K11.11 ORCA K11 DOORS

Transcription

1 K11 DOORS K Waregemstraat Zulte - Belgium - T F commercial@sobinco.com -

2 CONTENTS 1. General...K Description and advantages K Technical characteristics K Multipoint lock with standard latch bolt... K Turning and replacing the latch bolt... K Other latch bolts... K Short (K) and long (L) multipoint locks... K Short keeps... K With U-shaped faceplate K With flat faceplate K Keeps in zinc alloy K Long keeps...k With U-shaped faceplate K With flat faceplate K Shorter (K) and longer (L) version K Keeps with positioning piece...k Cases in synthetic material for flat keeps...k Electric door opener...k General characteristics K Installation on faceplate K Order codes K Types and function K Section preparations... K Locks K Keeps without electric strike K Keeps with electric strike K K

3 1. General 1.1. Description and advantages The multipoint lock is provided with top and bottom lock with an upward hook bolt and 2 security pins so that your doors are more secure against forced entry. Maximum reliability by means of: an improved latch bolt mechanism an improved handle mechanism not disengageable gear wheels: that s why the lock can not be forced during the working activities on the building site. The 3 hook bolts are pivoting, rather than sliding. They are therefore longer than conventional bolts, so there is the same proportion of the dead bolt within the lockcase as is engaged into the frame, making it extremely difficult for burglars to force entry by means of a crowbar. The hook bolts ensure security in horizontal direction, the pins in vertical direction. The upward hook bolts also serve as anti-lift security. The lock has special tapered top and bottom dead bolts which pull the vent section against the frame when locking the door, to provide an effective weather seal. Also a slightly deformed door (for example due to extreme weather conditions) can be closed without having to force the key. Centre lock Two holes above and below the handle opening allow the door handles to be screwed to each other through the lock, so there are no screws visible from the outside. The lock can be used left hand and right hand simply by turning the latch bolt. The latch bolt can be operated by the door handle as well as by the key. The lock is supplied with the standard latch bolt. The latch bolt is easily replaceable after installation with an easy operation. This is a very big advantage as you have to keep only 1 lock in stock. The other latch bolt types can be ordered separately. Locking and unlocking by a single turn of 360 with the cylinder key. Small turn moment when operating the latch bolt and when locking and unlocking the dead bolts. The vertical clearance (4 mm above and 6 mm below) between dead bolts and lock keeps should be sufficient in order to avoid the following problems: dropping of the door wrong vertical installation of the keep and/or lock K

4 1.2. Technical characteristics The lock is available in 3 lengths: Short version (K): 1895 mm Standard version: 2170 mm Long version (L): 2470 mm Vent height: With short lock: mm With standard lock: mm With long lock: mm Available in 3 backsets: 30 mm 35 mm 40 mm Faceplates: Flat faceplate: 16 mm, 20 mm and 24 mm U-shaped faceplate: 22x6.5 mm, 22x8,5 mm, 24x5 mm and 24x6.5 mm Very narrow lock: lockcase width = 15.5 mm. Top and bottom lock The latch bolt is available in 5 different versions: standard latch bolt extended latch bolt narrow latch bolt roller bolt cover plate (lock with only dead bolt) Note: we recommend to use an extended latch bolt when the distance between faceplate and keep is 6 mm or more, especially when electric strikes are used. The lock is entirely made of non-corroding materials: faceplate: stainless steel AISI 304 (austenitic) lockcases: zinc alloy, black passivated latch bolt: zinc alloy nickel plated dead bolts: zinc alloy nickel plated pins: stainless steel AISI 303 (austenitic) The locks have been tested by SKG in the Netherlands. Two stars are awarded to the locks in accordance with the star rating indicated in the KOMO certificate of SKG. The locks are tested in accordance with the European standard EN 12209:2003/AC:2005 and obtained the following classification code: Category of use Durability Door mass Fire resistance Safety Corrosion resistance Security Door application Type of key operation Type of spindle Key identification 3 X G 2 B A 2 0 K

