Low-Voltage, 1 Ω Dual SPST Analog Switch with Power-Off Isolation. Description
|
|
- Dora Clarke
- 5 years ago
- Views:
Transcription
1 FS1259 Low-Voltage, 1 Ω Dual SPST nalog Switch with Power-Off Isolation Features Power-Off Isolation (V CC =0 V) 1 Ω On Resistance (R ON ) for 4.5V V CC 0.25 Ω Maximum R ON Flatness for 4.5 V V CC Space-Saving, US8 Surface Mount Package Broad V CC Operating Range: 1.65 V to 5.50 V Fast Turn-On and Turn-Off Times Break-Before-Make Enable Circuitry pplications Cellular Phone Portable Media Player PD Ordering Information Part Number Top Mark Operating Temperature Range FS1259K8X C to +85 C Description pril 2014 The FS1259 is a high-performance, dual, Single-Pole / Single-Throw (SPST) analog switch. The device features ultra-low R ON of 1 at 4.5 V V CC and operates over the wide V CC range of 1.65 V to 5.50 V. The FS1259 allows for reduced input thresholds on the select pins. The device is fabricated with sub-micron CMOS technology to achieve fast switching speeds and is designed for break-before-make operation. Package 8-Lead US8, JEDEC MO-187, Variation C, 3.0 mm Wide Packing Method 3000 Units Tape and Reel FS1259 Low-Voltage, 1 Dual SPST nalog Switch with Power-Off Isolation 1 1B V CC 1S 2S 3 6 2B Figure 1. nalog Symbols FS1259 Rev
2 Pin ssignments Pin Definitions 1 1B 2S Vcc 1S 2B 2 Figure 2. Pin ssignments (Top View) Pin # Name Description 1 1 Data Port 2 1B Data Port 3 2S Control Input 4 Ground 5 2 Data Port 6 2B Data Port 7 1S Control Input 8 V CC Supply Voltage Truth Table Control Input (S) Function LOW Disconnected HIGH Connected to B FS1259 Rev
3 bsolute Maximum Ratings Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameter Min. Max. Unit V CC Supply Voltage V V SW Switch Voltage (1) -0.5 V CC V V IN Input Voltage (1) V I IK Input Diode Current -50 m I SW Switch Current (Continuous) 200 m I SWPEK Peak Switch Current (Pulsed at 1 ms Duration, <10% Duty Cycle) 400 m P D Power Dissipation at 85 C 3.0 µw T STG Storage Temperature Range C T J Maximum Junction Temperature +150 C T L Lead Temperature (Soldering, 10 seconds) +260 C ESD Human Body Model (JEDEC: JESD22-114) 8000 V Charged Device Model (JEDEC: JESD22-C101) 2000 V Machine Model (JEDEC: JESD22-115) 350 V Note: 1. The input and output negative ratings may be exceeded if the input and output diode current ratings are observed. Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to bsolute Maximum Ratings. Symbol Parameter Min. Max. Unit V CC Supply Voltage V SEL Control Input Voltage (2) 0 V CC V V SW Switch Input Voltage 0 V CC V T Operating Temperature C J Thermal Resistance, Still ir 215 C/W Note: 2. Control Input must be held HIGH or LOW; it must not float. FS1259 Rev
4 Electrical Characteristics ll typical values are at 25 C unless otherwise specified. Symbol Parameter V CC (V) Conditions V IH V IL I IN I NO(0FF) I NO(On) Input Voltage High Input Voltage Low Control Input Leakage Off-Leakage Current On-Leakage Current of Port B T =+25 C T =-40 to +85 C Unit Min. Typ. Max. Min. Max to to to to to to to to V IN =0 or V CC V IN =0 or V CC V IN =0 or V CC V IN =0 or V CC =1 V, B=4.5V or B=4.5 V, = 1V =1 V, B=3.0 V or B=3.0 V, =1 V =0.5 V, B=2.3 V or B=2.3, =0.5 V =0.3 V, B=1.65 V or B=1.65, =0.3 V =Floating; B=4.5 V, 1 V =Floating; B=3.0 V, 1 V =Floating; B=2.3 V, 0.5 V =Floating; B=1.65 V, 0.3 V =1 V, 4.5 V; B=Floating V V n n n I (ON) On-Leakage Current of Port 3.60 =1 V, 3.0 V; B=Floating =0.5 V, 2.3; B=Floating n 1.95 =0.3 V, 1.65 V; B=Floating I OFF Power Off Leakage Current of Port & Port B 0 =0 to 5.5 V; B=0 to 5.5 V µ FS1259 Rev
5 Electrical Characteristics (Continued) ll typical values are at 25 C unless otherwise specified. Symbol Parameter V CC (V) Conditions R PEK R ON R ON R FLT(ON) Peak On Resistance Switch On Resistance (3) On Resistance Matching Between Channels (4) On Resistance Flatness (5) B or 2B=0 to V CC 1B or 2B=0 to V CC I OUT =-8 m, 1B or 2B=0 to V CC I OUT =-2 m, 1B or 2B=0 to V CC 1B or 2B=2.5 V 1B or 2B=2.0 V I OUT =-8 m, 1B or 2B=1.8V I OUT =-2 m, 1B or 2B=1.5 V 1B or 2B=2.5 V 1B or 2B=2.0 V I=-8 m, 1B or 2B=1.8 V I OUT =-2 m 1B or 2B=1.5 V 1B or 2B=1.0 V, 1.5 V, 2.5 V 1B or 2B=0.8 V, 2.0 V I OUT =-8 m, 1B or 2B=0.8 V, 1.8 V I OUT =-2 m, 1B or 2B=0.6 V, 1.5 V T =+25 C T =-40 to +85 C Min. Typ. Max. Min. Max T =25, 85 C T =-40 C Unit Ω Ω Ω Ω 5.50 V IN =0 or V CC, I OUT = I CC Quiescent Supply Current 3.60 V IN =0 or V CC, I OUT = V IN =0 or V CC, I OUT = n 1.95 V IN =0 or V CC, I OUT = I CCT Increase in I CC per Control Input 4.5 to 5.5 sel=1.8 V µ Notes: 3. On resistance is determined by the voltage drop between the and B pins at the indicated current through the switch. 4. R ON =R ON maximum R ON minimum; measured at identical V CC, temperature, and voltage. 5. Flatness is defined as the difference between the maximum and minimum value of on resistance over the specified range of conditions. FS1259 Rev
