6-PIN DIP ZERO-CROSS OPTOISOLATORS TRIAC DRIVER OUTPUT (250/400 VOLT PEAK)
|
|
- Jocelin Goodwin
- 5 years ago
- Views:
Transcription
1 -PIN DIP ZERO-CROSS DESCRIPTION The MOC303XM and MOC304XM devices consist of a AlGaAs infrared emitting diode optically coupled to a monolithic silicon detector performing the function of a zero voltage crossing bilateral triac driver. They are designed for use with a triac in the interface of logic systems to equipment powered from 5 VAC lines, such as teletypewriters, CRTs, solid-state relays, industrial controls, printers, motors, solenoids and consumer appliances, etc. FEATURES Simplifies logic control of 5 VAC power Zero voltage crossing dv/dt of 000 V/µs typical, 000 V/µs guaranteed VDE recognized (File # 947) -ordering option V (e.g., MOC3043VM) ANODE CATHODE SCHEMATIC MAIN TERM. 5 NC* APPLICATIONS Solenoid/valve controls Static power switches Temperature controls AC motor starters Lighting controls AC motor drives E.M. contactors Solid state relays N/C 3 ZERO CROSSING CIRCUIT *DO NOT CONNECT (TRIAC SUBSTRATE) 4 MAIN TERM. ABSOLUTE MAXIMUM RATINGS (T A = 5 C unless otherwise noted) Parameters Symbol Device Value Units TOTAL DEVICE Storage Temperature T STG All -40 to +50 C Operating Temperature T OPR All -40 to +85 C Lead Solder Temperature T SOL All 0 for 0 sec C Junction Temperature Range T J All -40 to +00 C Isolation Surge Voltage () (peak AC voltage, 0Hz, sec duration) V ISO All 7500 Vac(pk) Total Device Power 5 C 50 mw P D All Derate above 5 C.94 mw/ C EMITTER Continuous Forward Current I F All 0 ma Reverse Voltage V R All V Total Power Dissipation 5 C Ambient 0 mw P D All Derate above 5 C.4 mw/ C DETECTOR MOC303M/M/3M 50 V Off-State Output Terminal Voltage DRM MOC304M/M/3M 400 Peak Repetitive Surge Current (PW = 00 µs, 0 pps) I TSM All A Total Power 5 C Ambient All 50 mw P Derate above 5 C D All.7 mw/ C Note. Isolation surge voltage, V ISO, is an internal device dielectric breakdown rating. For this test, Pins and are common, and Pins 4, 5 and are common. V
2 -PIN DIP ZERO-CROSS ELECTRICAL CHARACTERISTICS (T A = 5 C Unless otherwise specified) INDIVIDUAL COMPONENT CHARACTERISTICS Parameters Test Conditions Symbol Device Min Typ Max Units EMITTER Input Forward Voltage I F = 30 ma V F All.5.5 V Reverse Leakage Current V R = V I R All µa DETECTOR Peak Blocking Current,Either Direction Rated V DRM, I F = 0 (note ) I DRM All 00 na Peak On-State Voltage,Either Direction I TM = 00 ma peak, I F = 0 V TM All.8 3 V Critical Rate of Rise of Off-State Voltage I F = 0 (figure 9, note 3) dv/dt All 000 V/µs TRANSFER CHARACTERISTICS (T A = 5 C Unless otherwise specified.) DC Characteristics Test Conditions Symbol Device Min Typ Max Units MOC303M/MOC304M 5 LED Trigger Current Main terminal voltage = 3V (note ) I FT MOC303M/MOC304M 0 ma MOC3033M/MOC3043M 5 Holding Current, Either Direction I H All 400 µa ZERO CROSSING CHARACTERISTICS (T A = 5 C Unless otherwise specified.) Characteristics Test Conditions Symbol Device Min Typ Max Units Inhibit Voltage I F = rated I FT, MT-MT voltage above which device will not trigger off-state V IH All 0 V Leakage in Inhibited State I F = rated I F, rated V DRM, off-state I DRM All 500 µa Note. Test voltage must be applied within dv/dt rating.. All devices are guaranteed to trigger at an I F value less than or equal to max I FT. Therefore, recommended operating I F lies between max I FT (5 ma for MOC303M & MOC304M, 0 ma for MOC303M & MOC304M, 5 ma for MOC3033M & MOC3043M) and absolute max I F (0 ma). 3. This is static dv/dt. See Figure 9 for test circuit. Commutating dv/dt is a function of the load-driving thyristor(s) only.
