CLUB-SPORT ROLL BAR: Volkswagen Mk4 Golf
|
|
- Dominick Marsh
- 6 years ago
- Views:
Transcription
1 HPA Motorsports Inc CLUB-SPORT ROLL BAR: Volkswagen Mk4 Golf Congratulations on the purchase of your Club-Sport Roll Bar from HPA Motorsports! The engineering elements used in HPA s custom built roll cages are now available for your high performance street use in the form of this bolt-in four point roll-bar. Offering increased on-track safety and added chassis rigidity, it features a removable harness bar and maintains full functionality of front and rear seats. Note to Racers: This product may not conform to the regulations of your local sanctioning body. Please refer to your rule book for clarification. Approximate Installation Time: 12 Hours Skill Level: Intermediate Requires precision measuring, cutting and finishing work. No welding required. This Installation Requires Two Persons 13mm Socket 17mm Socket 13mm Wrench 17mm Wrench 5mm Allen Key 10mm Allen Key Ratchet Extension Torque Wrench Pliers Paint Marker Center Punch Scribe or Pick TOOLS / SUPPLIES REQUIRED: Utility Knife Flashlight Magnetic Holding Tool Power Drill 1/8 Drill Bit 11/32 Drill Bit 3/16 Drill Bit 2-1/4 Hole Saw De-burring Tool Philips Head Screwdriver Contact Cement/Spray Glue Heat Gun (or hairdryer) Grease Torque Specs: The recommended torque specs for the hardware supplied with this are as follows: M8-25 ft-lbs M10-47 ft-lbs M12-83 ft-lbs
2 CLUB-SPORT ROLL BAR: Volkswagen Mk4 Golf PACKING LIST: While every effort has been made to ensure your Club-Sport Roll Bar has been shipped complete, please check contents of package thoroughly before beginning installation. (1) 1 x Main Loop (2) 4 x Bottom Pedestal Plates (3) 2 x Pedestal Hats (4) 1 x Left Pedestal (5) 1 x Right Pedestal (6) 1 x Harness Bar (7) 2 x Lateral Bars (8) 1 x Left Main Hoop Base (9) 1 x Right Main Hoop Base Hardware Package A: 6 x M12x30mm Socket Head Bolts Hardware Package B: 8 x M8x25mm Counter Sunk Socket Head Bolts 8 x 8mm nuts 8 x 8mm flat washers Hardware Package C: 6 x M10x30mm Socket Head Stud with pre-fitted nuts 6 x M10 Stover Nuts 6 x 10mm flat washers Hardware Package D: 16 x M8x30mm Hex Head Bolts 16 x M8 nuts 16 x 8mm Flat Washers 16 x 8mm Lock Washers Hardware Package E: 2 x M12x75mm Hex Head Bolts 4 x 12mm flat washers 2 x 12mm nuts 4 x concave spacers Additional Items: 2 x Paper Templates 1 length of Edge Trimmer 1 length of.023 Wire
3 Step 1: Prepare Cabin for Installation - Remove front passenger seat * - Remove rear seats * - Remove hatch trim rear panel * - Remove right and left rear side trays * - Remove right and left side speaker panels * - Remove right and left rear carpet panels, amplifier, amp bracket, and wiring on left side * - Remove right and left rear seatbelt retractors * - Remove right and left door sill trim panels * - Pull carpet forward, away from rear seat - Jack up rear of car and brace vehicle following standard safety practices and equipment - Remove rear wheels and wheel well liners Fig. 01 * Refer to standard VW removal procedures as outlined in the Bentley manual Step 2: Pre-Fit Roll Bar - Using hardware Package B, bolt pedestal hats to pedestals. Fig.01 - Place right and left pedestals in appropriate locations. Fig. 02, 03 - Place right and left main loop bases in appropriate locations. Fig.04, 05 - With end links facing rearward, slide main hoop into its bases and tip into position - Install hardware kit E finger tight into main loop bases - Install right and left lateral bars between main hoop and pedestals with hardware kit A; finger tight. - With roll bar in appropriate position, main hoop bases and pedestal flanges sitting flat; mark all mounting holes for pedestals and bases with a marker. Fig Disassemble and remove entire roll bar Fig. 02 Fig. 03 Fig. 04 Fig.05 Fig. 06
