FAX: (USA)

Transcription

1 Congratulations on the purchase of your new DMI Sports soccer table. Our products are designed and manufactured to give you years of game playing enjoyment. KEEP BOX AND PACKING MATERIAL UNTIL TABLE HAS BEEN COMPLETELY ASSEMBLED. ALL DAMAGE MUST BE REPORTED TO DMI WITHIN TEN DAYS OF RECEIPT. If you have any problems with your new product, PLEASE DO NOT RETURN IT TO THE STORE. Please contact us: FAX: (USA) Please have your model number when inquiring about parts. Or write to: DMI Sports Customer Service 1300 Virgina Drive, Suite 401 Fort Washington PA, Please visit our web site at: When contacting DMI Sports, please provide your model number and item number (if applicable) if requesting a replacement part. Item numbers can be found inside this owners manual. HT60 Series Your Model Number Your model number is also located on the original carton. These instructions are also available online at: DMI Sports -1- For Customer Service Call

2 IMPORTANT! Please Keep Your Instructions! (You will need your Model number should you need to contact us.) Before attempting assembly, please read through this instruction book to familiarize yourself with all the parts and assembly steps. We recommend that two adults assemble this table. Please refer to the Parts Identifier on the following page and be sure that all parts have been included. Although extremely rare, occasionally a part may be missing. If you are missing a part, or if you have any questions, please call our customer service department at Mon-Fri between the hours of 9:00am and 5:00pm E.S.T; or you can reach us at: Do not return the game to the store. Please contact us first at: or on our website at: TWO ADULTS ARE REQUIRED TO ASSEMBLE THIS HOCKEY TABLE DMI Sports -2- For Customer Service Call

3 PARTS IDENTIFIER P1 P2 P3 P4 P5 P6 1 Piece P7 P8 P9 H1 H2 H3 H5 Side Panel With On/Off Slot 1 Piece H7 H10 H11 3/16 Console Bolt F4*1-3/4 Leg Screw 62 Pieces H12 H13 H14 H15 5/16 *1-3/4 Leg Bolt H16 H17 P11 P12 Wrench 1 Piece P13 P3 x 5/8" Screw 4 Pieces P14 P15 Scorer P16 P17 Puck Catcher with Wire P18 Switch Box And Control Plug 1 Piece P19 P20 P21 P22 P23 U Bracket 1Piece P24 Lighting Rail Harness 2Pieces Sensor Wire 2Pieces Goal Box- Puck Return w/ Triangle Catcher Cover Junction Box 1Piece Tools required for assembly: Allen wrench - included Screw driver, electric screw driver preferred - not included Level recommended - not included DMI Sports -3- For Customer Service Call

4 STEP 1. ATTACH APRONS Aprons secure to the table frame with H12 and H13 brackets. P1 H12 H5 H13 H12 H12 P9 P2 H13 H5 H5 P2 P1 Note: Please leave the main frame face down in the carton that it ships in until the aprons and legs are attached. All images are shown up-side-down as the table should be assembled. Please DO NOT step or lean on frame of table while assembling the table. DMI Sports -4- For Customer Service Call

5 STEP 2. ATTACH APRON CORNER BRACKETS AND GOAL BOX Apron corner brackets (P18) slide into place to brace four aprons together. P18 P12 P23 H17 P2 P22 STEP 3. LEG ASSEMBLY H3 H1 H2 P5 P4 P8 P3 P6 P6 H10 H10 P6 P5 P4 P3 After four sides are attached to each other the leg base, P8, is attached with screws (H3). DMI Sports -5- For Customer Service Call

6 STEP 4. ATTACH LEG SUPPORT PANELS & LEGS Attach legs to frame of the table. Do not tighten until the leg support panels are attached to each leg. Once support panels are attached to legs with metal plates (H14) legs can be to the frame. P7 H11 H14 H11 P7 H14 H7 STEP 6. ATTACH CONSOLE Wire the console to each goal and then plug the power cord in to test that scoring matches P11 the console can be secured with screws H7. STEP 5. TURN TABLE OVER Turning table over with the assistance of at least one adult (minimum 2 adults), gradually lift and turn your new hockey table over. Do not rest the weig ht of the table f rame on just two legs as you a re turning table right-sid e-up. DMI Sports -6- For Customer Service Call

