END FEED INSTALLATION
|
|
- Elfreda Patrick
- 5 years ago
- Views:
Transcription
1 STARLINE PLUG-IN RACEWAY END FEED INSTALLATION The Universal End Feed (product numbers beginning with URPF, URDF, or MRPF, MRDF) provides the installer a provision to connect supply power to the Plug-In Raceway system without the use of a junction box. WARNING: MAKE SURE POWER IS OFF BEFORE MAKING ANY WIRE CONNECTIONS 17 in. (432mm) Cover Piece Ground Wire 12 in. (305mm) End Feed Housing Bus Connector End Feed Wires (Color Coded) w/ Wire Clips Phase colors are as follows: Phase A: Black Phase B: Red Phase C: Blue End Cap End Cap Clip Bus Connector Keeper Joint Insulator (can be installed on either end of housing) *Contractor to connect incoming power to End Feed Wires using provided terminal lugs and shrink tubing (not shown)
2 1. Locate the End Feed housing where you want to install the end feed to attach incoming power. Raceway End Feed Housing Raceway Straight (can be installed before end feed) Ensure notch is facing down before installing 2. Secure the joint insulator to the End Feed housing by removing the cover of the double-sided tape attached to the back of the joint insulator. Install the joint insulator so that the edge is flush with the end of the end feed section. Remove cover of double sided tape
3 Raceway End Feed Housing Raceway Straight Install joint insulator here for incoming power from the LEFT Install joint insulator here for incoming power from the RIGHT Align joint insulator with step in housing (use joint insulator arrows as guides) 3. Secure the end feed housing to the surface using wall mounting clips (Cat No. SRPWMC-PIR or SRDWMC-PIR) OR drilling through the end feed housing at the scoring lines for guidance. Use the following screws for: a. Drywall: use self-drilling drywall anchors with #8x1-1/2 [4mm Dia x 40mm Length] flat head wood screw) b. Concrete: use (3/16x1-3/4 [4.8mm Dia x 45mm Length] tapcon flat head screw).
4 4. To install conduit so to connect power to the raceway end feed, drill the required size hole through the end cap, then install the conduit fitting in the end cap. (Parts provided by customer) Drill the appropriate size hole End Cap Supplied by customer 5. Install the End Cap clip into the channel along the raceway backplane (the deeper channel). Secure the end cap to the end feed housing by mounting the provided screw into the installed End Cap Clip. End Cap Clip Provided Screw
5 6. Now that the direction of the end feed unit has been established, the color-coded wires may now be inserted into the bus connector. Bus Connector Finished End Feed Connector Body 7. Insert the bus connector over the joint insulator and center it on the seam, or joint. Secure the loose end feed wires to one side of the terminal blocks. Connect and torque wires to 25 inch/lbs. to terminal blocks Bus Connector - Center over the end of the housing For customer power connection to terminal blocks, see Torque Reference Chart (last page)
6 8. To make the electrical connection from the end feed kit to the 1 st raceway straight, follow these steps: a) Slide the bus connector keeper up the 1 st raceway straight to be used adjacent to the end feed kit. b) Now slide the bus connector keeper over the bus connector such that the indicator hole is lined up at the section joint. c) Once the bus connector keeper is in position, turn the chase nipples to lock the connector body in place. After the chase nipples are tightened, use an allen wrench to tighten the four set screws against the backplane. (a) Raceway straight (b) (a) Slide Bus Connector Keeper up the raceway straight 1 st (b) Then slide over bus connector Chase nipple torque to 10 Inch/lbs. Indicator hole Handtight set screws
7 9. Field wiring connection can be made inside the end feed section. Field wires are pulled though the conduit to meet with the color coded end feed wire leads. Connections are made using the terminal blocks and shrink tubing provided. 10. A separate ground lead is provided with the end feed kit, and may be used as necessary. (Drill a diameter hole in the back plane, use the #8-32x.375 self-tapping screw and ring lug for ground). 11. Once the wiring connections are complete, snap the cover back onto the end feed housing. Note: Alternative conduit entrances can be made through the top, bottom or back of the end feed section. Drilling modifications (not shown here) can be made in the field.
