Piazzola Pergola Awning Manufacturing and installation guide

Size: px
Start display at page:

Download "Piazzola Pergola Awning Manufacturing and installation guide"

Transcription

1 Piazzola Pergola Awning Manufacturing and installation guide Date Changes Page

2 General information Maximum and minimum width Width Projection 150 to 349 cm 350 to 500 cm From 200 to 250 cm X From 251 to 600 cm X X Maximum fabric surface 30 m² per awning section (acrylic fabric, Tibelly). To confection the fabric, a wide side hem of 10 cm should be used at both fabric sides. The front profile will start to bend at a free span of 4 m or more. This has no effect on the functionality of the system. You can opt for an arched front profile or a coupled system with two shorter front profiles. Fabric winding method: Bottomwise. Reference item ±10 70 Projection Length side guide Oversize side guide max. 1m Passage height "A" Awning height to reference item 23,3 Cut sizes Control by ASA motor Fabric roller -57 mm -61 mm Bottom cover Top cover Wall cover Upper front profile Lower front profile Side guide Water gutter Post Support beam Support beam (fabric support) Fabric -21 mm -22 mm -0 mm -176 mm -175 mm Projection 270 mm Control by Somfy motor Length side guide + 36 mm (when using part nbr ) Standing height + length A -10 mm (when using part nbr ) Standing height + length A + length below ground level -154 mm -10 mm -155 mm 2 Piazzola Pergola Awning Version 1.01

3 General information Motor diagram For a single unit use 40 Nm. For a double unit (2 linked units) use 80 Nm. Notes Place an extra support beam to support the fabric upward a projection of 3.50 m. When using the Piazzola, in case of rain (short light rainfall) we always recommend (a) support beam(s) supporting the fabric and apply a lock set. The Piazzola should then be placed at a minimum angle of 17 degrees. For a better drainage one can choose to place rings in the fabric. Overview of drawings In the undermentioned overview two drawings are visible with important sizes. Angle connection in mm 75 37,5 37, ,5 75 Side view wall mounting in mm 9 233, ,9 73, ,3 Version 1.01 Piazzola Pergola Awning 3

4 1. Cut the length material into the correct size (see table cut sizes). 2. On the operating side, drill a hole of 11 mm in the bottom cover for lead-through of the motor cable. Fit a tulle in this hole. 12. Place the motor into the control side of the steel tube, and insert the bearing plug on the bearing side. Cord length per side: 2x the projection plus 1.5 times the width plus 1 m. 3. Around the centre point of the length, drill a hole of 6.5 mm along the drill line in the groove of the bottom cover for placement of the top cover support. Note: No wall bracket can be placed here. 4. Slide the mounting plate with sockethead screws in the same groove. Turn 1 socket-head screw through the hole of 6.5 mm. Tighten the other socket-head screws. 13. Make 4 windings of cord on the cord pulley and ensure that the cord runs neatly. TIP: Apply double sided tape in the cord pulley before winding the cord. The first 4 windings will then be fixed in place and will remain so during transport. 14. Assemble the top cover supports (bearing side and control side) as shown on the figure. 5. Slide the wall brackets into the bottom cover. Place the outside brackets at 10 mm from the outside of the bottom cover. 6. A third bracket is required if the width > approx m. It should be placed more or less in the middle. 7. Using screws, fasten all wall brackets to the bottom and backside. 8. Pull the plastic insert strip into the bottom cover. 15. Use screws to fasten both top cover supports to the bottom cover. 16. Place the cord pulleys opposite the wheels on the top cover supports and fix these into place. 9. Slide the two PVC inserts into the fabric. 10. Wind up the fabric on the fabric roller. 11. Fit the cord pulleys. 4 Piazzola Pergola Awning Version 1.01

5 17. Hook the cover support into the bottom cover and place it alongside the socket-head screw that is projecting through the cover. 28. Drill 6.5 mm holes in the left and right side guide for fastening to the top cover supports. 6,5 18. Hook the top cover into the bottom cover and use screws to fasten it to the ends of the top cover supports. 19. Attach the cord tensioners at 50 cm from the centre on the sloping side of the lower front profile. Note: Cord tensioners come in left and right versions. 20. Slide the central pulley into the opening in the lower front profile. 21. Slide the front profile onto the fabric. 22. Fasten the guide blocks onto the lower front profile using screws Slide the mounting plate of the fabric support into the side guide, place it in the required position, and use it to fasten the support. 30. Slide the mounting plate of the top hinge into the side guide. Fasten the top hinge at the required position of the side guide. Leave space for the nut on the outside. 31. Insert the guide plate into the top of the side guide and slide into place. Use a rubber hammer to tap firm. Note: If the lock set is used, it can be mounted now (see number 66) The support consists of two posts with hinge and footplate connected to a support beam. 24. Drill two holes into the post as shown in the figure (page 3 angle connection). 25. Use a machine screwing tap M8 to tap a thread in the post and support beam. Provide sufficient lubrication. Minimum tap 25 mm. 26. Screw the socket-head bolt M8x50 on both sides of the support beam. Let it oversize for ±15 mm. Insert the socket-head bolts through the holes in the post and tighten them. 27. Screw the bottom hinge at the top of the post and the baseplate at the bottom. 32. Take the water gutter sections and drill holes of 5 mm at intervals of ± 60 cm along the drill line. 33. Screw a cover plate against the front of the water gutter. 34. Hook the water gutter sections into the side guide, keeping the cover plate on the front even with the front of the side guide, and screw into place. #25 # Fasten the mounting plate to the wall at a distance that is equal to the length of the awning, measured on the outside (when using a wall cover, deduct the thickness of the endplate of the wall cover = 6 mm). Version 1.01 Piazzola Pergola Awning 5

