PIPE/CONDUIT SUPPORTS
|
|
- Kelly Hill
- 6 years ago
- Views:
Transcription
1 PIPE/CONDUIT SUPPORTS Pipe/Conduit Clamps Unicushion Pipe & Tubing (Cush-A-Clamp ) Clamps Pipe Hangers Pipe Rollers Pipe Brackets Reference Tables MATERIAL Unistrut pipe clamps, unless noted, are punch-press made from hot-rolled, pickled and oiled steel plates, strip or coil, and conform to ASTM specifications A1008, A575, A576, A635, or A36. The fitting steel also meets the physical requirements of ASTM A1011 SS GR 33. The pickling of the steel produces a smooth surface free from scale. Many items are also available in stainless steel. Consult factory for ordering information. FINISHES Pipe supports are available in: Electro-galvanized (EG), conforming to ASTM B633 Type III SC1 Hot-dipped galvanized (HG), conforming to ASTM A123 or A153 (hardware) Perma-Green III (GR), and plain (PL). APPLICATION Unistrut pipe clamps, pipe hangers, brackets and rollers are designed for the support of electrical and mechanical services. Supports to meet nearly every requirement can be attained using Unistrut Metal Framing components. DIMENSIONS Imperial dimensions are illustrated in inches. Metric dimensions are shown in parenthesis or as noted. Unless noted, all metric dimensions are in millimeters and rounded to one decimal place. DESIGN BOLT TORQUE Note: When tightening 1 4" screws used with a two piece pipe clamp, a torque of 5 foot pounds (60 inch-pounds) should be used. DESIGN LOAD Design load data, where shown, is based on the ultimate strength of the connection with a safety factor of 5.0, unless otherwise noted. Pipe Clamps In Special Materials (P1109, P1211, P1425, P2024 Series) Steel Strap, Everdur Hardware E P1109 E Copper Coated Steel Strap & Hardware CC P1109 CC Aluminum Material: Malleable Iron. AL P1109 AL Stainless Steel 304 or 316 SS or ST P1109 SS 101
2 Pipe & Conduit Pictorial Index Pipe & Conduit Clamps P Pg 102 P Pg 103 P Pg 103 P Pg 104 P Pg 103 P Pg 103 P Pg 104 P Pg 105 P Pg 105 MU025 - Pg 105 P Pg T008 - Pg M007 - Pg 108 UB 1 2PA - Pg 109 CG-10 - Pg 110 PUX Pg 110 Pipe Rollers J Pg 111 P Pg 111 P Pg 112 P Pg 112 P Pg 113 Pipe Brackets P Pg 113 P Pg 113 P Pg " (31.8) Design Load 102 Pipe/Conduit Supports
3 Pipe & Conduit Clamps 1 1 4" (31.8) Design Load 1 3 8" (34.9) 1 1 4" (31.8) 1 1 4" (31.8) Design Load 1 4" X 3 4" Round Head Machine Screw and Channel Nut Not Included Pipe/Conduit Supports 103
4 Pipe & Conduit Clamps P P ga. P P ga. P P ga. P P ga. P P ga " (31.8) Design Load (6.4) (3.6) (9.5) (3.6) (12.7) (4.1) (15.9) (4.5) (19.1) (5.0) (22.2) (5.4) (25.4) (6.4) (28.6) (6.8) (31.8) (7.3) (34.9) (7.7) (38.1) (8.2) (41.3) (8.6) (44.5) (13.2) (47.6) (12.7) (50.8) (14.1) (54.0) (14.5) (57.2) (15) (60.3) (15.4) (63.5) (15.9) (66.7) (16.8) (69.9) (17.2) (73.0) (18.1) (76.2) (18.6) (79.4) (19.5) (82.6) (20.4) (85.7) (20.9) (88.9) (21.3) (92.1) (25.4) (95.3) (26.3) (98.4) (27.2) (101.6) (28.1) (104.8) (28.1) (108.0) (29.0) (111.1) (29.9) (114.3) (30.4) (117.5) (31.8) (120.7) (32.7) (1.78) (2.67) (3.56) (4.45) (123.8) (33.1) (127.0) (33.6) (130.2) (34.5) (133.4) (34.9) (136.5) (35.4) (140.0) (35.8) (142.9) (39.9) (146.1) (40.8) (149.2) (41.7) (152.4) (42.6) (155.6) (43.5) (158.8) (44.5) (161.9) (44.9) (165.1) (45.4) (168.3) (46.3) (171.5) (47.2) (174.6) (48.1) (177.8) (49.0) (181.0) (49.9) (184.2) (50.8) (187.3) (51.7) (190.5) (52.6) (193.7) (53.1) (196.9) (54.0) (200.0) (54.9) (203.2) (55.8) (206.4) (56.7) (209.6) (57.2) (212.7) (58.1) (215.9) (58.5) (219.1) (59.0) (4.45) A ± 1 8" C Design Load Supporting Rib on P Hole Size B 104 Pipe/Conduit Supports
5 Pipe & Conduit Clamps E C D A B UNI-CLIP SUPPORTS FOR THINWALL CONDUIT (E.M.T.) H UNI-CLIP SUPPORTS FOR RIGID STEEL CONDUIT Pipe/Conduit Supports 105
6 UNICUSHION EMT CONDUIT (6.4) (22.2) (9.5) (27.0) (12.7) (38.1) (15.9) (54.0) (19.1) (57.2) (22.2) (76.2) (25.4) (82.6) (28.6) (92.1) (31.8) (101.6) (34.9) (114.3) (38.1)) (123.8) (41.3) (133.4) (44.5) (139.7) (47.6) (152.4) (50.8) (165.1) (54.0) (171.5) (57.2) (184.2) (60.3) (190.5) (63.5) (203.2) (66.7) (209.6) (69.9) (222.3) (73.0) (235.0) (76.2) (241.3) STANDARD PIPE OR RIGID CONDUIT UNICUSHION FEATURES COPPER TUBING TYPE K OR L Shock absorption Protection from corrosion and abrasion Allowance for expansion and contraction in pipe diameter Sound and vibration isolation Stability in use from - 50 F (-47 C) to F (+177 C) Flexible elastomer material Will not support combustion (79.4) (254.0) (82.6) (266.7) (85.7) (273.1) (88.9) (279.4) (92.1) (285.8) (95.3) (292.1) (98.4) (298.5) (101.6) (304.8) (104.8) (317.5) (108.0) (330.2) (111.1) (342.9) (114.3) (355.6) (117.5) (362.0) (120.7) (374.7) (123.8) (381.0) (127.0) (393.7) (130.2) (406.4) (133.4) (412.8) (136.5) (419.1) (139.7) (431.8) (142.9) (444.5) (146.1) (450.9) (149.2) (463.6) (152.4) (469.9) (155.6) (482.6) (158.8) (489.0) (161.9) (501.7) (165.1) (508.0) (168.3) (520.7) (171.5) (533.4) (174.6) (539.8) (177.8) (552.5) (181.0) (558.8) (184.2) (571.5) (187.3) (577.9) (190.5) (590.6) (193.7) (596.9) (196.9) (609.6) (200.0) (622.3) (203.2) (628.7) (206.4) (635.0) (209.6) (647.7) (212.7) (660.4) (215.9) (666.8) 106 Pipe/Conduit Supports