8
EP-60 END OF CAR JUNCTION BOX KIT and ASSEMBLY AND INSTALLATION INSTRUCTIONS
EP-60 END OF CAR JUNCTION BOX KIT 786282 and 786438 ASSEMBLY AND INSTALLATION INSTRUCTIONS Figure 1 EP-60 End of Car Junction Box Kit Item No. Qty. Description P/N Kit No. 786282 Kit No. 786438 1 2 Screw,
More informationMotorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions
Motorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions Tools Needed Drill 3/8 Metal Drill Bit ¼ Masonry Drill Bit Measuring Tape Pencil 4 Level Phillips
More informationJ-BOX. 3-O or 4-0 MUD RING J-BOX BRACKET BAR CABLE GRIPPER/ CANOPY MOUNTING STUD 8-32 BRACKET BAR SCREWS CANOPY STRAIN RELIEF POWER CORD CANOPY
KELSEY - CSS Cable Suspended Rotational and Static CSS - Cable Suspended 3-O or 4-0 MUD RING BRACKET BAR 1/4-20 STUD 8-32 BRACKET BAR SCREWS STRAIN RELIEF POWER CORD MOUNTING GRIPPER AIRCRAFT CABLE CABLE
More informationFigure A. Figure B. Figure C. Figure D
Xsite 1 Power/Data Tile and Components Tools Required Tape Measure Cordless Drill/Driver #2 Phillips Screw driver bit Rubber Mallet Flat Blade Screwdriver Figure A Hardware Required Provided as shown Installation
More informationRugged Ridge 2 Receiver Hitch Kit (J21068)
Rugged Ridge 2 Receiver Hitch Kit (J21068) Installation Time: 1-2 Hours Tools Required: ¾ Open End Wrench 18 mm Socket ¼ drive Pliers/Needle nose pliers/channel locks, etc. Torque wrench Phillips head
More informationCalf-Tel Pen System Assembly Instructions
Calf-Tel Pen System Assembly Instructions (Instructions work for 4, 6, and the 7 Pen Systems) 1 ASSEMBLY OF PEN FRONT AND WALLS START THE ASSEMBLY BY LINING UP THE TWO UNI-DIRECTIONAL ARROWS IN THE TOP,
More informationED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS
ED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS Ver.2 1300 SERIES CONCEALED VERTICAL ROD DEVICE Top Strike Latch Screws Strike Screws Release Plunger Top Latch Plunger Screws
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationPhone: Installation Instructions
Installation Instructions Multi-Function Step Light GEMINI 3000 SERIES _V1.1 The following instructions are general guidelines. Installation should be performed by a qualified electrician in accordance
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationINDIVIDUAL MOUNTING: T-Bar
X1 (T-BAR) INSTALLATION INSTRUCTIONS GENERAL NOTES NOTE : Additional support to structural member may be required. Check with local building codes for requirement. 1. Place troffer clamp approx. 6 from
More informationMultiples EM_ 1.4. Install 1X1/1X2/1X3/1X4 Housings. Installation Instructions for. This product is suitable for indoor locations.
Installation Instructions for 90EMULTI Multiples EM_. GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations. This product can be dimmed with a standard electronic dimmer or a 0-0V
More informationYardistry. External Display YP *Time required for assembly approximately 1.5-2hrs
Yardistry External Display YP40030 *Time required for assembly approximately 1.5-2hrs Components 4 Packages of Panel Clips (Includes 6 Panel Clips and Hardware) 3 16 1/2 x 16 1/2 Signs (hardware Included)
More informationInstall the Housing. Installation Instructions for Entra Round or Square Type IC, Air-tight New Construction Adjustable LED Housing EN3_-LH9_ 1.
Installation Instructions for Entra Round or Square Type IC, Air-tight New Construction Adjustable LED Housing 90ENTRA EN_-LH9_. LED - ROUND/ SQUARE GENERAL PRODUCT I NFORMATION: This product is safety
More informationHow to Install Custom Real Wood and Faux Wood Blinds
Before you begin your installation: READ ALL INSTALLATION INSTRUCTIONS! Make sure that you have all tools and hardware needed for installation. Check the installation surface (wall, ceiling, or window
More informationAssembly Instructions
InTandem Table System November 20 InTandem Table System - Worksurface #4 x/" 4 wood screw power beam Tools Provided T-0 Extended Torx Driver T-25 Torx Driver Additional Tools Required Soft protective
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS TM X-10 Type 1F HIGH SECURITY ELECTRONIC LOCK Table of Contents Introduction... 1 Basic Tools and Materials Needed... 1 Lock Parts for Installation... 1 Installation Kit Contents...
