B11.14 LINK ARMS AND HINGES B11 TILT-TURN WINDOWS
|
|
- Clinton Malone
- 5 years ago
- Views:
Transcription
1 B11 TILT-TURN WINDOWS B11.14 LINK ARMS AND HINGES Waregemstraat Zulte - Belgium - T F commercial@sobinco.com -
2 CONTENTS 1. General...B Size range...b Chrono visible hinges...b Hinges B Preparations B Chrono Invision Pro hinges...b Hinge set f frame groove 14/18 mm B Hinge set f frame groove 10/14 mm B Installation of hinges B Adjustments of hinges B Chrono Invision Go hinges...b Hinge set f frame groove 14/18 mm B Hinge set f frame groove 10/14 mm B Installation of hinges B Adjustment of hinges B B
3 1. General B11.14 The totally clampable Chrono tilt and turn system is available with visible hinges and with concealed hinges. The concealed hinges offer the following advantages: The concealed hinges have the advantage that the hinges are invisible when the window is closed. The possibility to use a narrow frame profile: aesthetic aspect and glass surface will be larger. The cleaning of the window frames will be easier because all the cners are easily accessible. Colour-independent, so reducing stock and increasing cost effectiveness. No need to remove the inner gasket to mount the hinges. A better acoustic, wind and water tightness is obtained. The fully concealed hinges can not be damaged spoilt during transpt, installation other wk to the building. The concealed hinges are available in two different versions: Chrono Invision Pro: fully concealed clampable hinges, which can carry vent weights up to 170 kg. Chrono Invision Go: fully concealed clampable hinges, which can carry vent weights up to 90 kg. Link arms: F good stability and operation of the window there are, dependent of the vent width, 2 3 sizes of link arms. The two biggest link arms are provided with a pre-locking pull-in wedge to ease closing from the tilt position. The link arm is provided with an anti slam shut device (click system) to avoid unintended closing of the window in the tilt position. F assembly purposes the link arm is kept in the turn position by a snap-off pin until the first operation. A special self-drilling screw ensures solid and dimensionally accurate fixing of the link arm. All parts are made of non-croding materials. Profile dimensions Chrono hardware is available to suit a frame groove of 14/18 mm a frame groove of 10/14 mm. Chrono Invision Pro Chrono Invision Go Frame groove 14/18 mm Frame groove 10/14 mm A 14 ± ± 0.5 B 18 ± ± 0.5 Cut out vent profile B
4 2. Size range Chrono Size range with connection piece set: Vent width: mm. Vent height: mm. Size range f vent heights > 2400 mm: Vent width: mm. Vent height: mm. Vent weight: max. 130 kg. Ratio of vent width Fb / vent height Fh = max. 1,5. Size range with lockcase: Vent width: mm. Vent height: mm. Chrono Invision Pro Size range with connection piece set: Vent width: mm. Vent height: mm. Size range f vent heights > 2400 mm: Vent width: mm. Vent height: mm. Vent weight: max. 170 kg. Ratio of vent width Fb / vent height Fh = max. 1,5 (< 130 kg). Ratio of vent width Fb / vent height Fh = max. 1 (> 130 kg). Fb < 670 mm: max. 130 kg. Fb > 670 mm: max. 170 kg. Size range with lockcase: Vent width: mm. Vent height: mm. Chrono Invision Go Size range with connection piece set: Vent width: mm. Vent height: mm. Size range f vent heights > 2400 mm: Vent width: mm. Vent height: mm. Vent weight: max. 90 kg. Ratio of vent width Fb / vent height Fh = max. 1,2. Size range with lockcase: Vent width: mm. Vent height: mm. Remarks Dimensions out of standard range on request! B
5 3. Chrono visible hinges 3.1. Hinges By default the hinges can carry vent weights up to 90 kg. F weight > 90 kg and/ a vent width > 1400 mm the reinfcement set n must be placed. When dering please indicate the following: link arm n , (dependent of the width) set non-colour fixed hinge parts n set colour fixed hinge parts n reinfcement set n (vent weight > 90 kg and/ Fb > 1400 mm) Link arm n , Set non-colour fixed hinge parts n screw top hinge hinge pin bottom hinge hinge pin top hinge adjustment bearing piece bottom hinge screw bottom hinge clamping plate bottom hinge >90kg and/ Fb>1400mm Set colour fixed hinge parts n vent part top hinge vent part bottom hinge frame part top hinge frame part bottom hinge cap bottom hinge Reinfcement set n (>90kg and/ Fb>1400 mm) reinfcement set screw Plate n f suppting adjusting screw (der separately) B
6 Remarks The adjustable hinges have been tested in accdance with the standards of windows. Therefe the hinges can not be used f balcony dos with a do function. F windows with vent weights from 130 kg to 170 kg we recommend Chrono Invision Pro hinges Preparations Seals top and bottom hinge top hinge bottom hinge Reinfcement set F windows with vent weight > 90 kg and when Fb > 1400 mm the reinfcement set n must be used to reinfce the adjustable top hinge. The M4x10 thread fming screws must fix into at least 6 mm of aluminium. Drilling jig n is available f drilling the holes. Maintenance Lubricate the adjustment bearing piece of the bottom hinge. You will find me infmation in the maintenance instructions. B
7 4. Chrono Invision Pro hinges 4.1. Hinge set f frame groove 14/18 mm F a good stability and operation of the window there are f Chrono Invision Pro three different hinge sets. F weights > 130 kg the reinfcement set n should be placed. Right hand = illustrated Left hand = opposite view Hinge set n R(L) Fb = mm Hinge set n R(L) Fb = mm Hinge set n R(L) Fb = mm >130kg and/ Fb>1400mm Hinge set n R(L) R(L) link arm R(L) bottom hinge Hinge set n R(L) R(L) link arm R(L) bottom hinge Hinge set n R(L) R(L) link arm R(L) bottom hinge Reinfcement set n (>130 kg and/ Fb>1400 mm) reinfcement piece 1 St4.2x13Din7504P drilling screw >130kg and/ Fb>1400mm B
