ORDIC FIBERGLASS, INC.

Transcription

1 s, 3 Phase Sectionalizing 15kV 200Amp s Nordic cabinets are produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using woven roving glass reinforcement, which adds greatly to their strength. The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet Stainless steel continuous hinge connects the lid to the cabinet. One stainless steel self locking cam arm and prop arm hold the lid open. ND-315-MG-2A5A-X-X: One-piece design for the ND-315, ground sleeve is part of the cabinet. Hot-dipped galvanized MP-2A5A mounting plate (also available in stainless steel) accommodates up to three 2, 3 or 4 pt., 15kV 200A loadbreak junctions with U-straps. In-line parking allows for parking stand-offs or 2 pt. feedthroughs on either side of the mounting plate. ND-2315-MG-2A5A-X-X: Two-piece design for the ND It can also be used for pad-mount applications without the ground sleeve. Hot-dipped galvanized MP-2A5A mounting plate (also available in stainless steel) accommodates up to three 2, 3 or 4 pt., 15kV 200A loadbreak junctions with U-straps. In-line parking allows for parking stand-offs or 2 pt. feedthroughs on either side of the mounting plate. The cabinet s eyebolts allow the lineperson to simply hook-up the direct burial cabinet, position it over the cables, and place it in the excavated area. ND-315-MG-2A5A-X-X 15kV 200Amp Three Phase Sectionalizing s Burial ND-315-MG-2A5A-X-X In-Line Finish grade ND-2315-MG-2A5A-X-X In-Line below locking system. ND-2315-MG-2A5A-X-X Page 19

2 15/25kV 200Amp s One-piece design, ground sleeve is part of the cabinet. Nordic cabinets are produced of fire retardant resin and a combination of chopped glass spray-up and hand lay-up using woven roving glass reinforcement, which adds greatly to their strength. The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet One stainless steel self locking cam arm and prop arm hold the lid open. Stainless steel continuous hinge connects the lid to the cabinet. ND-250-MG-101-X-X: ND-250-MG-101-X-X is used for pad-mount installations. anchor brackets (4x) are shipped attached to the mounting plate for pad mounting. Concrete anchoring hardware is not included. ND-330-MG-101-X-X, ND-350-MG-101-X-X, ND-360-MG-101-X-X: Hot-dipped galvanized MP-101 mounting plate (also availabe instainless steel) accommodates up to three 2, 3, or 4 pt., 15/25kV 200A loadbreak junctions with U-straps, except Cooper 35kV. (ND-330-MG-101-X-X is designed for 15kV 200Amp LBJ s only) Does not accommodate 200A taps off of the 600A junctions. (Includes ND-250) Below parking on the MP-101 allows for parking stand-offs or 2 pt. feedthroughs on either side of the mounting plate. The cabinet s eyebolts allow the lineperson to simply hook-up the direct burial cabinet, position it over the cables, and place it in the excavated area. 15/25kV 200Amp s Burial ND-330-MG-101-X-X (15kV only) Below Finish grade ND-350-MG-101-X-X Below below locking ND-360-MG-101-X-X Below system. ND-250-MG-101-X-X Below Pad-Mount ND-250-MG-101-X-X ND-330-MG-101-X-X ND-350-MG-101-X-X ND-360-MG-101-X-X Page 20

3 15/25/35kV 600Amp s ND-430-MG-101-X-X, ND-450-MG-101-X-X One-piece design for the ND-430 and ND-450, ground sleeve is part of the cabinet. Nordic cabinets are produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using woven roving glass reinforcement, which adds greatly to their strength. The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet Two stainless steel self locking cam arms hold the lid open. Stainless steel continuous hinge connects the lid to the cabinet. Hot-dipped galvanized MP-101 mounting plate,(also available in stainless steel) accommodates up to three 2, 3 or 4 pt., 15/25/35kV 200A and 600A loadbreak junctions with U-straps, except for Cooper 35kV. Optional hot-dipped galvanized MP mounting plate, (also available in stainless steel) accommodates up to three 2, 3, or 4 pt., 35kV 600Amp deadbreak junctions with U-straps from Cooper. Accommodates 200A taps off of the 600A junctions. Below parking allows for stand-offs or feed throughs to be installed. ND-450 has an optional 18 or 36 high extension for extra cable bending radius. The cabinet s four eyebolts allow the lineperson to simply hook-up the cabinet, position it over the cables, and place it in the excavated area for a simple installation. ND-430-MG-101-X-X 15/25/35kV 600Amp s Burial ND-430-MG-101-X-X Below Finish grade ND-450-MG-101-X-X Below below locking system. ND-450-MG-101-X-X Page 21

