SCHMEISER PRECISION FINISHING SCRAPER 10 FT. to 24 FT. WIDE

Size: px

Start display at page:

Download "SCHMEISER PRECISION FINISHING SCRAPER 10 FT. to 24 FT. WIDE"

Shona Booth
5 years ago
Views:

1 SCHMEISER PRECISION FINISHING SCRAPER 0 FT. to FT. WIDE ASSEMBLY & PARTS MANUAL T.G. SCHMEISER CO., INC. P.O. BOX 0 FRESNO, CA () - FAX () - VERSION. COPYRIGHT 0 T.G.SCHMEISER CO., INC. OCTOBER 0

2 INTRODUCTION Your Schmeiser Finishing Scraper is designed to give you many years of dependable service. This manual has been prepared to instruct you in the safe and efficient operation of this machine. Read and study it thoroughly. Follow all instructions carefully. Should your Finishing Scraper require replacement parts, go to your Schmeiser dealer. Always order genuine Schmeiser replacement parts. It is important that you complete and send in your Warranty Card because it is not valid unless it is on file at Schmeiser. If you need information not contained in this manual, contact your Schmeiser dealer. Space has been provided below for you to record the model number and serial number of your Finishing Scraper. Be sure to bring this information with you to your dealer when ordering parts or attachments for your Finishing Scraper. Thank you for buying a Schmeiser Finishing Scraper. SERIAL NUMBER MODEL NUMBER DATE PURCHASED DEALER NAME () - Fax () -

3 TABLE OF CONTENTS Introduction... Table of Contents... Safety Sheet... Finishing Scraper Assembly Instructions... - Complete Rigid Finishing Scraper Assembly... - Complete Folding Finishing Scraper Assembly Pull Frame and Braces Assembly (rigid models)... Pull Frame and Braces Assembly (folding models)... Rear Wheel Axle Assembly... Rear Wheel Axle Adjustment Bolt Assembly... Walking Beam Assembly... Rear Wheel Axle Spindle and Hub Assembly... Laser Tower/GPS Stand Assembly... Transport Wheel Axle Assembly (for units with Transport Option)... Transport Wheel Axle Spindle and Hub Assembly (Optional)...0 Transport Tongue Assembly (Optional)... Transport Tongue Turnbuckle Assembly (Optional)... Swivel Hitch Assembly (Optional)... Hydraulic Diagrams... - Limited Warranty... Maintenance and Repair Record Sheet...

4 SAFETY The safe operation of any machinery is an important concern to farmers and manufactures. There are obvious and hidden potential hazards involved in the operation of this implement. Carefully read and follow all safety precautions before operation. Serious injury or death may occur unless care is taken to insure the safety of both the operator and any other persons in the area This is a rear-mounted implement that removes weight from the front wheels of the tractor and can cause loss of steering with possible overturn. Add front-end weight until at least 0% of tractor original weight is on the front wheels when leveler is in transport position for steering and prevention of bodily injury. When on rough surfaces, transport slowly to prevent bouncing front wheels off surface with loss of steering and possible injury. Be especially careful when transporting on slopes. Never turn uphill in transport except at slow speed and a low rate of turn. Never transport or operate this machine on steep slopes. Never permit anyone to ride on or walk beside the implement when moving. Never permit anyone to ride on tractor when implement is being moved. Never allow anyone to be near the implement when performing operating functions with implement or tractor. Do not enter tractor when tractor is moving. Avoid serious injury or death from contact with rotating tires. Enter and exit the tractor only when it is completely stopped. When in transport, use accessory lights and devices for adequate warning to operators of other vehicles. Comply with all Federal, State, and local laws when traveling on public roads. Use Slow Moving Vehicle emblem for warning vehicles approaching from the rear. When transporting, remember that the implement may be wider than your tractor and extreme care must be taken to allow for safe clearance. Never allow inexperienced or untrained personnel to operate the implement or tractor without supervision. When using compressed air to clean implement, wear safety glasses. Check all fasteners for tightness or damage before and after operation. Repair immediately if required. Store implement in a stable position. () - Fax () -

