LPM Series INSTALLATION INSTRUCTIONS. instructions cover all series from LPM110-LPM WIRE HARNESS (3-PRONG) PM300. LPM Series Includes
|
|
- Regina Hamilton
- 6 years ago
- Views:
Transcription
1 LPM Series INSTALLATION INSTRUCTIONS The Command Access Latch Pullback retracts the latch for push/pull operation. These instructions cover all series from LPM110-LPM188. LPM 72 WIRE HARNESS (3-PRONG) C. 72 WIRE HARNESS (3-PRONG) B. PM WIRE HARNESS (2-PRONG) C. 24 VDC Power Supply A. LPM Series Includes A. LPM B. PM300 C. 2- Power Leads U.S. Customer Support Visit our website for more details 1 Canada Customer Support Doc # xxxxx rev.x
2 Standard Placement Module Ceiling Tile Hinge Option Only Module LPM1 Series Installation Example Standard Placement Optional Placement Note: For LPM1 series option placement is only recommended for Hollow metal doors. For wood doors, use standard placement above ceiling tile or in junction box. 1. The door must be prepared with a standard type 86 mortise lock preparation and a 3/8 wire raceway. Be sure that the mortise pocket and the raceway are clear of debris prior to installation. 2. Install the 3-prong, 72 wire harness through the wire raceway leaving enough slack to quick connect to the mortise chassis. 3. Install PM300 at the hinge jamb side of the door within 120 of the lockset. Connect the 3-prong wire harness to the PM300 and hard wire it directly to the harness from the lockset (if using an electric hinge or other transfer device, use 18ga wire). 4. Connect the 2-prong input power wires (BLACK and BLACK) of the PM300 to the 2-prong, 72 wire lead. Then connect the 72 wire lead directly to the wire run coming from the 26.5VDC power supply (not included). The power supply may be up to 300 feet away (see power supply wiring instructions). Note: these wires are not polarity sensitive. 2
3 For Lever Control Solenoid on LPM models Only All other models skip to next page Step 1 - The door must be preped according to origional manufactures template, machined with a 3/8 wire raceway, & preped for a energy transfer hinge. Make sure the mortise pocket is free of debris. Step 4 - Connect the wires exiting the mortise pocket to the Bridge Rectifier (included). Bridge Rectifier ETH Hinge Step 5 - Connect the Bridge Rectifier to the plug exiting the mortise chassis. 3/8 Wire Raceway Bridge Rectifier Step 2 - Run the wires from the ETH hinge through the 3/8 raceway starting at the ETH hinge & exiting into the mortise pocket. Plug Step 6 - Carefully slip the connected mortise lock chassis into the mortise pocket paying close attention not to pinch any wires 3/8 Wire Raceway Wire Transfer Hinge Step 7 - Mount the chassis per manufacturer s instructions. Step 3 - Screw the ETH hinge to the door. At this time DO NOT connect the hinge wires on the jamb side to the wires coming from the power supply. Step 8 - Connect the wires from the power supply at the ETH hinge on the jamb side. Connect the hinge to the jamb. EU (Fail Secure) Bridge Rectifier Energy Transfer Hinge Switch EU (Fail Secure) 12VAC/DC or 24VAC/DC Power Supply EL (Fail Safe) Bridge Rectifier Energy Transfer Hinge Switch EL (Fail Safe) 12VAC/DC or 24VAC/DC Power Supply 3
4 Handing Instructions for LPM STEP 1: Locate the handing screw. This screw is used to hand the handles. The ing side is opposite the screw. LH/LHR STEP 2: To hand the latchbolt, remove the faceplate. Pull the latchbolt out of the chassis and rotate, then release. The latchbolt is spring loaded and will return on it s own. RH/RHR Rotate 180 Deg. Handing Screw Template for non-deadbolt & deadbolt 1-1/4 diameter cylinder hole for exterior side only (Optional for deadbolt function) 5/8 diameter thumb turn hole for interior side only 3/8 diameter 1 diameter 3/8 diameter 2-7/32 2-3/4 3-9/32 4-7/16 2-9/ / /32 2-1/4 6-1/8 4
