Why Do We Saw Equipment Types Matching Equipment to the Project Blade Selection Ensuring Construction Quality When Things Don t Go Right The Sawing
|
|
- Elfrieda Philomena George
- 5 years ago
- Views:
Transcription
1
2 Why Do We Saw Equipment Types Matching Equipment to the Project Blade Selection Ensuring Construction Quality When Things Don t Go Right The Sawing Window Summary
3 Controlled Cracking Uncontrolled Cracking
4 Initial Saw Cut Reservoir Cut
5 Wet Saws Two Types Walk Behind Saws Rider Saws/Span Saw Dry Saws (Early Entry) Two Types Walk Behind Saws Rider Saws
6
7 Router
8
9
10 Dry Saws Cleans Seals
11
12 Production Requirements Project Location Construction Logistics and Traffic Control Requirements Available Work Windows Specific Project Requirements (ie dust control) Concrete Aggregate Type Concrete Mix Design
13 Courtesy: MultiQuip
14
15
16
17 Core Segment
18
19
20 Wet Blades 14 to 36 in Diameter RPM based on diameter Down Cut: Keeps Saw Clean in Front by depositing slurry to rear With or W/O Gear box Requires Water for Cooling Dry Blades 6 to 14 in Diameter 3100 to 3500 RPM based on diameter and model Up Cut: Discharges Dust Forward and out of Cut Does Not Require Water- Uses Air Cooling Around Blade Requires Vacuum Dust Collection System
21 What Blade Diameter Can Be Accommodated on Saw What Arbor Size Is Required by Saw What is the Depth of Cut Required Saws Horsepower Affects Diamond Blade Selection Higher Horsepower Saws (i.e. >48 HP) require harder bond or higher diamond concentration More Production in cuts 3 inches or deeper Aggregate Type and Hardness and Concrete Mix Proportions Needed
22 Compressive Strength Hardness of the Aggregate Size of the Aggregate Type of Sand Green or Cured Concrete Abrasiveness of the Aggregate
23 Coarse Aggregate Type: ½ to 2 with ¾ Typical Fine grained hard agg (Mohs 6-9) require softer bonds that wear away faster because higher impact on diamonds Course grained soft agg require abrasive resistant bonds since diamond is subject to less impact Fine Aggregate Type: Sand abrasiveness in green concrete affects bond wear (blade life) the most. The more abrasive the shorter the life. Manufactured or crushed sands are the most abrasive.
24 Admixtures: Materials such as fly ash, which retards the set time, changes the window available to the sawing contractor They also affect the consistency of how well the slab sets up. The sawing contractor does not often know what admixtures were used were.
25
26
27 Begin Sawing 8 to 24 hours after the floating and finishing. Times frames are longer for cold weather. Cut transverse joints first-- most times (should be all of the time) prior to the longitudinal cuts Tracking / wheel alignment on walk behind saws (4 in 40 to the left) -
28
29
30 Unique Blade Up-Cutting Rotations Skid Plate Applying Pressure to the Surface Cut in the Green Zone - First Two Hours- Between Initial Set and Final Set Skid Plate Blade Early Entry Saw Blade Block
31
32
33
34
35 Tabs
36 TRUE EARLY ENTRY SYSTEM From:
37 CC190XL-EE Lifting Hook for Easy Transport Adjustable Handles For Operator Comfort 20.8HP Honda Engine Self-Propelled Drive Max Cutting Depth of 3 With 14 blade Can accept up to.500 wide blades Upcut Design
38 Skid Plates Stainless steel construction 1/8 thick bottom plate allows skid to be used for 2-3 blades before requiring replacement Steel mounting pins that won t break Mounted with a locking pin to keep the plate in place Fits both steel and cast skid plate saws ALWAYS CHECK SKID PLATE BEFORE SAWING! Look for wear at these highlighted areas on the skid plate. If the slot is not longer a straight line, you must replace the skid plate. This wear is typically seen every 2 to 3 blade lives depending on the aggregate type. Offered for blade thicknesses of.125,.250,.375 &.500
39
40
41 Pop Off Doweled Joint Mid Slab Diagonal
42
43
44
45
46
47
48
49 Joint Plow Sealant Removal Sawing
50
51 Ambient air temperature and humidity The type of base that the concrete is placed on Concrete thickness Direct sunlight or shade Blade selection Equipment Saw Cut Depth (T/4) or (T/3)
52
53
54
55
56
57
58
59
60
61 Selection of Appropriate Equipment for the Size and Expected Execution of the Construction Paving is Critical Ensure Safe and Efficient Work Zone Inspect the Work and Verify its Acceptability
62
63
64
65 Thank you
66 Concrete Hardness PSI Critically Hard 8,000 or more Hard 5,000 8,000 Medium 4,000 6,000 Soft 3,000 or less
67
IGGA Guide Specification: Dowel Bar Retrofit (DBR) Introduction
IGGA Guide Specification: Dowel Bar Retrofit (DBR) Introduction This standard developed by the International Grooving and Grinding Association (IGGA) specifies the procedures for construction of dowel
More informationIndustrial Contractors Supplies, Inc.
