Section 13. Toroids. Parylene C is a trademark of Union-Carbide Corp. Material R P F J W H. Color Blue Green White Red Yellow Purple 13.
|
|
- Bartholomew Atkinson
- 5 years ago
- Views:
Transcription
1 Section 13. Toroids Ferrite toroids offer high magnetic efficiency as there is no air gap, and the cross sectional area is uniform. vailable in many sizes ( s from.100" to 3.375"), and materials (permeabilities from 750 to 15,000), this section lists the common ones used in the industry. For other sizes, contact the factory. HIGH PERMEBILITY PPLICTIONS. High inductance, high impedance over wide frequency ranges and low loss factor make J, W and H toroids excellent choices for common mode chokes, broadband transformers, pulse transformers and current transformers. POWER PPLICTIONS. Low losses, high B sat, minimum losses at high temperature and high Curie temperature make R, P, K, and F toroids excellent choices for high frequency transformers. GFI PPLICTIONS. Special sizes in J and B materials are available for ground fault interrupter applications. B is a 5000µ material and has a minimum permeability of 4000 over a temperature range of -35 C to +70 C. COTINGS In order to increase winding ease and improve voltage breakdown, the cores can be coated. 1. Parylene C. This vacuum-deposited material has a uniform coating (including edges) with a thickness of.0005" to.002", a smooth winding surface, and good moisture resistance to organic solvents and acid bases. The electrical characteristics are superior to other coatings. It is available in s up to.500. Continuous maximum rating is 130 C. (Minimum inductance 5% lower that listed.) For Parylene, add Y to part number. 2. Grey coating. This inexpensive coating is typically.004" to.008" thick, provides good adhesion, smooth winding surface, and good resistance to moisture and organic solvents. Good for continuous operation from -65 C to +155 C, this coating is available in sizes.375" and larger. See Specifying coating below. For grey coating, add Z to part number. VOLTGE BREKDOWNS The following are voltage breakdowns for the above coatings (wire to wire). See page 3.1, how measured. Parylene C: 600 volts min. (Minimum inductance 5% lower than listed) Grey coating: 1000 volts min. SPECIL REQUIREMENTS Color coding. Toroids (and other cores) can be marked with a color code to distinguish different materials. When ordering, add -CC at the end of the part number. Codes are: Material R P F J W H Color Blue Green White Red Yellow Purple High Voltage. Voltage breakdown, higher than the standard guarantee, can be provided. Dimensional tolerances are relaxed to allow for the added coating. Contact the factory for a special specification. Specifying coating. Grey coating may be polyester or nylon, in order to minimize cost. Polyester is rated to 200 C. Nylon exhibits outstanding solvent resistance. Nylon is available only in sizes to as listed in this catalog. Within this range, add -PO at the end of the part number to specify polyester only or add -NO at the end of the part number to specify nylon only. Parylene C is a trademark of Union-Carbide Corp. 13.1
2 TORIOD DT (Contact Factory for other available sizes) available coatings 13.2 NO. (OD) MECHNICL DIMENSIONS (Note 1 P13.3) FOR PREFERRED S, SEE INSIDE BCK COVER (2) L (mh/1000 TURNS) INCHES MILLIMETERS POWER MTERILS TELECOM MTERILS B (ID) C HGT. (2) (OD) TC ,360 5,830 7, TC ,700 4,030 B (ID) C HGT. K 1500µ ±25% R 2300µ ±25% P 2500µ ±25% F 3000µ ±20% TC TC TC TC TC TC , TC TC ,020 1, TC ,920 2,088 2, ,670 1, TC ,730 1,884 2, ,510 1, TC ,000 1,095 1, , TC ,510 1,650 1, ,315 1, TC ,600 2,820 3, ,255 2, TC TC ,090 1,190 1, , TC ,360 1,485 1, ,188 1, TC ,080 1,660 1,805 2, ,444 1, TC ,240 1,356 1, ,085 1, TC ,020 1,111 1, , TC ,040 1,130 1, , TC ,080 1, TC ,260 1,375 1, ,100 1, TC ,830 2,810 3,050 3, ,440 2, TC ,380 1,500 1, ,200 1, TC ,260 1,930 2,100 2, ,680 1, TC ,380 1,510 1, ,208 1, TC ,120 1,720 1,875 2, ,500 1, TC ,810 2,770 3,020 3, ,416 2, TC ,170 1,800 1,958 2, ,565 1, TC ,450 2,220 2,420 2, ,930 2, TC ,450 1,585 1, ,268 1, TC ,930 2,960 3,222 3, ,579 2, TC ,860 2,850 3,100 3, ,480 2, TC ,480 1,610 1, ,290 1, TC ,030 2,210 2, ,770 2, TC ,100 3,366 4,040 1,011 2,696 3, TC ,020 2,200 2, ,760 2, TC ,850 4,185 5,020 1,255 3,345 3, TC ,060 8,762 10, TC ,710 2,950 3, TC ,790 3,032 3, TC ,420 3,718 4, TC ,430 5,900 7, TC ,140 3,491 4, TC ,770 6,270 7, TC ,700 4,024 4, TC ,510 2,726 3,310 4, µ ±20% D 200µ ±20% G 2300µ ±20% L values based on 5 gauss in a de-gaussed state.
