S-DECK PANEL INSTALLATION DETAILS BERRIDGE MANUFACTURING COMPANY

Transcription

1 S-DECK PANEL INSTALLATION DETAILS MANUACTURING

2 INDEX INDEX INSTALLATION INSTRUCTION INSTALLATION INSTRUCTION INSTALLATION INSTRUCTION INSTALLATION INSTRUCTION INTRODUCTION TO TYPICAL DETAILS OVERVIEW S-DECK SYSTEM EAVE DETAIL; EAVE DETAIL; OPEN RAMING EAVE DETAIL; W/S-DECK WALL PANEL; HIP RIDGE; SHED ROO RIDGE HIP RIDGE; OPEN RAMING RIDGE; TERMINATION AT DORMER VALLEY GABLE GABLE; WITH S-DECK WALL PANEL GABLE; WITH WALL PANEL GABLE; CURVED S-DECK HEAD WALL; WITH PARAPET HEAD WALL; WITH S-DECK HEAD WALL; WITH REGLET RAKE WALL; WITH WALL PANEL RAKE WALL; WITH S-DECK WALL PANEL RAKE WALL; WITH REGLET RAKE WALL; WITH PARAPET RAKE WALL; OPEN RAMING; S-DECK WALL PANEL RAKE WALL; CURVED S-DECK; WITH WALL PANEL SLOPE TRANSITION WITH LASHING VALLEY VALLEY; OPEN RAMING ROO PENETRATION; PIPE PENETRATION SD-0 SD-1 SDI-1 SDI-2 SDI-3 SDI-4 SD-2 SD-3 SD-10 SD-11 SD-12 SD-20 SD-21 SD-22 SD-23 SD-30 SD-31 SD-32 SD-33 SD-40 SD-41 SD-42 SD-50 SD-51 SD-52 SD-53 SD-54 SD-55 SD-60 SD-70 SD-71 SD-80 MANUACTURING INDEX PAGE/ILE SD-0

3 ROO PENETRATION; SQUARE (PLAN VIEW) ROO PENETRATION; SIDE A ROO PENETRATION; SIDE B ROO PENETRATION; SIDE C ROO PENETRATION; LARGER THAN 4"; OPEN RAMING INSIDE CORNER; OUTSIDE CORNER; INSIDE CORNER; OPEN RAMING OUTSIDE CORNER; OPEN RAMING INSIDE CORNER; ; HORIZONTAL OUTSIDE CORNER; ; HORIZONTAL HEAD DETAIL; SLAB DETAIL; SILL DETAIL; JAMB DETAIL; SD-81 SD-82 SD-83 SD-84 SD-85 SD-90 SD-91 SD-92 SD-93 SD-94 SD-95 SD-96 SD-97 SD-98 SD-99 MANUACTURING INDEX PAGE/ILE SD-1

4 A. S-DECK PANEL: THE S-DECK PANEL IS ACTORY ABRICATED TO A CONSTANT CORRUGATION DEPTH O 7/8" AND A NOMINAL PANEL COVERAGE O 32" OR ". PANEL MAY BE ORDERED ROM THE ACTORY STRAIGHT OR CURVED (MINIMUM RADIUS 5'-0"). USED ICE AND WATERSHIELD AS UNDERLAYMENT UNDER CURVED ROO. PANELS ARE ABRICATED TO A MINIMUM LENGTH O 5'-0" AND A MAXIMUM LENGTH O 40'-0". B. C. MINIMUM SLOPE: THE S-DECK PANEL IS RECOMMENDED OR ROO SLOPES O 3 ON 12 OR GREATER. SLOPES LESS CONSULT MANUACTURING. MATERIAL STORAGE: CAUTION MUST BE EXERCISED IN STORAGE O MATERIAL PRIOR TO INSTALLATION. KEEP ALL PREINISHED MATERIAL IN A DRY LOCATION WITH ADEQUATE VENTILATION AND OUT O DIRECT SUNLIGHT. EXPOSURE TO DIRECT SUNLIGHT AND/OR MOISTURE MAY CAUSE THE ACTORY APPLIED STRIPPABLE PLASTIC ILM TO ADHERE TO THE METAL PERMANENTLY AND DISCOLOR THE INISH. I THIS SHOULD OCCUR THE PAINT WARRANTY WILL BE VOID. D. E. STRIPPABLE ILM: THE STRIPPABLE PLASTIC ILM, WHICH IS APPLIED OVER MOST PREINISHED PRODUCTS, PANELS, LASHINGS, COILS AND LAT SHEETS, PROVIDES PROTECTION O THE INISH DURING ABRICATION AND TRANSIT. THIS ILM MUST BE REMOVED PRIOR TO INSTALLATION. REQUIREMENTS: MANUACTURING RECOMMENDS THE USE O EITHER 24 GA. CORRUGATED SHEATHING (NOMINAL 2 1/2" PITCH BY 7/8" DEPTH) OR A MINIMUM O 1/2" PLYWOOD SHEATHING TO PROVIDE SUICIENT HOLDING POWER OR ASTENERS. CONTACT MANUACTURINGS ENGINEERING DEPARTMENT OR USE O ANY OTHER TYPE O. (# 30 ELT UNDERLAYMENT OR EQUAL MUST BE USED OVER ANY ). DUE TO # 30 ELTS TENDENCY TO TEAR WHEN USED OVER CORRUGATED DECKING, MANUACTURING RECOMMENDS GRACE ICE AND WATERSHIELD OR EQUAL TO BE USED AS AN UNDERLAYMENT OR ALL CORRUGATED DECKS.. G. SHEATHING INSPECTION: 1. SHEATHING END JOINTS SHOULD BE STAGGERED. 2. ALL END JOINTS SHOULD MEET AT EITHER A JOIST OR RATER. 3. BLOCKING O "H" CLIPS SHOULD BE USED I JOINTS DO NOT REMAIN LAT UNDER THE WEIGHT O WORKMEN. 4. USE SHIMS TO KEEP ENTIRE SUBSTRATE EVEN; UNEVEN SUBSTRATE WILL RESULT IN "OIL-CANNING" IN THE PANELS. SUBSTRATE SHOULD BE LEVEL TO 1/4" IN 20'-0". 5. ALL CUTS AT PENETRATIONS SHOULD BE TIGHT, WITHOUT GAPS. 6. USE WOOD RAMED CRICKETS AT LARGE PENETRATIONS. 7. MAKE SURE SUBSTRATE JOINT ARE TIGHT AT ALL HIPS, VALLEYS AND RIDGES. INSTALLATION OVER OPEN RAMING: REER TO ALLOWABLE UNIORM LOAD TABLE PAGE SD-3. OR DIAPHRAGM CAPABILITIES O "S" DECK CONSULT TECHNICAL DEPT. PURLIN OR OTHER STRUCTURAL BRACING IN THE RESPONSIBILITY O OTHERS. MANUACTURING INSTALLATION INSTRUCTIONS DATE: PAGE/ILE SDI-1

