requirements 225 PSIG Per Code none.0 EXAMINATION AND INSPECTION Examination and inspection must meet the requirements of ASME B31.1 and specific instructions in the scope of work. Minimum 100% visual examination for pressure welds or welds to pressure retaining components and a complete inspection. 5.0 PAINTING-PIPE SYSTEM CLASSIFICATION AND IDENTIFICATION The piping system shall be painted (classification) and labeled (identification) in accordance with SPEC

6 SPEC /9

7 SPEC /9 6.0 REFERENCE DOCUMENTATION The following documents were used in the development of this document or have instructions and procedures applicable to it. They shall be used in their most recent revision. SPEC SPEC SPEC SPEC-3508 PROC SPEC CSA B51 CSA Z180.1 ASME B31.1 ASTM A53 ASTM A23 ASTM A105 ASTM A106 ASTM B61 ASTM B62 ASTM F681 ASTM A139 ASTM A536 ASTM A563 ASTM D2000 ASTM A307 ASTM A179 ASTM A193 ASTM A19 ASME B16.1 Identification and Classification Piping General Requirements Welding Process Requirements Requirements for Pneumatic Testing of Piping Systems Hydrostatic Testing Buried Pipelines Water Boiler, Pressure Vessel and Pressure Piping Code Compressed Breathing Air and Systems Power Piping Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service Standard Specification for Carbon Steel Forgings for Piping Applications Standard Specification for Seamless Carbon Steel Pipe for High Temperature Service Standard Specification for Steam or Valve Bronze Castings Standard Specification for Composition Bronze or Ounce Metal Castings Standard Practice for use of Branch Connections Standard Specification for Arc Welded Steel Pipe Standard Specification for Ductile Iron Castings Specification for Carbon and Alloy Steel Nuts Standard Classification System for Rubber Products in Automotive Application Specification for Carbon Steel Bolts and Studs, 60,000 PSI Tensile Strength Standard Specification for Seamless Cold-Drawn Low-Carbon Steel Heat- Exchanger and Condenser Tubes Standard Specification for Alloy Steel and Stainless Steel Bolting for High Temperature Service or High Pressure Service Standard Specification for Carbon Steel and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service or Both Gray Iron Pipe Flanges and Flange Fittings

8 SPEC-3500 ASME B16.3 Malleable Iron Threaded Fittings ASME B16.5 Pipe Flanges and Flanged Fittings ASME B16.9 Factory-Made Wrought Buttwelding Fittings ASME B16.11 Forged fittings Socket Welded and Threaded ASME B16.21 Nonmetallic Flat Gaskets for Pipe Flanges ASME B16.3 ASME B36.10 ASME B ASME B ASME B1.1 ASME B16.39 ASME B ASME B16.25 MSS SP- MSS SP-67 MSS SP-83 MSS SP-97 8/9 Valves Flanged, Threaded and Welding Ends Welded and Seamless Wrought Steel Pipe Square, Hex, Heavy Hex, and Askew Head Bolts and Hex, Heavy Hex, Hex Flange, Lobed Head, and Lag Screws (Inch Series) Nuts for General Applications: Machine Screw Nuts, Hex, Square, Hex Flange, and Coupling Nuts (Inch Series) Unified Inch Screw Threads Malleable Iron Threaded Pipe Unions Pipe Threads, General Purpose (Inch) Butt Welding Ends Steel Pipeline Flanges Butterfly Valves Class 3000 Steel Pipe Unions, Socket Welding and Threaded Integrally Reinforced Forged Branch Outlet Fitting

9 SPEC /9 7.0 REVISION AND TRANSITION NOTES Revision notes describe: what was changed, and if applicable, why it was changed, and the plan to implement the change, including whether changes are retroactive Rev 1 Description Specification updated and format and number revised. Previous number Rev 9 2 Approved for use in Thompson No Changes 3 Section 1: Reworded and added for clarity does not apply to underground installations. Section 3: Added some reference codes and/or standards Section : Changed Pressure Rating to Design Conditions, added temperature range to design and operating conditions. Added ASME B36.10 references to the Pipe Section. The lb. was removed from Class designations per ASME definition. Added ASME B16.11 and MSS SP-97 reference to Branch Connection section. Nuts and bolts to be the same across flats comment removed from Flange Bolting section as dimension will be as per code. Gasket section title replaced with Pipe Joint title and now includes welding section, flange bolts section and gasket section. Replaced incorrect SPEC with SPEC in Welded Joint section. Add full face gaskets required at flat face flanges. Changed pressure differential across 8 and Above Butterfly Valves from 200 PSIG to 150 PSIG, as this is Industry Standard. Section 5: Added table, added SPEC-3508 and PROC reference. Removed duplicate content that is in the SPEC or PROC. Section 6: Added Inspection to title. Added inspection criteria per code. Clarified examination requirements. Section 7: Changed section title for clarity. Revision by JB 2011/10/11 JB 2011/10/11 Approved by JB 2012/01/26 JB 2012/01/26 Issue Date YYYY/MM/ DD 2012/0/ /08/09 M.Fogarty M.Fogarty 2015/12/23 Format updated Globe valve 1 ½ & smaller now brass or bronze Check valve 2 & above now ductile or cast iron body -spring materials now Inconel X or 316SS Butterfly valve Changed aluminum bronze disc to SS. M.Fogarty M.Fogarty

This specification describes the minimum requirements for piping systems for the following service:

This specification describes the minimum requirements for piping systems for the following service: SPEC-3004 1/7 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Service Water Design Conditions Operating Conditions 10 PSIG @ 33 o F to

More information

This specification describes the minimum requirements for piping systems for the following service:

This specification describes the minimum requirements for piping systems for the following service: SPEC-3501 1/ 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Instrument Air Design Conditions 150 PSIG @ 180 F Operating Conditions 125

More information

This specification describes the minimum requirements for piping systems for the following service:

This specification describes the minimum requirements for piping systems for the following service: 201/11/2 1/9 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Underground Service Water Note: This specification does not apply to piping

More information

This specification describes the minimum requirements for piping systems for the following service:

This specification describes the minimum requirements for piping systems for the following service: 201/01/13 1/ 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Service Air Design Conditions Operating Conditions Blast Air (see Note 1)

More information

A representative from Occupational Health is to be involved in the commissioning process to address any Respiratory Protection Program requirements.