5 Latch Retraction Operating Voltage Range: 24 VDC +/- 10% Hold Current: VDC Surge Current: 1.6 A for VDC Peak Current: 7 24 VDC Input wires to PM300 : Non-polarized Black (+)(-) TECHNICAL INFORMATION Specifications Output wire from PM300: Yellow=Pull Coil; Orange= Hold Coil; Green=Common Lever Control Operating Voltage Range: Switches 24VAC/DC 350mA 12VAC/DC 700mA REX: Green - Common (C) Blue - Normally Open (NO) Gray - Normally Closed (NC) LBM: Green/Black - Common (C) Blue/Black - Normally Open (NO) Gray/Black - Normally Closed (NC) Wire Run Guidelines: For best results we recommend that your maximum wire run not exceed the following: 18ga.= ga. = ga. = ga. = Power Supply for PM300 and PM300D in High Output Mode: In High Output mode, the PM300 is designed for & MUST BE powered by the Command Access PS1, PS5-4, or PS5-6 power supplies only. Troubleshooting & Diagnostics Check the Module is on High Output. Confirm that power supply is a Command Access PS1, PS5-4, or PS5-6 U.S. Customer Support Visit our website for more details 5 Canada Customer Support Doc # xxxxx rev.x
Installation Instructions for 45HW & 47HW Electrified Mortise Locks
Installation Instructions for 45HW & 47HW Electrified Mortise Locks Contents These installation instructions describe how to install your 45HW & 47HW Electrified Mortise Lock. Topics covered include: Finishing
More informationInstalling Your Electronic Deadbolt
Ultra Security Plus Electronic Deadbolt Installation Instructions http://www.hberger.com/video-gallery/electronic-deadbolt New Installation Lock Location Preparation (Skip this section if you door has
More information8500 Series. The fire-rated, concealed electric strike solution for mortise locksets. Available At. Click Here FOLGER ADAM HES INTEGRATED PRODUCTS
Available At Click Here CABINET LOCKS ACCESSORIES The 8500 series is a fire rated, compact, high performance electric strike featuring a unique concealed design for use with mortise locksets without a
More information* * 98/9950WDC. Fire-Rated Devices include these. additional components. 1-Point Latch (LBL)
*24739468* 24739468 98/9950WDC Installation Instructions 1-Point Latch (LBL) Fire-Rated Devices include these additional components Metal Edge Wrap required for 60 and 90-minute applications 2-Point Latch
More informationCertification Exhibit FCC ID: U4A-SCYPROX2 IC: 6982A-SCYPROX2. FCC Rule Part: IC Radio Standards Specification: RSS-210
Certification Exhibit FCC ID: U4A-SCYPROX2 IC: 6982A-SCYPROX2 FCC Rule Part: 15.225 IC Radio Standards Specification: RSS-210 ACS Report Number: 09-0176 - 15C Manufacturer: Assa Abloy, Inc. Model: Bored/Exits,
More informationHES Series Electric Strikes & Optional faceplates 1006 Grade 1 electric StrikeS series optional faceplates AD: E Option
1006 Series Electric Strikes & Optional faceplates 1006 Grade 1 electric StrikeS with K Option The strongest and most versatile electric strike that meets or exceeds every standard developed for electric
More informationInstallation Instructions
Installation Instructions 8000/8300 Series Electric Strike Product Components HES, Inc. 22630 N. 17th Ave. Phoenix, AZ 85027 800-626-7590 www.hesinnovations.com 1 1 2 8000/8300 Electric Strike Body Sticky
More informationINSTALLATION INSTRUCTIONS Z7800 SERIES MORTISE LOCK
801 Avenida Acaso, Camarillo, Ca. 93012 (805) 494-0622 www.sdcsecurity.com E-mail: service@sdcsecurity.com A. Door Preparation: INSTALLATION INSTRUCTIONS Z7800 SERIES MORTISE LOCK 1. Measure desired height
More informationInstallation Instructions
VON DUPRIN Installation Instructions 98/9947WDC Concealed Vertical Rod Exit Device Wood Door Applications Devices covered by these instructions: 98/9947WDC Concealed Vertical Rod Device 98/9947WDC-F (Fire)
More informationInstallation Instructions for 45H & 47H Mortise Locks
Installation Instructions for 45H & 47H Mortise Locks Contents These installation instructions describe how to install your 45H & 47H Mortise Lock. Topics covered include: Finishing the preparation...
