FRAME. Pull Type Rigid Frame, Lift Rotate INNER HITCH
|
|
- Mitchell Wilkerson
- 5 years ago
- Views:
Transcription
1 Pull Type Rigid Frame, Lift Rotate INNER HITCH The hitch length can be adjusted in 15" increments to accommodate the tractor tire options (single or dual tires) being used and attachments installed on the planter. The hitch consists of a rear section of 7" square tube and a front section of 6" square tube. To adjust the length, lower the machine to the field position and block the transport wheels. Support the 7" square tube with a minimum 5000 pound rated jack to take the weight off the 6" square tube. Remove the 1 1/4" x 9" hex head cap screw, loosen the two 5/8" hex head cap screws on the front end of the 7" square rear section and reposition the 6" square front section to the desired length. CAUTION: DO NOT set the hitch so short that turning ability is limited when the machine is in road transport position. Reinstall and tighten hardware to specified torque values. ITEM PART No. DESCRIPTION ITEM PART No. DESCRIPTION 1 KA8699 Inner Hitch, 65 1/4" 6 KB0156 Clevis 2 K10169 Hex Head Cap Screw, 1 1/4"-7 x 6" 7 See Outer Hitch K10157 Lock Nut, 1 1/4"-7 8 KA4774 Safety Chain, 3/8" 3 KD16328 Hose Holder K1K411 Safety Chain Repair Kit, Includes Hook, Flat 4 K10217 Washer, 5/8" USS Safety Latch, Spring And Retaining Ring K10230 Lock Washer, 5/8" 9 K11058 Hex Head Cap Screw, 1 1/4"-7 x 3" K10104 Hex Nut, 5/8"-11 K10226 Washer, 1 1/4" SAE 5 KA4994 Jack Assembly Complete KD10646 Special Washer KA4995 Detent Pin Assembly K10157 Lock Nut, 1 1/4"-7 KR0517 Pin 10 KA10709 Inner Hitch, 65 1/4", 7 1/2" Offset KR0516 Crank Assembly 11 K10717 Hex Head Cap Screw, 1 1/4"-7 x 9" KR0515 Bevel Gear K10236 Lock Washer, 1 1/4" K10239 Hex Nut, 1 1/4"-7 Rev 03/
2 Pull Type Rigid Frame, Lift Rotate OUTER HITCH OUTER HITCH ITEM PART DESCRIPTION Rev 03/
3 Pull Type Rigid Frame, Lift Rotate 1 K10006 Hex Head Cap Screw, 5/8"-11 x 2 1/4" KD7805 Special Washer, 5/8", Hardened KB0218 Bushing, 21/32" I.D. x 7/8" O.D. x 19/32" Long K10107 Lock Nut, 5/8"-11 2 KA6422 Catch Bar 3 KD5857 Spring 4 K10765 Spring Pin, 1/4" x 1" 5 KA6420 Transport Catch 6 KD4743 U-Bolt, 3" x 3" x 1/2"-13 K10228 Lock Washer, 1/2" K10102 Hex Nut, 1/2"-13 7 See Hydraulic System 8 See Transport Latch Cylinder 9 KA7022 Detent Pin W/Chain 10 K10061 Hex Head Cap Screw, 3/8"-16 x 3 1/2" K10229 Lock Washer, 3/8" K10101 Hex Nut, 3/8" KD Sleeve, 2" Long KD Sleeve, 5/8" I.D. x 7/8" O.D. x 1 15/16" Long (As Required) 12 KD7137 Pin, 3/4" x 3 3/8" K10457 Cotter Pin, 5/32" x 1 1/2" 13 KD0776 Hose Clamp, 3/4" x 2" x 2 1/2" 14 K10027 Hex Head Cap Screw, 3/4"-10 x 2 1/2" KD2169 Special Washer, 25/32" I.D. x 1 1/4" O.D., Hardened K10105 Hex Nut, 3/4" See Selector Valve, 16 K10716 Hex Head Cap Screw, 3/4"-10 x 1" K10231 Lock Washer, 3/4" KD2169 Special Washer, 25/32" I.D. x 1 1/4" O.D., Hardened 17 K10005 Hex Head Cap Screw, 5/8"-11 x 1 3/4" KD7805 Special Washer, 5/8", Hardened K10230 Lock Washer, 5/8" K10104 Hex Nut, 5/8" K10005 Hex Head Cap Screw, 5/8"-11 x 1 3/4" K10205 Washer, 5/8" SAE K10230 Lock Washer, 5/8" K10104 Hex Nut, 5/8" KA6371 Outer Hitch, 125 1/2" 20 K10004 Hex Head Cap Screw, 3/8"-16 x 1 1/4" K10108 Lock Nut, 3/8" KD10731 Wire Clamp (If Applicable) 22 K10004 Hex Head Cap Screw, 3/8"-16 x 1 1/4" K10229 Lock Washer, 3/8" K10101 Hex Nut, 3/8" K10939 Hex Head Cap Screw, 3/8"-16 x 2 1/4" K10108 Lock Nut, 3/8" KD16341 Hose Clamp, 3 3/4" x 6" 25 KA11201 Bulkhead Mount 26 K10228 Lock Washer, 1/2" K10102 Hex Nut, 1/2" KA6608 Cable Assembly 28 KD14106 Channel 29 KD Hose Protector, 48" 30 KD5875 Hose Clamp, 9/16" x 2 1/2" x 2" 31 KD0740 Hose Clamp, 3/4" x 4" x 3 1/2" 32 KD5892 Hose Clamp, 5/8" x 1 1/2" x 1 1/2" 33 K10108 Lock Nut, 3/8" KA6404 Jack Storage Mount 35 KA6623 Transport Post, 6 Row 30" KA6418 Transport Post, 8 Row 30" (Shown) 36 K10111 Lock Nut, 1/2"-13 Rev 03/
4 Pull Type Rigid Frame, Lift Rotate FRAME ASSEMBLY Pull-Type Rigid Frame with a Rotating main frame for transport with hydraulic operation. ITEM PART No. DESCRIPTION ITEM PART No. DESCRIPTION 1 KA9840 Light Bracket 10 K10022 Hex Head Cap Screw, 1/4"-20 x 1/2" 2 KD1113 U-Bolt, 5" x 7" x 5/8"-11 K10227 Lock Washer, 1/4" K10230 Lock Washer, 5/8" K10103 Hex Nut, 1/4"-20 K10104 Hex Nut, 5/8" K10019 Hex Head Cap Screw, 5/16" -18 x 1" 3 KB0309 Light Mount Bracket K10232 Lock Washer, 5/16" 4 K10874 Detent Pin, 1/2" x 3 1/2" Grip K10106 Hex Nut, 5/16"-18 5 K10033 Hex Head Cap Screw, 1/2"-13 x 3 1/2 12 See Electrical Components K10206 Washer, 1/2" SAE 13 K10064 Hex Head Cap Screw, 1/4"-20 x 1" K10111 Lock Nut, 1/2"-13 K10227 Lock Washer, 1/4" 6 See stickers K10103 Hex Nut, 1/4"-20 7 KA6401 Frame, 180", 6 Row 30" K10110 Lock Nut, 1/4"-20, Grade B KA9402 Frame, 188", 6 Row 30" K10312 Carriage Bolt, 5/16"-18 x 3/4" KA6364 Frame, 240", 8 Row 30" 14 K10620 Serrated Flange Nut, 5/16"-18 KA9401 Frame, 248", 8 Row 30" 8 KD6783 Bracket 9 See Row Marker Assembly Rev 03/