More informationReady To Go SimpleSpec tm. Installation Manual. For more information, please visit 3-form.com or call
Contents Overview ( 1) 3/8" Varia Panel = Cable Tensioner with Cover Plate KIT Stainless Steel: 3-15-1636-K Black Oxide: 3-15-2005-K Cable Tensioner with Cover Plate SS: 3-15-1636 BO: 3-15-2005 + M8 Thread
More informationx2 1/4 (6mm) Floor Anchor
INSTALLATION GUIDE Main Components x1 Rail x5 Wall Spacer x2 Anti-jump Block x2 Straight Strap x1 Right Stopper x1 Left Stopper x5 5/16 (8mm x 60mm) Carriage Bolt x5 5/16 (8mm x25mm) Anchor x5 5/16 (8mm
More informationLine volt rail & fixtures. Low volt quick connect fixtures with transformers
INSTRUCTIONS: Line Volt Flexrail2 Safety Instructions: A qualified electrician must install system only. System is intended for installation in accordance with National Electric Code, local and Federal
More informationKeypad Lock Retrofit Kit for Follett REF Undercounter Refrigerator P/N
Materials supplied Reference # Keypad assembly (housing and mounting base) 1 Keypad housing base 2 Lock mechanism with cable 3 (9) 8-32 x 1/2" stainless steel screws 4 Latch 5 Jig 2, latch 6 Jig 1, keypad
More informationInstallation Instructions. Oakmont Folding Doors
Before You Start For quick and easy installation of your Oakmont folding door, read these instructions thoroughly. A few minutes of prior planning will make the job easier and ensure years of trouble-free
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationInstallation Instruction
Tools Needed for Assembly Stud finder (for wood stud wall) Pencil Mark Electric drill Wood Stud Wall Installation Step 1. Locate the Wood Studs Installation Instruction Drill bit (for wood stud wall) Masonry
More informationinstallation guide ICON classic benching
installation guide ICON classic benching Index ICON Installation Guide Single Run Frame Assembly... Worksurfaces and Electrical... Attaching Worksurfaces to Frame...6 Installing optional accessories...7
More informationMount to the Wall INSTALLATION MANUAL
Mount to the Wall 15 Locate the Wooden Studs This step applies to wooden stud wall installation only. Determine and mark the exact locations of two stud centers on the wall. Wooden studs should be spaced
More informationTIP FOR GETTING STARTED
Tip for getting started TIP FOR GETTING STARTED Be careful not to drill into any electrical wires, ductwork, plumbing or other damagable components. If you have any questions on the locations of these
More informationAssembly and Installation Guide
The Easy Hang Closet Solution SM Install Your elfa In An Instant. Enjoy The Benefits For A Lifetime. Basic Tools For elfa Assembly and Installation Level Hand or Power Drill Drill Bits 1/8", 3/8", 5/16"
More informationHO4 Surface Mount Installation Instructions Overview
Overview Step 4 Mounting to Structure Pages 5-6 Step 5 Joining Luminaires Pages 7-8 Step 1 Mounting Types & Locations Page 2 Step 6 Closing Luminaires Page 9 Helpful Video 0-10V Dimming Step 2 Identification
More informationMFJ-2982 Feather-Lite 80-6 Meter Vertical Antenna
MFJ-2982 Feather-Lite 80-6 Meter Vertical Introduction: The MFJ-2982 is a lightweight 31-foot fiberglass antenna designed to mount on any convenient post, mast, or a suitable wide-stance tripod such as
More informationSliding Door Kit