5 FINISHING SCRAPER ASS'Y INSTRUCTIONS STRAIGHT PULL MODELS (0' THROUGH ' UNITS) Select a smooth, level area approximately feet wide and feet long. Position main frame on the ground on wooden blocks and center in the area with the open bucket facing the direction that the machine is to be pulled. Position and attach tongue to the main frame with () " x " NC Cap Screws and with lock washers and hex nuts. Hoist and attach left brace and right brace with () " x -/" NC Cap Screws with lock washers and hex nuts on each side. See page 0 for reference. Install () " x " Tie Rod Hydraulic Cylinders on the main bucket. Connect cap ends of the cylinders (bottom ends) to the cylinder anchors on the main bucket using cylinder lockout pins with cotter pins. Using hoist, pick up right side portion of wheel axle, align cylinder anchor on the wheel axle with cylinder anchor on the main bucket. Connect wheel axle and main bucket using " pivot pins with /" x -/" NC cap screw, lock washer, and hex nuts. Refer to page for details. Using hoist, pick up left side portion of wheel axle, align adjustment bolt on the wheel axle with cylinder anchor on the main bucket. Connect wheel axle and main bucket using " pivot pins. Refer to page for details. Connect rod ends of the hydraulic cylinders to the flip lockout bars and wheel axle (right side -to the wheel axle cylinder anchor, left side - to the wheel axle adjustment bolt) using " x -/" Gr. NC cap screws with nylon lock hex nuts. Attach walking beam assemblies to the wheel axle. Use " pivot pins. See drawing on page for proper installation. For units ' and smaller, mount.x tires to the spindles on the walking beams. Mount.x tires for ' and larger units. Ensure that valve stems are to the inside. Tighten all bolts securely. Mount laser tower(s) to the main bucket using () /" x " NC Cap Screws with lock washers and hex nuts for each tower. Refer to page 0 for details. Mount GPS tower to the main bucket using () /" x " NC Cap Screws with lock washers and hex nuts. Install main bucket blades using /" x -/" NC Plow Bolts with lock washers and hex nuts. See page for details. Install adjustable side blades using /" x -/" NC Cap Screws with flat washers, lock washers, and hex nuts. See page for details. ATTENTION: ENSURE THAT REAR WHEEL AXLE CENTER PLATES ARE NOT BOLTED TOGETHER FOR UNITS WITH TWO TOWERS! () - Fax () -

6 FINISHING SCRAPER ASS'Y INSTRUCTIONS END-TOW MODELS (0' AND UP UNITS) Select a smooth, level area approximately 0 feet wide and 0 feet long. Position main frame on the ground on wooden blocks and center in the area. Position and attach tongue to the main frame with " hinge pin with /" x " NC cap screw, lock washer, and hex nut. Hoist and attach left brace and right brace to the main frame with -/" brace pins with cotter pins on each side. See page for reference. Attach both braces to the tongue with - /" brace locking pins with /" lynch pins. Using hoist, pick up right side portion of wheel axle, align cylinder anchor on the wheel axle with cylinder anchor on the main bucket. Connect wheel axle leg to the main bucket using " pivot pin with /" x -/" NC cap screw, lock washer, and hex nut (refer to page for details). Using hoist, pick up left side portion of wheel axle, align adjustment bolt on the wheel axle with cylinder anchor on the main bucket. Connect wheel axle leg to the main bucket using " pivot pin with /" x -/" NC cap screw, lock washer, and hex nut (refer to page for details). Install () " x " tie rod hydraulic cylinders on the back of the main bucket. Connect cap ends of the cylinders (bottom ends) to the cylinder anchors on the main bucket using cylinder pins with cotter pins. Connect rod ends of the hydraulic cylinders to the flip lockout bars and wheel axle (right side - to the wheel axle cylinder anchor, left side - to the wheel axle adjustment bolt) using " x -/" Gr. NC cap screws with nylon lock hex nuts. Attach walking beam assemblies to the wheel axle. Use " pivot pins. See drawing on page for proper installation. Mount. x tires to the spindles on the walking beams. Ensure that valve stems are to the inside. Tighten all bolts securely. Mount laser tower(s) to the main bucket using () /" x " NC cap screws with lock washers and hex nuts for each tower. Refer to page 0 for details. Mount GPS tower to the main bucket using () /" x " NC Cap Screws with lock washers and hex nuts. Install main bucket blades using /" x -/" NC plow bolts with lock washers and hex nuts. See page for details.. Install adjustable side blades using /" x -/" NC cap screws with flat washers, lock washers, and hex nuts. See page for details ATTENTION: ENSURE THAT REAR WHEEL AXLE CENTER PLATES ARE NOT BOLTED TOGETHER FOR UNITS WITH TWO TOWERS! () - Fax () -