3 L (mh/1000 TURNS) HIGH PERMEBILITY MGNETIC DIMENSIONS MTERILS J W H WINDOW CORE Wac 5000µ 10,000 µ 15,000µ WGT. NO. ± 20% ± 30% ± 30% Ie e Ve RE (Note 3) (gms) (cm) (cm²) (cm³) (cm²) (cm 4) TC 875 1,750 2, TC 825 1,650 2, TC 735 1,470 2, TC 1,475 2,950 4, TC 950 1,900 2, TC 1,900 3,800 5, TC 980 1,960 2, TC 2,040 4,080 6, TC 4,175 8,350 12, TC 3,765 7,530 11, TC 2,196 4,392 6, TC 3,308 6,616 9, TC 5,640 11,280 16, TC 1,488 2,976 4, TC 2,380 4,760 7, TC 2,968 5,936 8, TC 3,612 7,224 10, TC 2,715 5,430 8, TC 2,295 4,590 6, TC 2,260 4,520 6, TC 2,160 4,320 6, TC 2,760 5,520 8, TC 6,115 12,200 18, TC 2,800 5,600 8, TC 4,200 8,400 12, TC 3,020 6,040 9, TC 3,700 7,400 11, TC 6,040 12,080 18, TC 3,913 7,825 11, TC 4,830 9,660 14, TC 3,170 6,340 9, TC 6,447 12,894 19, TC 6,200 12, TC 3,220 6, TC 4,543 9, TC 6,736 13, TC 4,400 8, TC 8,365 16, TC 16,730 33, TC 11,600 23, TC 8,075 16, TC 5,900 11, TC 6,065 12, TC 7,435 14, TC 11,800 23, TC 6,845 13, TC 12,500 25, TC 8,140 16, TC 5,520 11, TO ORDER TOROIDS (a) dd the material designationletter before the part number (e.g., F TC). (b) For Parylene coated cores, add Y to part number (YF TC). For grey coated cores, add Z to part number (ZF TC). (c) 0 in part number = bare core (0F TC). (d) Suffixes for the following requirements may be added as shown: CC= core Color Coded PO= Polyester Only toroid coating NO= Nylon Only toroid coating For example, ZF TC-PO FOR PREFERRED S, SEE INSIDE BCK COVER NOTES 1. For the cores listed here, dimensional tolerances for bare and coated cores are on pages Page 13.6 also lists guidelines for dimensional tolerances of all toroids. 2. Other core heights are available on special request. 3. Product of window area and core area. 13.3
4 Ferrite Toroids (Bare Core) Limiting Dimensions Inches Millimeters Materials other than W and H W and H Materials Materials other than W and H W and H Materials NO TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC
5 Ferrite Toroids (Z Coated) Limiting Dimensions Inches Millimeters Materials other than W and H W and H Materials Materials other than W and H W and H Materials NO TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC See page 13.6 for Y coated cores 13.5
6 Ferrite Toroids (Y Coated) Limiting Dimensions Inches Millimeters Materials other than W and H W and H Materials Materials other than W and H W and H Materials NO TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC TC FOR THESE CORE OD'S up to.099".100" -.199".200" -.299".300" -.599".600" -.999" 1.000" " 1.500" " 2.000" " 2.500" " 3.000" " DIMENSIONL TOLERNCE GUIDELINES OD and ID TOLERNCES FOR HEIGHT TOLERNCES (1)(2) RE THESE RE CORE Mat'ls other than W&H HEIGHTS Mat'ls other than W&H W&H Mat'ls W&H Mat'ls ±.005" ±.005" Up to.099" ±.003" ±.007" ±.008" ±.008".100" -.199" ±.005" ±.010" ±.011" ±.011".200" -.299" ±.007" ±.011" ±.010" ±.015".300" -.599" ±.010" ±.015" ±.015" ±.023".600" -.999" ±.015" ±.023" ±.020" ±.030" 1.000" " ±.020" ±.030" ±.030" ±.045" 1.500" " ±.030" ±.045" ±.035" ±.053" (1) For W and H material cores 2.8" and larger in OD, ±.040" ±.060" add 50% to height tolerance. ±.050" ±.075" (2) For cores <.300" OD, use W & H column. FOR COTED CORES: COTING SIZE LIMITS: llow.003" for Y finish. Parylene(Y) and smaller llow.015" for Z finish. (Minimum inductance 5% lower than listed) llow.030" for voltages above 1000 up to Grey (Z) and larger 13.6
7 Toroid Mounts These vertical mount accessories are designed to accommodate a variety of toroidal core sizes on to printed circuit board or other assemblies. (Check factory for new parts not shown here) TV-B For use with P/N s 41206TC TC or toroid sizes with an =.500" -.870" TV-B2908-T For use with P/N s 42507TC TC or toroid sizes with an =.81" TV-B3610-F For use with P/N s 42908TC TC or toroid sizes with an = 1.142" " Material: Phenolic UL 94 VO rated Pin Material: CP Wire Pin Diameter:.039" DIMENSIONS (IN.) NUMBER TV-B (6 pins) TV-B2908-T (10 pins) TV-B3610-F (14 pins) NOM B NOM C REF D NOM E REF F TYP G TYP G H NOM J REF K REF G
8 Toroid Mounts FIGURE 1 For use with core sizes (outside diameter) from.50" to 1.00" Material: Nylon UL 94 VO Rated Pin Material: CP Wire Pin Diameter:.040" FIGURE 2 For use with core sizes (outside diameter) from.81" to 2.8" Material: Nylon UL 94 VO Rated Pin Material: CP Wire Pin Diameter:.050" DIMENSIONS (IN.) (NOM.) NUMBER FIG. B C E F G H J For Core TV-H TV-H TV-H TV-H TV-H " ".81" " 1.25" " 1.5" - 2.5" 1.9" - 2.8" SURFCE MOUNT HEDERS Several surface mount headers are available. See pages 6.6, 6.9 and 6.12 for sizes and dimensions. 13.8
