BPF Toyota Tundra Mesh Installation Guide
|
|
- Barbra Miller
- 5 years ago
- Views:
Transcription
1 BPF Toyota Tundra Mesh Installation Guide Tools Required Philips Screw Driver Flat Head Screw Driver Dremel or Rotary Tool Hand Saw or Multi Max Adjustable Square Tape Measure Marker Zip Ties Drill 1/4 inch Drill Bit 1/8 Drill Bit Sandpaper or Sander ABS glue Yellow Plastic Welder or Solder Gun (Bondo will work as well) Black Paint (a textured paint will hide any blemishes) Masking tape 2+ Clamps It is a good idea to take your time and read the installation guide thoroughly before starting. Please ask us about any questions you have about the installation process, we are happy to assist you! Need help? Questions? Please, contact us at bpfabricating@gmail.com 1. Start by removing the hood latch bracket on the back of the grill. A Philips Screw Driver will be needed. Next, lay over the new hood latch bracket. Using masking tape lay it over both sides of the hood latch bracket on the OEM metal bar.
2 2. You can now remove the OEM bar leaving the masking tape on. Set the new hood latch bracket on top of OEM bar. Using a marker, mark out the holes. You can now drill out the mounting holes (using a punch will make things easier). 3. It is also a good time to drill out the mounting holes for the mesh. Drill out the holes like the photo below. They do not need an exact location, just close to the photo will work. About 6 inches apart. 4. We are almost done with the OEM bar. Lastly we need to slit a notch the ouster inside ends to allow for a little more clearance for the mesh. You can use a grinder or a Dremel tool for this. 5. You are now finished modifying the bar. It is a good idea to paint the bar so there is no bare metal showing. 6. Next using a flat head screw driver separate the inner and outer grill shrouds.
3 7. Cut out the center of the grill. Use a hand saw or a Multi Max or a Dremel. It is okay to leave some material on as you can clean up the edges after. 8. This is probably the most changing part of the install. With some patience and a steady hand, you can do it! Trim down the grill so that it will sit evenly. Before trimming, you need to draw on some measurements to adjust the grill depth. We recommend to measure twice on the areas that are cut. Make sure the grill is face down. All measurements will be taken on the inside perimeter of the grill. Measure all starting points at the inside of the front face (furthest point from you), towards the inside back end point (closer to you). At each point that requires measurement, make a mark with a marker/pen on the INSIDE of the grill. See the diagram below on the areas to measure. top 1 3/4 inch *Face Down 3/4 inch 3/4 inch Measure towards you. Inner backside of grill Inner finished front (Measuring starting point) bottom DRIVERS SIDE 1 7/8 inch PASSENGERS SIDE
4 Double check your work. It is very important to verify that all marks are accurate before the cutting process. Once all marks are correct you can use a ruler/meter stick to connect some of the marks 9. Using masking tape give yourself an edge to cut alongside as a guide. It may help to clean up the edges. Flow the edge of the cut line and use it to connect all the marks drawn. Take a step back and make sure everything looks correct and that you will have a flat edge. Now is the time to make any changes. 10. Using a Dremel with a cut off wheel, cut the edges of the grill following the masking tape line you made. 11. You are almost done. Now you need to fill those gaps on the sides using the material you cut off. Trim it so that it will sit flat or flush with the back of the grill. Once trimmed use the ABS cement and clamp in place. Work your way around the grill till all six gaps are filled. 12. Once dry you can use Bondo to fill in the rest of the gaps. Or you can plastic weld using a soldering gun by adding more plastic and melting the pieces together. Shown below is the plastic weld method.