6 C Electrical Characteristics ll typical values are at V CC =1.8 V, 2.5 V, 3.0 V, 5.0 V at 25 C unless otherwise specified. Symbol Parameter V CC (V) Conditions t ON t OFF Q Turn-On Time Turn-Off Time Charge Injection 4.50 to 5.50 OIRR Off-Isolation 1.8 to 5.0 Xtalk Crosstalk 1.8 to 5.0 BW THD -3 db Bandwidth Total Harmonic Distortion T =+25 C Min. Typ. Max. Min. Max to B or 2 B=V CC, R L =50 Ω, 2.30 to 2.70 C L =35 pf to to to to B or 2B=V CC, R L =50 Ω, C L =35 pf to to to to 2.70 C L =1.0 nf, V GEN =0 V, R GEN =0 Ω to f=1 MHz, R L =50 Ω f=1 MHz, R L =50 Ω 4.50 to to R L =50 Ω 2.30 to to T =-40 to +85 C Unit Figure ns Figure 11 ns Figure 11 pc Figure db Figure db Figure 12 MHz Figure R L =600,.003 Figure 16 V IN =0.5 V PP, % f=20 Hz to khz.001 Figure 16 Capacitance Symbol Parameter V CC (V) Conditions C IN Control Pin Input Capacitance 0 C OFF B Port Off Capacitance 1.65 to 5.50 C ON Port On Capacitance 1.65 to 5.50 f=1 MHz Figure 14 f=1 MHz Figure 14 f=1 MHz Figure 14 T =+25 C Min. Typ. Max. Unit 3 pf 21 pf 47 pf FS1259 Rev
7 Typical Performance Characteristics RON (Ohms) R ON (Ohms) Gain (db) C 25 C -40 C V IN (V) R ON (Ohms) C 25 C -40 C V IN (V) Figure 3. On Resistance (V CC =4.5 V) Figure 4. On Resistance (V CC =3.0 V) V IN (V) 85 C 25 C -40 C R ON (Ohms) C 85 C V IN (V) Figure 5. On Resistance (V CC =2.3 V) Figure 6. On Resistance (V CC =1.65 V) Frequency (MHz) Figure 7. Frequency Response (V CC =5.5 V, C L =0 pf) Off Isolation (db) Gain (db) C Frequency (MHz) Figure 8. Frequency Response (V CC =3.3 V, C L =0 pf) THD (%) V CC =1.8V V CC =5.0V Frequency (MHz) Frequency (MHz) Figure 9. Frequency Response (V CC =5.0 V, C L =0 pf) Figure 10. Total Harmonic Distortion FS1259 Rev
8 Test Diagrams V B 1B or 2B S V CC R L 50 C L includes fixture and stray capacitance. 0 or V CC S V CC 50 1B V CC 10nF 2B V OUT C L 35pF Figure 11. V IN V OUT Figure 12. Control Input Switch Output 0V 0V V CC V OUT Turn On / Off Timing MES Network nalyzer % t ON t R = t F = 2.5ns t OFF 0.9 x V OUT 0.9 x V OUT Logic input waveforms inverted for switches that have the opposite logic sense. REF Off Isolation and Crosstalk OFF ISOLTION = 20log V OUT V IN ON-LOSS = 20log V OUT V IN CROSSTLK = 20log V OUT V IN V CC V GEN R GEN 1B or 2B C L V OUT V OUT ΔV OUT In S Off On Off Control Input In Off On Q = (ΔV OUT ) (C L ) Off Figure 13. Charge Injection FS1259 Rev
9 Test Diagrams (Continued) Signal Generator 0dBm V IN Logic Input 0V or V CC 10nF B N S VCC Capacitance Meter f = 1MHz Figure nF V+ 1B or 2B S 0V or V CC On / Off Capacitance Measurement Setup nalyzer Signal Generator 0dBm V IN Logic Input 0V or V CC 10nF B N S V CC R L nalyzer Figure 15. Bandwidth Figure 16. Harmonic Distortion FS1259 Rev
10 Physical Dimensions PIN 1 IDENT SETING PLNE TOP VIEW 0.90 MX SIDE VIEW 0.4 TYP 5 B C B LL LED TIPS LL LED TIPS 0.1 C C (8X) 0.13 B C GGE PLNE (8X) (8X) RECOMMENDED LND PTTERN. CONFORMS TO JEDEC REGISTRTION MO-187 B. DIMENSIONS RE IN MILLIMETERS. C. DIMENSIONS RE EXCLUSIVE OF BURRS, MOLD FLSH, ND TIE BR EXTRUSIONS. D. DIMENSIONS ND TOLERNCES PER NSI Y14.5M, E. FILE DRWING NME : MKT-MB08rev4 DETIL SETING PLNE DETIL Figure Lead US8, JEDEC MO-187, Variation C, 3.0 mm Wide Package Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. lways visit Fairchild Semiconductor s online packaging area for the most recent package drawings: For current packing container specifications, visit Fairchild Semiconductor s online packaging area: FS1259 Rev
11 FS1259 Rev
12 Mouser Electronics uthorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Fairchild Semiconductor: FS1259K8X
FSA1259 / FSA1259A Low-Voltage, 1Ω Dual SPST Analog Switch with Power-Off Isolation
FS1259 / FS1259 Low-Voltage, 1Ω Dual SPST nalog Switch with Power-Off Isolation Features Power-Off Isolation (=0V) 1Ω On Resistance (R ON) for 4.5V 0.25Ω Maximum R ON Flatness for 4.5V Space-Saving, US8