7 FINISHING SCRAPER ASS'Y INSTRUCTIONS END-TOW MODELS (0' AND UP UNITS) TRANSPORT OPTION ASSEMBLY: Using hoist, install transport wheel axle on top of the main bucket with jog facing direction in which machine will be pulled. Connect transport wheel axle and main frame pivot points on each side of the bucket using " pivot pins with /" x " NC cap screws, lock washers and hex nuts. See illlustration on page for proper installations. Install () " x 0" tie rod hydraulic cylinders on the main bucket. Connect cap ends of the cylinders (bottom ends) to the cylinder anchors on the main bucket using cylinder pins with cotter pins. Connect rod ends of the hydraulic cylinders to the flip lockout bars and wheel axle cylinder anchors using " x -/" Gr. NC cap screws with nylon lock hex nuts (refer to page ). Mount highway tires to the removable spindles on the wheel axle. Tighten all bolts securely. Refer to page 0. Mount transport tongue to the R.H. side of the main frame behind the bucket using " x " NC cap screw with nylon lock hex nut. See page and for detailed instructions. Connect turnbuckle assembly to the transport tongue using " x -/" pin with /" lynch pin. Mount other side of the turnbuckle to the main frame bucket using " x -/" NC cap screw with nylon lock hex nut. Refer to page for details. Adjust turnbuckle to the desired hitch height. () - Fax () -

8 RIGID UNIT ASSEMBLY Item No. Part No. Description Qty./Machine SFS-00A00 Pull Frame SFS-00A00 Pull Frame Brace SFS-0A0 ' Scraper Blade Varies SFS-00A0 Adjustment Side Blade GHC-00T " x" Hydraulic Cylinder GWT-0 GWT-0.x 0 Ply Tire w/ Whee (' Units & Up).X 0 Ply Tire w/wheel (' Units & Under) GWD-LB " x " Lockout Bar SFS-00A00 Laser Tower Varies SFS-00A Tower Support Brace Varies 0 GMB-HITCHCA PFS-SWH Perfect Hitch Cat. Swivel Hitch (Optional) () - Fax () -

9 RIGID UNIT ASSEMBLY 0 () - Fax () -

10 FOLDING UNIT ASSEMBLY Item No. Part No. Description Qty./Machine SFS-00B00 Pull Frame SFS-00B00 Pull Frame Brace SFS-00B Pull Frame Support SFS-0A0 ' Scraper Blade Varies SFS-00A0 Adjustment Side Blade SFS-00B00 Transport Tongue GHC-000T " x 0" Hydraulic Cylinder GWT-0 GWT-0. X 0 Ply Tire W/Wheel (' units & up). x 0 Ply Tire w/wheel (' units & under) GWD-LB " x " Lockout Bar 0 SFS-00A00 Laser Tower Varies SFS-00A Tower Support Brace Varies GWT-R -R Highway Tire GMB-HITCHCA PFS-SWH (Optional) Perfect Hitch Cat. Swivel Hitch GWD-0LB " x 0" Lockout Bar GHC-00T " x " Hydraulic Cylinder SGB-00F00 Wheel Axle Lockout Weldment () - Fax () - 0

11 FOLDING UNIT ASSEMBLY 0 () - Fax () -

12 RIGID PULL FRAME ASSEMBLY 0 Ref No. Part No. Description Qty. SFS-00A00 Main Frame SFS-00A00 Pull Frame Brace Weldment SFS-00A00 Rigid Pull Frame Weldment GMB-HITCHCA CSNC LWASHER- Perfect Hitch Cat IV " x " NC Cap Screw " Lock Washer HXNUT-NC " NC Hex Nut CSNC00 " x -/" NC Cap Screw CSNC0 " x " NC Cap Scew 0 A Hose Holder (Short) CSNC00 /" x -/" NC Cap Screw FWASHER-0 /" Flat Washer LWASHER-0 /" Lock Washer HXNUT-0NC /" NC Hex Nut () - Fax () -