3 I FT, NORMALIZED I DRM, LEAKAGE CURRENT (na) V F - FORWARD VOLTAGE (V) I TM, ON-STATE CURRENT (ma) -PIN DIP ZERO-CROSS Figure. LED Forward Voltage vs. Forward Current Figure. On-State Characteristics I F = 30mA T A = 5 o C T A = -40 o C 0. T A = 5 o C T A = 85 o C I F - LED FORWARD CURRENT (ma) V TM, ON-STATE VOLTAGE (VOLTS).3 Figure 3. Trigger Current vs. Temperature 0000 Figure 4. Leakage Current, I DRM vs. Temperature NORMALIZED TO T A = 5 o C
4 I H, HOLDING CURRENT (NORMALIZED) V INH - NORMALIZED I DRM, NORMALIZED I FT, LED TRIGGER CURRENT (NORMALIZED) -PIN DIP ZERO-CROSS Figure 5. I DRM - Leakage in Inhibit State vs. Temperature Figure. LED Current Required to Trigger vs. LED Pulse Width.8. 4 NORMALIZED TO PW IN >> 00 µs.4 I F = RATED I FT PW IN, LED TRIGGER PULSE WIDTH (µs) 3. Figure 7. Holding Current, I H vs. Temperature.3 Figure 8. Inhibit Voltage vs. Temperature NORMALIZED TO T A = 5 o C
5 -PIN DIP ZERO-CROSS +50 for MOC303XM +400 for MOC304XM Vdc PULSE INPUT MERCURY WETTED RELAY R TEST C TEST D.U.T. R = 0 kω X00 SCOPE PROBE. The mercury wetted relay provides a high speed repeated pulse to the D.U.T.. 00x scope probes are used, to allow high speeds and voltages. 3. The worst-case condition for static dv/dt is established by triggering the D.U.T. with a normal LED input current, then removing the current. The variable R TEST allows the dv/dt to be gradually increased until the D.U.T. continues to trigger in response to the applied voltage pulse, even after the LED current has been removed. The dv/dt is then decreased until the D.U.T. stops triggering. is measured at this point and recorded. Figure 9. Static dv/dt Test Circuit APPLIED VOLTAGE WAVEFORM 58 V Vmax = 50 V APPLIED VOLTAGE WAVEFORM 5 V V max = 400 V 0 VOLTS dv/dt = 0.3 Vmax = 58 0 VOLTS dv/dt = 0.3 Vmax = 5 Figure 0. Static dv/dt Test Waveform (MOC303M, MOC303M, MOC3033M) Figure. Static dv/dt Test Waveform (MOC304M, MOC304M, MOC3043M) Typical circuit (Fig, 3) for use when hot line switching is required. In this circuit the hot side of the line is switched and the load connected to the cold or neutral side. The load may be connected to either the neutral or hot line. R in is calculated so that I F is equal to the rated I FT of the part, 5 ma for the MOC3033M and MOC3043M, 0 ma for the MOC303M and MOC304M, or 5 ma for the MOC303M and MOC304M. The 39 ohm resistor and 0.0 µf capacitor are for snubbing of the triac and may or may not be necessary depending upon the particular triac and load used. V CC R in 80 Ω HOT V CC R in 30 Ω HOT 3 MOC303M MOC303M MOC3033M 5 39 Ω * 4 5 VAC 3 MOC304M MOC304M MOC3043M 5 39 Ω * 4 40 VAC k LOAD NEUTRAL LOAD NEUTRAL For highly inductive loads (power factor < 0.5), change this value to 30 ohms. * Figure. Hot-Line Switching Application Circuit (MOC303M, MOC303M, MOC3033M) For highly inductive loads (power factor < 0.5), change this value to 30 ohms. * Figure 3. Hot-Line Switching Application Circuit (MOC304M, MOC304M, MOC3043M)
6 -PIN DIP ZERO-CROSS 5 VAC R D V CC Rin 3 MOC303M MOC303M MOC3033M Ω SCR SCR R D LOAD Figure 4. Inverse-Parallel SCR Driver Circuit (MOC303M, MOC303M, MOC3033M) Suggested method of firing two, back-to-back SCR s with a Fairchild triac driver. Diodes can be N400; resistors, R and R, are optional k ohm. 40 VAC R D V CC Rin 3 MOC304M MOC304M MOC3043M Ω SCR SCR R D LOAD Figure 5. Inverse-Parallel SCR Driver Circuit (MOC304M, MOC304M, MOC3043M) Suggested method of firing two, back-to-back SCR s with a Fairchild triac driver. Diodes can be N400; resistors, R and R, are optional 330 ohm. Note: This optoisolator should not be used to drive a load directly. It is intended to be a trigger device only.
7 -PIN DIP ZERO-CROSS Package Dimensions (Through Hole) Package Dimensions (Surface Mount) (8.89) 0.30 (8.3) PIN ID (8.89) 0.30 (8.3) PIN ID. 0.0 (.0) 0.40 (.0) 0.0 (.0) 0.40 (.0) (9.90) 0.33 (8.43) (.77) (.0) 0.04 (0.3) 0.00 (0.5) 0.30 (8.3) (.77) (.0) 0.04 (0.3) 0.00 (0.5) 0.30 (8.3) 0.00 (5.08) 0.5 (.93) 0.00 (5.08) 0.5 (.93) 0.0 (0.30) (0.0) 0.00 (.54) 0.05 (0.38) 0.00 (0.50) 0.0 (0.4) 0.00 (.54) (0.30) 0.05 (0.3) 0.00 (0.5) 0.00 (0.50) 0.0 (0.4) 0.00 [.54] (8) 0.00 (0.) Package Dimensions (0.4 Lead Spacing) (8.89) 0.30 (8.3) PIN ID. Recommended Pad Layout for Surface Mount Leadform 0.0 (.0) 0.40 (.0) (.78) 0.00 (.5) (.77) (.0) 0.04 (0.3) 0.00 (0.5) 0.45 (0.79) 0.00 (.54) (7.75) (0.7) 0.00 (5.08) 0.5 (.93) 0.00 (.54) 0.05 (0.38) 0.00 (0.50) 0.0 (0.4) 0.00 [.54] 0.0 (0.30) (0.) 0.45 (0) (0.) NOTE All dimensions are in inches (millimeters)