More informationFSA4159 Low-Voltage, 1Ω SPDT Analog Switch with Power-Off Isolation
December 2013 FSA4159 Low-Voltage, 1Ω SPDT Analog Switch with Power-Off Isolation Features Low I CC When the S Input is Lower Than V CC Power-Off Isolation (V CC=0 V) 1 Ω On Resistance (R ON) for 4.5 V
More informationFSA Ω Low-Voltage SPDT Analog Switch
F5157 0.4Ω Low-Voltage PDT nalog witch Features Typical 0.4Ω On Resistance (R ON ) for +2.7V upply F5157 Features Less than 12μ I CCT Current When Input is Lower than 0.25Ω Maximum R ON Flatness for +2.7V
More informationFSA2257 Low R ON Low-Voltage Dual SPDT Bi-Directional Analog Switch
F2257 Low R ON Low-Voltage Dual PDT Bi-Directional nalog witch Features Maximum 1.15Ω On Resistance (R ON ) for 4.5V upply 0.3Ω Maximum R ON Flatness for +5V upply pace-aving MicroPak Packaging Broad Operating
More informationFSA2859 Dual-Voltage, 0.8Ω DPDT Analog Switch with Power-Off Isolation
Click here for this datasheet translated into Chinese! ugust 2008 F2859 Dual-Voltage, 0.8Ω DPDT nalog witch with Power-Off Isolation Features Power-Off Isolation (=0V) 0.8Ω Maximum On Resistance (R ON)
More informationFSA Ω Low-Voltage Dual DPDT Analog Switch
March 2013 FSA2467 0.4Ω Low-Voltage Dual DPDT Analog Switch Features Typical 0.4 On Resistance (R ON ) for +2.7V Supply Features Less then12µa ICCT Current when Sn Input is Lower than V CC 0.25 Maximum
More informationIs Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
More informationFSAV433 High-Bandwidth (550MHz), 3-Channel, 3:1 Video Switch
January 2011 FSAV433 High-Bandwidth (550MHz), 3-Channel, 3:1 Video Switch Features Ground between Channels to Optimize Isolation and Reduce Hostile Crosstalk -70dB Non-Adjacent Channel Crosstalk at 30MHz
More informationAOZ Ω Low-Voltage Dual-DPDT Analog Switch. General Description. Features. Applications AOZ6275
.35Ω Low-Voltage Dual-DPDT nalog witch General Description The OZ6275 is a dual Double-Pole, Double-Throw (DPDT) analog switch that is designed to operate from a single 1.65 V to 4.3 V supply. The OZ6275
More informationAOZ Ω Low-Voltage Dual-SPDT Analog Switch. General Description. Features. Applications
OZ6233 0.35Ω Low-Voltage Dual-PDT nalog witch General Description The OZ6233 is a 0.35Ω low-voltage Dual ingle Pole Double Throw (PDT) analog switch. The OZ6233 operates from a single 1.65V to 3.6V supply.
More informationFSA110 Audio and Wired-OR USB2.0 Hi-Speed (480Mbps) Switch with Negative Signal Capability and Built-in Termination
July 2013 FSA110 Audio and Wired-OR USB2.0 Hi-Speed (480Mbps) Switch with Negative Signal Capability and Built-in Termination Features 6pF Typical Switch Off Capacitance for HS USB 2.5Ω Typical On Resistance
More informationNC7WZ17 TinyLogic UHS Dual Buffer with Schmitt Trigger Inputs
January 2012 NC7WZ17 TinyLogic UHS Dual Buffer with Schmitt Trigger Inputs Features Ultra-High Speed: t PD 3.6ns (Typical) into 50pF at 5 CC High Output Drive: ±24m at 3 CC Broad CC Operating Range: 1.65
More informationFSAT66 Low Voltage Single SPST Normally Open Analog Switch with TTL Compatible Control Input
April 2003 Revised July 2004 FSAT66 Low Voltage Single SPST Normally Open Analog Switch with TTL Compatible Control Input General Description The FSAT66 is a high speed single pole/single throw normally
More informationFSUSB45 High-Speed USB2.0 (480Mbps) Switch with Dedicated Charger Port Detect
July 2013 FSUSB45 High-Speed USB2.0 (480Mbps) Switch with Dedicated Charger Port Detect Features Low On Capacitance: 7.0 pf Typical Low On Resistance: 3.9 Ω Typical Low Power Consumption: 1 μa Maximum
More informationNC7SZ66 Low Voltage Single SPST Normally Open Bus Switch
September 2013 NC7SZ66 Low Voltage Single SPST Normally Open Bus Switch Features Broad V CC Operating Range: 1.65 V to 5.5 V Rail-to-Rail Signal Handling Power Down High-Impedance Inputs/Outputs 5 Ω Switch
More informationFSA321 USB2.0 Hi-Speed (480Mbps) and Audio Switches with Negative Signal Capability and Built-in Termination on Unselected Audio Paths
March 2013 FSA321 USB2.0 Hi-Speed (480Mbps) and Audio Switches with Negative Signal Capability and Built-in Termination on Unselected Audio Paths Features Audio: 1.8 Typical On Resistance HS-USB: 8 Typical
More informationFSUSB30 Low-Power, Two-Port, High-Speed USB 2.0 (480Mbps) Switch
Click to see this datasheet in Simplified Chinese! FSUSB30 Low-Power, Two-Port, High-Speed USB 2.0 (480Mbps) Switch Features Low On Capacitance: 3.7pF (Typical) Low On Resistance: 6.5Ω (Typical) Low Power