7 Pipe & Tubing Clamps D Controlled Squeeze Shoulder Bolt on sizes up to 1 3 8" OD Living B Hinge Materials: Clamp: Electro-galvanized or stainless steel. Cushion: Thermoplastic elastomer. (UV Resistant) Includes cushion, clamp and hardware. Temperature Rating: -50 F to +275 F (-45 C to +135 C) Insert Width: 1.56" (39.6) Part Numbers are "coded" to designate cushion size and clamp size. Examples: 004T Cushion Size 4 16" (6.4) T - With Controlled Squeeze Shoulder Bolt Available on sizes up to 1 3 8" Clamp Size 8 16" (12.7) 009N Cushion Size 9 16" (14.3) N - With Standard Bolt Clamp Size 12 16" (19.1) Pipe Series Assembly A C Tube Series Assembly Pipe/Conduit Supports 107
8 Pipe & Tubing Clamps A F G E D B C H J E 108 Pipe/Conduit Supports
9 Pipe & Tubing Clamps D B A H E 30 (0.2π) C Pipe/Conduit Supports 109
10 Pipe & Tubing Clamps B A C D " (36.5) V-Pad Captured Nylon Lock-Nut "V" Pad 1 5 8" Series Channel Size Range "V" Pad Hex Bolt The only airtight, crush-resistant insulation clamp on the market. Maintains thermal barrier protection Prevents condensation Properly supports pipe and tube Absorbs vibration Nominal 3 4" Wall 1. Insulation slides over pipes 2. Pipe hanger inserts are put in place and glued to insuation. Nominal 1" Wall 3. Joints are wrapped and sealed with ProTape. 110 Pipe/Conduit Supports
11 Pipe Hangers "T" Bolt and Nut Included C B D Plastic Coated Rod Size A Listed Hanger Rod Suspended Hex Bolt Size as Listed Plastic Coated ("N" Suffix) Rod Size A Bolt Size F Hole Diameter E Sold in pairs. A 2 1 2" (63.5) Cast iron rollers. Design Load 500 Lbs (2.22kN) Pipe/Conduit Supports 111
12 Pipe Rollers 3" (76.2) A A 2 1 2" (63.5) 2" (50.8) Saddle by others " 3 3 4" (88.9) TO (95.3) Sold separately. Design Load 1500 Lbs (6.67 kn) Design Load 750 Lbs (3.34 kn) 112 Pipe/Conduit Supports
13 Pipe Brackets 2" (50.8) Design Load 2000 Lbs (8.90 kn) 3" (76.2) A 3 1 4" (82.6) 3 1 2" (88.9) 4" (101.6) 1 4" (6.4) 4 3 8" (111.1) 3 8" (9.5) 4" (101.6) 3" (76.2) Hole Size 7 16" (11.1) 1" (25.4) Clamp Requires bolt and channel nut. Sold seperately Pipe/Conduit Supports 113
14 Pipe & Conduit Reference Data 114 Pipe/Conduit Supports
15 Pipe & Conduit Reference Data Pipe/Conduit Supports 115
16 Pipe & Conduit Reference Data 116 Pipe/Conduit Supports
17 Pipe & Conduit Reference Data Pipe/Conduit Supports 117
18 Pipe & Conduit Reference Data 118 Pipe/Conduit Supports
19 Pipe & Conduit Reference Data * Maximum weight equals weight of rigid conduit plus weight of heaviest conductor combination (from the National Electrical Code Handbook.) The above spacing based on a combined bending and shear stress of 1500 PSI when pipe is filled with water and the pitch of the line is such that a sag of 0.1 in. between supports is permissible Supports. Rigid metal conduit shall be installed as a complete system as provided in Article 344 and shall be securely fastened in place. Conduit shall be firmly fastened within 3 feet (914.4 mm) of each outlet box, junction box, cabinet, or fitting. Conduit shall be supported at least every 10 feet (3.05 m). Exception: If made up with threaded couplings, it shall be permissible to support straight runs of rigid metal conduit in accordance with Table (B)(2), provided such supports prevent transmission of stresses to termination where conduit is deflected between supports. Pipe/Conduit Supports 119
20 Pipe & Conduit Reference Data 120 Pipe/Conduit Supports
Clamp Pair. Bore Diameter (mm) Clamp Material PP = Polypropylene PA = Polyamide PE = Polyethylene AL = Aluminum
DIN 0 CLAMPS Clamp Pairs HRL = Standard Duty (Ribbed Profile) HRGL = Standard Duty (Smooth Profile) HRS = Heavy Duty (Ribbed Profile) HRGS = Heavy Duty (Smooth Profile) Clamp Pair ore Diameter (mm) Clamp
More informationTechline Flat Cross Splice. Techline Yoke Clamps* Techline Gang Clamps* TECHLINE. *Yoke Clamps Are Available To Fit Any Width.