5 H. I. J. OPEN RAMING INSPECTION: 1. PURLINS SHOULD BE ALIGNED WITH TOP LANGES IN THE SAME PLANE TO A TOLERANCE O 1/4" IN 20'-0". UNEVENNESS IN THE TOP PLANE O THE PURLINS WILL RESULT IN ABNORMAL "OIL-CANNING" O PANELS. PURLINS SHALL BE ADEQUATELY BRACED. 2. MANUACTURING RECOMMENDS IN VALLEY AND AROUND ROO PENETRATIONS. DO NOT APPLY PANELS ON OPEN RAMING AT VALLEYS OR ROO PENETRATIONS WITHOUT REERRING TO DETAILS SD-71 AND SD OOT TRAIC IN THE PANELS MUST BE KEPT TO A MINIMUM. ARCHITECTURAL PANELS ARE DESIGNED OR AESTHETICS AND CAN BE EASILY DAMAGED OR DEORMED I EXTREME CARE IS NOT USED. ASCIA/RAKE INSPECTION: 1. STRIKE A LINE THE ULL LENGTH O THE ASCIA OR RAKE. I NOT STRAIGHT, CORRECT WITH SHIMS. 2. MAKE SURE ASCIA/RAKE IS LUSH WITH SHEATHING. ELT UNDERLAYMENT: A SINGLE LAYER O NUMBER THIRTY ELT UNDERLAYMENT (OR EQUAL) MUST BE APPLIED OVER SOLD SHEATHING, AS SHOWN IN THE MANUACTURING TYPICAL ELTING DETAILS. THE USE O ADDITIONAL LAYERS O NUMBER THIRTY ELT IS RECOMMENDED ON LOW SLOPED ROOS, AT ALL VALLEY CONDITIONS, AT ROO PENETRATIONS AND AT CERTAIN OTHER LASHING CONDITIONS AS DEPICTED IN THE S-DECK PANEL TYPICAL DETAILS. GRACE ICE AND WATERSHIELD MAY BE REQUIRED ON LOW SLOPED ROOS OR AT CERTAIN LASHING CONDITIONS. K. L. M. N. ELTING INSTALLATION: 1. DO NOT USE RED ROSIN PAPER UNDER METAL ROOING PANELS. 2. SWEEP ROO AREA CLEAN. 3. USE LAT HEAD GALVANIZED ROOING NAILS 1 1/4" LONG WITH GALVANIZED ELT CAPS. 4. INSTALL VALLEY ELT IRST. 5. INSTALL ELT PARALLEL TO THE EAVE, (2 LAYERS REQUIRED AT EAVE) STARTING AT EAVE AND USING MINIMUM 6" LAPS. USE 2 LAYERS O ELT ON ENTIRE ROO DECK I ROO SLOPE IS 3 ON REER TO ELTING DETAILS WHEN VALLEYS OR ROO PENETRATIONS ARE INVOLVED ON OPEN RAMING CONDITIONS. 7. INSULATE BETWEEN WOOD BLOCKING AND METAL WITH ELT OR GRACE ICE AND WATERSHIELD. 8. USE GRACE ICE AND WATERSHIELD AS UNDERLAYMENT OR CURVED ROOS. 9. VERIY CORRECT METHOD O INSTALLING ICE AND WATERSHIELD WITH ICE AND WATERSHIELD MANUACTURE. ELECTROLYSIS: AVOID ALLOWING LASHINGS AND PANELS TO COME INTO CONTACT WITH EITHER LEAD, COPPER OR OTHER DISSIMILAR METALS AND PREVENT EXPOSURE TO WATER RUNDOWN ROM COPPER AND/OR LEAD. SEALANT RECOMMENDATIONS: TREMCO, INC. SPECTREM 1 SILICONE SEALANT. DO NOT USE CLEAR CAULK. LASHING: I MANUACTURING IS TO SUPPLY LASHING, ALL LASHINGS WILL BE ABRICATED IN 10'-0" LENGTHS WITH SQUARE END CUTS ONLY. THE PURCHASER MUST PROVIDE ALL DIMENSIONS AND DEGREES O ANGLE. MANUACTURING INSTALLATION INSTRUCTIONS PAGE/ILE SDI-2

6 O. P. Q. R. LASHING INSTALLATION: REMOVE STRIPPABLE PLASTIC ILM ROM ALL LASHINGS PRIOR TO INSTALLATION. ALWAYS STAGGER JOINTS WHEN ONE LASHING IS INSTALLED OVER OTHER LASHINGS. INSTALL ALL LASHINGS AS PER TYPICAL DETAILS. ALL LASHINGS ARE TO BE DESIGNED AND INSTALLED TO AVOID TRAPPING WATER. PANELS: MANUACTURING WILL PROVIDE SQUARE END CUTS ONLY ON ALL S-DECK PANELS. COMPUTATION O ALL QUANTITIES AND DIMENSIONS ARE THE RESPONSIBILITY O THE PURCHASER. PANEL INSTALLATION: 1. REMOVE STRIPPABLE PLASTIC ILM ROM EACH PANEL PRIOR TO INSTALLATION. 2. START AT ONE GABLE END O THE ROO AND WORK TOWARD THE OTHER GABLE. 3. EACH PANEL IS TO BE KEPT TIGHT AGAINST THE ADJOINING PANEL. NEVER PERMIT A GAP BETWEEN VERTICAL LAP. ANY CRIMPS OR BENDS MUST BE STRAIGHTENED PRIOR INSTALLATION. 4. KEEP PANELS ALIGNED SO THAT RIBS MATCH AT HIPS, VALLEYS AND WHERE VERTICAL PANELS ADJOIN ROO PANELS. DO NOT INSTALL LONG CONTINUOUS RUNS O PANELS ALL AT ONE TIME WHERE RIB LINES MUST MATCH. INSTALL TEN OR TWELVE PANELS IN ONE ELEVATION AND THEN OLLOW WITH A LIKE NUMBER O PANELS ON THE OTHER ELEVATION. WHEN YOU INSTALL PANELS IN THIS MANNER, YOU WILL BE ABLE TO MAKE ANY ADJUSTMENTS REQUIRED TO INSURE RIB MATCHING. 5. COPPER-COTE, CHAMPAGNE, LEAD-COTE AND PREWEATHERED GALVALUME PANEL INSTALLATION: NOTE THE SERIES O ARROWS PAINTED ON THE UNDERSIDE O THE PANEL. ALL PANELS MUST BE INSTALLED IN A CONSISTENT MANNER, MEANING THAT THE ARROWS ON EVERY PANEL ARE ALL POINTING IN THE SAME DIRECTION. I A PANEL IS REVERSED (ARROWS POINTING OPPOSITE O THOSE ON OTHER PANELS) IT WILL APPEAR, ROM A DISTANCE, A DIERENT SHADE DUE TO THE GRANULAR EECT O THE PIGMENTS IN THE INISH. METALLIC INISHES ARE MATCH- LOT INISHES. DO NOT MIX LOTS. ASTENERS: INSTALL ASTENERS AS PER TYPICAL DETAILS. USE #10 HEX HEAD ZINC PLATED ASTENER WITH METAL BACKED NEOPRENE ASTENER WHEN ASTENING TO WOOD. USE #12 HEX HEAD ZINC PLATED ASTENER WITH A METAL BACKED NEOPRENE WASHER WHEN ASTENING TO METAL * WHEN USING POP RIVETS ON LASHING, STAINLESS STEEL RIVETS ARE RECOMMENDED TO AVOID RUST STAINS. MAKE SURE ALL ASTENERS ARE DRIVEN STRAIGHT AND SET LAT. DO NOT OVER DRIVE ASTENERS AS THIS WILL CAUSE THE CLIP AND/OR LASHINGS TO BUCKLE OR BECOME RECESSED BELOW THE ELEVATION O THE SUBSTRATE. * CONSULT MANUACTURINGS ENGINEERING DEPARTMENT REGARDING ASTENER SPACING TO MEET DESIGN CRITERIA AND THE USE O ANY OTHER TYPE O ASTENER. MANUACTURING INSTALLATION INSTRUCTIONS PAGE/ILE SDI-3