A representative from Occupational Health is to be involved in the commissioning process to address any Respiratory Protection Program requirements. SPEC-3017 1/8 1.0 PURPOSE This specification describes the minimum requirements for the installation of breathing air distribution systems (indoor and outdoor) up to the connection to the breathing air

More information

Note: Do not bury sulphur dioxide lines Use stainless steel pipe and fittings only where specified on project drawings.

Note: Do not bury sulphur dioxide lines Use stainless steel pipe and fittings only where specified on project drawings. 1/7 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Liquid and High Pressure Gaseous Dry Sulphur Dioxide (Less than 100 ppm of water)

More information

.1 Materials and installation for steel piping, valves and fittings for hydronic systems in building services piping..2 Related Sections.

.1 Materials and installation for steel piping, valves and fittings for hydronic systems in building services piping..2 Related Sections. Issued 2006/08/01 Section 15183 Hydronic Systems: Steel Page 1 of 6 PART 1 GENERAL 1.1 SUMMARY.1 Section Includes..1 Materials and installation for steel piping, valves and fittings for hydronic systems

More information

Allentown, PA - Plant Expansion Steel Pipe Spec. No. 671-S40 December 31, 2015

Allentown, PA - Plant Expansion Steel Pipe Spec. No. 671-S40 December 31, 2015 Steel DIVISION 15: MECHANICAL SECTION 15061: STEEL PIPE 1.0 GENERAL All materials shall be of high quality and as per the following specifications. 2.0 PRODUCTS 2.1 Specification CS-1 Service = (CA, VAC)

More information

SECTION BASIC MATERIALS AND METHODS

SECTION BASIC MATERIALS AND METHODS SECTION 15050 BASIC MATERIALS AND METHODS PART 1 - GENERAL 1.01 SECTION INCLUDES A. Pipe and Fittings. 1.02 RELATED SECTIONS A. Basic Mechanical Requirements: Section 15010. B. Supports, Anchors, and Seals:

More information

SECTION EXPANSION FITTINGS AND LOOPS FOR HVAC PIPING

SECTION EXPANSION FITTINGS AND LOOPS FOR HVAC PIPING SECTION 230516 - EXPANSION FITTINGS AND LOOPS FOR HVAC PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and

More information

FUEL GAS PIPING SECTION A. The provisions of SECTION 15010, MECHANICAL GENERAL REQUIREMENTS, apply to this section.

FUEL GAS PIPING SECTION A. The provisions of SECTION 15010, MECHANICAL GENERAL REQUIREMENTS, apply to this section. FUEL GAS PIPING SECTION 15355 PART 1 GENERAL 1.1 DESCRIPTION A. The provisions of SECTION 15010, MECHANICAL GENERAL REQUIREMENTS, apply to this section. B. This specification covers both interior and exterior

More information

Essex County College - West Essex Campus Addition And Renovations dlb # / SECTION EXPANSION FITTINGS AND LOOPS FOR HVAC PIPING

Essex County College - West Essex Campus Addition And Renovations dlb # / SECTION EXPANSION FITTINGS AND LOOPS FOR HVAC PIPING SECTION 230516 - EXPANSION FITTINGS AND LOOPS FOR HVAC PIPING PART I - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and

More information

HYDRONIC PIPING

HYDRONIC PIPING SECTION 23 21 13 HYDRONIC PIPING PART 1 GENERAL 1.01 SECTION INCLUDES A. Hydronic system requirements. B. Heating water piping, above grade. C. Chilled water piping, above grade. D. Condenser water piping,

More information

QUALITY ASSURANCE SPECIFICATION

QUALITY ASSURANCE SPECIFICATION Page 1 of 8 QAS: 2.02 QUALITY ASSURANCE SPECIFICATION REVISION: 0 DATE: 08/29/14 MATERIAL PURCHASING Code Material Purchase Specification for Pipe, Valves, Fitting, and Flanges PAGE 1 OF 8 1.0 Purpose

More information

We Are the Worldwide Provider for All Your Valve and Fitting Needs

We Are the Worldwide Provider for All Your Valve and Fitting Needs Product Catalog We Are the Worldwide Provider for All Your and Fitting Needs C&C strives to earn your business by offering an extensive line of high quality products with a proven track record for successful

More information

A. Compatibility: Products shall be suitable for piping service fluids, materials, working pressures, and temperatures.

A. Compatibility: Products shall be suitable for piping service fluids, materials, working pressures, and temperatures. SECTION 22 05 16 LOOPS FOR PLUMBING PIPING PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

Application for design registration

Application for design registration Avis au lecteur sur l accessibilité : Ce document est conforme au standard du gouvernement du Québec SGQRI 008-02 afin d être accessible à toute personne handicapée ou non. Toutes les notices entre accolades

More information

MATERIAL COMBINATION NUMBER 2: Corrosive environment requiring harder, wear-resistant seating faces and resistance to dezincification.

MATERIAL COMBINATION NUMBER 2: Corrosive environment requiring harder, wear-resistant seating faces and resistance to dezincification. Cast Iron Slide Gates Spec Sheet General The contractor shall furnish and install the following cast iron slide gate assemblies as listed on the Gate Schedule and detailed on the manufacturer s drawings.