4 Step 3: Hard Mount Pedestals - Center punch all marks deep enough so that the marks are visible from the other side - Drill a 1/8 diameter pilot hole on all marks, then with an 11/32 diameter drill bit. Fig The left rear pedestal plate mounting holes may have to be drilled from the outside of the car (inside the wheel well). In that case re-center punch those particular marks from the outside, then drill. - Install right and left pedestal with hardware kit D and tighten down finger tight only. Fig.08,09 - Note: In the right rear fender well, the evap line will need to be relocated. Remove the evap line from the plastic clip. Spin the clip off of the stud it is mounted to. Enlarge the hole in the plastic clip to attach it to the protruding bolt from the pedestal mounting hardware. - Reinstall right and left seat belt retractors; torque to 30ft-lb - Reinstall carpet panels - Reinstall door sill trim. Install the 3 Phillips head screws but don t clip down the rest of the piece Fig. 07 Fig. 08 Step 4: Trim Interior Panels - Cut end link holes into right and left speaker panels: Fig Place template on panel accordingly and center punch. - Then, drill a 3/16 diameter pilot hole. - Peel away leather from panel with scribe or pick tool. - Flip panel over and with a 2-1/4 hole saw drill almost all the way through. - Carefully cut the rest of the circle with a utility knife and remove the piece. - De-burr or smooth the edges. - Relief cut the leather into 16 sections. - Spray contact cement onto underside of panel and leather. - Pull leather back and stick down on underside. - Warm up edge trim with a heat gun (or hair dryer) to soften glue inside. - Install edge trim and cut to appropriate length - Reinstall right and left speaker panels Fig. 09 Fig. 10 Fig. 11 Fig. 12
5 Step 4: Trim Interior Panels (cont.) Fig. 13 Fig. 14 Fig. 15 Fig. 16 Fig. 17 Fig. 18
6 Step 5: Hard Mount Main Hoop - Install right side main loop base with hardware package C: Remove 3 grommets from underside of car. Fig Use a magnetic holding tool to feed nut/stud through the floor (middle hole) and into the top two mounting holes. Fig A second person will have to install the washer and nut from inside the car. - To install bottom nut/stud, feed some.023 wire from the inside of the car through to the first hole on the underside of the floor, make a small loop and thread the stud into it, then pull it through. Fig. 21, Bolt together finger tight. - Install main loop: - Place right leg of main loop on cup of right base. Have left leg of main loop angled towards driver s side door opening and top of main loop tilted forwards. - Pull the top of the main loop rearward and the right leg should fall into place. - Now slip on the left base on to the left leg and swing the main loop into position. - Install hardware package C finger tight into left side main loop base - Install hardware package E finger tight into the base to main loop mounting holes - Install right and left lateral bars (put a bit of grease on end link faces) and finger tighten bolts Step 6: Torque Fig. 19 Fig Using a 5mm Allen Key in the end of the stud, tighten nuts on right and left bases - Make any necessary adjustments on end links and then tighten the bolts - Trim carpet as necessary around main loop base tube - Tuck carpet into door sill trim and position carpet appropriately - Tighten bolts for bases to main loop, right and left sides - Make sure ALL bolts are tightened down to the specs below: Torque Specs: The recommended torque specs for the hardware supplied with this are as follows: Fig. 21 M8-25 ft-lbs M10-47 ft-lbs M12-83 ft-lbs Step 7: Reassemble Cabin - Clip down door sill trim piece - Reinstall rear side trays, rear hatch trim and wiring and amplifier * - install horizontal seat belt bar (bit of grease on end link faces) and tighten end link bolts - Reinstall rear seats and passenger seats * Fig. 22 * Refer to standard VW installation procedures as outlined in the Bentley manual
7 CLUB-SPORT ROLL BAR: Volkswagen Mk4 Golf PACKING LIST: Inspected and Packed by: Date: (1) 1 x Main Loop (2) 4 x Bottom Pedestal Plates (3) 2 x Pedestal Hats (4) 1 x Left Pedestal (5) 1 x Right Pedestal (6) 1 x Harness Bar (7) 2 x Lateral Bars (8) 1 x Left Main Hoop Base (9) 1 x Right Main Hoop Base Hardware Package A: 6 x M12x30mm Socket Head Bolts Hardware Package B: 8 x M8x25mm Counter Sunk Socket Head Bolts 8 x 8mm nuts 8 x 8mm flat washers Hardware Package C: 6 x M10x30mm Socket Head Stud with pre-fitted nuts 6 x M10 Stover Nuts 6 x 10mm flat washers Hardware Package D: 16 x M8x30mm Hex Head Bolts 16 x M8 nuts 16 x 8mm Flat Washers 16 x 8mm Lock Washers Hardware Package E: 2 x M12x75mm Hex Head Bolts 4 x 12mm flat washers 2 x 12mm nuts 4 x concave spacers Additional Items: 2 x Paper Templates 1 length of Edge Trimmer 1 length of.023 Wire
