Ultimate Push Button Astragal Prehanger Installation Instructions
|
|
- Nancy Butler
- 5 years ago
- Views:
Transcription
1 Ultimte Push Button Astrgl Prehnger Instlltion Instructions Tools Required: Flthed Screwdriver Shers Phillips Screwdriver Power Drill with 1" Drill Bit Tpe Mesure Kit Includes: Full Astrgl Full Length Trim Strip Screw Pck Field Pck Screw Pck Contins: (10) #8 x 1-5/8" screws (4) #8 x 1" screws 8817 West Mrket Street Colfx, NC Product Reference Guide D-Shped Cutout in Trim Strip Olong Cutout for Finger Notches in Trim Strip Trim Strip with Seling Fin Olong Cutout for Finger Notches in Trim Strip D-Shped Cutout in Trim Strip Upper Trim Cp Lower Trim Cp Upper Bolt Sleeve Snp-In Strike Retiner Dummy Strike Plte Finger Notch Push Button Lower Bolt Sleeve Simple Solution Corner Pd Rev. Dte: Endur Products, Inc. Innovtion protected under ptents nd ptents pending in U.S. nd Cnd. See # ULTPREHINST 1
2 INITIAL PREPARATION BEFORE YOU BEGIN: Ensure you hve the pproprite length nd hnding of strgl for your door. Remove the trim strip nd screw pck from the strgl ody nd set side. If tpe is present on the ck of the strgl, peel off the cking. Confirm thickness of your door pnel. For door pnels with thicknesses of 1-11/16", pply the ville B-sel gsket to ccommodte the gp etween the fce of the pnel nd the strgl. Lip should e snug ginst pnel. If present, peel tpe cking. Top View of Inctive Door B-Sel Gsket STEP 1: PLACE ASTRAGAL ON DOOR PANEL INSWING Exterior Top View of Inctive Door Interior OUTSWING Inctive Door Pnel Inctive Door Exterior Top View of Inctive Door Interior. Align the strgl ody flush with the end of the inctive door pnel, with the wide side of the strgl correctly oriented sed on swing of the door. For Inswing doors: Wide side of strgl goes on outside of the door. For Outswing doors: Wide side of strgl goes on inside of the door.. Press strgl down long the length of the pnel. Three ornge securing pins will pop up - two on the upper olt nd one on the lower olt. Do not remove pins t this time.! If present, ensure cking of tpe is removed efore pressing down. 2
3 STEP 2: SECURE ASTRAGAL TO DOOR PANEL Plese refer Product Reference Guide on Pge 1 to identify different components of the strgl. For Step 2, only tighten screws until flush with mting surfces. Do not overtighten screws. Upper Bolt Shown Upper Bolt Shown Lower Bolt Shown c. Keeping the ornge securing pins in plce on the upper olt, secure two #8 x 1-5/8" screws in the holes djcent to the pins.. Next, replce the ornge securing pins with two #8 x 1-5/8" screws. c. Keeping the ornge pins in plce on the lower olt, secure #8 x 1-5/8" screw in the hole djcent to the pin. Lower Bolt Shown d e X 4 d. Replce the ornge securing pin with #8 x 1-5/8"screw. e. Locte four screw holes on the inside of the strgl ody. Insert four #8 x 1" screws into these holes to secure the strgl to the door pnel. 3
4 STEP 3: CONFIRM PUSH BUTTON OPERATION Upper Bolt shown Upper Bolt shown Screws to loosen Finger Grip Push Button. Press the push utton on the upper nd lower olts to ensure the olt pin is properly engged. STEP 4: SIZE AND INSTALL TRIM STRIP Before you instll: Ensure the upper nd lower olts re in the retrcted position. Ensure the seling fin on the trim is on the side closest to the wetherstrip. Seling Fin on Trim Strip Wetherstrip (gry to show contrst). Retrct the olt y pulling the finger grip ck. If retrcting the olt is tight on the upper olt, loosen the screws on the upper olt sleeve. OVERVIEW OF TRIM STRIP INSTALLATION 2. Align Cutouts 3. Cut trim strip to size X 1. Mesure X nd Y To instll: 1. Mesure nd note the distnce from the dedolt crossore to the top of the strgl (X) nd the distnce from the ottom olt sleeve to the strike crossore (Y). 2. Align the D-shped cutout on the trim strip with the push uttons on the upper/ lower olt. 3. Cut the trim strip to fit etween ech component (See imge for detils.). Dedolt Crossore Strike Crossore Y 4