8 ORDERING INFORMATION -PIN DIP ZERO-CROSS Option Order Entry Identifier Description S S Surface Mount Lead Bend SR SR Surface Mount; Tape and reel T T 0.4 Lead Spacing V V VDE 0884 TV TV VDE 0884, 0.4 Lead Spacing SV SV VDE 0884, Surface Mount SRV SRV VDE 0884, Surface Mount, Tape & Reel Carrier Tape Specifications ( D Taping Orientation) 4.5 ± MAX 4.0 ± 0..0 ± 0..0 ± 0.05 Ø.5 MIN.75 ± ± 0..5 ± ± ± MAX 0. ± 0.0 Ø.5 ± 0./-0 User Direction of Feed NOTE All dimensions are in inches (millimeters)
MOC3031M MOC3032M MOC3033M MOC3041M MOC3042M MOC3043M. Parameters Symbol Device Value Units TOTAL DEVICE Storage Temperature. T STG All -40 to +150 C
-PIN DIP ZERO-CROSS DESCRIPTION The MOC303XM and MOC304XM devices consist of a AlGaAs infrared emitting diode optically coupled to a monolithic silicon detector performing the function of a zero voltage
More information6-PIN DIP ZERO-CROSS OPTOISOLATORS TRIAC DRIVER OUTPUT (800 VOLT PEAK)
PACKAGE SCHEMATIC ANODE 1 6 MAIN TERM. CATHODE 2 5 NC* N/C 3 ZERO CROSSING CIRCUIT 4 MAIN TERM. *DO NOT CONNECT (TRIAC SUBSTRATE) DESCRIPTION The MOC3081M, MOC3082M and MOC3083M devices consist of a GaAs
More informationMOC3081M, MOC3082M, MOC3083M 6-Pin Zero-Cross Optoisolators Triac Driver Output (800 Volt Peak)
MOC3081M, MOC308M, MOC3083M 6-Pin Zero-Cross Optoisolators Triac Driver Output (800 Volt Peak) Features Underwriters Laboratories (UL) recognized file #E90700, Volume VDE recognized file #10497 add option
More information6-PIN DIP RANDOM-PHASE OPTOISOLATORS TRIAC DRIVER OUTPUT (250/400 VOLT PEAK)
-PIN DIP RANDOM-PHASE PACKAGE SCHEMATIC ANODE MAIN TERM. CATHODE NC* N/C 3 MAIN TERM. *DO NOT CONNECT (TRIAC SUBSTRATE) DESCRIPTION The MOC30XM and MOC30XM series are optically isolated triac driver devices.
More informationMOC3061M, MOC3062M, MOC3063M, MOC3162M, MOC3163M 6-Pin DIP Zero-Cross Phototriac Driver Optocoupler (600 Volt Peak)
MOC30M, MOC30M, MOC303M, MOC3M, MOC33M -Pin DIP Zero-Cross Phototriac Driver Optocoupler (00 Volt Peak) Features Simplifies logic control of 5/40 VAC power Zero voltage crossing dv/dt of 000V/µs guaranteed
More information6-PIN DIP ZERO-CROSS PHOTOTRIAC DRIVER OPTOCOUPLER (600V PEAK)
PACKAGE SCHEMATIC ANODE CATHODE 2 N/C 3 ZERO CROSSING CIRCUIT MAIN TERM. 5 NC* 4 MAIN TERM. *DO NOT CONNECT (TRIAC SUBSTRATE) DESCRIPTION The MOC30X-M and MOC3X-M devices consist of a GaAs infrared emitting
More informationMOC3010M, MOC3011M, MOC3012M, MOC3020M, MOC3021M, MOC3022M, MOC3023M 6-Pin DIP Random-Phase Optoisolators Triac Driver Output (250/400 Volt Peak)
March 2014 MOC3010M, MOC3011M, MOC3012M, MOC3020M, MOC3021M, MOC3022M, MOC3023M 6-Pin DIP Random-Phase Optoisolators Triac Driver Output (250/400 Volt Peak) Features Excellent I FT Stability IR Emitting
More information(400 Volts Peak) COUPLER SCHEMATIC STANDARD THRU HOLE
GlobalOptoisolator (00 Volts Peak) The MOC0, MOC02 and MOC0 devices consist of gallium arsenide infrared emitting diodes optically coupled to a monolithic silicon detector performing the function of a
More informationMOC3010M, MOC3011M, MOC3012M, MOC3020M, MOC3021M, MOC3022M, MOC3023M 6-Pin DIP Random-Phase Triac Driver Output Optocoupler (250/400 Volt Peak)
MOC3010M, MOC3011M, MOC301M, MOC300M, MOC301M, MOC30M, MOC303M 6-Pin DIP Random-Phase Triac Driver Output Optocoupler (0/400 Volt Peak) Features Excellent I FT Stability IR Emitting Diode Has Low Degradation
More information6-PIN DIP RANDOM-PHASE OPTOISOLATORS TRIAC DRIVERS (600 VOLT PEAK)
PACKAGE SCHEMATIC 6 6 ANODE CATHODE 2 6 MAIN TERM. 5 NC* N/C 3 4 MAIN TERM. 6 *DO NOT CONNECT (TRIAC SUBSTRATE) DESCRIPTION The and consist of a AlGaAs infrared emitting diode optically coupled to a non-zero-crossing
More information(250 Volts Peak) COUPLER SCHEMATIC. MAXIMUM RATINGS (TA = 25 C unless otherwise noted) Rating Symbol Value Unit STYLE 6 PLASTIC
(0 Volts Peak) The Series consists of gallium arsenide infrared emitting diodes, optically coupled to silicon bilateral switch and are designed for applications requiring isolated triac triggering, low
More informationPRODUCT DATASHEET. is brought to you by. SOS electronic distribution of electronic components
PRODUCT DATASHEET is brought to you by SOS electronic distribution of electronic components Click to view availability, pricing and lifecycle information. Visit https://www.soselectronic.com/ Datasheet
More information6 PIN DIP ZERO-CROSS TRIAC DRIVER PHOTOCOUPLER EL303X, EL304X, EL306X, EL308X Series
Schematic 1 6 2 5 Features: 3 Zero Crossing Circuit 4 Peak breakdown voltage - 250V: EL303X - 400V: EL304X - 600V: EL306X - 800V: EL308X High isolation voltage between input and output (Viso=5000 V rms
More information4 PIN DIP ZERO-CROSS TRIAC DRIVER PHOTOCOUPLER ELT304X, ELT306X, ELT308X Series
Schematic Features: Peak breakdown voltage - 400V: ELT304X - 600V: ELT306X - 800V: ELT308X High isolation voltage between input and output (Viso=5000 V rms ) Zero voltage crossing Pb free and RoHS compliant.