More informationFSUSB43 Low-Power, Two-Port, High-Speed, USB2.0 (480Mbps) Switch
FSUSB43 Low-Power, Two-Port, High-Speed, USB2.0 (480Mbps) Switch Features Over-Voltage Tolerance (OVT) on all USB Ports up to 5.25V without External Components Low On Capacitance: 3.7pF Typical Low On
More informationFSUSB22 Low-Power, 2-Port, High-Speed USB 2.0 (480Mbps) Switch
March 2008 FSUSB22 Low-Power, 2-Port, High-Speed USB 2.0 (480Mbps) Switch Features -40dB Off Isolation at 250MHz -40dB Non-adjacent Channel Crosstalk at 250MHz On Resistance: 4.5Ω Typical (RON) -3dB Bandwidth:
More informationNC7SZ57 / NC7SZ58 TinyLogic UHS Universal Configurable Two-Input Logic Gates
NC7SZ57 / NC7SZ58 TinyLogic UHS Universal Configurable Two-Input Logic Gates Features Ultra High Speed Capable of Implementing any Two-Input Logic Functions Typical Usage Replaces Two (2) TinyLogic Gate
More informationFSAV MHz, 4-Channel, 2:1 Video Switch
Features -50dB Off Isolation at 30MHz -80dB Non-Adjacent Channel Crosstalk at 30MHz 3dB Bandwidth: 800MHz On Resistance: 4 (Typical) Low Power Consumption: 1µA (Maximum) Control Input TTL Compatible Applications
More informationPI5A4684. Chip Scale Packaging, Dual SPDT Analog Switch. Features. Description. Pin Configuration/ Block Diagram (top view) CSP.
Features CMOS Technology for Bus and Analog Applications Low On-Resistance: 0.5Ω. Wide Range: 1.65V to 5.5V Rail-to-Rail Signal Range Control Input Overvoltage Tolerance: 5.5V min. High Off Isolation:
More informationFSA2269 / FSA2269TS Low-Voltage Dual-SPDT (0.4 ) Analog Switch with Negative Swing Audio Capability
July 2013 FSA2269 / FSA2269TS Low-Voltage Dual-SPDT (0.4 ) Analog Switch with Negative Swing Audio Capability Features 0.4 Ω Typical On Resistance (R ON) for +3.0 V Supply 0.25 Ω Maximum RON Flatness for
More informationFST Bit Bus Switch
Features 4 Ω Switch Connection between Two Ports Minimal Propagation Delay through the Switch Low I CC Zero Bounce in Flow-through Mode Control Inputs Compatible with TTL Level Description December 2012
More informationPI5A3167C Low Voltage SPST 0.8Ω Analog Switch
Features Description CMO Technology for us and nalog pplications Low On-Resistance: 0.8Ω at 3.0V Wide Range: 1.65V to 5.5V Rail-to-Rail ignal Range Control Input Overvoltage Tolerance: 5.5V Fast Transition
More informationFSAV430 Low Voltage 1.1GHz, 4-Channel, 2:1 Video Switch
FSAV430 Low Voltage 1.1GHz, 4-Channel, 2:1 Video Switch Features -40dB Off Isolation at 30MHz -60dB Non-Adjacent Channel Crosstalk at 30MHz 3dB Bandwidth: 1.1GHz On Resistance: 4.5 (Typical) Low Power
More informationPI5A23159 Low Voltage Dual SPDT 0.8Ω Analog Switch
Features CMOS Technology for Bus and Analog Applications Low On-Resistance: 0.8 at 3.0V Wide Range: 1.65V to 5.5V Rail-to-Rail Signal Range Control Overvoltage Tolerance: 5.5V(Min) Fast Transition Speed:
More informationSTG3693. Low voltage high bandwidth quad SPDT switch. Features. Description
Low voltage high bandwidth quad SPDT switch Datasheet - production data Features Ultra low power dissipation: I CC = 0.3 µa at T A = 125 C Low on-resistance: R DS(on) = 4 Ω (T A = 25 C) at V CC = 3.0 V
More informationWAS4729QB QB* WAS4729QB. Descriptions. Features. Applications. Order information
WAS4729QB Low On Resistance (0.75Ω) Dual SPDT Analog Switch with Negative Swing Audio Capability Http//:www.sh-willsemi.com Descriptions The WAS4729QB is a high performance, dual Single Pole Double Throw
More informationWAS4723Q WAS4723Q. Order information 1 2 VCC NO1. Low On Resistance, Dual SPDT Analog Switch. Http//: QFN L
WAS4723Q Low On Resistance, Dual SPDT Analog Switch Http//:www.willsemi.com Descriptions The WAS4723Q is a high performance, dual Single Pole Double Throw (SPDT) analog switch that features ultra-low Ron
More information74AUP1G95 TinyLogic Low Power Universal Configurable Two-Input Logic Gate (Open Drain Output)
74UPG9 TinyLogic Low Power Universal onfigurable Two-Input Logic Gate (Open Drain Output) Features 0.8 V to.6 V V Supply Operation.6 V Over-Voltage Tolerant I/Os at V from 0.8V to.6 V Extremely High Speed
More informationTOP VIEW COM2. Maxim Integrated Products 1
19-3472; Rev ; 1/4 Quad SPST Switches General Description The quad single-pole/single-throw (SPST) switch operates from a single +2V to +5.5V supply and can handle signals greater than the supply rail.