5 13. Sand the insides of the grill and clean up the edges. Now is a good time to test fit the mesh and make sure it sits flat. If not, sand it down till it does. Once smooth you can get it ready to paint. 14. You can clean the grill with rubbing alcohol and paint it. We like to use a lightly textured paint. 15. Attach the new hood latch bracket to the OEM bar, using the supplied hardware. Attach the old hood latch bracket to the new one. 16. Put zap straps through the holes you drilled in the OEM bar. As its difficult ones it s installed. 17. Put the inner and outer grills shrouds together and reinstall the OEM bar. 18. Place the grill mesh on the back side of the grill. It is a tight fit with close tolerances so take the time to make sure it lines up correctly. Next you can zap strap the mesh down to the grill. Before tightening the zap straps make sure the grill is still lines up. 19. If you ordered lettering now is the time to install it using 3M doubles sided tape. Congratulations, your grill is now complete! Be sure to send us a photo of your work, we would love to share your photo. Direct message or Tag us on or it to us at bpfabricating.com. Thank You!
Applications: Section 1: Getting Started Tools Needed: BEFORE
Installation of KBD Body Kits Porsche GT 3 Look/Style 2 Piece Polyurethane Front Bumper & Lip Applications: Porsche 996: 1999-2001 Porsche Boxster 986: 1997-2004 Page 1 Tools Needed: Philips Head Screwdriver
More informationZROADZ Grille series - LED Installation Guide
ZROADZ Grille series - LED Installation Guide START HERE The ZROADZ Series Grilles comes into 2 different configurations. One style features the LED Light Bar mounting hidden on the backside, while the
More informationUPPER DOOR KIT P/N
UPPER DOOR KIT P/N 2879946 Application RZR XP4 1000 Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain these installation instructions
More informationYJ DeFenders. These installation instructions apply to the following Poison Spyder products:
INSTALLATION INSTRUCTIONS INST-13-02-070_A YJ DeFenders IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation. If
More informationPolaris General Doors #06016 Installation & Operations Manual Fits Polaris General
Polaris General Doors #06016 Installation & Operations Manual Fits Polaris General Before You Start: Please familiarize yourself with all the steps before beginning assembly. Compatibility Info: This Door
More informationGENERATION II FENDERS
INSTALLATION INSTRUCTIONS FOR 97-06 JEEP TJ GENERATION II FENDERS *Thank you for your purchase of our Generation II Fenders! We hope that you will love the new look and function of your Jeep with the addition
More informationInstallation for Full Size Polaris Ranger Crew Doors
Installation for Full Size Polaris Ranger Crew Doors Order of Installation: Heater Doors Wiper on to Windshield Windshield Top & Back Panel Note: Most of the steps in these instructions need to be repeated
More informationEntrance Cabinet Plans
Entrance Cabinet Plans www.andrewharriswoodwork.com Page 1 of 19 Introduction I have tried to ensure all steps are covered in these plans but if you find any errors in the plans or have a question then
More informationJeep. Flat Style Fender Flares Front Pair. Included in Hardware Kit:
Jeep Flat Style Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationIncluded in Hardware Kit. Jeep Cut-Out Fender Flare Set of 4 Set Part # Rev STEP 1 PRIOR TO INSTALLATION
Jeep Cut-Out Fender Flare Set of 4 Set Part #10926-07 Rev-01 09-11-12 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the flares according to these written instructions with the hardware
More informationRLP Mini Low Profile V Track Hardware sliding door hardware/ barn door track
Page 1 of 9 Installation Suggestions for: RLP Mini Low Profile V Track Hardware sliding door hardware/ barn door track Read these instructions to end before starting installation or ordering hardware.
More informationAll Terrain Flares 09+ Ford F150
Page 1/5 Components: 1. Front Flares (2) 2. Front Flare Inner Pieces (2) 3. Rear Flares (2) Tools required: - Utility knife - Electric Drill - 1/4 Drill Bit - #2 Phillips driver - Socket wrench Hardware
More informationINSTALLATION INSTRUCTIONS 3"/4 BENT END SIDEBARS FORD F-150 SUPERCREW PART # DZ /DZ
INSTALLATION INSTRUCTIONS 09-12 FORD F-150 SUPERCREW PART # DZ 372697/DZ 372699 PARTS LIST: 1 Driver/Left Sidebar 4 1/2 Lock Washers 1 Sidebar 4 12mm x 32mm OD x 3mm Flat Washers 1 Driver/Left Mounting
More informationJK Front Crusher Flares
INSTALLATION INSTRUCTIONS INST-17-03-030_A JK Front Crusher Flares IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation.