13 FOLDING PULL FRAME ASS'Y 0 0 Rotate to Transport 0 0 Ref No. Part No. Description SFS-00B00 Main Frame Weldment SFS-00B00 GMB-HITCHCA Folding Pull Frame Perfect Hitch Cat. IV CSNC " x " NC Cap Screw LWASHER- " Lock Washer HXNUT-NC " NC Hex Nut SFS-00B0 Pull Frame Hinge Pin SFS-00B0 Main Frame-Brace Pivot Pin SFS-00B0 Pull Frame-Brace Removable Locking Pin 0 GPN-00LYN /" Lynch Pin SFS-00B00 Folding Pull Frame Brace Weldment A Hose Holder (Short) SFS-00B Pull Frame/Brace Support Weldment CSNC00 /" X -/" NC Cap Screw LWASHER-0 /" Lock Washer HXNUT-0NC /" NC Hex Nut CSNC00 /" x 0" NC Cap Screw SFS-00B Brace and Tongue Locking Spacer LWASHER-0 /" Lock Washer 0 HXNUT-0NC /" NC Hex Nut CSNC00 /" x -/" NC Cap Screw FWASHER-0 /" Flat Washer Qty. () - Fax () -

REAR WHEEL AXLE ASSEMBLY * PLACE SFS-00A0 & GPN-00LYN HERE WHEN MACHINE IN FIELD POSITION. * 0 ENSURE THAT AXLE CENTER PLATES ARE NOT BOLTED TOGETHER FOR UNITS WITH TWO TOWERS! Ref No. Part No.

14 REAR WHEEL AXLE ASSEMBLY * PLACE SFS-00A0 & GPN-00LYN HERE WHEN MACHINE IN FIELD POSITION. * 0 ENSURE THAT AXLE CENTER PLATES ARE NOT BOLTED TOGETHER FOR UNITS WITH TWO TOWERS! Ref No. Part No. Description SFS-00B00 Main Frame Weldment SFS-00B0WH Walking Beam Pivot Pin GBR-XTX -/" O.D. Tension Bushing CSNC00 " x " N.C. Hex Bolt LWASHER- " Lock Washer HXNUT-NC " NC Hex Nut SFS-00A00 CSNC00 LWASHER-0 Rear Wheel Axle Weldment (R.H. Shown) /" x -/" Cap Screw /" Lock Washer 0 HXNUT-0NC /" NC Hex Nut GHC-00T " x " Tie Rod Hyd. Cylinder GPN-HC GPN-0CLIP " x " Cylinder Pin /" Hair Pin Clip CSNC0 " x -/" Gr. NC Cap Screw NYNUT-NC " NC Nylon Nut Hex Nut SFS-00A0 W.A. Cylinder Lockout Plate SFS-00A0 Cylinder Lockout Pin GPN-00LYN /" Lynch Pin GWD-LB Lockout Bar for " x " Hyd. Cylinder () - Fax () - Qty.

15 REAR WHEEL AXLE ADJUSTMENT BOLT ASS'Y 0 Ref No. Part No. Description Qty. Per Machine GHC-00T GPN-HC GPN-0CLIP SFS-00A00 HXNUTJNC " x " Hyd. Cylinder " x " Cylinder Pin /" Hair Pin Clip Wheel Leg Adjustment Bolt -/" NC Hex Jam Nut LWASHER-S -/" Internal Star lock Washer SFS-00A Adjustment Bolt Wrench CSNC0 " X -/" Gr. NC Cap Screw NYNUT-NC " NC Nylon Lock Hex Nut 0 GWD-LB Lockout for " x " Hyd. Cylinder () - Fax () -

WALKING BEAM ASSEMBLY 0 Ref No. Part No. Description Qty. Per Machine SFS-00A00 Wheel Axle Weldment (L.H. & R.H.) SFS-00B00L Walking Beam Weldment L.H SFS-00B00R GBR-XTX Walking Beam Weldment R.H. (Shown) -/" O.