Techline Flat Cross Splice SIZE HD GALVANIZED ALUMINUM 304 SS 2Ó TLXS-2 HDG TLXS-2 AL TLXS-2 SS 3Ó TLXS-3 HDG TLXS-3 AL TLXS-3-SS 4Ó TLXS-4 HDG TLXS-4 AL TLXS-4 SS 6Ó TLXS-6-HDG TLXS-6 AL TLXS-6 SS TECHLINE
More informationGround Clamps Cable Tray
commercial and industrial fittings: ing Fittings and Solderless Connectors Clamps Cable Tray Terminates ground wire to cable tray. For aluminum or copper conductors. 1 4 hex wrench tightens both tray and
More informationCopper Tubing Hangers Clevis Hangers. Copper Tubing Hangers
Copper Tubing Hangers Clevis Hangers Copper Tubing Hangers Fig. CT-69 Adjustable Swivel Rug Fig. CT-138R Fig. CT-65 Fig. CT-109 Extension Split Light Weight Adjustable Clevis Fig. CT-99 & CT-99C Split
More informationIndex Pipe Hangers and Straps
Index Pipe Hangers and Straps Fig. 1 Standard Clevis Hanger MSS-SP-69, Type 1 WW-H-171E, Type 1 Page 14 Fig. 1CI Clevis Hanger for A.W.W.A. Page 16 Fig. 81 Clevis Hanger WW-H-171E, Type 12 Page 70 Fig.
More informationH HD Adult Wheelchair Swing Frame & Hangers(perm) IMPORTANT
Page 1 IMPORTANT PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING ASSEMBLY. All equipment must be installed in accordance with these instructions. Check your shipment against Bill of Lading and Parts list.
More informationBeam and Purlin Clamps Beam Clamps
Metal Framing & Cable Tray Steel City Hangers, Clamps & Fasteners Beam and Purlin Clamps Beam Clamps Fits beam flanges to 2" Supports 4" and 8" threaded rod, S-hooks, electrical boxes, conduit and bridle
More information5/16" Flange nut. Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc plated bolt w/ washers and nut. Anchor 3" sq. 7 Ga.
2 1/2" x 2 1/2" x 10 Ga. 6" 5" 4" Variable Slipbase (8" Sq. SYS.) 5/16 Corner Bolt W/ nut 5/16" Flange nut Stub Insert (8" Sq. SYS.) Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc
More informationThru Wall Floor Seals For New Installation
The O-Z/Gedney Thruwall and Floor Seals provide a positive means of sealing pipe, conduit or tube where they pass through a concrete foundation of a structure below grade or below ground water level or
More informationUP43 LEARN-A-L0T (NATURAL) Parts List DESCRIPTION 90 ANGLE BRACKET DOOR WINDOW MUSIC CATERPILLAR CIRCLE FRAME CIRCLE MIRROR YELLOW STAINED GLASS RED STAINED GLASS SQUARE TRIANGLE SPIRAL WHEEL SQUARE MIRROR
More informationUP4 LEARN-A-LOT (PLAYFUL) Parts List DESCRIPTION 90 ANGLE BRACKET DOOR WINDOW MUSIC CATERPILLAR CIRCLE FRAME CIRCLE MIRROR YELLOW STAINED GLASS RED STAINED GLASS SQUARE TRIANGLE SPIRAL WHEEL SQUARE MIRROR
More informationP2784 3" (76.2) (31.8) 25 to 45 PFL2-37
P289 (2.0) (.) 2 (.2) 2 (2.4) 2 (.2) hreaded esign (Safety Factor of 4) (angles 2 ) - 0 Lbs (2.4 kn) ) - 0 Lbs (.4 kn) Safety Factor 4 orque: Ft-Lbs (8 N m) PFL2- to (.2 to 9.) 2 2 2 2 to 4 t/00 : Lbs
More informationGeneral Information...SA1-SA4
SECTION S INDEX Product Description Page Number General Information................................................................SA1-SA4 Type FSK Thruwall & Floor Seal For Conduit, Pipe or Tubing............................