More information1006CLB 12VDC or 24VDC Fail secure 12V-45mA, 24V-25mA
1006 Series U.L. Fire Door Listed (10C) U.L. Burglary Resistant Listed (1034) Price Book Date - February 1, 2016 1006 COMPLETE PACS for LATCHBOLT LOCKS BLK 630 1006CLB 12VDC or 24VDC Fail secure 12V-45mA,
More informationThe strongest, most versatile electric strike available
Series electric strike shown with N option We offer several types of faceplate options to accommodate your application. Faceplate options sold separately (see pages 5-10). 1006 series shown with J option
More informationSERIES 6000 ELECTRIC STRIKES
SERIES 6000 ELECTRIC STRIKES Electric Strikes provide remote release of a locked door. They allow the door to be opened without retracting the latchbolt. This occurs by the releasing of the electric strike
More informationCM5500 COMPUTER MANAGED MORTISE LOCK HARD-WIRED (FSE/FSA) INSTALLATION MANUAL
The 5500 series lock is a stand-alone, microprocessor controlled, electromechanical locking system. The 5500 employs a heavy-duty mechanical design with fewer moving parts that a standard mechanical mortise
More informationFor New or Retrofit Construction Retrofits Existing ANSI 4-7/8 Strike Prep No Centerline Relocation
CM RETROFITS EXISTING ANSI 4-7/8 STRIKE PREP NO CENTERLINE RELOCATION UNIFLEX 55 SERIES UNIVERSAL APPLICATION STRIKE 55-A For cylindrical locksets and locksets with ANSI centerline latch entry with up
More informationINSTALLATION INSTRUCTIONS Z7800 SERIES MORTISE LOCK
801 Avenida Acaso, Camarillo, Ca. 93012 (805) 4940622 www.sdcsecurity.com Email: service@sdcsecurity.com A. Door Preparation: INSTALLATION INSTRUCTIONS Z7800 SERIES MORTISE LOCK 1. Measure desired height
More informationCM5100 COMPUTER MANAGED CYLINDRICAL LOCK HARD-WIRED (FSE/FSA) INSTALLATION MANUAL
The 5100 series lock is a stand-alone, microprocessor controlled, electromechanical locking system. The 5100 employs a heavy-duty mechanical design which is easy to install and highly reliable. The FSE
More informationDB1000 SERIES. Heavy-Duty Tubular Grade 1 Deadbolts. Standard Features. Optional Features. Options
DB1000 SERIES Heavy-Duty Tubular Grade 1 Deadbolts Standard Features n Performance Complies with ANSI A156.5, Grade 1, 250,000 cycles n Chassis Tubular, steel n Deadbolt 1" x 2-1/4", square corner faceplate,
More informationInstallation Instructions For The 8850FL Series Mortise eboss
Installation Instructions For The 8850FL Series Mortise eboss Electronic Battery Operated Security Solution FEATURES Battery Operated (Hardwire Capable) Motorized Grade 1 Mortise Lock 94 User Code Capacity
More informationThe strongest, most versatile electric strike available
1006 Series The strongest, most versatile electric strike available 1006 Series shown with J option The 1006 series is the strongest and most versatile electric strike available. It meets or exceeds every
More information120x165mm. 85x165mm TEMPLATE. ELECTRONIC DEADBOLT model no.: & & Toll-free Number:
20x65mm 85x65mm ELECTRONIC EABOLT FOR BACSET 2 3/4" ( 70 mm) FOR BACSET 2 3/8" ( 60 mm) Ø 2 /8" ( 54 mm ) Toll-free Number: -800-268-659 IMPORTANT: Please read this manual carefully before installing this
More informationSteel Hawk 4300 Electrified Deadlatch (elatch)
STEEL HAWK 4300 ELECTRIFIED DEADLATCH (ELATCH) DA-1 STEEL HAWK 4300 ELECTRIFIED DEADLATCH (ELATCH) Steel Hawk 4300 Electrified Deadlatch (elatch) Operation Turn key, apply voltage, or operate handle or
More informationInstallation & Programming Guide
Installation & Programming Guide EMTouch & EMTouch Classic Style Electronic Deadbolt Locksets EMTouch EMTouch Classic Style ASSA ABLOY, the global leader in door opening solutions What s in the Box 4a
More informationTRILENNIUM FULL SCOPE (FS) TEMPLATE INSTRUCTIONS
Overview Parts Included in Template System: Full Scope (FS) Template Rails, with ø 2-1/8 Crossbore Guides. FS Router Carrier (for 1-3/4, 2 & 2-1/4 Doors) FS Bridges, Stops and Twist Bolts 13/16 x 5 Router
More informationEntry Mortise Handleset
1. Pencil 2. No. 2 and No. 3 Phillips Head Screwdrivers 3. No. 1 and No. 2 Slotted Screw Drivers 4. 1/8" Allen Head Wrench 5. 3/4" Wood Chisel or Corner Chisel 6. Measuring Device 7. Lock Mortising Tool
More informationInstallation Instructions
Installation Instructions 8000/8300 Series Electric Strike Product Components HES, Inc. 22630 N. 17th Ave. Phoenix, AZ 85027 800-626-7590 www.hesinnovations.com 1 1 2 8000/8300 Electric Strike Body Sticky
More informationEntry Mortise Lock Set Lever to Lever
Entry Mortise Lock Set Lever to Lever 1 Lever 2 Escutcheon 3 Turn Piece 4 Mortise Lock 5 Scalp 6 Mortise Lock Strike 7 Mortise Lock Dust Box 8 Mortise Cylinder 9 Cylinder Swing Cover 10 Spindle 11 Spindle
More informationNM SERIES. Extra Heavy Duty Mortise Locks Grade 1