6 36. Hook the wall brackets into the mounting plate and fasten the socketplate screws on the bottom side. 43. Tighten the nuts on the side of the wall bracket. 37. Pull out the front profile by 30 cm. 38. Feed the cord along the wheels of the guide blocks into the front profile. 39. Slide the side guide over the wheels of the guide blocks and over the leg of the top cover support. 44. Hook the springs on the left and right into the screw eyes of the guide blocks. 45. Place the pulley on the other side of the spring. 46. Slide the central pulley towards the centre of the bottom front profile. 47. Lead the cord through the side guide and lay it over the top of the wheels in the end bearing. Ensure that the cord is not crossed in the side guide. 48. Lead the cord as shown in the figure below. Pull out each spring to a maximum of 60% of its own length. 40. Attach the side guide to the legs of the top cover supports. 41. Place the two hinges at the desired positions above one another, and connect these. 42. Measure the Piazzola diagonally and ensure that the system is perfectly perpendicular. When using concrete pads, place the posts at exactly the same height. When using the baseplate, fasten it to the ground. 49. Tension the springs lightly. 50. Check that the cord runs well over all the wheels of the pulleys. 51. Further tension the springs by pulling the cord in the cord tensioners. 52. Allow the fabric to run out to its full length. 53. Determine at which point of the side guide the springs are least tensioned. This is the point where the awning will sag. 54. Then mark the position of the front profile in relation to the side guide. 55. Stop the front profile at the marked point while drawing in. 56. Tension the springs in such a way that the fabric is (sufficiently) tight. For this, pull the cord in the cord tensioners. 57. Let the awning run in and out a couple of times to check correct functioning 58. Straighten the top cover by turning the sockethead screw at the back of the bottom cover. 59. Attach the wall cover and wall cover end plates to one another. 60. Pull the plastic insert strip into the gulley of the wall cover and fasten the end plates using screws. 61. Place the wall cover on the top cover and position the end plates even against the wall. 6 Piazzola Pergola Awning Version 1.01

7 62. Determine the position of the holes and drill these in the wall cover and wall. 63. Attach the wall cover to the wall and the end plates to the mounting plate (bottom slot end plate). 64. Hook the cover extension into the top cover. 65. Drill holes in the cover extension and the side guides. 66. Attach them to one another using screws. 67. The lock set can only be used with an ASA ETR-A or a Somfy Orea motor. Place the lock set at least 110 mm from the end of the side guide. At this place no top hinge can be mounted. The plastic stopper has to be screwed on the front profile, as shown at the drawing. Note: At this place no top hinge can be mounted Version 1.01 Piazzola Pergola Awning 7

8 Piazzola Pergola Awning Pergola Awning Piazzola Exploded-view Version 1.01

9 Hexagon nut M8 stainless Flat washer without shamfer M8 stainless A Lock set Piazzola Neopren strip 10x2mm selfadhesive Reinforcement corner set Piazzola Cover reinforcement corner Piazzola Hexagon socket set screw M6x10 stainless Mounting plate Piazzola Cord tensionner, left Self drilling pancil. screw with Philips Head ST4,2x Cord tensionner, right Countersunk plate screw with Philips Head ST4,2x45 stainless / 185 Spring 25mm, length 350mm / 570mm Guide block Piazzola left Screw eye with nut M Stainless pulley for cord 2,5mm with synth. runner Guide block Piazzola right Central pulley for cord 2,5mm Alu upper front profile Summerlight Alu lower front profile Summerlight Flat washer without shamfer DIN A M6 stainless Hexagon bolt M6x20 stainless Guide plate Piazzola left Cylinder hexagon screw M6x16 stainless Side guide Piazzola Hinge Piazzola upside Cylinder hexagon screw M6x20 stainless Guide plate Piazzola right Clamping plate Piazzola stainless Bearing block set Piazzola, Cubola, Summerlight End plate for end bearing Piazzola Plate screw with countersunk Philips Head 3,5x16 mm Cover plate gutter Piazzola Gutter side guide Piazzola Pancil. Plate screw with Philips Head ST4,2x Synth. sealing strip Cover plate for wall cover Piazzola Wall cover Piazzola Support set intermediate support beam Piazzola Support beam Piazzola (fabric support) Support beam Piazzola Lower hinge Piazzola Adjustment hexagon screw M8x50mm Cylinder hexagon screw M8x70 stainless Cylinder hexagon screw M8x30 stainless Socket head bolt M8x30 countersunk Philips Head Base plate Piazzola Post Piazzola Fabric Drilling screw 4,2x13 DIN 7504 stainless A Adaptor ASA / Somfy Friction ring ASA / Somfy Steel tube Synth. cord pulley tube Synth. Washer 16mm Countersunk plate screw with Philips Head ST4,2x32 stainless Synth. bearing bung 85 with axle ASA / Somfy motor Bristle for top cover Alu motor support ASA / Somfy Synth. bearing block complete Cover support Piazzola Top cover support Piazzola left complete Top cover support Piazzola right complete Wall bracket Piazzola Mounting plate Gota 140mm Top cover Piazzola Bottom cover Piazzola 1 No. Part number Description Nbr. Parts list Version 1.01 Piazzola Pergola Awning 9

Manufacturing and installation instruction. Solidare Verso. Pergola awning (bottom mounted)

Manufacturing and installation instruction. Solidare Verso. Pergola awning (bottom mounted) Manufacturing and installation instruction Solidare Verso Pergola awning (bottom mounted) Solidare Verso pergola awning 11-05-2017 * * A T T E N T I O N * * AVZ accepts no liability for any errors in this

More information

SolidScreen XL. Version 1.05 Sun Protection AVZ 6P.1

SolidScreen XL. Version 1.05 Sun Protection AVZ 6P.1 Version 1.05 Sun Protection AVZ P.1 P.2 Sun Protection AVZ Versie 1.05 4453 470-000 End fix bracket Screen 150 square without spindle, left Mill finish 4453 472-000 Idem, right Mill finish 4453 470-008

More information

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

Installation Guide Simplicity Alfresco. V1.9 Lu070318

Installation Guide Simplicity Alfresco. V1.9 Lu070318 0333 305 5272 www.canoports.co.uk Installation Guide Simplicity Alfresco V1.9 Lu070318 Tools Required Below is a list of tools that you will require to install your the Simplicity Alfresco System. Cordless

More information

GROWING BETTER THROUGH DESIGN. 6ft Lean-To LEAN-TO. Assembly Instructions 04/02

GROWING BETTER THROUGH DESIGN. 6ft Lean-To LEAN-TO. Assembly Instructions 04/02 GROWING BETTER THROUGH DESIGN 6ft Lean-To LEAN-TO Assembly Instructions 04/02 6ft Lean-To Greenhouse Base Plan Introduction/Tools/Contents / / Contents This is a copy of our Lean-To greenhouse base plan.

