Installation Instructions For Reveal Light Channel
|
|
- Nicholas Watson
- 5 years ago
- Views:
Transcription
1 2016 Pure ighting. All Rights Reserved. Installation Instructions For Reveal ight Channel IS# 902-RV-24VDC W. Fullerton Ave Chicago, I Tel: Fax: info@purelighting.com IMPORTAT IFORMATIO - Reveal channel can be used as a toe kick or for cove lighting. - This instruction shows a typical installation. SAVE THESE ISTRUCTIOS! Install the Junction Box (C-1RE-JBOX) A ADJUSTABE MOUTIG BAR PHIIPS MOUTIG BRACKET B #8 3 4 BOX 1 HORIZOTA ORIETATIO BOX 2 ADJUSTABE MOUTIG BAR VERTICA ORIETATIO 1: Mount each adjustable mounting bar to one side of the junction box (mounts to any side of the housing depending on the orientation of the channel) and secure them with the mounting brackets and two Phillips screws provided. OTE: The adjustable mounting bars mount to studs that are spaced 14.5" to 24" apart. 2: Select the location between the two studs for the junction box to be mounted. 3: Place the adjustable mounting bars between the studs. 4: Make sure the lips on the adjustable mounting bars are against the studs. Secure the adjustable bars to the studs with the eight #8 screws. C D DRYWA CUTOUT TEMPATE BOX CODUIT BOX FROM REMOTE PHIIPS 5: Remove the two Phillips screws to pull the drywall cutout template completely off the junction box face. Save the template and screws (these screws will be reused for step 9 on page 2). 1 6: Remove a knockout on the junction box to install conduit into the power feed electrical box. 7: Install the conduit and run the low voltage 24V DC power wires.
2 E 0.35" 3.00" 1.06" F CODUIT BOX 8 DRYWA CUTOUT TEMPATE DRYWA CUTOUT TEMPATE 2.25" 2.80" :Install the drywall. ROTOZIP DRYWA 8: Mark a location on the drywall where the junction box will be located. 9: Trace the drywall cutout template onto the drywall at the junction box location. 10: Remove drywall cutout template and cut out the marked area using a "Rotozip tool. G MARKIG EGTH OF COSE UP BOX SOT START 2.25" CUTOUT DRYWA OPEIG 12: Using the drywall opening as reference, mark 2.25" wide lines the complete length of the channel along the drywall. 13: Cut out the mark line on the drywall. 14: Mark the location to the studs for future reference. H ED CAP ED CAP 15 REVEA 15: Remove one included power feed end cap from the channel end opposite the junction box. 2
3 I J JOIIG ROD 16 ED CAP DEAD ED CAP OTE: Channel may be cut in the field. For installation over 120" join two or more Reveal channels together shown on diagram B. REVEA OTE: It is recommended more than one person to install the Reveal channel. 16: OPTIOA: Insert the joining rods half way into the each channel circular ends sliding them towards each other. 17: Install the dead end cap to the end of the channel opposite the junction box. K WOOD CODUIT BOX BOX SOT PHIIPS : Connect the red power supply (24VDC+) wires to each red power wire with a wire nut inside the electrical box. 21 ED CAP FAGE 23 19: Connect the black power supply (24VDC-) wires to each black power wire with a wire nut inside the electrical box. 20: Place the wire nut connections inside junction box. 21: Align the power feed end cap into the junction box opening slot and push channel into the drywall cutout. 22: Make sure channel is aligned straight using a laser level. 23: Insert the power feed end cap into the junction box slot and align the channel to the drywall cutout. First secure the channel using the two Phillips screws to the junction box (same screws as in step 5 page 1) followed by fastening the drywall screws through the pre-drilled holes onto the studs. If necessary drill new holes on channel flange where they line up with the studs using the #6 X 1-5/8" square trim screw with the square recess bit provided. OTE: Make sure screw head is flush with the channel flange. 3
