TECHNICAL CATALOGUE EXTERIORS

Transcription

1 TECHNICAL CATALOGUE EXTERIORS Prodema NATURAL WOOD BEAUTY

2 EDITION Nº SPECIFIC CATALOGUE FOR 1 EUROPE ASIA AFRICA OCEANIA CENTRAL AND SOUTH AMERICA For the satisfactory installation of ProdEx panels, it is necessary to follow all the instructions contained within this technical catalogue, without exception. For technical queries, alternative installation systems, etc., we recommend contacting Prodema (prodema@prodema.com). The updated version of this present guide can be found on the Prodema website.

3 CONTENTS 1. INTRODUCTION 1.1 CONSTRUCTION KIT CERTIFICATES ENVIRONMENTAL COMMITMENT TECHNICAL DATA SHEETS PRIOR TO INSTALLATION OF THE PRODUCT 2.1 RECEIPT OF MATERIAL HANDLING AND STORAGE RANDOM POSITIONING OF PANELS MACHINING CUTTING RECOMMENDATIONS DRILLING RECOMMENDATIONS INSTALLATION OF THE PRODUCT 3.1 GENERAL CONCEPTS VENTILATED FAÇADES EXPANSION JOINTS DIMENSIONAL STABILITY SUBSTRUCTURE: DIFFERENT STRIP TYPES MINIMUM SUPPORT POINTS PER PANEL TONGUE AND GROOVE AND COUNTERSUNK SCREWS INSTALLATION SYSTEM VISIBLE FASTENING WITH SCREWS OR RIVETS: FAÇADE CONCEALED FIXING WITH CAPS: FAÇADE CONCEALED FIXING WITH HANGING PROFILES CONCEALED FIXING WITH ADHESIVE: FAÇADE FIXED LOUVERS STYLE FASTENING CLAPBOARD FAÇADE STYLE FASTENING UNIQUE FAÇADES UNIQUE SHAPES SUSPENDED CEILINGS MOVABLE LOUVERS POST-INSTALLATION 4.1 REMOVING THE PROTECTIVE SURFACE CLEANING MAINTENANCE REPAIR REMOVAL INFORMATION 5.1 REMOVAL WASTE MANAGEMENT ACCESSORIES 6.1 GENERAL ELEMENTS FOR THE PRIMARY SUBSTRUCTURE ALUMINUM GALVANIZED STEEL SPECIFIC ELEMENTS FOR THE VISIBLE FASTENING SYSTEM WITH... SCREWS OR RIVET SCREWS RIVETS SPECIFIC ELEMENTS FOR THE HIDDEN FASTENING SYSTEM WITH CAPS GENERAL ACCESSORIES FOR THE CAP SYSTEM CAPS SPECIFIC ELEMENTS FOR THE HIDDEN FASTENING SYSTEM WITH HANGING STRUTS GENERAL ACCESSORIES FOR THE HANGING SYSTEM SPECIFIC ELEMENTS FOR THE FIXED LOUVER STYLE FASTENING GENERAL ACCESSORIES FOR THE FIXED LOUVER SYSTEM SPECIFIC ELEMENTS FOR THE AMERICAN FAÇADE STYLE FASTENING SYSTEM GENERAL ACCESSORIES FOR THE AMERICAN FAÇADE STYLE FASTENING SYSTEM CURVES INSTALLATION DETAILS

4 1 INTRODUCTION ProdEX. EXTERIORS ProdEX is a construction kit for the cladding of ventilated façades made up of natural wood panels and the corresponding substructure. Each panel consists of a high density bakelite core, clad in a veneer of natural wood with a surface treated with synthetic resin and an exterior PVDF film, which lends greater durability to the panels, with anti-adherent properties, to protect the panel from solar radiation, atmospheric agents, dirt and the attacks of chemical products (anti-graffiti). Due to its high resistance, it does not require the typical maintenance of other woods for exteriors. ProdEX panels are unique, no two are alike, each grain is different, which explains the difference in tone between them and which gives it a natural and authentic appearance that can be appreciated in the reflection of the light on its wood fibers. At Prodema, we have invested a large part of our resources in constantly improving the quality of our products, subsequently obtaining different certificates of trials performed at independent laboratories. This is because our philosophy of continual improvement obliges us to obtain the most demanding quality certificates, such as the ISO 9001 quality management standard. 6 7

5 DIMENSIONS 1 1 CONSTRUCTION KIT CERTIFICATES ProdEX panels are extremely versatile and can be cut into any shape or size to adapt to the needs of all projects. Always follow the cutting instructions set out in this technical catalogue (see section 2.4). Panel dimensions: Length x width: 2,440 mm x 1,220 mm Thicknesses: 6, 8, 10, 12, 14, 16, 18, 20, 22 mm Panel thickness:, (mm) Weight / unit surface area:,, 20, 8,10 22 mm10,80 13,50 16,20 18,90 21,60 24,30 27,00 29,70 (Kg/m 2) mm Due to the high quality of the ProdEX construction kit, it complies with the most demanding of certifications in different countries. The certificates available are listed below according to country and are available on the Prodema website*. Prodema carries out an exhaustive quality control of ProdEX and offers a 10 year guarantee** for this product. EUROPE IETcc (EOTA MEMBER) European Technical Approval ETA-13/0626 SPAIN IETcc (Instituto Eduardo Torroja de ciencias de la construcción) Ditplus 522-p/08 FRANCE CSTB (Centre Scientifique et Technique du Bâtiment) Avis Technique ProdEX sur ossature métallique GERMANY DIBt (Deutsches Institut für Bautechnik) Allegemeine bauaufsichtliche Zulassung Z UNITED KINGDOM BBA (British Board of Agrément) Agrément certificate 12/4917 RUSSIA NPF Antip Fire safety certificate C-ES. 04.B UNITED STATES ICC-ES Evaluation Service (International Code Council - Evaluation Service) ESR-3439 UNITED STATES Intertek Warnock Hersey SPEC ID certification For panels that are not installed vertically, the guarantee is reduced to 5 years as the surface will age more rapidly as a consequence of the greater angle of incidence to solar radiation and the fact that rainwater may pool on the surface mm Thicknesses: Maximum for the 10 year guarantee = 30º If >30º = 5 years 30º 22 mm 18 mm 14 mm 10 mm 6 mm 90º 20 mm 16 mm 12 mm 8 mm * It is recommended to visit this section of the web page on a regular basis to obtain the latest 8 version of these certificates. 9 ** The general terms and conditions of the guarantee may be altered without prior notice. The certificates displayed here are those available as at the date of printing of this catalogue. For information on the latest certificates obtained, contact Prodema (prodema@prodema.com).

6 1 2 ENVIRONMENTAL COMMITMENT 1 3 TECHNICAL DATA SHEETS At Prodema, we have always been committed to the conservation of the environment and it is with this in mind that we are continually starting initiatives designed to encourage environmental improvements and to be at the forefront of our sector in the innovation and motivation of sustainable practices. By being true to this commitment, we have been able to fulfill real objectives which have resulted in benefits for our clients and society in general. This is how, in 2002, we obtained the ISO in Environmental Management certification for our factory in Legorreta (Spain). This system identifies the different environmental aspects to improve by establishing an action plan. ProdEX Prodema NATURAL WOOD BEAUTY TECHNICAL DATA SHEET 1. INSPECTION 2. DIMENSIONAL TOLERANCES Recently, we have become the first company in our sector in the world to obtain the ISO for ECO design, which identifies the environmental aspects of a product in its design phase and reduces their negative impacts during its life cycle. We also have product environmental statements (ECO labels) in accordance with ISO and NF P01-010, and most recently, since 2007, PRODEMA, S.A. has been PEFC certified, which guarantees that our products are produced using wood from forests that are managed in a social manner and are environmentally sustainable. 3. PHYSICAL PROPERTIES The ProdEX construction kit also provides points in the LEED rating system (Leadership in Energy and Environmental Design), the leading global standard in the certification of green buildings. Our products can also help accumulate points in other rating systems in other markets: Breeam, Casbee, gbtool, green globes, etc. 4. WEATHER RESISTANCE 5. CE SAFETY REQUIREMENTS SUMMARY OF CERTIFICATES Environmental Management System Certificate ECOdesign Management System Certificate Certificate of Conformity of the Forestry Products Chain of Custody UNE - EN ISO GA-2002/0070 UNE - EN ISO ED-0009/2010 PEFC/ The reaction to fire detailed has been obtained in accordance with European Standard EN For further information on the reaction to fire of the product in other places and under different standards, contact Prodema (prodema@prodema.com).

7 ProdEX IGN ProdEX FIREPROOF Prodema NATURAL WOOD BEAUTY TECHNICAL DATA SHEET Prodema NATURAL WOOD BEAUTY TECHNICAL DATA SHEET 1. INSPECTION 1. INSPECTION 2. DIMENSIONAL TOLERANCES 2. DIMENSIONAL TOLERANCES 3. PHYSICAL PROPERTIES 3. PHYSICAL PROPERTIES 4. WEATHER RESISTANCE 4. WEATHER RESISTANCE 5. CE SAFETY REQUIREMENTS 5. CE SAFETY REQUIREMENTS The reaction to fire detailed has been obtained in accordance with European Standard EN For further information on the reaction to fire of the product in other places and under different standards, contact Prodema

8 2 PRIOR TO INSTALLATION OF THE PRODUCT 2 3 RANDOM POSITIONING OF PANELS ProdEX panels, as a result of being manufactured from natural wood, may vary in tones. Therefore, prior to installation, machining, etc., it is recommended to mix them to avoid undesirable aesthetic effects. The steps to follow are detailed below: RECEIPT OF MATERIAL Verify condition of package: In the case of visible damage, leave details on the transporter's delivery note. In the case of hidden damage, notify within 72 hours. No claims will be accepted for transport damage in the event of any of these instructions not being complied with. HANDLING AND STORAGE It is recommended to store ProdEX panels in their original packaging up until the time of installation. In the case of having to repackage any panel, this should be done under the same conditions as the original packaging. During transport, ProdEX panels must be properly flexed, taking into consideration that they easily slide when placed one on top of the other and may deteriorate. They must always be placed horizontally. ProdEX panels must be stored in a closed and ventilated area, at an ambient temperature between 10 25º C and with an air humidity of 30 70%. ProdEX must not be stored vertically, but in a horizontal position with a distance of no more than 800 mm between supports. The floor serving as a support for the pallet must be free of material that may cause damage. It is recommended to avoid exposure of both sides of the ProdEX panel to different humidity and temperature conditions. In the particular case of ProdEX panels which have been fitted with fastening elements (such as tabs for hidden mechanical installation), these must be stored face to face; rear to rear successively, using intermediary wooden or plastic supports placed at a distance of no less than 600 mm apart. 1. Number all the pallets in the place of installation 1, 2, 3, etc., - The pallets must be stored throughout the whole installation process in accordance with the requirements described in the section on storage. 2. Open pallet number 1 and remove two panels - Place these two panels on a flat pallet, leaving a maximum distance of 800 mm between supports. 3. Turn over the third panel from pallet number one without removing it from the pallet. 4. Close pallet number one and store it respecting the packaging conditions established by Prodema so that the panels do not warp. 5. Repeat the same process with the other pallets, selecting them in a random order until 10 to 20 panels have been removed. For example, if there are 20 pallets, remove panels from numbers 1, 8, 13, 15 and Mix the 10 to 20 panels that have been removed and install them within 2 to 3 hours from the time the first panel was removed. 7. Repeat the first six steps until all the panels have been installed. TYPES OF OFF-CUTS Depending on the off-cut selected for the façade, the aesthetic result in the majority of cases summarized as the following two options: A. Installation of slats. B. Installation of complete panel or large pieces. A. INSTALLATION OF SLATS B. INSTALLATION OF COMPLETE PANEL OR LARGE PIECES Once the packaging has been opened, it is recommended to remove only those ProdEX panels that are going to be installed immediately. The remaining panels must then be stored under the same conditions 14 as the original packaging. Where an installation is to be performed using large pieces and differences in tone between are to be avoided, it is recommended to send a sample together with the confirmation of the order. In this 15 These instructions are also valid for off-cuts. manner, the panels will be more homogeneous, although there will always be differences in tone as the panels are manufactured using natural wood. The incorrect storage / hadling of ProdEX panels may cause permanent deformation.