More informationTransmission Line Support Systems
Antenna Support Bracket for transmission line The Antenna Support Bracket angle mounts directly to a 4-1/2" (114 mm) OD antenna pipe mount or tower leg. This is ideal for supporting transmission line runs
More informationINSIDE PANEL NOT SHOWN TO DETAIL ANCHORING SYSTEM
SIX INCH ALPHA MODULE INSTALLATION KEWAUNEE SCIENTIFIC CORPORATION SIX INCH ALPHA MODULE ANCHORING SYSTEM After Alpha module has been set in desired location. Adjust the four adjustment bolts until the
More informationPRODUCT CATALOG Meadowview Rd Junction City, OR fax
Made in the USA, since 1972 PRODUCT CATALOG Nichols Manufacturing 292 Meadowview Rd Junction City, OR 97448 541-485-60 sales@nicholsmanufacturing.com www.nicholsmanufacturing.com 122616 Nichols Manufacturing
More informationSECTION METAL FABRICATIONS
SECTION 05100 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes specifications for metal fabrications, including minimum requirements for fabricator, and galvanizing. 1.02 REFERENCE STANDARDS A. ASTM
More informationSuperstrut. Metal Framing. Beam Clamps. Design Loads. Finishes and Special Materials
Loads Where design loads are indicated, they provide for a safety factor of 3 in conformance with the merican Standard Code for Pressure Piping. For more information, see page 57 for Engineering Data and
More informationTesting. Material testing will be according to applicable AASHTO, ASTM or Department methods as specified.
907.01 Section 907. FENCING MATERIALS 907.01 General Requirements. Materials for use in fencing property, right-of-way and other installations must comply with this section. 907.02 Testing. Material testing
More informationINTERMEDIATE METAL CONDUIT
PRODUCT GUIDE 08 CONDUIT PIPES CONDUIT FITTINGS FITTINGS FOR FLEXIBLE CONDUITS METALLIC ELECTRICAL BOXES AND COVERS CONDUIT BODIES WEATHERPROOF BOXES AND COVERS CHANNELS & SUPPORTS METAL ENCLOSURES CHANNELS
More informationSTEEL C-CLAMP WITH LOCKNUT
FIG. 250 STEEL C-CLAMP WITH LOCKNUT Function: Designed for attaching hanger rod to the bottom flange of a beam. The hanger rod should make contact with the beam flange to ensure full engagement. Material:
More informationPACKING LIST MACO V-5000
PACKING LIST MACO V-5000 PART QTY O.D. SIZE LENGTH DESCRIPTION CHECKLIST T47P 4 5/8.050 36 Aluminum Tubing _ T43P 1 7/8.050 48 Aluminum Tubing _ T18P 1 3/4.050 48 Aluminum Tubing _ T15P 1 5/8.050 48 Aluminum
More informationUP139 CRUISE-A-LONG (STANDARD) NATURAL COATED DECK COATED RAMP DESCRIPTION SQUIRREL PANEL BACK WALL CLEAR BUBBLE CRUISE RAIL SQUARE SPIRAL WHEEL 90 AN
UP39 CRUISE-A-LONG (STANDARD) NATURAL COATED DECK COATED RAMP DESCRIPTION SQUIRREL PANEL BACK WALL CLEAR BUBBLE CRUISE RAIL SQUARE SPIRAL WHEEL 90 ANGLE BRACKET TUBE BRACKET TUBE WARNING LABEL PLATE HARDWARE
More informationDOCUMENT ADDENDUM NO. 4. Issued to all Bidders: Date: October 14, Contract Name: Electrical Installation. Contract Number: C8410
DOCUMENT 009104 - ADDENDUM NO. 4 Issued to all Bidders: Date: October 14, 2015 Contract Name: Electrical Installation Contract Number: C8410 This addendum forms a part of the Bid described above. The original
More informationSection Member. H (in.) WT. lb./ft. Pull Out Strength Slip Resistance Torque Size / Thread All Series
Design Data Channel TABLE 1 Elements of Sections Properties for Design Single Channels Nominal Thickness (inches) ga = 0.105 ga = 0.075 16 ga = 0.060 Double Channels LEGEND I Moment of inertia S Section
More informationStructural Bolting. Notice the Grade 5 has a much smaller head configuration and a shorter shank then the grade A325 structural bolt.