More information

Page 1 of 12 Second Revision No. 5-NFPA 12-2014 [ Section No. 2.3.4 ] 2.3.4 ASTM Publications. ASTM International, 100 Barr Harbor Drive, P.O. Box C 700, West Conshohocken, PA 19428-2959. ASTM A53, Standard

More information

NAVSEA STANDARD ITEM T9074-AS-GIB-010/271, Requirements for Nondestructive Testing Methods

NAVSEA STANDARD ITEM T9074-AS-GIB-010/271, Requirements for Nondestructive Testing Methods NAVSEA STANDARD ITEM ITEM NO: 009-48 DATE: 29 JUL 2011 CATEGORY: II 1. SCOPE: 1.1 Title: Pressure Seal Bonnet Valve; repair (shop) 2. REFERENCES: 2.1 S9086-CJ-STM-010/CH-075, Fasteners 2.2. T9074-AS-GIB-010/271,

More information

SAUSALITO-MARIN CITY SANITARY DISTRICT MISCELLANEOUS UPGRADES PROJECT. Addendum No. 2

SAUSALITO-MARIN CITY SANITARY DISTRICT MISCELLANEOUS UPGRADES PROJECT. Addendum No. 2 SAUSALITO-MARIN CITY SANITARY DISTRICT MISCELLANEOUS UPGRADES PROJECT Addendum No. 2 The following shall modify the Contract Documents. The work shall be accomplished in accordance with such modifications.

More information

UL / FM E-1 FIRE PROTECTION PRODUCTS INDICATOR POST FEATURES. *Applies to "ORDER LENGTH" codes B through F; code A has 22" adjustment.

UL / FM E-1 FIRE PROTECTION PRODUCTS INDICATOR POST FEATURES. *Applies to ORDER LENGTH codes B through F; code A has 22 adjustment. UL / FM MUELLER Indicator Post are used in fire protection systems and perform several functions. The Indicator Post provides a means to operate a buried or otherwise inaccessible valve. Also, the Indicator

More information

Mueller Gas Products. Mueller H17800 Curb Stop Tee No Blo Curb Stop Tee Weld x Weld 1440 PSI

Mueller Gas Products. Mueller H17800 Curb Stop Tee No Blo Curb Stop Tee Weld x Weld 1440 PSI Mueller Gas Products Distributed by: Mountain States Pipe and Supply Colorado Springs, Colorado 80903 1 800 777 7173 Mueller H17800 Curb Stop Tee No Blo Curb Stop Tee Weld x Weld 1440 PSI MUELLER NO-BLO

More information

Section COUPLINGS AND COUPLING ADAPTERS. This Section covers couplings and coupling adapters for ductile iron and steel pipe.

Section COUPLINGS AND COUPLING ADAPTERS. This Section covers couplings and coupling adapters for ductile iron and steel pipe. PART 1 GENERAL 1.01 SUMMARY Section 15155 This Section covers couplings and coupling adapters for ductile iron and steel pipe. 1.02 MEASUREMENT AND PAYMENT A. No separate payment for Work performed under

More information

PIPING NOMENCLATURE. Header Branch connection Valve Flange Expansion joint Expansion loop Pipe support Reducer Elbow

PIPING NOMENCLATURE. Header Branch connection Valve Flange Expansion joint Expansion loop Pipe support Reducer Elbow PIPING COMPONENTS Piping components are mechanical elements suitable for joining or assembly into pressure-tight fluid containing piping systems. Components include pipe, tubing, fittings, flanges, gaskets,

More information

Appendix E Part Details for the PT20 with Standard Bypass Valve

Appendix E Part Details for the PT20 with Standard Bypass Valve Appendix E Part Details for the PT0 with Standard Bypass Valve 8 ( ft lb) Part Number Locknut Wrench ( ft lb) 0 8 0 Note: The PT0 is shown below. All parts for the PT0 are the same except for the rotor

More information

AF-4 Grooved Flange Adapter

AF-4 Grooved Flange Adapter SUBMITTAL INFORMATION PROJECT NAME: ENGINEER: CONTRACTOR: SPEC. SECTION: MEMBER FEATURES & ADVANTAGES Designed for connecting ANSI/AWWA C110/A21.10 and ASME/ANSI B16.1 Class 125/ flanged end components

More information

5.1 MUELLER CORPORATION VALVES. MUELLER 300 Ball Type Corporation Valves

5.1 MUELLER CORPORATION VALVES. MUELLER 300 Ball Type Corporation Valves MUELLER CORPORATION VALVES 5.1 Shaded area indicates changes Rev. 4-14 Machine inserted corporation stops were developed by Hieronymus Mueller in conjunction with his development of the drilling and tapping

More information

Stock Programme Scope of Supply. v

Stock Programme Scope of Supply. v Scope of Supply v2.10 2018 Pipe: Seamless Stainless Steel ASTM A312 ASME B36.19 TP316/316L DN15 DN250 10S 160 Stainless Steel ASTM A312 ASME B36.19 TP304/304L DN15 DN200 10S 160 Low Temp ASTM A333 ASME

More information

FIRE PROTECTION PRODUCTS

FIRE PROTECTION PRODUCTS FEATURES Rev. 7-11 Mueller Indicator Post are used in fire protection systems and perform several functions. The Indicator Post provides a means to operate a buried or otherwise inaccessible valve. Also,

More information

5/16" Flange nut. Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc plated bolt w/ washers and nut. Anchor 3" sq. 7 Ga.