5 STEP 4 (CONT.): SIZE AND INSTALL TRIM STRIP UPPER TRIM STRIP: ALIGN CUT AND INSTALL (X -1-1/8")! The seling fin on the trim strip should e ligned closest to the wetherstrip for the est performnce.. Align the D-shped cutout on the trim with the push utton on the upper olt. If there is n overhng pst the top of the upper olt, cut the trim strip to fit flush with end of the strgl. LOWER TRIM STRIP:. Keeping the cutout ligned, mesure X-1-1/8" nd cut the trim strip. Instll sized trim strip into the strgl ody. MIDDLE TRIM STRIP: ALIGN CUT AND INSTALL CUT AND INSTALL c d e (Y -1-1/8") c. Align the D-shped cutout on the trim strip with the push utton on the lower olt. If there is n overhng with the lower olt sleeve, cut excess trim strip. d. Instll the sized trim strip on the lower hlf of the strgl with the seling fin on the side closest to the wetherstrip. e. Mesure the distnce etween the strike nd dedolt retiner. Cut the remining trim strip to mtch this length nd instll into the strgl. 5
6 STEP 5: INSTALL OPTIONAL SECURITY FLANGE (OUTSWING ONLY) Active Door Pnel. Position the security flnge on the ctive door pnel with the wide flnge fcing the outside of the house. Peel the tpe cking nd secure ginst the ctive pnel. Active Door Pnel. Insert the screws through the predrilled holes to secure the flnge snug ginst the fce of the ctive door pnel. Inside Outside Top View Security flnge 6
Ultimate Flip Lever Astragal Prehanger Installation Instructions
Ultimte Flip Lever Astrgl Prehnger Instlltion Instructions Tools Required: Flthed Screwdriver Shers Phillips Screwdriver Tpe Mesure Kit Includes: Full Astrgl Full Length Trim Strip Screw Pck Field Pck
More informationUltimate Trilennium Astragal Prehanger Installation Instructions
Ultimte Trilennium Astrgl Prehnger Instlltion Instructions Tools Required: Flthed Screwdriver Shers Phillips Screwdriver Power Drill with 1" Drill Bit Tpe Mesure 1" Spde Bit Kit Includes: Full Astrgl Full
More informationMulti-Point Astragal Prehanger Installation Instructions
Multi-Point Astrgl Prehnger Instlltion Instructions 8817 West Mrket Street Colfx, NC 27235 800.334.2006 www.endurproducts.com Tools Required: Endur Router Templte (or equivlent) Router with 5/8" dimeter
More informationNORTH STAR 2-PANEL PATIO DOOR ASSEMBLY INSTRUCTIONS
40684 Talbot Line, St. Thomas, Ont., N5P 3T2 Phone: (59) 637-7899 Toll Free: (800) 265-570 Fax: (59) 637-3403 Web Site: www.northstarwindows.com NORTH STR 2-PNEL PTIO DOOR SSEMBLY INSTRUCTIONS I:\PDssembly\2Panel\CovPg.doc
More information* * 33/3549A CS 33/3549A. 2-Point Latch includes these additional parts. 1-Point Latch (LBL) Customer Service. Installation Instructions
*23970726* 23970726 33/3549A CS 33/3549A Instlltion Instructions This instruction covers new instlltion of the 33/3549A conceled verticl device for luminum nd hollow metl doors. RF Also covered is the
More informationNORTH STAR 4-PANEL PATIO DOOR ASSEMBLY INSTRUCTIONS
40684 Talbot Line, St. Thomas, Ont., N5P 3T Phone: (519) 637-7899 Toll Free: (800) 65-5701 Fax: (519) 637-3403 Web Site: www.northstarwindows.com NORTH STR 4-PNEL PTIO DOOR SSEMLY INSTRUCTIONS (JN/P-Dr04/4Panssy
More informationRETRACTABLE SCREEN ASSEMBLY AND INSTALLATION INSTRUCTIONS. SINGLE OUTSWING (Retro) / (Full-Size) STEP 1: REVIEW & CHECK FIG.