7 STEP:6 Attach the On/Off Switch (P17) to the Side Apron (P9) using Screws (). Insert the adapter (P16) into the Plug Box and secure using the U Bracket (P19) and two screws (). Insert the Blower Motor plug into the Plug Box. P17 Power Plug P19 Plug Box Blower Plug P16 STEP:7 Connect goal sensor wires, console wire, adapter wire and rail light wires to junction box as shown. P11 P20 Lighting Rail Harness P24 Lighting Junction Box P16 P21 Sensor Wire P21 Sensor Wire P20 Lighting Rail Harness DMI Sports -7- For Customer Service Call

8 PARTS RE-ORDER FORM Send this form along with your check or money order payable to: HT60 Series Hockey Table DMI SPORTS 1300 Virginia Drive., Suite 401 Ft Washington, PA DATE: NAME: ADDRESS: PHONE CITY: STATE: ZIP CODE: REF QTY PART # DESCRIPTION UNIT PRICE P1 1 RPHT60-P1 SIDE PANEL (ea.) P2 2 RPHT60-P2 END PANEL (ea.) P3 4 RPHT60-P3 LEFT LEG PANEL (ea.) P4 4 RPHT60-P4 RIGHT LEG PANEL (ea.) P5 4 RPHT60-P5 MIDDLE LEG PANEL A (ea.) P6 4 RPHT60-P6 MIDDLE LEG PANEL B (ea.) P7 2 RPHT60-P7 LEG END PANEL (ea.) P8 4 RPHT60-P8 LEG BASE (ea.) P9 1 RPHT60-P9 SIDE PANEL W/ON/OFF SLOT (ea.) H1 24 RPHT60-H1 1/4"*28MM BOLT (ea.) 0.50 H2 24 RPHT60-H2 1/4"*19MM WASHER (ea.) 0.25 H3 16 RPHT60-H3 F4*2" SCREW (ea.) RPHT60-5/16"*1-1/2" BOLT (ea.) 0.50 H5 12 RPHT60-H5 5/16"HEX NUT (ea.) RPHT60-5/16"*19MM WASHER (ea.) 0.25 H7 2 RPHT60-H7 3/16" BOLT (ea.) RPHT60- T4*15MM SCREW (ea.) RPHT60- T4*12MM SCREW (ea.) 0.50 H10 24 RPHT60-H10 F4* 1-3/4" LEG SCREW (ea.) 0.50 H11 12 RPHT60-H11 5/16"*1-3/4" LEG BOLT (ea.) 0.5 H12 12 RPHT60-H12 "U" PLASTIC BRACKET (ea.) 3.00 H13 12 RPHT60-H13 "L" PLASTIC BRACKET (ea.) 3.00 H14 8 RPHT60-H14 METAL LEG PLATE (ea.) 1.00 H15 1 RPHT60-H15 ALLEN KEY (ea.) 1.00 H16 1 RPHT60-H16 WRENCH (ea.) 1.00 H17 4 RPHT60-H17 P3*15MM SCREW RPHT60- LEG LEVELER (ea.) 5.00 P11 1 RPHT60-P11 SCORER/CONSOLE (ea.) P12 2 RPHT60-P12 PUCK CATCHER W/WIRE (ea.) 5.00 P13 4 RPHT60-P13 DELUXE POWER PUSHER (ea.) 4.50 P14 4 RPHT60-P14 HOCKEY FELT (ea.) 0.50 P15 4 RPHT60-P15 PUCK (ea.) 2.50 P16 1 RPHT60-P16 ADAPTER (ea.) P17 1 RPHT60-P17 SWITCH BOX & CONTROL PLUG (ea.) P18 4 RPHT60-P18 APRON CORNER (ea.) 5.00 P19 1 RPHT60-P19 PLASTIC BRACKET (ea.) 3.00 P20 2 RPHT60-P20 LIGHTING RAIL HARNESS (ea.) P21 2 RPHT60-P21 GOAL SENSOR WIRE (ea.) 5.00 P22 2 RPHT60-P22 GOAL BOX/PUCK RETURN (ea.) 8.00 P23 2 RPHT60-P23 CATCHER COVER (ea.) 5.00 P24 1 RPHT60-P24 JUNCTION BOX (ea.) Up to $15.00, add $2.00 for S&H Over $15.00, add $8.00 for S&H Console, add $5.00 for S&H PA Residents Add 6% State Sales Tax: Shipping and Handling Charges: TOTAL: TOTAL AMOUNT DMI Sports For Customer Service Call:

9