4 M PASTER BUE COTRACTORS TAPE WA PASTER 24: Cover up the opening section of the Reveal channel with contractors blue tape to prevent plaster and dust entering inside the channel. FEMAE POWER COECTOR + - EFT ED O SIDE VIEW 25: Plaster the channel flange edge to the wall & fill screw holes (highlighted in green). Finish the wall properly. 26: Remove the blue contractor tape & clean the inside of the channel. 27 (BACK OF ) COVER MAE ED MAE ADAPTER FEMAE ED (BACK OF ) RIGHT ED REVERSE POARITIES FEMAE POWER COECTOR 31 PHIIPS PASTER MUST BE ISTAED HERE 29 GOES HERE TEST ED & COECTOR, PRIOR TO POWER!!! OTE: If installation requires RGB, RGB+W, or Tunable White, refer to wiring diagrams on pages : If the male end of the soft strip is facing the power electrical box, then connect the female power connector to the male soft strip connector so that the red wires of the power connector are inline with the "+24VDC" marking of the soft strip. 28: If the female end of the soft strip is facing the power electrical box, then connect the male adapter to the female soft strip and power connector so that the black wires of the power connector are inline with the "+24VDC" marking of the soft strip. 31: Make sure all wire connections are inside the junction box and install the electrical box cover with the provided two screws. 32: OPTIOA: For the other side of the channel, extra cover is included that can be mounted to the drywall using drywall screws to secure in place. 33: OPTIOA: For cleaner finished look apply plaster over screw holes and end cap edges. 29: Remove the backing from the soft strip and installed it inside the channel. Make sure that the soft strip is firmly attached to the channel. 30: After trimming the soft strip on cuttable section, place the excess soft strip behind the drywall 4
5 General Wiring Diagram IGHTOIER: ZP600FAM120 PSB-96W VDC IPUT +24VDC 4 WIRES FOR 0-10V DIMMIG REVEA General 24VDC Configuration IPUT (HOT) EU BACK (HOT) WHITE (EUTRA) EV DIMMER 24V ED Standard RGB Configuration CDP Using ED Power Supply with RGB Soft Strip & CDP or CTP Control EXT in- EXT in+ DMX in shield out+ VDC- out- VDC+ out shield 24VDC + - IE VDC+ VDC- ED supply + Ext in- Group 1 - Ext in+ Group 2 - DMX CABE DMX in shield edsync thru+ edsync thru- edsync shield M DVR-RGB Group 3 - Group 4 - RGB ED 5
6 RGB+W Configuration CDP Using ED Power Supply with RGB+W Soft Strip & CDP or CTP Control EXT in- EXT in+ DMX in shield out+ VDC- out- VDC+ out shield 24VDC + - IE VDC+ VDC- ED supply + Ext in- Group 1 - Ext in+ Group 2 - DMX CABE DMX in shield edsync thru+ edsync thru- edsync shield M DVR-RGB Group 3 - Group 4 - RGB+W ED Tunable White Configuration Dual Power Supplies Controlled Via Individual EV Dimmers EV DIMMER WHITE (EUTRA) IPUT BACK (HOT) (HOT) EU HOT Power Supply +24VDC RED -24VDC BACK WHITE (EUTRA) IPUT BACK (HOT) (HOT) EU HOT Power Supply +24VDC RED -24VDC BACK EV DIMMER 6
7 +24VDC Tunable White Configuration RGB Power Supply with DMX Controller CDP/CTP or other DMX Signal From Any Compatible Controller If using a CDP Color Dial, configure your CDP to Warm White mode using DIP switches and follow CDP operating instructions: O ED SYC OUT + ED SYC OUT - ED SYUC OUT SHIED Power Supply 24VDC + RED - BACK VDC+ VDC- DMX Cable (belden #9841 or CATS) Ext in- Ext in+ DMX in shield edsync thru+ edsync thru- edsync shield M Driver ED supply + Group 1 - Group 2 - Group 3 - Group
Installation Instructions For Reveal
2017 Pure Lighting. All Rights Reserved. Installation Instructions For Reveal IS# 902-RV-24VDC-07 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1196 Fax: 773-883-6128 www.purelighting.com info@purelighting.com
More informationInstallation Instructions for TruLine 1.6A 24VDC. Section One: Basic Configuration Options
Doc # 902-TL1.6A_07 1718 W. Fullerton Chicago, IL 60614 Ph: 773.770.1195 Fax: 773.935.5613 www.pureedgelighting.com info@pureedgelighting.com 2016 PureEdge Lighting. All Rights Reserved. Installation Instructions
More informationInstallation Instructions For TruLine 1.6A 24VDC
2014 Pure Lighting. All Rights Reserved. Installation Instructions For TruLine 1.6A 24VDC INS# 902-TL1.6A-07 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195 Fax: 773-935-5613 www.purelighting.com
More informationInstalling Fixture Using Remote Power Supply
2017 Edge Lighting. All Rights Reserved. 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195 Fax: 773-935-5613 www.edgelighting.com info@edgelighting.com 904-BV2-2K4K-_03 BV2-1RE-_-2K4K-_ Installation
More information3% VOLTAGE DROP. Installation Instructions for 400 Watt 24 Volt DC RGB DMX LED Power Supply SAVE THESE INSTRUCTIONS!
Installation Instructions for 400 Watt 24 Volt DC RGB DMX LED Power Supply Doc # 904-PSB-400W-24VDC_06 1718 W. Fullerton Chicago, IL 60614 Ph: 773.770.1195 Fax: 773.935.5613 www.pureedgelighting.com info@pureedgelighting.com
More informationInstallation Instructions for TruLine 1A Center Feed Power Channel Connector
IMPORTANT INFORMATION - This instruction must be used concurrently with other TruLine A BIY installation instructions. - This product is wall or ceiling mount. - This instruction shows a typical installation.