STEP 1: REVIEW & CHECK ) CONFIRM DOOR HEIGHT & WIDTH You have purchased a SINGLE Retractable Screen for an INSWING door. HEIGHT: This unit is available in two sizes: Retro and Full-Size. Please make sure
More informationFOR DEVICES SOLD PRIOR TO
23970734 98/9949 CS 98/9949 FOR DEVICES SOLD PRIOR TO 8-10-16 This instruction covers new instlltion of the 98/9949 conceled verticl device for hollow metl nd luminum doors. RF Instlltion Instructions
More information670 Freestyle/Style Door with In-Line Panel
M 670 Freestyle/Style oor with In-Line Pnel Style Series Option Metl HK87 Slide MGNETIC PULL HNLE KIT with Mgnet Vinyl 083 JM E 989 MGNETIC OOR STOP N H900 PN HE SCREW C (CUH or MG) 781 HEER 716 HEER /
More informationEndura All-Aluminum Z-Articulating Cap Sill Retrofit Kit for French Doors
Endura All-Aluminum Z-Articulating Cap Sill Retrofit Kit for French Doors Installation Instructions Before You Begin: This retrofit kit is designed for the Endura Z-Series All- Aluminum sill. Please ensure
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS Multi Line 6 x8 255x193x203cm / 100 1 /2 x76 x80 Poly-Tex, Inc. PO Box 458 27725 Dnville Avenue Cstle Rock, MN 55010 We Site: www.poly-tex.com English - 69717 Hoy Greenhouse Service
More informationRETRACTABLE SCREEN ASSEMBLY AND INSTALLATION INSTRUCTIONS. DOUBLE INSWING (Retro) / (Full-Size) FIG. 1A STEP 1: REVIEW & CHECK FIG.
STEP 1: REVIEW & CHECK ) CONFIRM DOOR HEIGHT & WIDTH You have purchased a DOUBLE Retractable Screen for an INSWING door. HEIGHT: This unit is available in two sizes: Retro and Full-Size. Please make sure
More informationLEXUS IS250/IS350 FRONT SPOILER Section I - Installation Preparation. Part Number: Section I - Installation Preparation.
Section I - Instlltion Preprtion Prt Numer: 0854-53830 Section I - Instlltion Preprtion Kit Contents 3 Description Front spoiler Hrdwre g Instruction mnul Additionl Items Required For Instlltion Conflicts
More informationINOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS
INOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.
More information* * 98/9949 CS 98/ Point Latch includes these additional parts. 1-Point Latch (LBL) Customer Service. Installation Instructions
*23970734* 23970734 98/9949 CS 98/9949 Instlltion Instructions This instruction covers new instlltion of the 98/9949 conceled verticl device for hollow metl nd luminum doors. RF Also covered is the CS
More informationCanopy Bed Frame. Date: 8 Jun 15 www. potterybarn.com Page 1 of 12 Rev:
Cnopy Bed Frme Dte: 8 un 15 www. potterybrn.com Pge 1 of 12 Importnt Sfety Instructions: WARNIN: Do not llow children to climb on, pull on, or hng from cnopy. Filure to follow these instructions cn result
More information2012+ F30 320i, 328i F22 228i Carbon Fiber S-FLO Intake INSTALLATION GUIDE FOR RACING USE ONLY
PERFORMNCE ENGINEERING FOR EUROPEN UTOS INSTLLTION GUIDE 2012+ F30 320i, 328i 2014+ F22 228i Carbon Fiber S-FLO Intake FOR RCING USE ONLY Congratulations on your purchase of the WE Tuning Carbon Fiber
More information463-GP. Swing Door. Technical Assistance is available Monday - Friday, 8:00 a.m. - 5:00 p.m. (Central Time) (Toll Free) 463-GP 5/06
463-GP Swing Technical ssistance is available Monday - Friday, 8:00 a.m. - 5:00 p.m. (Central Time) 1-877-723-7190 (Toll Free) PRTS LIST FRME PCKGE KEY DESCRIPTION PRT QTY SILL 855 1 JM 942 2 E MGNETIC
More informationThe Genius Sierra retractable screen features a fully assembled screen cassette pre-sized for
IT IS IGLY REOENDED TT TE INSTRUTIONS E RED TROUG EFORE INSTLLTION. RETRTLE SREEN DOOR SIERR 100 SINGLE DOOR installation instructions INSTLLTION TOOLS Phillips Screwdriver measuring tape and-eld or Power
More informationINSTALLATION & OPERATION INSTRUCTIONS LEVER HANDLE LOCKSETS.
INSTALLATION & OPERATION INSTRUCTIONS FOR LEVER HANDLE LOCKSETS 999-00333E_EN FOR BRINKS HOME SECURITY INTERIOR LOCKING & NON-LOCKING LEVER HANDLE LOCKSETS. FITS DOORS 1-3/8" (35 mm) TO 1-3/4" (45 mm)
More informationARK CHEVRON INSTALLATION GUIDE
ARK CHEVRON INSTALLATION GUIDE THANK YOU FOR YOUR PURCHASE OF DUCHÂTEAU WALL COVERINGS. We recommend you hire n experienced finish crpenter or wood flooring instller to chieve qulity results with ll DuChâteu
More informationCongratulations! You are now on your way to enriching your life with!
