Beam/slab grip with ratchet

Transcription

1 Beam/slab grip with ratchet An indispensable aid for carpenters Beam/slab grip = less force required The beam/slab grip with ratchet is an indispensable aid for carpenters. Whether you want to align a roof truss or carry out other carpentry work, the beam/slab grip allows you to prestress timber quickly and easily. Beam grip with ratchet, forged steel Advantages beam grip Drop forged hooks No risk of splitting while driving in High-quality lead screw 320 mm ratchet length for optimum load transmission Double-sided handling thanks to clockwise/counterclockwise selector Art. no. Dimensions (mm) Span width (mm) PU Up to Bracing strap tensioner suitable for the beam grip with ratchet Slab grip properties Boss plate rotates through attachment points per boss plate: 8 x Ø 9 mm, 3 x Ø 12 mm Maximum span: 670 mm Advantages of the slab grip Minimal processing marks thanks to attachment using timber-construction screws Suitable for hard-to-reach locations (e.g. in angled areas such as roof slopes, etc.) Allows corner joints to be drawn together Suitable for timber types with an increased risk of cracking and splintering Art. no. Strap PU for 2 mm bracing strap 1 Slab grip with ratchet 162 Art. no. Span width (mm) PU Up to 670 2

2 Carpenter s hammer Eurotec carpenter s hammer The carpenter s hammer is used primarily in timber-frame construction but also in formwork. One side of the hammer is for driving in nails, and the other has a claw with an extended point on one side. The surface of the hammer face is ribbed in order to prevent it slipping off the nail heads. The Eurotec carpenter s hammer is fitted with a magnetic nail holder so that nails can be inserted easily overhead, in hard-to-reach locations, or in locations that can't be reached with both hands. The nails are placed on the hammer face, where they are held in position by the magnet and can then be hammered in. The claw of the hammer is excellently suited to pulling out nails, and the point is ideal for moving and aligning heavy timbers, e.g. rafters and purlins. Carpenter s hammer Magnet Art. no. Dimensions (mm) * Weight (g) PU * Total length diyanadimitrova / fotolia.de Product properties Equipped with magnetic nail holder VPA/GS-tested and -certified 163

3 Wall support Provides support during the installation of prefabricated walls Makes the assembly of prefabricated walls significantly easier Thanks to their high load-bearing capacity, the Eurotec wall supports can support walls until they are fully assembled without any problems and therefore take the place of many helping hands. A locking pin system allows especially quick and easy adjustment of the wall support's height. Subsequent fine adjustment is also possible using threaded rods. Wall support galvanised Art. no. Length (mm) Angle of inclination PU max Adjustment range of cm: Basic adjustment via 13 stop positions at intervals of 10,6 cm Fine adjustment with an adjustment range of 19 cm Advantages Universal application Easy operation Fast assembly Almost no force needed from the user Very secure and sturdy Saves time 164

4 Transport anchor system Transport anchor and transport anchor screws The secure lifting system Made of high-grade steel, this lifting attachment is used to lift all kinds of timber parts safely and easily. The transport anchors of the load group up to 1,3 tonnes are strictly to be used only in conjunction with the Ø 11 x 125 mm and Ø 11 x 160 mm Eurotec transport anchor screws. The Eurotec transport anchor screws must only be used once. They are to be screwed into solid wood (softwood), laminated veneer timber, glued laminated timber, cross laminated timber, stacked planks and laminated joists without pilot-drilling. Use in hardwoods is not permitted. The possible, or rather permissible, assembly positions can be found in our operating instructions, of which we will be delighted to provide you with a copy. Please note Transport anchor screws must only be used once Insert the screws without pilot-drilling Read the operating instructions in detail before use Users are to be trained before beginning use for the first time The transport anchor is to be examined for damage before each use and rejected if necessary The weight of the component to be lifted must not exceed the permissible value At least two attachment points per component to be lifted Transport anchor high-quality steel Art. no. Dimensions (mm)* Load group PU** x 70 up to 1,3 tons 2 * Length x width ** Screws must be ordered separately (see below) Transport anchor screw high-quality steel, with AG tip NEW to our product range 11 x 125 mm Permissible lifting load a) per attachment point b) Axial tension Diagonal tension γ c) α d) 11 x 125 mm 11 x 160 mm kg 603 kg kg 462 kg kg 522 kg kg 157 kg a) Calculation according to ETA-11/0024 with wood density ρ k = 350 kg/m³; k mod= 0,9; γ M = 1,3; y G = 1,35; g= 9,81 m/s² and dynamic factor ϕ 2 = 1,16. All mechanical values provided should be viewed as subject to the assumptions that have been made and represent example calculations. All values are calculated minimum values and are subject to typographical and printing errors. b) At least two lines must be used per component to be lifted. Each line leads to exactly one attachment point. If more than two lines are attached, only two attachment points can be assumed to be load-bearing unless it is ensured that the load is distributed evenly onto further lines (e.g. using a compensator) or that the uneven load distribution does not exceed the permissible loading of the individual lines. c) γ - inclination angle of line (chain, rope, lifting strap etc.); at least 60 according to BGR 500 d) α - angle between grain direction and screwing axis Please note: These are planning aids. Projects must only be dimensioned by authorised persons. Art. no. Dimensions (mm) Head PU x 125 SW x 160 SW17 20 AG screw tip Axial tension Diagonal tension 165