More informationSLOT INSTALLATION GUIDE Indoor IP20
Please read entire guide prior to starting installation. Sections: Pre-Installation Single Run Fed From Both Ends NOTES 1. IP40 and lower tape must be installed indoors only. Installing outdoors will void
More informationInstallation Instructions For Aurora Dual MR16 Round & Square Edge 3.3" Fig.1 Complete Fixture ADJUSTABLE GEARS HIDDEN BEHIND THE LAMP PAN LOCK
2015 Pure Lighting. All Rights Reserved. Installation Instructions For Aurora Dual MR16 Round & Square Edge 3.3" 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195 Fax: 773-935-5613 www.purelighting.com
More informationINSTALLATION INSTRUCTION Indirect Recessed Channel
SAFETY INSTRUCTION IMPORTANT: NEVER attempt any work without shutting off the electricity. Read all instructions before installing. Always turn off power at fuse box prior to installation to prevent electrical
More informationInstall the Housing. Installation Instructions for Entra Round or Square Type IC, Air-tight New Construction Adjustable LED Housing EN3_-LH9_ 1.
Installation Instructions for Entra Round or Square Type IC, Air-tight New Construction Adjustable LED Housing 90ENTRA EN_-LH9_. LED - ROUND/ SQUARE GENERAL PRODUCT I NFORMATION: This product is safety
More informationAURORA HALOGEN ACCENT HOUSING 3 ROUND AND SQUARE TRIMLESS AH3-ARE3-RBG & AH3-ASE3-RGB INSTALLATION INSTRUCTIONS
AURORA HALOGEN ACCENT HOUSING 3 ROUND AND SQUARE TRIMLESS AH3-ARE3-RBG & AH3-ASE3-RGB INSTALLATION INSTRUCTIONS Fixtures must be installed by a qualified electrician (check with local and national codes
More informationConnecting the Channel A
20 Edge Lighting. All Rights Reserved. Installation Instructions for Cirrus Channel Suspension T, Tubular Lens w/2sq or 2RD Canopy IMPORTANT INFORMATION - This product is suitable for indoor locations.
More informationMultiples EM_ 1.4. Install 1X1/1X2/1X3/1X4 Housings. Installation Instructions for. This product is suitable for indoor locations.
Installation Instructions for 90EMULTI Multiples EM_. GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations. This product can be dimmed with a standard electronic dimmer or a 0-0V
More informationInstallation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH2-ARE3 & AH2-ASE3. Fig.1 Complete Fixture
015 Pure Lighting. All Rights Reserved. Installation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH-ARE3 & AH-ASE3 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195
More informationInstallation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH1-ARE, AH1-ARB, AH1-ASE, AH1-ASB. Fig.
2015 Pure Lighting. All Rights Reserved. Installation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH1-ARE, AH1-ARB, AH1-ASE, AH1-ASB 1718 W. Fullerton Ave Chicago, IL 60614
More informationInstallation Instructions for DIY or Completed 45 Degree Light Channel
201 Edge Lighting. All Rights Reserved. Installation Instructions for DIY or Completed Degree Light Channel IMPORTANT INFORMATION - This instruction shows a typical installation. 11 W. Fullerton Ave Chicago,
More informationInstallation Instructions for DIY or Completed Light Channel.6 Millwork
2017 Edge Lighting. All Rights Reserved. 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 77-770-1195 Fax: 77-95-561 www.edgelighting.com info@edgelighting.com LCMW.6- - - 904-LCMW.6_02 Installation Instructions
More informationC 0.05" ALLEN WRENCH. Installation Instructions for Cirrus Channel Suspension T1 with 4" Square or Round Canopy. Section One: Adjusting Cable Position
Doc # 90-CST-SQ_0 W. Fullerton Chicago, IL 0 Ph:.0.9 Fax:.9. www.pureedgelighting.com info@pureedgelighting.com 0 PureEdge Lighting. All Rights Reserved. Installation Instructions for Cirrus Channel Suspension
More informationInstallation Instructions for Zip Suspension Downlight with Remote Power and 4" Square or Round Canopy
Doc # 90-ZS-SQ_0 W. Fullerton Chicago, IL 0 Ph:.0.9 Fax:.9. www.pureedgelighting.com info@pureedgelighting.com 0 PureEdge Lighting. All Rights Reserved. Installation Instructions for Zip Suspension Downlight
More informationInstallation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH2-ARE3 & AH2-ASE3. Fig.1 Complete Fixture
015 Pure Lighting. All Rights Reserved. Installation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH-ARE3 & AH-ASE3 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195
More informationLightplane 3.5 Recessed
INSTALLATION INSTRUCTIONS Lightplane 3.5 Recessed LP3.5R Recessed Ceiling IMPORTANT SAFETY INSTRUCTIONS When installing or using this fixtures basic safety precautions must be followed. Read all instructions