More informationFSUSB45 Hi-Speed USB2.0 (480Mbps) Switch with Dedicated Charger Port Detect
December 2009 FSUSB45 Hi-Speed USB2.0 (480Mbps) Switch with Dedicated Charger Port Detect Features Low On Capacitance: 7.0pF Typical Low On Resistance: 3.9Ω Typical Low Power Consumption: 1μA Maximum -
More informationNC7SB3157, FSA3157 Low-Voltage SPDT Analog Switch or 2:1 Multiplexer / De-multiplexer Bus Switch
NC7B3157, F3157 Low-oltage PDT nalog witch or 2:1Multiplexer / De-multiplexer Bus witch Features Useful in Both nalog and Digital pplications pace-aving, C7 6-Lead urface Mount Package Ultra-mall, MicroPak
More informationDG1411E, DG1412E, DG1413E. 1.5 On Resistance, ± 15 V / +12 V / ± 5 V, Quad SPST Switches. Vishay Siliconix.
1.5 On Resistance, ± 15 / +12 / ± 5, Quad SPST Switches DESCRIPTION The are ± 15 precision monolithic quad single-pole single-throw (SPST) CMOS analog switches. Built on a new CMOS process, the ishay Siliconix
More informationTOP VIEW COUT1 COM2. Maxim Integrated Products 1
19-77; Rev ; 7/4.75Ω, Dual SPDT Audio Switch with General Description The dual, single-pole/double-throw (SPDT) switch operates from a single +2V to +5.5V supply and features rail-to-rail signal handling.
More informationFT3001 Reset Timer with Configurable Delay
FT3001 Reset Timer with Configurable Delay Features Delay Times: 3.0, 3.75, 4.5, 6.0 Seconds 1 µa I CC Current Consumption in Standby Primary and Secondary Input Reset Pins Push-Pull and Open-Drain Output
More informationSTG5682. Low voltage dual SPDTswitch with negative rail capability. Features. Description
Low voltage dual SPDTswitch with negative rail capability Features Distortion-free negative signal throughput down to V CC -5.5V Wide operating voltage range: V CC (Opr) = 1.65V to 4.5V single supply Ultra
More informationFSA806 USB2.0 High-Speed (480Mbps), UART, and Audio Switch with Negative Signal Capability
July 2012 FSA806 USB2.0 High-Speed (480Mbps), UART, and Audio Switch with Negative Signal Capability Features 3:1 Switch Handles: - Audio Headsets - UART - Up to Two High- and Low-Speed USB Data Negative-Swing-Capable
More informationWAS4732D WAS4732D. Descriptions. Features. Order information. Applications. MIC/GND Cross-point Switch for EU/US Headphone Compatible Application
/ Cross-point Switch for EU/US Headphone Compatible Application http://www.sh-willsemi.com Descriptions The is a 2x2 cross-point switch that is used to interchange the Ground and connections on a headphone
More informationFSA3031 Dual High-Speed USB2.0 with Mobile High-Definition Link (MHL )
FSA3031 Dual High-Speed USB2.0 with Mobile High-Definition Link (MHL ) Features Low On Capacitance: 4.6 pf/6.75 pf MHL/USB (Typical) Low Power Consumption: 30 μa Maximum Supports MHL Rev. 2.0 Passes 1080
More information0.39, Low-R ON, Ultra-Low Distortion, Compact DPDT Analog Switch
.39, Low-R ON, Ultra-Low Distortion, Compact DPDT Analog Switch DESCRIPTION The is a compact, low resistance, ultra-low distortion double pole double throw (DPST) analog switch. The features a flat.39
More informationAS11P2TLR. Low voltage 1 Ω single-pole double-throw analog switch with breakbefore-make. Description. Features
Low voltage 1 Ω single-pole double-throw analog switch with breakbefore-make feature Description Datasheet - production data Features DFN6L High speed: t PD = 130 ps (typ.) at V CC = 3.0 V t PD = 140 ps
More informationUM Ω Ultra Low ON-Resistance Dual SPDT Analog Switch UM5223 QFN General Description. Applications
0.5Ω Ultra Low ON-Resistance Dual SPDT Analog Switch UM5223 QFN10 1.8 1.4 General Description The UM5223 is a low on-resistance (R ON ), dual single-pole/double-throw (SPDT) analog switch operates from
More informationNC7SZ125 TinyLogic UHS Buffer with Three-State Output
NC7SZ125 TinyLogic UHS Buffer with Three-State Output January 2014 NC7SZ125 TinyLogic UHS Buffer with Three-State Output Features Ultra-High Speed: t PD 2.6 ns (Typical) into 50 pf at 5 CC High Output
More informationNC7SZ74 TinyLogic UHS D-Type, Flip-Flop with Preset and Clear
NC7SZ74 TinyLogic UHS D-Type, Flip-Flop with Preset and Clear Features Ultra-High Speed: t PD 2.6 (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Power
More informationNC7WZ07 TinyLogic UHS Dual Buffer (Open-Drain Outputs)
April 2013 NC7WZ07 TinyLogic UHS Dual Buffer (Open-Drain Outputs) Features Ultra-High Speed: t PZL 2.3 ns (Typical) High I OL Output Drive: ±24 ma at 3 CC Broad CC Operating Range: 1.65 to 5.50 Power Down
More informationNC7WZ16 TinyLogic UHS Dual Buffer
NC7WZ16 TinyLogic UHS Dual Buffer Features Ultra-High Speed: t PD 2.4ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Matches Performance of LCX when