Industrial Contractors Supplies, Inc. - Dust Director Division - 15061 Route 30, N. Huntingdon, PA 15642 Phone: 412. 824. 6933 Fax: 412. 824. 4704 www.dustdirector.com 5" & 7" SURFACE DUST GUARDS MANUAL
More information4.1. Foremen 4.2. Concrete plant manager 4.3. Concrete plant operator 4.4. Personnel performing saw cutting and joint sealing
10-1. JOINTED PLAIN CONCRETE PAVEMENT GENERAL Summary This work includes constructing jointed plain concrete pavement. Comply with Section 40, "Concrete Pavement," of the Standard Specifications. Submittals
More informationMANHOLES PART I: GENERAL. A. Precast Concrete Manholes
MANHOLES PART I: GENERAL A. Precast Concrete Manholes 1) Manholes shall be made of precast concrete sections of which the top section shall be eccentric or flat slab top. The bottom section shall be a
More informationSOFF-CUT EARLY ENTRY SAWING. Ben Pevreall
SOFF-CUT EARLY ENTRY SAWING Ben Pevreall Manufacturing Footprint - Machines Huskvarna, Swe ~ 100 empl. Xiamen, China ~100 empl. Åsbro, Swe ~ 20 empl. Olathe, KS, USA ~ 50 empl. Manufacturing Footprint
More informationPCCP Preservation Steps to Take to Extend Pavement Life and Performance of Your Concrete Pavements
PCCP Preservation Steps to Take to Extend Pavement Life and Performance of Your Concrete Pavements Larry Scofield, P.E. International Grooving and Grinding Association 1 Big Preservation Everybody Wins
More informationC U T T I N G C R O S S V I L L E P O R C E L A I N S T O N E
C U T T I N G C R O S S V I L L E P O R C E L A I N S T O N E Wet saws are generally used when cutting tile. Crossville uses continuous rim diamond tip blades designed to cut porcelain tile and glass.
More informationDesign and Construction of Highway Pavement Joint Systems
Design and Construction of Highway Pavement Joint Systems Troubleshooting Joint Design and Construction Issues Mark B. Snyder, Ph.D., P.E. Engineering Consultant to the American Concrete Pavement Association
More informationSection 914. JOINT AND WATERPROOFING MATERIALS
914.01 Section 914. JOINT AND WATERPROOFING MATERIALS 914.01. General Requirements. Joint and waterproofing material for use in concrete construction must meet the requirements of this section. 914.02.
More informationCollege of Forestry 610: Power Tools
College of Forestry 610: Power Tools Safety Policy & Procedure Manual Section 600: Workshops and Shop Tools Effective: 01 January 2007 Revised: August 2014 PURPOSE The purpose of this section is to provide
More informationgrinding & polishing 39
grinding & polishing sales@trelawny.co.uk 39 grinding & polishing grinding & polishing - an introduction HOW THEY WORK Floor grinders use a horizontal rotating disc to perform a multitude of tasks, commonly
More informationKANSAS DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION TO THE STANDARD SPECIFICATIONS, 2007 EDITION
Sheet 1 of 7 KANSAS DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION TO THE STANDARD SPECIFICATIONS, 2007 EDITION SECTION 502 PORTLAND CEMENT CONCRETE PAVEMENT (NON-QC/QA) Page 500-20, subsection 502.2.
More informationAMENDMENTS Manual of STANDARD SPECIFICATIONS. Adopted by Standard Specifications Committee. Amendment. No. 6. Published by
AMENDMENTS to 2012 Manual of STANDARD SPECIFICATIONS Adopted by Standard Specifications Committee Amendment No. 6 Published by Utah LTAP Center Utah State University 8305 Old Main Hill Logan UT 84322-8205
More informationDesign and Construction of Highway Pavement Joint Systems
Design and Construction of Highway Pavement Joint Systems Joint Construction Considerations Eric Ferrebee Technical Services Engineer Placing Embedded Steel Embedded Steel Pre-Placed Embedded Steel Fasteners
More informationPRECISION, VERSITALITY, & CONSISTENCY
SMART CUT 6001 GP SECTIONING SAW Operator can change the feed rate and blade speed during operation Can be used for highest precision applications and for general low deformation, low kerf loss sectioning
More informationEZ Saw. New to Existing Dowel Installation System. Specifications and Technical Guide
EZ Saw New to Existing Dowel Installation System Specifications and Technical Guide Custom Mounting Bracket : Custom designed & machined mounting bracket. Adjustable legs for leveling frame on slab. Saw
More informationDouble Bar Plate Dowels for Saw-Cut Contraction Joints
Double Bar Plate Dowels for Saw-Cut Contraction Joints Designed to Deliver More Serviceable Slabs Concrete slabs-on-ground must be able to withstand the repetitious, concentrated loads and abrasion of
More informationProject No.: VTRC 06-R22 March Period Covered: Contract No.