4 15/25kV 200Amp Three Phase Roto-Cab Sectionalizing s ND-5524 Series One-piece design for the ND-5224 Series cabinets, ground sleeve is part of the cabinet. Nordic cabinets are produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using woven roving glass reinforcement, which adds greatly to their strength. The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet Hot-dipped galvanized MP-101 mounting plate accommodate up to three 2, 3 or 4 pt., 15/25kV 200/600A loadbreak junctions with U-straps. Does not accommodate 200A taps off of the 600A junctions. MP-101 below parking allows for stand-offs or feed throughs to be installed. MP-152, PA58, PB58 mounting plates accommodate up to three 2, 3 or 4 pt., 15/25kV 200A loadbreak junctions with U-straps. The sliding rail on the 152 and PA58 allows for stand-offs or feed throughs to be installed on the stainless steel above parking stands, or the below parking stands on the PB58. The cabinet s four eyebolts allow the lineperson to simply hook-up the cabinet, position it over the cables, and place it in the excavated area for a simple installation. ND MG-152-X-X ND MG-101-X-X ND MG-PA58-X-X ND MG-101-X-X ND MG-152-X-X & ND MG-PA58-X-X 15/25kV 200Amp s Burial ND MG-101-X-X Below ND MG-152-X-X Above ND MG-PA58-X-X Above ND MG-101-X-X Below ND MG-152-X-X Below ND MG-PA58-X-X Above ND MG-101-X-X Below ND MG-152-X-X Above ND MG-PA58-X-X Above Finish grade 6 below locking system. ND MG-101-X-X ND MG-152-X-X & ND MG-PA58-X-X Page 22

5 15/25kV 200 and 15/25/35kV 600Amp Three Phase Roto-Cab Sectionalizing s Two-piece design for the ND and ND Nordic cabinets are produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using woven roving glass reinforcement, which adds greatly to their strength. The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet provides double locking. Two stainless steel self locking cam arms hold the lid open. ND MG-101-X-X & ND MG-152-X-X: Hot-dipped galvanized MP-101 & MP-152 mounting plates accommodates up to three 2, 3, or 4 pt., 15/25kV 200A loadbreak junctions with U-straps. Does not accommodate 200A taps off the 600A junctions. MP-101 below parking allows for stand-offs or feed throughs to be installed. MP-152 above parking allows for stand-offs or feed throughs to be installed. MP-152 plate can be rotated horizontally for easy junction installation. ND : Hot-dipped galvanized MP-168 mounting plate accommodates up to three 2, 3, or 4 pt., 15/25/35kV 200A loadbreak junctions. It also accommodates 200A taps off of the 600A junctions. MP-168 above parking allows for stand-offs or feed throughs to be installed. MP-168 mounting plate can be rotated horizontally for easy junction installation. The cabinet s four eyebolts allow the lineperson to simply hook-up the cabinet, position it over the cables, and place it in the excavated area. Two-Piece 15/25kV 200Amp s ND MG-101-X-X Below ND MG-152-X-X Above Two-Piece 15/25/35kV 600Amp Three Phase Sectionalizing s ND MG-168-X-X Above Burial Finish grade 6 below locking system. ND MG-101-X-X ND MG-152-X-X ND MG-168-X-X Page 23