Classic SportBar Camaro V6 or V8
Classic SportBar 2011-2015 Camaro V6 or V8 The Classic SportBar is intended for restyling purposes only and does NOT provide roll over protection. Read entire installation guide before starting. Component
More informationSTYLE BAR & TONNEAU COVER INSTALLATION
STYLE BAR & TONNEAU COVER INSTALLATION INSTALLATION MANUAL: 2005 to '09 Mustang P/N: 10-8002-C12071B Saleen Performance, Inc. 1225 East Maple Rd., MI 48083 800-888-8945 www.saleen.com 1 IF YOU ARE NOT
More informationJK FRONT FENDER FLARE INSTALLATION INSTRUCTIONS
JK FRONT FENDER FLARE INSTALLATION INSTRUCTIONS TOOLS NEEDED 3/16 Allen Wrench 1/2 Socket or wrench 10mm Socket Flat head screwdriver HARDWARE 5/16 x 3/4 button heads (14) 5/16 x 1 button heads (8) 5/16
More informationPARTITION INSTALLATION INSTRUCTIONS
PARTITION INSTALLATION INSTRUCTIONS 2015 Chevrolet Tahoe PPV / Part Number 5703FW, FWA & FEW Do not attempt to install this product on any vehicle equipped with third row seating! Parts List Distributed
More informationBushwacker Jeep Flat Style Fender Flares Front Pair
Bushwacker Jeep Flat Style Fender Flares Front Pair Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4 Hours Tools Required:
More informationINSTALLATION INSTRUCTIONS KK-K9-F14-K K9 KIT FOR FORD EXPEDITION
INSTALLATION INSTRUCTIONS KK-K9-F14-K-32 32 K9 KIT FOR 2003-2016 FORD EXPEDITION TOOLS REQUIRED: Power Drill Drill Bit Set Standard & Metric Socket Sets Phillips Screw Driver Open End Wrench Set Wire Cutters
More informationPickup Box Utility Rack Package Installation (Instruction ID: )
017 Chevrolet Colorado Pickup - WD (VIN S) Canyon, Colorado Accessory Installation Manual N America Document ID: 3966961 Pickup Box Utility Rack Package Installation (Instruction ID:3144879) Installation
More informationK9 KIT INSTALLATION INSTRUCTIONS CROWN VIC with Fire Suppression System Model KK-K9-F7-K-FS
K9 KIT INSTALLATION INSTRUCTIONS 2005-2011 CROWN VIC with Fire Suppression System Model KK-K9-F7-K-FS TOOLS REQUIRED: Power Drill (Cordless preferable) Drill Bit Set Standard Wrench and Socket Set Metric
More informationK9 KIT INSTALLATION INSTRUCTIONS CROWN VIC KK-K9-F7-K
K9 KIT INSTALLATION INSTRUCTIONS 1998-2011 CROWN VIC KK-K9-F7-K TOOLS REQUIRED: Power Drill (Cordless preferable) Drill Bit Set Standard Wrench and Socket Set Metric Socket Set Screwdriver Set Torx Bit
More informationCompetition Engineering 8 Point Roll Bar (94-04 Mustang)
Competition Engineering 8 Point Roll Bar (94-04 Mustang) Required tools: Socket set / Hand tools Welder of choice Welding blankets Welding safety gear Heat gun Putty knife Bar notching tool Adjustable
More informationInstallation Instructions Kit, Base Rail Bracket Part # 31413
Installation Instructions Kit, Base Rail Bracket Part # 31413 Dealer / Installer: Provide a copy of these Instructions to the end user of this product. These Instructions provide important operating and
More informationGiraud Tool Company, Inc.
Motor Upgrade for Gracey Trimmer This package is intended to allow the user to upgrade their Gracey trimmer with a higher rpm motor and convenience features not found in the production offering. This upgrade
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationINSTALLATION INSTRUCTIONS KK-K9-C12-K CHEVY IMPALA
INSTALLATION INSTRUCTIONS KK-K9-C12-K 2000-2005 CHEVY IMPALA READ ALL INSTRUCTIONS PRIOR TO INSTALLATION TOOLS REQUIRED: Power Drill Drill bits1/4 and 5/32 7/l6 wrench and socket 15,18 and\or 19mm socket
More informationMMD Convertible Styling Bar Customer Installation Guide
MMD Convertible Styling Bar Customer Installation Guide TOOLS REQUIRED/RECOMMENDED: Electric Drill 1 Forstner Bit (Hole Saw) 1 3/8 Hole Saw (manual calls for 1 ¾ ) 1/8, 3/8 & ¾ Drill Bits Rivet Gun Trim
More informationIsuzu D-Max Part Numbers Black Polished
SB007 Sports Bar Fitting Instructions Isuzu D-Max 0 Part Numbers - 55000 - Black - 5000 - Polished Installation Time: 0 min (Approximately) PLEASE KEEP INSTRUCTIONS IN GLOVE BOX FOR FURTHER USE RECOMMENDED
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Running Boards Kit Nissan Pathfinder/ Infiniti QX60 999T6 X5060 (Pathfinder Running Board Kit) 999T6 R5060 (Infiniti QX60