7 MANUACTURING STRIVES TO PROVIDE ITS CUSTOMERS WITH THE HIGHEST QUALITY STRETCHER LEVELED STEEL AVAILABLE. THE LATEST TECHNOLOGY IS ALSO INCORPORATED IN 'S HIGH-PRECISION COIL HANDLING AND ROLL ORMING EQUIPMENT TO MINIMIZE THE STRESS ON METAL DURING PRODUCTION. URTHERMORE, UTILIZES HEAVIER 24 GAUGE METAL RATHER THAN 26 GAUGE STEEL TO LIGHT GAUGE ALUMINUM AS OERED BY MANY COMPETITORS. ALL THESE MEASURES HAVE BEEN TAKEN TO MINIMIZE THE AMOUNT O "OIL0CANNING" (WAVINESS) WHICH IS NATURALLY INHERENT IN LAT SHEET METAL. MANY TIMES, HOWEVER, THE CAUSE O WAVINESS OR "OIL-CANNING" CAN BE TRACED TO UNEVEN SHEATHING, IMPROPER ELT INSTALLATION OR, IN THE CASE O OPEN RAMING, UNEVENNESS O THE TOP PLANE O THE PURLINS OR OOT TRAIC ON THE PANELS. ALL ARCHITECTURAL PANELS REQUIRE CARE IN HANDLING AND INSTALLATION TO AVOID DAMAGING OR DEORMING THE PANELS. THESE INSTALLATION INSTRUCTIONS AND THE OLLOWING TYPICAL DETAILS ARE INTENDED TO PROVIDE OUR CUSTOMERS WITH THE INORMATION REQUIRED OR AN AESTHETICALLY PLEASING AND UNCTIONAL INSTALLATION O THE S-DECK PANEL SYSTEM. NOTE: ALL PRODUCT SPECIICATIONS, DETAIL AND INSTALLATION INSTRUCTIONS SUBJECT TO CHANGE WITHOUT NOTICE. OR SPECIIC PROJECT DETAILS, CONTACT. MANUACTURING INSTALLATION INSTRUCTIONS PAGE/ILE SDI-4

8 THE DETAILS CONTAINED IN THE OLLOWING PAGES ARE MERELY RECOMMENDATIONS AS TO HOW MANUACTURING MATERIALS SHOULD BE INSTALLED. THEY MAY REQUIRE ADAPTATIONS OR MODIICATIONS OR A SPECIIC PROJECT AS CONDITIONS VARY IN BOTH BUILDING DESIGN AND LOCAL WEATHER PECULIARITIES. MANUACTURING SHALL BE HELD HARMLESS ROM ANY AND ALL CLAIMS ARISING ROM LACK O WATERTIGHTNESS AS A RESULT O OLLOWING THESE RECOMMENDED DETAILS. ENSURING WATERTIGHTNESS ON ANY GIVEN PROJECT IS THE UNCTION O THE INSTALLER. THE ARCHITECT/GENERAL CONTRACTOR/INSTALLER MUST ACCEPT THE RESPONSIBILITY TO ADAPT THESE DETAILS TO MEET PARTICULAR BUILDING REQUIREMENTS AND TO ASSURE ADEQUATE WATERTIGHTNESS. THE INSTALLER CAN VIRTUALLY ASSURE WATERTIGHTNESS I THESE LASHING DETAILS HAVE BEEN PROPERLY ADAPTED, ADEQUATE LAPS HAVE BEEN PROVIDED, CORRECT TYPE O SEALANT USED, ALL JOINTS ADEQUATELY CAULKED, AND PROESSIONAL WORKMANSHIP EMPLOYED. MANUACTURING INTRODUCTION TO TYPICAL DETAILS DATE: PAGE/ILE SD-2

9 NOMINAL COVERAGE 32" OR " 2.667" SEE BELOW 7/8" SECTION PROPERTIES THICKNESS GAGE INCHES (STEEL) WT. (PS) Y (KSI) IX (IN4/T) MA (T-LBS/T) ALLOWABLE UNIORM LOADS (PS) THICKNESS (INCHES) DEAD + LIVE LOAD (STRESS) 3'-0 3'-6 4'-0 4'-6 5'-0 LIVE LOAD DEL (L/240) 3'-0 3'-6 4'-0 4'-6 5' SECTION PROPERTIES AND ALLOWABLE STRESSES HAVE BEEN CALCULATED IN ACCORDANCE WITH 1986 AISI SPECIICATIONS OR THE DESIGN O COLD-ORMED STEEL STRUCTURAL MEMBERS. 2. PANEL STEEL CONORMS TO ASTM A653 GRADE C. 3. VALUES SHOWN AS ALLOWABLE LOADS ARE BASED ON PANELS COVERING THREE EQUAL CONTINUOUS SPANS. MULTIPLY THE VALUES BY 0.8 OR TWO SPAN ALLOWABLE LOADS. 4. THE PANEL WEIGHT HAS BEEN DEDUCTED ROM THE ALLOWABLE LOAD TABLES. 5. THE ALLOWABLE LOADS SHOWN ABOVE MAY BE INCREASED BY 33% OR WIND UPLIT. 6. SHEER DIAPHRAGM VALUE = 210#/L.. NOMINAL 1" TAPE SEALER # 10 X 1" WITH METAL BACKED NEOPRENE WASHER S-DECK PANEL SIDE LAP MANUACTURING OVERVIEW S-DECK DATE: PAGE/ILE SD-3