More information

GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)

GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS

400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS 12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions

More information

Installation Guide Contemporary Alfresco V1.3 LU

Installation Guide Contemporary Alfresco V1.3 LU Installation Guide Contemporary Alfresco V1.3 LU 010818 Tools Required Below is a list of tools that you will require to install you're the Contemporary Alfresco System. Cordless Drill Mastic Gun Spirit

More information

AX1001. Smith/Functional training Combo-free weight ASSEMBLY INSTRUCTIONS

AX1001. Smith/Functional training Combo-free weight ASSEMBLY INSTRUCTIONS AX1001 Smith/Functional training Combo-free weight ASSEMBLY INSTRUCTIONS EXPLODED DIAGRAM 83 84 84 85/86 87 87 88 89 90 91 62 64 64 64 64 64 64 65 65 65 65 66 66 65 66 66 65 63 63 66 67 68 55 66 66 70

More information

set of safety brace steel cable draw-up gate kpl

set of safety brace steel cable draw-up gate kpl 0324101 7108020 8208100 Order-nr. Description Number 0324101 safety brace steel cable draw-up gate 2 7108020 hexagon-head tap bolt M8x20 galv. 2 8208100 hexagon nut M8 galv. 2 set of safety brace steel

More information

CHICKEN COOP & CHICKEN RUN. Tools required for assembly (not included)

CHICKEN COOP & CHICKEN RUN. Tools required for assembly (not included) CHICKEN COOP & CHICKEN RUN ASSEMBLY MANUAL SKU# 6839 Tools required for assembly (not included) Distributed by: TRACTOR SUPPLY COMPANY 0 VIRGINIA WAY, BRENTWOOD, TN 3707 For customer support, call: -888-376-960

More information

Deck Mount Installation with Bench

Deck Mount Installation with Bench Deck Mount Installation with Bench 1. Mark track with square. 2. Cut tracks with saw. 3. Drill ¼ hole (if needed.) 4. Countersink track. 5. Countersink all track 6. File all track ends. ends. 7. Lay out

More information

TELESCOPIC GATE MANUFACTURING AND INSTALLATION MANUAL.

TELESCOPIC GATE MANUFACTURING AND INSTALLATION MANUAL. TELESCOPIC GATE MANUFACTURING AND INSTALLATION MANUAL. Telescopic gates have been manufactured for many years essentially in the same way they are largely today. In recent years hardware suppliers have

More information

AWNING / PATIO COVER INSTALLATION INSTRUCTIONS

AWNING / PATIO COVER INSTALLATION INSTRUCTIONS AWNING / PATIO COVER INSTALLATION INSTRUCTIONS Before You Begin Read the installation instructions thoroughly before beginning the installation procedure. Perspective In the Awning Instructions, Back means

More information

Dublin Stalls Installation Instructions

Dublin Stalls Installation Instructions Dublin Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 9/13/17 Part Identification Round Track Bracket (4) (Not Painted) Round

More information

Clearview Railing System Installation Instructions

Clearview Railing System Installation Instructions Clearview Railing System Installation Instructions Disclaimer: AGS Stainless, Inc. has its Clearview Railing Systems designed by a professional engineer to meet the requirements of the latest national

More information

aluminium profile system

aluminium profile system aluminium profile system 63 AME System aluminium profiles overview series profiles introduction 80x80 x80 x80/180 x Aluminium profiles are provided with longitudinal grooves which can be used in conjunction

More information

ASSEMBLY INSTRUCTIONS FOR 9000 DOOR

ASSEMBLY INSTRUCTIONS FOR 9000 DOOR ASSEMBLY INSTRUCTIONS FOR 9000 DOOR SLI Nassau Door A/S Krogagervej 2 DK-5750 Ringe Tlf.: +45 62 62 23 46 Fax: +45 62 62 39 18 E-mail: info@nassau.dk www.nassau.dk MANUAL NO.: 89-22021 / RELEASE 8 CONTENTS

More information

Pergola Installation Instructions

Pergola Installation Instructions Pergola Installation Instructions TOOLS REQUIRED HAMMER DRILL 1/2 MASONRY BIT PENCIL DRILL 3/16 DRILL BIT LEVEL SQUARE LADDER WRATCHET & SOCKETS RUBBER MALLET 2 TAPE MEASURE Column/Post Placement Table

More information

MAG-CONV Basic, 48, 48R & Midline Front Mount

MAG-CONV Basic, 48, 48R & Midline Front Mount Parts Required: Tools Used: Mag Wheels Brakes Brake Rods Mounting Bracket Anti Tippers 7/16" Wrench Screw Driver Rubber Mallet 5/8 Wrench 5mm Allen Wrench Step Execution Figures 1 Remove front 5" total

More information

Thank you for purchasing out product! *Please read these instructions and follow them step by step. *

Thank you for purchasing out product! *Please read these instructions and follow them step by step. * Page 1 of 7 AD17 AA DS 4 X 16 T12 Thank you for purchasing out product! *Please read these instructions and follow them step by step. * STEP 1. Slide two support posts (REF. # 24) into the two outside

More information

SPARE PARTS LIST MODEL NO. LB1200F PAGE 1 ITEM PART NO. DESCRIPTION QTY NOTE

SPARE PARTS LIST MODEL NO. LB1200F PAGE 1 ITEM PART NO. DESCRIPTION QTY NOTE PAGE 1 001 JM21000018 HEX.SOCKET HEAD SCREW M5X12 4 002 JM21000019 SPRING WASHER 5 4 003 JM21000020 FLAT WASHER 5 4 004 JM21000021 UP COVER COMPLETE 1 005 JM21000025 MICRO SWITCH FIX PANEL A 1 006 JM21000026

More information

Gota cassette. Version 1.10 Sun Protection AVZ 3G.1

Gota cassette. Version 1.10 Sun Protection AVZ 3G.1 Version 1.10 Sun Protection AVZ G.1 G.2 Sun Protection AVZ Version 1.10 Part number Description Paint finish Length in m 1 4211 772-090 Alu wall bracket 140 mm Mill finish 4211 772-008 Idem RAL 705 light