Structural Bolting ASTM F3125/F3125M is a structural bolt specification covering inch and metric bolt grades. This specification contains 4 inch series bolting grades: A325, F1852, A490, and F2280. These
More informationCaptive Quarter-turn Fasteners Continuous Receptacle Strip MIL-F-25173A * APPROVED
Solutions Inc. PA-3500 Line Captive Quarter-turn Fasteners Continuous Receptacle Strip MIL-F-25173A * APPROVED The DFCI PA-3500 Line of fasteners combine the operating convenience, predictable clamping
More informationInstallation Instructions for Solar Snow Pad (SSP-T-3)
Installation Instructions for Solar Snow Pad (SSP-T-3) Warning- Do not use this product on solar arrays where the calculated array snow loads exceed 50 pounds per square foot (psf). Most solar panels are
More informationPART MATERIALS. Section Fencing Materials. Description
PART 03000 - MATERIALS Section 03010 - Fencing Materials Description 03010.00 Scope - This section consists of the test requirements, specifications and tolerances for barbed wire, woven wire and chain
More informationFactory Assistance: Phone: Fax: Page 1
CABLE RUNWAY ACCESSORIES Radius Drop / Stringer Drop Provides 3 bend radius Radius drop fits 6, 12 and 18 runway made from 1-1/2 x 3/8 tubing Steel construction Includes (3) cable spools, (1) bolt, (1)
More informationCat. No. A1200 A1200-S A1200-KO. Finishes & Materials. E142-1/4x100EG 1/4 x 1 A100-5/16EGC A100-3/8EGC. Standard Finish: Electrogalvanized
Superstrut Support Systems 1-5/8 in. x 1-5/8 in. Channel and Hardware Superstrut 1-5/8 in. x 1-5/8 in. - 12 Gauge Channel Type A Solid Base Punched Description Solid base -P Punched -HS Half slots Half
More informationSuperstrut. Metal Framing. Beam Clamps. Design Loads. Finishes and Special Materials
Loads Where design loads are indicated, they provide for a safety factor of 3 in conformance with the merican Standard Code for Pressure Piping. For more information, see page 57 for Engineering Data and
More informationRIDGE MAST MOUNT (RMM)
May 5, 009 Revision E ASSEMBLY MANUAL (RMM) General Dynamics Satcom Technologies 1500 PRODELIN DRIVE NEWTON NC 8658 88-464-4141 www.gdsatcom.com 1.0 INTRODUCTION: 1.1 Features: The Ridge Mast Mount (RMM)
More informationMax. Rec. Load. Wt. Per Inch lbs. kn lbs. kn lbs. kg. Wt. Per Inch lbs. kn lbs. kn lbs. kg 750 F (399 C)
FIG. 10 FIG. 15 & 15L Function: Designed for use in pipe hanger assemblies. (Type 304 or 316 Stainless Steel upon request) Ordering: Specify figure number, rod size, length (), material, and finish. 650
More informationWESTERN WIRE PRODUCTS
WESTERN WIRE PRODUCTS Celebra ng 100 years of Quality and Service 1914 2014 Thanks to our dedicated employees and customers we are celebra ng 100 years of being in business and we look forward to servicing
More informationMAST ARMS & POLES. Ornamental Pole Top & Bases
Ornamental Pole Top & Bases Pelco s decorative pole top and bases make the traffic signal aesthetically pleasing to the eye. In addition to the standar 4-piece, Pelco also manufactures the bases with an
More informationFURNITURE LABORATORY METAL FRAMING SYSTEM. For additional information and help in planning contact Mott Manufacturing.
LABORATORY Continuous Slot Metal Framing System For additional information and help in planning contact Mott Manufacturing. G22 Connection Instructions Installs quickly Completely adjustable Re-usable
More informationWAL-MART SUPERCENTER # ; Milwaukie, OR: SPECIFICATIONS. Revisions to Specification Fence
MILWAUKIE OR #3144-00 ADDENDUM #5 NARRATIVE: 11-08-12 WAL-MART SUPERCENTER #3144-00; Milwaukie, OR: SPECIFICATIONS SPECIFICATIONS Revisions to Specification 02822 Fence Spec division 02822 has been revised
More informationPunch Type Clamps. 116 Clamp guards provide a smooth ID when applied to Punch-Lok center punch hose clamps. PUNCH-LOK SPECIAL ORDER NON-STOCK CLAMPS
Hose Scribe Punch Type Clamps Hose Scribe 114 HOSESCRIBE Hose Identification System The First Self-Contained,Computerized Hose Identification Tag engraving System Three Easy Steps 1. Insert one of three
More informationInstallation Instructions: Bumper (Part # SB76850) XJ Jeep Cherokee XRC Rear Bumper
NOTE: Carefully read entire instructions thoroughly before attempting to install this part. Parts Included Qty 93-7789 XJ XRC 1 93-7807 Bumper Mount Bracket: Drvr 1 93-7811 Bumper Mount Bracket: Pass 1
More informationUP133 CRAWL & TODDLE (STANDARD) NATURAL COATED DECK COATED RAMP FRONT WALL BACK WALL DESCRIPTION COATED STEPS 90 ANGLE BRACKET LEFT WALL RIGHT WALL CL
UP33 CRAWL & TODDLE (STANDARD) NATURAL COATED DECK COATED RAMP FRONT WALL BACK WALL DESCRIPTION COATED STEPS 90 ANGLE BRACKET LEFT WALL RIGHT WALL CLEAR BUBBLE CRUISE RAIL SQUARE SPIRAL WHEEL TRIANGLE
More informationFord Water Meter Couplings & Accessories
Section H 2/2001 Ford Water Meter Couplings & Accessories The Ford Meter Box Co., Inc. 775 Manchester Avenue, P.O. Box 443, Wabash, Indiana, USA 46992-0443 Telephone: 260/563-3171 FAX: 1-800-826-3487 Overseas
More informationAPPENDIX FENCE GENERAL NOTES
APPENDIX FENCE GENERAL NOTES 1. Fabric: 9 gage, 2" mesh, knuckle top and bottom, placed on the outside of posts, single fabric width for the entire height. 2. All fencing to be standard galvanized finish.