More informationPLEASE READ THIS NOTICE BEFORE BEGINNING ANY PHASE OF INSTALLATION!!!!
PLEASE READ THIS NOTICE BEFORE BEGINNING ANY PHASE OF INSTALLATION!!!! This kit is designed to be installed by someone with a fair amount of mechanical aptitude. However, if you are not comfortable making
More information2010+ Dodge Ram 2500/3500 Front Bumper Install Instructions
2010+ Dodge Ram 2500/3500 Front Bumper Install Instructions Warning! Read the instructions completely before beginning the installation. Before tightening bolts, drilling or cutting where required, check
More informationSE5a Instrument Board part 2 - rev 1.1
SE5a Instrument Board part 2 - rev 1.1 Fuel (Petrol) Valve This valve uses two circular name plates, eight brass screws, one black plastic base, copper wire and two black plastic risers. You can pick any
More informationFENDER FLARE INSTALLATION
Customer Support TM FENDER FLARE INSTALLATION TG-FF8C4108 IMPORTANT TYGER only approves the installation according to our instructions with the hardware provided. WARNING Failure to complete the installation
More informationBMW X5 OEM RUNNING BOARD PART#SBBW
INSTALLATION INSTRUCTIONS 2014-2016 BMW X5 OEM RUNNING BOARD PART#SBBW-146-74 QTY HARDWARE 1 Driver Side OEM Running Board 1 Passenger Side OEM Running Board 8 Rivet Pin 1 Page Step 1: Verify all parts
More informationJK Rear Crusher Flares
INSTALLATION INSTRUCTIONS INST-17-05-010_A JK Rear Crusher Flares IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation.
More informationPLEASE READ THIS NOTICE BEFORE BEGINNING ANY PHASE OF INSTALLATION!!!!
PLEASE READ THIS NOTICE BEFORE BEGINNING ANY PHASE OF INSTALLATION!!!! This kit is designed to be installed by someone with a fair amount of mechanical aptitude. However, if you are not comfortable making
More informationToyota Cut-Out TM Fender Flares Set of 4
Toyota Cut-Out TM Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationCut-Out Fender Flares Rear Pair. Jeep. Included in Hardware Kit:
Jeep Cut-Out Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationJeep. Cut-Out Fender Flares Set of 4. Included in Hardware Kit: Set Part # Rev-8 06/29/16 STEP 1 PRIOR TO INSTALLATION
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationRLP Flat Track Hardware sliding door hardware/ barn door track
Page 1 of 9 Installation Suggestions for: RLP Flat Track Hardware sliding door hardware/ barn door track Read these instructions to end before starting installation or ordering hardware. Reclaimed Lumber
More informationJK Crusher Corners. *Includes ONE of the Hardware Kits (not both)
INSTALLATION INSTRUCTIONS INST-18-05-020_A JK Crusher Corners IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation.