More informationMOC3051M, MOC3052M 6-Pin DIP Random-Phase Optoisolators Triac Drivers (600 Volt Peak)
MOC3051M, MOC3052M 6-Pin DIP Random-Phase Optoisolators Triac Drivers (600 Volt Peak) Features Excellent I FT Stability IR Emitting Diode Has Low Degradation 600 V Peak Blocking Voltage Safety and Regulatory
More information4 PIN DIP ZERO-CROSS TRIAC DRIVER PHOTOCOUPLER ELT304X, ELT306X, ELT308X Series
Schematic Features: Peak breakdown voltage - 400V: ELT304X - 600V: ELT306X - 800V: ELT308X High isolation voltage between input and output (Viso=5000 V rms ) Zero voltage crossing Pb free and RoHS compliant.
More informationIs Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
More information4 PIN SOP ZERO-CROSS TRIAC PHOTOCOUPLER ELM304X, ELM306X, ELM308X Series
Schematic Features: Peak breakdown voltage - 400V: ELM304X - 600V: ELM306X - 800V: ELM308X High isolation voltage between input and output (Viso=3750 V rms ) Zero voltage crossing Pb free and RoHS compliant.
More informationKMOC308X Series. cosmo 5PIN ZERO-CROSS TRIAC DRIVER PHOTOCOUPLER. Description. Schematic. Features. Applications Z.C. The KMOC3081 KMOC3082 KMOC3083
Description The KMOC381 KMOC382 KMOC383 Schematic series consist of a GaAs infrared emitting diode 1 6 optically coupled to a monolithic silicon detector performing the function of a zero voltage crossing
More informationKMOC3012 Series 4PIN ZERO-CROSS TRIAC DRIVER PHOTOCOUPLER
Description Schematic The KMOC312 series consist of a GaAs infrared emitting diode optically coupled to a 1 4 monolithic silicon detector performing the function of a zero voltage crossing bilateral TRIAC
More informationEL301X Series EL302X Series EL305X Series 6 PIN DIP RANDOM-PHASE TRIAC DRIVER PHOTOCOUPLER. Features: Description. Applications
Features: Peak breakdown voltage - 250V: EL301X - 400V: EL302X - 600V: EL305X High isolation voltage between input and output (Viso=5000 V rms ) Compact dual-in-line package Pb free and RoHS compliant.
More information6 PIN DIP RANDOM-PHASE TRIAC DRIVER PHOTOCOUPLER EL301X, EL302X, EL305X Series
6 PIN DIP RANDOM-PHASE TRIAC DRIVER PHOTOCOUPLER EL301X, EL302X, EL305X Series Schematic 1 6 2 5 Features: Peak breakdown voltage - 250V: EL301X - 400V: EL302X - 600V: EL305X High isolation voltage between
More information6 PIN DIP RANDOM-PHASE TRIAC DRIVER PHOTOCOUPLER EL301X, EL302X, EL305X Series
6 PIN DIP RANDOM-PHASE TRIAC DRIVER PHOTOCOUPLER Schematic 1 6 2 5 Features: Peak breakdown voltage - 250V: EL301X - 400V: EL302X - 600V: EL305X High isolation voltage between input and output (Viso=5000
More informationHIGH VOLTAGE PHOTOTRANSISTOR OPTOCOUPLERS
DESCRIPTION The HDX and 4N38 are phototransistor-type optically coupled optoisolators. An infrared emitting diode manufactured from specially grown gallium arsenide is selectively coupled with a high voltage
More information4 PIN DIP RANDOM-PHASE TRIAC DRIVER PHOTOCOUPLER ELT302X, ELT305X Series
4 PIN DIP RANDOM-PHASE TRIAC DRIVER PHOTOCOUPLER ELT302X, ELT305X Series Schematic Features: Peak breakdown voltage - 400V: ELT302X - 600V: ELT305X High isolation voltage between input and output (Viso=5000
More informationFODM3011, FODM3012, FODM3022, FODM3023, FODM3052, FODM Pin Full Pitch Mini-Flat Package Random-Phase Triac Driver Output Optocouplers
FODM3, FODM3, FODM3, FODM33, FODM35, FODM353 -Pin Full Pitch Mini-Flat Package Random-Phase Triac Driver Output Optocouplers Features Compact -pin Surface Mount Package (. mm Maximum Standoff Height) Peak
More informationHIGH VOLTAGE PHOTODARLINGTON OPTOCOUPLERS
DESCRIPTION The HGX series are photodarlington-type optically coupled optocouplers. These devices have a gallium arsenide infrared emitting diode coupled with a silicon darlington connected phototransistor
More informationMOC3061M, MOC3062M, MOC3063M, MOC3162M, MOC3163M 6-Pin DIP Zero-Cross Phototriac Driver Optocoupler (600 Volt Peak)
MOC3061M, MOC306M, MOC3063M, MOC316M, MOC3163M 6-Pin DIP Zero-Cross Phototriac Driver Optocoupler (600 Volt Peak) Features Simplifies logic control of 115/40 VAC power Zero voltage crossing dv/dt of 1000V/µs
More informationKTLP3616 (3506) Series 8PIN RANDOM-PHASE TRIAC DRIVER PHOTOCOUPLER
Description The KTLP3616 series consist of a GaAs infrared emitting diode optically coupled to an non-zero-crossing silicon bilateral TRIAC and a main output power TRIAC. These devices isolate low voltage
More informationKTLP3616 (3506), (3502) Series 8PIN RANDOM-PHASE TRIAC DRIVER PHOTOCOUPLER
Description The KTLP3502 series consist of a GaAs infrared emitting diode optically coupled to an non-zero-crossing silicon bilateral TRIAC and a main output power TRIAC. These devices isolate low voltage
More informationFOD420, FOD4208, FOD4216, FOD Pin DIP Triac Drivers
FOD420, FOD4208, FOD42, FOD428 -Pin DIP Triac Drivers Features 300mA on-state current High blocking voltage 800V (FOD4208, FOD428) 00V (FOD420, FOD42) High trigger sensitivity.3ma (FOD42, FOD428) 2mA (FOD420,
More informationMOC215-M MOC216-M MOC217-M
DESCRIPTION These devices consist of a gallium arsenide infrared emitting diode optically coupled to a monolithic silicon phototransistor detector, in a surface mountable, small outline, plastic package.