More informationASSEMBLY INSTRUCTIONS. enook Pro
ASSEMBLY INSTRUCTIONS enook Pro Product enook Pro for Monitors, 36w Part# EPM3616zz/xx Anthro Corporation 10450 SW Manhasset Dr. Tualatin, OR 97062 Toll-free: 800.325.3841 Fax: 800.325.0045 email: sales@anthro.com
More informationInde-Pendants Family. 32L Ring Plaster Trim, Grid and Drywall Ceiling Types. Document No Installation instructions for 32L-Rxx-P
Inde-Pendants Family 32L Ring Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-Rxx-P Document No. Supplied by Litecontrol 32L Inde-Pendants: Ring (Plaster Trim, Grid and Drywall
More informationFigure A. Figure B. Figure C. Figure D
Xsite 1 Power/Data Tile and Components Tools Required Tape Measure Cordless Drill/Driver #2 Phillips Screw driver bit Rubber Mallet Flat Blade Screwdriver Figure A Hardware Required Provided as shown Installation
More informationCellular SlumberShade
Cellular SlumberShade with energy saving blackout sidetracks Installation Instructions 152110 1/6/2011 BASICS A few simple tools are required: - Measuring tape - Power drill, drill bits - Hex head and/or
More informationTREX PERGOLA INSTALLATION INSTRUCTIONS
RECOMMENDED TOOLS/SUPPLIES: Pencil 4' Level Measuring Tape Framing Square/Speed Square 8' High Step Ladder (Two recommended) Hacksaw or Bolt Cutters Socket Wrench with 9/16" Socket and 3/4" Deep Socket
More informationMESO X1 TBAR SEMI-RECESSED
MESO X1 TBAR SEMI-RECESSED 93t-inst PAGE 1 OF 2 1 2 A IMPORTANT Do not remove packaging around fixture until after fixture is installed. The packaging protects and in some cases supports the fixture during
More informationInstallation Instructions for Cirrus Suspension Downlight with Power - End Feed. Section One: 4" Flush Canopy Version
Doc # 0-CSP-E_0 W. Fullerton Chicago, IL 606 Ph:.0. Fax:..6 www.pureedgelighting.com info@pureedgelighting.com 06 PureEdge Lighting. All Rights Reserved. Installation Instructions for Cirrus Suspension
More informationInstallation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH3-ARE3-RGB & AH3-ASE3-RGB. Fig.
0 Pure Lighting. All Rights Reserved. Installation Instructions For Aurora Halogen Accent Housing Round & Square Trimless AH-ARE-RGB & AH-ASE-RGB W. Fullerton Ave Chicago, IL 606 Tel: -0-95 Fax: -95-56
More informationInde-Pendants Family. 32L Surface Mount Cylinder with Ring Plaster Trim, Grid and Drywall Ceiling Types. Document No
Inde-Pendants Family 32L Surface Mount Cylinder with Ring Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-CRxx-S-D Document No. Supplied by Litecontrol 32L Inde-Pendants:
More informationInde-Pendants Family. 32L Surface Mount Cylinder Plaster Trim, Grid and Drywall Ceiling Types. Document No
Inde-Pendants Family 32L Surface Mount Cylinder Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-C-S-D Document No. Supplied by Litecontrol 32L Inde-Pendants: Cylinder (Surface
More informationDrywall with Plaster and Paint. Lamp: The average LED Life is 50,000 hours. per Foot. per Watt. (2x2.5WDC) (2x5WDC) (2x6WDC)
Drywall Drywall with Plaster and Paint 3.73" (9.5cm) 1" (2.5cm) 6" (15.2cm) 1'- 40' (30.5cm - 1219.2cm) Description: TruLine 1.6A, a versatile 24VDC linear plaster-in LED system, creates glare-free, indoor
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationSTEP BY STEP INSTALLATION INSTRUCTIONS. Honeycomb Shades. Stationary Arch
STEP BY STEP INSTALLATION INSTRUCTIONS Honeycomb Shades Stationary Arch Everything You Need A Smooth Set-Up We want you to love your new window coverings and that includes having a smooth installation
More informationSeriesTWO RGB Fluorescent Fixtures. Installation and Instruction Manual
SeriesTWO RGB Fluorescent Fixtures Installation and Instruction Manual Brightline LP 580 Mayer Street #7, Bridgeville PA 15017 Phone 1-412-206-0106 Fax 1-412-206-0146 www.brightlines.com The Brightline
More informationInstallation Instructions
Installation Instructions Follow these simple instructions to install your OneDayCab! IMPORTANT: Unpack and check shipment for damage. Verify color, size and parts before demolition. Installation of interiors
More informationLINESSE LINEAR LUMINAIRE 3 RECESSED CV2424
Linesse Linear Luminaire 3 Recessed LINESSE LINEAR LUMINAIRE 3 RECESSED Page 2: Warnings Page 3: Mounting Types and Dimensions Page 4: T-Grid and Joining Fixtures Page 5: Hard Ceiling and Joining Fixtures
More informationLamp: The average LED Life is 50,000 hours. per Foot 2WDC (2.5WDC) per Watt. per Foot 5WDC Lumen values are based on the 3000K LED test.