NM SERIES Extra Heavy Duty Mortise Locks Grade 1 1 Auxiliary latchbolt Available with Interchangeable Core. Electrified Locks available upon request. 2 N SS TS JS GS 4 4 ¾ 5 ¼ 4 ¾ 2 9 /16 2 2 15 /32 2
More informationOVERVIEW. Mounting Post (2 places) Cylinder Cam. Handing Pin
DEVICES COVERED IN THIS DOCUMENT: 46CE Cylinder Escutcheon Key locks and 46DT Dummy Trim Pull when dogged unlocks lever 46BE Blank Escutcheon Always operable 46NL Night Latch Key retracts latchbolt 46NK
More information98/9927. Devices covered by these instructions: Surface Vertical Rod Exit Device
911375-00 Surface Vertical Rod Exit Device 98/9927 Installation Instructions Devices covered by these instructions: 98/9927 Surface Vertical Rod Exit Device 98/9927-F (Fire) Surface Vertical Rod Exit Device
More informationINSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET
HIGH EDGE 2 1/4"(57mm) 03079400070 INSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET IMPORTANT: THIS LOCK IS NON-HANDED. LOCK IS FACTORY PACKED PREADJUSTED FOR 1³ ₄" (45mm)
More information98/ Customer Service # Dogging Key (use to lock down pushbar)
911373-00 Rim Exit Device 98/99 Installation Instructions Dogging Key (use to lock down pushbar) Customer Service 1-877-671-7011 www.allegion.com/us Allegion 2014 Printed in U.S.A. 911373-00 Rev. 05/14-f
More informationElectric Strike Complete with LB option includes faceplates that accommodate J, K, KM or KD options
1006 Series U.L. Fire Door Listed (10C) U.L. Burglary Resistant Listed (103) 1006 Complete Pacs For Latchbolt Locks BLK 630 1006CLB 12VDC or 2VDC Fail secure 12V-5mA, 2V-25mA Electric Strike Complete with
More informationED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS
ED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS Ver.2 1300 SERIES CONCEALED VERTICAL ROD DEVICE Top Strike Latch Screws Strike Screws Release Plunger Top Latch Plunger Screws
More informationINSTRUCTIONS FOR HIT TEMPLATE FOR SALTO XS-4 MORTISE & CYLINDRICAL LOCKS
1825 VIA BURTON ANAHEIM CA 92806 714-772-5202 / FAX 714-772-2302 EMAIL: MAIL@MAJORMFG.COM WEB: WWW.MAJORMFG.COM INSTRUCTIONS FOR HIT-66-268 TEMPLATE FOR SALTO XS-4 MORTISE & CYLINDRICAL LOCKS WHEN USING
More informationNo. 059FL. No. 251FL. No. 260FL. No. 305RE. Etruscan Bronze. Florentine Brass. Siena Brass (D) All designs available in these finishes.
SINCE 1964 No. 059FL No. 251FL No. 260FL No. 305RE 2 Etruscan Bronze (ETR) Florentine Brass (D) Siena Brass (BAS) Venetian Nickel (BPS) All designs available in these finishes. No. 309RE No. 331FL No.
More informationSafety glasses Measuring tape Level Pencil Power drill Center punch Phillips screw driver Saw horse
EX76 Concealed Vertical Rod Exit Device Preparation Guide and Installation Instructions Box Contents EX76 Concealed Vertical Rod Exit Device Back Bar Active Push Bar Filler Plate Door Kit with Templates
More information1790 Touchbar. Installation Instructions. Rim Panic Device ININST Index:
Installation Instructions ININST.1001 1790 Touchbar Rim Panic Device Index: Before Installation... 2 Installation... 2 Touchbar Dogging... 7 RM170 Mullion Installation... 8 Field Sizing Device... 10 2090
More informationHeadline. Push/Pull Latches
Headline Push/Pull Latches Quality hardware for superior door control 2 Glynn-Johnson has been providing the highest quality door control hardware for 75 years. Glynn-Johnson uses only state-of-the-art
More informationAdams Rite. Standard & Heavy Duty Deadlatches Series Heavy Duty Deadlatch
Standard & Heavy Duty Deadlatches 4900 Series Heavy Duty Deadlatch Function: Flexibility of traffic control and installation is offered by the 4900 Series Deadlatches. A reverse turn of the key while bolt
More information1006 Series + = Non-handed Trim adapter (goof plate) 5 year limited warranty
1006 Series The 1006 Series is the strongest and most versatile strike available. It meets or exceeds every standard developed for electric strikes. With 27 faceplate options, the 1006 can accommodate
More informationPMR ELECTRONIC LOCK USER GUIDE
封底 封面 148.5 x 210(mm) www.ezset.com.tw PMR ELECTRONIC LOCK USER GUIDE 封面裡 Parts Introduction Do not use an electric screwdriver when installing the product! Installation Procedures 1. Draw horizontal lines
More informationElectric Strikes. Overview
Electric Strikes Overview Electric strikes are electromechanical door locking devices that are installed in place of the conventional lock strike plate. They are used in conjunction with mechanical locksets
More informationPassage Mortise Lock Set Lever to Lever
Passage Mortise Lock Set Lever to Lever 1 Lever 2 Escutcheon 3 Mortise Lock 4 Scalp 5 Mortise Lock Strike 6 Mortise Lock Dust Box 7 Spindle 8 Spindle Spring 9 Spindle Retainer 2 1 9 8 7 9 7 8 3 1 2 4 5
More informationHeadline Push/Pull Latches
Push/Pull Latches Quality hardware for superior door control Glynn-Johnson has been providing the highest quality door control hardware for over 75 years. Glynn-Johnson uses only state-of-the-art technology