YOU MUST READ THIS DOCUMENT BEFORE YOU BEGIN TO ASSEMBLE THE DOOR KIT. Thank you for purchasing this GrowSpan door kit. When properly assembled and maintained, this product will provide years of reliable
More informationINSTALLATION INSTRUCTIONS VENETIAN 84" SLIDING SHOWER DOOR SYSTEM (180º INSTALLATION)
INSTALLATION INSTRUCTIONS VENETIAN 84" SLIDING SHOWER DO SYSTEM (180º INSTALLATION) 28539 Industry Drive, Valencia, CA 91355 Toll Free Phone: (877) 728-3874 Toll Free Fax: (888) 440-9567 Phone: (661) 775-1675
More informationMOTORIZED STANDARD SHADE WITH CABLES Installation Instructions
Tools Needed Drill Measuring Tape Pencil 2 Level Plumb Line ¼ Masonry Drill Bit Hammer Linesmans Pliers Cable Cutters Phillips & Flat-Head Screw Driver 11/32 Socket or Open End Wrench 5/32 Allen Wrench
More informationASSEMBLY INSTRUCTIONS. enook Pro
ASSEMBLY INSTRUCTIONS enook Pro Product enook Pro for Monitors, 36w Part# EPM3616zz/xx Anthro Corporation 10450 SW Manhasset Dr. Tualatin, OR 97062 Toll-free: 800.325.3841 Fax: 800.325.0045 email: sales@anthro.com
More informationDublin Stalls Installation Instructions
Dublin Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 9/13/17 Part Identification Round Track Bracket (4) (Not Painted) Round
More informationModular & Hardwired Hub Assembly to "X" and "Y" Posts
Modular & Hardwired Hub Assembly to "X" and "Y" Posts Hardware Package T-Nut Data jack bracket #6 x 1/4" plastite trilobular screw 1/4-20 x 3/4" socket head cap screw #6-32 x 1/4" pan head screw #10-32
More informationIMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the
PART # 1608990 STATIC BRIDGE & RETURN MODULE 1. This sheet covers the steps to install a static bridge or return module with the FX no hinged access panel back option to a height adjustable freestanding
More informationNOTE: Top section pole (Q) is packed INSIDE bottom section pole (S)
Form 0905-0 Instructions and Parts List TM- Mini Castle (modified) MARTIN SAFETY SYSTEM NOTES: () A complete system is packed in two boxes post box and house box. House box contains hardware for both post
More informationB B B
Stock with Scorpion Recoil Pad B..0.0 B..0.0 B..0.0 Removable/Adjustable Tactical Cheekrests X Scorpion Recoil Pad Dual Sided QD Attachment Point Six Position Adjustable Stock Slim Line Rear Aluminum Receiver
More informationELEVEN COLLABORATIVE. CONFERENCE TOPS Assembly Instructions
ELEVEN COLLABORATIVE Table of Contents SUPPORT BRACE ASSEMBLY.... 3 TABLE BASE FRAME ASSEMBLY.... 4 LEG ATTACHMENT.... 5 TOP JOINING PLATE ASSEMBLY... 6 TOP CLAMP/TOP SPACER INSTALLATION.... 7 TOP PLACEMENT
More informationParts list continues on Page 2 HOUSE PARTS PACKED IN HOUSE BOX PARTS IN SMALL PLASTIC BAG (HARDWARE) POST PARTS PACKED IN THIS BOX (LARGE PLASTIC BAG)
Form 05-07 Instructions and Parts List MSS- Martin Safety System NOTES: () A complete system is packed in two boxes post box and house box. House box contains hardware for both post and house assembly.
More informationSeries 1500 Aluminum Door Canopy
Series 500 Aluminum Door Canopy with Sidewings It is our recommendation that you read instructions carefully prior to assembly and installation. Series 500 with Sidewings mounting bar (A) top trim (B)
More informationCABLE COVER ORGANIZER KIT USER GUIDE AND INSTALLATION INSTRUCTIONS
CABLE COVER ORGANIZER KIT USER GUIDE AND INSTALLATION INSTRUCTIONS TOPIC PAGE Applications, Specifications, Warnings and Cautions 2 Kit Contents 3 Installation Instructions Painting. 4 Layout Preparation...