8 4.2. Hinge set f frame groove 10/14 mm F a good stability and operation of the window there are three different hinge sets f Chrono Invision Pro. F weights > 130 kg the reinfcement set n should be placed. Right hand = illustrated Left hand = opposite view >130kg and/ Fb>1400mm Hinge set n R(L) Fb = mm Hinge set n R(L) Fb = mm Hinge set n R(L) Fb = mm Hinge set n R(L) R(L) link arm R(L) bottom hinge Hinge set n R(L) R(L) link arm R(L) bottom hinge Hinge set n R(L) R(L) link arm R(L) bottom hinge Reinfcement set n (>130kg and/ Fb>1400 mm) reinfcement piece stop >130kg and/ Fb>1400mm B
9 4.3. Installation of hinges Fixing vent part of bottom hinge Fb > 1400 mm and/ Fg > 130 kg Fixing vent part of bottom hinge right left INSIDE INSIDE Installation of link arm and cner transmission on the vent Positioning and fixing link arm on the vent Remove retaining piece Remove positioning clips after assembly Fixing frame part of the bottom hinge on the frame profile Assembly of vent and frame Press right into cner B
10 Installation link arm (vent) on frame profile Fixing link arm Frame groove 14/18 mm Fixing of the drilling screw (reinfcement set 170 kg) Fixing of the stop (reinfcement set 170 kg) Frame groove 10/14 mm Installation of the reinfcement plate Press right into cner Fg > 130 kg and frame groove 14/18 mm Fg > 130 kg and frame groove 10/14 mm Vent weight > 130 kg Fixing of the link arm on the frame profile Press right into cner Turn position to tilt position B
11 4.4. Adjustments of hinges Overview adjustments Bottom hinge Continuous hizontal and vertical adjustment range of ±1.5 mm. Adjustable without releasing fixing screws and without removing the vent. Adjustable friction device f turn mode. Link arm Continuous hizontal adjustment range of +2 mm/-4 mm. Gasket pressure adjustment of ±0.8 mm. Opening angle The maximum opening angle is adjustable on the bottom hinge ( ). Adjustment link arm Adjustment vent part of bottom hinge B
12 Adjustment frame part of the bottom hinge Adjustment of the friction mechanism Adjustment of the opening angle (90 to 105 ) befe mounting the hinge B
13 5. Chrono Invision Go hinges 5.1. Hinge set f frame groove 14/18 mm F a good stability and operation of the window there are two different hinge sets f Chrono Invision Go. Vent weight = max. 90 kg. Right hand = illustrated Left hand = opposite view Hinge set n R(L) Fb = mm Hinge set n R(L) Fb = mm Hinge set n R(L) R(L) link arm R(L) vent part bottom hinge R(L) frame part bottom hinge guiding piece bottom hinge Hinge set n R(L) R(L) link arm R(L) vent part bottom hinge R(L) frame part bottom hinge guiding piece bottom hinge B
14 5.2. Hinge set f frame groove 10/14 mm F a good stability and operation of the window there are two different hinge sets f Chrono Invision Go. Vent weight = max. 90 kg. Right hand = illustrated Left hand = opposite view Hinge set n R(L) Fb = mm Hinge set n R(L) Fb = mm Hinge set n R(L) R(L) link arm R(L) vent part bottom hinge R(L) frame part bottom hinge guiding piece bottom hinge Hinge set n R(L) R(L) link arm R(L) vent part bottom hinge R(L) frame part bottom hinge guiding piece bottom hinge B
15 5.3. Installation of hinges Installation vent part of bottom hinge Fixing vent part of bottom hinge Right hand window Left hand window INSIDE Hook in the arm in the guiding piece and fully open the hinge to click in. Installation of link arm and cner transmission on the vent OR Slide back the link arm up against the snap-off pin of the cner transmission positioning piece. Positioning piece (when no cner transmission) Fixing link arm on the vent PUSH! B
16 Hook in frame part of the bottom hinge on the vertical frame profile Slide downwards the frame part of the bottom hinge Fix the frame part of the bottom hinge on the frame profile PUSH! PUSH! Assembly of vent and frame Position clamping nut! Installation link arm (vent) on frame profile Open frame part at 90 and hook in vertically behind the groove tooth (13a). Then insert in the top frame profile (13b). Fixing frame part of the link arm Position clamping nut! PUSH! B
17 5.4. Adjustment of hinges Overview adjustments Bottom hinge Continuous hizontal and vertical adjustment range of ±1.5 mm. Adjustable without releasing fixing screws and without removing the vent. Link arm Continuous hizontal adjustment range of +2 mm/-4 mm. Gasket pressure adjustment of ±0.8 mm. Adjustment link arm Height adjustment vent part of the bottom hinge Hizontal adjustment frame part of the bottom hinge B
18
C13.11 HANDLES AND CONNECTION PIECES C13 SIDE HUNG WINDOWS
C13 SIDE HUNG WINDOWS C13.11 HANDLES AND CONNECTION PIECES 01.05.2014 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS
More informationC11.16 CHRONO ACCESSORIES C11 SIDE HUNG WINDOWS
C11 SIDE HUNG WINDOWS CHRONO ACCESSORIES 01.12.2018 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. Window stays....03
More informationsalto safe 4028 A12 Turn-tilt windows
A12 Turn-tilt windows salto safe 4028 01.09.2013 Waregemstraat 5-9870 Zulte - Belgium - T. 32 9 388 88 81 - F. 32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com salto safe 4028 Contents 1. General
More informationK15.13 FACE FIXED DOOR HINGES K15 DOORS
K15 DOORS K15.13 01.02.2017 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. General... K15.13.03 2. 2-part hinge...