More informationPOLE LINE HARDWARE POLE LINE HARDWARE. HI-LINE UTILITY SUPPLY CO. Phone: Fax:
146 MACHINE BOLTS w/ square nut Rolled threads; s six inches or longer have con-type points. Hot dip galvanized. 860412 3/8" 4.5" 3" 250 8706 6" 3" 100 8707 7" 3" 100 8708 1/2" 8" 4" 100 8710 10" 4" 50
More informationCOMMERCIAL ITEM DESCRIPTION RODS, GROUND (WITH ATTACHMENTS)
INCH-POUND 30 May 2002 SUPERSEDING A-A-55804 11 March 1996 COMMERCIAL ITEM DESCRIPTION RODS, GROUND (WITH ATTACHMENTS) The General Services Administration has authorized the use of this commercial item
More informationSECTION CABLE TRAYS FOR COMMUNICATIONS SYSTEMS
SECTION 270536 - CABLE TRAYS FOR COMMUNICATIONS SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationAssembly Instructions: Bencher Skylark
Assembly Instructions: Bencher Skylark Tools Required: Pop Rivet Tool Tape Measure Hex Wrenches Screwdriver Several Disposable Rags Two Saw Horses Several boxes or bowls to hold fasteners and small parts
More informationSECTION CHAIN LINK FENCING AND GATES
PART 1 GENERAL 1.01 SCOPE OF WORK A. The Contractor shall furnish and install all materials, labor, equipment and incidentals required to provide chain link fencing and gates as Shown on the Contract Drawings
More informationSuperstrut Stainless Steel Channels and Accessories
In this section... Superstrut Stainless Steel Channels and Accessories Superstrut Stainless Steel Channels and Accessories Channels...46 Channel Fittings and Hardware...47 49 Clamps and Hangers...50 52
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationMETRIC LIGHTNING PROTECTION PRODUCTS
Section 11 Metric Description... Page # 11.1 Taper Pointed Air Rods, Air Terminals & Attachments...270 11.2 Saddles & Attachments...271-272 11.3 s...273-275 11.4 Attachments...276-279 11.5 Clamps...280
More informationWaterpipe Ground Clamps. 1/2 in., 3/4 in., 1 or rebar /4 in., 1-1/2 in. or 2 in. 4 #6, #4, #2 AWG
Waterpipe Ground Ground Wire Size Water Pipe Size 2-T 1/2 in., 3/4 in., 1 or rebar 4-10 3-T 1-1/4 in., 1-1/2 in. or 2 in. 4 #6, #4, #2 WG 2-1/2 in., 3 in. or 3-1/2 in. 5-T 4 in., 4-1/2 in. or 5 in. 6 6
More informationNORMATIVE REFERENCES
American National Standards Institute NORMATIVE REFERENCES ANSI C135.30 1988 (expired 1993) Zinc-Coated Ferrous Ground Rod Electrodes for Overhead or Underground Lines American Society for Testing and
More informationHilti, Inc South 122 nd East Avenue Tulsa, OK
Attached are page(s) from the 2012 Hilti North American MI/MQ Technical Guide Volume 3. For complete details on this product, including data development, general suitability, installation, and corrosion
More informationPow-R-Feed Systems Service Manual
Pow-R-Feed Systems Service Manual Important Safety Instructions Please read this manual carefully and follow its instructions. Improper use or failure to follow these instructions could result in serious
More informationHilti, Inc South 122 nd East Avenue Tulsa, OK
Attached are page(s) from the 2013 Hilti North American Product Technical Guide Volume 1 Direct Fastening. For complete details on this product, including data development, product specifications, general
More informationSteel Casework Metal Framing System
MISCELLANEOUS ITEMS Continuous Slot Metal Framing System Installs quickly Completely adjustable Re-usable Eliminates all welding, drilling and use of special tools G23 METAL FRAMING SYSTEM 1. Place the
More informationD. Thermally Sprayed Metallic Coating (Flame Spray): STD SPEC
STANDARD SPECIFICATION SECTION 05121 MISCELLANEOUS METALWORK PART 1 - GENERAL 1.01 DESCRIPTION This section includes materials, fabrication, and installation of structural steel, connecting bolts, pipes,
More informationMEFA mounting accessories
MEFA mounting accessories Mounting accessories Base plates Page 5/2 Double holder Page 5/4 Height-adjustable suspensions Page 5/5 Pendular bolt joints Page 5/6 Trapeze hanger Page 5/7 Threaded hooks, distance
More informationI-W07/W77. Couplings DETAIL A WARNING. Photo Showing Pipe with Weld Seam Ground 6 inches/152 mm Back from Pipe End and an AGS Groove
WARNING Read and understand all instructions before attempting to install any Victaulic piping products. These products must be used only on pipe that is prepared to Victaulic Advanced Groove System (AGS)
More informationPunching 3/16" diameter round hole in up to 3/16" thick (flat strip metal).