More informationTraditional Wall Mounted Potfiller
TOOLS NEEDED FOR INSTALLATION 1/4 hex wrench (provided in installation kit) 3/32 hex wrench (provided in installation kit) Pencil or marker PTFE tape Small level, or carpenters square Power Drill with
More informationPrivacy Wall & Glass Selections Pivot-Hinged Door (For products manufactured after September 14, 2009)
Privacy Wall & Glass Selections Pivot-Hinged Door (For products manufactured after September 14, 2009) 3/16" HEX BIT #2 ACR BIT 3/8" HEX SOCKET Full-Height (No Switch) Transom (No Switch) Full-Height (With
More informationC 0.05" ALLEN WRENCH. Installation Instructions for Cirrus Channel Suspension T1 with 4" Square or Round Canopy. Section One: Adjusting Cable Position
Doc # 90-CST-SQ_0 W. Fullerton Chicago, IL 0 Ph:.0.9 Fax:.9. www.pureedgelighting.com info@pureedgelighting.com 0 PureEdge Lighting. All Rights Reserved. Installation Instructions for Cirrus Channel Suspension
More informationInstallation Instructions for Cirrus Suspension Downlight with Power - End Feed. Section One: 4" Flush Canopy Version
Doc # 0-CSP-E_0 W. Fullerton Chicago, IL 606 Ph:.0. Fax:..6 www.pureedgelighting.com info@pureedgelighting.com 06 PureEdge Lighting. All Rights Reserved. Installation Instructions for Cirrus Suspension
More informationWindload Post 9100/9600/9900 Installation Instructions
Windload Post 9100/9600/9900 Installation Instructions Wayne Dalton, a division of Overhead Door Corporation P.O. Box 67, Mt. Hope, OH 44660 www.wayne-dalton.com Wayne-Dalton Corp. P.O. Box 67 Mt. Hope,
More informationGRANDIO G R E E N H O U S E S CONCRETE ANCHORING KIT FOR GRANDIO SUMMIT FLAT MOUNT BASE KITS CONCRETE ANCHORING KIT PARTS LIST FOR ALL SIZES
GRANDIO G R E E N H O U S E S CONCRETE ANCHORING KIT FOR GRANDIO SUMMIT FLAT MOUNT BASE KITS CONCRETE ANCHORING KIT PARTS LIST FOR ALL SIZES GRAPHIC PART NAME 2X8 2X2 2X6 2X20 2X24 2X28 2X32 TAPCON 44
More informationPAC-12 Kit Contents. Tools Needed Soldering iron Phillips screwdriver Wire stripper Wrenches, 7/16 and 1/2 Terminal crimp tool Pliers Solder
PAC-2 Kit Contents Part Quantity Screws: 8/32 x 3/8 Screws: 8-32 x 5/6 Screw: 8-32 x /4 #8 internal tooth washers #8 solder lug ring terminals Bolt: Aluminum, /4-20 x.5 /4 internal tooth washer Nut: Aluminum
More informationPacific Antenna RF Probe assembly
Pacific Antenna RF Probe assembly Parts In the Kit: 1 1/2 x 3 Blue PEX tube 2 5/8 O.D. vinyl caps 2 3/32 dia x 2 brass tube sections 2 Pogo spring contacts 1 4-40 x 7/16 pan head screw 1 4-40 x 1/4 pan
More informationMAG-CONV Basic, 48, 48R & Midline Front Mount
Parts Required: Tools Used: Mag Wheels Brakes Brake Rods Mounting Bracket Anti Tippers 7/16" Wrench Screw Driver Rubber Mallet 5/8 Wrench 5mm Allen Wrench Step Execution Figures 1 Remove front 5" total
More informationAluminum Railing Gate Kit
BOM-34115787 Aluminum Railing Gate Kit INSTALLATION INSTRUCTIONS Read all instructions prior to installing product. Refer to manufacturers safety instructions when operating any tools. To register your
More informationASSEMBLY AND CARE INSTRUCTIONS JUST FOR KIDS 355
ASSEMBLY AND CARE INSTRUCTIONS VERSION: 8920100 (Revised 06/16) JUST FOR KIDS 355 SALES AND SERVICE spiethamerica.com Canada and International 135 Forestview Road, PO Box 40 Orillia, Ontario, Canada L3V
More informationFace Mount to Through-the-Post Mount