9 2 4 MACHINING CUTTING RECOMMENDATIONS Before adjusting a panel, check the perpendicularity, dimensions and straightness. Cuts made to the exterior panels must be performed using tools with a material toughness of K - 05 and K - 01 (Tungsten carbide / Widia), be well sharpened and avoiding overheating at all times. A. SAW Types of saw: Circular saw blades for wood made from hard material (Widia tip). B. CNC The ProdEX panel can be machined at machining centers with computerized numeric control (CNC) machines. The mills used must be perfectly sharpened and it is recommended that they are used at the following speeds: Cutting speed: 16,000 rpm. Feed speed: 4 m / min. It is very important to avoid any overheating of the machine. It is recommended to adjust the cutting parameters during the milling process to obtain an optimum quality. C. ALTERNATIVE SYSTEMS Approximate parameters for saw disks according to tool type: DIAMETER (mm) TEETH (z) / SPEED (rpm) BLADE THICKNESS (mm) 3,2 3,2 2,2 TYPES OF TEETH Alternating inclined teeth (1) and trapezoidal teeth. (2) (1) (2) Aparte de los sistemas ya indicados anteriormente, existen otras posibilidades de mecanizado, aunque no todas son compatibles con el material. Corte con chorro de agua: este sistema es compatible con los paneles ProdEX, aunque es aconsejable realizar una prueba previa para ajustar los parámetros. Corte por láser: no se recomienda utilizar este sistema con los paneles ProdEX ya que ennegrece y quema la chapa de madera. Positioning the panel The cutting disk must always begin cutting on the good face of the panel. Table saw: the visible face of the panel must be face up. Manual saw: the visible face of the panel must be face down. Height of cutting disk: In order to obtain a clean cut, we recommend that the cutting disk have a clearance of approximately 1 2 cm above the material to be cut DRILLING RECOMMENDATIONS The ProdEX panels are drilled using integral hard metal drill bits or steel bits with tungsten carbide tips (Widia) with a cutting angle greater than 100º. Bits for perforating metal may also be used. In order to avoid any splintering of the material to be drilled, use support plates below the panel and thereby obtain a clean hole, as shown below: BIT BIT 1-2 cm GOOD FACE ProdEX PANEL ProdEX PANEL GOOD FACE SUPPORT PANEL The guideline drilling speeds are indicated below, although they should be considered as reference 16 After cutting: only bearing in mind that whey will vary depending on the tool, its condition, the material and the type of drilling. 17 After machining (cut, drill, mill, bevel, sand and polish, if required), no other treatment for finishing or protection of the surfaces obtained is required. The sharp edges can be smoothed Cutting speed: 16,000 rpm. using sandpaper. Feed speed: 4 m / min.

10 3 3 1 INSTALLATION OF THE PRODUCT GENERAL CONCEPTS VENTILATED FAÇADES Did you know that... the use of a ventilated façade is essential for the assembly of ProdEX panels? To ensure the good performance of this type of panel, it is very important that the differences in humidity and temperature between both faces is minimal. The ventilated facade has several advantages over a conventional façade: Watertight to rain The ventilated façade provides better water-tightness in the rain and stops the water from penetrating into the air chamber. It offers a good diffusion of water vapor from within the building to the exterior. The ventilated façade generates a constant ventilation of air and prevents there being any stagnation of humidity or the insulation from becoming damp. Reduces thermal bridges to a minimum. Improved acoustic insulation Thermal insulation Generates an energy saving of up to 50%* by absorbing less heat in summer and dispersing less heat in winter. Easy assembly and disassembly and a good solution for rehabilitations. Interior insulation of the building in the event of exterior changes of temperature Did you know that... in order to ensure the proper functioning of the ProdEX ventilated façade, there must be an uninterrupted flow of air? For this, the following special points must be taken into account: The air chamber between the panels or enclosure must be a minimum of 20 mm, however, the provisions of national or local regulations must be respected (see point 1.1 of the present catalog). Leave an opening of 20 mm at the lower and upper part of the façade, as well as around doors and windows so that the air can circulate vertically. It is recommended to use only vertical strips as these will not interfere with the air circulation. In the case of using horizontal strips which impede the ventilation in a vertical direction, perforations should be made in these strips beforehand in such a manner so as to allow a ventilation of 20 cm2/m on façade cladding up to a height of 1 m and of 50 cm2/m on façade cladding at a height of 1 m. 20 mm BRACKET VERTICAL STRIP THERMAL INSULATION PRIMARY STRUCTURE OBLIGATORY MIN. AIR CHAMBER 20 mm Solar radiation reflected to the exterior Low transmission of temperature into the interior of the building CIRCULATION OF AIR 20 mm In the summer, or during hot spells, the sun shines on the ProdEX panels instead of on the building. This solar radiation heats the air in the air chamber generating a "chimney" effect due to the change in its density. This generated ventilation avoids the accumulation of heat on the façade, which together with the thermal insulation are the perfect combination to protect the building for atmospheric agents 18 In winter, or during cold spells, the ventilated façade acts as a heat accumulator, given that the 19 air chamber assists in the thermal stability of the system. This ventilated façade construction system together with the thermal insulation prevents the loss of heat of the building. * Depending on which direction the building faces, the insulation used and the numbers of doors, windows, etc.

11 3 1 2 EXPANSION JOINTS DIMENSIONAL STABILITY An expansion joint of 6 8 mm between panels should be taken into account. The joint allows the ProdEX panels the necessary room for any expansion and contraction caused by the movement of the material as a result of changes in temperature and humidity. ProdEX, due to being clad with natural wood, will experience small variations in size as a consequence of environmental temperature and humidity changes. The maximum dimensional variation of the panel in a longitudinal direction is 0.30% and 0.60% in a transversal direction. These small dimensional variations do not affect either the aesthetic nature or the functionality of the panels. It is for this reason that it is very important to take into account the expansion joints indicated by Prodema. 6-8 mm 6-8 mm direction of the grain 6-8 mm 0,30% 0,60% 0,60% MAXIMUM TRANSVERSAL DIMENSIONAL VARIATION 0,30% MAXIMUM LONGITUDINAL DIMENSIONAL VARIATION 6-8 mm 6-8 mm ProdEX is a water repellent material; resistant to vapor, water, snow and ice. However, it not advisable to submerge the corners permanently or for extended periods of time in water as areas of a darker color may appear along the edges of the panel surface

12 3 1 4 SUBSTRUCTURE: DIFFERENT STRIP TYPES Due to ProdEX panels requiring a ventilated façade for their installation, the strips that form the substructure must be installed vertically. The fastening of these strips to the enclosure must be performed using fastening elements suitable for the material used. The substructure must be of an appropriate size according to the usual wind load of the area in such a manner that it fulfills the static requirements. The vertical alignment of the façade will also be taken into account, as well as the chosen fastening system and the thickness and dimensions of the ProdEX panel being installed. Furthermore, the elements that comprise the substructure must be optimally protected against corrosion or decay, regardless of the material or systems used. Wood substructure When a substructure is installed using wooden strips, these strips must be treated. It is advisable to place PVC or closed cell polyethylene foam seals over the support surfaces of the panels to protect, improve and lengthen their useful thereof. This class of substructure is suitable for areas that are dry or with little rain. To resolve that irregularities as a result of the vertical alignment of the building, the adjustable auxiliary elements must be used. Metal substructure In rainy or humid areas it is advisable to use metal strips from galvanized steel or aluminum. In coastal areas, where the effects of the sea are evident, it is advisable to use stainless steel or aluminum struts with an appropriate anodizing treatment. AUXILIARY ADJUSTABLE ELEMENT Recommended distance: 1 m 1 The brackets are fixed to the enclosure using screws and their corresponding sleeve (steel or nylon). 1 The brackets are fixed to the enclosure using screws and their corresponding sleeve (steel or nylon) The strip is fixed to the brackets using austenitic stainless steel self-drilling screws. 2 The strip is fixed to the brackets using special screws for wood. 23 For further information on accessories, see chapter 6 of this catalogue.

13 3 1 5 MINIMUM SUPPORT POINTS PER PANEL Prodema recommends that each panel is supported by the maximum surface area of the substructure as possible for all its assembly systems. The panels must be supported by at least three points, both vertically and horizontally, respecting the diagrams on this page. Also, the maximum distances between fittings described further on in this catalog must also be taken into account, as detailed in the tables with each installation EXAMPLES PIECE DIMENSIONS VISIBLE FASTENINGS HIDDEN FASTENINGS PIECE DIMENSIONS VISIBLE FASTENINGS 2440 VISIBLE FASTENINGS Pieces from 300 to 600 mm Applicable to all panels in general, except in the case of exceptions HIDDEN FASTENINGS HIDDEN FASTENINGS Pieces from 400 to 600 mm INTERMEDIATE STRIP AS SUPPORT * 10 through fasteners are used on an 8 mm thick panel * 15 hanger clips are used on an 10 mm thick panel TONGUE AND GROOVE AND COUNTERSUNK SCREWS As an exception, in the case of the pieces on the following table, two support points in the same direction are sufficient. EXCEPTIONS Prodema does not recommend installing tongue and groove panels for exterior façades. This system is fastened using countersunk screws that prevent the panels from moving, and furthermore, they are only screwed in around the perimeter of the female joint and not the male; which is insufficient for the proper functioning of the ProdEX panels according to our recommendations. PIECE DIMENSIONS VISIBLE FASTENINGS HIDDEN FASTENINGS VISIBLE FASTENINGS Pieces from 100 to 300 mm max HIDDEN FASTENINGS Pieces from 100 to 300 mm TONGUE AND GROOVE SYSTEM 24 25

14 3 2 INSTALLATION SYSTEMS EXPOSED FIXING WITH SCREWS OR RIVETS: FAÇADE This type of installation involves securing ProdEX panels using exposed screws or rivets. The screws and rivets* are made of metal and can be ordered lacquered in the same color as the panels. Distances of the screws and rivets from the corner of the panel 6-8 mm mm WALL THERMAL INSULATION VERTICAL STRIP AIR CHAMBER 6-8 mm mm ProdEX PANEL WITH EXPOSED FIXING (screws or rivets) The screws and rivets* on the corners of the panel must be between 20 and 40 mm from the edge of the panel. The distance between screws or rivets*, both horizontally and vertically along the same line, depends on the thickness of the panel. Recommendation for screws or rivets* for panel fixing For wooden strip Screw: SFS - TW - S - D12-4,8 x 38 (lacquered or unlacquered). THICKNESS (mm) DISTANCE BETWEEN STRIPS (mm) 6** 400 8, contact Prodema **Only for special applications. Contact Prodema. Each piece must have at least 3 support points in each direction. Never use countersunk screws for fastening ProdEX. EPDM When installing the panels with wood strips, it is advisable to include a strip of EPDM to protect the strip. * Rivets are only used on metal substructures, not wood substructures * Rivets are only used with metal substructures, not wood substructures. For further information on accessories, see chapter 6 of this catalogue. For further information on accessories, see chapter 6 of this catalogue.