C) Using the base point as your reference, measure up 8-1/32 and mark a horizontal line. Measure in from the edge of the door the distance of your backset and mark where the two lines cross. This will
More informationRim-Lock Door Set Installation Instructions
Rim-Lock Door Set Installation Instructions Let s get started Check Your Parts List Two Doorknobs with Set Screws B. Doorknob Spindle C. Rim Lock with Mounting Screws D. Keeper with Mounting Screws E.
More informationSeries Door with In-Line Panel (GIH / AHD)
600 7000 Series oor with In-Line Pnel (GIH / H) H900 P H 083 JM C 781 HR 716 HR / SILL ISRT H900 P H F H170 MGTIC STRIP H900 P H 083 JM H5195 STTIG LOCK VRTICL VIYL GLZIG X Y Z HORIZOTL VIYL GLZIG FRM
More information2300 BI-FOLD INSTALLATION GUIDE
2300 BI-FOLD INSTALLATION GUIDE INSTALLATION INSTRUCTIONS OF MAIN FRAME Header #8 x 2½ zinc coated screws 2 1 2 Jamb Jamb 1 1 3 #8 x 2½ zinc coated screws 4 1 4 3 #8 x 2½ zinc coated screws 5 Threshold
More informationInstalling Your Electronic Deadbolt
Ultra Security Plus Electronic Deadbolt Installation Instructions http://www.hberger.com/video-gallery/electronic-deadbolt New Installation Lock Location Preparation (Skip this section if you door has
More informationINOVO 2-LITE SLIDING PATIO DOOR
INOVO 2-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.
More informationPet Door Panel Installation Manual
Pet Door Panel Installation Manual 400-558-1 1 4/3/03, 3:26 PM Components: Pet Door Panel Panel Latch Assembly Foam Weather-stripping Glass Sweep (4) Binding Posts (6) #6 x 1/2 Sheet Metal Screws (4) 8-32
More informationInstallation Instructions
by Precision Screen & Security s 27040 San Bernardino Ave, Redlands, CA 92374 www.precision-screens.com TM Installation Instructions NOTE: Prior to Permanently mounting the BacTrac, insure the handle and
More informationMORTISE LOCK INSTALLATION INSTRUCTIONS
MORTISE LOCK INSTALLATION INSTRUCTIONS INSPIRE TM ROSELESS DESIGNER TRIM FM 340 Rev. 10/18 TABLE OF CONTENTS: DOOR PREPARATION 1 ML2000 LOCK HANDING 2 FULL WORKING TRIM (STD) 3 HALF WORKING TRIM (M30)
More informationOVERVIEW. Mounting Post (2 places) Cylinder Cam. Handing Pin
DEVICES COVERED IN THIS DOCUMENT: 46CE Cylinder Escutcheon Key locks and 46DT Dummy Trim Pull when dogged unlocks lever 46BE Blank Escutcheon Always operable 46NL Night Latch Key retracts latchbolt 46NK
More informationPlease Do Not Return Product to Store!
Instlltion Guide for ndersen Luminire Retrctble Insect Screen Door with Slidewy Insect Screen System Designed for 6 wide by 80 tll single hinged doors with suitble mounting surfce. For instlltion help
More informationAssembly Instructions
10' and 12' Octagon Cedar Gazebo Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 06/20/09 Cedar Gazebo Assembly Instructions
More informationUPTOWN CANOPY FRAME T/F/Q
UPTOWN CANOPY FRAM T/F/Q Dte: 30 Mr 16 www.pbteen.com Pge 1 of 12 mportnt Sfety nstructions: Plese red ll instructions crefully before ssembling. For your sfety, ssembly by two or more dults is strongly
More informationET 51 EXTERIOR ROOF DRIP SIDE FINISH MOULDING INSTALLATION
EXTERIOR ROOF DRIP SIDE FINISH MOULDING 51 INSTALLATION The procedure descried elow is for the LH side. Use the sme procedure for oth the RH nd LH sides, unless otherwise specified. 1. INSTALL ROOF SIDE
More informationCongratulations! You are now on your way to enriching your life with! Figure #5. Step 5 Install the Dummy Deadbolt. Step 3 Drill the Door
C) Using the base point as your reference, measure up 8-1/32 and mark a horizontal line. Measure in from the edge of the door the distance of your backset and mark where the two lines cross. This will
More information* * 98/9949WDC. 1-Point Latch (LBL) 2-Point Latch includes these additional parts. Customer Service
*24017501* 24017501 Coneled Vertil Devie for Wood Doors 98/9949WDC Instlltion Instrutions 1-Point Lth (LBL) 2-Point Lth inludes these dditionl prts NOTE: If door does not hve utout for ling inside lok
More informationAssembly Instructions Nevins Phone Booth
Assembly Instructions Nevins Phone Booth Included Hardware Tools Required supplied by installer Drill & Bit Bolt A - (16) 1/4-20 x 1-1/2 hex head Bolt B - (20) 1/4-20 x 2-1/2 phillips head Screw 1 - (24)
