KEITH PANEL SYSTEMS FUNDERMAX- MAX EXTERIOR EXPOSED FASTENER PRESSURE EQUALIZED WALL SYSTEM
|
|
- Jason Price
- 5 years ago
- Views:
Transcription
1 S Y S T E M D E T A I L S FUNDERMAX- MAX EXTERIOR EXPOSED FASTENER PRESSURE EQUALIZED WALL SYSTEM
2 PAGE TITLE PAGE Table of Contents Fundermax Max Exterior Product Information Design and Installation Information Sample Elevation Typical Vertical Joint Outside Corner Inside Corner Window Jamb Typical Horizontal Joint Mid-panel Fastener Support Base Window Sill Window Head Floor Slab Deflection and Thru-wall Flashing Parapet 1 2 3, TABLE OF CONTENTS 1
3 TECHNICAL DATA Density Flexural Strength Modulus of Elasticity Tensile Strength Thermal Expansion Coefficient 1.35 g/cm 3 80 MPa ~9000 MPa 60 MPa 18x K Test Method EN ISO EN ISO 178 EN ISO 178 EN ISO DIN Fire Behavior Weight - 8mm ( 5 16") thickness Euroclass B-s2, d0 for 6-10mm ~10.8 kg/m² ~2.21 lbs/ft² EN PANEL SIZES GR SP JU XL 2800 x x x x 1854 imperial values 110" x 51" 110" x 73" 161" x 51" 161" x 73" Tolerances +10mm -0mm (EN 438-6,5.3) Panel formats are production formats. If exact dimensions and angles are necessary, we recommend an all-sided blank. Edge Processing To mill bevels electric hand planes with bevel or bevel grooves can be used or hand routers. Expansion / Contraction Max Exterior shrinks when it loses moisture and expands when it absorbs moisture. Calculate: overall length 500 = change in length Curved Max Exterior Panels Top and bottom edge profiles (2mm thick) must be pre-bent. Only sliding line fastenings are allowed (no point fastenings). The straight ends and joints of the exterior panels must likewise be edged. (U-profile, H-profile). Min. radius 3m(9'-10") and min. length 1.3m(4'-3"). Sealent The use of sealant compounds must be avoided as they can cause permanent staining to Max Exterior panels. MAX EXTERIOR PRODUCT INFORMATION 2
4 Panel Joints To be minimum 8mm wide for vertical and horizontal joints. The wider any joint, the less noticeable are inaccuracies in width. Therefore typical joint width used is 13mm. Panel Attachment Layout Spacing of rivet fasteners to be spread equally on panel. See below for edge distance and spacing requirements. Ventilaton Cavity The effectiveness of a pressure equalized system depends on a clear minimum air cavity depth as determined by building height. The cavity may not be reduced by horizontal profiles or any stray objects such as loose wind proofing layers, etc... Minimum cavity thickness as per table below: Height of wall system between cavity intake and exhaust Min. uninterrupted ventilated cavity up to 6m (18') 20mm ( 13 16") up to 25m (75') up to 50m (150') 30mm 40mm (1 3 16") (1 9 16") Single span panel. up to 75m (225') 50mm (2") > than 75m (225') 60mm (2 3 8") Ventilation Cavity Intake/Exhaust Air cavity ventilation openings provided at the base and top of the wall area and at any additional interruptions for example window heads and sills. Panel Attachment For fixing onto aluminum subframe, use Fundermax specified aluminum rivets. For fixing onto steel subframe, use Fundermax specified stainless steel rivets. Rivet saucer head is 15mm Ø painted corresponding colour with Max Exterior panel. A EPDM washer gasket is placed under rivet head to provide weather seal. For wood subframe stainless steel screws will be provided. Double span panel. Minimum distance to panel edge: Horizontal and Vertical = 20mm ( 13 16") Maximum distance to panel edge: Horizontal and Vertical = 80mm (3 1 8") Engineering Loads Max Exterior 8mm thickness fastener spacings 0.50 kn/m² 1.00 kn/m² 1.50 kn/m² 2.00 kn/m² Single span A = 700mm (27.5") B = 700mm (27.5") A = 539mm (21.2") B = 700mm (27.5") A = 373mm (14.7") B = 700mm (27.5") A = 280mm (11.0") B = 700mm (27.5") Double span A = 700mm (27.5") B = 700mm (27.5") A = 399mm (15.7") B = 700mm (27.5") A = 320mm (12.6") B = 700mm (27.5") A = 293mm (11.5") B = 700mm (27.5") DESIGN AND INSTALLATION INFORMATION 3