5 2. Multipoint lock with standard latch bolt Vent height with standard lock: mm. Flat faceplate Order code A (mm) B (mm) C (mm) U-shaped faceplate Order code A (mm) B (mm) C (mm) D (mm) U U U U U U U U U U U U Indication line The indication line serves as reference point for the lock position in relation to the keep position. K

6 3. Turning and replacing the latch bolt Turning the latch bolt Changing the latch bolt Left hand and right hand lock. Put the dead bolt (B) in locked position. Pull the latch bolt (A) forwards with a pair of pliers or screwdriver (only for standard latch bolt) and turn 180. Move the latch bolt backwards. Put the dead bolt (B) in locked position. Pull the latch bolt (A) forwards with a pair of pliers or screwdriver (only for standard latch bolt) and turn 90. Remove the latch bolt from the lock. Position the new latch bolt horizontally. Turn the latch bolt 90 to move the latch bolt backwards. 4. Other latch bolts Cover plate for lock Narrow latch bolt Extended latch bolt with only dead bolt Set n (1 piece) Set n G80001 (20 pieces) Set n (1 piece) Set n G80002 (20 pieces) (When distance between faceplate and keep is 6 mm or more) Set n (1 piece) Set n G80004 (20 pieces) K

7 Roller bolts Set Set code 1 piece Set code 20 pieces Backset G mm G mm G mm Installation: 1) Insert spring and roller bolt 2) Turn roller bolt 90 3) Turn in the adjustment screw 4) Adjustment Order information The latch bolt sets contain: the latch bolt the installation instructions The roller bolt sets contain: the roller bolt the spring with length in accordance with the backset the adjustment screw with length in accordance with the backset the installation instructions When you require a lock with one of these latch or roller bolts, then you order a lock with standard latch bolt (see page K ) in combination with the required latch or roller bolt set. The advantage is that you don t have to take all the lock types in stock. Order example: lock with flat faceplate 20 mm and backset 35 mm with roller latch: Lock n Roller bolt set n K

8 5. Short (K) and long (L) multipoint locks Short lock Long lock The locks with flat as well as U-shaped faceplate are available in a shorter or longer version: the distance between the centre lock and the top lock is smaller or bigger than in case of the standard lock. K-version: Top lock is 275 mm lower compared to the standard lock. 1 fixing hole less compared to the standard version. L-version: Top lock is 400 mm higher compared to the standard lock. 1 fixing hole more compared to the standard version. Order codes: Short: (U)..K-.. Long: (U)..L-.. Vent height: With short lock: mm With long lock: mm (-275 mm) (+400 mm) K

9 6. Short keeps 6.1. With U-shaped faceplate or Right hand Left hand The U-shaped faceplate is 22 mm or 24 mm wide and 5.5 mm, 8.5 mm or 11 mm (only 22 mm) high. The keeps are provided with a stainless steel faceplate in AISI 304. The top and bottom keep is provided with a zinc alloy case. The encased keeps give a neat appearance and keeps the frame section free from dirt. The top and bottom keeps are horizontally adjustable by means of eccentric rollers which move the zinc alloy cases. The adjustment range is +/-1.5 mm. The centre keep is provided with a latch plate in zinc alloy for the latch bolt opening. This latch plate can be removed to use the keep in combination with an electric door closer: see page K This way, the same keeps can be used. The middle keeps n U22R and -U22L are also available with positioning piece: see page K The keeps have been tested by SKG in the Netherlands. Two stars are awarded to the keeps in accordance with the stars indication with relation to the KOMO certificate of SKG. The keeps are also provided with an indication line to check the keep position in relation to the lock position. or Faceplate height E 5.5 mm 8.5 mm Centre right Order code Centre left Top and bottom U22R U22L U U24R U24L U U22R U22L U U24R U24L U24 11 mm U22R U22L U22 Indication line Profile preparations: see page K K