Drywall Drywall with Plaster & Paint 2" (5.1cm) 1" (2.5cm) 6" (15.2cm) 1'- 40' (30.5cm - 1219.2cm) Description: TruLine.5A, a versatile 24VDC linear plaster-in LED system, creates glare-free, indoor architectural
More informationTIP FOR GETTING STARTED
Tip for getting started TIP FOR GETTING STARTED Be careful not to drill into any electrical wires, ductwork, plumbing or other damagable components. If you have any questions on the locations of these
More informationWalk-in Configurations
Walk-in Configurations Includes Wall-to-Open, Corners, and Corner Rounder Bars INSTALLATION INSTRUCTIONS Tools needed: Tape measure, level, pencil, #2 Phillips head screw driver or power drill with a 6"
More informationINSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE
T F W 604.549.979 604.549.9555 fluxwerx.com INSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE fixture housing endcap kit optic kit join kit notch 2 cross section notch 4 cross section 4 4" 4-11/2" 4 /8 (111)
More informationNX7 SERIES 5-1/2 HANDRAIL
STORAGE & HANDLING The handrails are shipped unassembled. Upon receipt, immediately check all material for any damage that may have occurred in transit and verify that all of the items and quantities are
More informationInstallation Instructions for: Saris Cycle Aid. Saris Cycle Air. Saris Cycle Air HD
Installation Instructions for: Saris Cycle Aid Saris Cycle Air Saris Cycle Air HD A. Setbacks Parallel Wall or object Setbacks: Both sides of the Saris Cycle Aid should be at least 48 from walls or other
More informationINSTALLATION GUIDE Hisense Laser TV Display Screen
INSTALLATION GUIDE Hisense Laser TV Display Screen Before you install this product, read this guide completely and make sure you understand all of the content. ES-G1811M2-1 ENGLISH Product Description
More informationAssembly Instructions
Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt
More informationAssembly Instructions
InTandem Table System November 20 InTandem Table System - Worksurface #4 x/" 4 wood screw power beam Tools Provided T-0 Extended Torx Driver T-25 Torx Driver Additional Tools Required Soft protective
More informationHawko LED Flex & Accessories Installation Instructions
LED Flex & Profiles Hawko LED Flex & Accessories Installation Instructions Contents Installation of IP20 LED Flex 4 Installation of IP67 LED Flex 6 Mounting Channel Installation 8 Mounting Clip Installation
More informationRound or Square Chicago Plenum Down Light Housing with Lamp
Installation Instructions for 90ELED-DCP Round or Square Chicago Plenum Down Light Housing with Lamp LED E_-L_DC. LED - ROUND/ SQUARE GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations.
More informationED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS
ED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS Ver.2 1300 SERIES CONCEALED VERTICAL ROD DEVICE Top Strike Latch Screws Strike Screws Release Plunger Top Latch Plunger Screws
More informationwith Lamp Install the Housing with Adjustable Bars Installation Instructions for LED E3_-L_DN 1.1 ½ to ¾ ¾ or thicker
Installation Instructions for 90ELED-D Round or Square Type IC, Non-IC Down Light Housing with Lamp LED E_-L_DN. LED - ROUND/ SQUARE GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations.
More informationDrywall with Plaster and Paint. 6" - 400" (15.2cm cm) Lamp: The average LED Life is 50,000 hours. per Foot. per Watt. per Foot (2.