5 Max Exterior Panel Expansion/Contraction To allow expansion and contraction between the substructure and panels, all holes drilled in Max Exterior are oversized from the rivets body diameter. In order to hold up the panel, 1 rivet per panel is fixed by infilling the oversized hole with an aluminum or stainless steel sleeve. In addition to the fixed point, a loose point is placed in the same level. Position of the fixed and loose points will be determined on shop drawings. Site Fabricating Panels Avoid using tools which produce fine dust. Always work out of the weather. Always drill/cut perpendicularly to the panel surface. Use circular saw with straight edge with dust extraction. For best cut use a Blad hard metal teeth TF or diamond tipped saw blade. Use jig say for hole cut outs in panel. Dust from fabrication must be removed from panel surface immediately following cutting. Site Storage Max Exterior panels must be stacked horizontally on flat, stable supports and supporting panels. The goods must lie completely flat. Cover plates must always be left on the stack. The top cover should be weighted down. After removal of panels, PE films must again be closed over tyhe stack. The same applies, in principle, for cut-panel stacks. Incorrect storage can lead to permanent deformation of the panels. Max Exterior panels are to be stored in closed rooms under normal climatic conditions. Climate differences on the two surfaces of a panel are to be avoided. With pre-installed fastening elements, therefore, care is to be taken that the climatic effect is uniform on all sides. Use intermediate layers of wood or plastic. DESIGN AND INSTALLATION INFORMATION 4
6 SAMPLE ELEVATION 5
7 TYPICAL VERTICAL JOINT 6
8 OUTSIDE CORNER 7
9 INSIDE CORNER 8
10 WINDOW JAMB 9
11 TYPICAL HORIZONTAL JOINT 10
12 MID-PANEL FASTENER SUPPORT 11
13 BASE 12
14 WINDOW SILL 13
15 WINDOW HEAD 14
16 FLOOR SLAB DEFLECTION & THRU-WALL FLASHING 15
17 PARAPET 16
KEITH PANEL SYSTEMS FUNDERMAX- MAX EXTERIOR CONCEALED FASTENERS PRESSURE EQUALIZED WALL SYSTEM
S Y S T E M D E T A I L S FUNDERMAX- MAX EXTERIOR CONCEALED FASTENERS PRESSURE EQUALIZED WALL SYSTEM PAGE TITLE PAGE Table of Contents Fundermax Max Exterior Product Information Design and Installation
More informationHOLLOW CORRUGATED SHEETS
P R O D U C T C A T A L O G U E HOLLOW CORRUGATED SHEETS www.tuflite.com Bangalore (Head Office) #240/1, Ganesh Krupa, 18th Cross, Sadashivanagar, Bangalore- 560 080, India P: +91 80 4252 5252 F: +91 80
More information40mm Thermoclick. Type II Class 1 Clear Satin Anodize - 201R1 (Mid Grade Commercial)
http://www.sundancesupply.com 40mm Thermoclick Type II Class 1 Clear Satin Anodize - 201R1 (Mid Grade Commercial) U-Profile 12' Lengths $39 Out System offers a complete set of extrusions and accessories
More informationEXPOSED FASTENING SYSTEM WITH SCREWS OR RIVETS
External EXPOSED FASTENING SYSTEM WITH SCREWS OR RIVETS Parklex Facade may be installed using mechanical fasteners, such as screws or rivets. The panels are attached to vertical battens. In the event that
More informationResysta 6 and 4 Flat Board Siding System Assembly Installation Guidelines
Resysta 6 and 4 Flat Board Siding System Assembly Installation Guidelines NOTE: Proper planning of the siding layout is essential for ease of installation of siding boards and siding components. Thoroughly
More informationAluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement
Aluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement 1 Aluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement The following instructions are a supplement
More informationStorefront Installation Guide
Storefront General Notes: 1. Check Contract Documents and Shop Drawings. Understand and clarify any Field Verify Notes and approvals of drawings and products to be familiar with the project. Installation
More informationBalConIEs.