15 For metal strip With screw: Screw: SFS - SX3 - L x 32 (lacquered or unlacquered). Width of holes for screws / rivets All the holes for the visible fastening support screws of the panels must be 3mm greater than the diameter of the screw finally used, except for the hole in the geometric center of the panel, which must the same size as the screw. The width of the screws allows the panel to expand and contract freely without forcing the screw at any time in a direction perpendicular to its axis. In order to carry out any drilling on the panels, follow the instructions detailed in section of this catalog. according to thickness according to thickness 2440 mm according to thickness according to thickness according to thickness 2440 mm according to thickness center of panel = fixed point With rivet*: Rivets*: SFS - AP (lacquered or unlacquered) mm SFS - AP (lacquered or unlacquered). SFS - AP (lacquered or unlacquered). according to thickness according to thickness according to thickness according to thickness 300 mm The remainder are floating points. center of panel = fixed points Position of screw / rivet when installing the panel When inserting the screw / rivet for fastening the panel, it is of vital importance that this is centered in the hole. It is also very important that the head of the fastener is Parallel completely parallel to the panel surface. * Rivets are only used with metal substructures, not wood substructures For more information on screws, rivets and other installation tools, see chapter 6 of this catalogue.

16 METAL SUBSTRUCTURE WITH SELF-DRILLING SCREW SFS-SX3-L 12-5,5 x 32 mm METAL SUBSTRUCTURE WITH RIVET SFS-AP-16-50XXX FLOATING POINTS Pre-drilled on panel to 8.5 mm. FIXED POINTS Pre-drilled on panel to 5.6 mm. FLOATING POINTS Pre-drilled on panel to 8.5 mm. Pre-drilled on strut to 5.1 mm. FIXED POINTS Pre-drilled on panel to 5,1 mm. Pre-drilled on strut to 5.1 mm. Recommended installation tools: Recommended installation tools: SX centering seat. To ensure the perpendicularity of the screw to the panel, as well as the concentric insertion of the same. E-430 screwdriver. For SX3 screws with IRIUS heads. T20W adapter. For SX3 screws with TORX heads. ZL centering seat. To perform the pre-drilling of the substructure concentrically to that of the wall. Centering seat with integrated bit (recommended). To perform the pre-drilling of the substructure concentrically to that of the wall. AP nozzle. This is fitted to the riveter for the installation of the rivets on floating points. NOTE. In the case of steel strips, marine environments, etc., steel A4 SS0-D15 rivets should be used, together with their corresponding accessories. Recommended torques: Aluminum strip with thickness of 2.5mm: 5 Nm to perforate the strip and fasten the panel. 3 Nm to fasten the panel if the strip is already perforated. SS0-D15 rivet Nozzle for SS0-D15 rivet on floating points. (lacquered or unlacquered). WOOD SUBSTRUCTURE WITH SCREWS SFS-TW-S-D X 38 mm Galvanized steel strip with thickness of 0.8 mm: 5 Nm to perforate the strip and fasten the panel. 3 Nm to fasten the panel if the strip is already perforated. FLOATING POINTS Pre-drilled on panel to 8 mm. FIXED POINTS Pre-drilled on panel to 4.9 mm. Recommended installation tools: 30 T20W adapter. For TW-S screws with TORX heads. 31 For more information on screws, rivets and other installation tools, see chapter 6 of this catalogue.

17 3 2 2 CONCEALED FIXING WITH CAPS: FAÇADE This type of installation is carried out using screws to fasten the ProdEX panels to the substructure, which are covered with mm caps, supplied by Prodema in the same finish as the panels. WALL THERMAL INSULATION Floating point PANEL ProdEX Ø 14,25 mm Ø 7 mm 6 mm mm VERTICAL STRIP AIR CHAMBER Pre-drilling of the panels must be performed according to the drilling instructions detailed in section of this technical catalog. Installation of the panels ProdEX CAP (to cover the fastening screw) Once the panels have been pre-drilled, these are fastened to the substructure using the appropriate screws for the strip type. Metal substructure: DIN 7504N pan head self-drilling, self-threading screw. ProdEX PANEL WITH CONCEALED FIXING (screw + ProdEX cap) Screw diameter: 5,5 mm. Head diameter: 10,8 mm. Length: 32 mm. This installation system is designed for use with ProdEX panels with a thickness of 10 to 12 mm. Installing the substructure In order to install the strips that make up the substructure, calculate the distance between the strips and fastenings, etc. Follow the instructions detailed in sections and of this technical catalogue. The distances between the fastenings vary depending on the thickness of the selected panel. Wood substructure: DIN 7505B pan head screw. Screw diameter: 5 mm. Head diameter: 10 mm. Length: 30 mm. WOOD SUBSTRUCTURE METAL SUBSTRUCTURE THICKNESS (mm) DISTANCE BETWEEN STRIPS (mm) Each piece must have at least 3 support points in each direction. Pre-drilling of the panels In order to install the panels using this system it is necessary to pre-drill the panels as indicated below. Placing caps Once the panels have been fastened, caps are inserted to hide the screw heads. To do so, first fill the existing cavity with a flexible silicon, leaving enough space to accommodate the 2 mm thick cap. To insert the cap and to seat it correctly, it is recommended to tap it with a wooden peg to avoid damaging it. Fixed point Ø 14,25 mm ProdEX CAP PANEL FASTENING PANEL ProdEX SCREW 32 6 mm mm FLEXIBLE SILICON Ø 5,5 mm

18 3 2 3 CONCEALED FIXING WITH HANGING PROFILES The guide struts are horizontal fastenings which are superimposed over the primary aluminum substructure. Self-threading screws are used to fasten the guide strut to the substructure. according to thickness* Recommended distance: m WALL THERMAL INSULATION VERTICAL STRIP AIR CHAMBER The hanging clips are pieces of aluminum that are fastened to the panels on the reverse face using TB-A2 TX 30 Panel screws. As the ProdEX material is very hard, a prior blind perforation must be made to be able to screw in this screw. The hole must have a diameter of mm and must be 1.5 mm deeper than the screw once adjusted. The distances between screws must be measured and have to be at a specific height from the edge of the panel. PERFORATED DEPTH UPPER EDGE LOWER EDGE ProdEX PANEL 2 mm 24 mm 24 mm WITH CONCEALED FIXING (hanging profiles) 58 mm ALUMINUM GUIDE STRIP 45 mm ALUMINUM HANGING HOOK Concealed fastenings with hanging strut allow ProdEX to be installed with screws that cannot be seen from the exterior. This type of mounting can only be achieved with panels with a thickness of 10, 12, or 14 mm. This system consists of aluminum struts (strut and guide) and hanging clips. Leveling panels The main difficulty in the installation of the panels with a hanging strut consists of aligning the panel at its height. The hanging clips allow a screw to be added that permits the easy leveling of the panel at its height once it has been installed on the façade. = PROVISIONAL HEIGHT LINE DURING INSTALLATION = CORRECTED HEIGHT LINE LEVELING SCREW ALUMINUM GUIDE STRIP LEVELING PIN ALUMINUM HANGING HOOK SCREW PANEL TB - A2 TX30 Fastening panels Once the panels have been leveled, they can be fastened to prevent any lateral movement. The fastening of panels or pieces must be performed once they are correctly leveled and in their definitive position. ProdEX PANEL 10 mm : CORRECTED ANGLE FASTENING SCREW LEVELING SCREW * See table on page 36. Fastening is carried out by inserting an austenitic stainless steel selfdrilling screw and fastening the ProdEX PANEL 10 mm upper central clip of each panel or piece to the horizontal guide strip. For further information on accessories, see chapter 6 of this catalogue.

19 Installing the horizontal guides The aluminum guide strips are installed horizontally over the substructure according to the thickness* of the panel, provided that the number of aluminum guide strips per panel is a minimum of three CONCEALED FIXING WITH ADHESIVE: FAÇADE Hidden fastening with adhesive allows for the installation of ProdEX panels by using a glue system that consists of cleaning agent, primer, double-sided tape and flexible monocomponent adhesive. VERTICAL STRIP ACCORDING TO THICKNESS* ProdEX PANEL FIXED WITH 3 GUIDE STRIPS HANGING HOOK WALL THERMAL INSULATION VERTICAL STRIP AIR CHAMBER ACCORDING TO THICKNESS* DOUBLE SIDED ADHESIVE TAPE * See table at the end of this page. As an exception, for pieces of between 150 and 400 mm, two guide strips are sufficient. The distance between the axis of the strips must always be 300 mm. VERTICAL STRIP 400 mm 300 mm ProdEX PANEL FIXED WITH 2 GUIDE STRIPS ProdEX PANEL WITH CONCEALED FIXING (glued) HANGING HOOK The thicknesses to be used for the glue system on façades are 8, 10 and 12 mm. Fastening with glue is a delicate process during which it is essential follow a strict and adequate process, always in line with the adhesive manufacturer's instructions. THICKNESS (mm) DISTANCE BETWEEN FASTENINGS (mm) THICKNESS (mm) DISTANCE BETWEEN FASTENINGS (mm) Each piece must have at least 3 support points in each direction Each piece must have at least 3 support points in each direction. For further information on accessories, see chapter 6 of this catalogue. For further information on accessories, see chapter 6 of this catalogue.