More informationIs Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
More informationISOCOM. MF303x, MF304x, MF306x, MF308x COMPONENTS DESCRIPTION FEATURES ABSOLUTE MAXIMUM RATINGS APPLICATIONS ORDER INFORMATION
DESCRIPTION The MF304x, MF306x and MF308x series of devices consist of a GaAs infrared emitting diode optically coupled to a monolithic silicon detector performing the function of a zero voltage crossing
More information600 V IL V IL4108 Zero Voltage Crossing Detector Triac Optocoupler
FEATURES High Input Sensitivity I FT =.0 ma, PF=.0 I FT =.0 ma, PF.0 00 ma On-State Current Zero Voltage Crossing Detector 00/800 V Blocking Voltage High Static dv/dt 0 kv/µs Inverse Parallel SCRs Provide
More information7PIN DIP PHOTO POWER TRIAC PHOTOCOUPLER ELRX223 Series
Features Low trigger current T 10mA Peak off state voltage 600V Load current 0.3,0.6,0.9,1.2A Wide operating temperature range of -40 C to 85 C High isolation voltage between input and output (Viso=5000
More informationOptocoupler, Phototriac Output, Zero Crossing, Very Low Input Current
2842- IL46, IL47, IL48 Optocoupler, Phototriac Output, Zero Crossing, Very Low Input Current i793_4 DESCRIPTION The IL46, IL47, and IL48 consists of an AlGaAs IRLED optically coupled to a photosensitive
More informationH11G1M, H11G2M 6-Pin DIP High Voltage Photodarlington Optocouplers
HGM, HG2M 6-Pin DIP High Voltage Photodarlington Optocouplers Features High BV CEO : 00 V Minimum for HGM 80 V Minimum for HG2M High Sensitivity to Low Input Current (Minimum 500% CTR at I F = ma) Low
More informationMOC3020 THRU MOC3023 OPTOCOUPLERS/OPTOISOLATORS
MOC300 THRU MOC303 SOES05A OCTOBER 98 REVISED APRIL 998 00 V Phototriac Driver Output Gallium-Arsenide-Diode Infrared Source and Optically-Coupled Silicon Traic Driver (Bilateral Switch) UL Recognized...
More informationOptocoupler, Phototriac Output, High dv/dt, Low Input Current
IL42, IL428 Optocoupler, Phototriac Output, High dv/dt, Low Input Current A 6 MT2 FEATURES High input sensitivity I FT = 2 ma C 2 NC 6 V, 8 V blocking voltage 2842- NC i793_2 3 4 V D E MT 3 ma on-state
More informationMOC3009 THRU MOC3012 OPTOCOUPLERS/OPTOISOLATORS
5 V Phototriac Driver Output Gallium-Arsenide-Diode Infrared Source and Optically Coupled Silicon Traic Driver (Bilateral Switch) UL Recognized...File Number E585 High Isolation...75 V Peak Output Driver
More informationOptocoupler, Phototriac Output, Zero Crossing, High dv/dt, Low Input Current
Optocoupler, Phototriac Output, Zero Crossing, High dv/dt, Low Input Current 2842- i79030_4 A C 2 NC 3 ZCC* 4 MT *Zero crossing circuit 6 5 V D E MT2 NC FEATURES High static dv/dt 5 kv/μs High input sensitivity
More informationOptocoupler, Phototriac Output, Non-Zero Crossing, 0.5 kv/μs dv/dt, 600 V
Optocoupler, Phototriac Output, Non-Zero Crossing,.5 kv/μs dv/dt, 6 V FEATURES High static dv/dt >.5 kv/μs A 4 MT2 Input sensitivity I FT = 5 ma, 7 ma, and ma On-state RMS current I T(RMS) = 7 ma i7966
More informationH11F1M, H11F2M, H11F3M Photo FET Optocouplers
, H11F2M, H11F3M Photo FET Optocouplers Features As a remote variable resistor: 100Ω to 300MΩ 15pF shunt capacitance 100GΩ I/O isolation resistance As an analog switch: Extremely low offset voltage 60
More informationSamples. Symbol Parameter Test Conditions Value Unit RMS on-state current T C = 100 C 40 A I T(AV) Average on-state current T C
Sxx40x Series RoHS Description Excellent unidirectional switches for phase control applications such as heating and motor speed controls. Standard phase control SCRs are triggered with few milliamperes
More informationMAC210A8, MAC210A10. Thyristors. Surface Mount 400V - 800V > MAC210A8, MAC210A10. Description
MAC210A8, MAC210A10 Pb Description Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full wave silicon gate
More informationCNY17-X Series CNY17F-X Series 6 PIN DIP PHOTOTRANSISTOR PHOTOCOUPLER. Features. Description. Applications
Features Current transfer ratios in selected narrow range groups CNY17-1, CNY17F-1: 40-80% CNY17-2, CNY17F-2: 63-125% CNY17-3, CNY17F-3: 100-200% CNY17-4, CNY17F-4:160-320% High isolation voltage between
More informationMOC3061M, MOC3062M, MOC3063M, MOC3162M, MOC3163M 6-Pin DIP Zero-Cross Triac Driver Optocoupler (600 Volt Peak)
September 2015 MOC3061M, MOC3062M, MOC3063M, MOC3162M, MOC3163M 6-Pin DIP Zero-Cross Triac Driver Optocoupler (600 Volt Peak) Features Simplifies Logic Control of 115/240 VAC Power Zero Voltage Crossing
More informationHIGH SPEED-10 MBit/s LOGIC GATE OPTOCOUPLERS
HIGH SPEED- MBit/s DESCRIPTION The, /6 single-channel and /6 dual-channel optocouplers consist of a 5 nm AlGaAS LED, optically coupled to a very high speed integrated photodetector logic gate with a strobable
More informationApplication Note AN-3006 Optically Isolated Phase Controlling Circuit Solution
www.fairchildsemi.com Application Note AN-3006 Optically Isolated Phase Controlling Circuit Solution Introduction Optocouplers simplify logic isolation from the ac line, power supply transformations, and
More informationOptocoupler, Phototriac Output, Zero Crossing, High dv/dt, Low Input Current