More information

PRS X-Axis E-Chain Installation For Tools with a 12 Z-Axis

PRS X-Axis E-Chain Installation For Tools with a 12 Z-Axis 888-680-4466 ShopBotTools.com PRS X-Axis E-Chain Installation For Tools with a 12 Z-Axis This kit is compatible with PRS Shopbots that have an X-axis cutting area of 96 to 144. It is not immediately compatible

More information

VINYL CLASSIC FREESTANDING PERGOLA ASSEMBLY INSTRUCTIONS

VINYL CLASSIC FREESTANDING PERGOLA ASSEMBLY INSTRUCTIONS P a g e 1 VINYL CLASSIC FREESTANDING PERGOLA ASSEMBLY INSTRUCTIONS Shown: 8' x 12' Vinyl Classic Pergola with 12" Top and Main Runner Spacing The design of this pergola is based on all posts being installed

More information

PORTA-DOCK, INC. AP17 APD DS 4 X 16 T12 AW17 CPD DS 4 X 16 T12

PORTA-DOCK, INC. AP17 APD DS 4 X 16 T12 AW17 CPD DS 4 X 16 T12 Page 1 of 7 PORTA-DOCK, INC. AP17 APD DS 4 X 16 T12 AW17 CPD DS 4 X 16 T12 *For Beige Decking Add the Letter B to Model* Thank you for purchasing out product! *Please read these instructions and follow

More information

STANDARD GRAVITY BOX TARP INSTALLATION

STANDARD GRAVITY BOX TARP INSTALLATION OPERATORS MANUAL Rev. 9.9.2016 STANDARD GRAVITY BOX TARP INSTALLATION J. & M. Mfg. Co., Inc. 284 Railroad Street - P.O. Box 547 Fort Recovery, OH 45846 Ph: (419) 375-2376 Fax: (419) 375-2708 www.jm-inc.com

More information

CONTENTS TOOL LIST U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS. Revised: June 2013

CONTENTS TOOL LIST U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS. Revised: June 2013 U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS TOOL LIST Required Tools: - Reciprocating Saw with Metal Cutting Blade - Drill - 7/16 Drill Bit for Metal Drilling -

More information

A59 APD & A86 CPD 5'X 16' SW ALUMINUM PORTA-DOCK

A59 APD & A86 CPD 5'X 16' SW ALUMINUM PORTA-DOCK Page 1 of 5 PORTA-DOCK, INC. A59 APD & A86 CPD 5'X 16' SW ALUMINUM PORTA-DOCK *For Beige Decking Add the Letter B to model* Thank you for purchasing our product! *Please read these instructions and follow

More information

V4 Premium Kit. Prusa i3 Build Guide

V4 Premium Kit. Prusa i3 Build Guide V4 Premium Kit Prusa i3 Build Guide Hi! Congratulations on your purchase of the DIYElectronics.co.za Prusa I3 kit, the best South African 3D Printer Kit! Hopefully this should serve as complete guide to

More information

ASSEMBLY AND ADJUSTMENT

ASSEMBLY AND ADJUSTMENT EPPA MONITOR ARM EPPA Rev A 10/17 Model EPPA-XXX ASSEMBLY AND ADJUSTMENT EPPA MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment procedures. Check

More information

Table and Furniture Base Fittings Plinth Adjusting Fittings

Table and Furniture Base Fittings Plinth Adjusting Fittings Adjusting screw with M8 or M thread Rigid, for glide inserts, steel thread Finish/Colour: Black, thread galvanized Version: With acceptance Ø30 mm Thread M8 650.22.381 M 650.22.382 Packing: 1 or 0 pcs.

More information

S48-L12-SC AND G48-L12-GC STEEL PORTA-DOCK S82 SC 6 X 12 PLATFORM AND G82 GC 6 X 12 PLATFORM

S48-L12-SC AND G48-L12-GC STEEL PORTA-DOCK S82 SC 6 X 12 PLATFORM AND G82 GC 6 X 12 PLATFORM PAGE 1 OF 6 PORTA-DOCK, INC. S48-L12-SC AND G48-L12-GC STEEL PORTA-DOCK S82 SC 6 X 12 PLATFORM AND G82 GC 6 X 12 PLATFORM Thank you for purchasing our product! *Please read these instructions and follow

More information

Taurean Sectional Garage Door INSTALLATION INSTRUCTIONS

Taurean Sectional Garage Door INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN MAKE SURE THESE INSTRUCTIONS ARE READ AND UNDERSTOOD COMPLETELY. THESE INSTRUCTIONS ARE INTENDED FOR PROFESSIONAL GARAGE DOOR INSTALLERS. ALL REFERENCES ARE TAKEN FROM THE INSIDE LOOKING

More information

Assembly Instructions 10 X 10 Aluminum Roof Support

Assembly Instructions 10 X 10 Aluminum Roof Support Assembly Instructions 10 X 10 Aluminum Roof Support Aluminum Roof Support Bolt Package 16-5/16 X 2 ¼ SS Bolt 24-5/16 X 1 SS Bolt 40-5/16 SS Nylon Lock Nuts 16-5/16 SS Flat Washers 28-4 ½ Wood Screws 36-1

More information

Depending on the size you ordered you will have either 5 Foot sections which will build the 10 Foot frame or 6 Foot sections which will build the 12

Depending on the size you ordered you will have either 5 Foot sections which will build the 10 Foot frame or 6 Foot sections which will build the 12 XL Quilting Frame 1 Depending on the size you ordered you will have either 5 Foot sections which will build the 10 Foot frame or 6 Foot sections which will build the 12 Foot frame Printed 2 June 2014 Updated

More information

INSTALLATION INSTRUCTION RRU DOUBLE LIGHT POLE MOUNT

INSTALLATION INSTRUCTION RRU DOUBLE LIGHT POLE MOUNT INSTALLATION INSTRUCTION RRU Double Light Pole Mount for installation of two RRU units on mast, towers or other vertical structures. CUE DEE YOUR INNOVATIVE PARTNER 1 CONTENTS 1. PRODUCT COVERED IN THIS

More information

F i t t i n g t h e N e w L a n d i n g G e a r t o Y o u r S k y J i b V 1

F i t t i n g t h e N e w L a n d i n g G e a r t o Y o u r S k y J i b V 1 F i t t i n g t h e N e w L a n d i n g G e a r t o Y o u r S k y J i b V 1 1 P a r t s L i s t : S t a n d a r d L a n d i n g G e a r U p g r a d e Product Code Parts + Spares Product Code Parts + Spares

More information

Titan Series Awning Assembly and Installation Instructions

Titan Series Awning Assembly and Installation Instructions Titan Series Awning Assembly and Installation Instructions Be sure to use safety glasses when assembling and installing the awning. Some metal parts may have sharp edges. Use work gloves to handle them.