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationKWIK-KIT KK-S INSTALLATION INSTRUCTION PACKAGE
KWIK-KIT KK-S-120-02 INSTALLATION INSTRUCTION PACKAGE INSTALLATION INSTRUCTIONS HAVIS KWIK-KIT KK-S-120-02 2002-2007 DODGE/FREIGHTLINER SPRINTER VAN PLEASE READ COMPLETE INSTRUCTIONS PRIOR TO INSTALLATION
More informationTITAN2-EDGE Public Access Computer Station Dual Track
TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Rev A 6/17 Model TITAN2-EDGE ASSEMBLY AND ADJUSTMENT TITAN2-EDGE PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the
More informationIntroduction. Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions
Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions Introduction Thank you for purchasing the Rocky Mountain Westy Swing Away Carrier Kit. We pride ourselves in the products we develop
More informationWarnings. Description. Prior to Installation Tools Needed
Warnings Failure to act in accordance with the following may result in death or personal injury. The JT Strong Arm Stabilizer System is intended to eliminate chassis movement in travel trailers and fifth
More informationUSSC LLC 4 ONE LLC FIELD MODIFICATION INSTRUCTIONS
1 OF 17 A 1. PURPOSE: Instructions for in field replacement of 9004 mechanical suspension top pan 2. SCOPE: 9004 mechanical suspension with legacy two point LX back frame and current LX back frame 3. PROCEDURE:
More informationTOYOTA MOTOR EUROPE CA Products Division Tel : Fax :
TOYOTA MOTOR EUROPE CA Products Division Tel : + 32 2 745 26 77 Fax : + 33 2 745 26 99 Ordering part numbers Comments Part Numbers Wooden floor one hatch PZ449-D3C42-11 one hatch with carpet PZ449-D3C42-01
More informationRH-412 STEEL DOORS INSTALLATION INSTRUCTIONS
RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side.
More informationPROVEN WORLDWIDE SNORKEL FOR CHEVY COLORADO NEW PRODUCT
AEV30272AC Last Updated: 10/09/18 PROVEN WORLDWIDE SNORKEL FOR CHEVY COLORADO NEW PRODUCT Please visit www.aev-conversions.com to view the most current installation guide for this product. This is a new
More informationHatchback Wing Riser Kit
Hatchback Wing Riser Kit 2015-06-11 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket
More informationInstallation for Full Size Polaris Ranger Crew Doors
Installation for Full Size Polaris Ranger Crew Doors Order of Installation: Heater Doors Wiper on to Windshield Windshield Top & Back Panel Note: Most of the steps in these instructions need to be repeated
More informationINSTALLATION INSTRUCTIONS RH 412 STEEL DOORS
By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side. Note: Having the hood open makes the job
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SNYPER TUBULAR FENDERS APPLICATION: 2007-2017 Jeep Wrangler JK PART NUMBER: 62-1005, 62-1015 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1,2 2 FRONT FENDERS, DRIVER (1) AND PASSENGER
More informationSB-F-FOC5DR/10TW3 SKU# & Up Ford Focus 5 Door Hatchback
INSTALLATION GUIDE for the SB-F-FOC5DR/10TW3 SKU# 94560 2012 & Up Ford Focus 5 Door Hatchback If you choose to perform the installation yourself, it is absolutely vital that the Stealthbox be properly
More informationSB-F-FOC5DR/10TW3 SKU# & Up Ford Focus 5 Door Hatchback
INSTALLATION GUIDE for the SB-F-FOC5DR/10TW3 SKU# 94560 2012 & Up Ford Focus 5 Door Hatchback If you choose to perform the installation yourself, it is absolutely vital that the Stealthbox be properly
More informationFORD INTERCEPTOR SEDAN READY BUCKLE
INSTALLATION MANUAL FORD INTERCEPTOR SEDAN READY BUCKLE PART# FT3501RB We recommend you read through the installation guide prior to installation, if you have any questions please call us at 800-516-2322
More informationSTEP 1 : DESTROYER FRONT BUMPER INSTALL GATHER YOUR TOOLS AND LAY OUT YOUR PARTS... *shorty bumper to show hardware* Tools Required:
DESTROYER FRONT BUMPER INSTALL JL STEP 1 : GATHER YOUR TOOLS AND LAY OUT YOUR PARTS... Tools Required: - Utility knife - 11/16 Deep socket - Ratchet - 11/16 Crescent wrench - Ratchet Extension - 1/4 socket
More informationConflicts Note: Drop-in Bed liner
Toyota Tundra 2015 LED Bed Lights Preparation Part Number: 00016-34089 Accessory Code: BU1000 Conflicts Note: Drop-in Bed liner Kit Contents Item # Quantity Reqd. Description 1 1 Hardware Kit 2 1 Driver