More informationEntry Mortise Lock Set Lever to Lever
Entry Mortise Lock Set Lever to Lever 1 Lever 2 Escutcheon 3 Turn Piece 4 Mortise Lock 5 Scalp 6 Mortise Lock Strike 7 Mortise Lock Dust Box 8 Mortise Cylinder 9 Cylinder Swing Cover 10 Spindle 11 Spindle
More informationINSTALLATION INSTRUCTIONS REPLACING EXISTING DEADBOLT ASSEMBLY
INSTALLATION INSTRUCTIONS REPLACING EXISTING DEADBOLT ASSEMBLY A B C L M N D E F G O P Q H I J Tools provided in Amesbury installation kit: (A) door router fixture, (B) doorframe router fixture, (C) ½
More informationINSTALLATION GUIDE 2009-CURRENT HUMMER H3T PRODUCT CODE:
INSTALLATION GUIDE 2009-CURRENT HUMMER H3T PRODUCT CODE: 268 June 22, 2010 TOOLS NEEDED COMPONENTS INCLUDED P2 Tip 3/8" Drill Rubber Gasket(s) x 2 Bracket(s) x 2 1/2" Drill Bit Bulkhead Flange #2 Phillips
More information620 Freestyle/Style Swing Door
620 Freestyle/Style Swing Door (CUH or MG) Style Series Option M HK87 MGNETIC PULL HNDLE KIT 989 MGNETIC DOOR STOP C 083 JM Metal Slide with Magnet H900 PN HED SCREW N Connector Screw J HTG6 PUSH / PULL
More information3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS
3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation. TOOLS NEEDED: Tape Measure
More informationAssembly Instructions 10 X 10 Aluminum Frame Building
Assembly Instructions 10 X 10 Aluminum Frame Building 27 97 9 8 47 36 74 52 10 10 X 10 Square Building W/ Dome Includes: The Steel Entry Door with a Dead Bolt Lock assembly and Aluminum Door Frame. Metal
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BUILDERS CHOICE FRAMED Shower Height Swing Door Model: L533 Rev. 09.03.13 MAINTENANCE: Two primary materials are used to manufacture your new Aquatic enclosure; tempered glass
More informationDouble Screen Door Installation Instructions
Double Screen Door Installation Instructions (36) #8x1 tek screws (20) #8x1/2 tek screws Package Includes: (2) PCA Screen Doors (1) Astragal (1) Left Hand Z-bar (1) Right Hand Z-bar (1) Header Z-bar (2)
More informationDoor Hardware Installation Instructions. Version A No Interior on an Un-prepped Door Step 1 Select the Position of the Handleset
For Assistance Call: 1-800-522-7336 8 am - 5 pm, Monday - Friday, MST or visit our Website at: www.grandeur-nw.com Door Hardware Installation Instructions Dummy Handleset Optional Rosette (Round) Interior
More information4. Partially open the operating panel and tilt the top toward the interior of the door (Figure 4). Lift the panel off the sill and set it aside.
Effective Date: 10/1/2017 Tools Needed Kit Contents Hardware Kit Safety Glasses Cordless drill Phillips screw bit Two-step drill bit (3/8-1/8 ) utility knife Interior Mullion Exterior Mullion Cover clamps
More informationASSEMBLY INSTRUCTIONS 5PC Storage Dining Set
ASSEMLY INSTRUTIONS 5P Storge Dining Set Sers Stock # 56170 VL Stock #07-2204 U S T O M E R S E R V I E I N F O R M AT I O N Victory Lnd Group, Inc 1350 Munger Rd rtlett, IL 60103 WE: http://www.victorylndgroup.com
More informationTravel Trailer Latch With Dead Bolt Trailer Latch With Dead Bolt. U.S. Patent No. 5,927,773
60-250 Travel Trailer Latch With Dead Bolt 60-251 Trailer Latch With Dead Bolt Service Manual (Installation and Troubleshooting) U.S. Patent No. 5,927,773 CONTENTS 1. BASIC COMPONENTS 2. INSTALLATION OF
More informationPanel Installation Instructions (Revised 2/26/10) (Page 1 of 7)
Panel Installation Instructions (Revised /6/0) (Page of 7) Remove Hanger Frame Topcap by depressing tabs inside top slot of hanger frame and lifting up. Hold panel flush and in a STRIGHT LINE (80 degrees
More informationOtter Pro XT Cottage Installation and Set-Up Instructions
Otter Pro XT Cottage Installation and Set-Up Instructions Otter Pro XT Cottage Fits Small Ultra-Wide Otter Pro and Otter II Sled Only Parts Identification and Check List MODEL NUMBERS: Complete Pkg Pro
More informationBushwacker Jeep Flat Style Fender Flares Rear Pair (JK Wrangler 2dr)
Bushwacker Jeep Flat Style Fender Flares Rear Pair (JK Wrangler 2dr) Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4
More informationAssembly Instructions Nevins Phone Booth