Face Mount to Through-the- Mount Cable Runs through Two Corners When going around two corners, it s necessary to tension the cable from both ends as shown in Deck 4. Use the 672 series The tensioning devices
More informationcompile system INSTALLATION GUIDE Updated January 2019
INSTALLATION GUIDE Updated January 09 compile system Table of Contents Panels 0 Quick Connect Clips 0 Lock Clips 0 Panel Trims 0 Privacy Glass 0 Post Base Covers 04 Electrical 04 Power Distribution Harness
More informationCONTENTS TOOL LIST U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS. Revised: June 2013
U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS TOOL LIST Required Tools: - Reciprocating Saw with Metal Cutting Blade - Drill - 7/16 Drill Bit for Metal Drilling -
More informationClearSpan PolyMax Windbreak Wall
ClearSpan PolyMax Windbreak Wall Photo may show a different but similar model. 2007 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. Revision date: April 2007ldg STK# DIMENSIONS
More informationMedia Storage Systems Fixed Media Cabinets
Owner s Manual Media Storage Systems Fixed Media Cabinets Contents 1-Column Fixed Media Storage Cabinet Important User Information...........................2 Safety Precautions.................................3
More informationTorqueMaster Replacement Spring
TorqueMaster Replacement Spring Installation Instructions NOTE: Use these installation instructions in conjunction with the TorqueMaster Repair / Replacement Spring Program literature. Copyright 999 Wayne-Dalton
More informationSeries 1100 Aluminum Door Canopy
Series 00 Aluminum Door Canopy with Support Arms It is our recommendation that you read instructions carefully prior to assembly and installation. Series 00 with Support Arms MOUNTING BAR (A) TOP TRIM
More informationPro-Doweling Kit USER S MANUAL #840. Visit us at
Pro-Doweling Kit USER S MANUAL #840 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Please read this manual carefully and thoroughly
More informationInstallation and Assembly: Flat Panel Pull-out Swivel Wall Mount
Installation and ssembly: Flat Panel Pull-out Swivel Wall Mount Models: SP850-V2X2 2300 White Oak Circle urora, Il 60502 (800) 865-2112 Fax: (800) 359-6500 www.peerlessmounts.com ISSUED: 01-17-12 SHEET
More informationHOUSE PARTS PACKED IN HOUSE BOX PARTS IN PLASTIC BAG (HARDWARE) PARTS IN SMALL PLASTIC BAG (FLOOR CLIPS) PARTS PACKED IN BUNDLE
Check parts against this list before starting assembly. Refer to illustrations on pages 6 and 7 to view house parts. If any shortages are found, refer to Packing Slip for claim instructions. Item 3 5 6
More informationINSTALLATION INSTRUCTIONS
PARTS LIST ITEM PART DESCRIPTION QTY 73-A 503F 9MM 50G 5A 50E 505S 50H Connector Bracket Door Stops Support Bar Panel Glass Bracket Wall Mount Bracket Rollers Center Guide Recessed Finger Pull Fixed Panel
More informationAssembly InstructIons
tp50 FLAT PANEL TV MOUNTING SYSTEM OPTION OPTION 2 OPTION 3 Flat Panel TV Stand Stand with TV Mounting System Stand with Wall Mount Assembly InstructIons for your safety, please follow these precautions:!
More informationflat panel solutions Specifications Box contents Warnings CAUTION: Tilt Wall Mount for LCD, Plasma, and LED Displays Instruction Manual
flat panel solutions Tilt Wall Mount for LCD, Plasma, and LED Displays Instruction Manual MST65BKR Fits TVs 37-65 Maximum Load Capacity 165 lb (75kg) Specifications Display Size: 37 to 65 Maximum Load:
More information1 Intro Folding Panel System 12 Panel Display Backwall Set-up Instructions 1. 2.