10 32" OR " NOMINAL COVERAGE 12 ASTENER LOCATED AS SHOWN S-DECK PANEL ASTENER SPACING AT END LAP 6" ASTENER WITH METAL BACKED NEOPRENE WASHER SEE PAGE SDI-3 OR ASTENER TYPES PANEL END LAP 32" OR " NOMINAL COVERAGE 6 ASTENER LOCATED AS SHOWN S-DECK PANEL INTERMEDIATE ASTENER SPACING # 10X1" 12" O.C. WITH METAL BACKED NEOPRENE WASHER ASTENER WITH METAL BACKED NEOPRENE WASHER SEE PAGE SDI-3 OR ASTENER TYPES 1" TAPE SEALER S-DECK PANEL SIDE LAP TYPICAL 32" OR " NOMINAL COVERAGE 12 ASTENER LOCATED AS SHOWN REERENCE DETAIL SD-10 SD-11 & SD-12 OR EAVE LASHING AND CLOSURE/TAPE SEALER INORMATION S-DECK PANEL EAVE ASTENER SPACING ASTENER WITH METAL BACKED NEOPRENE WASHER SEE PAGE SDI-3 OR ASTENER TYPES MANUACTURING ASTENER LAYOUT DATE: PAGE/ILE SD-4

11 S-DECK PANEL INSIDE OAM CLOSURE WITH TAPE SEALER TOP & BOTTOM PANEL ASTENER WITH METAL BACKED NEOPRENE WASHER AT 5 1/2" O.C. EAVE LASHING, 4" END LAPS WITH # 30 ELT UNDERLAYMENT ASTENERS, 20" O.C. MAX. 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING AND ASTENERS ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. 3. USE ICE AND WATERSHIELD AS UNDERLAYMENT OR CURVED S-DECK. MIN. 1" = INISH SIDE 1/2" EAVE LASHING MANUACTURING EAVE DETAIL PAGE/ILE SD-10

12 S-DECK PANEL INSIDE OAM CLOSURE WITH TAPE SEALER TOP & BOTTOM PANEL ASTENER WITH METAL BACKED NEOPRENE WASHER AT 5 1/2" O.C. ASTENERS, 20" O.C. MAX. EAVE LASHING, 4" END LAPS WITH WALL PANEL PURLIN 1. CAULKING AND ASTENERS ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. MIN. 1" = INISH SIDE 1/2" EAVE LASHING MANUACTURING EAVE DETAIL OPEN RAMING PAGE/ILE SD-11

13 S-DECK PANEL INSIDE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM PANEL ASTENER WITH METAL BACKED NEOPRENE WASHER AT 5 1/2" O.C. OUTSIDE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM ASTENER WITH METAL BACKED NEOPRENE WASHER 20" O.C. EAVE LASHING, 4" END LAPS WITH CONTINUOUS CAULK AT LAPS # 30 ELT UNDERLAYMENT ASTENERS, 20" O.C. MAX. S-DECK PANEL 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING AND ASTENERS ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. 3. USE ICE AND WATERSHIELD AS UNDERLAYMENT OR CURVED S-DECK. MIN. 1" = INISH SIDE 1/2" EAVE LASHING MANUACTURING EAVE DETAIL PAGE/ILE SD-12

14 RIDGE/HIP CAP; 4" END LAPS WITH. POP RIVET AT LAPS S-DECK PANEL PANEL ASTENER WITH METAL BACKED NEOPRENE WASHER ASTENERS WITH METAL BACKED NEOPRENE WASHER 20" O.C. OUTSIDE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM. USE 1" EXPANDABLE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM AT HIPS # 30 ELT UNDERLAYMENT 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELTING UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE 1/2" 1/2" RIDGE/HIP CAP MANUACTURING RIDGE AND HIP DETAIL PAGE/ILE SD-20

15 RIDGE CAP; 4" END LAPS WITH. POP RIVET AT LAPS S-DECK PANEL ASTENERS WITH METAL BACKED NEOPRENE WASHER 20" O.C. OUTSIDE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM PANEL ASTENER WITH METAL BACKED NEOPRENE WASHER ASTENER WITH METAL BACKED NEOPRENE WASHER. 40" O.C. MAX # 30 ELT UNDERLAYMENT LAP ELT OVER RIDGE 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELTING UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE 1/2" RIDGE CAP 1/2" MANUACTURING SHED ROO RIDGE CAP DETAIL PAGE/ILE SD-21

16 RIDGE/HIP CAP; 4" END LAPS WITH. S-DECK PANEL OUTSIDE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM. USE 1" EXPANDABLE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM AT HIPS PANEL ASTENER WITH METAL BACKED NEOPRENE WASHER ASTENERS WITH METAL BACKED NEOPRENE WASHER 20" O.C. SUB LASHING 4" END LAPS WITH CONTINUOUS CAULK AT LAPS PURLINS 1. ALL CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE 1/2" 1/2" SUB LASHING RIDGE/HIP CAP MANUACTURING RIDGE AND HIP DETAIL OPEN RAMING PAGE/ILE SD-22

17 SECTION VIEW IELD ORM END O RIDGE LASHING AND EXTEND UNDER UPPER PANEL S-DECK PANEL RIDGE LASHING; 4" END LAPS WITH IELD TAPERED OUTSIDE CLOSURE 1" EXPANDABLE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM SD-20 # 30 ELT UNDERLAYMENT VALLEY LASHING; 12" LAPS WITH PANEL ASTENER WITH METAL BACKED NEOPRENE WASHER AT 5 1/2" O.C. PLAN VIEW MAIN ROO PANELS RIDGE LASHING INSIDE OAM CLOSURE VALLEY LASHING DORMER PANEL MANUACTURING RIDGE TERMINATION AT DORMER VALLEY PAGE/ILE SD-23