6 15/25/35kV 600Amp Three Phase Roto-Cab Sectionalizing s One-piece design, ground sleeve is part of the cabinet. Nordic cabinets are produced of fire-retardant resin and a combination of chopped glass spray-up and hand layup using woven roving glass reinforcement, which adds greatly to their strength. The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet P-107 stainless steel locking system with a silicon bronze penta-head bolt Meets ANSI C Pad-Mounted Enclosure Integrity Standard. ND-6830 Series: Aluminum PA71 or PB71 mounting plate accommodates up to three 2, 3 or 4 pt., 15/25/35 kv 200A or 600A junctions with U-straps (accommodates 200A taps), including Cooper 35 kv 200A/600A junctions. Accommodates 200A taps off of the 600A junctions. The sliding rail on the PA71 or PB71 allows for stand-offs or feed throughs to be installed on the stainless steel parking stands either above (PA71) or below (PB71). ND has an optional 18 or 36 high extension for extra cable bending radius. The cabinet s four eyebolts allow the lineperson to simply hook-up the cabinet, position it over the cables, and place it in the excavated area. ND MG-PA71-X-X 15/25/35kV 600Amp s Burial ND MG-PA71-X-X Above Finish grade ND MG-PA71-X-X Above below locking system. ND MG-PA71-X-X Page 24

7 ND-325 (Standard) & (Multi-Point Junction ) Rust free fiberglass construction and stainless steel hardware. One-piece design, ground sleeve is part of the cabinet. Nordic cabinets are produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using woven roving glass reinforcement, which adds greatly to their strength. The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet provides double locking. Two stainless steel self locking cam arms hold the lid open. Stainless steel continuous hinge connects the lid to the cabinet. Standard: ND-325-MG-2C5A-X-X: Hot-dipped galvanized MP-2C5A mounting plate in the ND-325, (also availabe in stainless steel) accommodates up to three 2, 3, or 4 pt., 15/25kV 200A loadbreak junctions with U-straps. Does not accommodate 200A taps off of the 600A junctions. In-line parking on the MP-2C5A allows for parking stand-offs or 2 pt. feedthroughs on either side of the mounting plate. Multi-Point: ND-325-MG-S102CX-X-X, ND-325-MG-X-X-X Accommodates a variety of 5 and 6 way 15/25/35kV multiple point junctions with 4 interface spacing from a variety of manufacturers including Elastimold, Hubbell, G&W, and Cooper linear junctions. (Check out our website for junction accommodations) Junctions without parking stands can either be mounted to a mounting plate or mounted to the cabinet s fiberglass mounting board with their own mounting bracket. Multi-Point junctions allow for different configurations of 200A and 600A interfaces for either load or dead break elbows. Does not accommodate 200A taps off of the 600A junctions. The cabinet s four eyebolts allow the lineperson to simply hook-up the cabinet, position it over the cables, and place it in the excavated area. ND-325-MG-2C5A-X-X ND-325-MG-S102CX-6252B-W3B ND-325 Mounting Plate Stands Mounting Board ND-325-MG-2C5A-X-X 2C5A In-Line ND-325-MG-S102CX-X-X S102CX Below ND-325-MG-X-X-X Based on Junction Below ND-325-MG-X W3B Page 25

8 ND (Standard) & (Multi-Point Junction ) Rust free fiberglass construction and stainless steel hardware. Two-piece design. Nordic cabinets are produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using woven roving glass reinforcement, which adds greatly to their strength. The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet Two stainless steel self locking cam arms hold the lid open. Multi-Point: ND MG-268-X-X: ND : Accommodates a variety of 15/25/35kV multiple point junctions with 4 interface spacing from a variety of manufacturers including Elastimold, Hubbell, and G&W. (Check out our website for junction accommodations) Hot-dipped galvanized MP-268 mounting plate accommodates up to three 2, 3, or 4 pt., 15/25/35kV 200A loadbreak junctions. It also accommodates 200A taps off of the 600A junctions. MP-268 above parking allows for stand-offs or feed throughs to be installed. MP-268 mounting plate can be rotated horizontally for easy junction installation. The cabinet s four eyebolts allow the lineperson to simply hook-up the cabinet, position it over the cables, and place it in the excavated area. ND MG-268-X-W3B ND MG CB2-W3B ND MG C2R-W3B Two-Piece 15/25kV 200Amp Three Phase Multi-Point Sectionalizing ND MG-268-X-X Above Burial Finish grade 6 below locking system. ND MG C3-W3B Page 26