More informationE11.15 HANDLES AND LOCKCASES E11 BOTTOM HUNG OPEN IN WINDOWS
E11 BOTTOM HUNG OPEN IN WINDOWS HANDLES AND LOCKCASES 01.12.2018 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. Handles
More informationK15.12 ROLLENBAND K15 DOORS
K15 DOORS 01.04.2015 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. General characteristics....03 2. Application range....03
More informationC11.15 HANDLES AND LOCKCASES C11 SIDE HUNG WINDOWS
C11 SIDE HUNG WINDOWS C11.15 HANDLES AND LOCKCASES 01.03.2018 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. Handles
More informationK11.11 ORCA K11 DOORS
K11 DOORS K11.11 01.06.2018 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. General...K11.11.03 1.1. Description and
More informationA11.15 HANDLES AND LOCKCASES A11 TURN-TILT WINDOWS
A11 TURN-TILT WINDOWS A11.15 HANDLES AND LOCKCASES 01.03.2018 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. Handles
More informationL11.12 B-SLIDE L11 SLIDING DOORS
L11 SLIDING DOORS L11.12 01.05.2014 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com L11.12 INDELING 1. General characteristics...l11.12.03
More informationK12.12 SINGLE LOCKS SERIES 8600 K12 DOORS
K12 DOORS K12.12 01.02.2017 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. Door locks series 8600... K12.12.03 1.1.
More informationK11.13 THREE-POINT LOCKS SERIES 8400 K11 DOORS
K11 DOORS K11.13 THREE-POINT LOCKS SERIES 8400 01.04.2017 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. Three-point
More informationMULTI MAMMUT Heavy-duty hardware
TECHNOLOGY IN MOTION www.maco.eu ASSEMBLY INSTRUCTIONS MULTI MAMMUT Heavy-duty hardware Only for use by certified specialists! Not for end users! TILT AND TURNHARDWARE Key/abbreviations Sash rebate height
More informationEDGE2 DUAL MONITOR ARM
EDGE2 DUAL MONITOR ARM EDGE2 Rev A 2/17 Model EDGE2-SLV Model EDGE2-BLK Model EDGE2-WHT ASSEMBLY AND ADJUSTMENT EDGE2 DUAL MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning
More informationK13.11 ORCA PANIC EXIT DEVICE K13 DOORS
K13 DOORS K13.11 01.06.2018 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. General information... K13.11.03 1.1. Standards
More informationHahn KT-R. Butt hinge for plastic doors
Hahn KT-R Butt hinge for plastic doors For explanations of the table, please visit www.dr-hahn.com Service classes Durability Weight of test door Fire resistance Security Corrosion resistance Intrusion
More informationVersion 2016_1.1 VICTORIAN ASSEMBLY INSTRUCTIONS. Victorian Vi-23, 34, 36
Version 2016_1.1 VICTORIAN ASSEMBLY INSTRUCTIONS Victorian Vi-23, 34, 36 PRODUCT INFORMATION Dear customer, Thank you for buying a high-quality aluminium greenhouse. REMARKS The drawings in these instructions
More informationmila-wall (Series100) General Operating Instructions page 1 of 15
mila-wall (Series100) General Operating Instructions page 1 of 15 Step #1: Before setting up walls, lower adjustable leveling feet on each panel approximately 1". This will allow access to the threaded
More informationOrganisational Kitchen Fittings Kitchen Cabinet Accessories
Kitchen waste bin systems Single waste bin, capacity 1 litres Carcase width: Min. 400 mm For door mounting: For left and right hand use Installation: Screw fixing to side panel Housing: Steel, plastic
More informationInstruction Manual. Manual Furniture Mover. Note: Owner/Operator must read and understand this instruction manual before using the furniture mover.