More informationASSEMBLY INSTRUCTIONS FOR MAR-K BEDSIDES AND GM FLUSH TAILGATE WITH HANDLE
ASSEMBLY INSTRUCTIONS FOR MAR-K BEDSIDES AND 41-53 GM FLUSH TAILGATE WITH HANDLE Build the box assembly according to the MAR-K assembly instructions. When installing the tailgate and latching mechanisms
More informationFlat Style Fender Flares Rear Pair. Jeep. Included in Hardware Kit:
Jeep Flat Style Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationJeep. Flat Style Fender Flares Set of 4. Included in Hardware Kit: STEP 1 PRIOR TO INSTALLATION. Set Part # Rev-3 1/11/2016
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationFlat Style Fender Flares Front Pair. Jeep. Included in Hardware Kit:
Jeep Flat Style Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationContinue gluing the remaining top parts ensuring the angled piece is glued well. Set aside and let dry. See photo below
Radiator rev 1.1 The SE5a s radiator is one of the most recognized radiators in WW1. It is one of the components that defines the SE5a. The original SE5a has seen multiple radiator designs used during
More informationAll Terrain Flares 2014 Chevy Silverado
Page 1/8 Components: 1. Front Flares (2) 2. Rear Flares (2) Tools required: - Utility knife - #2 Phillips driver - Socket wrench - 13 mm Socket - 6 mm Allen Wrench - T-15 Torx bit - Trim Removal Tool -
More informationPROJECT PLANS ROLLING LAUNDRY SORTER
R PROJECT PLANS ROLLING LAUNDRY SORTER Sorting laundry certainly doesn t rank high on anyone s list. So, anything that makes this task easier is welcome. If that functionality can be mixed with a bit of
More informationASSEMBLY & INSTALLATION GUIDE
ASSEMBLY & INSTALLATION GUIDE APPLICATION GM Truck (Full-size Trucks) PART # 74805-00A (Silver) 74805-0A(Black) INSTALLATION TIME Hour SKILL LEVEL 2 3 4 = Easy TOOLS REQUIRED Phillips screw driver Torx
More informationMallet Painting equipment Pop rivet gun
RotorWay International Page A Body Check, Paint, and Interior Liners Procedures covered in this section: Assemble body apart from airframe and check overall fit; remove tail boom; fit and install eyebrow
More informationSALEEN BODY KIT INSTALLATION MUSTANG
SALEEN BODY KIT INSTALLATION 1994-1998 MUSTANG PART# 10-8002-C14234A Saleen Performance, Inc. 1225 East Maple Rd. Troy, MI 48083 248-743-4800 www.saleen.com 2 IF YOU ARE NOT EXPERIENCED IN THE AREA OF
More information1/4 Rubber Spacer, 26 pcs. M5-.8 Machine Screw, 26 pcs 13. Female Wire Connector, 4 pcs
97-06 Jeep Wrangler TJ Set Part #10920-07 Rev-3 12-15-08 A) B) C) D) E) F) G) STEP 1 - PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with
More informationToyota Tacoma Extended Cab/Standard Cab Set Part # Rev
Toyota Tacoma Extended Cab/Standard Cab Set Part # 31919 Rev-7 06-23-10 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with the
More informationFlat Style Fender Flares Front Pair. Jeep. Included in Hardware Kit:
Jeep Flat Style Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationFig A. ADDICTIVE DESERT DESIGNS Preparation: Installation:
Preparation: Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. We recommend reading through the installation instructions in whole before performing
More informationInstallation Instructions
86-95 Suzuki Samurai LROR Sport Cage Front (SKU# SRC-SCF) Installation Instructions Front and Rear Cage Combined CAUTION: Safety glasses should be worn at all times when working with vehicles and related
More informationBushwacker Jeep Flat Style Fender Flares Front Pair
Bushwacker Jeep Flat Style Fender Flares Front Pair Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4 Hours Tools Required:
More informationMM Strut Tower Brace, Cobra (MMSTB-7)
The MM strut Tower Brace attaches to each strut tower and to the firewall. 3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com MM
More informationINSTALLATION GUIDE PREMIUM FRONT BUMPER. AEV30103AE Last Updated: 09/08/14 US PATENTS: D683281, D CHINESE PATENT: ZL