BalConIEs Installation guidelines for balustrade cladding The following regulations and provisions must be observed when preparing and installing balustrade cladding using Trespa Meteon sheets: 防 The applicable
More informationFABRICATION MANUAL CCM Copper Composite You discover why ALPOLIC Copper composite material (CCM) is the building material of the future as soon as
FABRICATION MANUAL CCM Copper Composite You discover why ALPOLIC Copper composite material (CCM) is the building material of the future as soon as you fabricate it. Our CCM is as easy to fabricate as wood:
More informationInstallation Guide: NC 25 System
Installation Guide: NC 25 System Table of Contents INSTALLATION GUIDE: NC 25 SYSTEM 1 PROPER STORAGE AND HANDLING 3 SUITABLE SUBSTRATES 3 FLASHING 3 MOISTURE BARRIER 4 METAL CHANNELS/COMPONENTS 4 STAINLESS
More informationKS42 MF SERIES - HORIZONTAL INSTALLATION
CI-DS-01-KSMF H CI-PJ-01-KSMF H CI-PJ-02-KSMF H CI-PJ-03-KSMF H CI-PJ-04-KSMF H CI-PJ-05-KSMF H CI-PJ-06-KSMF H CI-PJ-07-KSMF H CI-PJ-08-KSMF H CI-PJ-09-KSMF H CI-PJ-10-KSMF H CI-PJ-11-KSMF H CI-PJ-12-KSMF
More informationDW HORIZONTAL INSTALLATION
AR-PJ-01-DW2H 2" HORIZONTAL PANEL JOINT AR-PJ-02-DW2H 2" VERTICAL PANEL JOINT AR-PJ-03-DW2H 3" HORIZONTAL PANEL JOINT AR-PJ-04-DW2H 3" VERTICAL PANEL JOINT AR-PJ-05-DW2H CUSTOM REVEAL AR-PJ-06-DW2H DW-2000S
More informationSTACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS
STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS 1290363 Revision 1 12/16 Page 1 Weather Shield Mfg., Inc. NOTICE CAUTION! Failure to install and maintain our product according to these instructions
More informationInstallation Instructions
Installation Instructions Roof edge trim profile Series TAG multi-piece aluminium profile Front face height: 250-1050 mm supplied with patented 4F brackets as standard height-adjustable, horizontally moveable,
More informationSeries Sloped glazed Curtain wall. Installation Instructions
Series 5600 Sloped glazed Curtain wall Installation Instructions Part NO. Y308 February 2013 SECTION TABLE OF CONTENTS PAGE I. General Notes & Guidelines. 3-4 II. Gutter and Mullion Assembly.. 5 III. End
More informationWall mounting with holding profile
B Main profile C Edge profile D Wall spacer E Heradesign acoustic panel Edge distance max. 250 mm c Centre distance of basic section (see table) B max. 600 mm or 625 mm a Centre distance of spacer (see
More information900 SERIES WALL PANELS
CI-DS-01-900 CI-PP-01-900 CI-PJ-01-900 CI-PJ-02-900 CI-PJ-03-900 CI-BS-01-900 CI-BS-02-900 CI-BS-03-900 CI-BS-04-900 CI-BS-05-900 CI-OC-01-900 CI-OC-02-900 CI-IC-01-900 CI-FO-01-900 CI-FO-02-900 CI-FO-03-900
More informationDW VERTICAL INSTALLATION
AR-PJ-01-DW5V AR-PJ-02-DW5V AR-PJ-03-DW5V AR-PJ-04-DW5V AR-BS-01-DW5V AR-BS-02-DW5V AR-OC-01-DW5V AR-OC-02-DW5V AR-OC-03-DW5V AR-IC-01-DW5V AR-IC-02-DW5V AR-IC-03-DW5V AR-FO-01-DW5V AR-FO-02-DW5V AR-FO-03-DW5V
More informationNATURA PRO Product Information Leaflet 1
NATURA PRO Product Information Leaflet 1 1. Product composition NATURA PRO sheets consist of the following: Portland cement Mineral fillers Organic reinforcing fibers Additives Semi-transparent water-based
More informationCONTENTS OVERVIEW. For a complete set of CAD drawing details, please visit LaminatorsInc.com. 1 Essential Equipment. 1 Essential Supplies
LaminatorsInc.com CONTENTS 1 Essential Equipment 1 Essential Supplies 2 Panel Preparation 4 Panel Extrusion Preparation 5 Panel Assembly 6 Wall Sheathing Preparation (Over Plywood) 6 Wall Sheathing Preparation
More informationInstallation Instructions: Urbanline Alu Selekta Clad
Product description Ecology Technical data Urbanline Alu Selekta Clad (selekta façade profiles and heritageselekta façade profiles) are identical in terms of their core material and surface texture. However,
More informationSide Light Frame Pack Assembly Instructions
Please read this complete set of assembly instructions before starting the installation and only when you understand the construction method start to follow the step by step guide. IDENTIFY THE PACK CONTENTS
More informationWave Profile Installation Guide
Wave Profile Installation Guide American Pa o Covers Plus Proudly Builds With Tools & Hardware Wave Profile Installation Guide Tape Measure Square Level Felt tipped Marker and/or grease pencil 3/8" Nut
More information-ARBOREAL. Skanfas Ltd Rikkilän/e 993 FIN Simola
Skanfas Ltd Rikkilän/e 993 FIN-54330 Simola www.skanfas.com Installation Instructions Skanfas is a fire-proof, weather-proof and non-decaying facade material. It is a combination of the pleasant look of
More informationSide Light Frame Pack Assembly Instructions
Side Light Frame Pack Assembly Instructions Please read this complete set of assembly instructions before starting the installation and only when you understand the construction method start to follow
More informationMETL-VISION WINDOW SYSTEM FOR HORIZONTAL WALL PIONEERING INSULATED METAL PANEL TECHNOLOGY
METL-VISION WINDOW SYSTEM FOR HORIZONTAL WALL Window assembly GUIDE PIONEERING INSULATED METAL PANEL TECHNOLOGY PIONEERING INSULATED METAL PANEL TECHNOLOGY CONTENTS DETAIL TITLE FILE NO. PAGE NO. INTRODUCTION..................................................................