More information

CRP700 Benchtop Basic CNC Machine Assembly Instructions. Updated 10/24/2014 SHEET 1 of 24

CRP700 Benchtop Basic CNC Machine Assembly Instructions. Updated 10/24/2014 SHEET 1 of 24 CRP700 Benchtop Basic CNC Machine Assembly Instructions Updated 0//0 SHEET of NOTE: This piece of extrusion is mounted wide side up Quick Tip: Lay extrusion on table as shown for easy assembly BASE ASSEMBLY:.

More information

1: profile cross section. FD- profile. for sidewalls + backwalls. eaves profile. curved roof profile. Z - profile (alongside frame) L 60 x 60

1: profile cross section. FD- profile. for sidewalls + backwalls. eaves profile. curved roof profile. Z - profile (alongside frame) L 60 x 60 1: profile cross section FD- profile for sidewalls + backwalls eaves profile curved roof profile Z - profile (alongside frame) L 60 x 60 for backwall Image 2: 1.) Insert feet from below in square tubes

More information

Spring Loaded All Season Roll-Up Doors

Spring Loaded All Season Roll-Up Doors Spring Loaded All Season Roll-Up Doors STAND-OFF MOUNTING METHOD INSTALLATION INSTRUCTIONS READ THIS FIRST Carefully examine the crate(s) for damage before opening. If the carton is damaged, immediately

More information

ENG. Installation instruction. Thermalift 42 TOF, TOR K085129

ENG. Installation instruction. Thermalift 42 TOF, TOR K085129 ENG Installation instruction Thermalift 2 TOF, TOR K08129 0706 EC-DECLARATION OF producer We hereby declare that the following described product, with regard to its conception and construction and in the

More information

3 D Printer Enclosure Assembly Instructions

3 D Printer Enclosure Assembly Instructions 3 D Printer Enclosure Assembly Instructions Tools Required: 2.5 mm Allen wrench (included) Phillips screwdriver Adjustable Wrench Parts Included: Plexiglas Back with fan and filters installed (29.5 x 35.5

More information

PO BOX 130 CLEAR LAKE, MN

PO BOX 130 CLEAR LAKE, MN WWW.WALKSONWATER.COM PO BOX 130 CLEAR LAKE, MN 55319 320-743-3333 PARTS LIST FOR 30115# VERTICAL BOAT LIFT 2-Back Leg Uprights 1 right, 1 left (BL) 1-Front Leg Upright (FL) 1-Winch Leg Upright (WU) 2-Bottom

More information

Privacy Wall Glass Selections - Polished Edge Slider Door

Privacy Wall Glass Selections - Polished Edge Slider Door Privacy Wall Glass Selections - Polished Edge Slider Door 3/6" HEX BIT PUTTY KNIFE #2 ACR BIT SUCTION CUP HOLDERS DOOR LEAF: Satin Tempered Clear Tempered LOCTITE 425 SIDE LIGHT ETCHED GLASS STYLES: Satin

More information

TITAN2-EDGE Public Access Computer Station Dual Track

TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Rev A 6/17 Model TITAN2-EDGE ASSEMBLY AND ADJUSTMENT TITAN2-EDGE PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the

More information

~11. ~~m. c' Type. W~m IIIIIIIII IIIIIIIII. Tel: (01935) CG 5/9. S. See requirements. BETWEEN BRICKWORK

~11. ~~m. c' Type. W~m IIIIIIIII IIIIIIIII. Tel: (01935) CG 5/9. S. See requirements. BETWEEN BRICKWORK Fitting instructions for c' Type Frame arrangement enin ~~m Width BEHIND BRICKWORK IMPORTANT For electric operation use system 'c' operator. S. See requirements. ~11 BriCkwoJ":ening IIIIIIIII BETWEEN BRICKWORK

More information

Assembly instructions. 6x4. Model GH1354A. 6x6. Model GH1357A. 6x8. Model GH1360A. 6x10. Walk-in Greenhouse. Model GH1363A

Assembly instructions. 6x4. Model GH1354A. 6x6. Model GH1357A. 6x8. Model GH1360A. 6x10. Walk-in Greenhouse. Model GH1363A ssembly instructions x Model GH x Model GH7 x8 Model GH0 x0 Model GH Walk-in Greenhouse Statement ear Customer! May we congratulate you on your new Greenhouse. We feel sure that by following the detailed

More information

Not including the type of fabric used (clear pvc or shade mesh), there are three main types of side screen.

Not including the type of fabric used (clear pvc or shade mesh), there are three main types of side screen. installation Outrigger side screens are installed as a single stage job when the screens are fitted to a existing structure. However, two stages may be necessary if, for whatever reason, reliable measurements

More information

HOUSE PARTS PACKED IN HOUSE BOX PARTS IN PLASTIC BAG (HARDWARE) PARTS IN SMALL PLASTIC BAG (FLOOR CLIPS) PARTS PACKED IN BUNDLE

HOUSE PARTS PACKED IN HOUSE BOX PARTS IN PLASTIC BAG (HARDWARE) PARTS IN SMALL PLASTIC BAG (FLOOR CLIPS) PARTS PACKED IN BUNDLE Check parts against this list before starting assembly. Refer to illustrations on pages 6 and 7 to view house parts. If any shortages are found, refer to Packing Slip for claim instructions. Item 3 5 6