5 Pull Type Rigid Frame, Lift Rotate FRAME ASSEMBLY ITEM PART No. DESCRIPTION ITEM PART No. DESCRIPTION 15 KD15950 Light Mount Extension 31 K10172 Hex Head Cap Screw, 3/8"-16 x 5" 16 KD12724 Bracket K10108 Lock Nut, 3/8" K10037 Hex Head Cap Screw, 1/2"-13 x 1 1/4" 32 KD9971 Manifold Block K10228 Lock Washer, 1/2" 33 KR0375 Pin, 1" x 3 1/2" K10102 Hex Nut, 1/2"-13 KR0193 Hair Pin Clip 18 KA5121 Pin, 2 1/8" 34 KB Adjustment Plug 19 See Lift Cylinder 35 KB Cap 20 See Hydraulic System 36 K10014 Hex Head Cap Screw, 1/2"-13 x 1" 21 KD9093 Poly Wear Pad 37 See Row Marker Sequencing 22 KA6850 Valve Mount 38 K10025 Hex Head Cap Screw, 3/4"-10 x 1 1/2" 23 K10120 Hex Socket Set Screw, 3/8"-16 x 1/2" K10231 Lock Washer, 3/4" 24 K10005 Hex Head Cap Screw, 5/8"-11 x 1 3/4" 39 KD9052 Special Washer, 3/4" I.D. x 2" O.D., Hardened 25 K10638 Hex Head Cap Screw, 1/4"-20 x 2" 40 KD10532 Sleeve K10103 Hex Nut, 1/4" KA6497 Cam Follower W/Grease Fitting 26 KD10129 Mounting Bracket K10640 Grease Fitting, 1/4" See Stroke Limiter Valve 42 KD13250 SMV Bracket 28 K10048 Hex Head Cap Screw, 3/8"-16 x 2" 43 K11159 T-Bolt Clamp, 3 1/2", Stainless Steel K10101 Hex Nut, 3/8" KD16046 Bracket 29 KA7153 Stroke Limiter Arm 30 K10403 Hex Head Cap Screw, 1/4"-20 x 2 1/2" K10227 Lock Washer, 1/4" Rev 03/
6 FRAME Pull-Type Rigid Frame, Lift & Rotate HYDRAULIC OPERATION This planter is equipped for operation from two dual remote hydraulic outlets (SCV). One set of outlets is used to raise and lower the planter and one set is used to operate the markers and fold functions. A hand operated selector valve on the hitch allows selection of marker or fold functions. RAISED FIELD POSITION Safety Lockup Pin Stroke Limiter Valve DANGER: To avoid serious injury or death, care must be taken when operating row markers around overhead power lines. NOTE: Release hydraulic pressure from the system before moving the selector handle. PLANTER LIFT SYSTEM OPERATION The planter lift system consists of one lift cylinder located at the center of the machine. Mounts for this cylinder are located ahead and behind the center post. For planters with rear mounted row units only, the cylinder may be installed in the rear position. For planters with front mounted options (push row units, fertilizer, etc.), the cylinder must be installed in the front position. NOTE: The planter lift cylinder is equipped with a counter balance valve. Hydraulic pressure is required to lower the planter. Counter Balance Valve There are two raised positions on the planter. The first position is with the safety lockup pin installed above the frame assembly to make contact with the stroke limiter valve. This will allow the row units to raise approximately 14 inches off the ground and the toolbar approximately 40 inches. This position is used in making turns or passing over waterways during field operation. RAISED TRANSPORT POSITION The second raised position is the raised transport position. In this position the planter is allowed to raise high enough to permit the row units to clear the transport wheels as the planter is rotated. To raise the planter to the raised transport position: (1) Remove the safety lockup pin. (2) Raise the planter until the lift cylinder is fully extended. (3) Reinstall the safety lockup pin in the same hole which is now below the frame assembly. (4) Lower planter onto safety lockup pin. DANGER: Never work under the planter while in raised position without installing safety lockup devices Rev. 03/08
7 Pull Type, Rigid Frame Lift Rotate AXLE & PIVOT WHEEL ASSEMBLY ITEM PART NoDESCRIPTION 1 Rear Trailer Hitch 2 GA7543 Center Post 3 GA6849 Lockup Pin, 17 1/4" G10671 Spring Pin, 3/16" x 3 1/4" G10606 Spring Pin, 1/4" x 2" 4 GA6529 Rock Guard (Optional) 5 G10037 Hex Head Cap Screw, 1/2"-13 x 1 1/4" G10228 Lock Washer, 1/2" G10102 Hex Nut, 1/2"-13 6 GA6435 Bearing ITEMPART No. DESCRIPTION 7 G10028 Hex Head Cap Screw, 3/4"-10 x 3" 16 GD12543 Scraper GD2169 Spcl Washer, 25/32" I.D. x 1 1/4" O.D. 17 G10636 Carriage Bolt, 1/2"-13 x 1 1/2" G10105 Hex Nut, 3/4"-10 G10216 Washer, 1/2" USS 8 GD9122 Shim,.005" Thick G10228 Lock Washer, 1/2" GD9123 Shim,.007" Thick G10102 Hex Nut, 1/2"-13 GD9124 Shim,.020" Thick 18 G10008 Hex Head Cap Screw, 5/8"-11 x 2" 9 GD3389 Tap Block G10230 Lock Washer, 5/8" GD3398 Shim, 16 Gauge 19 GD9051 Bearing Cap GD7888 Shim, 22 Gauge 20 GD9130 O-Ring 10 G10016 Hex Head Cap Screw, 1/2"-13 x 2" 21 G10026 Hex Head Cap Screw, 3/4"-10 x 2" G10228 Lock Washer, 1/2" G10231 Lock Washer, 3/4" 11 GA6496 Bearing housing w/cups,w/o Grease Fit 22 GA4693 Spindle W/Round External Retaining Ring, 10 1/2" GD9121 Cup GD11490 Round External Retaining Ring G10779 Grease Fitting, 90, 1/4" GA0895 Bearing 12 GR0375 Pin, 1" x 3 1/2" 24 GR0270 Lug Bolt, 9/16"-18 GR0193 Hair Pin Clip 25 GA2148 Hub W/Cups, 6 Bolt 13 See Rotation Cylinder GR0434 Cup 14 A7380 Axle W/Stub And Scraper Mounts 26 G11081 Hex Jam Nut, 1 1/2"-12, Grade 2 15 G10027 Hex Head Cap Screw, 3/4"-10 x 2 1/2" 27 GA2142 Rim, 5.50" x 20" G10231 Lock Washer, 3/4" 28 GD13401 Tire, 7.50" x 20", 8 Ply, Tubeless W/O Center Rib G10105 Hex Nut, 3/4"-10 GA7434 Valve Stem A. GA6428 Hub And Spindle Assembly (Items 22, 23, 25 And 26) Rev 03/