5 Japanese saw/folding cutter/-set Tools for every craftsman's toolbox Low force exertion thanks to thin saw blade A Japanese saw is a collapsible handsaw and the counterpart of the precision saws that are common in Europe. The key difference is that Japanese saws only cut on the pull stroke. The especially thin saw blade is a great advantage, along with the associated fine cut, which is achieved with low force exertion. Thanks to the extremely sharp trapezoidal toothing, the cutted timber no longer requires finishing. This saves time and offers attractive results. Folding cutter Supplied with presentation display Advantages Easy handling, fine cuts and flexible saw blade Low force exertion and material wear Saves time Please note The cutting surfaces are very sharp Practise handling before first use to avoid injuries Art. no. Description PU Incl. 5 replacement blades 6 Japanese saw collapsible Folding cutter set Supplied with presentation display NEW to our product range Art. no. Length of saw blade (mm)* Total length (mm)** PU x 35 x 1 530/200 1 Application areas: carpentry crafts, tree care, pruning of trees etc. 166 Spare blade for Japanese Saw Art. no. Dimensions (mm)* PU x 35 x 1 1 * Length x width x thickness, ** Total length / handle length Art. no. Description PU Incl. 5 replacement blades and 1 knife pouch each 6 Advantages Effective blade length 40% greater than with standard cutters Quick-change mechanism Thumb rest Secure blade locking and unlocking Stainless steel housing Blade can be locked in 4 positions Non-slip grip Compatible with standard blades

6 Insulation knife, Ripsaw Universal application for various insulating materials The Eurotec insulation knife stands out in particular thanks to its innovative stainless-steel blade. It differs from conventional insulation knives in its special design and specially ground cutting surface. This ensures that various insulating materials can be cut effortlessly and without tearing, and that the insulation knife does not get stuck. The special knife tip allows you to drill or cut holes into the insulating materials for items that penetrate the insulation. The ergonomic plastic handle has a practical hole for hanging. Insulation knife stainless steel blade Saws timber, timber-based materials and plastic Thanks to its easy handling, the ripsaw from Eurotec can be used as an ideal complement to the electric saws commonly used in timber construction. One clear advantage over classic hand-operated ripsaws is the alternating triple-ground trapezoidal toothing, which allows fine yet rapid cutting with little expenditure of force. With a length of 500 mm, the saw blade cuts only on the pushing stroke and has extra posthardening in the cutting area, delivering a significant reduction in wear. The comfortable handle offers sufficient space for each hand and allows precise handling, as well as optimum force transmission. Ripsaw Universal saw Art. no. Name Blade (mm) PU Insulation knife 340 x 50 1 Art. no. Name Length (mm) PU Ripsaw Universal saw Total length: 480 mm Blade length: 340 mm Blade width: 50 mm Material: blade made of stainless steel, handle made of plastic Advantages Fine cuts, low force exertion Time saving due to high cutting speed Comfortable handle with non-slip rubber inlay Extra posthardening on toothing; less wear Handle with 45 and 90 guides for use as an angle template Please note The cutting surfaces are very sharp Practise handling before first use to avoid injuries Available as a set of 12 units in a presentation display 167