20 B. Instructions for the gluing procedure 1 Clean the ProdEX panel in the adhesion area prior to gluing using a brush, air or a special liquid from the same manufacturer as that of the adhesive. 6 Apply a line of monocomponent glue to the strip that is to be used as the intermediate support (B) of the ProdEX panel alongside the double-sided tape and two lines to the sides of the same tape on the intermediate strips (A). The adhesive must be applied using a manual or pneumatic pistol fitted with a special nozzle that applies a triangular cross-section. Always check that the adhesion surfaces are not wet or dirty. A. 2 Sand the strip on the surface that will be supporting the panel. The wood and aluminum strips must be sanded and it must be ensured that the strip is free of dust and that the gluing area is completely dry. Steel strips must not be sanded in order not to damage the oxide protection they have and must be cleaned of grease using a liquid. 7 Remove the protective tape from the adhesive tape. 3 Shake the primer well before use and apply it to the clean and dry adhesion areas of the panels and strips, bearing in mind not to apply primer to an area greater than what can be glued within the following 6 hours. The specific primer must be used for each material (wood strip, metal strip, panel, etc.) as defined by the manufacturer of the adhesive. 4 Follow the minimum and maximum drying time instructions for the primer according to the material it has been applied to. After this drying time continue with the gluing procedure. 8 After 10 minutes from the application of the adhesive, carefully place the panels, taking care not to press too hard as this will extend the adhesive too much and the façade will become uneven. With the assistance of the double sided adhesive tape, the panels will be held in place in the position required on the strip. 5 On the strips to be used as the intermediate support of the panels (B), place double-sided tape in a continual and parallel manner along the strip and to the side. In the case of strips that will be used as a join between two panels (A), two lengths will have to be placed in the center. Do not remove the protective paper from the surface of the tape yet. B. A. 9 It is mandatory to fasten the panels with the assistance of several clamps (held in place by screws into the strips), until the adhesive polymerizes. These clamps must be placed at intervals of mm (and on all the corners) without exerting pressure beyond that of the thickness of the double-sided tape to avoid forcing the panel into an incorrect position THIS GLUING PROCEDURE BY PRODEMA IS A BRIEF AND NON-SPECIFIC INDICATION WHICH IN NO WAY REPLACES THE COMPLETE INSTRUCTIONS OF THE ADHESIVE MANUFACTURER, WHICH EXPLAINS EACH CASE IN DETAIL.

21 3 2 5 FIXED LOUVERS STYLE FASTENING PREPARATION OF THE SUBSTRUCTURE This construction kit permits the installation of ProdEX panel slats with a thickness of 10 mm in a fixed louvers style. The versatility of the kit permits the installation of these slats in both a horizontal and vertical direction with inclinations of 0, 30 and 60. Installation of the struts to the building The first step in the installation consists of installing the special strips upon which the louvers are to be installed. In order to carry out the installation of these strips to the building, L-shaped aluminum brackets are used. The struts are fastened to these brackets using a T-M28 25 mm long bolt, the head of which fits perfectly into the laterals of the strut and is tightened using a DIN 125 A washer and a DIN 943 nut. Depending on the distance to be left between each of the fixed louvers and the building, a different model of L-shaped bracket is selected, as the louvers are supplied in varying lengths. BOLT HOUSING SIMPLE FASTENING SIMPLE BRACKET VARIABLE LENGTH (see accessories) To carry out this installation, Prodema supplies 10 mm thick slats of ProdEX panels in 3 different widths. These slats can be supplied with the selected finish on one side or both. FASTENING OF DOUBLE BRACKET BETWEEN STRUTS DISTANCE BETWEEN BRACKETS 2440 mm STRUT FOR FIXED LOUVERS 114 mm T-M8 BOLT 1 m 94 mm DIN 125 A stainless steel WASHER DOUBLE BRACKET (Variable length) DIN 943 stainless steel NUT 1 m 86 mm The installation of this constructive kit is carried out in three easy steps: preparation of the substructure, preparation of the ProdEX slats and the installation of the fixed louvers.

22 Depending on the type of louver to be installed (vertical or horizontal), the position in which the struts need to be installed varies: vertically for horizontal fastened louvers and horizontally for vertical fastened louvers. INSTALLATION OF STRUTS FOR HORIZONTAL FASTENED LOUVERS INSTALLATION OF STRUTS FOR VERTICAL FASTENED LOUVERS PREPARATION OF ProdEX SLATS The support pieces that will be used to anchor the louvers to the substructure will be fitted to the rear side of the ProdEX pieces supplied by Prodema. Every ProdEX louver must have three supports fitted to its rear, two on the edges (a maximum of 40 mm from the edge) and the third in the geometric center of the piece. In order to prevent any lateral or vertical movement (depending on the position) of the slats, a support with a tab must be fitted in the center of the piece. Two 9.5mm longtb-a2 TX 30 screws will be used to fasten the supports to the ProdEX slats. To do so, a pre-drilled knock-out hole of mm must be made in the panel, taking care to leave 2 mm of material between the bottom of the hole and the good face of the louver. It is very important that these struts are in perfect alignment at all times, given that any error made in the vertical alignment and/or alignment of these struts will result in imperfections being transferred to the louvers. Additionally, it is very important to know that the installation of the fixed louvers must allow for ventilation between the panels and the enclosure. SLAT SUPPORT TB-A2 TX 30 SCREW Installation of the supports for the struts Once the special struts have been fitted for the installation of the Prodema fixed louvers, it is necessary to attach the supports to which the louvers will be anchored. The anchoring of these pieces to the struts will be performed using two austenitic stainless steel self-threading screws (one on each side). It is important to point out that the struts are supplied with already machined holes to indicate the gap (distance) of 20 mm between louvers. Although this gap is standard, the struts can be supplied without any type of perforation for special jobs. Furthermore, these struts and accessories can also be supplied anodized, lacquered in any color from the RAL chart or FUTURA chart (see accessories section). maximum distance border - axis: 40 mm TB-A2 TX 30 SCREW center SLAT SUPPORT INSTALLATION OF THE ANCHOR PIECE 20 mm SLAT SUPPORT WITH TAB SELF-THREADING SCREW DIN x 13 stainless steel For further information on accessories, see chapter 6 of this catalogue. Each slat must have three supports, regardless of length.

23 INSTALLATION OF FIXED LOUVERS EXPANSION JOINTS Once the louvers and the substructure are ready, all that needs to be done is to fit the pieces until a 'clack' is heard and the installation will be complete. This step is very easy and quick, simplifying the installation and reducing the time required for it. INSTALLATION OF FIXED LOUVERS PARALLEL TO FAÇADE (0º) When installing a fixed continuous louver, there must be a 6 mm expansion joint between each of the pieces. VIEW OF EXPANSION JOINT 6 mm SUPPORTS ON THE BORDERS OF EACH SLAT To do this, the base piece necessary is wider, in order to accommodate the two slats on a single base piece. There is a double base piece of each available inclination 0º, 30º and 60º. INSTALLATION OF THE DOUBLE BASE PIECE BASE PIECE FOR STRAIGHT FIXED LOUVERS (0º) INSTALLATION OF INCLINED FIXED LOUVERS PARALLEL TO FAÇADE (30º AND 60º) BASE PIECE FOR INCLINED FIXED LOUVERS (30º) INSTALLATION OF TWO CONTINUOUS LOUVERS DOUBLE BASE PIECE FOR STRAIGHT FIXED LOUVERS (0º) BASE PIECE FOR INCLINED FIXED LOUVERS (60º)* DOUBLE BASE PIECE FOR INCLINED FIXED LOUVERS (30º) * See warranty conditions on page 9. DOUBLE BASE PIECE FOR INCLINED FIXED LOUVERS (60º)*

24 3 2 6 CLAPBOARD FAÇADE STYLE FASTENING INSTALLATION OF ProdEX SLATS This system permits the installation of ProdEX 8mm pieces of panel in an overlapping fashion using a hidden fastening system. The installation of the slats must be carried as detailed below INSTALLATION OF THE SUBSTRUCTURE First of all, start by using a standard wood or metal substructures, the same as for the visible fastening system. To do so, follow the instructions in points and of this technical catalogue. Step 1 First, install the pieces that will support the panels. These pieces, manufactured in stainless steel and lacquered in black, are supplied by Prodema. The installation of these pieces is carried out by fastening them with a screw to the strip starting at the lower section of the façade and taking into account that it is very important that the pieces are properly aligned as the panels are going to rest on these pieces. It is recommended to insert a peg (a wooden one for example) at the rear of this first piece to serve as a stopper. METAL SUBSTRUCTURE WOOD SUBSTRUCTURE Different screws can be used: FOR METAL STRIPS: DIN 7504 N (black zinc plating) FOR WOOD STRIPS:DIN 7505 B (black zinc plating) 3,9 mm 3,9 mm 19 mm 25 mm Aluminum substructure: stainless steel screw. Steel substructure: galvanized steel screw. Step 2 For slats measuring 2440 mm, the strips must be 60 mm wide and be separated by approximately 600 mm between centers. 600 mm 600 mm 600 mm 600 mm 60 mm Once the first line of pieces has been installed, this is when the first piece of ProdEX is installed. In this case, this is ProdEX material with a thickness of 8 mm and is supplied in two different widths: 190 and 290 mm (it is supplied in 2440 mm lengths, which can later be adjusted on site). These pieces have been machined so that they insert perfectly into the already installed steel pieces, with the panel being fastened at the bottom. Prodema will supply the slats cut and machined in the sizes detailed below: ANCHOR PIECE FOR SLAT (see step 1). 190, 290 mm (standard size) 46 It is very important 47 that all the pieces are 2440 mm aligned. (standard size) The substructure must ensure that each piece has at least 3 support points. SLATS MACHINED FOR AMERICAN FAÇADE VIEW OF MACHINING ON SLAT

25 Step 3 The third step consists of anchoring the ProdEX pieces at the top. To do this, the same piece of stainless steel will always be used. One the first piece has been anchored, simply repeat these three steps again and again to continue installing the panels on the façade. 3 3 UNIQUE FAÇADES UNIQUE SHAPES The ProdEX material offers so much versatility to create different types of façades that it is possible for it to be machined into an infinite number of shapes. To carry out this type of machining, it is very important to follow the instructions in section 2.3 of this catalog or contact Prodema (prodema@prodema.com). Step 4 As with the other installation systems available for ProdEX, in the case of the America façade, it is necessary to leave an expansion joint of 6 8 mm between pieces. This joint is performed by using only one anchor piece, as this piece is sufficiently wide to fasten two pieces at the same time as well as leave a joint of 6 8mm. In this VIEW OF EXPANSION JOINT manner, it ensures the flatness of both pieces of ProdEX, thereby preventing any raised areas on either of the two or preventing them from being on different levels. The part that is exposed through the joint cannot be seen as the anchor piece is supplied in matte black lacquer. 6-8 mm Step 5 To finish, the panels at the uppermost part are fastened in place using standard Prodema screws. In order to select the most appropriate according to the type of strip, the material of the substructure must be taken into consideration. Metal: screw type SX3 - L x 32 Wood: screw type TW - S - D x 38 (see accessories section). THREE INSTALLATION PATTERNS Due to the versatility of the system, it is possible to install it using different patterns without the need to vary the position of the strips or the anchor pieces; provided that the offset of the pieces is a multiple of 600 mm OFFSET MULTIPLE OF 600 mm