1 Intro Folding Panel System 12 Panel Display Backwall Set-up Instructions Right Stack top panels on bottom panels Unfold display wall Set in desired configuration Wrong Pull from here Remove each folded
More informationInde-Pendants Family. 32L Ring Plaster Trim, Grid and Drywall Ceiling Types. Document No Installation instructions for 32L-Rxx-P
Inde-Pendants Family 32L Ring Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-Rxx-P Document No. Supplied by Litecontrol 32L Inde-Pendants: Ring (Plaster Trim, Grid and Drywall
More informationParts Included: Tools Required: Canvas Office Landscape Interiors Off Module 90 Connector Kit Installation and Disassembly for Recycling Instructions
Y Parts Included: Canvas Office Landscape Interiors Off Module 90 Connector Kit Installation and Disassembly for Recycling Instructions FT127.A N Shim A Light Seal B Foam Light Seal C G H Double-Face Tape
More informationDeck Mount Installation with Bench
Deck Mount Installation with Bench 1. Mark track with square. 2. Cut tracks with saw. 3. Drill ¼ hole (if needed.) 4. Countersink track. 5. Countersink all track 6. File all track ends. ends. 7. Lay out
More informationCustomer Notice: Congratulations again on your SawStop purchase, and thank you! -SawStop Tualatin, OR
Customer Notice: Congratulations on the purchase of this Sliding Crosscut Attachment. As the owner of a SawStop saw, you are familiar with our high standards for quality, fit and finish. Different from
More informationLeafy Greens Spinner Construction Manual
Leafy Greens Spinner Construction Manual University of Houston Conrad N. Hilton College Food Science Lab Materials list: Base and Armature Approximately 8-1 PVC cut into sections o 3-22.5 o 2-7 o 2-4 o
More informationBARN DOOR HARDWARE KIT
INSTALLATION GUIDE Main Components x1 Rail x5 Wall Spacer x2 Anti-jump Block x2 Bent Strap x1 Right Stopper x1 Left Stopper x5 5/16 (8mm x 60mm) Carriage Bolt x5 5/16 (8mm x25mm) Anchor x5 5/16 (8mm x
More informationInstallation Instructions for DIY or Completed 45 Degree Light Channel
201 Edge Lighting. All Rights Reserved. Installation Instructions for DIY or Completed Degree Light Channel IMPORTANT INFORMATION - This instruction shows a typical installation. 11 W. Fullerton Ave Chicago,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLine Series 1180 DuraLine Series Class-A Fire Rated IMPORTANT: Review these instructions thoroughly prior to installation. FLOOR ANCHORED
More informationINSTRUCTIONS TS93 GSR PT RIGHT HAND ACTIVE LEFT HAND INACTIVE RIGHT HAND INACTIVE LEFT HAND ACTIVE
INSTRUCTIONS ATTENTION!!! Before you begin, determine installation type (RIGHT HAND ACTIVE OR INACTIVE). Door coordinator suitable for door from 59 to 98 in width. Inactive door width in the case of unequal
More informationDRYWALL CEILING SPLINE KICKER REFLECTOR DIFFUSER LENGTH TABLE DIFFUSER LENGTH TABLE DESCRIPTION 2' IND 3' IND 4' IND 6' IND 8' IND
SUPPLEMENTAL INSTALLATION TYPE LG-WWD-44, R-WWD-44 & RP-WWD-44 510553-2000 WHICH IS CONTRARY TO THE CONTAINED HEREIN. P/C PG. 1 OF 1 1/4-20 THREADED ROD OR EQUAL SUPPLIED PANHEAD SHEET METAL SCREW HEX
More informationInstallation and Assembly: Flat Video Wall Mount For 40" to 65" Flat Panel Displays
Installation and Assembly: Flat Video Wall Mount For 40" to 65" Flat Panel Displays Model: DS-VW665 Maximum Load Capacity: 125 lb (57 kg) 1 of 11 ISSUED: 03-22-12 SHEET #: 125-9288-4 06-25-13 NOTE: Read
More informationInstallation Instructions
Important 1. Acclimate materials 24 hrs before installation. Maintain temperature controlled environment after installation 2. Install in accordance with manufacturer s installation instructions. Failure
More informationNX7 SERIES 5-1/2 HANDRAIL
STORAGE & HANDLING The handrails are shipped unassembled. Upon receipt, immediately check all material for any damage that may have occurred in transit and verify that all of the items and quantities are
More informationMirage Installation Manual
Mirage Installation Manual General Information This installation manual provides necessary information for the safe installation of the Mirage product. WARNING: Failure to follow the instructions in this
More informationWARNING. BX Ford Explorer With Adaptive Cruise Control & Eco Boost Installation Instructions
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More informationOxford Stalls Installation Instructions
Oxford Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 8/15/17 Before You Start Typical stall sizes are 10 x 10, 12 x 12 or
More informationA SRF/SERF A SRF/SERF
A1100-055SRF/SERF A1100-056SRF/SERF Remote Fill Assembly INSTALLATION INSTRUCTIONS **CRITICAL - MUST READ** This unit can only be used for new installations or tank level retrofits that allow access to
More informationHQ Pole Upgrade Kit for HQ Adjustable Table and HQ QuilTable Assembly Instructions 1
HQ Pole Upgrade Kit for HQ Adjustable Table and HQ QuilTable Assembly Instructions QF09775 The pole upgrade kit can be used with or without the QF09700 HQ Precison-Glide track upgrade kit. What s Included
More informationSMARTfit Functional and Brain Fitness Training Multi-Station Trainer Installation for Stud and Concrete Walls (US)
SMARTfit Functional and Brain Fitness Training Multi-Station Trainer Installation for Stud and Concrete Walls (US) 2017 SMARTfit, Inc. www.smartfitinc.com 1 Unlike other fitness equipment which may require
More informationcampfire big lamp Assembly Instructions
campfire big lamp Assembly Instructions tools needed Here's what's in the box BOX #3 For assembly videos go to myturnstone.com/campfire/instructions BOX #1 Base (1) assembly time needed video X screw (4)
More informationThe Astronomical League
The Astronomical League www.astroleague.org Library Telescope Modifications Check the collimation with the eyepiece cap provided (the one with the hole in its center) before starting on any modifications.