More informationDoor Hardware Installation Instructions. For Assistance Call:
For Assistance Call: Door Hardware Installation Instructions Single Cylinder NOTE: s fit doors 1-3/4 to 2-1/4 thick. For thicker doors, please call customer service. Carefully unpackage all components
More informationE-PLEX 3X00 SERIES NARROW STILE LOCK INSTALLATION INSTRUCTIONS
E-PLEX 3X00 SERIES NARROW STILE LOCK INSTALLATION INSTRUCTIONS TABLE OF CONTENTS Tools Required.................................................................3 A. Door Preparation - Remove Existing Outside
More informationCATALOG PRICELIST HES ELECTRIC STRIKES AND ACCESSORIES 2011 HES AND FOLGER ADAM ELECTRIC STRIKES AND ACCESSORIES
2011 HES AND FOLGER ADAM ELECTRIC STRIKES AND ACCESSORIES HES ELECTRIC STRIKES AND ACCESSORIES CATALOG PRICELIST ASSA ABLOY, the global leader in in door opening solutions About At Hanchett Entry Systems,
More informationCRCODE-202. Mechanical Lock. Instruction and Programming Manual. Before Installing:
CRCODE-202 Mechanical Lock Instruction and Programming Manual Before Installing: 1. Please read the instructions carefully to prevent missing important steps. *Note: Improper installations may result in
More informationExit Device 5820 SERIES GRADE 1 PUSH BAR SPECIFICATIONS HEAD COVER OPTIONS STRIKES APPLICATION.
Exit Device 5820 SERIES GRADE 1 PUSH BAR 5820F Fire-Rated Mortise Lock Exit Device 5820FSF Failsafe Electric Mortise Exit Device 5820FS Failsecure Electric Mortise Exit Device HEAD COVER OPTIONS HC-1 HC-2
More information33/3550AWDC. Fire-Rated Devices include these. additional. components. 1-Point Latch (LBL) Metal Edge Wrap required for 60 and 90-minute applications
24739476 33/3550AWDC nstallation nstructions 1-Point Latch (LBL) Fire-Rated Devices include these additional components Metal Edge Wrap required for 60 and 90-minute applications 2-Point Latch includes
More informationInstallation Instructions For Profile Series v.g1 Exit Device
Installation Instructions For Profile Series v.g1 Exit Device A7757C Copyright 2004, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part
More informationM O R T I S E L O C K S
MORTISE LOCKS lock design M certification / compliance Locks comply with UL 10B, Fire Tests of Door Assemblies, and UL 10C, Positive Pressure Fire Tests of Door. Door Assemblies and the Uni form Building
More information12 24 VAC/VDC ±10% (inhibited when voltage is applied) min. pulse width duration = 50 ms. Normal mode or Background Analysis mode
DESCRIPTION SUPERSCAN-T Door-Mounted, Presence Sensor for Automatic, Pedestrian Doors SuperScan-T sensors are intended to be used with pedestrian, swing door systems. ENGLISH 1 1. Lens. Master circuit
More informationHookbolt. Non Handed. Flat LH Bevel RH Bevel Radius Radius with Weather-strip. Radius Flat Bevel
Mortise Locks deadlatch Deadbolt Hookbolt Function: Deadbolt, Hookbolt, Deadlatch Backset: 31/32", 1-1/8", 1-1/2" Face Plate: 1"W x 6-7/8" L - Aluminum Case Dimensions: 7/8"W x 6"L x Depth specific to
More informationSD-996C-NUVQ Electric Door Strike with Vertical Adjustment
SD-996C-NUVQ Electric Door Strike with Vertical Adjustment Manual 43RG Features: 12/24 VDC Operation Vertical adjustable deadbolt opening, sliding shim keeper, and deadlatch ramp accommodates a wide range
More informationSeries. The strongest, most versatile electric strike available FOLGER ADAM HES INTEGRATED PRODUCTS. Specifications
FOLGER ADAM HES ACCESSORIES CABINET LOCKS Shown with KM Option The 1006 series is the strongest and most versatile electric strike available. The dual interlocking plunger design and heavy duty stainless
More information351 DOOR CLOSER WITH DOUBLE LEVER ARM (OP) INSTALLATION INSTRUCTIONS
2 351 DOOR CLOSER WITH DOUBLE LEVER ARM (OP) INSTALLATION INSTRUCTIONS Strength Adjustable From Size 1 Thru 6 CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE Auxiliary door
More informationCM5500 COMPUTER MANAGED MORTISE LOCK INSTALLATION MANUAL
The 5500 series lock is a stand-alone, microprocessor controlled, electromechanical locking system. The 5500 employs a heavy-duty mechanical design with fewer moving parts that a standard mechanical mortise
More informationWNA Series. Knobsets AVAILABLE STYLES AVAILABLE FINISHES. Finish A 26 26D 34 3W BEVERLY HUNTINGTON PHOENIX TROY BHMA Code
WNA Series Knobsets AVAILABLE STYLES Beverly Huntington Phoenix Troy AVAILABLE FINISHES Are in Brilliance finish in certain funtions Finish 3 5 15 17A 26 26D 34 3W BEVERLY HUNTINGTON PHOENIX TROY BHMA
More informationDOOR TECHNOLOGY ORDER CATALOG SECTION SECURY Automatic Door Lock & Gripset Handle
DOOR TECHNOLOGY ORDER CATALOG SECTION 03.3 SECURY Automatic Door Lock & Gripset Handle Table of Contents 03.3 SECURY Automatic Door Lock & Gripset Handle SECURY Automatic Door Lock...03.3.5 Automatic
More informationMEETS ADA REQUIREMENTS!