26 Recommendations for machining the ProdEX panel There are a series of limitations and requirements to consider when carrying out any type of machining on ProdEX panels for their use on exteriors. It must be remembered that with every perforation added to the panel, there is a higher number of borders on the panel, which means that there are more edges exposed to the sun and water, and this could result in some form of aesthetic problem with the panel. For this reason consider the following recommendations: 1. The machining must be performed by a professional using the appropriate tools. 2. If the percentage of perforations is elevated (>20%), it is advisable to contact Prodema. 3. Regardless of the machining performed on the panel, a perimeter of 75mm must be left around the panel / piece without being machined. Cracks due to stress Due to the requirements to perforate the ProdEX panels, whether due to aesthetic or functional reasons (ventilation outlets, installation of signage, lighting, etc.) it is very important that certain recommendations are considered to avoid any cracking to the panel due to the accumulation of stress. HOLLOWING, GROOVES, ETC.: In the event of performing any hollowing, grooves or machining of this type, it is very important to avoid leaving any sharp edges at all times, always leaving the largest radius possible in each case, the minimum radius being 5 mm. 4. The minimum distance to leave between machining must never be less than 75 mm. 5. In the case that the machining carried out is in the form of perforations, the maximum diameter of each may not be greater than 150 mm. 6. The maximum machined percentage must not exceed 30%. In any event, whenever machining is to be performed on the panel, the express consent of the Prodema Technical Department must be obtained. GROOVES ON THE EDGE: Min. 75 mm It is likely that on some occasions, and always with the approval of the Prodema Technical Department, machining will be required to add a groove on the edge of the ProdEX panels (for an American style façade installation for example). In these cases, it is also very important to avoid sharp edges and attempt to maximize their size, with the recommended minimum being 1 mm. Min. 75 mm 1220 Ø Max. 150 mm 2440 Min. 75 mm 50 51

27 3 3 2 SUSPENDED CEILINGS HIDDEN FASTENING WITH CAPS The versatility of the ProdEX construction kits permits their installation as suspended ceilings. To do so, select the installation system that is most suited to each project and take into consideration some brief recommendations. This system permits the installation of ProdEX panels of a thickness of mm as a suspended ceiling, using caps to hide the heads of the fastening screws VISIBLE FASTENING In order to install ProdEX panels as a suspended ceiling, it is very important to take into account the instructions detailed in section of this technical catalogue. In addition to this, it is also very important to take into account that the strips that serve as the support for the panels are installed perpendicular to the grain of the panels. L60 / L100 BRACKET L STRUT T STRUT SCREW To perform this kind of installation, it is essential to follow the steps indicated in points and of this technical catalogue. In addition to this, it is also essential to take into account that the strips that serve as the support for the panels are installed perpendicular to the grain of the panels and respecting the distances detailed in the following table: The minimum thickness of the ProdEX panels to be used for a suspended ceiling is 8 mm and the maximum 14 mm. The distance between fastenings must be performed in accordance with the following table: THICKNESS (mm) DISTANCE BETWEEN STRIPS (mm) Each piece must have at least 3 support points in each direction HIDDEN FASTENING WITH HANGING STRUT THICKNESS (mm) DISTANCE BETWEEN STRIPS (mm) 8, Each piece must have at least 3 support points in each direction. Never use countersunk screws for fastening ProdEX. Another hidden fastening system for the installation of ProdEX panels as a suspended ceiling is hanging struts. To do so, it is necessary follow the instructions in section of this technical catalogue without exception. L60 / L100 BRACKET L STRUT Perimeter ventilation 2 1 GUIDE STRIP On all suspended ceiling installations there must be a perimeter space of at least 20 mm 1 ProdEX PANEL to allow for the ventilation of the panels and therefore avoid having any differences in 1 52 temperature and humidity on both sides of the panels. 53 * Rivets are only used with metal substructures, not wood substructures. For further information on accessories, see chapter 6 of this catalogue.

28 b Fastening panels 1. Simultaneously fit all the anchor pieces onto the rear of the panel to the structure by pressing upwards from below. 2. Move the piece until it is fitted to the guide strips. 3. Once each piece has been fitted and when they have been aligned and in their definitive position, it is essential that they be fixed in place. For this purpose is recommended to use an austenitic stainless steel self-threading screw, inserting it into the central upper clip and fastening it to the horizontal hanging strut. The recommended thickness of the ProdEX panels for this use are 10, 12 and 14 mm and the distance between the fastening clips shall be as detailed in the following table: THICKNESS (mm) DISTANCE BETWEEN FASTENINGS (mm) Each piece must have at least 3 support points in each direction HANGING CLIP LEVELING SCREW ProdEX PANEL 10 mm 1 GUIDE STRIP FASTENING SCREW a The color, shape, etc., of the frame can be modified depending on the project. It is recommended to contact Prodema (prodema@prodema.com). Depending on the requirements of each project, the louver can be moved either manually or with a motor, synchronized or individually and activated by an infinity of systems, such as automation centers, remote controls, sensors, etc. This chassis is supplied completed and made to measure, together with all the accessories for its installation on the project. a: In order to obtain a louver of one single piece, the maximum length must be 2440 mm. Greater lengths can be considered, but require the use of more than one piece of ProdEX panel. b: Maximum 600 mm MOVABLES LOUVERS In addition to the fixed louver construction kit, Prodema has also developed a complete turnkey system for vertical movable louvers. This system of movable louvers is studied on a project by project basis given that the design is carried out to adapt the size of each louver and its motorization to the requirements of each project CURVES CURVES USING STRAIGHT PANELS: POLYGONAL CURVE The curving technique consists of using straight panels to create curved surfaces. Depending on the installation system selected, it is necessary to follow the specific instructions for that system previously detailed in this technical catalogue. To create each louver, Prodema designs an aluminum chassis to which the ProdEX panels are fitted to the sides using the most suitable visible or hidden system depending on the requirements of each project. The thicknesses of the panels used can vary with 6 mm being the minimum

29 CURVES USING STRAIGHT PANELS: CURVING PANELS Panel thickness ProdEX is sufficiently flexible that it can be molded to a curved substructure and remain in the desired position. In order for the material to perfectly mold to the radius of curvature and so that the stresses of the panel are irrelevant for the façade once finalized, there follows a table of some factors to take into consideration during installation: The thickness of the panel is selected according to the following table: RADIUS OF CURVATURE REQUIRED ON PROJECT 5,00 m - 10,00 m USE ProdEX PANELS WITH A THICKNESS OF 6 mm DISTANCE BETWEEN STRIPS 300 mm 10,00 m - 20,00 m > 20,00 m 8 mm 10 mm 400 mm 450 mm This table indicates the minimum radii of curvature for a panel measuring 2440 x 1220 mm. If when using a single length of panel the width is reduced, the material permits more closed radii to be obtained. Fastening distances of the material between vertical supports It is very important to take into account that the ProdEX panels fastened to curved area must be fastened to and supported by more strip than the substructure recommended for non-curved façades (see table on this page) PRECURVED ProdEX The precurved panels are ProdEX panels that are supplied already curved in different radii. Depending on the direction of the grain selected, the formats of the panels are different. The panels for curved façades are only fastened using the visible fastening system using screws or rivets and are curved only in the direction of the grain. Direction of the grain 56 57

30 1. INSPECTION Precurved ProdEX Prodema NATURAL WOOD BEAUTY TECHNICAL DATA SHEET Selection of panels Before proceeding with the installation of the panels, it is very important to know that it is necessary to select the model that best adapts to the requirements of the project. This selection must be carried out as indicated below: 1) Selection of the precurved ProdEX panel: these panels are offered in a variety of formats, depending on the direction of the grain selected, the radius of curvature of the area where the panel is to be installed, and whether a concave or convex curve is required, as shown in the images below: R 2. DIMENSIONS R PHYSICAL PROPERTIES 595 Sale format depending on the direction of the grain. Available Radiuses: 354, 500, 1000, 2000 and 4000 mm The precurved panels are offered in concave and convex format 4. RESISTANCE TO WEATHER 2) Selection of the radii of curvature: when selecting the radius of curvature of the precurved panel, first it is necessary to consider the radius of curvature of the area where the panel is to be installed. The radius of curvature of the area where the panel is to be installed does not always have to match that of the standard radii offered, therefore, in these cases the manner in which to proceed is as follows: a. Consider the radius of curvature of the building. 5. SAFETY REQUIREMENTS b. Always use a standard panel radius, this being the one closest to the radius of curvature of the building but always greater than said radius. Examples: Building radius 3,700 mm Precurved panel radius 4,000 mm Building radius 1,400 mm Precurved panel radius 2,000 mm NOTE: In cases where the radius of the building is very similar to that of the panel, 1 CWFT CWFT (Classified Without Further Testing): in accordance with EN Sect Screw or rivet e.g mm; the closest radius of curvature is selected, in other words, 1000 mm. 58 based installation recommended. For other fastening systems consult the Prodema Technical Dept Format subject to minimum quantities; contac Prodema.

31 Installation systems Once the appropriate panel has been selected that adapts to the requirements of the project, installation can begin. It is very important to know that this type of ProdEX panel can only be installed using a mechanical through fasteners, in other words, screws and rivets, as described in section of this technical catalogue. Given that in the majority of cases the radius of curvature of the panel will be slightly higher than the radius of curvature of the building, it is necessary that each piece is installed on three strips, as indicated below: Minimum fastenings per piece and types of precurved corner panels Depending on the type of precurved ProdEX panel to be installed, the minimum number of fastenings per piece varies. For this reason, below follows the required number of fastenings per precurved ProdEX model according to the type of curve, in other words, depending on whether the pieces are concave or convex. In turn, each model is assigned a different letter to facilitate identification. CONVEX PIECES In this case, the central strip is only used as support, with the screws or rivets being fastened only on the lateral strips of each piece: Max. 600 mm Max. 600 mm TYPE A Piece measuring 595 x 1220 mm 6 through fasteners TYPE B Piece measuring 2440 x 595 mm 10 through fasteners CONCAVE PIECES Max. 600 mm When installing convex pieces, fasteners must be included on the central strip L STRIP to adjust each piece to the required radius, as detailed below: Max. 600 mm BRACKET 2 T STRIP TYPE C Piece measuring 595 x 1220 mm 9 through fasteners TYPE D Piece measuring 2440 x 595 mm 15 through fasteners PRECURVED ProdEX CORNER 2 SCREW The precurved ProdEX corner panels and ProdEX panels that are supplied have already been curved at 90º for corner cladding. Depending on the direction of the grain selected, the formats of the panels are different. 1. Support the central axis of the piece on the central support strip. 2. Fix the sides of the piece using screws or rivets

32 Precurved ProdEX Corner Selection of panels Prodema NATURAL WOOD BEAUTY TECHNICAL DATA SHEET In order to select these panels and therefore adapt them to the requirements of each project, it is necessary to consider the direction of the grain as well as whether it is to clad a convex or concave corner. The options offered by the precurved ProdEX panels are detailed below: 1. INSPECTION 2. DIMENSIONS Sale format depending on the direction of the grain. = 90º The precurved panels are offered in convex and concave format PHYSICAL PROPERTIES Installation systems Once the appropriate panel has been selected that adapts to the requirements of the project, installation can begin. It is very important to know that this type of ProdEX panel can only be installed using a mechanical through fasteners, in other words, screws and rivets, as described in section of this technical catalogue. The installation of these panels, depending on the type of curvature, must be carried out in the following manner: 4. RESISTANCE TO WEATHER CONVEX PIECES 5. SAFETY REQUIREMENTS SUBSTRUCTURE FASTENING SCREW AIR CHAMBER 62 1 CWFT (Classified Without Further Testing): in accordance with EN Sect Screw or rivet based ProdEX PANEL 63 installation recommended. For other fastening systems consult the Prodema Technical Dept. PRECURVEDCORNER 2 Format subject to minimum quantities; contact Prodema.