PREMIUM FRONT BUMPER US PATENTS: D683281, D697842 CHINESE PATENT: ZL 2012 3 0026081.4 AEV30103AE Last Updated: 09/08/14 INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION,
More informationSlide the stock rubber tank mount caps onto the ends of the CS-1 tank mount:
RYCA CS-1 BODY PARTS INSTALLATION GUIDE [The CS-1 installation guides should be used as supplements to the videos found on our Youtube Channel. There is no strict order to the build process, but it is
More information03-05 Accord 4Dr Installation Instructions. Table of Contents. Aggressive Lower Grille Pages 1-2 Upper Grille Pages 3-5 Subtle Lower Grille Pages 6-7
03-05 Accord 4Dr Installation Instructions Table of Contents Aggressive Lower Grille Pages 1-2 Upper Grille Pages 3-5 Subtle Lower Grille Pages 6-7 Aggressive Lower Grille Tools required: A flat blade
More information*Patent Pending. *Trademarked. Series II. Glass Conversion Kit. (888) One-Products (888)
*Patent Pending *Trademarked Series II Glass Conversion Kit www.onepieceproducts.com (888) One-Products (888) 663-7763 Installation Manual Full One Piece Door Glass Conversion Kit Series II 1967-1972 Chevy
More informationk 5356 PINE AVE FRESNO, CA USA TOLL FREE: 877.4X4.TOYS WORLDWIDE:
tacoma front shackle kit 110821-1-k kit contents 5356 PINE AVE FRESNO, CA 93727 USA TOLL FREE: 877.4X4.TOYS WORLDWIDE: 559.252.4950 WWW.TRAIL-GEAR.COM recommended tools Loctite Cutoff Wheel Welder Grinder
More informationIMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
IMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE 005-07 Cadillac STS Classic 3D Z, Classic Dual Weave, Classic Mesh & Classic Black Mesh Grilles B 7 HR 3 STS Classic 3D Z Grille Part
More informationLEXUS LS460/600h/L INSTALLATION MANUAL FRONT HALF SPOILER. USF40/41 UVF45/46 (2012y~) ATTENTION WALD. INTERNATIONAL ATTENTION
FRONT HALF SPOILER 1) Temporarily install WALD Front Spoiler to the body. Adjust the details of WALD Front Spoiler to fit the body by rasps or sandpapers. 2) Check the balance of the installation position
More informationFENDER FLARE INSTALLATION
TG-FF8T4178: Fit 2014-UP Toyota Tundra PRIOR TO INSTALLATION IMPORTANT Tyger only approves the installation according to our instructions with the hardware provided. WARNING Failure to complete the installation
More informationWanderlust Suitcase Vanity
Wanderlust Suitcase Vanity If you re like me, you re always up for an adventure. When I saw some examples of DIY reclaimed suitcases, paired with the exciting new Wanderlust embroidery design collection,
More informationMake a cupboard as a BCATS
National Certificate in Building, Construction, and Allied Trades Skills (BCATS) Make a cupboard as a BCATS project Unit Standard 25921 Level 2, Credit 6 Name: Contents Reference Page What you need to
More informationBullet Proof Anti-Stab Instructions
Bullet Proof Anti-Stab Instructions Kit Contains: 1 Solid Machined Aluminum Center Shaft w/ two press fit wheels 2 Solid Machined Aluminum Outer Shafts w/ press fit wheel 2 12mm x 100mm Flange Headed Bolts
More informationAfter the canopy hinge is square with the firewall and the nut plates are installed you can set up the hinge mounts. Start by clamping a 1/16 tongue
Written by: Sean Cole September 19, 2008 When fitting the stiffener use 3/32 clecos to hold it in place, it makes a smaller hole and is easier to work with. Only use the amount needed to hold the stiffener
More informationSTYLE BAR & TONNEAU COVER INSTALLATION
STYLE BAR & TONNEAU COVER INSTALLATION INSTALLATION MANUAL: 2005 to '09 Mustang P/N: 10-8002-C12071B Saleen Performance, Inc. 1225 East Maple Rd., MI 48083 800-888-8945 www.saleen.com 1 IF YOU ARE NOT
More informationTOOL LIST FOR TAILGATE HIDDEN LATCH & LINK ASSY FOR FORD FLARESIDE TRUCKS
TOOL LIST FOR TAILGATE HIDDEN LATCH & LINK ASSY FOR 53-87 FORD FLARESIDE TRUCKS Vise Grip Clamps C-clamps Sharpie Marker Ball Peen Hammer Center Punch 3/8 or 1/2 Drill 5/32, 7/32, 9/32, and 3/8 Drill Bits
More information53guy USMC Heavy Lift Inc.