More information

FRONT BUMPER INSTALLATION INSTRUCTIONS Toyota 4Runner

FRONT BUMPER INSTALLATION INSTRUCTIONS Toyota 4Runner Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 FRONT BUMPER INSTALLATION INSTRUCTIONS 2003-2009 Toyota 4Runner Please read before beginning Stainless steel hardware may bind

More information

Assembly instructions

Assembly instructions Commission: Order no.: Rondo Pavilion PR Ø3.9 Technical changes reserved Assembly instructions As at: 05.011 Sliding door Dear Garden lover, we congratulate you on the purchase of a quality product from

More information

NEWS Part. N /0 MINITEC NEWS

NEWS Part. N /0 MINITEC NEWS NEWS 2009 Part. N 95.0423/0 MINITEC NEWS 2009 1 TABLE OF CONTENT INTRODUCTION CONTENTS 3 END CAP Z WITH HAMMER TAPS 3 END CAP 45X45 VA 4 ANGLE 25 GD-Z 4 ANGLE 45X90 GD-Z 5 ANGLE 90 GD-Z 5 HINGE 19 S 6

More information

Installation Instruction

Installation Instruction Tools Needed for Assembly Stud finder (for wood stud wall) Pencil Mark Electric drill Wood Stud Wall Installation Step 1. Locate the Wood Studs Installation Instruction Drill bit (for wood stud wall) Masonry

More information

Model PLM5113N PETROL LAWN MOWER

Model PLM5113N PETROL LAWN MOWER Strana 1 / 2 Strana 2 / 2 Strana 1 / 4 001 671006065 "BLADE TIGHTEN BOLT 3/8""24" 1 002 671010730 LID SHAPE WASHER 1 003 DA00000973 BLADE 510MM 1 004 671015252 BLADE SUPPORT 1 005 DA00000535 FLAT KEY 1

More information

Assembly Instructions

Assembly Instructions Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt

More information

Motorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions

Motorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions Motorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions Tools Needed Drill 3/8 Metal Drill Bit ¼ Masonry Drill Bit Measuring Tape Pencil 4 Level Phillips

More information

ABM International, Inc. Navigator Assembly Manual

ABM International, Inc. Navigator Assembly Manual ABM International, Inc. 1 1.0: Parts List Tablet (Qty. 1) Tablet mount (Qty. 1) NOTE: Mount may appear and operate different then image below Control Box (Qty. 1) Motor Power Supply (Qty. 1) 2 X-axis motor

More information

NOTE: Top section pole (Q) is packed INSIDE bottom section pole (S)

NOTE: Top section pole (Q) is packed INSIDE bottom section pole (S) Form 0905-0 Instructions and Parts List TM- Mini Castle (modified) MARTIN SAFETY SYSTEM NOTES: () A complete system is packed in two boxes post box and house box. House box contains hardware for both post

More information

Downtown Rack. Custom logo option available

Downtown Rack. Custom logo option available Custom logo option available Downtown Rack The Downtown Rack uses thick, square-tube construction that can t be cut with a pipe cutter. The extended width of the Downtown Rack makes for easy bike parking

More information

THANK YOU FOR PURCHASING FROM HERITAGE PATIOS

THANK YOU FOR PURCHASING FROM HERITAGE PATIOS Installation Guide THANK YOU FOR PURCHASING FROM HERITAGE PATIOS Your purchase is engineered by nearly a half century of commercial and residential product design proudly manufactured in the USA from responsibly

More information

Installation Instructions

Installation Instructions Supafold Slide Aside System Three Fold Room Divider Installation Instructions Distinctive Doors Ltd Supafold Slide Aside Internal Folding System IMPORTANT: Before proceeding with the installation, and

More information

Ford Pick Up Rear leaf Spring Kit Installation Instructions

Ford Pick Up Rear leaf Spring Kit Installation Instructions 1948-1956 Ford Pick Up Rear leaf Spring Kit Installation Instructions 1-800-984-6259 www.totalcostinvolved.com Parts 48 inch leaf (2) springs (4) U-bolts 3/8-24 x l 1/4bolts (16) & nuts (2) 1/2-20 x 4

More information

BIFOLD FUTON FRAME TRINITY ARM. Seat Rails and Slats x 1. *Note: Use 4pc of 100mm Bolts and 4pc of 60mm Bolts to attach the arms to the Stretchers.

BIFOLD FUTON FRAME TRINITY ARM. Seat Rails and Slats x 1. *Note: Use 4pc of 100mm Bolts and 4pc of 60mm Bolts to attach the arms to the Stretchers. 1A Parts in this box. 2pc with extra holes 2pc with extra holes & plastic stoppers Arms x 2 Back Rails and Slats x 1 Full Size: Slat Supports x 6 3pc are longer for the Back deck Back Side Rails x 2 Seat

More information

LCD LIFT Flat Panel Display System Installation Manual. Table of Contents

LCD LIFT Flat Panel Display System Installation Manual. Table of Contents LCD LIFT Flat Panel Display System Installation Manual Table of Contents Page Installation Overview... 2 Trim Ring Installation... 3 LCD Lift Installation....4 Actuator Switch Installation.5 Top Plate

More information

ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS GARDEN SHED 6X5ft B/C 9400988362649 GARDEN SHED 6X7ft B/C 9400988362656 GARDEN SHED 6X9ft B/C 9400988362663 GARDEN SHED 6X1 B/C 9400988362670 111 ft ASSEMBLY INSTRUCTIONS Product specifications may change

More information

Assembly Instructions

Assembly Instructions 18' W x 10' H or 12' H Peak Style Frame Assembly Assembly Instructions Before you start: 2+ individuals recommended for assembly, approximate time 3 hours. Recommended tools: Power Drill, Safety Glasses,

More information

Swerve Rack CUSTOM RACKS AVAILABLE

Swerve Rack CUSTOM RACKS AVAILABLE CUSTOM RACKS AVAILABLE Swerve Rack The design of the Swerve mirrors the bike frame, thus providing superior bike support while making it easy to secure both the bike frame and wheel with a standard u-lock.