9 Toroid Cups and Headers Figure 1 Material: L.C.P. Figure 2 Material: Phenolic Figure 3 Material: Phenolic Figure 4 Material: L.C.P. ll parts - UL 94 V-O rated Pin Materials - Phosphor bronze DIMENSIONS IN INCHES B C D E F G H J K L M For Core NUMBER FIG. MX. MX. NOM. TYP. NOM. MX. MIN. NOM. MIN. MX. NOM. MIN. SM-C <.155 SM-C <.250 SM-H <.200 SM-H <
Section 13. Toroids COATINGS
Section 13. Toroids Ferrite toroids offer high magnetic efficiency as there is no air gap, and the cross sectional area is uniform. Available in many sizes ('s from.100" to 3.375") and materials (permeabilities
More informationSection Toroids COATING CODE (SEE PG 13.2) FERRITE CORE MATERIAL TYPE USED FOR ALL FERRITE TYPES APPROXIMATE DIAMETER IN MM
TOROIDS Ferrite toroids offer high magnetic efficiency as there is no air gap, and the cross sectional area is uniform. Available in many sizes (s from 2.54mm to 107mm) and materials (permeabilities ranging
More informationFERRITE CORES 2012 CATALOG
FERRITE CORES 2012 CATALOG Part Number Index TOROIDS E CORES SHAPES TOROID PG TOROID PG 40200TC 16 43610TC 20 40301TC 16 43615TC 20 40401TC 16 43620TC 20 40402TC 16 43806TC 20 40502TC 16 43813TC 20 40503TC
More information-Thermo-set plastic coated parts can withstand a minimum breakdown voltage of 1000 Vrms, uniformly applied across the 'C' dimension of the toroid.
Fair-Rite Product's Catalog Fair-Rite Products Corp. PO Box J,One Commercial Row, Wallkill, NY 12589-0288 Part Number: 5977011101 Frequency Range: Medium Permeability, 77 (ui=2000) & 78 (ui=2300) materials
More information-Thermo-set plastic coated parts can withstand a minimum breakdown voltage of 1000 Vrms, uniformly applied across the 'C' dimension of the toroid.
Part Number: 5978014001 Frequency Range: Medium Permeability, 77 (ui=2000) & 78 (ui=2300) materials Description: Application: Where Used: Part Type: 78 TOROID Inductive Components Closed Magnetic Circuit
More information-Thermo-set plastic coated parts can withstand a minimum breakdown voltage of 1000 Vrms, uniformly applied across the 'C' dimension of the toroid.
Part Number: 5967001701 Frequency Range: Low Permeability, 67 (ui=40) material Description: Application: Where Used: Part Type: 67 TOROID Inductive Components Closed Magnetic Circuit Toroids Mechanical
More informationDesign Considerations
Design Considerations Ferrite beads provide a simple, economical method for attenuating high frequency noise or oscillations. By slipping a bead over a wire, a RF choke or suppressor is produced which
More informationDesign Considerations
Design Considerations Ferrite toroids provide an often convenient and very effective shape for many wide band, pulse and power transformers and inductors. The continuous magnetic path yields the highest
More informationA3134. Discontinued Product
3134 Bipolar Hall Effect Switch for High-Temperature Operation Discontinued Product These parts are no longer in production The device should not be purchased for new design applications. Samples are no
More informationExperience the Power of Confidence
Experience the Power of Confidence the confidence of over fifty years of expertise in the research, design, manufacture and support of high quality magnetic materials and components. A major supplier of
More informationTOROID : FT,T & BALUN
TOROID : FT,T & BALUN By N.S. Harisankar - VU3NSH. Phone : (0491) 2576102 The Toroidal cores are grouped into two types. (a) powdered Iron and (b) Ferrites. The Ferrite materials are based on "Nickel-Zinc"
More informationA3132 and A3133. Ultrasensitive Bipolar Hall Effect Switches. Discontinued Product
3132 and 3133 Ultrasensitive Bipolar Hall Effect Switches Discontinued Product These parts are no longer in production The device should not be purchased for new design applications. Samples are no longer
More informationTOROIDAL CORES : IRON POWDER CORES
1 von 19 19.07.2007 08:49 TOROIDAL CORES : IRON POWDER CORES Iron Powder Cores are made in numerous shapes and sizes: such as Toroidal Cores, E- cores, Shielded Coil Forms, Sleeves etc., each of which
More informationPOWDER CORES. Molypermalloy High Flux Kool Mµ XFlux Kool Mµ MAX
POWDER CORES Molypermalloy High Flux Kool Mµ XFlux Kool Mµ MAX We offer the confidence of over sixty years of expertise in the research, design, manufacture and support of high quality magnetic materials
More informationRhombus Industries Inc.