Instruction Manual Manual Furniture Mover Note: Owner/Operator must read and understand this instruction manual before using the furniture mover. I - Contents 1. Application 2 Specifications 3.Assembly
More informationFURNITURE HARDWARE & ACCESSORIES - PART 2 : SHELF SUPPORT AND SHELVING SYSTEMS
www.hafeleindia.com FURNITURE HARDWARE & ACCESSORIES - PART 2 : SHELF SUPPORT AND SHELVING SYSTEMS ABOUT ITALIANA FERRAMENTA ITALIANA FERRAMENTA is specialized in the production of high quality accessories
More informationBAKA Protect Serie 2000 / Protect. BAKA Protect Series 2000 / The adjustable hinge system for timber entrance doors
Protect Serie 2000 / 4000 Protect BAKA Protect Series 2000 / 4000 The adjustable hinge system for timber entrance doors index BAKA Protect 2D BAKA Protect 2010 2D two-dimensionally adjustable up to 120
More informationTREND-SETTING HARDWARE TECHNOLOGY. Roto NT. FB 28-1 GB October 2005 BKPM / Mammel (Translation: Prunty)
TREND-SETTING HARDWARE TECHNOLOGY 1 HINGE-SIDES FOR PVC WINDOWS Hinge-side K Hinge-side A Hinge-side V Hinge-side R 2 HINGE-SIDES FOR TIMBER WINDOWS Hinge-side E5 Hinge-side A Hinge-side V Hinge-side R
More informationFURNITURE HARDWARE & ACCESSORIES - PART 3 : LEVELLERS AND HANGERS
www.hafeleindia.com FURNITURE HARDWARE & ACCESSORIES - PART 3 : LEVELLERS AND HANGERS ABOUT ITALIANA FERRAMENTA ITALIANA FERRAMENTA is specialized in the production of high quality accessories and ironmongery
More informationDICTATOR RTS Tube Door Closer
Tube Door Closer RTS v long DICTATOR RTS Tube Door Closer The "Invisible" Door Closer The DICTATOR RTS tube door closer is built into the door and therefore is as good as invisible. The joint can only
More informationTECTUS. The completely concealed hinge system
TECTUS The completely concealed hinge system It s still design even if there s nothing to be seen! TECTUS This Latin word for concealed signifies SIMONSWERK s newly developed, completely hidden hinge system.
More informationDublin Stalls Installation Instructions
Dublin Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 9/13/17 Part Identification Round Track Bracket (4) (Not Painted) Round
More informationPrivacy Wall & Glass Selections Pivot-Hinged Door (For products manufactured after September 14, 2009)
Privacy Wall & Glass Selections Pivot-Hinged Door (For products manufactured after September 14, 2009) 3/16" HEX BIT #2 ACR BIT 3/8" HEX SOCKET Full-Height (No Switch) Transom (No Switch) Full-Height (With
More informationWeatherfold 4s 50, 75 & 100
Codes Weatherfold 4s 50, 75 & 100 Brio Australia P: +61 2 87186718 W: brio.com.au E: sales@brio.com.au Brio RMD UK Ltd. P: +44 191 2291224 W: briouk.com E: sales@briouk.com INSTBWS1 REV D - NOV 2011 Brio
More informationHinge Mortising Jig. One of the make it or break it parts of building a. 6 ShopNotes No. 74
Hinge Mortising Jig A Mortise for a Hinge. Quick, clean, and accurate that s the only way to describe the mortise you get with a trim router and this hinge mortising jig. One of the make it or break it
More informationAdjusting, Changing and Maintaining The Latches and Catches on Your Airstream
Adjusting, Changing and Maintaining The Latches and Catches on Your Airstream Hinges,Latches and Catches in your Airstream Bumps, pulling, gravity and time can have an affect on hinges and latches. Adjustments
More informationIPA BESLAG FOR SCHÜCO ALU INSIDE NORDIC A/S J. PETERSENS BESLAGFABRIK JACOB PETERSENSVEJ 9, DK-9240 NIBE TEL: (+45)
IPA BESLAG FOR SCHÜCO ALU INSIDE NORDIC 2015 A/S J. PETERSENS BESLAGFABRIK JACOB PETERSENSVEJ 9, DK-9240 NIBE TEL: (+45) 98 35 15 00 3 FITTINGS FOR SCHÜCO ALU INSIDE NORDIC Table of contents PAGE SCHÜCO
More informationInstallation Guide. Evolve bi-fold. 8. Door restrictor- optional p9. 1. Before you start p2. 9. Adjustment. 2. Measuring and surveying p2
Evolve bi-fold Installation Guide 1. Before you start p2 8. Door restrictor- optional p9 2. Measuring and surveying p2 3. Configuration details p4 4. Installation p5 5. Glazing p5 6. Glazing packer details
More informationASSEMBLY AND ADJUSTMENT
EDGE MONITOR ARM EDGE Rev A 2/17 Model EDGE-SLV Model EDGE-BLK Model EDGE-WHT ASSEMBLY AND ADJUSTMENT EDGE MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and
More informationFOLDING HARDWARE STARTEC T-SNAP G2/G4
FOLDING HARDWARE STARTEC T-SNAP G2/G4 T-SNAP G2 T-SNAP G4 Technical data: 40 kg for package throughout Height according 36+7 mm Fix bracket every 400 mm T-SNAP G2: 1x door leaf package T-SNAP G4: 2x door
More informationTECHNOLOGY IN MOTION MACO TILT AND TURN FITTINGS. MULTI POWER fully concealed fittings INSTALLATION INSTRUCTIONS
TECHNOLOGY IN MOTION MACO multi-matic TILT AND TURN FITTINGS INSTALLATION INSTRUCTIONS Key Sash rebate height Sash rebate width Tilt-only window 50 kg Maximum sash weight 2 Contents Applications/processing
More informationSection 1 Cubicles. Section 2 IPS Duct Panel Systems. Section 3 - Vanity Units Components & Assembly 12. Section 4 Basic Maintenance.