NAXJA TITANIUM SPONSOR: Tom Woods Custom Drive Shafts NAXJA Forums -::- North American XJ Association > NAXJA's Technical Forums > FAQ; Frequently Asked Questions Front Fender Trim Write Up (Retaining
More informationInstalling your new Bevella Top. L Shaped Countertop with Joints No Finished Ends (Fits Between Four Walls)
Installing your new Bevella Top L Shaped Countertop with Joints No Finished Ends (Fits Between Four Walls) Bevella RTI Countertops are engineered and manufactured to the highest quality standards, built
More informationTrack Bumpers Wood or Plastic Your Choice
Track Bumpers Wood or Plastic Your Choice An assembly method is presented to build track bumpers for non-ballasted track such as Atlas O 2st Century, Ross Custom, Gargraves etc. Whether you decide to build
More informationMaking Simple Bookbinding Equipment
Tony Firman 20 1 2 19 Notes Tony Firman Tony Firman Bookbinding 18 3 : 2012 Tony Firman Bookbinding P.O. Box 507 Haslet, TX 76052 www.tonyfirmanbookbinding.com 4. When all the tapes have been pinned in
More informationA Day House. A View of One Way to Finish the Exterior of The Day House. Read these instructions all the way through before beginning this project.
A Day House A View of One Way to Finish the Exterior of The Day House Read these instructions all the way through before beginning this project. General Comments For the purposes of this project, the standard
More informationIncluded in Hardware Kit 2. FLAT STYLE FENDER FLARE. Jeep Wrangler YJ. Set Part # Rev STEP 1 PRIOR TO INSTALLATION
Jeep Wrangler YJ Set Part #10924-07 Rev-0 05-05-11 A) B) C) D) E) STEP 1 PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with the hardware
More informationU-bass Kit Assembly Instructions
U-bass Kit Assembly Instructions Compiled by playubass.com This guide is built from the instructions found here: http://kalabrand.com/ubass-kit/index.html Tools Needed 5/8 (16 mm) Wrench 7/16 (~11 mm)
More informationCUSTOM SHUTTERS IN-A-BOX
CUSTOM SHUTTERS IN-A-BOX SHUTTER ASSEMBLE INSTRUCTIONS & INSTALLATION INSTRUCTIONS 1. Inspect the contents of your package. Do not discard the shutter packaging box until you have started painting your
More information129 KITCHEN BASE CABINET 480
129 KITCHEN BASE CABINET 480 There are two sorts of kitchen cabinets: base cabinets, which sit on the floor, and wall cabinets. Base cabinets provide both storage space and work surfaces. They often house
More informationNISSAN NV200 CHEVY CITY EXPRESS WALL LINER KIT INSTALLATION INSTRUCTIONS
NISSAN NV200 CHEVY CITY EXPRESS WALL LINER KIT INSTALLATION INSTRUCTIONS NOTES: 1. Before commencing, remove all wall liners and D Rings already installed in the vehicle. 2. Consult layout PDF and compare
More informationINSTALLATION INSTRUCTIONS FOR & Chevy CUT OUT FLARE
40009 7/10/03 REV-A INSTALLATION INSTRUCTIONS FOR 40009 & 40010 Chevy CUT OUT FLARE TOOLS REQUIRED FOR INSTALLATION: Drill Motor Pop Rivet Gun Flat File Hair Dryer or Heat Gun Sawzall Jack and Jack Stands
More informationInstallation Instructions
TOYOTA 16K Industry Standard Rail Custom Mounting Kit #2748 Gross Trailer Weight (Maximum)...16,000 lbs. Vertical Load Weight (Max. Pin Weight)...4,000 lbs. SYSTEM TOW CAPACITY Please note, in order to
More informationIncluded in Hardware Kit 2. FLAT STYLE FENDER FLARE. Jeep Wrangler YJ Fronts. Set Part # Rev STEP 1 PRIOR TO INSTALLATION
Jeep Wrangler YJ Fronts Set Part #10067-07 Rev-0 05-05-11 A) B) C) D) E) STEP 1 PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with the hardware
More informationTools and Tips: ( 1 )
Tools and Tips: As you build instructions will show in my many picture manual how to assemble. You can use your own methods as you desire, my results are very good. A smooth, flat work surface is very
More informationJK FRONT FENDER FLARE INSTALLATION INSTRUCTIONS
JK FRONT FENDER FLARE INSTALLATION INSTRUCTIONS TOOLS NEEDED 3/16 Allen Wrench 1/2 Socket or wrench 10mm Socket Flat head screwdriver HARDWARE 5/16 x 3/4 button heads (14) 5/16 x 1 button heads (8) 5/16