PUSH / PULL LATCH HL-6 MEETS ADA REQUIREMENTS! HL-6/EO EXIT ONLY LATCH HL-6/EO Exit Only Latch for applications where only one side of door is used for exit or entry. Ideal for situations where the security
More informationThis is a printable pdf document. For Smartphone-friendly version, tap or click here.
This is a printable pdf document. For Smartphone-friendly version, tap or click here. *911373-00* 911373-00 Rim Exit Device 98/99 Installation Instructions Dogging Key (use to lock down pushbar) Customer
More informationDIVISION 8 DOORS AND WINDOWS. 1. Exterior and interior single doors shall be 1-3/4 inch thick, 3 feet wide, and 7 feet high, minimum.
8.01 DOORS AND FRAMES (12-2-02) A. Doors DIVISION 8 DOORS AND WINDOWS 1. Exterior and interior single doors shall be 1-3/4 inch thick, 3 feet wide, and 7 feet high, minimum. 2. Where required for maintenance
More informationConcealed Shallow tab 17.3 (.68) 11 (.44) 86 (3.38) 44 (1.72) 8 (5/16) Hex wrench opening (.252) 2 PL. Receptacle panel. Latch. panel Ø13 (.
22 R2 Draw Concealed Shallow tab High tensile Suited for thin panels Ø 5 (.196) (.).3 (.6).5 Average ultimate tensile : *13.5.5 Average ultimate shear : 900 N (2000 lbf) Install assembly with M5 (No. 10)
More informationFor installation assistance, contact SARGENT at DOORS SHOWN HERE SWING IN FOR ILLUSTRATION PURPOSES ONLY.
SARGENT Installation Instructions for LP8600 x LR8600 & 12-LP8600 x 12-LR8600 Series Low Profile Panic and Fire Exit Devices on Double Egress & Double Doors or LS8600 & 12-LS8600 Low Profile Exit Device
More informationTravel Trailer Latch With Dead Bolt Trailer Latch With Dead Bolt. U.S. Patent No. 5,927,773
60-250 Travel Trailer Latch With Dead Bolt 60-251 Trailer Latch With Dead Bolt Service Manual (Installation and Troubleshooting) U.S. Patent No. 5,927,773 CONTENTS 1. BASIC COMPONENTS 2. INSTALLATION OF
More information10027 S. 51st Street, Ste 102 Phoenix, Arizona (800) Fax:(800)
10027 S. 51st Street, Ste 102 Phoenix, Arizona 85044 (800) 626-7590 Fax:(800) 232-7329 www.adamsrite.com 2012 ADAMS RITE MANUFACTURING CO. 10027 S. 51st Street, Ste 102 Phoenix, Arizona 85044 (800) 626-7590
More informationStage 2: Preparing the door (read in conjunction with Hole Drilling Options on back of Template).