8 Pull-Type Rigid Frame, Lift Rotate CONTACT DRIVE WHEEL The contact drive system is a spring-loaded contact drive tire (4.10 x 6") with No. 40 chain. There is one contact drive wheel on a 4- row planter; two on the 6-row, 8-row, and 12-row; and four contact drive wheels on the 16-row and the 24-row planters. There are 2 down pressure springs on each contact drive wheel. The down pressure is factory preset and should not need further adjustment. The spring tension is set leaving 1 1/2" between the spring plugs and the bolt head. Tire pressure should be checked regularly and maintained as follows, Contact drive: 4.1" x 6" -50 PSI Transport / Ground Drive: 7.5" x 20" -40 PSI. See PREPARING THE PLANTER for information on Lubrication or replacement of the Wheel Bearings. DANGER: Rim and tire servicing can be dangerous. Explosive separation of tire and rim parts can cause serious injury or death. See SAFETY section. ASSEMBLY Rev. 12/
9 Pull-Type Rigid Frame, Lift Rotate CONTACT DRIVE WHEEL ASSEMBLY ITEM PART No. DESCRIPTION 1 2 KD7426 Driveline Sprocket, 12 Tooth 3 KD1026 Sleeve, 1 3/16" Long 4 KA5157 Idler Arm, L.H. 5 KD5827 Cover 6 KD5857 Spring 7 K10312 Carriage Bolt, 5/16"-18 x 3/4" K10232 Lock Washer, 5/16" K10106 Hex Nut, 5/16"-18 8 K Flangette 9 K Bearing, 7/8" Hex Bore, Spherical 10 KA8925 Mount 11 K10004 Hex Head Cap Screw, 3/8"-16 x 1 1/4" K10229 Lock Washer, 3/8" K10370 KD5756 Machine Bushing, 3/8", 22 Gauge Special Nut, 3/8" KB0218 Bushing, 21/32" I.D. x 7/8" O.D. x 19/32" Long 13 KA7369 Wheel Arm (Non-Stock Item)(Sub G1K253) 14 K10306 Carriage Bolt, 3/8"-16 x 2" K10210 Washer, 3/8" USS K10108 Lock Nut, 3/8" K10004 Hex Head Cap Screw, 3/8"-16 x 1 1/4" K10229 Lock Washer, 3/8" K10101 Hex Nut, 3/8" K10751 Hex Head Cap Screw, 5/8"-18 x 1 3/4" K10235 KD7805 Machine Bushing, 7/8", 14 Gauge Special Washer, 5/8", Hardened K10412 Lock Nut, 5/8" KA2068 Spring W/Plug 18 K10501 Hex Jam Nut, 1/2"-13, Grade 2 19 K3310 Chain, No. 40, 116 Pitch Including Connector Link KR0912 Connector Link, No KA5105 Sprocket, 15 Tooth KA5107 Sprocket, 19 Tooth 21 K10602 Spring Pin, 1/4" x 1 1/2" 22 KD6825 Hex Shaft, 7/8" x 10 3/8" (2 Holes) 23 K10233 Machine Bushing, 1", 10 Gauge 24 KA9846 Flanged Bearing, 7/8" Hex Bore 25 K10890 Hex Head Adjusting Bolt, 1/2"-13 x 4", Grade 2 26 KA5090 Tire And Rim Assembly (Specify Brand*) KD5753 Tire, 4.10" x 6" (Specify Brand*) KD5752 Inner Tube 27 KD2558 Lynch Pin, 1/4" 28 K10303 Carriage Bolt, 5/16"-18 x 1" K10232 Lock Washer, 5/16" K10106 Hex Nut, 5/16"-18 A. K1K253 Contact Wheel Arm Replacement Kit (Items 13, 18, 21, 22, 24, 25, 27 and 28 Rev. 12/
10 _ Pull Type, Rigid Frame TRANSPORT WHEEL Tire pressure should be checked regularly and mainained as follows, Transport/Ground Drive 7.5" x 20" -40 PSI. For information on bearings, see PREPARING THE PLANTER. Due to the clearance between the wheel assembly and the transport tire, a tire scraper should always be used. The tire scraper will prevent a buildup of dirt and mud between the wheel arm assembly and the tire. Adjust the scraper so it does not contact the tire. Ridge Planting For ridge planting, to raise the bar height 3", mount the 20" tires in the lower rear holes in the ground drive wheel arm and springs in the lower set of mounting holes in the wheel module mount and raise the hitch height to mainain a level position from side to side and front to back. ASSEMBLY ITEM PART No. DESCRIPTION 1 K10009 Hex bolt 5/8-11 x 2 1/2 K10230 Lock washer 5/8 K10104 Hex nut 5/ KA5122 Wheel tower clamp 3 K10008 Hex bolt 5/8-11 x 2 KD7805 Special washer K10230 Lock washer 5/8 K10104 Hex nut 5/ See Hydraulic cylinders 5 KD5841 Pin 1 1/4" x 5 5/8" KD10460 Cotter pin 1/4 x 2 6 KA7376 Scraper mount 7 KD10010 Scraper 8 K11081 Hex jam nut 1 1/ KA0895 Bearing 10 KA2148 Hub with cups pressed in KR0434 Bearing cup 11 KR0270 Lug bolt 9/ KA2558 Spindle w/retaining ring KD11490 Retaining ring 13 KD13401 Tire 7.50 x 20, 8 ply 14 KA2142 Rim 5.50 x KA7434 Valve stem 16 K10025 Hex bolt 3/4-10 x 1 1/2 K10231 Lock washer 3/4 ITEM PART No. DESCRIPTION K10105 Hex nut 3/ K10581 Hex bolt 1/2-13 x 2 1/4 17 K10026 Hex bolt 3/4-10 x 2 K10111 Lock nut 1/2-13 K10231 Lock washer 3/4 22 KA5121 Pin 2 1/8" 18 K10636 Carriage bolt 1/2-13 x 1 1/2 23 KA8839 Arm K10228 Lock washer 1/2 24 KD11695 Pin 1 1/4" x 13 1/4" K10216 Washer 1/2 25 K10610 Spring pin 3/8 x 2 K10102 Hex nut 1/ KA9877 Clamp w/grease fittings 19 K10139 Washer 1 1/4 K10640 Grease fitting 1/ K10159 Bushing 1 1/4 x 10GA KA2147 Hub and Spindle asm (Items 8-10 and 12) Rev. 12/
11 _ Pull Type Rigid Frame, Lift and Rotate DRIVELINE ASSEMBLY ITEM PART No. DESCRIPTION 1 KD1256 Spring 2 KD1255 L-Pin 3 KA5165 Sprocket, 30 Tooth 4 K10464 Cotter Pin, 3/16" x 1" 5 KA0378 Block And Hub Assembly 6 K10430 External Retaining Ring, 1 1/4" 7 KD9078 Hex Shaft, 7/8" x 58" (4 Holes), 6 Row 30" KD9077 Hex Shaft, 7/8" x 98" (4 Holes), 8 Row 30" 8 KB0287 Coupler 9 KD Hex Shaft, 7/8" x 165" (No Holes), 6 Row 30" KD Hex Shaft, 7/8" x 225" (No Holes), 8 Row 30" 10 K10131 Square Head Set Screw, 5/16"-18 x 3/4" 11 K10130 Square Head Machine Bolt, 5/16"-18 x 1 3/4" K10923 Flange Nut, 5/16"-18, No Serration 12 KD11045 Lock Clamp A KA5164 Ratchet/Sprocket Assembly (Items 1-6) B K1K269 Lock Clamp Kit (Items 11 And 12) Rev. 03/
OPERATOR S MANUAL MAINTENANCE MANUAL PARTS LIST TURFCO. 60 Inch Seeder. Product Number Starting Serial Number H00801 PATENT PENDING
0 Inch Seeder OPERATOR S MANUAL MAINTENANCE MANUAL PARTS LIST TURFCO 0 Inch Seeder Product Number 0 Starting Serial Number H000 PATENT PENDING Manual Number DANGER - IF INCORRECTLY USED THIS MACHINE CAN
More information3. FRAME 1. SAFETY 2. PREPARATION 4. TRANSMISSION 5. DRIVE 6. ROW UNIT 7. OPTIONAL EQUIPMENT Monosem Inc.