More informationWAS4899Q WAS4899Q. Descriptions. Features. Order information. Applications. Low On Resistance, Quad SPDT Analog Switch. Http//:
WAS4899Q Low On Resistance, Quad SPDT Analog Switch Http//:www.willsemi.com Descriptions The WAS4899Q is a high performance, quad, Single Pole Double Throw (SPDT) analog switch that features ultra-low
More informationFSUSB73 3:1 High-Speed USB Multiplexer and Hub Routing Switch
April 2012 FSUSB73 3:1 High-Speed USB Multiplexer and Hub Routing Switch Features Switch Type 3:1 MUX + Isolation Switch USB USB 2.0 High-Speed & Full-Speed Compliant R ON 6.5Ω C ON ESD (IEC61000-4-2)
More informationFeatures. Applications
PRELIMINARY DATASHEET IDTHS421V16 Description The IDTHS421V16 is a bi-directional, low power, Quad single-pole, double-throw (SPDT) hybrid switch targeted at dual SIM card multiplexing. It is optimized
More informationFSUSB46 Hi-Speed USB2.0 (480Mbps) DPST Switch with Dedicated Charger Port Detection
March 2013 FSUSB46 Hi-Speed USB2.0 (480Mbps) DPST Switch with Dedicated harger Port Detection Features Low On apacitance: 7.0pF Typical Low On Resistance: 3.9Ω Typical Low Power onsumption: 1μA Maximum
More informationFSUSB63 3:1 High-Speed USB 2.0 Switch / Multiplexer
July 2013 FSUSB63 3:1 High-Speed USB 2.0 Switch / Multiplexer Features Switch Type 3:1 USB Switch USB USB 2.0 High-Speed & Full-Speed Compliant Break-Before-Make Time 126µs R ON 6Ω Typical C ON 6pF Typical
More informationFEATURES BENEFITS APPLICATIONS. PARAMETER LIMIT UNIT Reference to GND V to +6 IN, COM, NC, NO a -0.3 to (V )
DESCRIPTION www.vishay.com.5, High Bandwidth, Dual SPDT Analog Switch The DGE is a low-voltage dual single-pole / double-throw monolithic CMOS analog switch. Designed to operate from. V to 5.5 V power
More informationFSA2268 / FSA2268T Low-Voltage Dual-SPDT (0.4 ) Analog Switch with 16kV ESD
FSA2268 / FSA2268T Low-Voltage Dual-SPDT (0.4 ) Analog Switch with 16kV ESD Features 0.4Ω Typical On Resistance (R ON) for +3.0V Supply 0.25Ω Maximum R ON Flatness for +3.0V Supply -3db Bandwidth: > 50MHz
More informationIs Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
More informationFST Bit Bus Switch
Features 4Ω Switch Connection between Two Ports Minimal Propagation Delay through the Switch Low I CC Zero Bounce in Flow-through Mode Control Inputs Compatible with TTL Level Description March 2008 Fairchild
More informationObsolete Product(s) - Obsolete Product(s) Obsolete Product(s) - Obsolete Product(s) STG3684
LOW VOLTAGE 0.5Ω MAX DUAL SPDT SWITCH WITH BREAK BEFORE MAKE FEATURE HIGH SPEED: t PD = 0.3ns (TYP.) at V CC = 3.0V t PD = 0.4ns (TYP.) at V CC = 2.3V ULTRA LOW POWER DISSIPATION: I CC = 0.2µA (MAX.) at
More information74AC14, 74ACT14 Hex Inverter with Schmitt Trigger Input
74AC14, 74ACT14 Hex Inverter with Schmitt Trigger Input Features I CC reduced by 50% Outputs source/sink 24mA 74ACT14 has TTL-compatible inputs Ordering Information Order Number General Description Package
More information0.4, Low Resistance and Capacitance, Dual DPDT / Quad SPDT Analog Switch
.4, Low Resistance and Capacitance, Dual DPDT / Quad SPDT Analog Switch DESCRIPTION The DG2523 and DG2524 are four-channel single-pole double-throw (SPDT) analog switches. The DG2523 has two control inputs
More informationMP2735/MP2736 Low-Voltage 0.45Ω Dual SPDT Analog Switches
The Future of Analog IC Technology GENERAL DESCRIPTION The MP2735/MP2736 are low voltage, low onresistance, dual single-pole, double-throw (SPDT) monolithic CMOS analog switches designed for high performance
More information700 MHz, -3 db Bandwidth; Single SPDT Analog Switch
7 MHz, -3 db Bandwidth; Single SPDT Analog Switch DESCRIPTION is a low R ON, high bandwidth analog switch configured in single SPDT. It achieves 5 switch on resistance, greater than 7 MHz -3 db bandwidth
More informationDG2706. High Speed, Low Voltage, 3, Quad SPDT CMOS Analog Switch. Vishay Siliconix DESCRIPTION FEATURES APPLICATIONS
High Speed, Low Voltage, 3, Quad SPDT CMOS Analog Switch DESCRIPTION The DG2706 is a high speed, low voltage, low On-resistance, quad SPDT (single pole double throw) analog switch. It operates from a.6
More informationAutomotive 125 C Analog Switch Dual DPDT / Quad SPDT, 0.37, 338 MHz Bandwidth
Automotive 125 C Analog Switch Dual DPDT / Quad SPDT, 0.37, 338 MHz Bandwidth DESCRIPTION The, is a four-channel single-pole double-throw (SPDT) analog switch with two control inputs. It is also known
More informationLow-Voltage, Low R ON, SPDT Audio Switch with Negative Swing Capability