TruQuad 1A, 24Vdc Plaster-In LED system Drywall Drywall with Plaster and Paint 6" (15.2cm) 6" (15.2cm) Description: TruQuad 1A, a versatile 24VDC linear plaster-in LED system, creates glare-free, indoor
More informationINDIVIDUAL MOUNTING: T-Bar
X1 (T-BAR) INSTALLATION INSTRUCTIONS GENERAL NOTES NOTE : Additional support to structural member may be required. Check with local building codes for requirement. 1. Place troffer clamp approx. 6 from
More informationINSTALLATION GUIDE. Model:B60 RECESSED IN WALL MOUNT
INSTALLATION GUIDE Model:B60 RECESSED IN WALL MOUNT Features: Installs between 16 (406mm) wood stud centers Mounting Pattern Compliance: VESA 100*100mm up to 600 x 400mm Level 5 degree horizontal adjustment
More informationInstallation, Operation and Care Instructions. Retractable Cord Operating System
Installation, Operation and Care Instructions Retractable Cord Operating System CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3 Mount
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More information955 Industrial St NE, Pine City MN Telephone: / Fax #218 LARGE MULTI-SPEED BLOWER & FILTER BOX KIT
955 Industrial St NE, Pine City MN 55063 Telephone: 320.629.6737 / Fax 320.629.3677 www.dakacorp.com #218 LARGE MULTI-SPEED BLOWER & FILTER BOX KIT INSTALLATION INSTRUCTIONS FOR DAKA FURNACES SECTION 1:
More informationFLEXDC INSTALLATION GUIDE
Please read entire guide prior to starting installation. NOTES 1. IP40 and lower tape must be installed indoors only. 2. Installation must be carried out by a licensed electrician & executed in accordance
More informationQUANTUM 2 CIRCLE 24 Installation Instructions
Installation Instructions #CH-C-24-KIT #CH-C-24-2FT #CH-C-24-4FT #CH-C-24-6FT #CH-C-24-8FT Custom #CH-C-24 Sections: Pg. 2 Fixture Kit Channel Preparation Pg. 6 Suspension Installation Version 3 Page 1
More informationJoiner Kit Joiner bracket (x1) Biscuit aligners (x2) Trim Flange
- Trim System Overview These instructions review how to install TruGroove Perimeter fixtures. Modules can be installed as individual standalone units, or they can be joined together to create continuous
More informationPHTM200 - Phantom 200 Flat Screen Wall Mount with Wafer Thin Projection Fits Screens up to 50 lbs with 200mm Mounting Patterns
PHTM200 - Phantom 200 Flat Screen Wall Mount with Wafer Thin Projection Fits Screens up to 50 lbs with 200mm Mounting Patterns Features: Durable high quality gloss black baked on powder coat finish Fits
More informationQUANTUM 2 TRAPEZOID 2509 Installation Instructions
Installation Instructions #CH-T-2509-KIT #CH-T-2509-2FT #CH-T-2509-4FT #CH-T-2509-6FT #CH-T-2509-8FT Custom #CH-T-2509 Sections: Pg. 2 Fixture Kit Channel Preparation Pg. 6 Suspension Installation Version
More informationInsolroll Clutch Operated Shades Installation Instructions Installation Instructions
All clutch operated shades are shipped fully assembled and ready for installation. Mounting screws are not provided. Screws for chain guide installation to meet the child safety standards are provided.
More informationCellular Shades SLUMBERSHADE. with energy saving blackout sidetracks. Installation & Care Instructions
Cellular Shades SLUMBERSHADE with energy saving blackout sidetracks Installation & Care Instructions 152725 B 9/14/2017 GETTING STARTED A few simple tools are required: - Measuring tape - Power drill,
More informationTOOLS REQUIRED Metal Wood Wood and Metal Screws. #16 Drill #12-24 Tap. 1/8 Drill
DEVICES COVERED IN THIS DOCUMENT: 4700S Surface Vertical Rod Device 4700SF Fire Exit Surface Vertical Rod Device TOOLS REQUIRED Metal Wood Wood and Metal Screws Sex Bolts #7 Drill ¼ -20 Tap #16 Drill #12-24
More informationInstallation Manual MODEL AE-46
Installation Manual MODEL AE-46 GET TO KNOW YOUR UNIT (BOTTOM OF RACEWAY) 2 5 1 4 6 3 1. CROSS BRACES 2. ELECTRICAL RACEWAY 3. SIDE BRACKETS 4. ELECTRICAL CORD COVER 5. ELECTRICAL OUTLET 6. HOT IRON REST
More informationTOYOTA MOTOR EUROPE CA Products Division Tel : Fax :
TOYOTA MOTOR EUROPE CA Products Division Tel : + 32 2 745 26 77 Fax : + 33 2 745 26 99 Ordering part numbers Comments Part Numbers Wooden floor one hatch PZ449-D3C42-11 one hatch with carpet PZ449-D3C42-01
More informationTrendWall Floor-To-Ceiling Panels Installation Instruction
TrendWall Floor-To-Ceiling Panels Installation Instruction TrendWall Components Covered by this Instruction: Crown (and accessories) Floor Plate Solid Panel Filler Panel Wall Channel Door Section Pilaster
More informationcompile system INSTALLATION GUIDE Updated January 2019
INSTALLATION GUIDE Updated January 09 compile system Table of Contents Panels 0 Quick Connect Clips 0 Lock Clips 0 Panel Trims 0 Privacy Glass 0 Post Base Covers 04 Electrical 04 Power Distribution Harness
More informationInstallation Instructions Parasol Cellular Shades
Installation Instructions Parasol Cellular Shades SlideArch CONTENTS Getting Started: Product View...1 Tools and Fasteners Needed...2 Installation: Installation Overview... Mount the Installation s Inside
More informationMantelMount. TM1A Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MantelMount TMA Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS TM Thank you for choosing the MantelMount television wall mount. Please read this entire manual before
More informationTransform your space into an extraordinarily inviting home, office or gathering place with the versatile, powerful and elegant Olin Fixture system.