TABLE OF CONTENTS 1. SAFETY 2. PREPARATION 3. FRAME 4. TRANSMISSION 5. DRIVE 6. ROW UNIT 7. OPTIONAL EQUIPMENT FRAME 7" x 7" Twin-Row Frame, Rigid For 4 x 2 row Frames The Twin-row frames are rigid and
More informationParts Manual. Field-Pro Heavy Harrow Bar. Part Number H
Parts Manual Field-Pro Heavy Harrow Bar Part Number H28542-04 IMPORTANT: ALL ITEMS ARE IDENTIFIED WITH A PART NUMBER. Some of the smaller parts such as bolts, nuts, washers, etc. are not all shown, however,
More informationHR24TS Rotary Rake. Serial Numbers less than Illustrated Parts Breakdown. Curtain & Guards, Front
HRTS Rotary Rake Serial Numbers less than 00 Illustrated Parts Breakdown Page Page Page Page Page Page Page Page Page Page Page Page Tongue Front Frame Front Axle Curtain & Guards, Front Front Pivot Bridge
More informationCOMMERCIAL MOWERS PARTS MANUAL FOR: MODELS: ZKH52221 ZKH52251 ZKH61221 ZKH61251
PARTS MANUAL FOR: COMMERCIAL MOWERS MODELS: ZKH52221 ZKH52251 ZKH61221 ZKH61251 FD KEES POWER EQUIPMENT, L.L.C. 700-800 PARK AVENUE BEATRICE, NEBRASKA, U.S.A. 68310 PRINTED IN USA MANUAL NO.-102935 REV.
More informationParts Manual for: MODELS / I.D. : / ZTH5223A / ZTH5225A / ZTH6125A
Parts Manual for: MODELS / I.D. : 968999153 / ZTH5223A 968999154 / ZTH5225A 969999155 / ZTH6125A Husqvarna policy is to improve its products whenever it is possible and practical to do so. In an effort
More informationW & A PARTS MANUAL STACKER BUSTER LEVEL BANDER. Model No Quality Products from W & A MANUFACTURING COMPANY
W & A PARTS MANUAL 12 ROW @ 38 STACKER BUSTER LEVEL BANDER Model No. 3668 SPECIALIZED FARM EQUIPMENT Quality Products from W & A MANUFACTURING COMPANY P.O. Box 5238, Pine Bluff, Arkansas 71611 Phone: (870)
More informationParts Manual for MODELS: ZKH52222 ZKH52252 ZKH61252
Parts Manual for MODELS: ZKH52222 ZKH52252 ZKH61252 Professional Quality Lawn Care Equipment since 1945 THIS MANUAL INCLUDES UPDATES ON PAGES 6,10, & 20. Yazoo/Kees Power Equipment policy is to improve
More informationTable of Contents. Section H : Gauge Wheels & Mesh Roller. Section H. Call or Northwest Tillers today
Table of Contents Section H Section H : Gauge Wheels & Mesh Roller 6½ Gauge Wheel (SRB4098)... H1 9½ Gauge Wheel (SRB4099)... H2 6½ & 9½ Gauge Wheel Hubs... H3 Heavy Duty Gauge Wheel (SRB4070 & SRB4076)...
More information00278 R1 AXLE, FOR 1-1/8" FREE WHEEL HUBS
00 ACTUATOR VALVE, O-RING PORTS 00 C-CLIP, /" 00 SPRING, VALVE SPOOL RETURN 00 COLLAR, / ID 00 WASHER, / USS, ZINC 00 HH CAP SCREW, /- NC X -/ G ZINC 0 FITTING, 0-- 00 O-RING, - FITTING 000-BO RELIEF VALVE,
More informationEMB MANUFACTURING INC.
TRAILER WOOD PROCESSOR MODELS WP865, WP835, WP635 ASSEMBLY INSTRUCTION MANUAL Please review and understand the operators manual before attempting to operate this machinery. EMB MANUFACTURING INC. 4144
More informationParts Manual 881 Hay Hiker
Parts Manual 881 Hay Hiker Part Number K20393P-06 IMPORTANT: ALL ITEMS ARE IDENTIFIED WITH A PART NUMBER. Some of the smaller parts such as bolts, nuts, washers, etc. are not all shown, however, the quantity
More informationIllustrated Pats List
Illustrated Pats List Automatic Lawn Tractor Models 0 0 0 Model 0 Shown IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning: This unit is equipped with an internal combustion engine and should
More informationELSTON. Gopher Getters. Parts List for GA-400 and GA-500 ELSTON MANUFACTURING INC. Please Contact Us for Parts and Service:
ELSTON Gopher Getters Parts List for GA-00 and GA-00 Another Quality Product of: Please Contact Us for Parts and Service: ELSTON MANUFACTURING INC. 70 N Weber Sioux Falls, SD 70 www.elstonmfg.com -800-8-8
More informationMANUFACTURING INC. 706 N
ELSTON Gopher Getters Parts List for GA-00 & GA-00 Please Contact Us for Parts and Service: Another Quality Product of: ELSTON MANUFACTURING INC. 70 N Weber Sioux Falls, SD 70 www.elstonmfg.com -800-8-8
More informationParts Manual 2200 Bale Hiker
Parts Manual 2200 Bale Hiker Part Number K56202-02B IMPORTANT: ALL ITEMS ARE IDENTIFIED WITH A PART NUMBER. Some of the smaller parts such as bolts, nuts, washers, etc. are not all shown, however, the
More informationInspection. Assembly Install the springs. 1. Discard the 0-rings. 2. Clean all parts in cleaning solvent.