33 CONCAVE PIECES Role of the pieces SUBSTRUCTURE AIR CHAMBER FASTENING SCREW 1 Firstly, it is very important to determine the role of each piece of ProdEX so that they may later fit perfectly in the place where they are to be fastened. In the case of the sphere, the role of each piece will be that displayed alongside this text. When performing any machining of the different parts, the instructions detailed in section 2.4 of this technical catalogue must be followed. ProdEX PANEL PRECURVED CORNER 1. Press the central axis inwards. 2. Fix the sides of the piece using screws or rivets. Minimum fastenings per piece and types of precurved corner panels The minimum amounts of screws / rivets per piece depend mainly on the dimensions of each one, as specified below: TYPE E TYPE F Curved combinations Once all the pieces have been machined, they can be installed on a substructure that complies with the requirements necessary for the ProdEX panels, as detailed in section of this technical catalogue. In this particular case and in order to obtain the sphere shape, it is necessary to determine the radius of curvature of each piece in the direction of the grain, as this is what will determine the thickness of the panels. To do so, it is necessary to follow the instructions in section and follow them without exception. Whereas, the pieces do not curve in the direction perpendicular to the grain, although despite their reduced width, the curve is obtained in a polygonal shape as detailed in section of this catalogue. Max. 600 mm. Max. 600 mm. TYPE G TYPE H This example aims to highlight that by combining the different cutting techniques and ProdEX curved pieces and panels detailed in this technical catalogue, it is possible to achieve unique shapes and appearances that adapt to each particular project. 3 4 INSTALLATION DETAILS Pieces measuring 2440 x 595 mm 10 through fasteners Pieces measuring 595 x 1220 mm 6 through fasteners Prodema has an extensive range of solutions showing all types of installation details to address corners, windows, crowns, etc SPECIAL CURVED PIECES Taking into account the indications contained in this catalogue, complex forms can be obtained following simple operations. 64 Below, and by means of example, is the manner in which to create a sphere using ProdEX panels with visible fastenings. 65 All of these details are available on the Prodema website (

34 4 POST-INSTALLATION It is recommended to perform a cleaning test on a small area of the material for the purpose of verifying the efficacy of the procedure, and only then proceed with the remainder of the surface. There is no method for repairing scratched or dented panels. 4 1 REMOVING THE PROTECTIVE SURFACE The ProdEX panels are protected by a special film on the visible side. This protective film applied in the factory must be removed from the panel surface as soon as the product has been installed. Never try to remove the film from the reverse side as this is not a protective film and is necessary for the stability of the panel. 4 3 The use of solvents or chemical cleaning products must always be done according to the corresponding health and safety rules. MAINTENANCE ProdEX panels do not require maintenance. In the case of dirt, refer to the Cleaning section. Never leave an installed panel, or one exposed to the elements, with its exterior protective film in place for more than 2 3 hours. This will prevent the film from adhering too much to the panel and avoid having to remove it using special products and/or prevent the panel from warping. 4 4 REPAIR Natural wood is a delicate material. There is no prescribed repair method for ProdEX panels. Damaged panels must be replaced with new ones. 4 2 CLEANING It is difficult for dirt to adhere to the ProdEX panel surface. 5 REMOVAL INFORMATION However, if the surface becomes dirty or there are remains of the protective film adhesive, this can be cleaned with lukewarm water mixed with a liquid detergent using a soft cloth. Do not rub the surface when dry. Never use abrasive detergents. 5 1 REMOVAL The ProdEX product forms part of a ventilated façade construction kit, the main components of which (aluminum, steel, wood and plastic) are easily separable and recyclable. In the case of more resistant grime, the panel surface may also be cleaned with a soft cloth (un-dyed) dampened with benzene-free petroleum ether (40 60ºC, light naphtha). 5 2 WASTE MANAGEMENT Reuse: reuse of the ProdEX panel for other applications with different requirements is desirable. Never use cloths or sponges with abrasive cleaning or sanding products, as this may damage the surface of the product. Recycling: the cellulose fibers of the core and the thermostable wooden sheet can be recycled. Recycling possibilities include its use a filler material for wood-based panels for construction use. Nor should aggressive solvents such as acetone, ethyl acetate, MEC, nail polish, etc., be used, as these may cause permanent damage by partially or completely dissolving the protective film surface or cause cracks, which may not be evident at first glance. These products must not be used on the reverse face of the panels either. Dumping at landfill sites: the specifications that regulate and manage construction and demolition waste shall be followed, as well as any applicable local regulations. Disposal in industrial incinerators can also be considered. Sub-construction: the wooden, aluminum or steel profiles may be directly reused for their original use, or recycled if the buildings have been carefully deconstructed. Surface drying is best performed using an absorbent, 66 lint-free cloth. 67 FOR FURTHER INFORMATION, CONTACT PRODEMA (prodema@prodema.com).

35 6 ACCESSORIES GALVANIZED STEEL REFERENCE DESCRIPTION MATERIAL / FINISH 6 1 GENERAL ELEMENTS FOR THE PRIMARY SUBSTRUCTURE ALUMINUM: PRSS001GLV 30 mm Omega strut 2500 mm bar Galvanized steel REFERENCE DESCRIPTION MATERIAL / FINISH PRSS002GLV L 60/50 strut 2500 mm bar Galvanized steel PRAS001BRU T Strut 60/ mm bar Aluminum 6063 / Rough T5 PRSS003GLV L 60 Bracket Galvanized steel PRAS002BRU T Strut 60/ mm bar Aluminum 6063 / Rough T5 PRAS003BRU L 60 Bracket Aluminum 6060 / Rough T5 PRSS004GLV L 100 Bracket Galvanized steel PRAS004BRU L 100 Bracket Aluminum 6060 / Rough T5 6 2 SPECIFIC ELEMENTS FOR THE VISIBLE FASTENING SYSTEM WITH SCREWS OR RIVETS SCREWS PRAS005BRU (only sold in the USA) Modified Z strut 146" (3708 mm) bar Aluminum / Rough GENERAL ACCESSORIES FOR SCREWS REFERENCE DESCRIPTION MATERIAL / FINISH PRAS005AND (only sold in the USA) PRAS006BRU (only sold in the USA) Modified Z strut 146" (3708 mm) bar Inverted HAT strut 146" (3708 mm) bar Aluminum / Anodized black Aluminum / Rough PRGA001EXF SFS-SX Centering seat Accessory to ensure the perpendicularity of the screw to the panel, as well as its concentric insertion. PRAS006AND (only sold in the USA) Inverted HAT strut 146" (3708 mm) bar Aluminum / Anodized black PRGA002EXF SFS-T20W Adapter Accessory for SX3 and/or TW-S screws with TORX heads PRGA003EXF SFS-E 420 Setting tool Accessory for SX3 screws 68 - Federvision with IRIUS heads 69 To determine delivery times, minimum quantities, etc., contact Prodema (prodema@prodema.com). To determine delivery times, minimum quantities, etc., contact Prodema (prodema@prodema.com).

36 SPECIFIC SCREWS FOR ALUMINUM AND/OR STEEL SUBSTRUCTURE REFERENCE DESCRIPTION MATERIAL / FINISH REFERENCE DESCRIPTION MATERIAL / FINISH PREF001IRI SFS-SX3-L12-5,5x32 mm Self-drilling screw IRIUS head Thickness of assembly 17mm Ø screw: 5,5 mm L: 32 mm Unlacquered PREF004IRI SFS-SX3-L12-5,5x32 mm Self-drilling screw IRIUS head Thickness of assembly 17mm Ø screw: 5,5 mm L: 32 mm PALE lacquer PREF001TRX SFS-SX3-L12-5,5x32 mm Self-drilling screw TORX head Thickness of assembly 17mm Ø screw: 5,5 mm L: 32 mm Unlacquered PREF004TRX SFS-SX3-L12-5,5x32 mm Self-drilling screw TORX head Thickness of assembly 17mm Ø screw: 5,5 mm L: 32 mm PALE lacquer PREF002IRS SFS-SX3-L12-5,5x32 mm Self-drilling screw IRIUS head Thickness of assembly 17mm Ø screw: 5,5 mm L: 32 mm CREAM lacquer PREF005IRS SFS-SX3-L12-5,5x32 mm Self-drilling screw IRIUS head Thickness of assembly 17mm Ø screw: 5,5 mm L: 32 mm RUSTIK lacquer PREF002TRX SFS-SX3-L12-5,5x32 mm Self-drilling screw TORX head Thickness of assembly 17mm Ø screw: 5,5 mm L: 32 mm CREAM lacquer PREF005TRX SFS-SX3-L12-5,5x32 mm Self-drilling screw TORX head Thickness of assembly 17mm Ø screw: 5,5 mm L: 32 mm RUSTIK lacquerk PREF003IRS SFS-SX3-L12-5,5x32 mm Self-drilling screw IRIUS head Thickness of assembly 17mm Ø screw: 5,5 mm L: 32 mm ICE GREY lacquer PREF006IRS SFS-SX3-L12-5,5x32 mm Self-drilling screw IRIUS head Thickness of assembly 17mm Ø screw: 5,5 mm L: 32 mm LIGHT BROWN lacquer SFS-SX3-L12-5,5x32 mm SFS-SX3-L12-5,5x32 mm Self-drilling screw Self-drilling screw TORX head Thickness of assembly 17mm PREF006TRX TORX head PREF003TRX Thickness of assembly 17mm 70 ICE GREY lacquer LIGHT BROWN lacquer 71 Ø screw: 5,5 mm L: 32 mm Ø screw: 5,5 mm L: 32 mm * Self-drilling fastening are recommended for 2.5mm thick aluminum profiles or for 1.5mm thick steel profiles. For lesser thicknesses, rivets should be used. To determine delivery times, minimum quantities, etc., contact Prodema (prodema@prodema.com).