NEW! FOR '97 MAGNETIC COMPONENTS INDUCTORS, COILS & SMPS MAGNETICS PRODUCTS INCLUDE... CURRENT SENSE POWER LINE CHOKES HASH CHOKES COMMON MODE MAG AMP TOROIDS POWER INDUCTORS SWING INDUCTORS HIGH L AIR
More informationPowder Cores. Molypermalloy High Flux
Powder Cores Molypermalloy High Flux Kool Mµ Since 1949, MAGNETICS, a division of Spang & Company, has been a leading world supplier of precision, high quality, magnetic components and materials to the
More informationSMALLER-FASTER- OW R CO$T
SMALLER-FASTER- OW R CO$T Magnetic Materials for Today s High-Power Fast-Paced Designs Donna Kepcia Technical Sales Manager Magnetics DISCUSSION OVERVIEW Semiconductor Materials, SiC, Silicon Carbide &
More informationA3503. Ratiometric Linear Hall Effect Sensors. Discontinued Product
3503 Ratiometric Linear Hall Effect Sensors Discontinued Product These parts are no longer in production The device should not be purchased for new design applications. Samples are no longer available.
More informationSolving Electromagnetic Interference (EMI) with Ferrites
Solving Electromagnetic Interference (EMI) with Ferrites What are ferrites? How do ferrites help Suppress EMI? How to chose proper ferrite and component Material Characteristics Material and Core Selection
More informationIron Powder Core Selection For RF Power Applications. Jim Cox Micrometals, Inc. Anaheim, CA
HOME APPLICATION NOTES Iron Powder Core Selection For RF Power Applications Jim Cox Micrometals, Inc. Anaheim, CA Purpose: The purpose of this article is to present new information that will allow the
More information3D COIL 15x15 10mH ±5% 125 KHz SMD DROP RESISTANT TRANSPONDER 3D COIL 15.9x15.9 mm
1/7 3D COIL 15x15 10mH ±5% 125 KHz SMD DROP RESISTANT TRANSPONDER 3D COIL 15.9x15.9 mm Made by: Sergio Cobos Checked by: S. Cobos Approved by: F. Bustos Date: 20/02/12 Date: 20/02/12 Date: 12/03/2012 Signature:
More information8 to 32 AWG Solid Round Copper ranges from to ranges from to C. Polyester/Polyamideimide
Gauge: Conductor: Pounds per 1000 feet: Feet per pound: Insulation Temp. Rating: Enamel Type: Enamel Build: Average Wire Diameter: Manufacturer: Product Line: Color: Solder Process: Approvals: Applications:
More informationSMALLER-FASTER- OW R CO$T
SMALLER-FASTER- OW R CO$T Magnetic Materials for Today s High-Power Fast-Paced Designs Donna Kepcia Technical Sales Manager Magnetics DISCUSSION OVERVIEW Semiconductor Materials, SiC, Silicon Carbide &
More information(1)Core shape UF: U-type core. Inductance value Rated current Handling power Weight Minimum package quantity
(/) 00-0 / 0050805 / e9_tf.fm TDK common mode choke coils(line filters) are used in a wide range of prevention of electromagnetic interference(emi) and radio frequency interference(rfi) from power supply
More informationCOPPER MAGNET WIRE GP/MR C
COPPER MAGNET WIRE SPECIFICATIONS Gauge: 8 to 32 AWG Conductor: Solid Round Copper Pounds per 1000 feet: ranges from 20.02 to 0.3192 Feet per pound: ranges from 49.95 to 3132 Insulation Temp. Rating: 200
More informationMAGNETIC POWDER CORES
Ver.13 www.changsung.com MAGNETIC POWDER CORES Innovative Technological Advancements Move forward with Chang Sung Corporation. We are one of the main suppliers of cutting edge products to all our customers
More informationMEASURING TRANSFORMER DISTRIBUTED CAPACITANCE. Kirby Creel, Engineering Manager, Datatronics
By Kirby Creel, Engineering Manager, Datatronics This article is a general discussion of distributed capacitance, Cd, in transformers with emphasis on measurement. We will discuss how capacitance occurs,
More informationEMC Components. HF Series Common-Mode Choke Coils for AC Power Supply Closed Magnetic Circuit, High Impedance
(/5) FEATURES Comprising double-square closed magnetic circuit ferrite cores and windings on partitioned bobbins, these common-mode choke coils are useful for noise suppression. With the small size and
More informationExperience the Power of Confidence
Experience the Power of Confidence the confidence of over fifty years of expertise in the research, design, manufacture and support of high quality magnetic materials and components. A leading manufacturer
More informationEMI Suppression Beads
24 Fair-Rite offers a broad selection of EMI suppression beads with guaranteed impedance specifications over a wide frequency range. Beads with a 1 as the last digit of the part number are not burnished,
More informationFair-Rite offers a broad selection of ferrite EMI suppression beads with guaranteed minimum impedance specifications.