7 Screw clamp An extremely robust screw clamp for professional use The Eurotec screw clamp offers a multitude of useful properties that will be appreciated by professional users in particular. It is extremely robust and provides very user-friendly operation. The clamp also has workpiece-protecting bearing surfaces that ensure the material remains undamaged even if large clamping forces are applied. Screw clamp Art. no. Dimensions a) (mm) PU x x x x x x 95 1 a) Span x projection Advantages Extremely sturdy sliding bar Ergonomic, non-slip twist handle Replaceable and very wide load plates Gentle on the workpiece Comes supplied with one replacement load plate High impact strength Clip-on bearing plates for the sliding bar Guarantees level support on the workpiece and therefore also protection against points of compression 168

8 Scaffold ratchet The must-have tool for scaffolding and stage construction This professional scaffolding ratchet was developed specially for the construction and dismantling of scaffolds of all kinds. It can be used for all common nuts, couplings and special couplings that arise in scaffold construction. This ratchet is a tool for professional users and stands up to the requirements of the scaffold construction industry. High-quality chromium/vanadium steel, a double socket with multiple stages of annealing, and a large switch for the clockwise and anticlockwise directions of rotation make this scaffolding ratchet a must-have tool for scaffold and stage construction. Other key features of this versatile product include a forged shaft and a long service life. Scaffold ratchet Art. no. Opening size PU Art. no. Opening size PU Advantages Made of high-quality chromium/vanadium steel Double socket with multiple stages of annealing Switch for clockwise or anticlockwise rotation Long service life Suitable for a wide range of applications Easy operation Allows flexible working Eléonore H / fotolia.de 169 5

9 Auger bit Eurotec auger bits Eurotec auger bits are ideal for creating deep drill holes and for drill holes with a wide diameter. They can be used both for drilling into end grain and for drilling perpendicular to the grain. The special shape of the conveyor screw ensures a high removal rate and carries the wood chips out of the drill hole without blocking, even in the case of deep drill holes. The centre point with an integrated feed screw prevents the drill from slipping and ensures that it feeds into the material independently even at low speeds. A pre-cutter on the drill point prevents splitting of wood fibres and creates a clean cutting edge. Auger bits are often used to create through holes in beams and rafters, e.g. for construction screws, rafter nails, tapping holes, dowels, etc. Product advantages Precise positioning ensured thanks to spiral-shaped tip Specially shaped transport screw Virtually no expenditure of force required Allows a fast rate of drilling High removal rate Suitable for especially deep drill holes Centre point with integrated feed screw Prevents drill from slipping Feeds into material independently, thereby reducing the effort required Low speeds possible Pre-cutter on drill point No chipping around drill hole Draws itself into the workpiece quickly and without causing splintering No need for finishing work on the cutting edge A hexagonal shaft ensures that the drill is gripped securely in the chuck Ideal for through holes and pilot-drilling Auger bit Art. no. Dimensions (mm) * PU ,0 x ,0 x ,0 x ,0 x ,0 x ,0 x ,0 x ,0 x ,0 x ,0 x ,0 x ,0 x ,0 x ,0 x ,0 x ,0 x ,0 x ,0 x ,0 x ,0 x ,0 x ,0 x ,0 x * Ø x length Auger bit set NEW to our product range 170 Art. no. Dimension/bit (mm) PU ,0 x x x x x x x x 320

10 Hammer tacker This extremely durable and reliable hammer tacker from Eurotec allows maximum impact force for minimum force exertion. The ergonomic grip for fatigue-free working and the spring-back head underline the outstanding quality of this product. We guarantee you simple and rapid handling in a wide range of areas and on all types of wood, e.g. when attaching insulation materials, underlay/housewrap, etc. Hammer tacker NEW to our product range Art. no. Dimensions (cm) Weight (g) PU x 3,7 x 7, Ergonomic soft-touch handle Easy reloading of the magazine Capacity of up to 168 brackets Delivers maximum impact force Hammer tacker brackets And to go with it W L T Art. no. Length (L/mm) Width (W/mm) Thickness (T/mm) PU ,6 1, ,6 1, ,6 1, ,6 1, photo 5000 / fotolia.de 171