More informationProcessing and design Solid Textile Board
Processing and design Solid Textile Board List of contents Introduction Kerfing Joints and assembly Increasing thickness and stiffness Edges Cutting Milling and drilling Three-dimensional pressing Surface
More informationYES 45 TU Thermal Storefront System Installation Manual
Installation Manual 2004 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................ Page ii PARTS DESCRIPTION Framing
More informationInstallation Guide (888)
BamDeck Installation Guide (888) 788-2254 The Collection Decking Systems BAMDECK 4G 5-7/16 Wide Plank Dims: 192 L x 5-7/16 W x 13/16 H BAMDECK 4G WIDE 8-1/4 Wide Plank Dims: 96 L x 8-1/4 W x 13/16 H BAMDECK
More informationYES 40 FS/FI Storefront System Installation Manual
Installation Manual 2014 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page ii PARTS DESCRIPTION YES 40 FS Framing Members... Page 1 YES 40
More informationInstallation Manual for M4-Exterior Sheathing
Installation Manual for M4-Exterior Sheathing 1 Application Area - Testing M4 complying with: 2015 and 2012 International Building Code (IBC) and 2015 and 2012 International Residential Code (IRC). The
More informationInstallation Instructions
www.marlite.com Effective Date 03/01/2018 ARTIZAN FRP, SYMMETRIX FRP, ENVUE FRP, STANDARD FRP Installation Instructions Statements expressed in this technical bulletin are recommendations for the application
More informationEndura-Classic Craftsman Information
Endura-Classic Craftsman Information Endura Classic Craftsman Series Columns have a Limited Lifetime Warranty against rot, corrosion and moisture damage. Endura Classic Craftsman Series Columns are manufactured
More informationSAGIREV Installation Manual
SAGIPER North America Inc 13179 156 Street Edmonton, AB Canada T5V 1V2 T: (780) 482-3445 F: 1 (888) 870-7069 www.sagipernorthamerica.com SAGIREV Installation Manual NOTE: This guide has been prepared and
More informationInstallation Instructions
Installation Instructions 200 Series Curtainwall 3056 WALKER RIDGE DR. NW, SUITE G WALKER, MI 49544 800-866-2227 dependable@tubeliteinc.com Revised April 2014 dependable@tubeliteinc.com Page 1 TABLE OF
More informationHANDRAIL HEIGHT PER LOCAL CODE AUTORITY
WITH WOOD END CAPS PLEASE READ PLEASE READ THESE INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING THE INSTALLATION! 3" [77.3mm] THIS INSTRUCTION SHEET IS INTENDED TO PROVIDE A SPECIFIC GUIDE TO FOLLOW FOR THE
More information400 SERIES VERTICAL INSTALLATION
CI-DS-01-400V CI-PJ-01-400V CI-PJ-02-400V CI-PJ-03-400V CI-BS-01-400V CI-BS-02-400V CI-BS-03-400V CI-BS-04-400V CI-BS-05-400V CI-OC-01-400V CI-OC-02-400V CI-IC-01-400V CI-IC-02-400V CI-FO-01-400V CI-FO-02-400V
More informationKS SERIES - VERTICAL INSTALLATION
CS-DS-01-KSV CS DISCLAIMER CS-PJ-01-KSV KS42SL EXPANDED PANEL JOINT CS-PJ-02-KSV KS42SL ENGAGED PANEL JOINT CS-PJ-03-KSV KS45SL EXPANDED PANEL JOINT CS-PJ-04-KSV KS45 FLAT ENGAGED PANEL JOINT CS-PJ-05-KSV
More informationTIMBER HANDRAILS & BALUSTRADES
TECHNICAL DATA SHEET ISSUED BY TIMBER QUEENSLAND TIMBER HANDRAILS & BALUSTRADES 3 RECOMMENDED PRACTICE // MARCH 014 This data sheet provides general guidance on member sizes, connections and suitable materials
More informationInstallation Guide (888)
BamDeck Installation Guide (888) 788-2254 The Collection Decking Systems BAMDECK 3G 5-7/16 Wide Plank Dims: 96 L x 5-7/16 W x 13/16 H BAMDECK 3G 16FT. 5-7/16 Wide Plank Dims: 192 L x 5-1/2 W x 13/16 H
More informationALUMINUM PIPE GUIDERAIL 01/01/
NOTES PIPE RAILING & POSTS: Structural Tube, Pipe and Bar shall be in accordance with ASTM B22 or ASTM B429, Alloy 606-T6. End Rail 90 bends and corner bends with maximum 4-0" post spacing, may be Alloy