6010-34 Inspection 3. Install the springs. 1. Discard the 0-rings. 2. Clean all parts in cleaning solvent. 3. If spring test equipment is available, check the tension of each spring according to the specifications
More informationSection A Gear Box September A
Section A Gear Box September 06 1A Index 1. 1-10016-000 Gear Box Oil Pan. 1-100486-000 Clutch Lever Assembly, See Page 9A for breakdown. 1-1004-000 Clutch Cam, for all A machines prior to Serial #5 1-104-000
More information767, 777, DC-10, L-1011, MD-11 Tow Bar Equipment Manual
514 MECKLEM LANE, ELLWOOD CITY, PENNSYLVANIA 16117 www.hallindustries.com E-mail: service@hallindustries.com 767, 777, DC-10, L-1011, MD-11 Tow Bar Equipment Manual Use This Manual for 1. Operating Procedures
More informationIllustrated Parts Manual
Illustrated Parts Manual Mustang Series RZT TROY-BILT LLC, P.O. BOX CLEVELAND, OHIO -00 Printed In USA Form No. -0 (December, 0) To The Owner Thank You Thank you for purchasing an MTD Zero-Turn Tractor.
More informationMMZ jr Hydrostatic Zero-Turn Riding Mower
MMZ jr. Hydrostatic Zero-Turn Riding Mower MODEL ABM HP " Stamped Deck ILLUSTRATED PARTS LIST TABLE OF CONTENTS " Cutter Deck............................. and " Spindle Assembly.........................
More informationOPERATOR'S MANUAL 46" SNOW BLADE. Model Numbers OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
OPERATOR'S MANUAL 46" SNOW BLADE Model Numbers 190-833-OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722 PRINTED IN U.S.A. FORM NO.
More informationTire Chain Kit. Replacing Shear Pins. Weight Kits. Drift Cutter
Replacing Shear Pins The augers are secured to the spiral shaft with two shear pins and cotter pins. If the auger should strike a foreign object or ice jam, the snow thrower is designed so that the pins
More informationParts Manual. Models 521 SSE (621502X37NA) 521 SSR (621503X37NA) &
Parts Manual Models 521 SSE (621502X37NA) 521 SSR (621503X37NA) 1740273 & 1740275 11.2006 Table Of Contents PRODUCT COMPONENTS PAGES Handle Group... 4 Engine Group... 6 Frame Group... 8 Auger Housing
More informationWarnings. Description. Prior to Installation Tools Needed
Warnings Failure to act in accordance with the following may result in death or personal injury. The JT Strong Arm Stabilizer System is intended to eliminate chassis movement in travel trailers and fifth
More informationN. 15th Street, Middlesboro, KY FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS
1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Dump Body tarping system. With tarping systems
More informationW & A PARTS MANUAL PTO POWER DITCHER FOR CAT. II OR III STANDARD & QUICK HITCH. Model No RPM Model No.
W & A PARTS MANUAL PTO POWER DITCHER FOR CAT. II OR III STANDARD & QUICK HITCH Model No. 360 -- 540 RPM Model No. 370 -- 1,000 RPM SPECIALIZED FARM EQUIPMENT Quality Products from W & A MANUFACTURING COMPANY
More informationHYDRAULIC MOWER AHRM4H, HRM48H Parts Catalog INDEX HOME TRACTOR ATTACHMENTS APPLICATION CHART
R Ingersoll HYDRAULIC MOWER AHRM4H, HRM48H Parts Catalog 8-3091 HOME TRACTORS ATTACHMENTS PAINT GENERAL INFO INDEX Deck. Belt and Idler Pulley...5 Mounting Bracket...7 Rear Wheels...7 Hydraulic Drive...9-13
More informationCHIPPER SHREDDER H524H, HS24W AHS24H, AHS24W Parts Catalog
R Ingersoll CHIPPER SHREDDER H524H, HS24W AHS24H, AHS24W Parts Catalog 8-3291 HOME TRACTORS ATTACHMENTS PAINT GENERAL INFO ALPHABETICAL Body, Hopper and Shredder Hammers...5 Chipper Assembly...7 Trailer
More informationSECTION 7 - SUSPENSION
For Arctic Cat Discount Parts Call 606-678-9623 or 606-561-4983 SECTION 7 - SUSPENSION TABLE OF CONTENTS Section Front and Rear Suspension Assembly Schematics... 7-2 Shock Absorbers... 7-4 Swing Arms (ACT
More informationHydrostatic Zero-Turn Commercial Riding Mower
Hydrostatic Zero-Turn Commercial Riding Mower Turf Equipment MODEL 20HP Enforcer 44 22HP Enforcer 48 23HP Enforcer 54 ILLUSTRATED PARTS LIST TABLE OF CONTENTS Frame Assembly..................................
More informationPARTS LIST MS 2892-D
PARTS LIST MS 89-D 8--00 8-0-000 KNIFE BRACE (TOP) 8--00 RIGHT KNIVE (UHMW) 8--00 LEFT KNIFE (UHMW) 8-0-00 KNIFE BRACE (UNDER) NC0-8-0 0 FLAT HEAD SOCKET CAP SCREW STAINLESS /8- X " LG NC0-9-00 0 LOCK
More informationATTACHMENT APPLICATION CHART
R Ingersoll RM42Y2, RM44YR2 MOWERS SB38Y2 SNOWCASTER UB38Y2 UTILITY BLADE BG42Y2 BAGGER Parts Catalog 8-3280 INDEX PAINT GENERAL INFO 2014 Tractor with RM42Y2 Mower and BG42Y2 Bagger ATTACHMENT APPLICATION
More informationLORON SERVICE MANUAL / PARTS LIST SINGLE DOUBLE PALLET HANDLER CONTENTS: PAGE 1 Lift Truck Requirements General Installation Procedures
LORON SERVICE MANUAL / PARTS LIST SINGLE DOUBLE PALLET HANDLER CONTENTS: PAGE 1 Lift Truck Requirements General Installation Procedures 2 Mounting Options Stop Block Adjustments 3 General Weekly Inspection
More informationMANUAL REV. 03 (11/26/01)
Parts Manual MANUAL 539105906 REV. 03 (11/26/01) Models: 968999175 / ZTH7226KOA 968999180 / ZTH5221KAA 968999181 / ZTH5223KAA 968999182 / ZTH5223KOA 968999183 / ZTH5223KOLA 968999184 / ZTH5225KOA 968999185
More informationIllustrated Parts List
Illustrated Parts List Rear Tine Tiller Model Series 0 Thru Model Series 0 Shown IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning: This unit is equipped with an internal combustion engine
More informationParts Manual 900 Hay Hiker
Parts Manual 900 Hay Hiker Part Number K49078-04 IMPORTANT: ALL ITEMS ARE IDENTIFIED WITH A PART NUMBER. Some of the smaller parts such as bolts, nuts, washers, etc. are not all shown, however, the quantity
More informationMODELS: CC3730TE / CC3740TE
DIAMOND P R O D U C T S CONCRETE SAW PARTS LIST MODELS: CC0TE / CC0TE February 00 Part #00 Table of Contents Pictorial Page Index....., Belt Guard Assembly... Controls Legend....... Belt Tensioner Assembly....