Part Number: 2661000301 Frequency Range: Higher Frequencies 250-1000 MHz (61 material) Description: Application: Where Used: Part Type: Preferred Part: 61 SHIELD BEAD Suppression Components Board Component
More informationDry Type Transformers Full Line Catalog. jeffersonelectric.com
Dry Type Transformers Full Line Catalog jeffersonelectric.com The Transformer Authority PIONEER TRANSFORMERS: Why us? Scale We produce over 100,000 transformers every year. With this high level of production
More informationLooking for magnetic parts? Low Permeability Nanocrystalline Cores Nanophy. Material on design Permeability on demand
Looking for magnetic parts? kµ cores Low Permeability Nanocrystalline Cores Nanophy Stainless & Nickel Alloys Components Material on design Permeability on demand Permeability range from 2 to 3 Material
More informationMAX485 Low Power, Slew-Rate-Limited RS-485/RS-422 Transceiver
MX485 Low Power, Slew-ate-Limited S-485/S-422 Transceiver DESCIPTION The MX485 is low-power transceivers for S-485 and S-422 communication. IC contains one driver and one receiver. The driver slew rates
More informationCMC 14 Common Mode Chokes Series
7 Electrical Data ID Code Inductance Value at C (-/+%) Less than % performance variations versus temperature (- C / + C) Minimum impedance attenuation : Ω from khz to MHz Compact SMD package (x pins) Applied
More informationHigh-Voltage Trench MOS Barrier Schottky Rectifier Ultra Low V F = 0.39 V at I F = 5 A
V3000S, VF3000S, VB3000S, VI3000S High-Voltage Trench MOS Barrier Schottky Rectifier Ultra Low V F = 0.39 V at I F = 5 TMBS TO-220B ITO-220B 3 2 V3000S VF3000S 2 3 CSE 3 TO-263B TO-262 VB3000S VI3000S
More informationUni-directional 1500 W TVS in TO-277 (SMPC) Package FEATURES
Surface Mount PR Transient Voltage Suppressors Uni-directional 500 W TVS in TO-277 (SMPC) Package esmp Series 2 TO-277 (SMPC) PRIMRY CHRCTERISTICS V WM 5.8 V to 43.6 V V BR 6.8 V to 5 V P PPM 500 W T J
More informationLEAKAGE FLUX CONSIDERATIONS ON KOOL Mµ E CORES
LEAKAGE FLUX CONSIDERATIONS ON E CORES Michael W. Horgan Senior Applications Engineer Magnetics Division of Spang & Co. Butler, PA 163 Abstract Kool Mu, a Silicon-Aluminum-Iron powder, is a popular soft
More informationDual Passive Input Digital Isolator. Features. Applications
Dual Passive Input Digital Isolator Functional Diagram Each device in the dual channel IL611 consists of a coil, vertically isolated from a GMR Wheatstone bridge by a polymer dielectric layer. A magnetic
More informationDiscontinued Product
346, 356, and 358 Hall Effect Gear-Tooth Sensor ICs Zero Speed Discontinued Product This device is no longer in production. The device should not be purchased for new design applications. Samples are no
More informationInductance value Rated current Handling power Weight Minimum package quantity
(/6) 00-0 / 00 / e9_uf.fm TDK common mode choke coils(line filters) are used in a wide range of prevention of electromagnetic interference(emi) and radio frequency interference(rfi) from power supply lines
More informationHow to understand MAGNETEC s Datasheet
How to understand MAGNETEC s Datasheet The objective of this document is to help to understand MAGNETEC s core and component datasheets on the examples MB-667-01_01 and M-116-03_05 as being EMC core and
More informationShielded Power Inductors
Shielded Power Inductors MN509 Shielded inductor with minimum EMI Minimum power loss Non standard values available Low DC resistance Flat top for SMT operations Specifications Inductance tested at 100KHz
More informationPOSITIVE ADJUSTABLE VOLTAGE REGULATOR
IP117K IP117K IP117HK IP117HK IP317K IP317K IP317HK IP317HK / LM117K / LM117K / LM117HK / LM117HK / LM317K / LM317K / LM317HK / LM317HK FETURES 1.5 Output Current Guaranteed Internal Thermal Overload Protection
More informationHyperfast Rectifier, 30 A FRED Pt
Hyperfast Rectifier, 30 FRED Pt 2L TO-220C Base cathode 2 2L TO-220 FULL-PK FETURES Hyperfast soft recovery time Low forward voltage drop 75 C operating junction temperature Low leakage current Fully isolated
More informationFerrite for Switching Power Supplies Summary
(/6) Ferrite for Switching Power Supplies Summary Our foremost mission is to develop unique and advanced electronics technologies. As such, ever since TDK was founded in 935 when its researchers invented
More informationInductance value Rated current Handling power Weight Minimum package quantity
(/6) 00-0 / 00505 / e9_uf.fm TDK common mode choke coils(line filters) are used in a wide range of prevention of electromagnetic interference(emi) and radio frequency interference(rfi) from power supply
More informationMAGNETIC-LATCHING ESTABLISHED RELIABILITY TO-5 RELAYS DPDT RELAY TYPE. DPDT relay with internal diode for coil transient suppression
ESTABLISHED RELIABILITY SERIES DESIGNATION MAGNETIC-LATCHING ESTABLISHED RELIABILITY TO-5 RELAYS DPDT 420/422 DPDT basic relay 420D/422D 420DD/422DD RELAY TYPE DPDT relay with internal diode for coil transient
More informationMCR70xA Series. Thyristors. Surface Mount 100V -600V > MCR70xA Series G K. Description
MCR70x Series Pb Description PNPN Componants designed for high volume, low cost consumer applications such as temperature, light and speed control; process and remote control; and warning systems where
More informationINPUT INFO OUTPUT UNIT ACDC_TinySwitch-4_032514_Rev1-1.xls; TinySwitch-4 Continuous/Discontinuous Flyback Transformer Design Spreadsheet
ACDC_TinySwitch-4_032514; Rev.1.1; Copyright Power Integrations 2014 ENTER APPLICATION VARIABLES INPUT INFO OUTPUT UNIT ACDC_TinySwitch-4_032514_Rev1-1.xls; TinySwitch-4 Continuous/Discontinuous Flyback