More informationNARROW, MEDIUM AND WIDE STILE, THERMASTILE AND DURASTILE. Installation Instructions
NARROW, MEDIUM AND WIDE STILE, THERMASTILE AND DURASTILE Installation Instructions PART Y015 JUNE 2016 Table of Contents Section 1. GENERAL NOTES AND GUIDELINES... 2. DOOR HARDWARE A. Locks B. Push/Pulls
More informationWESTERN WAVE Panel. Horizontal Installation and Technical Information
WESTERN WAVE Panel Horizontal Installation and Technical Information Western States Western Wave Wall and Soffit Panels Installation, Flashings & Shop Drawing Detail Guide Table of Contents Section Page
More informationTruGrain 6 and 4 Flat Board Siding System Assembly Installation Guidelines
TruGrain 6 and 4 Flat Board Siding System Assembly Installation Guidelines NOTE: Proper planning of the siding layout is essential for ease of installation of siding boards and siding components. Thoroughly
More informationSite Preparation Information for:
Site Preparation Information for: Product Series - Big Doors Product Type - MultiGlide Door Read these instructions and the Product Safety Information before starting procedure. For: MultiGlide Door Instructions/Videos
More informationWESTERN WAVE Panel. Vertical Installation and Technical Information
WESTERN WAVE Panel Vertical Installation and Technical Information Western States Western Wave Wall and Soffit Panels (Vertical) Installation, Flashings & Shop Drawing Detail Guide Section Notes to Designer
More informationCOMPOSITE SIDING INSTALLATION GUIDE
CENTURY HOME LIVING COMPOSITE SIDING INSTALLATION GUIDE Read all instructions prior to installing any siding product. Failure to install and finish this product in accordance with all local building codes,
More informationTable saws are not recommended for cutting sheets larger than 4'X4' I size.
Aluminum Composite Panel (Fabrication) Considerable care should be taken in the layout and handling of Aluminum Composite Panel. The use if coolants or lubricants are not required when sawing. A. Sawing
More informationGENERAL INSTALLATION GUIDELINES
1551 MT. ROSE AVENUE YORK PA 17403-2909 (717) 849-8100 GENERAL INSTALLATION GUIDELINES For Receptor Systems Approved 08/31/2018 Installation Guideline Disclaimer This document contains general installation
More informationCROSSBAR RAFTER ISOMETRIC
Super Sky Products' typical glazing system consists of glass panels or "lites" which are attached to the main framing members using extruded aluminum "retainers" or "pressure plates". These retainers are
More informationXL JOINERY LTD LA PORTE VISTA MODULAR 3 ASSEMBLY INSTRUCTIONS
XL JOINERY LTD LA PORTE VISTA MODULAR 3 2090mm High x 4687mm Wide ASSEMBLY INSTRUCTIONS READ AND UNDERSTAND THESE INSTRUCTIONS FULLY PRIOR TO STARTING INSTALLATION. IT IS STRONGLY RECOMMENDED THAT A COMPETENT
More informationDIANE MODEL PASS-THRU
INSTALLATION INSTRUCTIONS MODELS D101 AND D10 DIANE MODEL PASS-THRU 50 E. Vernon Avenue, Los Angeles, CA 90058-186 Phone: (800) 41-6144 EXT. 7760 Fax: (800) 458-7496 crlaurence.com Email: transaction@crlaurence.com
More informationSubframe Installation Guide
FACADE TECHNOLOGY THE FIXING DOES NOT REQUIRE A RAINSCREEN AND HAS PASSED CSIRO AS484-995 WEATHER PERFORMANCE 7.5 AND STRUCTURAL TEST 7.3 HAS ALSO PASSED NATA ACCREDITATION CYCLONE TESTING AS4040.3 600mm
More informationYES 600 Thermal Clip Storefront System Installation Manual
Installation Manual 2004 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................ Page ii Frame Types............................................
More informationUlltraclad Aluminium Cladding. Contents. 1.0 General Information Design Information Installation Information 7. 4.