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 33380 SIDE S 2007 S2000 Issue Date AUG 2006 PARTS LIST Left upper side strake 2 Grommets 2 Butyl O-rings 2 Washer-screws, 6 x 20 mm
More informationSCION tc 2005 PEDESTAL SPOILER Preparation. Part Number: PT47A XX PT47A XX PT47A XX
Preparation Part Number: PT47A-21052-XX PT47A-21062-XX PT47A-21082-XX Kit Contents Item # Quantity Reqd. Description 1 1 Painted Spoiler Assembly 2 1 LH Gas Strut 3 1 RH Gas Strut 4 1 Hardware Bag Hardware
More informationAssembly Instructions Nevins Phone Booth
Assembly Instructions Nevins Phone Booth Included Hardware Tools Required supplied by installer Drill & Bit Bolt A - (16) 1/4-20 x 1-1/2 hex head Bolt B - (20) 1/4-20 x 2-1/2 phillips head Screw 1 - (24)
More informationPart # 4463 & Ford Mustang C-Series Upper & Lower Grilles
Rev. 3/18 Page 1 Part # 4463 & 4464 2018 Ford Mustang C-Series Upper & Lower Grilles Notice: Install new, parts according to these instructions! Altered Parts are Non-Refundable! Part #4464 Notice: Part
More informationFitting Instructions. MGF Roll Bar Stainless Steel TT Style Roll Hoops TF New. Part No.: SWRB001
Fitting Instructions MGF Roll Bar Stainless Steel TT Style Roll Hoops TF New Part No.: SWRB001 MGF TWIN HOOP FITTING INSTRUCTIONS PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING THE WORK TOOLS REQUIRED
More informationCHEVY/GMC SuperRail Mounting Kit #3117
CHEVY/GMC SuperRail Mounting Kit #3117 #3100 SuperGlide (12K) Gross Trailer Weight (Maximum) Vertical Load Weight (Max. Pin Weight) 12,000 lbs. 3,000 lbs. Installation Instructions SPECIFICATIONS Fits
More informationPart# 85200, 86200, 85095, 86095, TC200,TT200,TC095,TT095
Part# 85200, 86200, 85095, 86095, TC200,TT200,TC095,TT095 Bag Hardware: (8) 5/16 x 1 ½ Allen flat head (14) 3/8 x 1 Hex bolt G5 (2) ½ x 2 ½ Hex Bolt G5 (6) 5/16 flange nuts (14) 3/8 flange nuts (2) ½ stove
More informationSTEP 1 STEP 2 LEVELER KIT OPTION MOBILE CASTER KIT OPTION
B SERIES INDUSTRIAL BENCHES TOOLS REQUIRED FOR ASSEMBLY Socket set, Open end wrench set, Cordless drill with 3/8" socket bit (Magnetic recommended). BEFORE ASSEMBLY Read through the assembly instructions
More information8030 Synergy Jeep JK Rear Long Arm Frame Brackets
General Notes: SYNERGY MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397 8030 Synergy Jeep JK Rear Long Arm Frame Brackets These instructions are also available on our website; www.synergymfg.com.
More informationJeep. Cut-Out Fender Flares Set of 4. Included in Hardware Kit: Set Part # Rev-8 06/29/16 STEP 1 PRIOR TO INSTALLATION
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationKawasaki Teryx 750 Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions.
Owner s Manual Model: Kawasaki Teryx 750 Kawasaki Teryx 750 Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions. Safety Instructions Cab Kit Contents Hardware
More informationAssembly Instructions Nevins Phone Booth
Assembly Instructions Nevins Phone Booth Included Hardware Tools Required supplied by installer Drill & Bit Socket Wrench Bolt A - (16) 1/4-20 x 1-1/2 hex head Bolt B - (20) 1/4-20 x 2-1/4 phillips head
More informationINSTALLATION INSTRUCTIONS FOR FRONT CASTING DECK RAIL Ranger
INSTALLATION INSTRUCTIONS FOR FRONT CASTING DECK RAIL Ranger TOOLS REQUIRED FOR INSTALLATION: Drill motor, (1) 5/16 inch drill bit, (1) 13/64 drill bit, (1) 3/16 inch hex wrench (1) 3/32 inch hex wrench.
More informationJK Front Crusher Flares
INSTALLATION INSTRUCTIONS INST-17-03-030_A JK Front Crusher Flares IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation.
More informationUnder Seat Storage Drawer Installation Instructions
Under Seat Storage Drawer Installation Instructions Parts List: 1) Drawer Assembly 8) Self Tapping Screws 1) Instructions 1) Template Tools Needed: Drill and/or Bit Driver Tape Measure Jigsaw or metal
More informationMM Strut Tower Brace, Cobra (MMSTB-7)
The MM strut Tower Brace attaches to each strut tower and to the firewall. 3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com MM
More informationINSTALLATION INSTRUCTIONS
NOTE: Bolts should remain hand tight until all bolts are installed. STEP 1 Installing the door base (both sides). 1. Locate the outer, roll cage, mounting bolt (passenger side is shown in the illustration).