More information* Drill and 3/32" drill bit: for drilling holes in the factory plastic upper for the screws to secure the brackets (factory upper installation only)
* Two slider windows (four sliders windows for the 4-door kit) * Four brackets to secure the windows to the upper door frames (8 brackets for the 4-door kit) * Weatherstrip to seal the windows to the half
More informationAssembly Instructions 10 X 10 Aluminum Frame Building
Assembly Instructions 10 X 10 Aluminum Frame Building 27 97 9 8 47 36 74 52 10 10 X 10 Square Building W/ Dome Includes: The Steel Entry Door with a Dead Bolt Lock assembly and Aluminum Door Frame. Metal
More informationFLEXITEEK INSTALLATION INSTRUCTIONS
an Advanced Plastic Fabrications Company 99 marcus Blvd., 631.244.3620 631.231.4466fax FLEXITEEK INSTALLATION INSTRUCTIONS Before you begin, take your new Flexiteek deck out of the shipping package and
More informationJeep. Flat Style Fender Flares Rear Pair. Included in Hardware Kit:
Jeep Flat Style Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationMetroboard Pulley Replacement Procedure
Metroboard Pulley Replacement Procedure 1) Remove the two transmission cover screws (1/8 allen driver). Then remove the transmission cover. Note there is a split lock washer and flat washer as well, so
More informationTUBULAR FRONT END KIT INSTALLATION INSTRUCTIONS MUSTANG
TUBULAR FRONT END KIT INSTALLATION INSTRUCTIONS 1979 2004 MUSTANG Pre-Installation Notes & Recommendations: Before disassembly, remove anything within the engine bay that can be removed; this will give
More informationBushwacker Jeep Flat Style Fender Flares Rear Pair (JK Wrangler 2dr)
Bushwacker Jeep Flat Style Fender Flares Rear Pair (JK Wrangler 2dr) Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4
More informationINSTALLATION INSTRUCTIONS PART#:17A045200MSS\17A045200MA MODULAR GRILL GUARD FOR FORD SUPER DUTY F250/F
INSTALLATION INSTRUCTIONS PART#:17A045200MSS\17A045200MA MODULAR GRILL GUARD FOR FORD SUPER DUTY F250/F350 08-09 1 guard, center section 1 brush guard, left side 1 brush guard, right side 1 wire guard
More informationSeascape Bungalow Assembly instructions. Laser Dollhouse Designs
Seascape Bungalow Assembly instructions Laser Dollhouse Designs NOTE: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and fit. This also
More informationCobra X Q Construction Tips Construction: Bel y pan
Cobra X Q Construction Tips : The white plastic in this kit is high impact styrene. It can be painted with most types of coatings if light coats are applied this is necessary due to the thickness of the
More information968 Side Cladding Rubber Beading Replacement
968 Side Cladding Rubber Beading Replacement A common and simple wear-oriented project for the 968 is the replacement of the rubber seals or beading on the lower side body cladding. These seals become
More informationPROJECT PLANS WOODEN GIFT BOX
PROJECT PLANS WOODEN GIFT BOX Make the gifts you give even more special by presenting them in this one-of-a-kind gift box. In fact, the box may be valued more than whatever it contains. The box is sized
More informationCLUB-SPORT ROLL BAR: Volkswagen Mk4 Golf
HPA Motorsports Inc. 604-888-7274 www.hpamotorsport.com CLUB-SPORT ROLL BAR: Volkswagen Mk4 Golf Congratulations on the purchase of your Club-Sport Roll Bar from HPA Motorsports! The engineering elements
More informationBig Oz. Rocket. User Guide V0313
Big Oz Rocket User Guide 59824 V0313 Materials Included The Big Oz Rocket Kit should include the following materials. If something is missing, contact Customer Service at 800-358-4983. 20-ounce plastic
More informationRugged Ridge Body Armor Guard Kit, 5 Pieces, Black (07-Current JK 4-door)
Rugged Ridge Body Armor Guard Kit, 5 Pieces, Black (07-Current JK 4-door) Installation Time: 60 Minutes Tools Required: Notes: Phillips head screwdriver 3/8 socket or Flat head screwdriver 1/2 socket 7
More informationIncluded in Hardware Kit: Pocket Style Extended Coverage Fender Flares Front Pair. Jeep
Jeep Pocket Style Extended Coverage Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided.