16 WALKING BEAM ASSEMBLY 0 Ref No. Part No. Description Qty. Per Machine SFS-00A00 Wheel Axle Weldment (L.H. & R.H.) SFS-00B00L Walking Beam Weldment L.H SFS-00B00R GBR-XTX Walking Beam Weldment R.H. (Shown) -/" O.D. Tension Bushing 0 SFS-00B0WH Walking Beam Pivot Pin CSNC00 /" x -/" NC Hex Bolt LWASHER-0 /" Lock Washer HXNUT-0NC /" NC Hex Nut CSNC00 /" x -/" NC Hex Bolt HXNUT-0NC /" NC Hex Nut 0 SFS-00B00 -/" Removable Spindle () - Fax () -

17 REAR WHEEL AXLE HUB ASSEMBLY 0 Ref No. Part No.. SFS-00B00L SFS-00B00R. CSNC00. LWASHER-0. HXNUT-0NC. CSNC00.. HXNUT-0NC SFS-00B00. GHB-XXGSL. GHB-XXICN 0. GHB-XXIRC. GHB-XXORC. GHB-XXOCN. GSP-SPWA. GSP-CANT. GPN-0XC. GWT-0 GWT-0.. WHN-0NFWN GHB-XXCAP. GHB-XXHZ Description Walking Beam Weldment (Left) Walking Beam Weldment (Right) /" x -/" NC Cap Screw /" Lock Washer /" Hex Nut /" x -/" NC Cap Screw /" Hex Nut -/" Removable Spindle Grease Seal Inner Bearing Cone for on XHVY Hub Inner Bearing Cup for on XHVY Hub Outer Bearing Cup for on XHVY Hub Outer Bearing Cone for on XHVY Hub " Dia. Spindle Flat Washer " Dia. Spindle Castle Nut /" x " Cotter Pin. X 0 Ply Tire W/Wheel Assembly (' Units & Smaller). X 0 Ply Tire W/Wheel Assembly (' Units & Larger) Hub Lug Nuts /" NF for on XHVY Hub Hub Cap on XHVY Hub Ass'y w/ Bearings and Grease Seals (Includes Items - & ) Qty. Per Hub () - Fax () -

18 LASER/GPS TOWER ASSEMBLY GPS STAND OPTION LASER TOWER OPTION * Ref No. Part No. Description Qty. SFS-00B00 Main Frame Weldment SFS-00A00 Laser Tower Weldment Varies SFS-GPS GPS Stand Weldment Varies * CSNC0 /" x " NC Cap Screw (Laser Tower) Per Tower CSNC0 /" x " NC Cap Screw (GPS Tower) Per Tower LWASHER- /" Lock Washer Per Tower HXNUT-NC /" NC Hex Nut Per Tower () - Fax () -

19 TRANSPORT WHEEL AXLE ASSEMBLY 0 Ref No. Part No. SFS-00B00 SFS-00B GBR-G CSNC00 GPN-0CLIP GPN-HC GHC-000T CSNC0 NYNUT-NC 0 GWD-0LB LWASHER-0 HXNUT-0NC GPN-X0 GPN-00LYN SGB-00F00 CSNC0 CSNC00 Description Transport Axle Weldment Pivot Pin Weldment -/" O.D. Self Lubricating Bushing /" x -/" NC Cap Screw /" Hair Pin Clip " X " Cylinder Pin " X 0" Tie Rod Hydraulic Cylinder " x -/" Gr. NC Cap Screw " NC Nylon Lock Hex Nut Lockout Bar for " x 0" Hyd. Cylinder /" Lock Washer /" NC Hex Nut " X " Clevis Pin /" Lynch Pin Wheel Axle Lockout Weldment " x " NC Cap Screw Qty. Per Machince /" x -/" NC Cap Screw () - Fax () -

20 TRANSPORT WHEEL AXLE SPINDLE & HUB ASSEMBLY 0 Ref No. Part No. Description Qty. Per Machine SFS-00B00 Transport Wheel Axle Weldment CSNC00 LWASHER-0 HXNUT-0NC SFS-00B0 /" x -/" NC Cap Screw /" Lock Washer /" NC Hex Nut -/" Removable Spindle GHB-XGSL Oil Shield For On Heavy Hub GBH-XICN GBH-XIRC Inner Bearing Cone for On Hub Inner Race For ON Heavy Hub GHB-XHVY Hub, On Heavy Complete (Includes items - & ) 0 GHB-XORC Outer Bearing Race For On Heavy Hub GHB-XOCN Outer Bearing Cone For On Heavy Hub GSP-SPWA /" Flat Washer, Spindle GSP-CANT GPN-0X0C /" Castle Nut, Spindle /" x -/" Cotter Pin GWT-R Highway Tire WHB-0X0 Wheel Bolts for on Heavy Hub GHB-XCAP Dust Cap For On Heavy Hub () - Fax () - 0