More informationHARDWARE KIT # KKM or Rear Compartment: (Some hardware not used in all applications)
PRISONER TRANSPORT INSTRUCTIONS for CHEVROLET EXPRESS VAN PT-C01-100-2A TOOLS REQUIRED: Standard and Metric Socket Sets Awe or Scribe Tape Measure Impact Gun (recommended) Pry-bar Caulk gun Drill & drill
More informationMODULAR BUMPER INSTALLATION MANUAL
MODULAR BUMPER INSTALLATION MANUAL Parts List* 1 Center section 1 Side extension, passenger / right 1 Side extension, driver / left 1 Side cap, passenger / right 1 Side cap, driver / left 1 Brush guard,
More informationTIRE RACK INSTALLATION INSTRUCTIONS Dodge Sprinter
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 TIRE RACK INSTALLATION INSTRUCTIONS 07-11 Dodge Sprinter Please read before beginning Stainless steel hardware may bind together
More informationINSTALLATION MANUAL FRONT. See pages 2 and 3 of this manual for configuration options. Level of Difficulty. Product Photo (center section only)
INSTALLATION MANUAL FRONT Level of Difficulty Moderate Product Photo (center section only) All hardware listed below will be provided with the bumpers center section. Additional hardware will be supplied
More informationBe sure any accessory used will fit with the soft upper doors before installing. Not all accessories will be compatible.
Company Name: Spike Power Sports Vehicle Name: Polaris General 2P Product Description: Soft Upper Doors Part Number: 58-1600 Revision: R01 09/19/2018 Contents: 655 Elm Ridge Ave, Canal Fulton OH, 44614
More informationINSTRUCTIONS INSTRUCCIONES CONSIGNES
AUTOMOTIVE PRODUCTS, INC. INSTRUCTIONS INSTRUCCIONES CONSIGNES APPLICATION: 2007-2010 CHEVY/GMC SILVERADO/SIERRA 2500/3500 (EXCLUDES CLASSIC) APP PART #46-23715, 40-92315/45-92310 MAX WINCH TRAY, SPORTSMAN
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory FABRIC REAR DOORS (5P) P/N 0SR90-HL4-211B (BLACK) P/N 0SR90-HL4-211C (CAMO) Application SXS1000M5P/M5D Honda Dealer: Please give a copy of these instructions to your
More informationThor Audi A4/S4 Skid Plate Installation Instructions
Thor Audi A4/S4 Skid Plate Installation Instructions Parts List: 1 Aluminum Skid Plate 2 Aluminum Side Wings 10 10mm Flat Washers 3 8mm Flat Washers 3 8mm Speed Clips 2 10x40mm Bolts 3 8x35mm Bolts 2 Rivet-nuts
More informationBushwacker Jeep Flat Style Fender Flares Rear Pair (JK Wrangler 2dr)
Bushwacker Jeep Flat Style Fender Flares Rear Pair (JK Wrangler 2dr) Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4
More informationCustom 3-Point Seatbelt Installation Guide for: Corvette
Custom 3-Point Seatbelt Installation Guide for: 1963-67 Corvette Note: The information enclosed in this installation guide is to be used as merely an outline to assist you during the process of installation.
More informationCHEVY/GMC SuperRail Mounting Kit #4423
CHEVY/GMC SuperRail Mounting Kit #4423 #4100 SuperGlide (16K) #4400 SuperGlide (20K) Gross Trailer Weight (Maximum) Vertical Load Weight (Max. Pin Weight) 16,000 lbs. 4,000 lbs. Gross Trailer Weight (Maximum)
More informationADDICTIVE DESERT DESIGNS
Preparation: Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. We recommend reading through the installation instructions in whole before performing
More informationGared Pro-S Portable Backstop
Models: 9616 & 9618 Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE USE PUBLICATION
More informationWATSON RACING 4- & 6-POINT ROLL BAR Mustang Coupe p/n WR-15-BOLTINCAGE p/n WR-15-BOLTINCAGE6PT
1 WATSON RACING 4- & 6-POINT ROLL BAR 2015+ Mustang Coupe p/n WR-15-BOLTINCAGE p/n WR-15-BOLTINCAGE6PT The Watson Racing 4-Point & 6-Point Roll Bars were designed for superior strength while allowing for
More informationFord F150 Rear Flares Set Part # Revision
Ford F150 Rear Flares Set Part # 20074 Revision 1 04-01-09 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided.
More informationINSTRUCTIONS INSTRUCCIONES CONSIGNES
AUTOMOTIVE PRODUCTS, INC. INSTRUCTIONS INSTRUCCIONES CONSIGNES APPLICATION: GMC SIERRA 1500 HDX & SPORTSMAN GRILLE GUARDS (2014 & UP) APPLICATION PART # S 57-3690, 57-3695, 40-3695, 45-3690 ITEM QUANTITY
More informationSEATBELT SOLUTIONS, LLC.
Custom 3-Point Seatbelt Installation Guide for: 1963-67 Corvette Note: The information enclosed in this installation guide is to be used as merely an outline to assist you during the process of installation.