5/16 Flange nut. Bolt Keeper Plate (8 Sq. SYS.) (3) 1/2 x 3 Hex head connector zinc plated bolt w/ washers and nut. Anchor 3 sq. 7 Ga. 2 1/2" x 2 1/2" x 10 Ga. 6" 5" 4" Variable Slipbase (8" Sq. SYS.) 5/16 Corner Bolt W/ nut 5/16" Flange nut Stub Insert (8" Sq. SYS.) Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc

More information

General Information. Ball Curb Valve

General Information. Ball Curb Valve General Information 1. All Jones Curb Valves are manufactured in accordance with the AWWA Standard C-800-latest revision. 1. Copper Alloy CDA No. C83600 (85-5-5-5) 2. Copper Alloy CDA No. 89520 (Low Lead)

More information

I-VICFLEX.VS1. Victaulic VicFlex Style VS1 Dry Sprinkler WARNING WARNING TECHNICAL DATA BEND CHARACTERISTICS INSTALLATION INSTRUCTIONS SIDEWALL

I-VICFLEX.VS1. Victaulic VicFlex Style VS1 Dry Sprinkler WARNING WARNING TECHNICAL DATA BEND CHARACTERISTICS INSTALLATION INSTRUCTIONS SIDEWALL INSTALLATION INSTRUCTIONS I-VICFLEX.VS1 Victaulic VicFlex Style VS1 Dry Sprinkler SIDEWALL Y Read and understand all instructions before attempting to install any Victaulic VicFlex Style VS1 Dry Sprinklers.

More information

CHINA ZHEJIANG ZHONGGONG VALVE GROUP CO,.LTD FORMEN VALVE

CHINA ZHEJIANG ZHONGGONG VALVE GROUP CO,.LTD FORMEN VALVE INTERNATIONAL SALES: FORMEN VALVE ADD: OUBEI TOWN, YONGJIA COUNTY, WENZHOU, ZHEJIANG, CHINA HEADQUARTER: ZHEJIANG ZHONGGONG VALVE GROUP ADD: WUXING INDUSTRY ZONE, OUBEI TOWN, WENZHOU, CHINA ABOUT US Formen

More information

MEDIUM DUTY CAST IRON SLIDE GATES SERIES 20-10C

MEDIUM DUTY CAST IRON SLIDE GATES SERIES 20-10C MEDIUM DUTY CAST IRON SLIDE GATES SERIES 20-10C Revised October 2007 Armtec reserves the right to alter designs. General The Armtec Sluice Gate is a quality and highly economical gate for a variety of

More information

Pipe Restraints and Adapter Flanges. Section U. For PVC, Ductile Iron and Steel Pipe. 09/2017 Web Revision

Pipe Restraints and Adapter Flanges. Section U. For PVC, Ductile Iron and Steel Pipe. 09/2017 Web Revision DQS Inc. THE FORD METER BOX COMPANY, INC. CERTIFIED TO ISO 9001:2015 10004466 Section U 09/2017 Web Revision 11-29-17 Restraints and Adapter Flanges For PVC, Ductile Iron and Steel Contents Applications

More information

Annexure - V. Specifications, Typical Drawing & Data Sheet for Split TEE (Hot Tapping Material)

Annexure - V. Specifications, Typical Drawing & Data Sheet for Split TEE (Hot Tapping Material) Annexure - V Specifications, Typical Drawing & Data Sheet for Split TEE (Hot Tapping Material) CONTENTS SL NO. DESCRIPTION 1.0 SCOPE 2.0 REFERENCE DOCUMENTS 3.0 MANUFACTURER'S QUALIFICATION 4.0 MATERIALS

More information

W-K-M Model MA-1 DynaCentric Butterfly Valve

W-K-M Model MA-1 DynaCentric Butterfly Valve Page 1 of 16 R E P A I R M A N U A L W-K-M Model MA-1 DynaCentric Butterfly Valve Page 2 of 16 Published October 2001 W-K-M and DynaCentric are trademarks of Cooper Cameron Corporation Cooper Cameron Corporation,

More information

SECTION MANHOLES

SECTION MANHOLES SECTION 02601 MANHOLES PART 1 GENERAL 1.01 SCOPE OF WORK A. WORK required under this section consists of all materials, accessories, equipment, tools, and labor required to install precast concrete standard

More information

PART MATERIALS. Section Fencing Materials. Description

PART MATERIALS. Section Fencing Materials. Description PART 03000 - MATERIALS Section 03010 - Fencing Materials Description 03010.00 Scope - This section consists of the test requirements, specifications and tolerances for barbed wire, woven wire and chain

More information

Sample Specification

Sample Specification POWERS FASTENERS Sample Specification Section 22 10 xx Plumbing Piping The intent of this Sample Specification is to illustrate the use of ICC ES Acceptance Criteria as reference standards in the proper

More information

Kerkau Manufacturing. B16.5 Flange Book

Kerkau Manufacturing. B16.5 Flange Book Kerkau Manufacturing B16.5 Flange Book TABLE OF CONTENTS Revision 1 Title Page Table of Contents Tolerance Page Permissible Imperfections Dimensions of Flange Facings (all pressure rating classes) Dimensions

More information

DETAILED ENGINEERING OF PROCESS PIPING SYSTEMS

DETAILED ENGINEERING OF PROCESS PIPING SYSTEMS LAST UPDATED 25-10-2017 DETAILED ENGINEERING OF PROCESS PIPING SYSTEMS COURSE DURATION: 5 DAYS REACH US Today for Greater Safety, Quality, Reliability, Productivity, Profitability HRD Approved Class A

More information

SPECIFICATION STEEL COUPLING MODEL 411

SPECIFICATION STEEL COUPLING MODEL 411 Sleeve Bolt Nut Follower Gasket 1/2 2 TWO BOLT 3 12 HIGH STRENGTH 2 12 SMALL O.D. 14 60 LARGE O.D. APPLICATIONS Typical Uses Joining plain-end pipe of same outside diameters Replace split or excessively

More information

SECTION METAL FABRICATIONS

SECTION METAL FABRICATIONS SECTION 05100 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes specifications for metal fabrications, including minimum requirements for fabricator, and galvanizing. 1.02 REFERENCE STANDARDS A. ASTM

More information

SAMAMAT FLOW CONTROL L.L.C.