2842- Optocoupler, Phototriac Output, Zero Crossing, i793_4 A DESCRIPTION The IL4 and IL48 consists of a GaAs IRLED optically coupled to a photosensitive zero crossing TRIAC network. The TRIAC consists
More informationMOC3051M, MOC3052M, MOC3053M. 6-Pin DIP Random-Phase Triac Driver Optocoupler (600 Volt Peak)
MOC3051M, MOC3052M, MOC3053M 6-Pin DIP Random-Phase Triac Driver Optocoupler (600 Volt Peak) The MOC3051M, MOC3052M and MOC3053M consist of a GaAs infrared emitting diode optically coupled to a non-zero-
More informationOptocoupler, Power Phototriac
Optocoupler, Power Phototriac 22663 PIN 2 LED anode 3 LED cathode 4 No connection 5 No connection 6 No connection 7 No connection 9, 13 Triac T2 11 Triac T1 15 Triac gate 2 3 4 5 6 7 FUNCTION 15 13 11
More information8 PIN DIP HIGH SPEED 1Mbit/s TRANSISTOR PHOTOCOUPLER
Features High speed 1Mbit/s High isolation voltage between input and output (Viso=5000 Vrms ) Guaranteed performance from 0 C to 70 C Wide operating temperature range of -55 C to 100 C Pb free and RoHS
More informationQJxx16xHx Series. Thyristors 16 Amp High Temperature Alternistor Triacs. RoHS. Description
RoHS Description This 16A high temperature alternistor triac solid state switch series is designed for AC switching and phase control applications such as motor speed and temperature modulation controls,
More information4N2X Series 4N3X Series H11AX Series 6 PIN DIP PHOTOTRANSISTOR PHOTOCOUPLER. Features: Description. Applications
Features: 4N2X series: 4N25, 4N26, 4N27, 4N28 4N3X series: 4N35, 4N36, 4N37, 4N38 H11AX series: H11A1, H11A2, H11A3, H11A4, H11A5 High isolation voltage between input and output (Viso=5000 V rms) Creepage
More informationMCR8NG. Thyristors. Surface Mount 600V - 800V > MCR8NG. Description
Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half wave, silicon gate controlled devices are needed.
More informationHIGH SPEED-10 MBit/s LOGIC GATE OPTOCOUPLERS
DESCRIPTION The, /6 single-channel and /6 dual-channel optocouplers consist of a 5 nm AlGaAS LED, optically coupled to a very high speed integrated photodetector logic gate with a strobable output. This
More information8 PIN DIP HIGH SPEED 1Mbit/s TRANSISTOR PHOTOCOUPLER
Features High speed 1Mbit/s High isolation voltage between input and output (Viso=5000 Vrms ) Guaranteed performance from 0 C to 70 C Wide operating temperature range of -55 C to 100 C Pb free and RoHS
More informationTeccor brand Thyristors 40 Amp Low T q SCR. Symbol Parameter Test Conditions Value Unit RMS on-state current T C = 100 C 40 A I T(AV)
RoHS Description The S4040xQx series of s offer fast turn-off time (tq) characteristics required for applications such as power inverters, switching regulator, and high frequency pulse circuits. These
More informationTeccor brand Thyristors Silicon Controlled Rectifiers
Sx02xS EV Series Amp Sensitive SCR Description New Amp sensitive gate SCR series offers high static dv/dt with low turn off time (tq) through small die planar construction design. All SCR s junctions are
More informationTLP561G TLP561G. Triac Driver Programmable Controllers AC Output Module Solid State Relay. Pin Configuration (top view)
TLP56G TOSHIBA Photocoupler GaAs Ired & Photo Triac TLP56G Triac Driver Programmable Controllers AC Output Module Solid State Relay Unit in mm The TOSHIBA TLP56G consists of a zero voltage crossing turn
More informationFOD420, FOD4208, FOD4216, FOD Pin DIP Triac Drivers
FOD420, FOD4208, FOD42, FOD428 -Pin DIP Triac Drivers Features 300mA on-state current High blocking voltage 800V (FOD4208, FOD428) 00V (FOD420, FOD42) High trigger sensitivity.3ma (FOD42, FOD428) 2mA (FOD420,
More informationGENERAL PURPOSE 6-PIN PHOTOTRANSISTOR OPTOCOUPLERS
DESCRIPTION The device consists of a gallium arsenide infrared emitting diode optically coupled to a high voltage, silicon, phototransistor detector in a standard 6-pin DIP package. It is designed for
More informationOptocoupler, Phototriac Output, Zero Crossing, 1.5 kv/μs dv/dt, 600 V
Optocoupler, Phototriac Output, Zero Crossing, 1.5 kv/μs dv/dt, 6 V FEATURES 15 V/μs dv/dt minimum 6 V blocking voltage ma on-state current Zero crossing detector A C 1 2 6 5 MT2 NC Low input trigger current
More informationThyristors 12 Amp Alternistor (High Communitation) Triacs
Qxx12xHx Series RoHS Description This 12 Amp bidirectional solid state switch series is designed for AC switching and phase control applications such as motor speed and temperature modulation controls,
More information4 PIN DIP PHOTOTRANSISTOR PHOTOCOUPLER. EL2501-G Series. Features: Description. Applications
Features: Halogens free. Current transfer ratio (CTR: 80~600% at I F =5mA, V CE =5V) High isolation voltage between input and output (Viso=5000 V rms ) Creepage distance >7.62 mm Operating temperature
More informationAgilent 4N35 Phototransistor Optocoupler General Purpose Type
Agilent N3 Phototransistor Optocoupler General Purpose Type Data Sheet Description The N3 is an optocoupler for general purpose applications. It contains a light emitting diode optically coupled to a phototransistor.