18 CONTINUOUS BEAD O CAULK GABLE CHANNEL 4" END LAPS WITH S-DECK PANEL ASTENER 20" O.C. PLACE A DAB O CAULK AT ASTENER LOCATION DRIVE ASTENER AND CAULK ASTENER HEAD 1" EXPANDABLE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM 1/2" CONTINUOUS BEAD O CAULK ASTENERS; 20" O.C. MAX. DRIP LASHING; 4" END LAPS WITH # 30 ELT UNDERLAYMENT TOP LAYER O ELT TO BE PARALLEL WITH ROO SLOPE 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE 1/2" GABLE CHANNEL DRIP LASHING MANUACTURING GABLE DETAIL PAGE/ILE SD-30

19 CONTINUOUS BEAD O CAULK GABLE CHANNEL; 4" END LAPS WITH S-DECK PANEL ASTENER 20" O.C. PLACE A DAB O CAULK AT ASTENER LOCATION DRIVE ASTENER AND CAULK ASTENER HEAD 1" EXPANDABLE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM. 1/2" CONTINUOUS BEAD O CAULK ASTENERS; 20" O.C. WITH METAL BACKED NEOPRENE WASHER DRIP LASHING; 4" END LAPS WITH OUTSIDE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM S-DECK PANEL ASTENER AT EVERY PURLIN ASTENER 20" O.C. MAX PANEL ASTENER WITH METAL BACKED NEOPRENE WASHER ASTENER 20" O.C. MAX. PURLIN SUB LASHING 4" END LAPS WITH CONTINUOUS CAULK AT LAPS. 1. ALL CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE 1/2" GABLE CHANNEL DRIP LASHING SUB LASHING MANUACTURING GABLE DETAIL PAGE/ILE SD-31

20 CONTINUOUS BEAD O CAULK GABLE CHANNEL 4" END LAPS WITH S-DECK PANEL ASTENER 20" O.C. PLACE A DAB O CAULK AT ASTENER LOCATION DRIVE ASTENER AND CAULK ASTENER HEAD 1" EXPANDABLE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM 1/2" CONTINUOUS BEAD O CAULK DRIP LASHING; 4" END LAPS WITH WALL PANEL 30# ELT UNDERLAYMENT # 30 ELT UNDERLAYMENT TOP LAYER O ELT TO BE PARALLEL WITH ROO SLOPE ASTENERS; 20" O.C. MAX. 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE 1/2" GABLE CHANNEL DRIP LASHING MANUACTURING GABLE DETAIL PAGE/ILE SD-32

21 S-DECK PANEL ASTENERS WITH METAL BACKED NEOPRENE WASHER 20" O.C. MAX. CONTINUOUS BEAD O CAULK 1" EXPANDABLE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM. DRIP LASHING; 4" END LAPS WITH # 30 ELT UNDERLAYMENT TOP LAYER O ELT TO BE PARALLEL WITH ROO SLOPE ASTENERS; 20" O.C. MAX. 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ICE AND WATERSHIELD UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. 3. UNDERLAYMENT TO BE ICE AND WATERSHIELD OR CURVED PANELS. = INISH SIDE 1/2" DRIP LASHING MANUACTURING GABLE DETAIL CURVED PANELS PAGE/ILE SD-33

22 CAP LASHING; 4" END LAPS WITH. POP RIVET TO COUNTER LASHING 40" O.C. MAX. CAULK ALL RIVET HEADS ASTENERS; 20" O.C. MAX. COUNTERLASHING; 4" END LAPS WITH SUB-LASHING; 4" END LAPS WITH # 30 ELT UNDERLAYMENT OUTSIDE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM S-DECK PANEL 1 ON 12 ASTENERS AT LAPS AND STAGGERED; 20" O.C. AND CAULK ASTENER HEADS # 30 ELT UNDERLAYMENT ASTENERS; WITH METAL BACKED NEOPRENE WASHER. 40" O.C. MAX. PANEL ASTENERS; WITH METAL BACKED NEOPRENE WASHER. ASTENERS; WITH METAL BACKED NEOPRENE WASHER. 20" O.C. MAX. 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE 1 ON 12 1/2" COUNTERLASHING SUB-LASHING CAP LASHING MANUACTURING PARAPET DETAIL PAGE/ILE SD-40

23 S-DECK PANEL COUNTERLASHING; 4" END LAPS WITH. # 30 ELT UNDERLAYMENT SUB-LASHING; 4" END LAPS WITH INSIDE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM. ASTENERS; 20" O.C. MAX. OUTSIDE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM. ASTENERS; WITH METAL BACKED NEOPRENE WASHER. 20" O.C. S-DECK PANEL PANEL ASTENERS; WITH METAL BACKED NEOPRENE WASHER 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE 1/2" COUNTERLASHING SUB-LASHING MANUACTURING HEAD WALL DETAIL PAGE/ILE SD-41

24 REGLET LASHING; 4" END LAPS WITH ASTENERS; 20" O.C. MAX. COUNTERLASHING; 4" END LAPS WITH. REGLET CONTINUOUS CAULK AT REGLET SUB-LASHING; 4" END LAPS WITH # 30 ELT UNDERLAYMENT S-DECK PANEL OUTSIDE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM. CONTINUOUS BEAD O CAULK PANEL ASTENERS WITH METAL BACKED NEOPRENE WASHER. ASTENERS WITH METAL BACKED NEOPRENE WASHER. 20" O.C. 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE 1/2" COUNTERLASHING SUB-LASHING REGLET LASHING MANUACTURING HEAD WALL DETAIL PAGE/ILE SD-42

25 # 30 ELT UNDERLAYMENT ASTENERS 20" O.C. MAX. WALL PANEL COUNTER LASHING 4" END LAPS WITH SPECIAL CHANNEL CLOSURE BUTT END JOINTS OR WEEP CONTINUOUS BEAD O CAULK CONTINUOUS SUB LASHING 4" END LAPS WITH S-DECK PANEL # 30 ELT UNDERLAYMENT RAKE CHANNEL 4" END LAPS WITH CONTINUOUS CAULK AT LAPS 1" EXPANDABLE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM. TOP LAYER O ELT TO BE PARALLEL WITH ROO SLOPE ASTENER 20" O.C. PLACE A DAB O CAULK AT ASTENER LOCATION DRIVE ASTENER AND CAULK ASTENER HEAD 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE SPECIAL CHANNEL SUB LASHING COUNTER LASHING RAKE CHANNEL MANUACTURING RAKE WALL WITH WALL PANEL PAGE/ILE SD-50