SAMAMAT FLOW CONTROL L.L.C. SAMAMAT FLOW CONTROL L.L.C. SFC-MK-LS-001 Rev.: 03 COMPANY PROFILE Company Location Company Information Company Size Nearest Transportation Company Name SAMAMAT FLOW CONTROL L.L.C Company Address Plot

More information

ADDENDUM NO. 1 TO THE CONTRACT DOCUMENTS AND SPECIFICATIONS DATED JULY 2017 FLORIDA GOVERNMENTAL UTILITY AUTHORITY PROJECT NO.

ADDENDUM NO. 1 TO THE CONTRACT DOCUMENTS AND SPECIFICATIONS DATED JULY 2017 FLORIDA GOVERNMENTAL UTILITY AUTHORITY PROJECT NO. ADDENDUM NO. 1 TO THE CONTRACT DOCUMENTS AND SPECIFICATIONS DATED JULY 2017 FLORIDA GOVERNMENTAL UTILITY AUTHORITY PROJECT NO. PS 061 SEVEN SPRINGS WASTEWATER TREATMENT FACILITY IMPROVEMENTS PASCO COUNTY,

More information

Fisher 1052 Size 20 Diaphragm Rotary Actuator with H Mounting Adaptation

Fisher 1052 Size 20 Diaphragm Rotary Actuator with H Mounting Adaptation Instruction Manual 1052 Size 20 Actuator (H) Fisher 1052 Size 20 Diaphragm Rotary Actuator with H Mounting Adaptation Contents Introduction... 1 Scope of Manual... 1 Description... 2 Specifications...

More information

SECTION DOMESTIC WATER AND SANITARY DRAINAGE PIPING PART 1 GENERAL

SECTION DOMESTIC WATER AND SANITARY DRAINAGE PIPING PART 1 GENERAL 15140.1 SECTION 15140 DOMESTIC WATER AND SANITARY DRAINAGE PIPING PART 1 GENERAL 1.1 SECTION INCLUDES A. Furnish and install sanitary drainage and vent piping systems, and domestic water piping, including

More information

PIP STF05121 Anchor Fabrication and Installation Into Concrete

PIP STF05121 Anchor Fabrication and Installation Into Concrete June 2017 Structural PIP STF05121 Anchor Fabrication and Installation Into Concrete PURPOSE AND USE OF PROCESS INDUSTRY PRACTICES In an effort to minimize the cost of process industry facilities, this

More information

SUBMITTAL INFORMATION "BOLTS, NUTS AND FLAT WASHERS" "ABSTRACT OF ASTM A307 GRADE A AND B" CARBON STEEL BOLTS AND STUDS, 60,000 PSI TENSILE STRENGTH

SUBMITTAL INFORMATION BOLTS, NUTS AND FLAT WASHERS ABSTRACT OF ASTM A307 GRADE A AND B CARBON STEEL BOLTS AND STUDS, 60,000 PSI TENSILE STRENGTH "BOLTS, NUTS AND FLAT WASHERS" "ABSTRACT OF ASTM A307 GRADE A AND B" CARBON STEEL BOLTS AND STUDS, 60,000 PSI TENSILE STRENGTH GRADE: LOW CARBON STEEL GRADE A GRADE B PHOSPHOROUS MAX % 0.06 0.04 SULFUR,

More information

How to Identify a PBM VALVE SERIES

How to Identify a PBM VALVE SERIES How to Identify a PBM VALVE SERIES Series 0 (SP, DP, MP) 1. If it is a manual valve, the handle generally would be made of a cast iron or cast bronze. 2. If it is a manual valve, the stem at the very top

More information

RELINER INSIDE DROP SYSTEM SPECIFICATIONS

RELINER INSIDE DROP SYSTEM SPECIFICATIONS 1. PRODUCT NAME RELINER INSIDE DROP SYSTEM U.S. Patent 6074130 Canadian Patent # 2269565 All RELINER Products are proudly made in the U.S.A. 2. MANUFACTURER RELINER /Duran Inc. 53 Mount Archer Rd. Lyme

More information

w w w.fastwell.in CATALOG NUMBER FFI -1005

w w w.fastwell.in CATALOG NUMBER FFI -1005 A trusted name in industrial valve company CATALOG NUMBER FFI -1005 Fastwell Fitting Industries is headquartered in Bakersfeld, California. We are a global manufacturer and supplier of valves to Oil &

More information

Fisher 667 Diaphragm Actuators Size 80 and 100

Fisher 667 Diaphragm Actuators Size 80 and 100 Instruction Manual 667 Size 80 and 100 Actuators Fisher 667 Diaphragm Actuators Size 80 and 100 Contents Introduction... 1 Scope of Manual... 1 Description... 2 Specifications... 2 Maximum Pressure Limitations...

More information

AUDAS. Tel: Fax: No.259 Baichi north Rd.Haiyan.Zhejiang.

AUDAS. Tel: Fax: No.259 Baichi north Rd.Haiyan.Zhejiang. Standard State SECTION A : SCREW THREAD Basic elements of screw thread design ANSI/ASME B1.7M Nomenclature.Definitions and letter symbols for screw thread ASME B1.1 Unified inch screw thread ( UN and UNF

More information

ANSI ORIFICE FLANGES METAL-KOREA

ANSI ORIFICE FLANGES METAL-KOREA METAL-KOREA ANSI ORIFICE FLANGES ORIFICE FLANGES are widely used in conjunction with orifice meters for measuring the rate of flow of liquids and gases. They are basically the same as standard welding

More information

Section Heavy Duty Slide Gates Tender No. [ ] Page 1

Section Heavy Duty Slide Gates Tender No. [ ] Page 1 Tender No. [ ] Page 1 1.0 GENERAL 1.1 REFERENCES.1 Provide heavy duty slide gates in accordance with the following standards (latest revision) except where specified otherwise..2 American Society for Testing