21 TRANSPORT TONGUE ASSEMBLY 0 Ref No. Part No. Description Qty.. CSNC0 " x -/" NC Cap Screw. NYNUT-NC " NC Nylon lock Nut. GTB-00A00 -/" ACME Turnbuckle Body. SFS-00B " x -/" Pin. GPN-00LYN /" Lynch Pin. SFS-00B00 Tansport Tongue Weldment. GBH-XT " O.D. Tension Bushing.. SFS-00B Bottom Turnbuckle Rod Weldment R.H.. 0. SFS-00B GJK-KTW Top Turnbuckle Rod Weldment L.H. 000# Cap Jack Stand. CSNC " x " NC Cap Screw. SFS-00B Turnbuckle Adjustment Rod. GPN-0SL /" x -/" Hitch Pin () - Fax () -

TRANSPORT TONGUE TURNBUCKLE * 0 Ref No. Part No. Description SFS-00B00 Main Frame Weldment SFS-00B00 Transport Tounge Weldment SFS-00B BottomTurnbuckle Rod Weldment R.H.

22 TRANSPORT TONGUE TURNBUCKLE * 0 Ref No. Part No. Description SFS-00B00 Main Frame Weldment SFS-00B00 Transport Tounge Weldment SFS-00B BottomTurnbuckle Rod Weldment R.H. GTB-00A00 -/" ACME Turnbuckle Body SFS-00B Top Turnbuckle Rod Weldment L.H. SFS-00B Turnbuckle Adjustment Rod CSNC0 " x " NC Cap Screw NYNUT-NC " NC Nylon Lock Nut 0 SFS-00B GPN-00LYN " x -/" Pin /" Lynch Pin CSNC " x " NC Cap Screw GPN-0SL /" X -/" Hitch Pin with Handle *NOTE: ENSURE TURNBUCKLE ADJUSTMENT ROD IS PLACED INSIDE OF TURNBUCKLE BODY TO PREVENT TURNBUCKLE ROD FROM ROTATING OUT WHEN IN FIELD POSITION. Qty. () - Fax () -

24 HYDRAULIC DIAGRAM FOR UNITS WITH TOWER REAR B B # A A # B B # A A # # # HYD. LINE " LONG HYD. LINE " LONG HYDRAULIC CYLINDERS () X TIE ROD CYL. HOSES # - MP-MJ 00" LONG # - MJ-FJX 00" LONG # - SEE TABLE # - SEE TABLE REQ'D () () () () # # C C FRONT ALL HOSES ARE MEGATOUGH! SIZE HOSE # HOSE # FT " 0" FT " 0" FT " " FT 0" " 0FT " " FITTINGS A - /" MJHT TEE FITTING A - /" HN- LOCK NUT B - MB-MJ0º ELBOW C - /" PIONEER TIP REQ'D () - ON MANIFOLD () - ON MANIFOLD () () FT " 0" FT " " NOTE: HOSES # AND # ARE FJX-FJX () - Fax () -

25 HYDRAULIC DIAGRAM FOR UNITS WITH TOWERS REAR B B # A A A A # B B # A A A A # # # # # D D D D HYD. LINE " LONG HYD. LINE " LONG HYD. LINE " LONG HYD. LINE " LONG ALL HOSES ARE MEGATOUGH! HYDRAULIC CYLINDERS () X TIE ROD CYL. # # # # SIZE HOSE # HOSE # FT " 0" HOSES # - MP-MJ 00" LONG # - MJ-FJX 00" LONG # - SEE TABLE # - SEE TABLE REQ'D () () () () C C C FRONT C FT " 0" FT " " FT 0" " 0FT " " FITTINGS A - MJ-MJH 0 - BULKHEAD A - /" HN- LOCK NUT B - MB-MJ 0º ELBOW C - /" PIONEER TIP D - /" MJ-FJX 0 - ELBOW REQ'D () - ON MANIFOLD () - ON MANIFOLD () () () FT " 0" FT " " NOTE: HOSES # AND # ARE FJX-FJX NOTE: FITTING "D" ON THE TONGUE IS FOR FOLDING UNITS ONLY () - Fax () -

HYDRAULIC DIAGRAM FOR UNITS WITH TRANSPORT OPTION REAR OF THE MACHINE A A # # TRANSPORT WHEEL AXLE B # D B # D HYDRAULIC CYLINDERS () X0 TIE ROD CYL. HYD. LINE " LONG HYD.