37 REFERENCE DESCRIPTION MATERIAL / FINISH REFERENCE DESCRIPTION MATERIAL / FINISH PREF007IRI SFS-SX3-L12-5,5x32 mm Self-drilling screw IRIUS head Thickness of assembly 17mm Ø screw: 5,5 mm L: 32 mm MINT lacquer PREF010IRI SFS-SX3-L12-5,5x32 mm Self-drilling screw IRIUS head Thickness of assembly 17mm Ø screw: 5,5 mm L: 32 mm NUX lacquer PREF007TRX SFS-SX3-L12-5,5x32 mm Self-drilling screw TORX head Thickness of assembly 17mm Ø screw: 5,5 mm L: 32 mm MINT lacquer PREF010TRX SFS-SX3-L12-5,5x32 mm Self-drilling screw TORX head Thickness of assembly 17mm Ø screw: 5,5 mm L: 32 mm NUX lacquer PREF008IRS SFS-SX3-L12-5,5x32 mm Self-drilling screw IRIUS head Thickness of assembly 17mm Ø screw: 5,5 mm L: 32 mm DEEP BROWN lacquer PREF011IRS SFS-SX3-L12-5,5x32 mm Self-drilling screw IRIUS head Thickness of assembly 17mm Ø screw: 5,5 mm L: 32 mm MOCCA lacquer PREF008TRX SFS-SX3-L12-5,5x32 mm Self-drilling screw TORX head Thickness of assembly 17mm Ø screw: 5,5 mm L: 32 mm DEEP BROWN lacquer PREF011TRX SFS-SX3-L12-5,5x32 mm Self-drilling screw TORX head Thickness of assembly 17mm Ø screw: 5,5 mm L: 32 mm MOCCA lacquer PREF009IRS SFS-SX3-L12-5,5x32 mm Self-drilling screw IRIUS head Thickness of assembly 17mm Ø screw: 5,5 mm L: 32 mm SFS-SX3-L12-5,5x32 mm Self-drilling screw TORX head Thickness of assembly 17mm DARK BROWN lacquer PREF012TRX SPECIFIC SCREWS FOR WOOD SUBSTRUCTURE SFS-TW-S-D12-4,8x38 mm screw TORX head Dimensiones: Ø screw: 4,8 mm L: 38 mm unlacquered PREF009TRX 72 DARK BROWN lacquer Ø screw: 5,5 mm 73 L: 32 mm REFERENCE DESCRIPTION MATERIAL / FINISH To determine delivery times, minimum quantities, etc., contact Prodema (prodema@prodema.com). To determine delivery times, minimum quantities, etc., contact Prodema (prodema@prodema.com).

38 REFERENCE DESCRIPTION MATERIAL / FINISH REFERENCE DESCRIPTION MATERIAL / FINISH PREF013TRX SFS-TW-S-D12-4,8x38 mm screw TORX head Ø screw: 4,8 mm L: 38 mm CREAM lacquer PREF019TRX SFS-TW-S-D12-4,8x38 mm screw TORX head Ø screw: 4,8 mm L: 38 mm DEEP BROWN lacquer PREF014TRX SFS-TW-S-D12-4,8x38 mm screw TORX head Ø screw: 4,8 mm L: 38 mm ICE GREY lacquer PREF020TRX SFS-TW-S-D12-4,8x38 mm screw TORX head Ø screw: 4,8 mm L: 38 mm DARK BROWN lacquer PREF015TRX SFS-TW-S-D12-4,8x38 mm screw TORX head Ø screw: 4,8 mm L: 38 mm PALE lacquer PREF021TRX SFS-TW-S-D12-4,8x38 mm screw TORX head Ø screw: 4,8 mm L: 38 mm NUX lacquer PREF016TRX SFS-TW-S-D12-4,8x38 mm screw TORX head Ø screw: 4,8 mm L: 38 mm RUSTIK lacquer PREF022TRX SFS-TW-S-D12-4,8x38 mm screw TORX head Ø screw: 4,8 mm L: 38 mm MOCCA lacquer PREF017TRX SFS-TW-S-D12-4,8x38 mm screw TORX head Ø screw: 4,8 mm L: 38 mm LIGHT BROWN lacquer RIVETS GENERAL ACCESSORIES FOR RIVETS REFERENCE DESCRIPTION MATERIAL / FINISH PRGA004EXF SFS-ZL Centering seat Accessory to perform the pre-drilling of the substructure concentrically to that of the wall SFS-TW-S-D12-4,8x38 mm screw TORX head PREF018TRX Recommended accessory MINT lacquer Ø screw: 4,8 mm PRGA005EXF SFS Centering seat to perform the pre-drilling L: 38 mm with integrated bit of the substructure concentrically to that of the 74 panel. 75 To determine delivery times, minimum quantities, etc., contact Prodema (prodema@prodema.com). To determine delivery times, minimum quantities, etc., contact Prodema (prodema@prodema.com).

39 REFERENCE DESCRIPTION MATERIAL / FINISH PRGA006EXF PRGA007EXF SFS-AP nozzle SFS-SSO-D15 nozzle SPECIFIC RIVETS FOR ALUMINUM SUBSTRUCTURE Accessory to be used only with SFS-AP16 rivets. This is fitted to the riveter for the installation of the rivets on floating points Accessory to be used only with SFS-SSO-D15 rivets. This is fitted to the riveter for the installation of the rivets on floating points REFERENCE DESCRIPTION MATERIAL / FINISH SFS-AP rivet Thickness of assembly: 8,0-12,0 mm Ø head: 16 mm PREF023AP016 Ø rivet: 5 mm Body: AlMg 5 Ø head thickness 1,5 mm Shaft: Stainless steel Ø shaft thickness 2,7 mm L: 16 mm Unlacquered L: 18 mm PREF023AP018 Thickness of assembly: 9,5-13,5 mm PREF023AP021 L: 21 mm Thickness of assembly: 12,5-16,5 mm SFS-AP rivet Thickness of assembly: 8,0-12,0 mm Ø head: 16 mm Ø rivet: 5 mm Body: AlMg PREF024AP016 5 Ø head thickness 1,5 mm Shaft: Stainless steel Ø shaft thickness 2,7 mm L: 16 mm CREAM lacquer PREF024AP018 L: 18 mm Thickness of assembly: 9,5-13,5 mm PREF024AP021 L: 21 mm Thickness of assembly: 12,5-16,5 mm SFS-AP rivet Thickness of assembly: 8,0-12,0 mm Ø head: 16 mm Ø rivet: 5 mm Body: AlMg PREF025AP016 5 Ø head thickness 1,5 mm Shaft: Stainless steel Ø shaft thickness 2,7 mm L: 16 mm ICE GREY lacquer PREF025AP018 L: 18 mm Thickness of assembly: 9,5-13,5 mm PREF025AP021 L: 21 mm Thickness of assembly: 12,5-16,5 mm REFERENCE DESCRIPTION MATERIAL / FINISH SFS-AP rivet Thickness of assembly: 8,0-12,0 mm PREF027AP016 PREF027AP018 PREF027AP021 PREF028AP016 PREF028AP018 PREF028AP021 PREF029AP016 PREF029AP018 PREF029AP021 PREF030AP016 PREF030AP018 PREF030AP021 PREF031AP016 Ø head: 16 mm Ø rivet: 5 mm Ø head thickness 1,5 mm Ø shaft thickness 2,7 mm L: 16 mm L: 18 mm Thickness of assembly: 9,5-13,5 mm L: 21 mm Thickness of assembly: 12,5-16,5 mm SFS-AP rivet Thickness of assembly: 8,0-12,0 mm Ø head: 16 mm Ø rivet: 5 mm Ø head thickness 1,5 mm Ø shaft thickness 2,7 mm L: 16 mm L: 18 mm Thickness of assembly: 9,5-13,5 mm L: 21 mm Thickness of assembly: 12,5-16,5 mm SFS-AP rivet Thickness of assembly: 8,0-12,0 mm Ø head: 16 mm Ø rivet: 5 mm Ø head thickness 1,5 mm Ø shaft thickness 2,7 mm L: 16 mm L: 18 mm Thickness of assembly: 9,5-13,5 mm L: 21 mm Thickness of assembly: 12,5-16,5 mm SFS-AP rivet Thickness of assembly: 8,0-12,0 mm Ø head: 16 mm Ø rivet: 5 mm Ø head thickness 1,5 mm Ø shaft thickness 2,7 mm L: 16 mm L: 18 mm Thickness of assembly: 9,5-13,5 mm L: 21 mm Thickness of assembly: 12,5-16,5 mm SFS-AP rivet Thickness of assembly: 8,0-12,0 mm Ø head: 16 mm Ø rivet: 5 mm Ø head thickness 1,5 mm Ø shaft thickness 2,7 mm L: 16 mm L: 18 mm Thickness of assembly: 9,5-13,5 mm L: 21 mm Thickness of assembly: 12,5-16,5 mm SFS-AP rivet Thickness of assembly: 8,0-12,0 mm Ø head: 16 mm Ø rivet: 5 mm Ø head thickness 1,5 mm Ø shaft thickness 2,7 mm L: 16 mm L: 18 mm Body: AlMg 5 Shaft: Stainless steel RUSTIK lacquer Body: AlMg 5 Shaft: Stainless steel LIGHT BROWN lacquer Body: AlMg 5 Shaft: Stainless steel MINT lacquer Body: AlMg 5 Shaft: Stainless steel DEEP BROWN lacquer Body: AlMg 5 Shaft: Stainless steel DARK BROWN lacquer SFS-AP rivet PREF031AP018 Thickness of assembly: 8,0-12,0 mm PREF031AP021 Ø head: 16 mm Ø rivet: 5 mm Body: AlMg PREF026AP016 5 Ø head thickness 1,5 mm Shaft: Stainless steel Ø shaft thickness 2,7 mm L: 16 mm PALE lacquer Body: AlMg PREF026AP018 L: 18 mm PREF032AP016 5 Thickness of assembly: 9,5-13,5 mm Shaft: Stainless steel L: 21 mm PREF026AP021 Thickness of assembly: 12,5-16,5 mm NUX lacquer 76 PREF032AP018 Thickness of assembly: 9,5-13,5 mm PREF032AP021 L: 21 mm Thickness of assembly: 12,5-16,5 mm 77 To determine delivery times, minimum quantities, etc., contact Prodema (prodema@prodema.com). To determine delivery times, minimum quantities, etc., contact Prodema (prodema@prodema.com).