Ulltraclad Aluminium Cladding Contents 1.0 General Information 2 2.0 Design Information 4 3.0 Installation Information 7 4.0 Maintenance 10 5.0 Health & Safety 10 1 1.0 General Information 1.1 Introduction
More informationSwisspearl LARGO panels. DIM Design + Installation Manual
Swisspearl LARGO panels DIM Design + Installation Manual Rain screen cladding 2 Panel, technical data 2 General information 3 Design and installation 4 System components and accessories 6 Exterior wall
More informationYCW 750 OG Outside Glazed Curtain Wall System Installation Manual
YCW 750 OG Outside Glazed Curtain Wall System Installation Manual 2004 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................
More informationCurtain Wall Installation Guide
Curtain Wall Installation Guide Curtain Wall Installation Guide 1 IMPORTANT NOTICES! Important Notices & Information Manufacturer s Notes: The building envelope must be correctly prepared with weather
More informationC.00. Ullrich Aluminium Co. Ltd. Ulltraclad Aluminium Cladding September Wall Batten Elevation. Horizontal battens between verticals at soffit
Horizontal battens between verticals at soffit 2 C.04 600 600 600 600 Cavity batten at 600 mm centres 1 C.03 Batten fixing points 1 C.04 1 C.07 1 C.12 1 C.13 1 C.14 Meter Box Window 1 C.08 1 C.09 800 800
More informationDECK 30 & DECK 30 XS DECKING BOARDS hollow and solid 30 cm boards
DECK 30 & DECK 30 XS DECKING BOARDS hollow and solid 30 cm boards terrace - footpath - foot bridge - roof terrace TECHNICAL INSTALLATION GUIDE Ref LTGP 06/2015-010 TO READ CAREFULLY IMPORTANT INFORMATION
More informationFir and pine wood (52 %) Portland cement (38 %) made by firing limestone and clay Water (9 %) Wood mineralisation substances (1 %)
Duripanel Structura Product information sheet 1 1 Product composition Duripanel Structura fibre panels are made from: Fir and pine wood (52 %) Portland cement (38 %) made by firing limestone and clay Water
More informationOverlapping panel Cladding system made up of horizontal overlapping panels fixed on a wooden or metal wall-mounted framework.
facade Overlapping panel Cladding system made up of horizontal overlapping panels fixed on a wooden or metal wall-mounted framework. Specification and installation guide Presentation of the system VMZ
More information14000 I/O Series Flush Glaze. Fabrication and Installation Instructions
14000 I/O Series Flush Glaze Fabrication and Installation Instructions Last saved on 12/18/2009 Table of Contents GENERAL CONSTRUCTION NOTES...3 EXTRUDED ALUMINUM PARTS...4 ACCESSORIES...5 OVERVIEW...6
More informationFabrication and Installation
Fabrication and Installation Fabrication and Installation 1. Processing methods 24 2. Installation procedures 25 3. Precautions on fabrication and installation (Important) 28 4. Examples of installation
More informationINSTALLATION GUIDE DUOFUSE SLAT WALL SYSTEM
06/2013 ENG 1 INSTALLATION GUIDE DUOFUSE SLAT WALL SYSTEM The Duofuse wood composite slat wall system is much more durable than wooden fences, and correct installation is necessary to enjoy the fences
More informationExtrusions GB-3-IN01. Updated: Scale: REV: - This Drawing is Protected by Copyright Altus NZ Ltd.