Contents Section 1 Cubicles Cubicle Components 3 Cubicle Installation 4-5 Cubicle Fittings Brackets 6 Hinges 7 Partition Support Leg 8 Indicator Bolt 9 Section 2 IPS Duct Panel Systems Frame, Flash & Panel
More informationDoor Hinges Drill-in Hinges
Drill-in hinge StarTec Frame part For timber lining frames For rebated doors Maintenance-free friction bearing To use in combination with receiver Max. door weight: 40 kg Knuckle: Ø15 mm Drilling bit Ø7.2
More information40mm Thermoclick. Type II Class 1 Clear Satin Anodize - 201R1 (Mid Grade Commercial)
http://www.sundancesupply.com 40mm Thermoclick Type II Class 1 Clear Satin Anodize - 201R1 (Mid Grade Commercial) U-Profile 12' Lengths $39 Out System offers a complete set of extrusions and accessories
More informationXL JOINERY LTD LA PORTE VISTA MODULAR 3 ASSEMBLY INSTRUCTIONS
XL JOINERY LTD LA PORTE VISTA MODULAR 3 2090mm High x 4687mm Wide ASSEMBLY INSTRUCTIONS READ AND UNDERSTAND THESE INSTRUCTIONS FULLY PRIOR TO STARTING INSTALLATION. IT IS STRONGLY RECOMMENDED THAT A COMPETENT
More informationRota-Bearing Rose & Doorknob Fitting Instructions
Rota-Bearing Rose & Doorknob Fitting Instructions The hole pattern will need to be created prior to fitting the doorknobs. Creating the Hole Pattern 38mm The fitting jig will allow for the accurate creation
More informationPow-R-Feed Systems Service Manual
Pow-R-Feed Systems Service Manual Important Safety Instructions Please read this manual carefully and follow its instructions. Improper use or failure to follow these instructions could result in serious
More informationSPIDA SAW OPERATIONS MANUAL
SPIDA SAW OPERATIONS MANUAL CM SERIAL NUMBER. OCTOBER 2000 CONTENTS Page description 1.) Contents 2.) Safety First 3.) CM Overview 4.) CM Specifications 5.) CM Installation 6.) CM Operation Setting the
More informationIPA FITTINGS FOR SCHÜCO ALU INSIDE NORDIC A/S J. PETERSENS BESLAGFABRIK JACOB PETERSENSVEJ 9, DK-9240 NIBE TEL: (+45)
IPA FITTINGS FOR SCHÜCO ALU INSIDE NORDIC 2017 A/S J. PETERSENS BESLAGFABRIK JACOB PETERSENSVEJ 9, DK-9240 NIBE TEL: (+45) 98 35 15 00 3 FITTINGS FOR SCHÜCO ALU INSIDE NORDIC Table of contents PAGE SCHÜCO
More informationINSTALLATION INSTRUCTIONS FOR PLASCORE NARROW STILE DOORS
INSTALLATION INSTRUCTIONS FOR PLASCORE NARROW STILE DOORS The following information is provided by Plascore, Inc., as a general guideline for the installation of the Plascore Narrow Stile Door and Jamb
More informationaluminium profile system
aluminium profile system 63 AME System aluminium profiles overview series profiles introduction 80x80 x80 x80/180 x Aluminium profiles are provided with longitudinal grooves which can be used in conjunction
More informationVersatrac Bypass Door Units, Conventional and Top Track, 300 and 400 Series
Versatrac Bypass Door Units, Conventional and Top Track, 300 and 400 Series TM Rough opening width (finished opening width plus 9/16") Notch for top track units (used as frame header) Rough opening height
More informationALU 4200-K/ZV Clampable tilt-sash fitting for aluminium windows
Clampable tilt-sash fitting for aluminium windows Further details and specifications/information regarding the product and liability (guidelines: VHBH, TBDK and VHBE) can be found in the aluminium planning
More informationINSTALLING YOUR NEW SPRING LIFT ARM KIT
INSTALLING YOUR NEW SPRING LIFT ARM KIT 1. Measure the distance that the roof is to be raised. [If your lift system is completely non-functional, you will need to calculate or estimate this distance as
More informationWooden Frame Type Instruction Manual
Wooden Frame TypeInstruction Manual Thank you for selecting our product. Before starting installation, please read this manual thoroughly to ensure correct installation. Please keep this manual at hand
More information* * 98/9950WDC. Fire-Rated Devices include these. additional components. 1-Point Latch (LBL)
*24739468* 24739468 98/9950WDC Installation Instructions 1-Point Latch (LBL) Fire-Rated Devices include these additional components Metal Edge Wrap required for 60 and 90-minute applications 2-Point Latch
More informationInstallation Manual for Metal Toilet Partitions Elite & Elite Plus Series
P a g e 1 Table of Contents Page General Notes and Tools Required 3 STEP 1: Establish Floor Bracket Locations 4 STEP 2: Fasten Floor Brackets 4 & 5 STEP 3: Erect Panels 6 STEP 4: Erect Wall Pilaster 7
More informationFig. 2 DORMA-Glas Stand/Issue 02/03 Seite/Page 1/7
FSW Installation instructions Track rail 75 x 72 mm 1. Ceiling substructure and installation of the track rail (Fig. 1): The track rail must be bolted over its entire length (including the stacking track
More informationCAM SYSTEM. Eccentric self-locking clamping devices. Set. CAM SYSTEM t. CAM SYSTEM t. Set. CAM SYSTEM s pag CAM SYSTEM s pag.