10 6.2. With flat faceplate The faceplates are 22 mm wide and 2.5 mm high. The faceplate is in stainless steel AISI 304. The keeps are horizontally adjustable by means of eccentric rollers. Adjustment range: +/-2 mm. The centre keep n R (L) is provided with a latch plate for the latch bolt opening. This latch plate can be removed to use the keep in combination with an electric door closer: see page K This way, the same keeps can be used. The keeps have been tested by SKG in the Netherlands. Two stars are awarded to the keeps in accordance with the stars indication with relation to the KOMO certificate of SKG. Profile preparations: see page K The indication line serves as reference point for the keep position in relation to the lock position. Indication line Order code Type Centre Top/bottom Standard With latch plate R or L Without latch plate With latch plate Right hand Left hand K

11 6.3. Keeps in zinc alloy The keeps are horizontally adjustable by means of serrated plates. The adjustment range is +/-2,4 mm. The keeps are encased which gives a neat appearance and keeps the frame section free from dirt. Profile preparations: see page K Finish: keeps in zinc alloy, black passivated. Top and bottom keep Order code G (mm) H (mm) The indication line serves as reference point for the keep position in relation to the lock position. Indication line Order code Middle keep G (mm) H (mm) K

12 7. Long keeps 7.1. With U-shaped faceplate General: see page K Same characteristics as the separate zinc alloy keeps with stainless steel U-faceplate. The keeps n U22R and -U22L are also available with positioning piece: see page K The top and bottom keeps are horizontally adjustable by means of eccentric rollers which move the zinc alloy cases. The adjustment range is +/-1.5 mm. The keeps have been tested by SKG in the Netherlands. Two stars are awarded to the keeps in accordance with the stars indication with relation to the KOMO certificate of SKG. or Faceplate height E 5.5 mm 8.5 mm Right hand Order code Left hand U22R U22L U24R U24L U22R U22L U24R U24L 11 mm U22R U22L or Indication line The indication line serves as reference point for the keep position in relation to the lock position. Left hand = illustrated Right hand = opposite view K

13 7.2. With flat faceplate Same characteristics as the separate stainless steel keeps with flat faceplate. The keep n R (L) is provided with a latch plate for the latch bolt opening. This latch plate can be removed to use the keep in combination with an electric door closer: see page K This way, the same keeps can be used. Type Order code Standard With latch plate R or L The keeps have been tested by SKG in the Netherlands. Two stars are awarded to the keeps in accordance with the stars indication with relation to the KOMO certificate of SKG. Adjustment range Indication line The indication line serves as reference point for the keep position in relation to the lock position. Left hand = illustrated Right hand = opposite view K

14 7.3. Shorter (K) and longer (L) version With U-shaped faceplate With flat faceplate Short Long Short Long All keeps have been tested by SKG in the Netherlands. Two stars are awarded to the keeps in accordance with the stars indication with relation to the KOMO certificate of SKG. Both long keeps with flat faceplate as well as with U-shaped faceplate, are available in a shorter or longer version. In case of the L version there s 1 additional fixing hole. Order code Faceplate height E Short Long 5.5 mm U22R or L U22R or L U24R or L U24R or L 8.5 mm U22R or L U22R or L U24R or L U24R or L 11 mm U22R or L U22R or L Order code Type Short Long Standard With latch plate R or L R or L K

15 8. Keeps with positioning piece Positioning piece For rebated doors provided with a eurogroove with frame groove 14/18 mm, the keeps in the middle can be provided with a positioning piece. Advantages: Better positioning on the frame groove More solid fixing Reinforcement of the keep Securing the latch plate clamping nuts The positioning piece is not separately available and is supplied with the U-shaped keeps with faceplate 5,5x22 mm. Order codes keeps: Short keep Order code Description Right hand Left hand Long keep standard version Long keep shorter version Long keep longer version U22R U22L U22R U22L U22R U22L U22R U22L K