More informationPRO CYC PRO CYC, INC. SYSTEM SUPER 1.5QS
Assembly Instructions System Super 1.5QS Congratulations on your decision to use the world s most advanced and user-friendly cyclorama system. We have taken a great deal of care to create and ship your
More informationCompetition Engineering 8 Point Roll Bar (94-04 Mustang)
Competition Engineering 8 Point Roll Bar (94-04 Mustang) Required tools: Socket set / Hand tools Welder of choice Welding blankets Welding safety gear Heat gun Putty knife Bar notching tool Adjustable
More informationBird Feeder. Tool Requirements
Bird Feeder Written and constructed by Craig Tilley This wooden bird feeder will be an attractive addition to your garden. Its wide trays allow plenty of room for birds to come and have a snack, and the
More informationPre-Paint>Fuselage>Empennage>Fit elevator. Objectives of this task: Materials required: Prepare the horizontal stabiliser and the elevator
Pre-Paint>Fuselage>Empennage>Fit elevator Objectives of this task: To fit the elevator to the horizontal stabiliser, to fit the trim tabs to the elevator and the end caps to the elevator and the horizontal
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount For Chevrolet Silverado 1500HD & 2500 Kit 68162 This WARN Trans4mer system can be customized to give your Chevy Silverado a wide variety of
More informationRebuilding the Original Ford 8N Front Bumper
Rebuilding the Original Ford 8N Front Bumper by John Korschot - www.johnsoldiron.com February 2010 Almost everyone recognizes the original Ford front bumper. It's easy to spot as it drops towards the front
More informationPrecision Steel Car s 100 T Steel Coil Car
Precision Steel Car s 100 T Steel Coil Car Precision Steel Car www.precisionsteelcar.com info@precisionsteelcar.com Paul Vernon: (513) 571-5739 Revised 4/30/2009 Contents of Kit Main Tube Side Frame 2
More information1 ¼-inch Pocket Screws Brad Nailer or Hammer 1 ¼-inch Brad Nails Clamps
MATERIALS: TOOLS: (4) 2 x 6 x 8 Ft. Boards Tape Measure (2) 2 x 4 x 8 Ft. Boards Carpenter s Square (7) 1 x 4 x 8 Ft. Boards Pencil (2) 1 x 3 x 8 Ft. Boards Drill (1) Half Sheet of ¾-inch Thick Plywood
More informationOmarshauntedtrail.com. Obtained from. Merlin's Wall Sconce.
http://hauntershangout.com/home/wallsconce.asp Plaque Construction Merlin's Wall Sconce Warning: This project uses Electricity! Build at your own risk. Not for children to build. Ever been to a haunt and
More informationMINI Cooper Model 120SA Installation Instructions
MINI Cooper Model 120SA Installation Instructions Please read these instructions completely before beginning the installation. Test fit all components (amplifier, etc.) before mounting. These instructions
More informationFENDER FLARE INSTALLATION
Part#: TG-FF8G4158 FOR 2007-2013 GMC Sierra 1500 Pickup Truck (Exclude 69.3inch Short Bed Models) FENDER FLARE INSTALLATION Hardware Kit Included IMPORTANT TYGER only approves the installation according
More informationCUT OUT FLARES INSTALLATION INSTRUCTIONS FOR 20017, 20018, F100-F150 F250-F350 P.U. & BRONCO CUT OUTS
20017 04/22/03 REV-A CUT OUT FLARES INSTALLATION INSTRUCTIONS FOR 20017, 20018, F100-F150 F250-F350 P.U. & BRONCO CUT OUTS Tools Required for Installation: (A) 3/16 Drill Bit (B) Pop-Rivet Gun (C) Air
More information