Low-Voltage, Low R ON, SPDT Audio Switch with Negative Swing Capability DG6, DG63 DESCRIPTION The DG6, DG63 is a low on-resistance, single-pole/ double-throw monolithic CMOS analog switch with negative
More informationNC7SZ157 TinyLogic UHS 2-Input Non-Inverting Multiplexer
NC7SZ157 TinyLogic UHS 2-Input Non-Inverting Multiplexer Features Broad CC Operating Range: 1.65 to 5.5 Ultra High-Speed Power Down High-Impedance Inputs/Outputs Over-oltage Tolerance Inputs Facilitate
More informationSTG3693. Low voltage high bandwidth Quad SPDT switch. Features. Description
Low voltage high bandwidth Quad SPDT switch Features Ultra low power dissipation: I CC = 0.2μA (Max.) at T A = 85 C Low ON resistance: R ON = 4Ω (T A = 25 C) at V CC = 3.0V Wide operating voltage range:
More informationDEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO TITLE MICROCIRCUIT, DIGITAL-LINEAR, 1 OHM, SPDT ANALOG SWITCH, MONOLITHIC SILICON REVISIONS
REVISIONS LTR DESCRIPTION DTE PPROVED Update document paragraphs to current requirements. - ro 14-06-25 C. SFFLE CURRENT DESIGN CTIVITY CGE CODE HS CHNGED NMES TO: DL LND ND MRITIME 43218-3990 Prepared
More information0.45, Low Voltage Dual SPDT Analog Switch with Negative Swing Audio Capability
5, Low Voltage Dual SPDT Analog Switch with Negative Swing Audio Capability DESCRIPTION The is a dual SPDT low on-resistance switch designed to from a single 1.6 V to 5.5 V power supply. It is a bi-directional
More informationPrecision Monolithic Quad SPST CMOS Analog Switches
Precision Monolithic Quad SPST CMOS Analog Switches DESCRIPTION The are ± 15 precision monolithic quad single-pole single-throw (SPST) CMOS analog switches. Built on a new CMOS process, the ishay Siliconix
More informationSTG3699AQTR LOW VOLTAGE 0.5Ω MAX QUAD SPDT SWITCH WITH BREAK-BEFORE-MAKE FEATURE
LOW VOLTAGE 0.5Ω MAX QUAD SPDT SWITCH WITH BREAK-BEFORE-MAKE FEATURE HIGH SPEED: t PD = 1.5ns (TYP.) at V CC = 3.0V t PD = 1.5ns (TYP.) at V CC = 2.3V ULTRA LOW POWER DISSIPATION: I CC = 0.2µA (MAX.) at
More informationPI5A100. Precision, Wide-Bandwidth Quad SPDT Analog Switch. Description. Features. Block Diagram, Pin Configuration. Applications.
Precision, Wide-Bandwidth Quad SPDT Analog Switch Features Single Supply Operation (+2V to +6V) Rail-to-Rail Analog Signal Dynamic Range Low On-Resistance (6Ω typ with 5V supply) Minimizes Distortion and
More informationMM74HC86 Quad 2-Input Exclusive OR Gate
MM74HC86 Quad 2-Input Exclusive OR Gate Features Typical Propagation Delay: 9ns Wide Operating oltage Range: 2 6 Low Input Current: 1mA Maximum Low Quiescent Current: 20mA Max. (74 Series) Output Drive
More informationFSA3200 Two-Port, High-Speed USB2.0 Switch with Mobile High-Definition Link (MHL )
November 2012 FSA3200 Two-Port, High-Speed USB2.0 Switch with Mobile High-Definition Link (MHL ) Features Low On Capacitance: 2.7 pf / 3.1 pf MHL / USB (Typical) Low Power Consumption: 30μA Maximum Supports
More informationPrecision Quad SPDT Analog Switch
Precision Quad SPDT Analog Switch DESCRIPTION The consist of four independently controlled single-pole double-throw analog switches. These monolithic switch is designed to control analog signals with a
More informationNC7SZ14 TinyLogic UHS Inverter with Schmitt Trigger Input
January 2010 NC7SZ14 TinyLogic UHS Inverter with Schmitt Trigger Input Features Ultra-High Speed: t PD 3.7ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65
More informationNC7SZ38 TinyLogic UHS 2-Input NAND Gate, Open Drain Output
NC7SZ38 TinyLogic UHS 2-Input NAND Gate, Open Drain Output Features Ultra-High Speed: t PD 2.4ns (Typical) into 50pF at 5V V CC Open Drain Output Stage for OR Tied Applications High Output Sink Drive:
More informationIs Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
More informationNC7SZ00 TinyLogic UHS Two-Input NAND Gate
NC7SZ00 TinyLogic UHS Two-Input NAND Gate Features Ultra-High Speed: t PD 2.4ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Matches Performance of
More informationNC7SV57 / NC7SV58 TinyLogic ULP-A Universal Configurable Two-Input Logic Gates
December 2010 NC7S57 / NC7S58 TinyLogic ULP-A Universal Configurable Two-Input Logic Gates Features 0.9 to 3.6 CC Supply Operation 3.6 Over-oltage Tolerant I/Os at CC from 0.9 to 3.6 Extremely High Speed
More informationNC7SZ08 TinyLogic UHS Two-Input AND Gate
NC7SZ08 TinyLogic UHS Two-Input AND Gate Features Ultra-High Speed: t PD 2.7ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Matches Performance of
More informationNC7SZ86 TinyLogic UHS Two-Input Exclusive-OR Gate
NC7SZ86 TinyLogic UHS Two-Input Exclusive-OR Gate Features Ultra-High Speed: t PD 2.9ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Matches Performance