OLIN FIXTURES Transform your space into an extraordinarily inviting home, office or gathering place with the versatile, powerful and elegant Olin Fixture system. This new Trulux collection introduces
More informationBox Track INSTALLATION INSTRUCTIONS
Box Track INSTALLATION INSTRUCTIONS BOX TRACK Recommended Tools Level Tape Measure Pencil Drill with 1/8, and 1/4, Drill Bits, Phillips Bit and Slotted Bit Socket Wrench with 9/16 Socket 9/16 and 5/8 Wrench
More informationJohn Deere 9570STS, 9650STS, 9660STS, and 9750STS Grain Tank Cross Auger Trough Liner EXOPLATE INSTRUCTION MANUAL
PLEASE READ THE ENTIRE INSTRUCTION SHEET BEFORE STARTING INSTALLATION. PLEASE REFER TO THE OPERATORS MANUAL FOR YOUR SPECIFIC COMBINE FOR PERTINENT SAFETY PRECAUTIONS THE TERMS. LEFT, RIGHT, FRONT, & REAR
More informationPreference Collection and Treatment Console INSTALLATION GUIDE
Preference Collection 5580.69 and 5580.96 Treatment Console INSTALLATION GUIDE WARNING Failure to install the 5580 as described in this installation guide may cause the unit to collapse, resulting in serious
More informationHONEYCOMB & PLEATED Standard Shades Top Down Bottom Up
HONEYCOMB & PLEATED Standard Shades Top Down Bottom Up INSTALLATION INSTRUCTIONS Rev. 8/2018 BASICS A few simple tools are required: Measuring tape Power drill, drill bits Hex head and/or Phillips driver
More informationTruLine TruQuad.5A 24VDC - PLASTER-IN LED SYSTEM
Drywall Drywall with Plaster & Paint 6" (15.2cm) 2.62" (6.7cm) 6" (15.2cm) 2" (5.1cm) 6" - 400" (15.2cm - 1016cm) 6" - 400" (15.2cm - 1016cm) 6" - 400" (15.2cm - 1016cm) 0.63" (1.6cm) DESCRIPTION TruQuad.5A,
More informationSURFACE CLIP MOUNT. 1 Insert lens into channel, measure, and cut to length. Remove lens cover from channel. surface. Attach lens cover and end caps
SURFACE CLIP MOUNT 1 Insert lens into channel, measure, and cut to length Remove lens cover from channel Screw mounting clips into mounting Snap channel into mounting clips Attach lens cover and end caps
More informationSteel Solutions USA 602 E. Walnut Street Watseka, IL p: (888) f: (815)
Steel Solutions USA 602 E. Walnut Street Watseka, IL 60970 p: (888) 875-5004 f: (815) 432-3364 sales@steelsolutionsusa.com Published February 2011 2011 Steel Solutions USA. All rights reserved. version
More informationINSTRUCTIONS TS93 GSR PT RIGHT HAND ACTIVE LEFT HAND INACTIVE RIGHT HAND INACTIVE LEFT HAND ACTIVE
INSTRUCTIONS ATTENTION!!! Before you begin, determine installation type (RIGHT HAND ACTIVE OR INACTIVE). Door coordinator suitable for door from 59 to 98 in width. Inactive door width in the case of unequal
More informationMobileTrak5 Installation Instructions
MobileTrak5 Installation Instructions PLEASE OPEN ALL BOXES & CHECK TO MAKE SURE YOU HAVE ALL PIECES REQUIRED READ ALL INSTRUCTIONS BEFORE STARTING Tools Required for Assembly 7/16, 1/2 Wrench Phillips
More informationEND FEED INSTALLATION
STARLINE PLUG-IN RACEWAY END FEED INSTALLATION The Universal End Feed (product numbers beginning with URPF, URDF, or MRPF, MRDF) provides the installer a provision to connect supply power to the Plug-In
More informationLF Series Assembly Instructions
LF Series Assembly Instructions 1998760 Revision A-10 Complete Series Master Packet 2010 Kimball International, Inc. T 800.482.1818 F 812.482.8300 Footprint Storage and Metal Filing Systems Assembly Instructions
More informationINSTALLATION INSTRUCTION Silo Multiples - New Construction Housing MT-4*15, MT-4*10
IMPORTANT SAFETY INSTRUCTIONS 1. Read all instructions before installing. 2. System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.