40 REFERENCE DESCRIPTION MATERIAL / FINISH SFS-AP rivet Thickness of assembly: 8,0-12,0 mm Ø head: 16 mm Body: AlMg PREF033AP016 Ø rivet: 5 mm 5 Ø head thickness 1,5 mm Shaft: Stainless steel Ø shaft thickness 2,7 mm L: 16 mm MOCCA lacquer PREF033AP018 L: 18 mm Thickness of assembly: 9,5-13,5 mm PREF033AP021 L: 21 mm Thickness of assembly: 12,5-16,5 mm REFERENCE DESCRIPTION MATERIAL / FINISH PREF038SS018 SFS-SSO-D rivet Thickness of assembly: 9,0-13,5 mm Ø head: 15 mm Ø rivet: 5 mm Ø shaft thickness: 3,2 mm L: 18 mm Body: Stainless steel A4, nº Shaft: Stainless steel A4, nº RUSTIK lacquer PREF034SS018 PREF035SS018 PREF036SS018 PREF037SS018 SPECIFIC RIVETS FOR STEEL SUBSTRUCTURE REFERENCE DESCRIPTION MATERIAL / FINISH SFS-SSO-D rivet Thickness of assembly: 9,0-13,5 mm Ø head: 15 mm Ø rivet: 5 mm Ø shaft thickness: 3,2 mm L: 18 mm SFS-SSO-D rivet Thickness of assembly: 9,0-13,5 mm Ø head: 15 mm Ø rivet: 5 mm Ø shaft thickness: 3,2 mm L: 18 mm SFS-SSO-D rivet Thickness of assembly: 9,0-13,5 mm Ø head: 15 mm Ø rivet: 5 mm Ø shaft thickness: 3,2 mm L: 18 mm SFS-SSO-D rivet Thickness of assembly: 9,0-13,5 mm Ø head: 15 mm Ø rivet: 5 mm Ø shaft thickness: 3,2 mm L: 18 mm Body: Stainless steel A4, nº Shaft: Stainless steel A4, nº Unlacquered Body: Stainless steel A4, nº Shaft: Stainless steel A4, nº CREAM lacquer Body: Stainless steel A4, nº Shaft: Stainless steel A4, nº ICE GREY lacquer Body: Stainless steel A4, nº Shaft: Stainless steel A4, nº PALE lacquer PREF039SS018 PREF040SS018 PREF041SS018 PREF042SS018 SFS-SSO-D rivet Thickness of assembly: 9,0-13,5 mm Ø head: 15 mm Ø rivet: 5 mm Ø shaft thickness: 3,2 mm L: 18 mm SFS-SSO-D rivet Thickness of assembly: 9,0-13,5 mm Ø head: 15 mm Ø rivet: 5 mm Ø shaft thickness: 3,2 mm L: 18 mm SFS-SSO-D rivet Thickness of assembly: 9,0-13,5 mm Ø head: 15 mm Ø rivet: 5 mm Ø shaft thickness: 3,2 mm L: 18 mm SFS-SSO-D rivet Thickness of assembly: 9,0-13,5 mm Ø head: 15 mm Ø rivet: 5 mm Ø shaft thickness: 3,2 mm L: 18 mm Body: Stainless steel A4, nº Shaft: Stainless steel A4, nº LIGHT BROWN lacquer Body: Stainless steel A4, nº Shaft: Stainless steel A4, nº MINT lacquer Body: Stainless steel A4, nº Shaft: Stainless steel A4, nº DEEP BROWN lacquer Body: Stainless steel A4, nº Shaft: Stainless steel A4, nº DARK BROWN lacquer SFS-SSO-D rivet Thickness of assembly: 9,0-13,5 mm Body: Stainless steel A4, nº PREF043SS018 Ø head: 15 mm Shaft: Stainless steel A4, Ø rivet: 5 mm nº Ø shaft thickness: 3,2 mm NUX lacquer L: 18 mm To determine delivery times, minimum quantities, etc., contact Prodema (prodema@prodema.com). To determine delivery times, minimum quantities, etc., contact Prodema (prodema@prodema.com).

41 REFERENCE DESCRIPTION MATERIAL / FINISH REFERENCE DESCRIPTION MATERIAL / FINISH PREF044SS018 SFS-SSO-D rivet Thickness of assembly: 9,0-13,5 mm Ø head: 15 mm Ø rivet: 5 mm Ø shaft thickness: 3,2 mm L: 18 mm Body: Stainless steel A4, nº Shaft: Stainless steel A4, nº MOCCA lacquer PRCF003CAP Ø 14,25 mm Ø 14,25 2 ProdEX cap Ø 14,25 mm e: 2 mm ProdEX PALE PRCF004CAP 2 ProdEX cap Ø 14,25 mm e: 2 mm ProdEX RUSTIK 6 3 SPECIFIC ELEMENTS FOR THE HIDDEN FASTENING SYSTEM WITH CAPS GENERAL ACCESSORIES FOR THE CAP SYSTEM REFERENCE DESCRIPTION MATERIAL / FINISH PRCF005CAP Ø 14,25 2 ProdEX cap Ø 14,25 mm e: 2 mm ProdEX LIGHT BROWN PRGA008BRC Ø 10,5 Ø 5,5 8 Ø 14,5 Bit for fixed points Steel HSS PRCF006CAP Ø 14,25 2 ProdEX cap Ø 14,25 mm e: 2 mm ProdEX MINT Ø 14,25 PRGA009BRC Ø 10,5 Ø 7 8 Ø 14,5 Bit for floating points Steel HSS PRCF007CAP 2 ProdEX cap Ø 14,25 mm e: 2 mm ProdEX DEEP BROWN Ø 14, CAPS PRCF008CAP 2 ProdEX cap Ø 14,25 mm e: 2 mm ProdEX DARK BROWN REFERENCE DESCRIPTION MATERIAL / FINISH Ø 14,25 PRCF001CAP Ø 14,25 2 ProdEX cap Ø 14,25 mm e: 2 mm ProdEX CREAM PRCF009CAP 2 ProdEX cap Ø 14,25 mm e: 2 mm ProdEX NUX PRCF002CAP Ø 14,25 2 ProdEX cap Ø 14,25 mm e: 2 mm ProdEX ICE GREY PRCF010CAP Ø 14,25 2 ProdEX cap Ø 14,25 mm e: 2 mm ProdEX MOCCA To determine delivery times, minimum quantities, etc., contact Prodema (prodema@prodema.com). TORNILLO Acero inoxidable To determine delivery times, minimum quantities, etc., contact Prodema (prodema@prodema.com).

42 6 4 SPECIFIC ELEMENTS FOR THE HIDDEN FASTENING SYSTEM WITH HANGING STRUTS REFERENCE DESCRIPTION MATERIAL / FINISH GENERAL ACCESSORIES FOR THE HANGING SYSTEM PRFL005BRU Base piece for straight fixed louvers (0º) Rough REFERENCE DESCRIPTION MATERIAL / FINISH PRFL005RAL Base piece for straight fixed louvers (0º) Ral PRCF011BRU Exterior guide strip mm bar Aluminium 6063 Rough T5 PRFL006BRU PRFL006RAL Double base piece for straight fixed louvers (0º) Double base piece for straight fixed louvers (0º) Rough Ral PRCF012BRU Exterior hanging clips. Piece Aluminium 6063 Rough T5 PRFL007BRU PRFL007RAL Base piece for inclined fixed louvers (30º) Base piece for inclined fixed louvers (30º) Rough Ral PRCF013 PRCF014 11,5 25 Ø 6 Ø12 Ø 8 Ø13 Panel screw TB -A2 TX 30 Ø head 12 mm Ø screw 6 mm L: 11,5 mm Bolt T.H./INX A4 Ø head 13 mm Ø screw 8 mm L: 25 mm Stainless steel Stainless steel A2 PRFL008BRU PRFL008RAL PRFL009BRU PRFL009RAL PRFL010BRU Double base piece for inclined fixed louvers (30º) Double base piece for inclined fixed louvers (30º) Base piece for inclined fixed louvers (60º) Base piece for inclined fixed louvers (60º) Double base piece for inclined fixed louvers (60º) Rough Ral Rough Ral Rough 6 5 SPECIFIC ELEMENTS FOR THE FIXED LOUVER STYLE FASTENING PRFL010RAL Double base piece for inclined fixed louvers (60º) Ral GENERAL ACCESSORIES FOR THE FIXED LOUVER SYSTEM PRFL011BRU Slat support Rough REFERENCE DESCRIPTION MATERIAL / FINISH PRFL001BRU PRFL001RAL PRFL002BRU PRFL002RAL PRFL003BRU Perforated bar 20 mm wide 2000 mm long Perforated bar 20 mm wide 2000 mm long Perforated bar 20 mm wide 3000 mm long Perforated bar 20 mm wide 3000 mm long Non-perforated bar 2000 mm long Rough Ral Rough Ral Rough PRFL011RAL PRFL012BRU PRFL012RAL Slat support Slat support with clip Slat support with clip Non-perforated bar Ø 6 PRFL003RAL Ral largo 2000 mm Panel screw 9,5 TB - A2 TX 30 PRFL004BRU Non-perforated bar Rough largo 3000 mm PRFL013 Ø head 12 mm Stainless steel Ø screw 6 mm PRFL004RAL Non-perforated bar Ø12 L: 9,5 mm Ral largo 3000 mm Ral Rough Ral To determine delivery times, minimum quantities, etc., contact Prodema (prodema@prodema.com). TORNILLO To determine delivery times, minimum quantities, etc., contact Prodema (prodema@prodema.com).

43 REFERENCE DESCRIPTION MATERIAL / FINISH 6 6 SPECIFIC ELEMENTS FOR THE AMERICAN FAÇADE STYLE FASTENING SYSTEM PRFL014 Screw for perforated bar Rough GENERAL ACCESSORIES FOR THE AMERICAN FAÇADE STYLE FASTENING SYSTEM PRFL015BRU Anchorage 40 x 40 length 40 Rough REFERENCE DESCRIPTION MATERIAL / FINISH PRFL005RAL 40 Anchorage 40 x 40 length 40 Ral PRFL016BRU Anchorage 100 x 50 length 40 Rough PRFA001AND Panel support staple. Unit Steel A4 Black lacquer PRFL006RAL 40 Anchorage 100 x 50 length 40 Ral PRFL017BRU PRFL007RAL Anchorage 125 x 50 length 40 Anchorage 125 x 50 length 40 Rough Ral PRFA002MEC Machined slat 2440 x 190 ProdEX PRFL018BRU Anchorage 60 x 40 length 80 Rough PRFL018RAL 80 Anchorage 60 x 40 length 80 Ral PRFA003MEC Machined slat 2440 x 290 ProdEX PRFL019BRU Anchorage 100 x 50 length 80 Rough 80 PRFL019RAL Anchorage 100 x 50 length 80 Ral PRFL020BRU Anchorage 125 x 50 length 80 Rough 80 PRFL020RAL Anchorage 125 x 50 length 80 Ral PRFL021 T-M8 25 bolt Inox. PRFL022 DIN 943 M8 stainless steel nut Inox. PRFL DIN 125 A stainless steel washer Inox. * All RAL finishes are offered for selection in the following manner: Direct matt silver anodized / 15 micra RAL color chart FUTURA color chart * Finishes available for each choice: GLOSS or MATTE To determine delivery times, minimum quantities, etc., contact Prodema (prodema@prodema.com). TORNILLO Acero inoxidable