26 S-DECK PANEL # 30 ELT UNDERLAYMENT ASTENERS 20" O.C. MAX PANEL ASTENER WITH METAL BACKED NEOPRENE WASHER AT 5 1/2" O.C. ASTENERS 20" O.C. MAX CONTINUOUS SUB LASHING 4" END LAPS WITH INSIDE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM COUNTER LASHING 4" END LAPS WITH CONTINUOUS BEAD O CAULK S-DECK PANEL # 30 ELT UNDERLAYMENT RAKE CHANNEL 4" END LAPS WITH CONTINUOUS CAULK AT LAPS 1" EXPANDABLE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM. TOP LAYER O ELT TO BE PARALLEL WITH ROO SLOPE ASTENER 20" O.C. PLACE A DAB O CAULK AT ASTENER LOCATION DRIVE ASTENER AND CAULK ASTENER HEAD 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE RAKE CHANNEL SUB LASHING COUNTER LASHING MANUACTURING RAKE WALL DETAIL PAGE/ILE SD-51

27 CONTINUOUS CAULK AT REGLET SAW CUT REGLET REGLET LASHING 4" END LAPS WITH CONTINUOUS BEAD O CAULK # 30 ELT UNDERLAYMENT COUNTER LASHING 4" END LAPS WITH ASTENERS 20" O.C. MAX CONTINUOUS SUB LASHING 4" END LAPS WITH CONTINUOUS BEAD O CAULK S-DECK PANEL # 30 ELT UNDERLAYMENT RAKE CHANNEL 4" END LAPS WITH CONTINUOUS CAULK AT LAPS 1" EXPANDABLE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM. TOP LAYER O ELT TO BE PARALLEL WITH ROO SLOPE ASTENER 20" O.C. PLACE A DAB O CAULK AT ASTENER LOCATION DRIVE ASTENER AND CAULK ASTENER HEAD 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE SUB LASHING COUNTER LASHING REGLET LASHING RAKE CHANNEL MANUACTURING RAKE WALL DETAIL WITH REGLET PAGE/ILE SD-52

28 CAP LASHING 4" END LAPS WITH CONTINUOUS CAULK AT LAPS 1 ON 12 ASTENERS 20" O.C. MAX. # 30 ELT UNDERLAYMENT CONTINUOUS CLEAT CONTINUOUS SUB LASHING 4" END LAPS WITH CONTINUOUS CAULK AT LAPS CONTINUOUS CLEAT COUNTER LASHING 4" END LAPS WITH CONTINUOUS BEAD O CAULK S-DECK PANEL # 30 ELT UNDERLAYMENT 1" EXPANDABLE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM. TOP LAYER O ELT TO BE PARALLEL WITH ROO SLOPE RAKE CHANNEL 4" END LAPS WITH CONTINUOUS CAULK AT LAPS ASTENER 20" O.C. PLACE A DAB O CAULK AT ASTENER LOCATION DRIVE ASTENER AND CAULK ASTENER HEAD 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE CAP LASHING SUB LASHING COUNTER LASHING RAKE CHANNEL MANUACTURING RAKE WALL PARAPET WALL PAGE/ILE SD-53

29 S-DECK PANEL PANEL ASTENER WITH METAL BACKED NEOPRENE WASHER AT 5 1/2" O.C. ASTENERS 20" O.C. MAX CONTINUOUS SUB LASHING 4" END LAPS WITH INSIDE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM COUNTER LASHING 4" END LAPS WITH CONTINUOUS BEAD O CAULK S-DECK PANEL RAKE CHANNEL 4" END LAPS WITH CONTINUOUS CAULK AT LAPS 1" EXPANDABLE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM. ASTENERS AT EVERY PURLIN PURLIN ASTENER 20" O.C. PLACE A DAB O CAULK AT ASTENER LOCATION DRIVE ASTENER AND CAULK ASTENER HEAD 1. ALL CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE RAKE CHANNEL SUB LASHING COUNTER LASHING MANUACTURING RAKE WALL DETAIL OPEN RAMING PAGE/ILE SD-54

30 ASTENERS 20" O.C. MAX. RAKE LASHING; BACK CUT VERTICAL LEG AND ORM TO RADIUS O ROO. 4" END LAPS WITH CONTINUOUS CAULK AT LAPS WALL PANEL CLOSURE ANGLE; BACK CUT VERTICAL LEG AS REQUIRED AND ORM TO RADIUS O ROO COUNTER LASHING; CUT TO MATCH RADIUS 4" END LAPS WITH CONTINUOUS BEAD O CAULK S-DECK PANEL 1" EXPANDABLE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM SUB LASHING; BACK CUT VERTICAL LEG AND ORM TO RADIUS O ROO. 4" END LAPS WITH CONTINUOUS CAULK AT LAPS ASTENERS 20" O.C. MAX ICE AND WATERSHIELD TOP LAYER O ICE AND WATERSHIELD TO BE PARALLEL WITH RAKE WALL 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ICE AND WATERSHIELD UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. 3. UNDERLAYMENT TO BE ICE AND WATERSHIELD OR CURVED PANELS. = INISH SIDE CUT TO MATCH RADIUS CLOSURE ANGLE SUB LASHING RAKE LASHING COUNTER LASHING MANUACTURING RAKE WALL CURVED PANELS PAGE/ILE SD-55

31 S-DECK PANEL UPPER PANEL PANEL ASTENERS; WITH METAL BACKED NEOPRENE WASHER AT 5 1/2" O.C. INSIDE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM 1 ON 12 MIN. SLOPE AWAY ROM UPER PANEL TRANSITION LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS S-DECK LOWER PANEL ASTENERS; 40" O.C. # 30 ELT UNDERLAYMENT ASTENER 20" O.C. PLACE A DAB O CAULK AT ASTENER LOCATION, DRIVE ASTENER THROUGH CAULK AND CAULK ASTENER HEADS. SUB-LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS PANEL ASTENERS; WITH METAL BACKED NEOPRENE WASHER ASTENERS; WITH METAL BACKED NEOPRENE WASHER. 20" O.C. OUTSIDE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE 1/2" 10" MIN. TRANSITION LASHING SUB-LASHING MANUACTURING SLOPE TRANSITION DETAIL PAGE/ILE SD-60

32 S-DECK PANEL CONTINUOUS BEAD O CAULK BETWEEN VALLEY LASHING AND ELT UNDERLAYMENT 1" EXPANDABLE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM ASTENERS 20" O.C. MAX. 9" MIN. # 30 ELT UNDERLAYMENT VALLEY LASHING 12" END LAPS WITH (2) CONTINUOUS BEADS CAULK AT LAPS PANEL ASTENER WITH METAL BACKED NEOPRENE WASHER AT 5 1/2" O.C. 1. (BY OTHERS) TO BE A MINIMUM O 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE 1/2" 20" MIN. VALLEY LASHING MANUACTURING VALLEY DETAIL PAGE/ILE SD-70