More informationINSTALL INSTRUCTIONS KK & KK KWIK-KIT PRISONER TRANSPORT INSERT FORD and CHEVY VAN PRISONER TRANSPORT
INSTALL INSTRUCTIONS KK-100-03 & KK-120-03 KWIK-KIT PRISONER TRANSPORT INSERT FORD and CHEVY VAN PRISONER TRANSPORT TOOLS REQUIRED: ¼ & 3/8 Ratcheting Wrenches ¼ & 3/8 Air Ratchets (recommended) 3/8 Impact
More informationSCION FR-S REAR SPOILER Preparation
Preparation Part Number: PT938-18130-XX Kit Contents Item # Quantity Reqd. Description 1 1 Spoiler 2 2 Strut 3 1 Hardware Bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 M6 x 1 Nut with
More information2015 Current Ford F150/Raptor Adaptive Cruise Control Module Relocation Bracket Installation Instructions
2015 Current Ford F150/Raptor Adaptive Cruise Control Module Relocation Bracket Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground
More informationADDICTIVE DESERT DESIGNS
Preparation: Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. We recommend reading through the installation instructions in whole before performing
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SPORTSMAN WINCH MOUNT GRILLE GUARD APPLICATION: 2016-2018 Toyota Tacoma PART NUMBER: 40-93885, 45-93880, 46-23885 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 WINCH TRAY 15MM SOCKET
More informationINSTALLATION INSTRUCTIONS AND PARTS LIST MODEL , O-MEGA II 6 OVAL STEPS
INSTALLATION INSTRUCTIONS AND PARTS LIST MODEL 583036, 584036 O-MEGA II 6 OVAL STEPS 1. READ INSTRUCTIONS COMPLETELY AND CHECK TO MAKE SURE THAT ALL REQUIRED PARTS (LISTED ON THE SERVICE PARTS LIST) ARE
More informationInstallation Instructions
86-95 Suzuki Samurai LROR Sport Cage Front (SKU# SRC-SCF) Installation Instructions Front and Rear Cage Combined CAUTION: Safety glasses should be worn at all times when working with vehicles and related
More informationInstallation instructions, accessories. TV receiver, digital
Installation instructions, accessories Instruction No 30756561 Version 1.1 5 Part. No. 30756181, 30756569 TV receiver, digital Volvo Car Corporation TV receiver, digital- 30756561 - V1.1 Page 1 / 36 Equipment
More informationframe bracket Dodge x 2 & 4 x 4 (6-1/2 & 8 Boxes Includes Mega Cab)
, Rev 4 02/19 frame bracket 8552026 Dodge 3500 4 x 2 & 4 x 4 (6-1/2 & 8 Boxes Includes Mega Cab) 14 5 7 2 4 11 9 10 17 3 6 1 8 13 15 16 18 12 ITEM PART # DESCRIPTION QTY. 1 00085.50 FLAT WASHER 10 2 00248
More informationMedium HoneyBadger Chase Rack Installation Instructions
PREPARATION Medium HoneyBadger Chase Rack Installation Instructions 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend reading
More informationINSTALL INSTRUCTIONS KK-XXX-02 XX-Specify length: FORD and CHEVY VAN PRISONER TRANSPORT INSERT
INSTALL INSTRUCTIONS KK-XXX-02 XX-Specify length: 80 100 120 FORD and CHEVY VAN PRISONER TRANSPORT INSERT TOOLS REQUIRED: ¼ & 3/8 Ratcheting Wrenches ¼ & 3/8 Air Ratchets (recommended) 3/8 Impact Guns
More informationINSTALLATION INSTRUCTIONS
Do not attempt to install this product on any vehicle other than the one it is designed for and listed above! Parts List 10 3/8 X 1 1/4 Hex Bolt 10 3/8 Lock Washer 4 3/8 Hex Nut 4 3/8 Flat Washer 2 3169)
More informationPLEASE READ INSTRUCTIONS THOROUGHLY BEFORE PROCEEDING
Part No. 8870 -or Part No. 9100-9110 Front Fender Flares Flat Panel Design 07-09 Jeep JK, 2/4 Dr. PLEASE READ INSTRUCTIONS THOROUGHLY BEFORE PROCEEDING We have provided complete instructions and specific
More informationJeep. Cut-Out Fender Flares Set of 4. Included in Hardware Kit: Set Part # Rev-6 7/20/15 For complete fitment info visit :
Jeep Cut-Out Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More information2017 Current Ford Raptor ADD Pro Front Bumper Installation Instructions