More informationIllustrated Parts & Packing List 528 Gandrud Road, Owatonna, MN For a complete distributor & dealer list go to
Illustrated Parts & Packing List 528 Gandrud Road, Owatonna, MN 55060 For a complete distributor & dealer list go to www.gandy.net 4927 Hydraulic Lift Package For Sweep Master (All Hardware In Hardware
More informationFLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS
1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Trailer system.
More informationTube-Line Baleliner 7800TX2
Tube-Line Baleliner 7800TX2 Parts Manual 29667 (13/04/12) 2 3 Frame Assembly 4 Frame Assembly Item Qty Part # Description 1 1 27298 E-Stop Button 2 8 28663 Outside Rail Pin 3 1 28805 Wire Shield 4 1 28823
More informationMODELS 920LS-922LS SERIES
THE MODELS 90LS-9LS SERIES HYDRAULIC LOG SPLITTER EXPLODED VIEWS WITH PART NUMBERS CONGRATULATIONS! You are now the proud owner of a BARRETO log splitter. The following pages have detailed views of your
More informationClick Here To View Item at
Click Here To View Item at www.gappower.com (Parts Pages Follow) ATTENTION If you need an Owner s/operator s Manual and/or safety signs (decals), then please contact Danuser. Provide your Model Number
More informationParts Manual SPEEDZTR 42 / SPEEDZTR 42BF / SPEEDZTR 46BF / SPEEDZTR 48BF / SPEEDZTR 54BF /
Parts Manual SPEEDZTR 42 / 6603801 SPEEDZTR 42BF / 66054201 SPEEDZTR 46BF / 658831 SPEEDZTR 48BF / 65883501 SPEEDZTR 54BF / 65883201 Please read the operator s manual carefully and make sure you understand
More information535A. Main Components. Pipe and Bolt Threading Machine. Printed in U.S.A. Ridge Tool Company/Elyria, Ohio, U.S.A.
Pipe and Bolt Threading Machine A Main Components 0 Screw, Button Head /" - 0 x /" () Washer, Flat /" ()" Top Cover 0 Base Bottom Cover Screw, Pan Head # - x " () Carriage Assembly 0 Front Support Bar
More informationREAD INSTRUCTIONS THOROUGHLY BEFORE USING MACHINE
OPERATING INSTRUCTIONS READ INSTRUCTIONS THOROUGHLY BEFORE USING MACHINE BEAD LOOSENING OPERAT ION LOOSEN BOTTOM BEAD FIRST Step 1. Remove the core from the tire valve and allow the pressurized air to
More information400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS
12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions
More informationCONCRETE SAW PARTS LIST
CONCRETE SAW PARTS LIST MODEL CC00XL ELECTRIC & HYDRAULIC UNITS August, 0 Part # 0 Table of Contents Common Parts.. Front Axle Assembly... Rear Axle Assembly... Transmission Assembly... Blade Shaft Assembly
More information00238 R4 BODY, BOLT ON TORQUE TUBE PRODUCT LINE: 916/18 DATE: 12/4/06
0 0 SH CAP SCREW, /-0 NC X / G PLAIN 00 NUT, NYLOCK, /-0 NC ZINC 00 HH CAP SCREW, /- NC X G ZINC 0 O-RING, -N0, -/ OD X / SECTION 00 WHEEL DRIVE MOTOR WITH KEY 0 00 GEAR, WHEEL DRIVE MOTOR 0 WASHER, /
More informationParts Manual RZ4623 /
Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. Parts Manual RZ4623 / 967009801 Please
More informationParts Manual SPDZTR 42 / SPDZTR 42 BF /
Parts Manual SPDZTR 42 / 966657601 SPDZTR 42 BF / 966657701 Please read the operator s manual carefully and make sure you understand the instructions before using the machine. Gasoline containing up to
More informationRotary Mower L47, M47, N47, RM44YR Parts Catalog
R Ingersoll Rotary Mower L47, M47, N47, RM44YR Parts Catalog 8-2711 HOME TRACTORS ATTACHMENTS PAINT GENERAL INFO ALPHABETICAL Axle... 9 Bearings, Spindles... 11-13 Belts... 5-7 Blades... 11-13 Bracket,
More informationINDEX. 52SD Mower Deck Shell, Pulley Covers, Gauge Wheels and Attaching Parts Pulleys, Blades, Belts, Spindles and Attaching Parts...
R Ingersoll HOME TRACTORS 52SD, 62SD and 72SD INDEX 52SD Mower Deck Shell, Pulley Covers, Gauge Wheels and Attaching Parts... 3 Pulleys, Blades, Belts, Spindles and Attaching Parts... 5 62SD Mower Deck
More informationSECTION 9: PARTS. Table Breakdown REF PART # DESCRIPTION REF PART # DESCRIPTION
SECTION 9: PARTS Table Breakdown 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 23 25 17 26 27 8 1 P0675001 CAP SCREW M8-1.25 X 30 15 P0675015 SUPPORT BLOCK 2 P0675002 TABLE SUPPORT BLOCK
More informationAPPLICATION CHART. Tractor Model * Wood Splitter HOME TRACTORS ATTACHMENTS INDEX
R Ingersoll HOME WOOD SPLITTER J31, K31 AHSHD, HSHD, J32, K32, J32 J34, K34, L34 AHSWD, HSWD, K36 Parts Catalog 8-2052 NOTE: This Catalog replaces Catalog 8-2051 TRACTORS ATTACHMENTS INDEX PAINT GENERAL
More informationWalk-Behind Lawn Mowers
Walk-Behind Lawn Mowers Parts Manual Models 2 - PRO21SCH 12 - LM21 1 - LM21S 1 - LM21SW 1 - LM21S 11 - PRO21SCH 0 - LM21SW - LM21S - LM21SW 5 - LM21S - LM21SW 0700 /0 Printed in USA THE MANUAL Before you
More information32 FRONT DECK ASSEMBLY
3 6 K 2 0 PARTS MANUAL 32 FRONT DECK ASSEMBLY 3 1 2 Belt Shield Prior to SN 33333 4 6 21 22 7 24 2 26 14 8 13 12 9 10 11 27 2 28 1 16 2 19 17 30 36 39 39 37 29 60 62 61 3 9 49 41 40 28 48 42 13 43 44 47
More informationGared Pro-S Portable Backstop
Models: 9616 & 9618 Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE USE PUBLICATION
More informationPower Train Lift Max. Capacity: 1,250 lbs.