33 S-DECK PANEL CONTINUOUS BEAD O CAULK BETWEEN VALLEY LASHING AND ELT UNDERLAYMENT 1" EXPANDABLE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM ASTENERS 20" O.C. MAX. 9" MIN. GRACE ICE AND WATERSHIELD VALLEY LASHING 12" END LAPS WITH (2) CONTINUOUS BEADS CAULK AT LAPS PANEL ASTENER WITH METAL BACKED NEOPRENE WASHER AT 5 1/2" O.C. LAT SHEET VALLEY SUB-LASHING CORRUGATED S-DECK GRACE ICE AND WATER SHIELD RUN RIDGE TO EAVE LAT SHEET VALLEY SUB-LASHING RUN RIDGE TO EAVE SEE SECTION SLOPE LAT SHEET VALLEY SUB-LASHING GRACE ICE AND WATER SHIELD CORRUGATED S-DECK RIDGE EACH SIDE 16 GA. HAT SECTION PURLIN SLOPE 16 GA. HAT SECTION SIZED TO IT OVER PURLIN AND TO ACCOMMODATE THE DEPTH O THE CORRUGATED S-DECK. EAVE PURLINS CORRUGATED S-DECK SECTION ROOS WITH A SLOPE O 4:12 OR LESS 6'-0" MIN. ROOS ABOVE 4:12 3'-0" MIN. MANUACTURING VALLEY DETAIL OPEN RAMING PAGE/ILE SD-71

34 ROO PIPE PENETRATION O 4" IN DIA. OR LESS RUBBERIZED BOOT LASHING CONTINUOUS CAULK PIPE PENETRATION NOT TO BE AT PANEL SIDE LAP S-DECK PANEL SET RUBBERIZED BOOT INTO CONTINUOUS BEAD O CAULK. USE ASTENERS AS SPECIIED BY BOOT MANUACTURER. CAULK ASTENER HEADS # 30 ELT UNDERLAYMENT CUT PANEL 1" SMALLER THAN PENETRATION, BACK CUT TABS, OLD TABS UP AROUND PENETRATION, AND CAULK. NOTE: I PIPE IS MADE O METAL, IT MUST BE PAINTED TO PREVENT RUST RUN-O ROM STAINING PANELS. NOTE: POSITION SQUARE BASED BOOTS IN A DIAMOND ORIENTATION WHERE POSSIBLE TO AID IN DIVERTING WATER. MANUACTURING PIPE PENETRATION (PREERRED METHOD) IN PAN O PANEL ONLY 4" DIA. OR LESS PAGE/ILE SD-80

35 C B DETAIL SD-84 S-DECK PANEL INSIDE OAM CLOSURE INSTALL ATER LASHING "C" OUTSIDE OAM CLOSURE IELD CUT S-DECK ALONG LINE DETAIL SD-82 DETAIL SD-83 CONTINUOUS BEAD O CAULK AT ALL LASHING LAPS A B IELD CUT PANEL ALONG DOTTED LINE AND INSTALL PANEL. INSTALL LASHING "A" IRST ALONG WITH OAM CLOSURE. INSTALL LASHING "B" SECOND. CAULK ALL LASHING LAPS. INSTALL LASHING"C" LAST. THIS LASHING IS TO BE SLIPPED UNDER THE S-DECK PANEL AND ELT AS SHOWN IN DETAIL SD-84 BEORE THE OAM CLOSURE OR ASTENERS ARE INSTALLED. SEE ALSO DETAILS SD-82 AND SD-83 OR ELTING AND SUBLASHING. MANUACTURING ROO PENETRATION PAGE/ILE SD-81

36 ASTENERS; 20" O.C. MAX. COUNTERLASHING; 4" END LAPS WITH LASHING ROM MECHANICAL EQUIPMENT BY OTHERS PANEL ASTENERS WITH METAL BACKED NEOPRENE WASHER. OUTSIDE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM S-DECK PANEL CONTINUOUS ANGLE LASHING TYPICAL ALL 4 SIDES O PENETRATION # 30 ELT UNDERLAYMENT TOP LAYER O # 30 ELT UNDERLAYMENT TO BE PERPENDICULAR TO ROO SLOPE ASTENERS WITH METAL BACKED NEOPRENE WASHER. 20" O.C. MAX. 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE 8" 8" 1/2" COUNTER LASHING SIDE A ANGLE LASHING MANUACTURING ROO PENETRATION SIDE A PAGE/ILE SD-82

37 LASHING ROM MECHANICAL EQUIPMENT BY OTHERS ASTENERS; 20" O.C. TYP. # 30 ELT UNDERLAYMENT CONTINUOUS ANGLE TYPICAL ALL 4 SIDES O PENETRATION # 30 ELT UNDERLAYMENT COUNTER LASHING 4" END LAPS WITH CONTINUOUS BEAD O CAULK S-DECK PANEL # 30 ELT UNDERLAYMENT 1" EXPANDABLE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM TOP LAYER O ELT TO BE PARALLEL WITH ROO SLOPE RAKE CHANNEL 4" END LAPS WITH CONTINUOUS CAULK AT LAPS ASTENER 20" O.C. PLACE A DAB O CAULK AT ASTENER LOCATION DRIVE ASTENER AND CAULK ASTENER HEAD 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE RAKE CHANNEL ANGLE LASHING SIDE B COUNTER LASHING MANUACTURING ROO PENETRATION SIDE B PAGE/ILE SD-83

38 CONTINUOUS COUNTER LASHING INSTALL ATER PANEL INSTALLATION. SLIP LASHING UP UNDER ELT AND PANEL COUNTER LASHING ROM MECHANICAL EQUIPMENT BY OTHERS S-DECK PANEL INSIDE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM INSTALL ATER CONTINUOUS COUNTER LASHING # 30 ELT UNDERLAYMENT PANEL ASTENERS WITH METAL BACKED NEOPRENE WASHER AT 5 1/2" O.C. SLIP COUNTER LASHING UNDER ELT BEORE ASTENING PANEL CONTINUOUS ANGLE LASHING TYPICAL ALL 4 SIDES O ROO PENETRATION CONTINUOUS BEAD O CAULK BETWEEN LASHING AND ELT SCRAP S-DECK PANEL UNDER COUNTER LASHING OR SUPPORT 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE ANGLE LASHING MANUACTURING ROO PENETRATION SIDE C COUNTER LASHING SIDE C PAGE/ILE SD-84