Wrought Iron Handicrafts, Inc. 3950 10 th Ave NW Rochester MN 55901-1336 507-289-0836 phone 800-456-7738 phone info@metalcraftusa.com email The ultimate dream machine for fabricators and ornamental metal
More informationSECTION EXPANSION FITTINGS AND LOOPS FOR HVAC PIPING
SECTION 230516 - EXPANSION FITTINGS AND LOOPS FOR HVAC PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and
More informationNON-PENETRATING ROOFTOP HANGERS AND SUPPORTS
SECTION 15062 NON-PENETRATING ROOFTOP HANGERS AND SUPPORTS For best results, display hidden notes to specifier. PART 1 GENERAL 1.1 SECTION INCLUDES A. Pipe supports. B. Conduit supports. C. Duct supports,
More informationTIRE RACK INSTALLATION INSTRUCTIONS Dodge Sprinter
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 TIRE RACK INSTALLATION INSTRUCTIONS 07-11 Dodge Sprinter Please read before beginning Stainless steel hardware may bind together
More informationNORMATIVE REFERENCES
American National Standards Institute NORMATIVE REFERENCES ANSI C135.30 1988 (expired 1993) Zinc-Coated Ferrous Ground Rod Electrodes for Overhead or Underground Lines American Society for Testing and
More informationSECTION 7. SAFETYING
9/8/98 AC 43.13-1B SECTION 7. SAFETYING 7-122. GENERAL. The word safetying is a term universally used in the aircraft industry. Briefly, safetying is defined as: Securing by various means any nut, bolt,
More informationSECTION CONCRETE ANCHORING. Display hidden notes to specifier. (Don't know how? Click Here)
PART 1 GENERAL 1.1 SECTION INCLUDES SECTION 03 15 00 CONCRETE ANCHORING Display hidden notes to specifier. (Don't know how? Click Here) A. General purpose mechanical anchors for horizontal and vertical
More informationSECTION CHAIN LINK FENCING
SECTION 32 31 13 CHAIN LINK FENCING PART 1 - GENERAL 1.01 SECTION INCLUDES A. The Work specified in this Section consists of furnishing and installing permanent chain link fences and gates in accordance
More informationSECTION CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP
1 1 1 0 1 0 1 0 1 SECTION 1 1 CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP BASED ON DFD MASTER SPECIFICATION DATED /01/ P A R T 1 - G E N E R A L SCOPE The work under this section shall consist of
More informationThe following excerpt are pages from the North American Product Technical Guide, Volume 1: Direct Fastening, Edition 15.
The following excerpt are pages from the North American Product Technical Guide, Volume 1: Direct Fastening, Edition 15. Please refer to the publication in its entirety for complete details on this product
More informationSteel City Comparison & Strategy. vs. T&B Liquidtight Fittings. Andrea Briggs. Associate Product Manager - Conduit & Fittings FOR INTERNAL USE ONLY
Comparison & Strategy Andrea Briggs Associate Product Manager - Conduit & Fittings Liquidtight Fitting Brand Strategy Component Comparisons Summary Liquidtight Fitting Brand Strategy Steel City Liquidtight
More informationMISCELLANEOUS SIGN CONNECTION DETAILS TYPICAL ROUTE MARKER ASSEMBLIES SIGN TO POST MICHIGAN DEPARTMENT OF TRANSPORTATION
5-4" SEE DETAIL I COUPLING BAR ON 3 2-10" CANTILEVER SIGN SUPPORT TYPICAL ROUTE MARKER ASSEMBLIES 5/1 DIAMETER STAINLESS STEEL BOLT AND NYLON INSERT LOCK NUT SELF-ALIGNING STEEL REINFORCING PLATE ( TYPE
More informationAPPENDIX A, UMC STANDARD 6-5 STANDARD FOR INSTALLATION OF FACTORY-MADE AIR DUCTS
STANDARD FOR INSTALLATION OF FACTORY-MADE AIR DUCTS Sealing of fibrous glass duct board to the sheet metal sleeve must be made with glass fabric and mastic, except where operating pressure is less than
More informationNemalux INSTALLATION INSTRUCTIONS APPLICATION 1-4
I N D U S T R I A L rev. A- INSTALLATION INSTRUCTIONS *PENDING* E77827 E77827 APPLICATION MR3 & MR6 Luminaires are suitable for use in the following areas as defined by the National Electrical Code (NEC)
More informationStandard Pole Mount Parabolic Antenna Mounting Instructions 3 ft. (90cm) & 4 ft. (120cm)
495 R Billerica Ave. N. Billerica, MA 01862 USA Tel: (978) 459-8800 Fax: (978) 459-3310 / 8814 www.radiowavesinc.com email: sales@radiowavesinc.com Standard Pole Mount Parabolic Antenna Mounting Instructions
More informationHARDLOCK NUT RIM & HARDLOCK NUT BASIC
1 Clamp Load [kn] FEATURES OF HARDLOCK NUT Reusable without reduction in performance! Full torque management and completely fastened even with ZERO (0) clamp load! Available in various materials and surface
More informationNote Pad Holder. Tools:
Note Pad Holder Name: Date: Description: The note pad holder is a cold metal project that involves layout skills and sheet metal fabrication skills Materials: 3 1/8 x ¼ Aluminum Pop Rivet 18 ga. Galvanized
More informationMANHOLES PART I: GENERAL. A. Precast Concrete Manholes
MANHOLES PART I: GENERAL A. Precast Concrete Manholes 1) Manholes shall be made of precast concrete sections of which the top section shall be eccentric or flat slab top. The bottom section shall be a
More informationStargrip series 3000 Mechanical Joint Wedge Action Restraint for Ductile Iron Pipe
Stargrip series 3000 Mechanical Joint Wedge Action Restraint for Ductile Iron Pipe INFORMATION The Stargrip Mechanical Joint Restraint System is a unique product with a proven design that provides an exceptional
More information1.1 SUMMARY. A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards.
PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards. B. See Division 5 Section "Pipe and Tube Railings"
More informationONE-LOK Series SLC/SLCE Pipe Restraint for AWWA C909 PVC Pipe
ONE-LOK Series SLC/SLCE Restraint for AWWA Use the SIGMA ONE-LOK Series SLC/SLCE restraint for AWWA pipe at mechanical or push-on joint ductile iron fittings. The ONE-LOK Restraint Systems can successfully
More informationAUXILIARY FRAMING AND ACCESSORIES
CUSTOM CABINETS & RACKS STRUT AND ACCESSO- RIES JUNCTION KITS ANGLE AND BRACE KITS SPLICE KITS BRACE KITS INSTALLATION KITS WALL ANGLE KITS RUBBER END CAPS SUPPORT INSTALLATION AND SUPPORT KITS STANCHION
More informationINSTALLATION INSTRUCTIONS 3 ROUND & 4 OVAL SIDEBAR (90-DEG BENT END) DODGE RAM MEGA CAB PART NUMBER SB1214S SB1214B
INSTALLATION INSTRUCTIONS PART NUMBER SB1214S SB1214B PARTS LIST: Qty Description Qty Description 1 Driver/Left Sidebar 4 12mm x 32mm OD x 3mm Flat Washers 1 Passenger/Right Sidebar 4 12mm Lock Washers
More informationAssembly and installation help
Assembly and installation help A supplement to the directions The Purpose of this tutorial is to expand (not replace) upon the directions that come with the system and to help provide shortcuts, the first
More informationGlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationThe Saddle Rack. For Power And Communication Cables
The Saddle Rack For Power And Communication Cables Underground Devices SADDLE RACKS: Low Cost, But Tough and Non-Corrosive For Temporary Support or Permanent Installation For Use in Manholes, Handholes,
More informationTENANT IMPROVEMENT 16 FEBRUARY WEST 27TH STREET, 4TH FLOOR 100% CD OWNER/BID ADD 1-03/08/2018
SECTION 055000 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationConduit End Bells...EA1 Hex Reducing Bushings...EA2 Conduit Hubs...EA3-EA4. Split Couplings...EA5 Three Piece Couplings...EA6 Conduit Nipples...
SECTION E INDEX Product Description Page Number Conduit End Bells.......................................EA Hex Reducing Bushings..................................EA2 Conduit Hubs......................................EA-EA4
More informationSECTION COMMON WORK RESULTS FOR HVAC
SECTION 23 05 00 COMMON WORK RESULTS FOR HVAC PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Ball Valve. 2. Hangers and Supports. 3. Identification Tags and Sleeves. 1.2 INCLUDED SECTIONS A. Section
More informationMODEL 83 Pail Handler
MORSE MFG. CO., INC. 727 West Manlius Street P.O. Box 518 East Syracuse, NY 13057-0518 Phone: 315-437-8475 Fax: 315-437-1029 Email: service@morsemfgco.com Website: www.morsemfgco.com COPYRIGHT 2005 MORSE
More informationPeco Fasteners 3/8 Internal Plug Drop In 50 Per Jar 3/8-16 SMART DROP IN ANCHOR ZINC
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-794 Fax: 936-560-4685 Catalog Number Manufacturer Description Weight per unit Product Category 6337J 3/8-6 Smart Drop In Zinc Peco Fasteners,
More informationSTEEL PIPE GUIDERAIL 01/01/
NOTES PIPE RAILING & POSTS: Pipe Rails and s shall be in accordance with ASTM A5 Grade B for standard weight pipe and ASTM A500 Grade B, C or D or ASTM A50 for structural tube. Bars for handrail supports
More informationAssembly and Installation Manual Pontoon Bunk & Side Guide Kit for 4000/5000 Vertical LIFT MCD p/n
Assembly and Installation Manual Pontoon Bunk & Side Guide Kit for 4000/5000 Vertical LIFT MCD p/n 1547-01 A. Intended Use The Metal Craft Pontoon Bunk and Side Guide Kit are intended for pontoon boats
More informationM4 Hex Nut [ ] M4 T-Nut 20 [20-044] Appx. 1. 3mm. 20 Series profiles (1 per hole) (1 per hole) Ordering Information
Handles & Light Duty PA 20 1 Assembly of Hinge M4x8 FHCS [24-208-4] M4 T-Nut 20 [20-044] M4 Hex Nut [24-706-4] 60 300-0 PA 20 on panel 2 Hinge positions 3-4 Clearance dimensions 5 Range of swing FOR M4
More informationGlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationPLAY HOUSE IMPORTANT
IMPORTANT Page 1 PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING ASSEMBLY. All equipment must be installed in accordance with these instructions. Check your shipment against Bill of Lading and Parts list.
More informationConduit Fittings Accessories / GI Conduit Fittings Accessories
Conduit Fittings Accessories / GI Conduit Fittings Accessories We manufacture and export Conduit Fittings Accessories. Our range of Flexible Conduits also includes GI Conduit Fittings Accessories. Boxes
More informationinstallation guide 1 GUIDE#: pwb-assault-001
assault WAKEBOARD tower installation guide INSTALLATION SUPPORT 1 important information This Aerial wakeboard tower fits motor boats with 76-108 inch wide beam widths. This measurement is taken from the
More information17MAY18 U.S. RACK, Inc Falcon Drive, Madera, CA
17MAY18 U.S. RACK, Inc. - 2850 Falcon Drive, Madera, CA 93637-559-661-3050 INSTRUCTIONS for FIFTH WHEEL RACK Model 2010-4AD WARNING: Do NOT attempt to install or use this rack without following all instructions.
More informationFasteners. Fastener. Chapter 18
Fasteners Chapter 18 Material taken from Mott, 2003, Machine Elements in Mechanical Design Fastener A fastener is any device used to connect or join two or more components. The most common are threaded
More information