More informationAPT60GT60JR SOT-227 G E
V 93 The Thunderbolt IGBT is a new generation of high voltage power IGBTs. Using Non-Punch Through Technology the Thunderbolt IGBT offers superior ruggedness and ultrafast switching speed. Low Forward
More informationRF Components. Since 2003
RF Components Pulse offers a comprehensive line of RF magnetic components for use in CATV/ Hybrid Fiber Coax applications for set-top boxes and gateway devices, for TELCO TV in gateway devices, and FTTP
More informationHEXFRED Ultrafast Soft Recovery Diode, 15 A
HEXFRED Ultrafast Soft Recovery Diode, 15 FETURES Ultrafast and ultrasoft recovery 1 TO-247C modified Base common cathode 2 2 3 Very low I RRM and Q rr Designed and qualified according to JEDEC -JESD47
More informationApplications. Pin Configuration. Ordering and Marking Information. Hall Effect Micro Switch IC
Hall Effect Micro Switch IC Features Micro Power Operation for Battery pplications Chopper Stabilized mplifier Independent of North or South Pole Magnet, Easy for Manufacture Small Size Package Lead Free
More informationGaAS MMIC SMT LOW DISTORTION T/R SWITCH DC GHZ
'99 MICROWVE CORPORTI GaS MMIC LOW DISTORTI T/R SWITCH DC - 2.5 GHZ Features General Description HIGH THIRD ORDER INTERCEPT: + m SINGLE POSITIVE SUPPLY: +3 TO +V HIGH POWER CPILITY TTL/CMOS CTROL The is
More informationA3121, A3122, and A3133
A3121, A3122, and A3133 Hall Effect Switches for High Temperature Operation Discontinued Product These parts are no longer in production The device should not be purchased for new design applications.
More informationTherma FM, Ltd. is a Czech producer of wound magnetic cores intended for construction of electrical machines.
Dear customers, Therma FM, Ltd. is a Czech producer of wound magnetic cores intended for construction of electrical machines. We would like to introduce you our new catalogue, which is designed to help
More informationMAC08BT1, MAC08MT1. Thyristors. Surface Mount 200V - 600V > MAC08BT1, MAC08MT1. Description
MAC08BT1, MAC08 Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Sensitive
More informationCommon Mode Choke Coils(Line Filters)
Common Mode Choke Coils(Line Filters) For power line, Closed magnetic circuit core type HF Series Type: Vertical type HF36/HF38 /HF9 For large inductance HF04/HF4/HF430/HF86/HF836/HF3545 Issue date: December
More informationDesign Considerations
Design Considerations APPLICATION NOTES: Multi-hole cores provide specialized shapes that are sometimes more useful than single hole devices. One example is wide band transformers where good coupling between
More informationAmveco Toroidal Solutions. Acme Electric s class leading toroidal magnetics is the perfect solution for the most challenging applications.
Amveco Toroidal Solutions Acme Electric s class leading toroidal magnetics is the perfect solution for the most challenging applications. AMVECO TOROIDAL SOLUTIONS Acme Electric s Amveco brand specializes
More informationData Sheet. AEAT-601B Incremental Magnetic Encoder. Description. Features. Exploded View. Applications
AEAT-601B Incremental Magnetic Encoder Data Sheet Description Avago Technologies Incremental Magnetic Encoder provides an integrated solution for angular detection within a complete 360 rotation. The use
More informationPart Number: Frequency Range: Suppression Applications for Higher Frequencies > 250 MHz (61 material)
Part Number: 2861000302 Frequency Range: Suppression Applications for Higher Frequencies > 250 MHz (61 material) Description: Application: Where Used: Part Type: 61 MULTI-APERTURE CORE Suppression Components
More informationSilicon PIN Photodiode
Silicon PIN Photodiode DESCRIPTION is pin photodiode chip with 0.23 mm 2 sensitive area detecting visible and near infrared radiation. node and cathode are the bond pads on top. FETURES Package type: chip
More informationFeatures. Symbol Parameter Rating Units V DS Drain-Source Voltage 60 V V GS Gate-Source Voltage ±20 V
General Description These N-Channel enhancement mode power field effect transistors are using trench DMOS technology. This advanced technology has been especially tailored to minimize on-state resistance,
More informationMAGNETIC-LATCHING ESTABLISHED RELIABILITY TO-5 RELAYS
MAGNETIC-LATCHING ESTABLISHED RELIABILITY TO-5 RELAYS SPDT SERIES 421 SERIES DESIGNATION RELAY TYPE 421 SPDT basic relay 421D 421DD SPDT relay with internal diode for coil transient suppression SPDT relay
More informationLarge Kool Mµ Core Shapes
Large Kool Mµ Core Shapes Technical Bulletin Ideal for high current inductors, large Kool Mµ geometries (E cores, Toroids, U Cores and Blocks) offer all the advantages of Kool Mµ material, low core loss,
More informationMCR703A Series. Thyristors. Surface Mount 100V -600V > MCR703A Series G K. Description
MCR703 Series Pb Description PNPN devices designed for high volume, low cost consumer applications such as temperature, light and speed control; process and remote control; and warning systems where reliability
More informationOperating Junction and 55 to +175 C Storage Temperature Range
Feathers: dvanced trench process technology avalanche energy, 100% test Fully characterized avalanche voltage and current ID =60 BV=60V Rdson=14mΩ(max.) Description: The is a new generation of middle voltage
More informationCABLE SHIELDING CHO-SORB EMI Ferrites
BLE SHIELING HO-SORB EMI Ferrites HO-SORB EMI Ferrites ost effective HO-SORB EMI ferrites reduce conducted emissions and ES susceptibility on signal lines and power cables without affecting data transmission.