Extrusions Updated: N/A Scale: N.T.S REV: - Dwg Dwg Revision Rev No Description Description Date GB-3-IN01 Index Page - - - - - GB-3-001 Extrusions - - - - - GB-3-002 Extrusions - - - - - GB-3-003 Extrusions
More informationSTEEL PIPE GUIDERAIL 01/01/
NOTES PIPE RAILING & POSTS: Pipe Rails and s shall be in accordance with ASTM A5 Grade B for standard weight pipe and ASTM A500 Grade B, C or D or ASTM A50 for structural tube. Bars for handrail supports
More informationSwisspearl Large size panels. DIM Design + Installation Manual
Swisspearl Large size panels DIM Design + Installation Manual General information 3 Design and installation 4 System components and accessories 6 Exterior wall / sub frame types 7 Metal sub frame 8 Timber
More informationFaçade CUT-TO-SIZE FAÇADE STRIPS APPLICATION IN OVERLAP ON WOODEN SUPPORTING STRUCTURE APPLICATION INSTRUCTIONS 1 1. GENERAL
Façade CUT-TO-SIZE FAÇADE STRIPS APPLICATION IN OVERLAP ON WOODEN SUPPORTING STRUCTURE APPLICATION INSTRUCTIONS 1 1. GENERAL These application instructions are specifically intended for the fastening of
More informationWindow Frame Installation Instructions For Nail-on and Block Frames
General The key to any window or door installation is preparation. This extends from storage of the product to the final installation and to all points in between. Careful planning and attention to detail
More informationYES 45 XT High Performance Thermal Storefront System
Dual Thermal Barrier ThermaBond Plus Pour & Debridge Technology Installation Manual 2015 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page
More informationYES 45 FS/FI Storefront System Installation Manual
Installation Manual 2014 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page ii PARTS DESCRIPTION YES 45 FS Framing Members... Page 1 YES 45
More informationGENERAL INSTALLATION GUIDELINES
1551 MT. ROSE AVENUE YORK PA 17403-2909 (717) 849-8100 GENERAL INSTALLATION GUIDELINES For Receptor Systems Approved 9/29/2017 Installation Guideline Disclaimer This document contains general installation
More informationSeries Advanced and alternate. Installation Instructions
Series 5500 Advanced and alternate Installation Instructions Part NO. Y557 February 2013 TABLE OF CONTENTS SECTION S-5500 ADVANCED INSTALLATION INSTUCTIONS PAGE I. General Notes and Guidelines...... 3-4
More informationThe Passive Fire Protection Handbook
Uniclass L5:P:N3 CI/SfB Rf9 EPIC E:X:Y41 (K)+(K3) December 003 NBSPlus The Passive Fire Protection Handbook VICUCLAD VICUCLAD Applications Fire protection of metal ducts Construction of smoke extract ducts
More information1 Nu-core. Nu-core panels are an innovative step forward in the decorative cladding industry.
Fabrication Manual While keeping with the advantages of common Aluminium and Metal composite panel materials, Nu-core have greatly improved panel characteristics by utilizing more natural core materials,
More informationWall flashing profiles FP 60 WA 1 WA 150 WA 1 - ÜK WA 1 - Ü 150 E
Wall flashing profiles FP 60 WA 1 WA 150 WA 1 - ÜK 150-275 WA 1 - Ü 150 E 1 F Ü R D I E ZU K U N FT G E DAC HT. The alwitra waterproofing system alwitra wall flashing profiles are part of the practically
More informationinstallation care & maintenance instructions lifecycledecking.com 25-year limited residential warranty 20-year limited commercial warranty
installation care & maintenance instructions lifecycledecking.com 25-year limited residential warranty 20-year limited commercial warranty Installation Instructions As with any building project, use proper
More informationYCW 752 Outside Glazed Curtain Wall System Installation Manual
YCW 752 Outside Glazed Curtain Wall System Installation Manual 2007 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................
More informationBuildingEnvelope Oldcastle ( ) -
BuildingEnvelope 1-866-Oldcastle (653-2278) - www.obe.com RELIANCE -LT CURTAIN WALL 2" X 7-1/2" / POLYAMIDE PRESSURE PLATE / 1" GLAZING Elev-Reliance-LT-750-PolyPP H0042-Steel-Anchor H5021-ShrBlk-Anchors
More information4 1/2" [114.3mm] HANDRAIL HEIGHT PER LOCAL CODE AUTHORITY
WITH INTERNATIONAL OFFSET PLEASE READ PLEASE READ THESE INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING THE INSTALLATION! THIS INSTRUCTION SHEET IS INTENDED TO PROVIDE A SPECIFIC GUIDE TO FOLLOW FOR THE INSTALLATION
More informationINSTALLATION SHOP DRAWINGS FOR MINNEAPOLIS, MN
MINNEAPOLIS, MN 2-0- 2-- General Notes Abbreviations Deviations from Architectural Specifications Deviations from Architectural Drawings ALUM. = ALUMINUM B.O. = BY OTHERS CONT. = CONTINUOUS. = CLEARANCE
More informationSHIPLOCK CLADDING PRODUCT GUIDE INSTALLATION TECHNICAL SPECIFICATIONS CARE & MAINTENANCE
SHIPLOCK CLADDING PRODUCT GUIDE INSTALLATION TECHNICAL SPECIFICATIONS CARE & MAINTENANCE SHIPLOCK CLADDING CN-04E / CN-04W / CN-W008 Prior to the installation of any form of Cladding, it is recommended
More information50948-RHN Putney. 06 January This document includes: Aluminium strip/ sheet coverings/ flashings 1. Code Section Revision Dated
50948-RHN Putney 06 January 2018 This document includes: Code Section Revision Dated H72 Aluminium strip/ sheet coverings/ flashings 1 Table of Contents Title H72 Aluminium strip/ sheet coverings/ flashings
More informationFaçade System Trimoterm FTV INVISIO
Façade System Trimoterm FTV INVISIO Façade System Trimoterm FTV INVISIO - Technical Document EN Version December 0 TABLE OF CONTENTS Technical description of the Facade system with Hidden Fixing FTV INVISIO.