Assembly Instructions Nevins Phone Booth Included Hardware Tools Required supplied by installer Drill & Bit Socket Wrench Bolt A - (16) 1/4-20 x 1-1/2 hex head Bolt B - (20) 1/4-20 x 2-1/4 phillips head
More informationVACUSEAL MODEL 200. HOT TUB PRODUCTS 233 Carrington Road Bethany CT
VACUSEAL MODEL 200 J G F G H L HOT TUB PRODUCTS 233 Carrington Road Bethany CT 06524 860-469-2580 www.vacusealcoverlift.com www.hottubproducts.com Made in USA H K E D C I A P B 10 9 8 7 6 5 4 3 2 1 0 SPAS
More informationThe Useless Machine. Parts Only - Build Guide v0001
TM The Useless Machine Parts Only - Build Guide v0001 For the best outcome, follow each step in order. We recommend reading this guide entirely before you get started. Tools required: One phillips screwdriver,
More informationFitting & User Instructions
Issue 03 Alexnder Universl Furniture Risers Note: These frmes require the ddition of n ttchment. (See pges 4 - ) Bse Frme Mrk Bse Frme Mrk Fitting & User Instructions These instructions pply to the rising
More information1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A
1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com
More information10 Octagon Cedar Gazebo Assembly Instructions
10 Octagon Cedar Gazebo Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 06/22/09 10 Cedar Gazebo Assembly Instructions
More informationSSRLS-3 / SSRLU-3 Installation Instructions
5mm Hex Nut Upper Telescoping hannel & Screws Packing List QTY. ITM 1 Top Telescoping hannel 1 ottom Telescoping hannel w/ self drilling screw 15" 18" 1 Top and ottom Rod with connecting arm 25-½ 2 ¼ -
More informationShetland Stalls Installation Instructions
Shetland Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 1/9/18 Before you start Kit can accommodate up to 12 wide stall front
More informationINSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET
HIGH EDGE 2 1/4"(57mm) 03079400070 INSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET IMPORTANT: THIS LOCK IS NON-HANDED. LOCK IS FACTORY PACKED PREADJUSTED FOR 1³ ₄" (45mm)
More informationFor installation assistance, contact SARGENT at DOORS SHOWN HERE SWING IN FOR ILLUSTRATION PURPOSES ONLY.
SARGENT Installation Instructions for LP8600 x LR8600 & 12-LP8600 x 12-LR8600 Series Low Profile Panic and Fire Exit Devices on Double Egress & Double Doors or LS8600 & 12-LS8600 Low Profile Exit Device
More informationUNIT No FRAMELESS PIVOT SHOWER DOOR
INSTALLATION INSTRUCTIONS UNIT No. 3600 FRAMELESS PIVOT SHOWER DOOR NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) Monday - Friday 8:00 A.M. - 4:30 P.M. Eastern Time QCI0020 Rev. 3 Page 1 of 8
More informationVYTEX PREMIUM SLIDING GLASS DOOR. Table of Contents. Precautions and Safety 2. Tools Required...3. Inspect and Prepare Door...4
VYTEX PREMIUM SLIDING GLASS DOOR Table of Contents Precautions and Safety 2 Tools Required...3 Inspect and Prepare Door...4 Hardware and Parts Check List....4 Master Frame Assembly 5 Master Frame Installation..7
More information846-GP. Neo-Angle Enclosure. Technical Assistance is available Monday - Friday 8:00 a.m. - 5:00 p.m. (Central Time) GP 12/05
846-GP Neo-ngle Enclosure Technical ssistance is available Monday - Friday 8:00 a.m. - 5:00 p.m. (Central Time) 1-877-723-7190 PRTS LIST FRME PCKGE KEY ESCRIPTION PRT QTY SILL 855 3 M 942 2 C HEER 101
More information063-GP. Swing Door with In-Line Panel
063-GP Swing with In-Line Technical ssistance is available Monday - Friday, 8:00 a.m. - 5:00 p.m. (entral Time) 1-877-723-7190 (Toll Free) PRTS LIST FRME PGE EY ESRIPTION PRT QTY SILL 855 1 JM 942 2 HEER
More informationSection 3: Understanding Your Shop Drawings Reading Shop Drawing Abbreviations 60" O.A. stands for the overall dimension from the back wall to the front face of achieve your 60" overall you will set the
More informationPassage Mortise Lock Set Lever to Lever
Passage Mortise Lock Set Lever to Lever 1 Lever 2 Escutcheon 3 Mortise Lock 4 Scalp 5 Mortise Lock Strike 6 Mortise Lock Dust Box 7 Spindle 8 Spindle Spring 9 Spindle Retainer 2 1 9 8 7 9 7 8 3 1 2 4 5
More informationRH-412 STEEL DOORS INSTALLATION INSTRUCTIONS
RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side.