2017 Current Ford Raptor ADD Pro Front Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2.
More informationWATSON RACING 4- & 6-POINT ROLL BAR Mustang Coupe p/n WR-BOLTINCAGE p/n WR-BOLTINCAGE6PT
WATSON RACING 4- & 6-POINT ROLL BAR 2005-2014 Mustang Coupe p/n WR-BOLTINCAGE p/n WR-BOLTINCAGE6PT The Watson Racing 4-Point & 6-Point Roll Bars were designed for superior strength while allowing for installation
More informationAll Terrain Flares 09+ Ford F150
Page 1/5 Components: 1. Front Flares (2) 2. Front Flare Inner Pieces (2) 3. Rear Flares (2) Tools required: - Utility knife - Electric Drill - 1/4 Drill Bit - #2 Phillips driver - Socket wrench Hardware
More informationRubber Grommet, 36 pcs. 3/4 Screw, 10 pcs. Nut, 10 pcs
Jeep Cherokee ZJ Set Part #10916-07 Rev-2 03-11-10 THESE INSTRUCTIONS INVOLVE CUTTING THE FENDERS OF THE VEHICLE. IT IS IMPORTANT TO READ ALL INSTRUCTIONS PRIOR TO THE CUTTING AND INSTALLATION OF THESE
More informationSTELLA AUTO SIDECAR INSTALL INSTRUCTIONS
STELLA AUTO SIDECAR INSTALL INSTRUCTIONS Open crate and inspect sidecar Remove cardboard box from inside the sidecar Remove all hardware holding the sidecar to the crate Remove sidecar from crate Remove
More informationBMW E46 Coupe 3dr MP Bolt in (BMW Race Days Only) Roll Cage (B045) Fitting Instructions
BMW E46 Coupe 3dr MP Bolt in (BMW Race Days Only) Roll Cage (B045) Fitting Instructions Unwrap the mounting points/ends of the roll cage and unpack the individual fitting kits. Try to leave wrapping on
More informationCHEVY SuperBracket Mounting Kit #0826
CHEVY SuperBracket Mounting Kit #0826 #1200 SuperGlide (16K) #0800 SuperGlide (20.5K) Gross Trailer Weight (Maximum) Vertical Load Weight (Max. Pin Weight) 16,000 lbs. 4,000 lbs. Gross Trailer Weight (Maximum)
More informationSUT-1000CLC ASSEMBLY REQUIREMENTS
SUT-1000CLC Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16, 3/4, 13/16, and 7/8 sockets. ASSEMBLY REQUIREMENTS *Torque all
More informationWhalen Furniture Mfg. Factory No. 5 Page # 1
If you have any questions regarding assembly or if you are missing parts, do not return this item to Sam s Wholesale Club Please call our customer service number and have your instructions and parts list
More informationTYGER ARMORTM. Parts List BEFORE INSTALLATION WARNING. Customer Support TG-AM2C /8. x1 Driver/Left Side Armor
TYGER ARMORTM TG-AM2C20028 Customer Support Parts List x1 Driver/Left Side Armor BEFORE INSTALLATION READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS
More informationPPM-5710 JK HEAVY DUTY SKID PLATE ASSEMBLY Version 2.0
SYNERGY MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397 PPM-5710 JK HEAVY DUTY SKID PLATE ASSEMBLY Version 2.0 GENERAL NOTES: These instructions are also available on our website; www.synergymfg.com.
More informationINSTRUCTIONS INSTRUCCIONES CONSIGNES
AUTOMOTIVE PRODUCTS, INC. INSTRUCTIONS INSTRUCCIONES CONSIGNES APPLICATION: 2007 13 CHEVY SILVERADO 1500 (except Classic ) MAX WINCH TRAY: HDX 46-22275 SPORTSMAN WINCH MOUNT GRILLE GUARD: 45-92270, 40-92275
More informationIntercooler Shroud and Belt Cover for WRX
Intercooler Shroud and Belt Cover for 2015+ WRX 2016-05-18 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation
More informationDrake Off Road Hood Hold Downs Installation Guide
Installation Time: 30 Minutes Tools Required: Drake Off Road Hood Hold Downs Installation Guide 3/8 drive ratchet 13mm socket 10mm socket (deep-well socket helpful) 13mm wrench (2x) 4mm allen wrench 5mm
More informationINSTALLATION INSTRUCTIONS INTERIOR WINDOW GUARDS WGI-C1, C2, C3 & C CHEVROLET FULL SIZE WINDOW VANS
INSTALLATION INSTRUCTIONS INTERIOR WINDOW GUARDS WGI-C1, C2, C3 & C4 1997-2019 CHEVROLET FULL SIZE WINDOW VANS TOOLS REQUIRED: Power drill Safety goggles Hand jig saw Pencil Drill Bit Set File Set Phillips
More informationWPS crew Doors Installation instructions
WPS-132-133 crew Doors Installation instructions ORDER OF INSTALLATION FOR A COMPLETE ENCLOSURE OF A CREW WPS (Weather Protection System) IS AS FOLLOWS: 1. Heater 2. Rear Thresholds - Right Hand & Left
More informationCommander 2 Lift Kit
Commander 2 Lift Kit Can-Am Commander 2010+ Part #: 5102204 Rev. 082416 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-278-7768 E-mail: sales-rtpro@sporttruckusainc.com SAFETY WARNING RT Pro UTV
More information