More information

Valves. Copyright 2007 Fluor Corporation. Lesson Objective. Lesson Objective. Introduction To Valves

Valves. Copyright 2007 Fluor Corporation. Lesson Objective. Lesson Objective. Introduction To Valves Copyright 2007 Fluor Corporation Valves Lesson Objective Lesson Objective Introduction To Valves Basic Types of Valves Flow Characteristics Gate Valve Relief Valve Globe Valve Horizontal Lift Check Valve

More information

OPERATION AND MAINTENANCE INSTRUCTIONS AVK UNDERGROUND FIRE HYDRANT

OPERATION AND MAINTENANCE INSTRUCTIONS AVK UNDERGROUND FIRE HYDRANT 1. INTRODUCTION Operation and maintenance manual for the series underground CLEARWAY fire hydrant 1 of 7 The designs, materials and specifications shown are subject to change without notice due to our

More information

REPUTE tube fittings are manufactured to stringent quality control program and internal standards which

REPUTE tube fittings are manufactured to stringent quality control program and internal standards which Introduction: REPUTE tube fittings are manufactured to stringent quality control program and internal standards which assure the highest quality available in the industry. Two ferrule tube fittings are

More information

ANDERSON GREENWOOD SAFETY SELECTOR VALVE

ANDERSON GREENWOOD SAFETY SELECTOR VALVE A dual pressure relief device system that provides a safe, efficient method of switching from an active PRV to a standby, maintaining system overpressure protection FEATURES GENERAL APPLICATION Safety

More information

Fluid Sealing Association

Fluid Sealing Association Fluid Sealing Association STANDARD FSA-MG-501-02 STANDARD TEST METHOD FOR INWARD BUCKLING OF SPIRAL-WOUND GASKETS 994 Old Eagle School Road, Suite 1019 Wayne, Pennsylvania 19087-1866 Phone: (610) 971-4850

More information

EN 1092 PN 10 EN 1092 PN 16 JIS B K ANSI B16.5 Class 150 ANSI B16.47 Class 150 BS 10 Table D

EN 1092 PN 10 EN 1092 PN 16 JIS B K ANSI B16.5 Class 150 ANSI B16.47 Class 150 BS 10 Table D HG EN 1092 PN 10 EN 1092 PN 16 JIS 2238 10K ANSI 16.5 Class 150 ANSI 16.47 Class 150 S 10 Table D Stafsjö s knife gate valve HG is a bi-directional valve, particularly well suited for severe operating

More information

SECTION FUEL OIL SYSTEM (PLUMBING)

SECTION FUEL OIL SYSTEM (PLUMBING) SECTION 15484 FUEL OIL SYSTEM (PLUMBING) PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 02221 - Excavating, Backfilling, and Compaction for Utilities. 2. 03300 - Cast-In-Place Concrete. 3. 15410 -

More information

Thru Wall Floor Seals For New Installation

Thru Wall Floor Seals For New Installation The O-Z/Gedney Thruwall and Floor Seals provide a positive means of sealing pipe, conduit or tube where they pass through a concrete foundation of a structure below grade or below ground water level or

More information

Lengths [7] Ø.50 [13] [7] [13]

Lengths [7] Ø.50 [13] [7] [13] Dimensions in [ ] are in millimeters Standard (2 1 / 2 6 ) Standard (9 24 ).75 STEM.40 [10] EXTERNAL THREAD.61 [15] 1.00 [25] STEM STEM Ø.44 [11] Threaded-Stepped Shank Standard Stem Length Length (T)

More information

11-1/4 OD at Transition Point. Microcosmic. 4th and Brannan Street Platform Station Project. Elevation. Moto Ohtake 2014

11-1/4 OD at Transition Point. Microcosmic. 4th and Brannan Street Platform Station Project. Elevation. Moto Ohtake 2014 74 480 330 90 72 180 150 60 90 18 11- OD at Transition Point 36 184 74 Microcosmic Elevation 14 1 Moto Ohtake I. GENERAL NOTES: A. SCULPTURE DESIGN CRITERIA 1. CALIFORNIA BUILDING CODE (CBC, 2010 EDITION)

More information

Ford Water Meter Couplings & Accessories

Ford Water Meter Couplings & Accessories Section H 2/2001 Ford Water Meter Couplings & Accessories The Ford Meter Box Co., Inc. 775 Manchester Avenue, P.O. Box 443, Wabash, Indiana, USA 46992-0443 Telephone: 260/563-3171 FAX: 1-800-826-3487 Overseas

More information

Bronze Ball Valves. Ball-Grooved Box Qty. 1 1 Above with 2 internal Case Qty. 4 4 Supervisory Switches Unit Weight

Bronze Ball Valves. Ball-Grooved Box Qty. 1 1 Above with 2 internal Case Qty. 4 4 Supervisory Switches Unit Weight FIRE PROTECTION VALVES FPP-0118 Effective January 1, 2018 Supercedes FPP-0717 of July 24, 2017 Prices and MTO status subject to change without notice. Visit our website for the most current information.

More information

SIGHT GLASS. Sight glass components allow operators to safely observe processes inside tanks, pipes, reactors and vessels.

SIGHT GLASS. Sight glass components allow operators to safely observe processes inside tanks, pipes, reactors and vessels. SIGHT GLASS Sight glass components allow operators to safely observe processes inside tanks, pipes, reactors and vessels. SIGHT GLASS Sight flow indicator. A sight flow indicator is used in process pipelines

More information

NAVSEA STANDARD ITEM

NAVSEA STANDARD ITEM NAVSEA STANDARD ITEM FY-19 DATE: 01 OCT 2017 CATEGORY: I 1. SCOPE: 1.1 Title: Threaded Fastener Requirements; accomplish 2. REFERENCES: 2.1 Standard Items 2.2 S9086-CJ-STM-010/075, Fasteners 3. REQUIREMENTS:

More information

Hex Cap Screws Coarse & Fine Thread

Hex Cap Screws Coarse & Fine Thread INDUSTRIAL Product Description Hex head cap screws are manufactured to dimensional standards of ASME B18.2.1 and to various material and mechanical standards of ASTM and SAE. The length of a cap screw

More information

bronze ball valves Ball-Grooved Box Qty. 1 1 Above with 2 internal Case Qty. 4 4 Supervisory Switches Unit Weight

bronze ball valves Ball-Grooved Box Qty. 1 1 Above with 2 internal Case Qty. 4 4 Supervisory Switches Unit Weight fire protection valves FPP-0312 Effective March 26, 2012 Supercedes FPP-0611 of June 1, 2011 Prices and MTO status subject to change without notice. Visit our website for the most current information.