Eccentric self-locking CAM SYSEM Set CAM SYSEM t pag. 12 CAM SYSEM t pag. 126 Set CAM SYSEM s pag. 127 CAM SYSEM s pag. 128 EDGE CLAMP pag. 130 123 CAM-SYSEM eccentric self-locking he CAM SYSEM has been
More informationNEW. Perfect Fit Roller Blind System Measuring, assembly & fitting instructions
NEW Perfect Fit Roller Blind System Measuring, assembly & fitting instructions Perfect Fit Roller Blind System Measuring, assembly & fitting instructions Clearance & seals Seal Check clearance around the
More informationPATENTED NO WELD SYSTEM!
PATENTED NO WELD SYSTEM! Patented no weld aluminium batten system Various batten sizes snap onto simple fixing clip Fit to face of walls and ceilings or between pillars or posts Cut to size system with
More informationMODEL 200/220 ASSEMBLY INSTRUCTIONS
V-Twin MFG. Coats Tire Changer VT Part No. 16-0510 This tool should only be used by a knowledgeable and trained motorcycle technician V-Twin Mfg. accepts no responsibility for improper use. MODEL 200/220
More informationGIRTS ON BACK OF BUILDING
GIRTS ON BACK OF BUILDING ALL GIRTS ARE 1 1/2 SQUARE TUBE. GIRT LENGTHS FOR 12, 20, 24, AND 30 WIDE BUILDINGS: ON 12 WIDE BUILDINGS GIRTS ARE 67 3/4 LONG ON 20 WIDE BUILDINGS GIRTS ARE 56 3/4 LONG ON 24
More informationProduct Instruction Booklet
Product Instruction Booklet Contents: Page No. Pack Mount: This the set up that most people start with. 1 CARB Spout: Designed to reduce the chance of spilling as well as reducing the emissions of harmful
More informationInstallation Instructions. Oakmont Folding Doors
Before You Start For quick and easy installation of your Oakmont folding door, read these instructions thoroughly. A few minutes of prior planning will make the job easier and ensure years of trouble-free
More informationInstallation - Sub Cills
Installation - Sub Cills Fitting of Subcill Drainage paths through the sub-cill can be seen on the illustration alongside so care must be taken to ensure they are not obstructed and that screw fixings
More informationpatio door installation guide
patio door installation guide Measuring & surveying p2 Mechanical jointing p5 Installation p5 Hardware adjustment p7 Sealing of outer frame p7 Cleaning p7 Walk through clearances p8 Minimum and maximum
More informationHahn AT-G. The simple hinge for light aluminium doors. Quick secure Wide variety of uses
Hahn AT-G The simple hinge for light aluminium doors! Quick secure Wide variety of uses 2 Hahn AT-G The simple hinge for light aluminium doors Constructed of extruded aluminium well-suited to withstand
More informationTable and Furniture Base Fittings Plinth Adjusting Fittings
Adjusting screw with M8 or M thread Rigid, for glide inserts, steel thread Finish/Colour: Black, thread galvanized Version: With acceptance Ø30 mm Thread M8 650.22.381 M 650.22.382 Packing: 1 or 0 pcs.
More informationPiazzola Pergola Awning Manufacturing and installation guide
Piazzola Pergola Awning Manufacturing and installation guide Date Changes Page General information Maximum and minimum width Width Projection 150 to 349 cm 350 to 500 cm From 200 to 250 cm X From 251 to
More informationYALE FIGURE 500 & 500R CLOSURE OPERATION AND MAINTENANCE INSTRUCTIONS
YALE FIGURE 500 & 500R CLOSURE OPERATION AND MAINTENANCE INSTRUCTIONS IMPORTANT INFORMATION Note To Supervisor: Please share this information with your employees and make sure they have received training
More informationFAVORIT Si-line - KF 3
Turn/tilt fitting for single sash PVCu windows with 2 mm air gap Botm tilt point - finish TS silver - handle height variable/centre 34 25 24 3 7 3 2 23 22 20 3 4 6 2 8 3 5 FKgb033_3_0.04/ printed on chlorine-free
More informationModel 20: Home & Garden Cart
Model 20: Home & Garden Cart Parts List Step 1: A: Install two ¾ Bolts (C) through the rear trim piece on the Bottom Panel (S) and attach to Lock Nuts. (Lock nuts on bottom side) B: Place left Side Panel
More informationPREASSEMBLED ELEMENTS FOR LIFTING AND SLIDING DOORS
PROFILE SYSTEM PRE-ASSEMBLED ELEMENTS FOR LIFTING AND SLIDING DOORS s r ood gni d i l s dna gni t f i l r o f s t neme l e de l bme s s a - er P PREASSEMBLED ELEMENTS FOR LIFTING AND SLIDING DOORS MINITEC
More informationFor Euro grooves and NC International profiles
RIBANTA For Euro grooves and NC International profiles - All accessories are frontally applied - Connection rods are modular and provided already pre-cut to standard sizes - All parts are pre-assembled
More informationStorefront Installation Guide INSTALLATION INSTRUCTIONS
STOREFRONT General Notes 1. Check contract documents and shop drawings, and understand and clarify any Field Verify Notes, approvals of drawings, and products required to be familiar with the project.