More informationDRYWALL CEILING SPLINE KICKER REFLECTOR DIFFUSER LENGTH TABLE DIFFUSER LENGTH TABLE DESCRIPTION 2' IND 3' IND 4' IND 6' IND 8' IND
SUPPLEMENTAL INSTALLATION TYPE LG-WWD-44, R-WWD-44 & RP-WWD-44 510553-2000 WHICH IS CONTRARY TO THE CONTAINED HEREIN. P/C PG. 1 OF 1 1/4-20 THREADED ROD OR EQUAL SUPPLIED PANHEAD SHEET METAL SCREW HEX
More informationINSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET
HIGH EDGE 2 1/4"(57mm) 03079400070 INSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET IMPORTANT: THIS LOCK IS NON-HANDED. LOCK IS FACTORY PACKED PREADJUSTED FOR 1³ ₄" (45mm)
More informationPleated Shades with Corded Top Down / Bottom Up Option
Pleated Shades with Corded Top Down / Bottom Up Option Installation Instructions Email: customerservice@blindster.com Call us: (888) 256-8672 Mon - Fri 8am - 7pm (CT) Congratulations on purchasing Pleated
More informationSTEP 1 - CEILING PREPARATION
STEP 1 - PREPARATION 1/4-20 THREADED RODS SR FIXTURE SLOT/ IN SHEET ROCK WHIP A) MAKE SLOT IN SHEET ROCK ACCORDING TO RUN INFORMATION, TYPE OF FIXTURE AND REFER TO S REQUIRED (FIGURE 2 - SR* AND FIGURE
More information" BASE CABINET
INSTALLATION GUIDE INSTALLATION GUIDE Before You Begin Installing Your Kitchen Cabinets 1. Read through installation guide to understand all steps and gather tools needed. 2. Verify that all of the hardware,
More informationINSTALLATION INSTRUCTIONS
HONEYCOMB & PLEATED Lift & Lock Cordless Lift Systems Standard Top Down/ Bottom Up INSTALLATION INSTRUCTIONS Revised 8/2018 Getting Started A few simple tools are required: - Measuring tape - Carpenters
More informationInstallation Instructions Standalone or continuous run configurations - 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS
- 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS TruGroove Drywall A3 MOUNTING Ceiling INSTALLATION System Overview These instructions review how to install trimless drywall versions of TruGroove
More informationSMARTfit Functional and Brain Fitness Training Multi-Station Trainer Installation for Stud and Concrete Walls (US)
SMARTfit Functional and Brain Fitness Training Multi-Station Trainer Installation for Stud and Concrete Walls (US) 2017 SMARTfit, Inc. www.smartfitinc.com 1 Unlike other fitness equipment which may require
More information5 ACCESS PANEL INSTALLATION SPACER *SLIDE TO LOCATION OF FASTENER DURING INSTALLATION OF EACH FASTENER
1/2 K.O. (3/8 K.O. on 165 with factory supplied 3/8 flex conduit fitting) TR - Trim Flange Side Blocking Install Method Secure fixture to structure following instructions below: 1. Remove lens and internal
More informationRound or Square Type IC Down Light Housing with LED Lamp for Flangeless Trims E3_L_-L_DI 1.4
Installation Instructions for 90ELED-DIC Round or Square Type IC Down Light Housing with LED Lamp for Flangeless Trims E_L_-L_DI. LED - ROUND/ SQUARE FLANGELESS GENERAL PRODUCT I NFORMATION: This product
More informationExtra Wide Heavy Duty Plastic Lockers Series Locker Installation Instructions
Locker Installation Instructions Thank you for selecting Extra Wide Heavy Duty Plastic Lockers. We are confident that the quality and construction of the lockers will prove to be a good investment. These
More informationINSTALLATION AND CARE INSTRUCTIONS
INSTALLATION AND CARE INSTRUCTIONS Vertical Applications Honeycomb Shades 52 C8-10-3401 Rev 2/14 CONTENTS Introduction...2 Before You Begin...3 Vertical Application Parts Overview...4 Materials Required...5
More informationSimply lift up on the flexible cover to remove it from the radiator support panel and factory grille, exposing the upper mounting hardware.
2 Simply lift up on the flexible cover to remove it from the radiator support panel and factory grille, exposing the upper mounting hardware. Apply masking tape to the top of the bumper cover underneath
More informationInstallation Operation Care
Installation Operation Care Provenance Woven Wood Shades Standard Cordlock CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3 Mount the
More informationCabinet Mount Lifter Instructions
PART LIST 2 @ Side Pivot Arms 1 @ Coupler Tube 1 @ Left Hand Bracket 1 @ Right Hand Bracket 2 @ Cover Support Arms w/ Foam Grip 1 set of Cover Saver 4 @ 4 Wood Screw 8 @ 1 Wood Screw 12 @ 1 Black Tek Screw
More information- 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS. Factory pre-installed mud flange TOOLS REQUIRED: Phillips screwdriver, 5/16 nut driver.
- 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS TruGroove Drywall A3 MOUNTING Ceiling INSTALLATION System Overview These instructions review how to install drywall trim versions of TruGroove recessed
More informationPreference Collection 5580 Treatment Console INSTALLATION GUIDE
Preference Collection 5580 Treatment Console INSTALLATION GUIDE 0 WARNING Failure to install the 5580 as described in this installation guide may cause the unit to collapse, resulting in serious injury
More information