More informationUniversity of Pittsburgh
University of Pittsburgh Experiment #11 Lab Report Inductance/Transformers Submission Date: 12/04/2017 Instructors: Dr. Minhee Yun John Erickson Yanhao Du Submitted By: Nick Haver & Alex Williams Station
More informationINPUT INFO OUTPUT UNIT TOP_JX_032514: TOPSwitch-JX Continuous/Discontinuous Flyback Transformer Design Spreadsheet
ACDC_TOPSwitchJX_032514; Rev.1.6; Copyright Power Integrations 2014 ENTER APPLICATION VARIABLES INPUT INFO OUTPUT UNIT TOP_JX_032514: TOPSwitch-JX Continuous/Discontinuous Flyback Transformer Design Spreadsheet
More informationObsolete Product(s) - Obsolete Product(s)
VB92ZVFI / VB92ZVSP HIGH VOLTGE IGNITION COIL DRIVER POWER I.C. TYPE V cl I cl V cg(sat) VB92ZVFI VB92ZVSP 340V 7.5 2.5V n NO EXTERNL COMPONENT REQUIRED n INTEGRTED HIGH VOLTGE CLMP n COIL CURRENT LIMIT
More informationCommon Mode Chokes BU Series
Document 60- Common Mode Chokes BU Series These low cost, high performance choke coils are designed to virtually eliminate line conducted common mode noise. The BU9S and BU9HS families are ideal for signal
More informationINPUT INFO OUTPUT UNIT TOP_JX_032514: TOPSwitch-JX Continuous/Discontinuous Flyback Transformer Design Spreadsheet
ACDC_TOPSwitchJX_032514; Rev.1.6; Copyright Power Integrations 2014 ENTER APPLICATION VARIABLES INPUT INFO OUTPUT UNIT TOP_JX_032514: TOPSwitch-JX Continuous/Discontinuous Flyback Transformer Design Spreadsheet
More informationWIRE AND CABLE SECTION M WIRE AND CABLE. TEW / TEWN and TR-64 Wire. SPT1 / SPT2 / SEW1 AND SEW2 Wire. SVT / SJT / SO AND SOOW Cords
SECTION M TEW / TEWN and TR-64 Wire SPT / SPT2 / SEW AND SEW2 Wire SVT / SJT / SO AND SOOW Cords Clear Braided Multi Conductor Cable M2 M3 M4 M5 M2 TEW / TEWN AND TR-64 WIRE TEW and TEWN - Single Conductor
More information1.24V Precision Adjustable Shunt Regulator
SPX142 1.24V Precision djustable Shunt Regulator FETURES Reference Voltage: 1.24V Initial ccuracy:.5% Wide Operating Current, 6µ to 1m Ultra Low Reference Input Current, 1n Operating Voltage Range: V REF
More informationOur Position on Quality And the Environment
17t hedi t i on - Our Position on Quality And the Environment Fair-Rite Products Corp. is committed to be "Your Signal Solution". Management and employees continue to adhere to the ISO/TS 16949 quality
More informationTAPE WOUND CORES. 48 Alloy Orthonol Magnesil Permalloy 80 Supermalloy
TAPE WOUND CORES 48 Alloy Orthonol Magnesil Permalloy 80 Supermalloy Orthonol Tape Wound Cores 48 Alloy Magnesil Permalloy 80 Supermalloy Bobbin Cores WEBSITES Visit Magnetics websites for a wealth of
More informationDRQ. Dual winding, high power density, shielded drum core power inductors. Technical Data DS4311. Applications. Environmental data.
Supersedes pril 0 Dual winding, high power density, shielded drum core power inductors pplications Desktop and servers DVD and media players Portable and handheld devices LCD panels s a transformer: SEPIC,
More information+5 V Low Power EIA RS-485 Transceiver ADM1485
a FETUES Meets EI S-8 Standard 3 Mb/s Data ate Single + V Supply 7 V to +12 V us Common-Mode ange High Speed, Low Power icmos Thermal Shutdown Protection Short Circuit Protection Zero Skew Driver Driver
More informationFrom dc to 10 GHz the. VSWR shall not exceed 1.3 &.04 (f) where f is the frequency in Gigahertz (GHz).