More informationHow to Build Good Decks..
How to Build Good Decks.. Worldwide Sleeping Company, Inc Cary, North Carolina Decking Overview.. Decking Overview.. more Decking Joist.... Joist Hanger Ledger Lag Screw House Wall Decking House Floor
More information3" [76.0mm] HANDRAIL HEIGHT PER LOCAL CODE AUTHORITY
WITH OPTIONAL S.S. S PLEASE READ PLEASE READ THESE INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING THE INSTALLATION! THIS INSTRUCTION SHEET IS INTENDED TO PROVIDE A SPECIFIC GUIDE TO FOLLOW FOR THE INSTALLATION
More informationEffective February, 2015
Effective February, 2015 Table of Contents Ensuring System Performance 1 Components 2 Frequently Asked Questions 3 List of Tools 3 Before you Begin Preparation 3 Quality Tips 4 Cold Weather Tips 4 Cleaning
More informationINSTALLATION INSTRUCTIONS 2 x 4 1/2 for 1 Glass
INSTALLATION INSTRUCTIONS 2 x 4 1/2 for 1 Glass Deep pocket allows for direct anchor attachment to substrate without flat filler plate. 1/4 Ø perimeter anchor holes allows for direct anchor attachment
More informationGLOSSARY OF TERMS SECTION 8
GLOSSARY OF TERMS SECTION 8 Anchor Bolt Angle Base Plate Bay Blocking CCB Centerline Chord Cladding Clip Closure Strip An A-307 steel bolt embedded in the concrete footing to anchor the base plate of the
More informationYCW 750 IG Inside Glazed Curtain Wall System Installation Manual
Installation Manual 2014 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page ii PARTS DESCRIPTION YCW 750 IG Framing Members... Page 1 to 3
More informationTOLL FREE:(888) FAX:(941) ASSEMBLY of ProTEC CONCRETE STRUCTURAL INSULATED PANEL
ASSEMBLY of ProTEC CONCRETE STRUCTURAL INSULATED PANEL The ProTEC panels are manufactured with grooves on all four sides to accept the steel components. This grooving applies to the regular panel whose
More informationInstallation Instructions: Urbanline Euro Selekta Clad
Product description Ecology Technical data Urbanline Euro Selekta Clad (selekta façade profiles and heritageselekta façade profiles) are identical in terms of their core material and surface texture. However,
More informationHOW TO INSTALL ELITE PANELED WAINSCOTING Using X-Rails with Either Raised, Flat or Beaded Panels
HOW TO INSTALL ELITE PANELED WAINSCOTING Using X-Rails with Either Raised, Flat or Beaded Panels 1. First, remove the cover plates from all electrical outlets. All baseboards should also be removed; the
More informationTable and Furniture Base Fittings Plinth Adjusting Fittings
Adjusting screw with M8 or M thread Rigid, for glide inserts, steel thread Finish/Colour: Black, thread galvanized Version: With acceptance Ø30 mm Thread M8 650.22.381 M 650.22.382 Packing: 1 or 0 pcs.
More informationRoof fastener. Perfectly thought out for every roof
Roof fastener Perfectly thought out for every roof 1 Welcome to the world of clever solutions Solutions for every roof In our production areas we produce all needed components for the sub construction
More informationTENSILKUT ENGINEERING
TENSILKUT ENGINEERING For Accurate Test Specimens Manufacturer of equipment for the accurate preparation of physical test specimens since 1955 SIEBURG INTERNATIONAL, INC. 1901 Clydesdale Street, Maryville,
More informationYCW 750 OG Outside Glazed Curtain Wall System Installation Manual
YCW 750 OG Outside Glazed Curtain Wall System Installation Manual 2012 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes... Page ii PARTS DESCRIPTION
More informationINSTALLATION INSTRUCTIONS FOR REPLACEMENT FORGENT WOOD GLASTRA WINDOWS RECOMMENDATIONS FOR COMMON INSTALLATION OF ALL REPLACEMENT WINDOWS.
INSTALLATION INSTRUCTIONS FOR REPLACEMENT FORGENT WOOD GLASTRA WINDOWS RECOMMENDATIONS FOR COMMON INSTALLATION OF ALL REPLACEMENT WINDOWS. Installer: DO NOT DISCARD Please leave the Installation Guide
More informationSILVERBACK INSTALLATION MANUAL
SILVERBACK INSTALLATION MANUAL R-SERIES SOLAR RACKS T OLL FREE 866-766-3727 WWW.ROOFSCREEN.COM Introduction... 2 The Silverback Solar Racking System... 2 This manual... 2 Application... 2 System Overview...
More information