More information

Midwest Roadside Safety Facility

Midwest Roadside Safety Facility B 64" 1626 602'-8 1/16" 183695 548'-0" 167030 1 2 3 4 5 6 7 8 9 10 11 12 14 15 16 17 18 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 373839 40 25 IMPACT 1500A 48" 12 27'-5" 8355 [] 3x7 CL A Galvanized

More information

Bronze Ball Valves. Ball-Grooved Box Qty. 1 1 Above with 2 internal Case Qty. 4 4 Supervisory Switches Unit Weight

Bronze Ball Valves. Ball-Grooved Box Qty. 1 1 Above with 2 internal Case Qty. 4 4 Supervisory Switches Unit Weight FIRE PROTECTION VALVES FPP-0115 Effective January 19, 2015 Supercedes FPP-0114 of January 6, 2014 Prices and MTO status subject to change without notice. Visit our website for the most current information.

More information

METAL FABRICATION SECTION 8: METAL FABRICATION SCOPE MATERIAL.

METAL FABRICATION SECTION 8: METAL FABRICATION SCOPE MATERIAL. METAL FABRICATION SCOPE This specification applies to all metal intended to be rubber lined. Metals furnished must conform to this specification with respect to suitability for rubber lining or covering.

More information

General Information...SA1-SA4

General Information...SA1-SA4 SECTION S INDEX Product Description Page Number General Information................................................................SA1-SA4 Type FSK Thruwall & Floor Seal For Conduit, Pipe or Tubing............................

More information

VALVTECHNOLOGIES, INC. INSTALLATION, OPERATIONS & MAINTENANCE MANUAL STEAM CHOKE VALVES

VALVTECHNOLOGIES, INC. INSTALLATION, OPERATIONS & MAINTENANCE MANUAL STEAM CHOKE VALVES VALVTECHNOLOGIES, INC. INSTALLATION, OPERATIONS & MAINTENANCE MANUAL STEAM CHOKE VALVES Page STEAM CHOKE VALVES The Valvtechnologies steam choke is designed for the harsh conditions associated with steam

More information

CATALOG FOR PRESSURE CONTROL EQUIPMENT. Supplement 3 API CONNECTOR ACCESSORIES. Ring Gaskets, Flange Bolts and Nuts, Hammer Wrenches TRADEMARK WOODCO

CATALOG FOR PRESSURE CONTROL EQUIPMENT. Supplement 3 API CONNECTOR ACCESSORIES. Ring Gaskets, Flange Bolts and Nuts, Hammer Wrenches TRADEMARK WOODCO CATALOG FOR PRESSURE CONTROL EQUIPMENT Supplement 3 API CONNECTOR ACCESSORIES Gaskets, Flange Bolts and Nuts, Hammer Wrenches This catalog supplement provides information to allow selection and accurate

More information

SPECIFICATION: ALUMINUM SLIDE GATES

SPECIFICATION: ALUMINUM SLIDE GATES SPECIFICATION: ALUMINUM SLIDE GATES PART 1 GENERAL 1.1 The Slide gates shall be manufactured from Aluminum material as specified and shall be Flange back type suitable for wall thimble mounting and generally

More information

1.1 SUMMARY. A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards.

1.1 SUMMARY. A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards. PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards. B. See Division 5 Section "Pipe and Tube Railings"

More information

Stepping ahead in technology & innovation PIPING INSTITUTE OF TECHNOLOGY & ANALYSIS SOLUTIONS

Stepping ahead in technology & innovation PIPING INSTITUTE OF TECHNOLOGY & ANALYSIS SOLUTIONS Stepping ahead in technology & innovation PIPING INSTITUTE OF TECHNOLOGY & ANALYSIS SOLUTIONS PIPING ENGINEERING & PLANT DESIGN Chapter 1. Introduction of Piping Industry & Role of Piping Engineer 1.1.

More information

Engineering Data Single Reduction Parts List Item # Description Basic Single Reduction Unit 1. Gear Housing 2. Pipe Plug 3. Vent Plug 4. Splash Guard

Engineering Data Single Reduction Parts List Item # Description Basic Single Reduction Unit 1. Gear Housing 2. Pipe Plug 3. Vent Plug 4. Splash Guard Engineering Data Single Reduction Parts List Item # Description Basic Single Reduction Unit 1. Gear Housing 2. Pipe Plug 3. Vent Plug 4. Splash Guard 5. Input Cover 6. O-Ring 7. Hex Head Cap Screw 8. Input

More information

FOR BIS USE ONLY Doc. No. PG 28(1144) August 2008

FOR BIS USE ONLY Doc. No. PG 28(1144) August 2008 FOR BIS USE ONLY Doc. No. PG 28(1144) August 2008 PRELIMINARY DRAFT AMENDMENT NO.2 AUGUST 2008 TO IS 13136 : 1991 ARMS AND AMMUNITION RIFLE AIR RIFLE SPRING OPERATED SPECIFICATION [ Pag12,Annex A ] Substitute

More information

Air Hose Products.