655 EISENHOWER DRIVE OWATONNA, MN 55060 USA PHONE: (507) 455-7000 TECH. SERV.: (800) 533-6127 FAX: (800) 955-8329 ORDER ENTRY: (800) 533-6127 FAX: (800) 283-8665 INTERNATIONAL SALES: (507) 455-7223 FAX:
More information240 Owner s Manual & Parts Book
0 Owner s Manual & Parts Book Purchase Date Serial Number Model Number Tractor Model Dealer PN: 3-188 Serial #:083-88, 0, 07-... Date --0 Contents Description Page To The Owner, Maintenance Safety Precautions
More informationParts Manual 9s Series Air Cart
Parts Manual 9s Series Air Cart Part Number N58348-02 IMPORTANT: ALL ITEMS ARE IDENTIFIED WITH A PART NUMBER. Some of the smaller parts such as bolts, nuts, washers, etc. are not all shown, however, the
More informationPARTS LIST COMMANDER 20 VAC-TRAC COMMANDER 27 VAC-TRAC FH 541V
PARTS LIST COMMANDER 20 VAC-TRAC COMMANDER 27 VAC-TRAC FH 541V UPPER ASSEMBLY 101 6190481 THROTTLE CABLE FOR MODELS WITH ADDITIONAL CHOKE CABLE 1 101 6190751 THROTTLE CABLE FOR MODELS WITH OUT ADDITIONAL
More informationAPS Small Seeds Box Assembly Instructions
APS Small Seeds Box Assembly Instructions For APS15 Series All Purpose Seeder Manual No. 313-473M Before You Start! When you see this symbol, the subsequent instructions and warnings are serious - follow
More informationHYDRAULIC CONTROL DETAILS PARTS LIST
Always give model number, serial number and part number when ordering repair parts. HYDRAULIC CONTROL DETAILS PARTS LIST REF NO. PART NUMBER DESCRIPTION 1 101939 Hydraulic Tank 2 101940 Hydraulic Tank
More informationHD installation guide
JANUS INTERNATIONAL 1 866 562 2580 www.janusintl.c o m 1950 1950HD installation guide RIGHT DRIVE END SHOWN LH OPPOSITE LEFT TENSION END SHOWN RH OPPOSITE PUSH-UP OPERATION 1950 1950HD SHOWN A rolling
More informationPrecision Split Parts Manual
Precision Split Parts Manual Models 9700 7-Ton Log Splitter 9700 -Ton Log Splitter 086000B /09 Printed in USA THE MANUAL Before you operate your unit, carefully and completely read manuals supplied with
More informationEMB Manufacturing Inc Boomer Line St. Clements, On N0B 2M0 Canada Ph: (519) Fax: (519) P200
BY EMB MFG INC. EMB Manufacturing Inc. 4144 Boomer Line St. Clements, On N0B 2M0 Canada Ph: (519) 699-9283 Fax: (519) 699-4146 www.embmfg.com Available: P210 Spare Pivoting Chainsaw Adaptor See page 6
More informationMODEL 83 Pail Handler
MORSE MFG. CO., INC. 727 West Manlius Street P.O. Box 518 East Syracuse, NY 13057-0518 Phone: 315-437-8475 Fax: 315-437-1029 Email: service@morsemfgco.com Website: www.morsemfgco.com COPYRIGHT 2005 MORSE
More informationOWNERS MANUAL. Model No LB. POLY PRO SPIKER/SPREADER. CAUTION: Read Rules for Safe Operation and Instructions Carefully
OWNERS MANUAL Model No. -0301 CAUTION: Read Rules for Safe Operation and Instructions Carefully 17 LB. POLY PRO SPIKER/SPREADER Safety Assembly Operation Maintenance Parts PRINTED IN U.S.A. FORM NO. 78
More informationJARVIS. Model Brisket Scissor EQUIPMENT... TABLE OF
Model 423-17 Brisket Scissor EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page Model 423--17... 4037003 Air Filter / Regulator / Lubricator 3022003 Air Hose Assembly... 3059018 Balancer...
More informationParts Manual. English
Parts Manual WHF4817 / 966947005 WHF3617 / 966947008 Please read the operator s manual carefully and make sure you understand the instructions before using the machine. English 2009 HTC. All rights reserved.
More informationinstallation guide
JANUS INTERNATIONAL 1 866 562 2580 w w w. j a n u s i n t l. c o m 2000 2500 3000 installation guide RIGHT DRIVE END SHOWN LH OPPOSITE LEFT TENSION END SHOWN RH OPPOSITE PUSH-UP OPERATION 2000 2500 3000
More informationINSTALLATION INSTRUCTIONS
B E Fig. 1 A J INSTALLATION INSTRUCTIONS REESE Steadi-Flex K H 66557 250LB 400LB Weight Distributing Kits 66558 400LB 600LB G D C F A 1 BALL MOUNT B 1 DRAW BAR C 2 3/4-10 x 4-1/2" GR.8 HEX HEAD BOLT D
More informationSection F SETTING TABLE
Section F SETTING TABLE December 2009 1F Index No. Part No. Description 1. 47-051635-001 Geared Rack 2. 11-051880-001 N.A. Truss Hd. Machine Screw (6 mm x 16 mm) 47-861008-001 R.O. Truss Hd. Machine Screw
More informationBX62R Chipper Parts Manual. Prior to S/N 162R00282
Prior to S/N 162R00282 Foreword EMB Mfg. has prepared this parts manual to assist customers in ordering quality OEM replacement parts. Proper and regular service and replacing old, worn or broken parts
More informationCommercial Reel Mower
Commercial Reel Mower Parts Manual Models 00 CL- -Inch Kohler 0 CL- -Inch Honda 0 CL-0 0-Inch Kohler 0 CL-0 0-Inch Honda Gasoline containing up to 0% ethanol (E0) or up to 0% MTBE (methyl tertiary butyl
More informationTABLE OF CONTENTS DESCRIPTION. Safety Instructions Assembly Operation... 7
TABLE OF CONTENTS DESCRIPTION PAGE Warranty... 1 Safety Instructions... 2 Assembly... 3 Operation... 7 #360 Grain Cleaner Drawings... 8 #360 Grain Cleaner Parts List... 10 Utility Auger Option Drawing...
More informationIllustrated Parts List I Snow Thrower. 42 Inch Two Stage (LST42C) Repair Parts Manual
Illustrated Parts List 2008-01 I0807215 Snow Thrower 42 Inch Two Stage (LST42C) Repair Parts Manual owners manual Model No. LST42C 42" SNOW THROWER CAUTION: Read Rules for Safe Operation and Instructions
More informationSTONE EXTREME /29/2013 PART NUMBER
STONE EXTREME 700 PART NUMBER 005 STONEKOR LLC -800-6-059 customerservice@stonekor.com www.stonekor.com 9 0 6 0 6 5 0 8 6 5 7 STONE EXTREME 700 5 5 7 7 6 0 MACHINE: 005 5 5 8 7 8 9 0 9 STONEKOR LLC -800-6-059
More informationST927E Spare Parts
ST927E 1.1997 Spare Parts ELECTRIC START ASSEMBLY 8 9 7 6 ENGINE 6 601 00 15-88 MOTOR, STARTER 7 601 00 15-89 SCREW, 1/4-20X.50 8 601 00 15-90 SCREW, #6-32X2.50 9 601 00 15-91 CORD, STARTER 10 601 00 21-61
More informationMANUAL REV. 09 (04/20/06)
Parts Manual MANUAL 539105906 REV. 09 (04/20/06) Models: 968999175 / ZTH7226KOA 968999180 / ZTH5221KAA 968999181 / ZTH5223KAA 968999182 / ZTH5223KOA 968999183 / ZTH5223KOLA 968999184 / ZTH5225KOA 968999185
More information1822-I. Spindle Assembly. Pipe and Bolt Threading Machine. Ridge Tool Company/Elyria, Ohio, U.S.A. 2* 3 4 5* * *
-I Pipe and Bolt Threading Machine Spindle Assembly * * * 0 * * * 0 * * 0* * * Rear Cover * Screw () * Washer () Top Cover w/clips (Includes,, ) * J Clip () Front Cover * Screw () Pivot Rod Support ()
More informationZVKH52230 ZVKH61250 ZVKE61260 ZVKH61270 ZVKE72260 ZVKH72270 ZVKHL61230 ZVKW52250 ZVKW61230 ZVKW61250 MANUAL REV.