More informationHDL(M)6 Nut/Screw Assembly
HDL(M)6 Nut/Screw Assembly Remove, repair, and reassemble the nut and screw assembly in your HDL series double lock vise. In these instructions when we refer to the front of the vise or nut/screw assembly,
More information14/08/15 AVAILABLE FROM MIDRAND RANDBURG DURBAN UMHLANGA MARGATE CAPE TOWN GHANA
4/08/5 AVAILABLE FROM MIDRAND RANDBURG DURBAN UMHLANGA MARGATE CAPE TOWN GHANA PINETOWN BALLITO KRABY DROP DOWN with Kimana Hinges (pg 3) For further information: www.italianaferramenta.com > CATALOGUE
More informationSpring Loaded SCREEN-PRO. All Season Roll-Up Doors IN-JAMB MOUNTING METHOD INSTALLATION INSTRUCTIONS READ THIS FIRST
Spring Loaded SCREEN-PRO All Season Roll-Up Doors IN-JAMB MOUNTING METHOD INSTALLATION INSTRUCTIONS READ THIS FIRST Carefully examine the crate(s) for damage before opening. If the carton is damaged, immediately
More informationHeavy Duty Ceiling Tilt Mount Installation Manual
HD-CTM-5580 Heavy Duty Ceiling Tilt Mount Installation Manual *This Installation requires a minimum of two people. For your safety: Read the complete instruction manual before starting an installation
More informationHQ Pole Upgrade Kit for HQ Adjustable Table and HQ QuilTable Assembly Instructions 1
HQ Pole Upgrade Kit for HQ Adjustable Table and HQ QuilTable Assembly Instructions QF09775 The pole upgrade kit can be used with or without the QF09700 HQ Precison-Glide track upgrade kit. What s Included
More information3.2.3 Rear Door Window and Quarter Window Carrier Assembly
Tighten all bolts. Tighten bolts marked -1- and -2- in specified sequence. Tightening torque: 8 Nm Remaining bolts can be tightened in any sequence. Insert door window -3- through window recess without
More informationWeatherfold 4s 50 & 100 Brio Australia P: W: brio.com.au
Codes INSTBWS2 REV J - MAR 2017 Weatherfold 4s 50 & 100 Brio Australia P: +61 2 87186718 W: brio.com.au E: brio.sales@allegion.com Brio UK P: +44 191 2291224 W: briouk.com E: brio.sales.uk@allegion.com
More informationTechnical Documentation Lift Advanced
Technical Documentation Lift Advanced 1 1 Introduction... 4 2 Basic Information... 5 2.1 Hinge Recommendations... 5 Lift Advanced HF... 5 Lift Advanced HK... 5 2.2 Usage of Aluminium Fronts... 5 19mm Aluminium
More informationINSTALLATION INSTRUCTIONS 3 BULL BAR 99-04, 04 "HERITAGE" F-150/250LD 2WD, 97-04, 04 "HERITAGE" 4WD WD EXPEDITION/ WD EXPEDITION PART
INSTALLATION INSTRUCTIONS 3 BULL BAR PART #B-F1971;B-F2971 PARTS LIST: 1 Bull Bar 2 12-1.75mm x 130mm x 40mm Hex Bolts 1 Driver/Left Mounting Bracket 4 12-1.75mm x 35mm Hex Bolts 1 Passenger/Right Mounting
More informationKitchen Fittings Hanging Cabinets and Accessories
Cabinet hanger Knock-in version, load bearing capacity 130 kg/pair Depth adjustment Finish: Galvanized Concealed mounting of cabinet hanger behind the rear panel (Min. 16 mm free space required) Mounting
More informationTOOLS REQUIRED: HARDWARE INCLUDED: 13MM FLAT WRENCH FOR LEVELING THE STRUCTURE RATCHET WITH 5MM HEX BIT FOR CORNER SCREWS ON TOP TRAVERSE BEAMS
1 TOOLS REQUIRED: RATCHET WITH 5MM HEX BIT FOR CORNER SCREWS ON TOP TRAVERSE BEAMS 13MM FLAT WRENCH FOR LEVELING THE STRUCTURE RUBBER MALLET FOR INSERTING PANELS 8MM HEX BIT WITH EXTENSION FOR HEX BOLT
More informationSteele TV Stand Stock # BH
LOT NUMBER: DATE PURCHASED: / / Steele TV Stand Stock # BH46-084-899-02 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store
More informationLeveling Feet, Base Plates and Casters
Leveling Feet, Base Plates and Casters 77 Leveling Foot 1 1 Fastening to profile end Fastening in T-slot of profile For leveling tables and light equipment. Ratchet-type height adjustment requires no tools.