26 HYDRAULIC DIAGRAM FOR UNITS WITH TRANSPORT OPTION REAR OF THE MACHINE A A # # TRANSPORT WHEEL AXLE B # D B # D HYDRAULIC CYLINDERS () X0 TIE ROD CYL. HYD. LINE " LONG HYD. LINE " LONG # # C C FRONT HOSES # - FJX-FJX " LONG # - FJX-FJX " LONG # - MP-MJ 0" LONG REQ'D () () () FITTINGS A - MB-MJ 0º ELBOW 000# CAP. B - MJ-MJ-MBT- TEE C - /" PIONEER TIP D - MJ-MJ 0º ELBOW REQ' () () () () () - Fax () -

27 T.G. SCHMEISER CO., INC. Limited Warranty Statement T. G. Schmeiser Co., Inc. warrants each new Schmeiser product to be free from defects in material and workmanship. This warranty is applicable only for the normal service life expectancy of the product or components, not to exceed twelve () consecutive months from the date of delivery of the new Schmeiser product to the original purchaser. Genuine T. G. Schmeiser Co., Inc. replacement parts and components will be warranted for 0 days from date of purchase, or the remainder of the original equipment warranty period, whichever is longer. Under no circumstances will it cover any merchandise or components thereof, which, in the opinion of the company, has been subjected to misuse, unauthorized modifications, alteration, an accident or if repairs have been made with parts other than those obtainable through T. G. Schmeiser Co., Inc. The Company in no way warrants engines, batteries, cylinders, tires or other trade accessories since these items are warranted separately by their respective manufacturer. Expendable components such as points, shanks, blades, rings, bearings, teeth, and the like are excluded from this warranty. Our obligation under this warranty shall be limited to repairing or replacing, free of charge to the original purchaser, any part that, in our judgment, shall show evidence of such defect, provided further that such part shall be returned within thirty (0) days from date of failure to T. G. Schmeiser Co., Inc., routed through the dealer and distributor from whom the purchase was made, transportation charges prepaid. This warranty shall not be interpreted to render T. G. Schmeiser Co., Inc. liable for injury or damages of any kind or nature to person or property. This warranty does not extend to the loss of crops, loss because of delay in harvesting, or any expense or loss incurred for labor, substitute machinery, rental or for any other reason. Except as set forth above, T. G. Schmeiser Co., Inc. shall have no obligation or liability of any kind on account of any of its equipment and shall not be liable for special or consequential damages. T. G. Schmeiser Co., Inc. makes no other warranty, expressed or implied, and, specifically, T. G. Schmeiser Co., Inc. disclaims any implied warranty or merchantability or fitness for a particular purpose. Some states or provinces do not permit limitations or exclusions of implied warranties or incidental or consequential damages, so the limitations or exclusion in this warranty may not apply. This warranty is subject to any existing conditions of supply, which may directly affect our ability to obtain materials or manufacture replacement parts. T. G. Schmeiser Co., Inc. reserves the right to make improvements in design or changes in specifications at any time, without incurring any obligation to owners of units previously sold. No one is authorized to alter, modify or enlarge this warranty nor the exclusion, limitations and reservations. WARRANTY VOID IF NOT REGISTERED WITHIN 0 DAYS OF PURCHASE DATE

28 Schmeiser Finishing Scraper Maintenance & Repair Record Date of Service or Repair Performed Parts Service Replaced

SCHMEISER PRECISION FINISHING SCRAPER 10 FT. to 24 FT. WIDE

SCHMEISER PRECISION FINISHING SCRAPER 0 FT. to FT. WIDE ASSEMBLY & PARTS MANUAL T.G. SCHMEISER CO., INC. P.O. BOX 0 () - FRESNO, CA FAX () - VERSION.a OCTOBER 0 COPYRIGHT 0 T.G.SCHMEISER CO., INC. INTRODUCTION