121 Series Coaxial Snap On & Screw On Types / 50 Ohm & 75 Ohm These 50 and 75 Ohm coaxial connectors are easily inserted into your printed circuit board using an insertion tool. Solder is eliminated and
More informationLarge Kool Mµ Core Shapes
Large Kool Mµ Core Shapes TECHNICAL BULLETIN Ideal for high current inductors, large Kool Mµ geometries (E cores, U Cores and Blocks) offer all the advantages of Kool Mµ material, low core loss, excellent
More informationMinntronix Technical Note
Minntronix Technical Note Inductance measurement using real-world inductance bridges or What you set may not be what you get Dave LeVasseur VP of Research & Development Minntronix, Inc. 17-Dec-14 The Problems:
More informationFor more information, please visit the product page. output. output current max (A)
date 12/12/217 page 1 of 1 SERIES: VMS-2 DESCRIPTION: AC-DC POWER SUPPLY FEATURES compact 2 x 4 high power-density design (CNF version is 2.4 x 4.6 ) universal input range efficiencies up to 93.5% 4th
More informationP-Channel Enhancement Mode MOSFET
Features -3V/-3, =46mΩ (typ.) @ V GS =-1V =55mΩ (typ.) @ V GS =-4.5V =79mΩ (typ.) @ V GS =-2.5V Super High Dense Cell Design Reliable and Rugged Enhance ESD Cell Protection Lead Free and Green Devices
More informationmj P D Watts T J,T STG T L CAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed.
V 58 The Thunderbolt IGBT is a new generation of high voltage power IGBTs. Using Non-Punch Through Technology the Thunderbolt IGBT offers superior ruggedness and ultrafast switching speed. Low Forward
More informationCAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed.
V 3 Fast IGBT The Fast IGBT is a new generation of high voltage power IGBTs. Using Non-Punch Through Technology the Fast IGBT offers superior ruggedness, fast switching speed and low Collector-Emitter
More informationHALL-EFFECT, DIRECTION-DETECTION SENSORS
Data Sheet 2765.1A* 3422 S V CC X SUPPLY LOGIC DIRECTION E1 GROUND E2 X E1 OUTPUT SPEED Dwg. PH-15 Pinning is shown viewed from branded side. ABSOLUTE IMUM RATINGS Supply Voltage, V CC............. 18
More informationThe Reliable Source... FERROPERM. Inductors. Transformers
The Reliable Source... FERROPERM for High Quality Inductors and Transformers INDUCTORS AND TRANSFORMERS from FERROPERM UK Ltd. FERROPERM offers a manufacturing capability for the production of most types
More information3185 THRU 3189 HALL-EFFECT LATCHES FOR HIGH-TEMPERATURE OPERATION FEATURES. ABSOLUTE MAXIMUM RATINGS at T A = +25 C V CC GROUND OUTPUT SUPPLY
3185 THRU 3189 Data Sheet 2769.2A X V CC These Hall-effect latches are extremely temperature-stable and stressresistant sensors especially suited for operation over extended temperature ranges to +15 C.
More informationFeatures. P-Channel Enhancement Mode MOSFET
P-Channel Enhancement Mode MOSFET Features Pin Description -20V/-3 R DS(ON) = 56mΩ (typ.) @ V GS = -4.5V R DS(ON) = 85mΩ (typ.) @ V GS = -2.5V R DS(ON) = 135mΩ (typ.) @ V GS = -1.8V Super High Dense Cell
More informationSchottky Rectifier, 2 x 30 A
VS-6CPQ5PbF, VS-6CPQ5-N3 Schottky Rectifier, x 3 TO-47C PRODUCT SUMMRY Package TO-47C I F(V) x 3 V R 5 V V F at I F.67 V I RM max. 5 m at 5 C T J max. 75 C Diode variation Common cathode E S 3 node Base
More information2.5mm Pitch Connector for Discrete Wire Connection
.mm Pitch Connector for Discrete Wire Connection DF1 Series Features 1. Board Mounting Height (Crimping Type) mm.mm pitch connector achieves the low profile.. Insulation Displacement Area Protected by
More informationCommon Mode Choke Coils
Common Mode Choke Coils For power line UF series Type: Two sections bobbin type for high frequency UF Issue date: September 0 Conformity to RoHS Directive: This means that, in conformity with EU Directive
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. D 3.00 to 7.92mm (.118 to.312") Pitch FEATURES AND SPECIFICATIONS Features
More informationSegmented Photodiodes (SPOT Series)
Segmented Photodiodes (SPOT Series) Position Sensing Detector (PSD) The SPOT Series are common substrate photodetectors segmented into either two (2) or four (4) separate active areas. They are available
More informationWaveforms for Stimulating Magnetic Cores
Waveforms for Stimulating Magnetic Cores My assigned topic is test waveforms for magnetic cores, but I'm going to provide a little background, which touches on topics covered by other presenters here:
More informationIRF7341. HEXFET Power MOSFET V DSS = 55V. R DS(on) = 0.050Ω
l Generation V Technology l Ultra Low On-Resistance l Dual N-Channel Mosfet l Surface Mount l vailable in Tape & Reel l Dynamic dv/dt Rating l Fast Switching Description Fifth Generation HEXFETs from International
More informationWrap-and-Fill Metalized Polyester Film Capacitors
Type 43P Wrap-and-Fill Metalized Polyester Film Capacitors EECTRICA SPECIFICATIONS Capacitance Range:.1 μf to 1. μf Range: 63 to 16, 4 VAC to 22 VAC Capacitance Tolerance: ±2%, ±1%, ±5% Operating Temperature:
More information