Parts Manual Models ZVKH52230 ZVKH61250 ZVKE61260 ZVKH61270 ZVKE72260 ZVKH72270 ZVKHL61230 ZVKW52250 ZVKW61230 ZVKW61250 MANUAL 106149 REV. 04 (10/09/02) Model Number: Serial Number: Date of Purchase:
More informationParts Manual TF Band Sawing Machine
Parts Manual TF-2525 Serial No: 356-07283 to Band Sawing Machine MACHINE SPECIFICATIONS MODEL VOLTAGE CYCLE PHASE SERIAL NO. For your information and future reference, insert pertinent data concerning
More informationSERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12" DUAL BEVEL COMPOUND MITER SAW B27B
PAGE 1 OF 6 BASE ASSEMBLY 00 0 EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS = Part number change from previous service
More informationOWNERS MANUAL. Model No UTILITY CART
OWNERS MANUAL Model No. 45-00 UTILITY CART CAUTION: Read Rules for Safe Operation and Instructions Carefully Assembly Operation Maintenance Repair Parts PRINTED IN USA FORM NO. 46274 LOOSE PARTS IN CARTON
More informationPrecision Split Parts Manual
Precision Split Parts Manual Model 917001 7-Ton Log Splitter 0860400 /09 Printed in USA THE MANUAL Before you operate your unit, carefully and completely read manuals supplied with the unit. The contents
More informationParts Manual for: MODELS / I.D. : / WH3614A / WH3615A / WH4817A
Parts Manual for: MODELS / I.D. : 968999105 / WH3614A 968999111 / WH3615A 968999106 / WH4817A Husqvarna policy is to improve its products whenever it is possible and practical to do so. In an effort to
More informationHopper and Drive Components
Western Products, PO Box 245038, Milwaukee, WI 53224-9538 www.westernplows.com September 1, 2015 Lit. No. 43772, Rev. 00 Hopper and Drive Components PRO-FLO 525 Low-Profile Tailgate Spreader Parts List
More informationCAPX Installation Print 4/10/ CAB ASSEMBLY Part Pos Description Quantity Foot Notes CAB SECTION PLATE, MO
CAPX Installation Print 4/10/2019 6245100014 CAB ASSEMBLY Part Pos Description Quantity Foot Notes 6245100008 1 CAB SECTION 1 + 6705100023 2 PLATE, MOUNTING 1 6705012439 3 PLATE, MOUNTING 1 6326100000
More informationW & A PARTS MANUAL 8 & 12 ROW FOLDING LEVEL BANDER. Model No & Quality Products from W & A MANUFACTURING COMPANY
W & A PARTS MANUAL 8 & 12 ROW FOLDING LEVEL BANDER Model No. 3628 & 3632 SPECIALIZED FARM EQUIPMENT Quality Products from W & A MANUFACTURING COMPANY P.O. Box 5238, Pine Bluff, Arkansas 71611 Phone: (870)
More informationPLOW ACCESSORIES PARTS MANUAL
RWF INDUSTRIES 873 Devonshire Ave., Woodstock, Ontario N4S 8Z4 Tel: (519) 421-0036 Toll Free: 1-800-263-1060 Fax: (519) 421-0028 Email: parts@rwfbron.com ACCESSORIES 2015 INDEX: PARTS & MAINTENANCE MANUAL
More informationINSTRUCTION MANUAL AND PARTS LIST MODEL 14-10
VERTICAL BAND SAWS INSTRUCTION MANUAL AND PARTS LIST MODEL 1-10 DAKE/PARMA WHEN ORDERING PARTS GIVE COMPLETE SERIAL NUMBER OF MACHINE GIVE PART NUMBER AND NAME GIVE AMOUNT REQUIRED Unless the above data
More information/ ZTH5225KAA / ZTH6125KAA / ZTH6123KOLA / ZTH6127KOB / ZTH7227KOB For Serial No & Higher
Parts Manual Models: 968999185 / ZTH5225KAA 968999186 / ZTH6125KAA 968999189 / ZTH6123KOLA 968999224 / ZTH6127KOB 968999225 / ZTH7227KOB For Serial No. 033600000 & Higher MANUAL 539109201 REV. 01 (09/15/04)
More informationHopper and Drive Components
Fisher Engineering 50 Gordon Drive, Rockland, Maine 04841-2139 www.fi sherplows.com 80152 September 1, 2015 Lit. No. 43774, Rev. 00 Hopper and Drive Components SPEED-CASTER 525 Low-Profile Tailgate Spreader
More informationWELDING POSITIONER PARTS BREAKDOWN DRAWING GP-200
WELDING POSITIONER PARTS BREAKDOWN 10 DRAWING GP-200 1 GP-200-001 FRAME 1 2 GK-160-012 5/16"-18UNC x 5/8" CARRIAGE BOLT 6 3 GK-136-055 5/16"Ø LOCK WASHER 6 4 GK-109-052 5/16"-18UNC HEX NUT 10 5 GP-200-002
More information" PLUG AERATOR. Model No. Safety Assembly Operation Maintenance Parts. CAUTION: Read Rules for Safe Operation and Instructions Carefully
owner s manual Model No. 45-0383 48" PLUG AERATOR CAUTION: Read Rules for Safe Operation and Instructions Carefully Safety Assembly Operation Maintenance Parts the fastest way to purchase parts www.speedepart.com
More informationField Install Scale. WI /14 Rev. 0 Page 1 of 19
Field Install Scale WI00703 11/14 Rev. 0 Page 1 of 19 850 1050 Page 2 of 19 Tools you will need for Field Install Scale For 850/1050 Axles 1 1/8 socket for lug nuts. For 850/1050 Dual Axles 1 3/8 socket
More informationREPAIR INSTRUCTIONS. Cat. No Cat. No MILWAUKEE ELECTRIC TOOL CORPORATION. SDS Max Demolition Hammer. SDS Max Rotary Hammer
Cat. No. 9-0 SDS Max Demolition Hammer Cat. No. -0 SDS Max Rotary Hammer MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON ROAD BROOKFIELD, WISCONSIN 00-0 8-9-0 d 000 8-9-0 d Special Tools Require Forcing
More informationOperator and Parts Manual
Operator and Parts Manual Conventional Auger 8" & 10" x 36', 41', & 51' Model 092010 FK335 Table of Contents - 8" & 10" x 36', 41', & 51' Conventional Auger Table of Contents Introduction...5 Safety...6
More information