More informationNC7SV05 TinyLogic ULP-A Inverter (Open-Drain Output)
NC7SV05 TinyLogic ULP-A Inverter (Open-Drain Output) Features 0.9V to 3.6V V CC Supply Operation 3.6V Over-Voltage Tolerant I/Os at VCC from 0.9V to 3.6V Extremely High Speed tpd - 1.0ns: Typical for 2.7V
More informationSGM Ω, High Speed, Low Voltage Dual, DPDT Analog Switch
GENERAL DESCRIPTION The SGM44601 is a high-speed, low-voltage, advanced dual-independent double-pole/double-throw (DPDT) CMOS analog switch that is designed to operate from a single +1.8V to +5.5V power
More informationPrecision Monolithic Quad SPST CMOS Analog Switches
Precision Monolithic Quad SPST CMOS Analog Switches DESCRIPTION The DG4 series of monolithic quad analog switches was designed to provide high speed, low error switching of precision analog signals. Combining
More informationFSAL200 Wide Bandwidth Quad 2:1 Analog Multiplexer / De-multiplexer Switch
FSAL200 Wide Bandwidth Quad 2:1 Analog Multiplexer / De-multiplexer Switch Features Typical 6Ω Switch Connection Between Two Ports Minimal Propagation Delay Through the Switch Low I CC Zero Bounce in Flow-Through
More informationSub-Ω, Low Voltage, SPDT Analog Switches with Over Current Protection
New Product DG/DG1 Sub-Ω, Low Voltage, SPDT Analog Switches with Over Current Protection DESCRIPTION The DG/DG1 are low-voltage single single-pole/ double-throw monolithic CMOS analog switches. Designed
More informationFSHDMI04 Wide-Bandwidth Differential Signaling HDMI Switch
Click to see this datasheet in Simplified Chinese! Wide-Bandwidth Differential Signaling HDMI Switch Features 1.65 Gbps throughput 8kV ESD protection -26dB non-adjacent channel crosstalk at 825MHz Isolation
More informationNC7SZU04 TinyLogic UHS Unbuffered Inverter
NC7SZU04 TinyLogic UHS Unbuffered Inverter Features Unbuffered for Crystal Oscillator and Analog Applications Balanced Output Drive: ±16mA at 4.5 CC Broad CC Operating Range: 1.65 to 5.5 Matches Performance
More informationSTG3699B. Low voltage 0.5 Ω max, quad SPDT switch with break-before-make feature. Features. Description
Low voltage 0.5 Ω max, quad SPDT switch with break-before-make feature Features High speed: t PD = 1.5 ns (typ.) at V CC = 3.0 V t PD = 1.5 ns (typ.) at V CC = 2.3 V Ultra low power dissipation: I CC =0.2μA
More informationDual SPDT Analog Switch
Dual SPDT Analog Switch DESCRIPTION The DG9236 is a CMOS, dual SPDT analog switch designed to operate from = 2.7 V to = 6 V max. operating, single supply. All control logic inputs have a guaranteed.8 V
More informationSTG3220. Low voltage high bandwidth dual SPDT switch. Features. Description. Applications
Low voltage high bandwidth dual SPDT switch Features Ultra low power dissipation: I CC = 1 μa (max.) at T A = 85 C Low "ON" resistance: R ON = 4.8 Ω (T A = 25 ºC) at V CC = 4.3 V R ON = 5.9 Ω (T A = 25
More informationFSSD07 1-Bit / 4-Bit SD/SDIO and MMC Dual-Host Multiplexer
March 2012 FSSD07 1-Bit / 4-Bit SD/SDIO and MMC Dual-Host Multiplexer Features On Resistance: 5Ω Typical, V DDC =2.7V f toggle : >75MHz Low On Capacitance: 6pF Typical Low Power Consumption: 2µA Maximum
More informationNC7SZ125 TinyLogic UHS Buffer with Three-State Output
NC7SZ125 TinyLogic UHS Buffer with Three-State Output Features Ultra-High Speed: t PD 2.6ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Matches Performance
More informationFAN5701 Compact 6-LED Driver for Mobile Platforms
March 2013 FAN5701 Compact 6-LED Driver for Mobile Platforms Features Six (6) Parallel LEDs (up to 30mA each) Total Package Load Current Capability: 180mA Two Default Groups of Four (4) and Two (2) LEDs
More informationSGM Ω, 300MHz, Low-Power Full-Speed USB (12Mbps) Switch
GENERAL ESCRIPTION The SGM2258 is a high-performance, dual, single-pole/ double-throw (SPT) CMOS analog switch designed for switching USB 1.1 signals. High bandwidth and low on-resistance make this switch
More informationFSA2457 Dual DPDT, 5Ω Analog Data Switch
FSA2457 Dual DPDT, 5Ω Analog Data Switch Features Low On Capacitance for Data Path: 12pF Typical Low On Resistance for Data Path: 5Ω Typical Low Pow er Quiescent Consumption: 1μA Maximum Wide -3db Bandw
More informationIs Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
More informationSTMUX3040. NEATSwitch : octal SPDT high bandwidth signal switch. Features. Description. Applications
NEATSwitch : octal SPDT high bandwidth signal switch Features Supports 3.0 Gbps generic data rate Octal SPDT switch to support 2 PCI lanes Low R ON : 5.5 Ω typical Internal voltage regulator V CC operating
More informationIs Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
More information