39 1'-0" MINIMUM 1'-0" MINIMUM OR ROO PENETRATIONS LARGER THAN 4" IN DIA. CARRY UP TO NEXT PURLIN GRACE ICE AND WATER SHIELD RUN CONTINUOUS TO EAVE SQUARE OR ROUND PENETRATION LAT SHEET SUB-LASHING RUN CONTINUOUS TO EAVE SLOPE CORRUGATED S-DECK SEE SECTION PURLINS EAVE LAT SHEET SUB LASHING GRACE ICE AND WATER SHIELD 16 GA. HAT SECTION SIZE TO IT OVER PURLIN AND TO ACCOMMODATE THE DEPTH O THE CORRUGATED S-DECK. 16 GA. HAT SECTION PURLIN CORRUGATED S-DECK SECTION MANUACTURING PENETRATION LARGER THAN 4" OPEN RAMING PAGE/ILE SD-85

40 S-DECK PANEL CONTINUOUS BEADS O CAULK INSIDE CORNER LASHING; 4" END LAPS WITH POP RIVET 20" O.C. RAKE CHANNEL; 4" END LAPS WITH. 1" EXPANDABLE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM SUB-LASHING; 4" END LAPS WITH ASTENERS 20" O.C. PLACE A DAB O CAULK AT ASTENER LOCATION DRIVE ASTENER AND CAULK ASTENER HEAD. # 30 ELT UNDERLAYMENT ASTENERS; 20" O.C. MAX. 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE RAKE CHANNEL CORNER LASHING SUB-LASHING MANUACTURING INSIDE CORNER PAGE/ILE SD-90

41 OUTSIDE CORNER LASHING; 4" END LAPS WITH. POP RIVET 20" O.C. CONTINUOUS BEADS O CAULK S-DECK PANEL RAKE CHANNEL; 4" END LAPS WITH. # 30 ELT UNDERLAYMENT SUB-LASHING; 4" END LAPS WITH 1" EXPANDABLE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM. ASTENERS; 20" O.C. MAX. ASTENERS; 20" O.C. PLACE A DAB O CAULK AT ASTENER LOCATION DRIVE ASTENER AND CAULK ASTENER HEAD. 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE RAKE CHANNEL SUB-LASHING OUTSIDE CORNER LASHING MANUACTURING OUTSIDE CORNER PAGE/ILE SD-91

42 S-DECK PANEL CONTINUOUS BEADS O CAULK INSIDE CORNER LASHING; 4" END LAPS WITH POP RIVET 20" O.C. RAKE CHANNEL; 4" END LAPS WITH 1" EXPANDABLE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM SUB-LASHING; 4" END LAPS WITH PURLIN ASTENERS; AT PURLINS ASTENERS 20" O.C. PLACE A DAB O CAULK AT ASTENER LOCATION DRIVE ASTENER AND CAULK ASTENER HEAD. 1. ALL CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE RAKE CHANNEL CORNER LASHING SUB-LASHING MANUACTURING INSIDE CORNER OPEN RAMING PAGE/ILE SD-92

43 OUTSIDE CORNER LASHING; 4" END LAPS WITH POP RIVET 20" O.C. CONTINUOUS BEADS O CAULK S-DECK PANEL RAKE CHANNEL; 4" END LAPS WITH ASTENERS AT PURLINS ASTENERS; 20" O.C. PLACE A DAB O CAULK AT ASTENER LOCATION DRIVE ASTENER AND CAULK ASTENER HEAD. SUB-LASHING; 4" END LAPS WITH 1" EXPANDABLE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM. PURLIN 1. ALL CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE RAKE CHANNEL SUB-LASHING OUTSIDE CORNER LASHING MANUACTURING OUTSIDE CORNER OPEN RAMING PAGE/ILE SD-93

44 S-DECK PANEL INSIDE CORNER LASHING; 4" END LAPS WITH # 30 ELT UNDERLAYMENT ASTENERS; 20" O.C. MAX. OUTSIDE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM. ASTENERS; WITH METAL BACKED NOEPRENE WASHER. 20" O.C. S-DECK PANEL ASTENERS; WITH METAL BACKED NOEPRENE WASHER. 20" O.C. PANEL ASTENERS; WITH METAL BACKED NOEPRENE WASHER ASTENERS; 20" O.C. MAX. SUB-LASHING; 4" END LAPS WITH PANEL ASTENERS; WITH METAL BACKED NOEPRENE WASHER 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE CORNER LASHING SUB-LASHING MANUACTURING INSIDE CORNER PAGE/ILE SD-94

45 OUTSIDE CORNER LASHING; 4" END LAPS WITH. PANEL ASTENERS; WITH METAL BACKED NEOPRENE WASHER. ASTENERS; WITH METAL BACKED NEOPRENE WASHER. 20" O.C. S-DECK PANEL # 30 ELT UNDERLAYMENT ASTENERS; 20" O.C. MAX. SUB-LASHING; 4" END LAPS WITH OUSIDE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM. ASTENERS; WITH METAL BACKED NEOPRENE WASHER. 20" O.C. ASTENERS; 20" O.C. MAX. S-DECK PANEL 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE SUB-LASHING OUTSIDE CORNER LASHING MANUACTURING OUTSIDE CORNER PAGE/ILE SD-95

46 # 30 ELT UNDERLAYMENT ASTENERS 20" O.C. MAX. PANEL ASTENER WITH METAL BACKED NEOPRENE WASHER AT 5 1/2" O.C. S-DECK PANEL INSIDE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM. DRIP LASHING 4" END LAPS WITH HEAD 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE DRIP LASHING MANUACTURING HEAD DETAIL PAGE/ILE SD-96

47 # 30 ELT UNDERLAYMENT ASTENERS 20" O.C. MAX. PANEL ASTENER WITH METAL BACKED NEOPRENE WASHER AT 5 1/2" O.C. S-DECK PANEL INSIDE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM. DRIP LASHING 4" END LAPS WITH 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE DRIP LASHING MANUACTURING SLAB DETAIL PAGE/ILE SD-97

48 SILL CONTINUOUS BEAD O CAULK OUTSIDE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM. S-DECK PANEL CLOSURE 4" END LAPS WITH PANEL ASTENER WITH METAL BACKED NEOPRENE WASHER AT 20" O.C. # 30 ELT UNDERLAYMENT 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE CLOSURE MANUACTURING SILL DETAIL PAGE/ILE SD-98

49 ASTENER 20" O.C. PLACE A DAB O CAULK AT ASTENER LOCATION DRIVE ASTENER AND CAULK ASTENER HEAD GABLE CHANNEL 4" END LAPS WITH CONTINUOUS CAULK AT LAPS 1" EXPANDABLE OAM CLOSURE WITH TAPE SEALER TOP AND BOTTOM. # 30 ELT UNDERLAYMENT S-DECK PANEL JAMB CONTINUOUS BEAD O CAULK 1. (BY OTHERS) TO BE MINIMUM 1/2" PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE MANUACTURING GABLE CHANNEL JAMB DETAIL PAGE/ILE SD-99