16 9. Cases in synthetic material for flat keeps General Cases in synthetic material which are mounted in the profile cut-out. These cases are only possible for profiles with frame groove 14/18 mm. To apply in combination with the short version as well as with the long version of the flat keeps. The case gives a neat appearance and keeps the frame section free from dirt. Centre n Top and bottom n Installation Hook in the upper side of the case behind the profile wall. Slide the case and position together with the keep. Fix the keep. K

17 10. Electric door opener General characteristics Small electric strike incorporating a spacesaving locking flap, especially developed for installation in aluminium doors. The flap rotates back within the keep when operated. Big advantage: the cut-out is much smaller making the installation aesthetically pleasing. Break-in resistance of strike: 3750 N. Width adjustment of the locking flap: 3 mm. Current consumption: Alternating current (AC): 250 ma at 12V Direct current (DC): 280 ma at 12V The electric strikes are non-handed. Mechanical release Reset button Electrical (type 788) connection Release button Electrical connection Reset button Quick and simple electrical connection. Adjustment range The reset button is only possible for type 128 where the strike is held in the release position until the door has been opened. This button resets the electric strike when the door opens. The release button (type 788) allows to suspend temporarily the automatic locking upon closing the door. Only available for type 118 and 128. K

18 10.2. Installation on faceplate For both short as long keeps. In order to be able to use an electric strike, a keep with latch plate must be used. Method: Remove the latch plate. Mount and fix the electric strike. Keeps with U-faceplate Keeps with flat faceplate Order codes The following electric strikes are available: Order code Voltage Note V AC/DC E 10-24V AC/DC With release button V AC/DC E 10-24V AC/DC With release button V DC V DC For more information about the types: see next page. K

19 10.4. Types and function Type 118 The door is only unlocked when you push a button. After releasing the button the door is locked again. This type works on 10-24V AC/DC and may be permanently connected to electrical supply up to 12V. Note: when the door is pushed open by the gaskets, the door can still be open after releasing the button. This can be solved by mounting a door closer on the door. Electric strike This type is available with release button (type 788). The release button allows to suspend temporarily the automatic locking upon closing the door. Door Operation Type 128 On releasing the electric strike, for example, from a button on an intercom system, the strike is held in the release position until the door has been opened. The electric strike resets when the door opens. This means there is no need to rush through the door. This type works on 10-24V AC/DC and may be permanently connected to electrical supply up to 12V. This type is available with release button (type 788). The release button allows to suspend temporarily the automatic locking upon closing the door. Electric strike Door Operation Type 138 This type works on 12V DC or 24V DC and may be permanently connected to electrical current. The electric strike is mainly used in combination with an alarm system. This means that for example in case of a power failure the door can be opened. Electric strike Door Operation K

20 11. Section preparations Locks Lock type A B C D E Standard Short (K) Long (L) Indication line The indication line serves as reference point for the lock position in relation to the keep position. Frame Vent R = Height reference K

21 11.2. Keeps without electric strike The preparations are applicable to: short keeps long keeps U-shaped faceplate flat faceplate The fixing holes G are not necessary in case of short (separate) keeps. Long keeps: see table. Keep type A B C D E F Standard Short (K) Long (L) Keeps with latch plate: Preparation for the latch bolt. Indication line The indication line serves as reference point for the keep position in relation to the lock position. Frame Vent R = Height reference K

22 11.3. Keeps with electric strike The preparations are applicable to: short keeps long keeps U-shaped faceplate flat faceplate with electric strike Faceplate D Flat 11 U5.5 x 22 mm 5.5 U8.5 x 22 mm 2.5 U11 x 22 mm 0 Section preparations for top and bottom keeps: see previous page. Long keeps: see previous page. The fixing holes G are not necessary in case of short (separate) keeps. The indication line serves as reference point for the keep position in relation to the lock position. Frame Vent Indication line R = Height reference K