More informationStair Mounting Kit. Installing safety gates in modern homes can be very challenging, especially for stairs.
Stair Mounting Kit Installation Guide Installing safety gates in modern homes can be very challenging, especially for stairs. The Stair Mounting Kit will allow you to mount gates to most square and round
More informationPacking List MODEL TEL-IAL-481 For Inactive Leaf TRIDENT double door
Items: SECURITECH GROUP, INC. MP uxiliary POLICE LOCK Packing List MODEL TEL-IL-481 For Inactive Leaf TRIDENT double door Items with * are pre-installed or assembled Fasteners: Part# Qty Name Description/Usage
More informationCANOPY SYSTEMS PAGE 1 OF 14
NOPY SYSTEMS PGE 1 OF 1 SY 092 I N S T L L T I O N I N S T R U T I O N S RED REFULLY! minimum of of two persons are required to install canopies. Do not step on base shelves... to avoid damage:. Do not
More informationAssembly Instructions
Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt
More informationINSTALLATION INSTRUCTIONS RH 412 STEEL DOORS
By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side. Note: Having the hood open makes the job
More informationVinyl Sliding Glass Door Assembly Instructions
Vinyl Sliding Glass Door Assembly Instructions SERIES SGD 5470/5570 Para instrucciones en español, visite: http://bit.ly/pgtassemblyinstructions Parts List ITEM 4 5 6 7 8 9 0 4 5 6 7 8 SGD 5470/5570 PARTS
More informationMISCELLANEOUS CABINET REPAIRS
MISCELLANEOUS CABINET REPAIRS 167 168 NOTES MISCELLANEOUS CABINET REPAIRS Cabinet Panel Repairs 175 SIDE PANEL REPLACEMENT - GDM SERIES INSTALLATION INSTRUCTIONS Tools Required 1/8" drill Rivet Tool Silicone
More information4-lite Patio Door. Installation Instructions
4-lite Patio Door Installation Instructions IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation. Note: Only the 5-0 x 6-8
More information713C-GP. Pivot Door. Technical Assistance is available Monday - Friday, 8:00 a.m. - 5:00 p.m. (Central Time) (Toll Free) 713C-GP 8/06
713C-P Door Technical Assistance is available Monday - Friday, 8:00 a.m. - 5:00 p.m. (Central Time) 1-877-723-7190 (Toll Free) PARTS IST FRAME PACKAE KEY DESCRIPTION PART QTY A SI A195 1 PIVOT JAM A196
More informationNOTE THAT THE HANDLE IS BELOW THE LOCK BASE
NOTE THT THE POSITION OF STOP IS LOCTED USING THE SINGLE HOLE S PLCEMENT GUIDE. NOTE THT THE HNDLE IS ELOW THE LOCK SE DETIL G SCLE.5. OF CHNGE DTE SIGN RELESED FOR PRODUCTION // RQ G SEE SHEET 3 FOR P/N
More informationLOCK ASSEMBLY INSTRUCTIONS
LOCK ASSEMBLY INSTRUCTIONS Use the drawing below as a key to determine which lock assembly instruction to follow. There are three different types of locks used, and the instructions for each are on the
More information13MM FLAT WRENCH FOR LEVELING THE GLIDES OF STRUCTURE 6MM ALLEN KEY FOR ROOF CLIPS PHILLIPS HEAD BIT FOR SCREWS FOR DOOR FRAME
1 TOOLS REQUIRED: MOVING CART/DOLLY FOR TRANSPORTING PANELS, ROOF, AND POSTS TWO 9 FT. STEP LADDERS FOR INSTALLING ROOF & PANELS REVERSIBLE RATCHET 1/4 DRIVE FOR CORNER SCREWS ON TOP TRAVERSE BEAMS ALTERNATIVE
More informationGE Monogram. Installation. Instructions. Microwave Oven. Under Cabinet Installation. and. JX827 Series Built-In Kit. Models.