More informationFABA. Installation Instructions. Conductor Bar System. Publication #FABA-03 3/1/04 Part Number: Copyright 2004 Electromotive Systems
FABA Conductor Bar System Installation Instructions Publication #FABA-03 3/1/04 Part Number: 005-1062 Copyright 2004 Electromotive Systems 1S 100 Z Installation Instructions Contents: Basic Diagram - -
More informationSM-RAZOR-T-M/L/XL. Strong Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTRUCTION MANUAL
SM-RAZOR-T-M/L/XL Strong Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTRUCTION MANUAL WARNINGS: Installation of this product should be done by a qualified professional. Do not begin installation
More informationPocket Door Kit PD1 / PD2 Installation Instructions. Kit Contents.
Pocket Door Kit PD1 / PD2 Installation Instructions Kit Contents. 1, Create Rough Opening In Stud Wall Construct rough opening ensuring all sides are square and level. Rough opening should be; Height =
More informationP.O. Box 8400 Green Bay, WI (920)
P.O. Box 8400 Green Bay, WI 54308-8400 (920) 468-2165 Change Notice No. 112 Implemented By: KI-Pembroke Notification By: Scott Vissers Date: 03/15/10 Component Product Title: Series XXI Lateral Filing
More informationB-Too Drilling and Tapping Machine Instruction and Maintenance Manual
B-Too Drilling and Tapping Machine Instruction and Maintenance Manual Thank you for your purchase of the B-Too Drilling and Tapping Machine. Please read and understand this short operation manual. Our
More informationINSTALLATION INSTRUCTIONS FOR A&L PRODUCTS
INSTALLATION INSTRUCTIONS FOR A&L PRODUCTS AUGUST 2017 1 RECOMMENDED BUILDING IN-DETAIL Should you require further information, please contact A&L Windows on 1800 441 414 2 IMPORTANT IMPORTANT Allow Vinyl
More informationInstallation of HORIZONT and HORIZONT HIGH pool enclosures
Installation of HORIZONT and HORIZONT HIGH pool enclosures Rev. 19.10.2017 PARTS LIST Parts for rail installation: Rail screw 6 x 60 Plastic anchor 10 x 50 Rail connector Arrest wedge [R-L] Pop rivet 4
More informationMS25 OPERATION MANUAL
SAFETY INSTRUCTIONS SPECIFICATIONS OPERATING INSTRUCTIONS MAINTENANCE ADJUSTMENTS REPLACEMENT OF PARTS MS25 DIAGRAM MS25 PARTS LIST MS25 OPERATION MANUAL SAFETY INSTRUCTIONS Please read these instructions
More informationTOTAL HARDWARE COMPETENCE. Roto NT. FB 28-0 GB January 2002 BKWK / Saile
TOTAL HARDWARE COMPETENCE 1 THE SURFACE TREATMENT: ROTOsil Process: similar to ROTOnor Zinc plated Chromate Dipping (ROTOsil) Advantage: Optically superior in mattsilver Environmentally friendly Corrosion
More informationUsage and Assembly Instructions
Instructions #1037447 Product #795234 Revision D Usage and Assembly Instructions Rear Fork (Buttstock) Rear Fork Lock Knob Rail Lock Knob Front Fork (Forend) Rails Tilt Friction Knob Rail Extension Locks
More informationRevised
Indentify Non-powered panels and separate from Powered panels. Non-powered panel shown at left.. Powered panel shown at left has powerway mounted at factory. Also separate panels by surface type, width
More informationLEGENDS RETRACTABLE DOOR SCREENS
LEGENDS RETRACTABLE DOOR SCREENS MAGNETIC LATCHING DESIGN SYSTEM 42 I N S T A L L A T I O N I N S T R U C T I O N S 1 MOUNTING OPTIONS Recess : Mount the Screen Cassette using Recess Mounting Clips Recess
More informationOSBORNE SHOWER DOOR INSTALLATION
SKU(s): 939719, 939720, 939721 OSBORNE SHOWER DOOR INSTALLATION BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing this type of product. Signature Hardware accepts
More informationCOUPLING. When apertures are too large for single window units then frames need to be coupled together.
When apertures are too large for single window units then frames need to be coupled together. The procedure is typical for all the open out, open in and sliding systems whether Classic, Antik or Design
More informationSIG Awning / Casement / Fixed Lite 100
TYPICAL FRAME ASSEMBLY - AWNING WINDOW 07-01 85720-2 GASKET EXT FL JAMB 100 BS201 (3471) HEAD HINGED 100 86064 TRIM FIN A 83963 SCREW SQ 8G X 1.0 PAN PP SS #2 85737 GASKET EXT FL TRANSOM 85720-1 86065
More informationWINDOW TECHNOLOGY ORDER CATALOG SECTION Tilt&Turn Hardware UNI-JET D PVC
WINDOW TECHNOLOGY ORDER CATALOG SECTION 06.1 Tilt&Turn Hardware UNI-JET D PVC Table of Contents 06.1 UNI-JET D PVC 06 1 DIRIGENT T&T Handle...06.1.9 Tilt&Turn...06.1.10 Turn-Only Sash...06.1.14 Dummy-mullion
More information