More information4 PIN DIP LOW INPUT PHOTOTRANSISTOR PHOTOCOUPLER EL8171-G Series
Schematic Features: Current transfer ratio (CTR: 50~300% at I F =0.5mA, V CE =5V) High isolation voltage between input and output (Viso=5000 V rms ) Creepage distance >7.62 mm Operating temperature up
More informationMCT6, MCT61, MCT62 Dual Phototransistor Optocouplers
MCT6, MCT6, MCT62 Dual Phototransistor Optocouplers Features Two isolated channels per package Two packages fit into a 6 lead DIP socket Choice of three current transfer ratios Underwriters Laboratory
More informationOptocoupler, Phototriac Output, Non-Zero Crossing, High dv/dt, Low Input Current
Optocoupler, Phototriac Output, Non-Zero Crossing, High dv/dt, Low Input Current FEATURES High isolation distance on output High static dv/dt V/μs High input sensitivity I FT = ma A 6 MT2 ma on-state current
More informationMCR8SDG, MCR8SMG, MCR8SNG
MCR8SDG, MCR8SMG, MCR8SNG Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half wave, silicon gate controlled
More informationTeccor brand Thyristors 12 Amp Standard SCR. Symbol Parameter Test Conditions SRR6012x1 Unit I T(RMS) RMS on-state current T C
RoHS Description Excellent unidirectional switches for phase control and general switching applications such as heating, motor control controls, converters / rectifiers and capacitive discharge ignitions.
More information8 PIN SOP PHOTOTRANSISTOR DUAL CHANNEL PHOTOCOUPLER. ELD20X / 21X series. Features. Dual channel coupler. Description.
Features Dual channel coupler Current transfer ratios offered in narrow ranges ELD205: 40-80% ELD206: 63-125% ELD207: 100-200% ELD211: > 20% ELD213: > 100% ELD217: > 100% High isolation voltage between
More information4 PIN DIP PHOTOTRANSISTOR PHOTOCOUPLER
Features: Current transfer ratio (CTR: 50~600% at I F =5mA, V CE =5V) (CTR: 63~320% at I F =10mA, V CE =5V) High isolation voltage between inputs and output (Viso=5000 V rms) Creepage distance >7.62 mm
More informationMCR8DSM, MCR8DSN. Thyristors. Surface Mount 600V - 800V > MCR8DSM, MCR8DSN G K. Description
MCR8DSM, MCR8DSN Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Small Size
More information8 PIN DIP PHOTOTRANSISTOR PHOTOCOUPLER EL827 Series
EL827 Series Schematic Features: Current transfer ratio (CTR: 50~600% at I F =5mA, V CE =5V) High isolation voltage between input and output (Viso=5000 V rms ) Compact small outline package Pb free and
More information4 PIN SOP PHOTOTRANSISTOR AC INPUT PHOTOCOUPLER. EL3H4-G Series. Features: Description. Applications
Features: AC input response Current transfer ratio (CTR: Min. 20% at I F =±1mA,V CE =5V) High isolation voltage between input and output (Viso=3750 V rms ) Compact small outline package Pb free and RoHS
More information4 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLER. EL101X-G Series. Features: Description. Applications
Features: Free halogens compliant Current transfer ratio (CTR: 50~600% at I F =5mA, V CE =5V) (CTR: 63~320% at I F =10mA, V CE =5V) High isolation voltage between input and output (Viso=5000 V rms ) Compact
More information4 PIN SOP PHOTOTRANSISTOR PHOTOCOUPLER. EL357 Series. Features: Description. Applications
Features: Current transfer ratio (CTR: 50~600% at I F =5mA, V CE =5V) High isolation voltage between input and output (Viso=3750 V rms ) Compact small outline package Pb free and RoHS compliant. UL approved
More informationcosmo ELECTRONICS CORPORATION
DATE:5/5/ NO.6P4 KMOC6 SHEET OF 6 Zero Crossing Optoisolators TRIAC Features Driver Output (6V Volts Peak). Compact dual-in-line package. 2. 6V peak blocking voltage.. Isolation voltage between input and
More information8 PIN DIP DUAL CHANNEL HIGH SPEED 1Mbit/s TRANSISTOR PHOTOCOUPLER EL253X series
Schematic Features High speed 1Mbit/s 10kV/μs min. common mode transient immunity (EL2611) Guaranteed performance from -40 to 85 Logic gate output High isolation voltage between input and output (Viso=5000
More informationGENERAL PURPOSE SOLID STATE RELAY 8PIN DIP 2-CHANNEL TYPE FORM A SSR
Schematic Features Compact 8-pin DIP size Applicable for 2 Form A use as well as two independent 1Form A use Controls low-level analog signals High sensitivity and high speed response Low-level off state
More informationAC/DC to Logic Interface Optocouplers Technical Data
H AC/DC to Logic Interface Optocouplers Technical Data HCPL-37 HCPL-376 Features Standard (HCPL-37) and Low Input Current (HCPL-376) Versions AC or DC Input Programmable Sense Voltage Hysteresis Logic