More information

Spring Loaded SCREEN-PRO. All Season Roll-Up Doors IN-JAMB MOUNTING METHOD INSTALLATION INSTRUCTIONS READ THIS FIRST

Spring Loaded SCREEN-PRO. All Season Roll-Up Doors IN-JAMB MOUNTING METHOD INSTALLATION INSTRUCTIONS READ THIS FIRST Spring Loaded SCREEN-PRO All Season Roll-Up Doors IN-JAMB MOUNTING METHOD INSTALLATION INSTRUCTIONS READ THIS FIRST Carefully examine the crate(s) for damage before opening. If the carton is damaged, immediately

More information

TOOLS REQUIRED FOR ASSEMBLY. Rubber Mallet or Plastic Tip Hammer PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER.

TOOLS REQUIRED FOR ASSEMBLY. Rubber Mallet or Plastic Tip Hammer PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER. TOOLS REQUIRED FOR ASSEMBLY Rubber Mallet or Plastic Tip Hammer Top Cover Support PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER Back Stop Divider Closed 'L' Upright Slotted Reinforcement Support

More information

Code Product Qty 1 Top Vertex 3 2 Hot End Housing 1 3 Bottom Vertex 3 4 Print Platform Lock 3 5 End Stop Holder 3 6 Filament Feeder Motor Bracket 1 7

Code Product Qty 1 Top Vertex 3 2 Hot End Housing 1 3 Bottom Vertex 3 4 Print Platform Lock 3 5 End Stop Holder 3 6 Filament Feeder Motor Bracket 1 7 List of Parts Code Product Qty 1 680mm Extrusion 3 2 Power Supply 1 3 240mm Extrusion 9 4 42mm Nema 17 Stepper Motor 3 5 Slider-Hotend Connecting Rod 6 6 48mm Nema 17 Stepper Motor 1 7 Linear Rail with

More information

Greenhouse Assembly Instructions

Greenhouse Assembly Instructions Greenhouse Assembly Instructions Our Help Line provides support and advice to customers of Summer Garden Buildings after ordering. For advice before you buy you can phone us free 7 days a week on 0800

More information

W6 series greenhouse

W6 series greenhouse W series greenhouse ssembly instructions Model W0 Model W07 Model W0 Model W Model W Walk-in Greenhouse Statement Dear Customer! May we congratulate you on your new Greenhouse. We feel sure that by following

More information

3.2.3 Rear Door Window and Quarter Window Carrier Assembly

3.2.3 Rear Door Window and Quarter Window Carrier Assembly Tighten all bolts. Tighten bolts marked -1- and -2- in specified sequence. Tightening torque: 8 Nm Remaining bolts can be tightened in any sequence. Insert door window -3- through window recess without

More information

NEW. Perfect Fit Roller Blind System Measuring, assembly & fitting instructions

NEW. Perfect Fit Roller Blind System Measuring, assembly & fitting instructions NEW Perfect Fit Roller Blind System Measuring, assembly & fitting instructions Perfect Fit Roller Blind System Measuring, assembly & fitting instructions Clearance & seals Seal Check clearance around the

More information

Hubble GOTO Installation Instruction (1.3, 04/30/2014)

Hubble GOTO Installation Instruction (1.3, 04/30/2014) Hubble GOTO Installation Instruction (1.3, 04/30/2014) 1. Preparation... 1 1.1 Tools required... 1 1.2 AZ GOTO Drive Parts List...1 1.3 ALT GOTO Drive Parts List... 1 2. The Azimuth motor drive installation...2

More information

Sectional Door Installation Instructions

Sectional Door Installation Instructions Sectional Door Installation Instructions 1. Check opening height and door size. a. 25-30mm overlap on each side and >10mm at top. b. At least 150mm side room required 2. Check headroom clearance, standard

More information

Installation Instructions - Model V4JSD 1

Installation Instructions - Model V4JSD 1 Installation Instructions - Model V4JSD 1 Support Assemblies: Parts list: (Note see enclosed cut sheet for quantities and dimensional information) A vertical structural member (1 ½ x 1 ½ modular frame)

More information

CURVED ROOF ASSEMBLY INSTRUCTIONS ATTACHED VERANDAH. Your supplementary guide to building an ATTACHED CURVED ROOF VERANDAH or PATIO BEFORE YOU START

CURVED ROOF ASSEMBLY INSTRUCTIONS ATTACHED VERANDAH. Your supplementary guide to building an ATTACHED CURVED ROOF VERANDAH or PATIO BEFORE YOU START ROOF ATTACHED VERANDAH ASSEMBLY INSTRUCTIONS Your supplementary guide to building an ATTACHED ROOF VERANDAH or PATIO This set of instructions should be used in conjunction with the Stratco instruction

More information

CRP700 Benchtop Basic CNC Machine Assembly Instructions. Updated 9/11/2014 SHEET 1 of 25

CRP700 Benchtop Basic CNC Machine Assembly Instructions. Updated 9/11/2014 SHEET 1 of 25 CRP700 Benchtop Basic CNC Machine Assembly Instructions Updated 9//0 SHEET of NOTE: This piece of extrusion is mounted wide side up Quick Tip: Lay extrusion on table as shown for easy assembly BASE ASSEMBLY:.

More information

Roll In W/L Dock PAGE 1

Roll In W/L Dock PAGE 1 Roll In W/L Dock PAGE 1 1 2 3/8 X 1 CARRIAGE BOLT SS 3/8 FLANGE NUT BRASS 3 4 1/2-13 X 1.25 SQ BOLT SS 1/2 SQ NUT BRASS 5 3/8-16 X 2.5" BOLT SS PAGE 2 6 7 BRACE BRKT SINGLE AXLE TUBE 8 9 3" AXLE WASHER

More information

The Phoenix. Professional Quilting Frame. Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.