More informationFABA. Installation Instructions. Conductor Bar System. Publication #FABA-03 3/1/04 Part Number: Copyright 2004 Electromotive Systems
FABA Conductor Bar System Installation Instructions Publication #FABA-03 3/1/04 Part Number: 005-1062 Copyright 2004 Electromotive Systems 1S 100 Z Installation Instructions Contents: Basic Diagram - -
More informationShetland Stalls Installation Instructions
Shetland Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 1/9/18 Before you start Kit can accommodate up to 12 wide stall front
More informationImportant Loading Information. Tools Required. Meridian Lateral Files Instructions
Y Meridian Lateral Files Instructions! WARNING Failure to observe stated capacities below will result in unsafe usage conditions, causing possible product damage or personal injury. Important Loading Information
More informationSliding Crosscut Table installation guide
Sliding Crosscut Table installation guide model tsa-sa48 A Note About Color Variations Among Anodized Aluminum Components Congratulations on the purchase of this SawStop Sliding Crosscut Table. We at SawStop
More informationPrivacy Wall Glass Selections - Polished Edge Slider Door
Privacy Wall Glass Selections - Polished Edge Slider Door 3/6" HEX BIT PUTTY KNIFE #2 ACR BIT SUCTION CUP HOLDERS DOOR LEAF: Satin Tempered Clear Tempered LOCTITE 425 SIDE LIGHT ETCHED GLASS STYLES: Satin
More informationSales & Service. JFK - Just For Kids. sasportonline.com. 135 Forestview Road 7879 Will Rogers Blvd.
Sales & Service sasportonline.com SA Sport (Canada) SA Sport (U.S.A.) 135 Forestview Road 7879 Will Rogers Blvd. P.O. Box 40 Fort Worth, Texas Orillia, Ontario USA 76140 Canada L3V 6H9 Telephone: (705)
More informationFIRST TEAM SPORTS, INC.
FIRST TEAM SPORTS, INC. INVADER EZ-CRANK PORTABLE BASKETBALL GOAL ASSEMBLY INSTRUCTIONS Revised - 08/04/10 BILL OF MATERIALS (1) BASE TANK (1) BACKBOARD MOUNT (2) 5/16 X ¾ HEX BOLT (1) LOWER POST (2) SPRING
More informationTM12 ASSEMBLY INSTRUCTIONS
TM12 ASSEMBLY INSTRUCTIONS Congratulations on purchasing the finest purple martin house available. Nature House Brand houses are the proven leader in aluminum martin housing for over half a century. After
More informationTools Needed Hardware Provided (per shade) Hardware Needed
Baby Grande or Grande Motorized (XQ5 Premium) Shade with Cables and Housing Installation Instructions Tools Needed Hardware Provided (per shade) Hardware Needed Drill 3/8 Metal Drill Bit Measuring Tape
More informationSECTION 7. SAFETYING
9/8/98 AC 43.13-1B SECTION 7. SAFETYING 7-122. GENERAL. The word safetying is a term universally used in the aircraft industry. Briefly, safetying is defined as: Securing by various means any nut, bolt,
More informationInstallation and Assembly: Flat \ Tilt Wall Mount for VESA 400x400
Installation and ssembly: Flat \ Tilt Wall Mount for VES 400x400 Model: T642-003 Max Load Capacity: 100 lb (45.4 kg) 3215 W. North ve. Melrose Park, IL 60160 (800) 729-0307 or (708) 865-8870 Fax: (708)
More information