More informationOptocoupler, Phototriac Output, Non-Zero Crossing, 250 V DRM
Optocoupler, Phototriac Output, Non-Zero Crossing, 25 V DRM SMD A C 2 6 5 MT2 NC FEATURES Isolation materials according to UL 94 V- Special construction: therefore, extra low coupling capacity of typical.2
More informationMAC08BT1, MAC08MT1. Thyristors. Surface Mount 200V - 600V > MAC08BT1, MAC08MT1. Description
MAC08BT1, MAC08 Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Sensitive
More informationOptocoupler, Phototriac Output, 400 V DRM
VO32, VO321, VO322, VO323 Optocoupler, Phototriac Output, 4 V DRM DESCRIPTION i1794-14 Note: pin 5 must not be connected ~ ~ 6 5 4 1 2 3 A (+) C (-) NC The VO32 series consists of a phototriac optically
More informationTLP3061(S),TLP3062(S),TLP3063(S)
TOSHIBA Photocoupler GaAs Ired & Photo Triac TLP6(S),TLP6(S),TLP6(S) TLP6(S),TLP6(S),TLP6(S) Office Machine Household Use Equipment Triac Driver Solid State Relay Unit in mm The TOSHIBA TLP6 (S), TLP6
More informationC122F1G. Thyristors. Surface Mount 50V > C122F1G. Description
Pb Description Designed primarily for full-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half wave silicon gate controlled, solid state devices
More information8 PIN DIP HIGH SPEED 10MBit/s LOGIC GATE PHOTOCOUPLER
Features: High speed 10Mbit/s Fan out of 8 over -40 to 85 Logic gate output High isolation voltage between input and output (Viso=5000 V rms ) Compact small outline package Pb free and RoHS compliant.
More information8 PIN DIP LOW INPUT CURRENT HIGH GAIN SPLIT DARLINGTON PHOTOCOUPLER 6N138 6N139
Schematic 1 8 2 7 Features High current transfer ratio 2000% typical High isolation voltage between input and output (Viso=5000 Vrms ) Guaranteed performance from 0 C to 70 C Pb free and RoHS compliant.
More information8 PIN DIP HIGH SPEED 1Mbit/s TRANSISTOR PHOTOCOUPLER 6N135 6N136 EL450x Series
8 PIN DIP HIGH SPEED 1Mbit/s TRANSISTOR PHOTOCOUPLER EL450x Series Schematic / / EL4503 1 8 1 8 Features High speed 1Mbit/s High isolation voltage between input and output (Viso=5000 Vrms ) Guaranteed
More informationMAC12HCDG, MAC12HCMG, MAC12HCNG
MAC2HCDG, MAC2HCMG, MAC2HCNG Pb Description Designed primarily for full-wave ac control applications, such as motor controls, heating controls or dimmers; or wherever full wave, silicon gate controlled
More information4 PIN DIP HIGH VOLTAGE PHOTODARLINGTON PHOTOCOUPLER EL852 Series
EL852 Series Schematic Features: High collector- emitter voltage (VCEO=350V) Current transfer ratio (CTR: 1000% min. at I F =1mA, V CE =2V) High isolation voltage between input and output (Viso=5000 V
More information6 PIN DIP PHOTOTRANSISTOR PHOTOCOUPLER 4N2X Series 4N3X Series H11AX Series
Schematic Features: 4N2X series: 4N25, 4N26, 4N27, 4N28 4N3X series: 4N35, 4N36, 4N37, 4N38 H11AX series: H11A1, H11A2, H11A3, H11A4, H11A5 High isolation voltage between input and output (Viso=5000 V
More informationFODM3062, FODM3063, FODM3082, FODM Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
FODM362, FODM363, FODM382, FODM383 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers Features dv/dt of 6V/µs guaranteed Compact 4-pin surface mount package (2.4mm maximum standoff
More information8 PIN DIP HIGH SPEED LOW INPUT CURRENT LOGIC GATE PHOTOCOUPLER EL220X SERIES
Features 1kV/μs min. common mode transient immunity Guaranteed performance from -40 to 85 Wide V CC range (4.5V to 20V) 5Mbd typical signal rate Low input current (1.6mA) High isolation voltage between
More informationOptocoupler, Phototriac Output, Zero Crossing, High dv/dt, Low Input Current
Optocoupler, Phototriac Output, VO4157, VO4158 i179030 A C NC 1 2 3 ZCC* 6 5 4 MT2 NC MT1 *Zero crossing circuit FEATURES High static dv/dt 5 kv/µs High input sensitivity I FT = 1.6, 2, and 3 ma 300 ma
More information4 PIN DIP PHOTOTRANSISTOR PHOTOCOUPLER AC INPUT PHOTOCOUPLER EL814 Series
Schematic Features: AC input response Current transfer ratio (CTR: Min. 20% at I F =±1mA,V CE =5V) High isolation voltage between input and output (Viso=5000 V rms ) Wide Operating temperature range -55~110ºC
More informationDescription. Applications. Features: 1. Anode 2. Cathode 3. Emitter 4. Collector. between input and outpu.
4 PIN DIP PHOTOTRANSISTOR PHOTOCOUPLER EL817 Series Schematic Features: Current transfer ratio (CTR: 50~600% at I F =5mA, V CE =5V) High isolation voltage between input and outpu (Viso=5000 V rms ) Creepagee
More information