There are three stages to fitting the CL100 mortise case: Stage 1: Marking out the position of the lock. Stage 2: Preparing the door by mortising and drilling holes. Stage 3: Fitting lock, door furniture,
More informationInstallation Instructions ENGLISH
Installation Instructions ENGLISH Interior Latchset PRIVACY (Bed & Bath) PASSAGE (Hall & Closet) PK.5400 Congratulations! With your purchase of this Interior Latchset, you re among a group of discerning
More informationActive Push Bar. Safety glasses Measuring tape Level Pencil Power drill Drill bits: 5/32, 3/4 Center punch Phillips screw driver
EX88 Interlocking Rim Exit Device Preparation Guide and Installation Instructions Box Contents EX88 Interlocking Rim Exit Device Back Bar Filler Plate Active Push Bar Cylinder and Trim Interface Kit Mounting
More informationChapter 9. Windows and Exterior Doors
Chapter 9. Windows and Exterior Doors 9.1 INSTALLING WINDOWS 9.2 INSTALLING EXTERIOR HOUSE DOORS 9.3 INSTALLING SHED DOOR 9.4 INSTALLING EGRESS COMPONENTS Tools needed by volunteers: Hammer Nail apron
More information4000 Series. The Gainsborough 4000 Series Heavy Duty Cylindrical Locksets KEY IN KNOB LOCKSETS
The Gainsborough 4000 Series Heavy Duty Cylindrical Locksets are designed and manufactured for use in commercial buildings, including hotels and offices, but are also ideal for residential entrances and
More informationSeries. The heavy duty, low profile solution for latchbolts. The 1500 Series is also available in a Complete One Box Solution FOLGER ADAM HES
FOLGER ADAM HES The 1500 Series is also available in a Complete One Box Solution 1500 Series The heavy duty, low profile solution for latchbolts ACCESSORIES CABINET LOCKS Shown with 1KM faceplate The HES
More informationTools Required. * When installing on a fire door, please see instructions below. *
CL615 Tubular Mortice Latch with Code Free option CL615 Tubular Mortice Latch with Code Free option Number relating to picture Item 1 Front Plate and handle * 2 Back Plate and handle * 3 Neoprene seals
More information4600 Series Rim Narrow Stile Exit Device Installation Instructions I-ED01162
DEVICES COVERED IN THIS DOCUMENT: 4600 Series Rim Panic Narrow Stile Exit Device 4600 Series Rim Fire Narrow Stile Exit Device OVERVIEW Outside of Door RHR LHR Inside of Door APPLICATIONS 4950 BLADE STOP
More informationSeries. The dynamic, low profile solution for latchbolts and deadbolts Models. The 1600 Series is also available in a Complete One Box Solution
FOLGER ADAM HES ACCESSORIES CABINET LOCKS Shown with 1N faceplate The HES 1600 Series accommodates up to a 1" deadbolt with enhanced vertical cavity spacing and will accommodate every brand of cylindrical
More informationAdams rite. Electric Strikes for exit device, deadlatch or lockset
7400 & 74 SERIES GRADE 1 ULTRALINE electric strikes Adams rite Electric Strikes for exit device, deadlatch or lockset A What is Preload? Pressure is exerted on a door and transferred to the electric strike
More information1. Begin by rolling your window up all the way 2. Remove your door and window handles by unscrewing the flat head set screws behind each handle.
1. Begin by rolling your window up all the way 2. Remove your door and window handles by unscrewing the flat head set screws behind each handle. 3. Remove the 12 screws that attach the steel interior door
More information6200 Series. System Components Series Electric Strikes
6200 Series Strikes for Mortise or Cylindrical Devices Models 6210, 6211, 6211AL, 6211WF, 6212, 6212WF, 6213, 6214, 6215, 6216, 6221, 6222, 6223, 6224, 6224AL, 6225 & 6226 System Components 6200 Series
More informationSeries. The heavy duty, low profile solution for latchbolts. The 1500 Series is also available in a Complete One Box Solution FOLGER ADAM HES
The 1500 Series is also available in a One Box Solution 1500 Series The heavy duty, low profile solution for latchbolts ACCESSORIES CABINET LOCKS Shown with 1KM faceplate The 1500 Series accommodates latchbolts
More informationFLUSHLINE ENTRANCES. Features
OCTOBER, 2006 FLUSHLINE ENTRANCES FEATURES 1 Features Flush appearance with a face sheet of fiberglass reinforced polyester (FRP) or aluminum, that is captured on four sides by integral extruded reglets
More informationINSTRUCTIONS FOR HIT TEMPLATE FOR ALARM LOCK DL3500 MORTISE LOCK
1825 VIA BURTON ANAHEIM CA 92806 714-772-5202 / FAX 714-772-2302 EMAIL: MAIL@MAJORMFG.COM WEB: WWW.MAJORMFG.COM INSTRUCTIONS FOR HIT-66-210 TEMPLATE FOR ALARM LOCK DL3500 MORTISE LOCK WHEN USING POWER
More informationS O L I D B R O N Z E H A R D W A R E the beauty of fine design, the eternity of solid bronze V E N E T O SOLID BRONZE
the beauty of fine design, the eternity of solid bronze V E N E T O dark bronze Saint-Gaudens Hardware is designed to provide lasting service. Made of the highest quality materials and engineered to meet