The Phoenix. Professional Quilting Frame. Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2. The Phoenix Professional Quilting Frame Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.1 1 The Phoenix Professional Quilting Frame Parts List Box 1...3 Box

More information

EDGE2 DUAL MONITOR ARM

EDGE2 DUAL MONITOR ARM EDGE2 DUAL MONITOR ARM EDGE2 Rev A 2/17 Model EDGE2-SLV Model EDGE2-BLK Model EDGE2-WHT ASSEMBLY AND ADJUSTMENT EDGE2 DUAL MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning

More information

Install Instructions. NewAge Steel Welded Tall Locker

Install Instructions. NewAge Steel Welded Tall Locker Kit Contains Full Width Adjustable Steel Shelves (4) Height-Adjustable Steel Leveling Legs (4) Aluminum Door Trim (2) 2.5 x ¼ Cabinet Mounting Lag Bolts (4) Large Zinc Plated Mounting Washers (4) 5/8 x

More information

Parts list continues on Page 2 HOUSE PARTS PACKED IN HOUSE BOX PARTS IN SMALL PLASTIC BAG (HARDWARE) POST PARTS PACKED IN THIS BOX (LARGE PLASTIC BAG)

Parts list continues on Page 2 HOUSE PARTS PACKED IN HOUSE BOX PARTS IN SMALL PLASTIC BAG (HARDWARE) POST PARTS PACKED IN THIS BOX (LARGE PLASTIC BAG) Form 05-07 Instructions and Parts List MSS- Martin Safety System NOTES: () A complete system is packed in two boxes post box and house box. House box contains hardware for both post and house assembly.

More information

This manual will aid in the assembly of the FireBall V90 and FireBall X90. The assembly of both machines will be identical, unless specified.

This manual will aid in the assembly of the FireBall V90 and FireBall X90. The assembly of both machines will be identical, unless specified. This manual will aid in the assembly of the FireBall V90 and FireBall X90. The assembly of both machines will be identical, unless specified. Step #1 Lay all parts out to verify quantities. (2) 2 x 25-1/4

More information

Lange Crank Hoist-a-top Assembly Instructions

Lange Crank Hoist-a-top Assembly Instructions Lange Crank Hoist-a-top Assembly Instructions Installation Time: 1-4 Hours depending on skill level Tools Required: Cordless Drill Level Stud Finder Ratcheting wrench 9/16 socket or wrench 11/16 socket

More information

Assembly Instructions 10 X 10 Aluminum Frame Building

Assembly Instructions 10 X 10 Aluminum Frame Building Assembly Instructions 10 X 10 Aluminum Frame Building 27 97 9 8 47 36 74 52 10 10 X 10 Square Building W/ Dome Includes: The Steel Entry Door with a Dead Bolt Lock assembly and Aluminum Door Frame. Metal

More information

OWNERS MANUAL MODEL F660 HIP SLED

OWNERS MANUAL MODEL F660 HIP SLED OWNERS MANUAL MODEL F HIP SLED QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts, we will guarantee your complete

More information

BY ALIEN TECHNOLOGIES CORP

BY ALIEN TECHNOLOGIES CORP BY ALIEN TECHNOLOGIES CORP Assembly Instructions TopLift Pros YOU MAY ALSO REVIEW OUR ASSEMBLY VIDEO, PLAY AND PAUSE AT YOUR CONVENIENCE. JUST VISIT US AT WWW.TOPLIFTPROS.COM AND GO TO Customer Support

More information

ASSEMBLY AND ADJUSTMENT

ASSEMBLY AND ADJUSTMENT EDGE MONITOR ARM EDGE Rev A 2/17 Model EDGE-SLV Model EDGE-BLK Model EDGE-WHT ASSEMBLY AND ADJUSTMENT EDGE MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and

More information

S H E D A S S E M B L Y I N S T R U C T I O N S

S H E D A S S E M B L Y I N S T R U C T I O N S T I T A N R A N G E S H E D A S S E M B L Y I N S T R U C T I O N S 8 X 10 ft Approx = 2550 x 3140 cm COMPONENT LIST Component illustrations are given as a visual guide only and are not in proportion PART

More information

Kossel Rev B Build Guide V1.0

Kossel Rev B Build Guide V1.0 Kossel Rev B Build Guide V1.0 1 Table of Contents: Step 1: BASE ASSEMBLY Gathering parts: Building the Corners and Base: Step 2: UPPER ASSEMBLY Building Upper: Step 3: VERTICAL RAIL INSTALLATION Building

More information

Installation Instructions for Vista Air Vertically Folding Walls

Installation Instructions for Vista Air Vertically Folding Walls Installation Instructions for Vista Air Vertically Folding Walls Use these instructions in conjunction with your shop drawings to see the specifics that are particular to the model you are installing.

More information

TERRACE / TERRACE CONCEPT Retractable Classic Roof / Double Rail System Step by Step Assembly Instructions

TERRACE / TERRACE CONCEPT Retractable Classic Roof / Double Rail System Step by Step Assembly Instructions TERRACE / TERRACE CONCEPT Retractable Classic Roof / Double Rail System Step by Step Assembly Instructions Before You Begin These installation instructions will lead you through the process of installing

More information

Installation manual. Roller door RV55 - RV77

Installation manual. Roller door RV55 - RV77 Installation manual Roller door RV55 - RV77 Installation manual Roller door Content Package 1 1. Armor 2. Cap with axle 3. Guides 4. Suspension springs 5. Covers 6. Control a. Electrical: switch + plug

More information

BARLOW TYRIE quality since Ref: x 3m - 12 x 10 Pavilion with Cabrio Folding Roof Step by Step Assembly Instructions

BARLOW TYRIE quality since Ref: x 3m - 12 x 10 Pavilion with Cabrio Folding Roof Step by Step Assembly Instructions Pavilions 3.66 x 4.5m - Step 12 x by 15 Step Pavilion Assembly Shelter Instructions with Double Rail Beams Ref: 9011215 3.66 x 3m - 12 x 10 Pavilion with Cabrio Folding Roof Step by Step Assembly Instructions

More information

Clamping devices 521

Clamping devices 521 Clamping devices 521 522 Product overview Clamping devices Adjustable straps K0001 Hook clamps K0012 Goose-neck straps with long slot K0002 Page 526 Hook Clamps with collar K0013 Page 535 Equipped clamps

More information

Thanks for shopping with Improvements! 8 ft. Retractable Window Awning Item # (Fits windows/doors from 73 to 96 wide)

Thanks for shopping with Improvements! 8 ft. Retractable Window Awning Item # (Fits windows/doors from 73 to 96 wide) Thanks for shopping with Improvements! 8 ft. Retractable Window Awning Item #511412 (Fits windows/doors from 73 to 96 wide) Note: Read these instructions carefully before assembling. Find a clean, smooth

More information