11 Protective helmet (EN 397) Perfect protection for work at a height and at ground level NEW to our product range Eurotec protective helmet The Eurotec protective helmet is certified according to EN 397. Its ten ventilation slots provide ideal ventilation but prevent dirt from entering thanks to their net covering. The helmet also features four-point suspension and a preinstalled four-point nylon chinstrap that guarantees a safe and secure fit. Thanks to a control dial system (at the back), the helmet can be adjusted easily to the correct head size (51 62 cm) and therefore offers maximum wearing comfort. Four clips on the outside additionally allow the attachment of external equipment (e.g. a head torch). Advantages and product properties Optimum protection for work at a height and at ground level Control dial system allows adjustment to head size Adjustable head size from 51 to 62 cm Efficient ventilation system thanks to 10 ventilation slots Four-point nylon chinstrap Lightweight and therefore very comfortable to wear Certified according to EN 397 Protection helmet Black Art. no. Head circumference (cm) Total weight (g) PU Protection helmet Pink Quick and easy control dial system for a perfect fit on the head. The ventilation system provides a pleasant cooling effect. Art. no. Head circumference (cm) Total weight (g) PU Protection helmet White 172 Art. no. Head circumference (cm) Total weight (g) PU

12 An unobtrusive slot for attachable ear defenders 1 The ventilation slots provide a pleasant cooling effect 4 The padded lining is made of comfortable nylon 2 The clips allow secure attachment of a head torch 5 Quick and easy control dial system for a perfect fit on the head 173

13 Assembly wedges, adjustment blocks Assembly block With slit Adjustment block With slit Art. no. Dimensions a) (mm) Load-bearing capacity (kg) Height adjustment (mm) Colour PU x 35 x yellow x 38 x white x 43 x grey x 43 x black 364 a) Length x Width x Height Firm grip thanks to special profiled surface Slit allows it to be slid onto nails and screws Serration inside the slit prevents it from slipping off the nail or screw Assembly block Art. no. Dimensions a) (mm) Load-bearing capacity (kg) Colour PU x 50 x blue x 50 x white x 50 x red x 50 x black x 50 x green x 50 x yellow 500 a) Length x Width x Height Slit allows it to be slid onto nails and screws The adjustment blocks can be connected to one another as required Serration inside the slit prevents it from slipping off the nail or screw Adjustment block Closed Art. no. Dimensions a) (mm) Load-bearing capacity (kg) Height adjustment (mm) Colour PU x 28 x red x 43 x grey x 43 x black x 43 x blue 364 a) Length x Width x Height Firm grip thanks to special profiled surface Mini adjustment block With slit Art. no. Dimensions a) (mm) Load-bearing capacity (kg) Colour PU x 50 x red x 50 x green x 50 x blue x 50 x brown x 50 x black x 50 x yellow x 50 x black 250 a) Length x Width x Height High compressive strength Load-bearing capacity of 2 tons When the blocks are stacked, peg and hole connections prevent them from sliding across one another sideways Pegs disappear under loading Art. no. Dimensions a) (mm) Load-bearing capacity (kg) Colour PU x 38 x blue x 38 x white x 38 x red x 38 x black x 38 x green x 38 x yellow 500 a) Length x Width x Height 174 Slit allows it to be slid onto nails and screws Serration inside the slit prevents it from slipping off the nail or screw

14 Ø Mixed box, assembly wedges With and without slit Mixed box, adjustment blocks With slit Hint With our practical mixed boxes, you are equipped for every application. The boxes are available in five different assortments. Art. no. Contents (240 pcs.) PU pcs pcs pcs pcs pcs box Mixed box, assembly wedges With slit Art. no. Contents (250 pcs.) PU pcs. each , , , , & 25 pcs box Mixed box, adjustment blocks Art. no. Contents (100 pcs.) PU pcs. each , box Mixed box, mini adjustment blocks With slit Art. no. Contents (140 pcs.) PU pcs pcs. each , , pcs box Thanks to the transparent transport box and the different colours, you can be sure of finding the right wedge quickly! Art. no. Contents (450 pcs.) PU pcs. each , , , pcs. each , box 175

15 Adjustment block L Art. no. Dimensions a) (mm) Load bearing capacity (kg) Colour PU x 50 x red x 50 x green x 50 x blue x 50 x white x 50 x yellow 100 a) Length x Width x Height Adjustment block XL Art. no. Dimensions a) (mm) Load bearing capacity (kg) Colour PU x 50 x red x 50 x green x 50 x blue x 50 x white x 50 x yellow 100 a) Length x Width x Height Suitable for adjusting the height of stud frames Constructive timber protection when used in lining timber stud frames High compressive strength Load-bearing capacity of 4 tons Two screw holes for fixing in place with screws When the blocks are stacked, peg and hole connections prevent them from sliding across Pegs disappear under loading 176