More informationWorld s Leading Manufacturer Of Traffic Doors. Supplemental Instructions for the Single and Double Door Order Form
World s Leading Manufacturer Of Traffic Doors Supplemental Instructions for the Single and Double Door Order Form World s Leading Manufacturer Of Traffic Doors 2809 SW th Street Redmond, OR 97756 Phone:
More information1431 DOOR CLOSER WITH STANDARD DUTY ARMS (WITHOUT HOLD OPEN) INSTALLATION INSTRUCTIONS 1431 SERIES ADJUSTABLE FROM SIZE 1 THRU 6
1431 DOOR CLOSER WITH STANDARD DUTY ARMS (WITHOUT HOLD OPEN) INSTALLATION INSTRUCTIONS 1431 SERIES ADJUSTABLE FROM SIZE 1 THRU 6 FOR INSTALLATION ASSISTANCE, CALL SARGENT AT 1-800-727-5477 www.sargentlock.com
More informationFinish Hardware. Contents. Section 10
Section 10 Finish Hardware Contents 10.0.0 Introduction to contents 10.1.0 Door hinges (types and illustrations) 10.2.0 Locksets and latchset configurations and functions 10.3.0 Heavy-duty mortise cases,
More informationVictory Fire Door Inspections
Vickie Evans, FDAI Over 30 years in door and hardware industry DHI instructor and Education Advocate Certified Fire Door Inspector To compartmentalize a building Deter the spread of smoke and flames Fire
More informationSERIES. Installation Instructions
7 1 0 4 SERIES Installation Instructions Important: Please keep these instructions. The combination of this lock has been factory preset: 2 and 4 pressed together, then 3. WARNING For your own safety,
More information33/3547A. Special tools needed: #10-24 tap Drill bits: #25, 5/16, 13/32, 1/2
911404-00 Concealed Vertical Rod Exit Device 33/3547A Installation Instructions Devices covered by these instructions: 33/3547A and 33/3548A Concealed Vertical Rod Exit Device 33/3547A-F and 33/3548A-F
More informationPHYSICAL FACILITIES Consultant s Handbook Division 08 Openings 7400 Access Control Hardware. Page 1 of 6
1 Definitions Vending Laundry Copy Office/Retail Outlet Door Switch Controlled Door Card Reader Door LX Switch RX Switch Power Transfer Mortise Type Non- consisting of beverage and/or snack machines to
More informationNARROW, MEDIUM AND WIDE STILE, THERMASTILE AND DURASTILE. Installation Instructions
NARROW, MEDIUM AND WIDE STILE, THERMASTILE AND DURASTILE Installation Instructions PART Y015 JUNE 2016 Table of Contents Section 1. GENERAL NOTES AND GUIDELINES... 2. DOOR HARDWARE A. Locks B. Push/Pulls
More informationINSTALLATION INSTRUCTIONS CRL JACKSON
INSTALLATION INSTRUCTIONS CRL JACKSON 2085 CONCEALED VERTICAL ROD PANIC EXIT DEVICE crlaurence.com Phone: (800) 421-6144 Fax: (866) 921-0531 crlaurence.com usalum.com crl-arch.com 11M0250 ORDER OF ASSEMBLY
More informationINSTRUCTIONS FOR HIT TEMPLATE FOR BEST 34H-37H MORTISE LOCK
1825 VIA BURTON ANAHEIM CA 92806 714-772-5202 / FAX 714-772-2302 EMAIL: MAIL@MAJORMFG.COM WEB: WWW.MAJORMFG.COM INSTRUCTIONS FOR HIT-66-230 TEMPLATE FOR BEST 34H-37H MORTISE LOCK WHEN USING POWER TOOLS
More information33/35A Series. Devices covered by these instructions: Rim Exit Device. CD33/35A Rim Exit Device EL33/35A Rim Exit Device SS33/35A Rim Exit Device
911402-00 Rim Exit Device 33/35A Series Installation Instructions Devices covered by these instructions: 33/35A Rim Exit Device CD33/35A Rim Exit Device EL33/35A Rim Exit Device SS33/35A Rim Exit Device
More informationSCHLAGE SENSE. Smart Deadbolt. Installation Instructions. Download the Schlage Sense app to get started!
SCHLAGE SENSE Smart Deadbolt Installation Instructions Download the Schlage Sense app to get started! Schlage Sense Installation Instructions Package Contents Camelot Style shown throughout guide. Support
More informationInstallation Instructions
for s TOC Table of Contents 1 Mortise Lock Handing Instructions.... 2 2 3 4 5 Mortise Lock Door Preparation & Installation... 3 HSS Trim Installation.... 5 Knob x Knob...6 Lever x Knob....7 Turn-Piece
More information7100(F) series. A conventional exit device for single swing doors or pairs of doors of metal, wood or composite construction.
Page Revised Electronically 12/12 7000 series architectural exit devices introduction Yale 7000 series exit devices deliver an unparalleled combination of durability, breadth of line, innovation and aesthetics.
More informationYour combination is and is not recorded at the factory. This number can be found on the combination slides if required.
3778 South Kalamath Street, Englewood, CO 80110 Phone (303) 762-7373 Fax (303) 484-4070 www.presomatic.com office@presomatic.com Installation Instructions for Deadlatch Models 8200 8200A Congratulations
More informationDOOR SAVERS AVAILABLE IN STEEL, STAINLESS STEEL (32D), BRIGHT BRASS (3), BRONZE (10) AND OIL RUBBED BRONZE (10B)
SAVERS K1 : 9 High For cylindrical locksets 2-1/8 bore, 2-3/8 and 2-3/4 backsets K 188 2-3/8 1-3/8 K 184 2-3/8 1-3/4 K 148 2-3/4 1-3/8 K 144 2-3/4 1-3/4 K5 144 5 SPECIFY K3 : 9 High For cylindrical locksets
More information