GE Monogram Installation Instructions Under Cabinet Installation and JX827 Series Built-In Kit Models ZEM200 Series CAUTION WARNING Before you begin Read these instructions completely and carefully. IMPORTANT:
More informationOctagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models
Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 04/29/09 Vinyl Gazebo Assembly
More informationTubing Spacers. Backing Plate. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a a. a a. a a
Grnd Slm Instlltion Instructions TACO Metls Inc., 98 NE 179th Street Mimi, Florid 33162 hndyhnk@tcomrine.com tcomrine.com This Box Contins: 1- Port side Grnd Slm 1- Strbord side Grnd Slm 4-5/16 x 1 stinless
More informationSliding Glass Door Assembly and Installation Guide
Sliding Glass Door Assembly and Installation Guide Index Door System Components and Hardware The following components are needed to complete the installation of your Sliding Patio Door unit. Check all
More informationShepherd 210A Fingerprint Door Lock Installation Manual V1.1
Shepherd 210A Fingerprint Door Lock Installation Manual V1.1 Hongda USA Inc. 2505 Technology Dr. #2-6A, Hayward, CA 94545, USA Phone: (510) 887-5682 Fax: (510) 372-0487 Email: info@hongdausa.com Website:
More informationINSTRUCTION BOOKLET #C21. For Wallbed models: KING SIZE
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT
More informationInstallation Instructions Model # TEL-100 / 200 Manual Locking or Self Locking
INSTLLTION INSTRUTIONS TL-100 / 200 GSS-oors TL 1-406-212-2334 MIL rg@gssdoors.com W www.gssdoors.com GSS oors (406) 212-2334 (406) 897-2121 rg@gssdoors.com www.gssdoors.com TM Multi-Point eadbolt Installation
More informationPremium Double Security Screen Door Kit Installation Instructions
4 3 2 6 5 4 3 2 1 dvanced Screen Systems Surface Mount Premium Double Security Screen Door Kit Installation Instructions DISREGRD INSTRUCTIONS INCLUDED WITH DOOR PNELS Read completely through the kit installation
More informationInstallation and Assembly: Flat Panel Pull-out Swivel Wall Mount
Installation and ssembly: Flat Panel Pull-out Swivel Wall Mount Models: SP850-V2X2 2300 White Oak Circle urora, Il 60502 (800) 865-2112 Fax: (800) 359-6500 www.peerlessmounts.com ISSUED: 01-17-12 SHEET
More informationBlock Frame Inovo Patio Door/Transom/Sidelite Field Mulling Instructions. simonton.com/installation. If mulling sidelites, skip to Step 5.
Effective Date: 10/1/17 Tools Needed Kit Contents Safety Glasses Cordless Drill Phillips Screw Bit Two-step Drill Bit (3/8-1/8 ) Utility Knife Interior Mullion Exterior Mullion Cover Hardware Kit Clamps
More informationhttps://www.wallbedsbywilding.com/wallbed-installation-studio-series/
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More informationFold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE
Fold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE This instruction guide provides the minimum recommended procedures to correctly prepare the rough opening, install a fold-a-way patio door unit and apply
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS TOOLS REQUIRED Rechargeable, variable speed drill 3/8 diameter drill bit 3 Robertson bits #0, #1 and #2 Slot screwdriver Non marring hammer with 1 head Level Caulk or sealant
More informationPontiac Grand Am SC/T Installation Instruction Sheet Aftermarket Front Fascia
Aftermarket Front Fascia be used correctly to install the secondary fascia to the existing fascia. 1 Fascia Front 5 Bolt M6-1.0x60 5 Washer 1/4x9/16 2 Bolt/Washer Assembly 1 Nut/Washer Assembly 1. Six
More informationReplacing the Reciprocator on an SWF Multi-head.
Replacing the Reciprocator on an SWF Multi-head. Follow the instructions below to replace the reciprocator in the SWF multi-head machines. The tools required are found in the tool kit that came with the
More informationYour combination is and is not recorded at the factory. This number can be found on the combination slides if required.
3778 South Kalamath Street, Englewood, CO 80110 Phone (303) 762-7373 Fax (303) 484-4070 www.presomatic.com office@presomatic.com Installation Instructions for Deadlatch Models 8200 8200A Congratulations
More informationDRAWING TABLE SYSTEM
DRWING TBLE SYSTEM DT31, DT61S, & CDTC71 MODEL VIEWS MY NOT REPRESENT EXCT MODEL PURCHSED : : CRETED NME THIS DRWING IS THE SOLE PROPERTY OF DIVERSIFIED WOOD CRFTS. IT MY NOT BE LTERED OR CHNGED WITHOUT
More informationBushwacker Jeep Flat Style Fender Flares Front Pair
Bushwacker Jeep Flat Style Fender Flares Front Pair Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4 Hours Tools Required:
More information