Air Hose Products. Air Hose Products 1.1 Bulk Red Air Hose 1.2 Jackhammer Hose Assemblies 1.3 Air Tool Hose Assemblies 1.4 Hot Air Blower Hose 1.5 Yellow Wire Braid Air Hose Assemblies and Fittings 1.6 Air Hose Fittings

More information

Repair Manual 12 PL PILOT

Repair Manual 12 PL PILOT Repair Manual 12 PL PILOT 12 PL PILOT REPAIR MANUAL INDEX Introduction... 1 Elastomer Materials... 2 Disassembly... 3 Assembly... 7 Testing... 11 NOTE: We reserve the right to modify or change, without

More information

UII Pump Parts

UII Pump Parts 0-4-0-4-UII Pump Parts. Page 66 95-0305 September 009 Parts Lists 0-4-0-4-UII Pump Parts QTY. PER PUMP PART NOTES 0-U Pump Body See Note 0-U Pump Body with Flush See Note 4-U Pump Body See Note 4-U Pump

More information

1.0 SCOPE DEFINITIONS CODES AND STANDARDS GENERAL MATERIAL SPECIFICATIONS... 9

1.0 SCOPE DEFINITIONS CODES AND STANDARDS GENERAL MATERIAL SPECIFICATIONS... 9 TABLE OF CONTENTS 1.0 SCOPE... 6 1.1 DEFINITIONS... 6 1.2 CODES AND STANDARDS... 6 2.0 GENERAL MATERIAL SPECIFICATIONS... 9 2.1 CARBON STEEL PIPING CLASSES 15, 15H, 15U, 30U, 30, 30W, 30H (NOTE1)... 9

More information

UNIFIED FACILITIES GUIDE SPECIFICATIONS

UNIFIED FACILITIES GUIDE SPECIFICATIONS USACE / NAVFAC / AFCESA / NASA UFGS-33 34 13 (April 2008) -------------------------- Preparing Activity: USACE Superseding UFGS-33 34 13 (April 2006) UNIFIED FACILITIES GUIDE SPECIFICATIONS References

More information

Ground Clamps Cable Tray

Ground Clamps Cable Tray commercial and industrial fittings: ing Fittings and Solderless Connectors Clamps Cable Tray Terminates ground wire to cable tray. For aluminum or copper conductors. 1 4 hex wrench tightens both tray and

More information

Reliance SG800 Series Steel Water Gage Valves

Reliance SG800 Series Steel Water Gage Valves Installation, Operation, & Maintenance Instructions R500.541D1 10/16/2016 Reliance SG800 Series Steel Water Gage Valves Note: Design variations in Steel Water Gage Valves necessitate typical illustrations,

More information

A Full Line of Pipe Products for Any Application

A Full Line of Pipe Products for Any Application Standard Pipe SureThread and ERW: Setting the standard in the standard pipe industry With a tradition of service and quality that s 80-plus years strong, Wheatland Tube is the only domestic, full-line

More information

Installation Tools. Pipe Cutters for steel and cast iron pipes 598. Deburring Reamer / for stainless steel pipes 600. for copper pipes 602

Installation Tools. Pipe Cutters for steel and cast iron pipes 598. Deburring Reamer / for stainless steel pipes 600. for copper pipes 602 596 597 Installation Tools Pipe Cutters for steel and cast iron pipes 598 Pipe Cutters / Pipe Deburring Reamer for stainless steel pipes 600 Pipe Cutters / Pipe Deburring Reamer / Calibrating Tool for

More information

Rodney Hunt. A GA Industries Company Glydaseal Gates

Rodney Hunt. A GA Industries Company Glydaseal Gates Rodney Hunt A GA Industries Company Glydaseal Gates GUIDE BRONZE GUIDE BAR FRAME NUT POCKET SEAT FACING RESILIENT INVERT SEAT DISC GUIDE BAR ADJUSTMENT BOLT WITH LOCK NUT GUIDE BAR ATTACHING BOLT The Glydaseal

More information

Fitting C.O. Adapter

Fitting C.O. Adapter ABS-DWV Fittings ABS/DWV Service Weight Pipe Schedule 30 Single step solvent cementing procedures no primer required. Excellent solvent cementing characteristics. Black. 84/Ctn. x h Hub Sanitary 0321612

More information

25000 Series Lo-T TM Butterfly Control Valve Instructions

25000 Series Lo-T TM Butterfly Control Valve Instructions November 2001 25000 Series Lo-T TM Butterfly Control Valve Instructions Instruction No. 25.1:IM PRELIMINARY STEPS Before installation, note the flow direction arrow on the valve body. The flow should enter

More information

FNW can handle all your hanger and fastener needs, all in one place. FNW products are sold exclusively at Ferguson.

FNW can handle all your hanger and fastener needs, all in one place. FNW products are sold exclusively at Ferguson. FASTENERS PIPE HANGERS, SUPPORTS & STRUT ACCESSORIES FNW can handle all your hanger and fastener needs, all in one place. FNW products are sold exclusively at Ferguson. Quick Reference Nuts Heavy Hex Nuts...4

More information

Testing. Material testing will be according to applicable AASHTO, ASTM or Department methods as specified.

Testing. Material testing will be according to applicable AASHTO, ASTM or Department methods as specified. 907.01 Section 907. FENCING MATERIALS 907.01 General Requirements. Materials for use in fencing property, right-of-way and other installations must comply with this section. 907.02 Testing. Material testing

More information

Swivel Hoist Ring RIGGING ACCESSORIES. Color coded to distinguish between UNC (Red) and Metric (Silver) thread types.

Swivel Hoist Ring RIGGING ACCESSORIES. Color coded to distinguish between UNC (Red) and Metric (Silver) thread types. RIGGING ACCESSORIES Color coded to distinguish between UNC (Red) and Metric (Silver) thread types. Available in UNC and Metric thread sizes. UNC threads available in sizes from 800 pounds to 100,000 pounds,

More information