Standard Title Page - Report on State Project Report No. Report Date No. Pages Type Report: Final Project No.: 78783 VTRC 06-R22 March 2006 17 Period Covered: Contract No. Title: Evaluation of Precast
More informationCLASS # 15 ACE DIAMOND BLADES
CLASS # 15 ACE DIAMOND BLADES These blades are manufactured exclusively for Ace Industrial Supply and are available in a wide variety of applications under our own Ace Viper and Eagle Cut brands. They
More informationSession 8: Load Transfer Restoration. (Dowel Bar Retrofit, Cross-Stitching, and Slot Stitching)
Session 8: Load Transfer Restoration (Dowel Bar Retrofit, Cross-Stitching, and Slot Stitching) Learning Outcomes 1. List benefits and applications of dowel bar retrofit (DBR), cross stitching, and slot
More informationFrequently asked questions about our armoured joint with disruptive face technology.
Frequently asked questions about our armoured joint with disruptive face technology. What is disruptive face technology? Traditional armoured joints consist of two parallel faces. As the joint opens, passing
More informationIAMOND ANTAGE PRODUCT CATALOG 12TH EDITION
IAMOND ANTAGE PRODUCT CATALOG 12TH EDITION DIAMOND VANTAGE Since 2003, Diamond Vantage has been serving the construction and stone industries with diamond tools that yield the highest level of performance.
More informationPD 3 Dowel Cradle. Load Transfer System Industrial Slab on Ground
PD 3 Dowel Cradle Industrial Slab on Ground Provides the flattest joints Assists in reducing long term maintenance costs Extends the life-cycle of the floor and the asset Engineered to meet Super Flat
More informationPlate Dowels. An Innovation Driven by Industrial Concrete Paving. Introduction
Plate Dowels An Innovation Driven by Industrial Concrete Paving Introduction Round steel dowel bars have long been the standard load transfer device for concrete pavements with thicknesses of about 8 in.
More informationBY LACKMOND TILE PRODUCTS AND SOLUTIONS EQUIPMENT ACCESSORIES DIAMOND TOOLS
TILE PRODUCTS AND SOLUTIONS EQUIPMENT ACCESSORIES DIAMOND TOOLS BEAST 10" WET TILE SAW BLADE SIZE: MOTOR CAPACITY: RIP CUT CAPACITY: DIAGONAL CUT CAPACITY: DEPTH OF CUT AT 90 : DEPTH OF CUT AT 45 : BEVEL:
More informationTo remove sanding pad, turn counterclockwise.
Disassembly Instructions - Dynorbital EXTREME Models: All Important: Disconnect sander from the air supply. Notice: Use these instructions along with the tool manual. To avoid damage, use the special repair
More informationTRUTH IN VALUE - Industry leader in innovation. - Lowest standard pricing in the industry.
Since 2003, Diamond Vantage has been serving the construction and stone industries with diamond tools that yield the highest level of performance. From its inception, Diamond Vantage has been working to
More informationPOWER TOOL ACCESSORIES
POWER TOOL ACCESSORIES SUPER PREMIUM CHALLENGER SEGMENTED SAW 100% hot press Anti clog bond system High premium treated diamonds Effortless fast cutting Segmented 105 1.8 X 8 20 Super Hard Granite and
More informationDIAMOND BLADE OVERVIEW
DIAMOND BLADE OVERVIEW Variables in Cutting The segment is the part of the blade that actually does the cutting. A measured quantity of manufactured diamonds are mixed together with a specific combination
More informationChapter 26 Abrasive Machining Processes. Materials Processing ABRASIVE MACHINING 10/11/2014. MET Manufacturing Processes
MET 33800 Manufacturing Processes Chapter 26 Abrasive Machining Processes Before you begin: Turn on the sound on your computer. There is audio to accompany this presentation. Materials Processing Chapters
More informationDIAMOND PRODUCTS. Diamond Tools and Equipment Basic Training Booklet
Diamond Tools and Equipment Basic Training Booklet Diamond Products Limited 333 Prospect Street Elyria, Ohio 44035 800-321-5336 www.diamondproducts.com DIAMOND PRODUCTS Part # LIT0009 DIAMOND TOOL BASICS
More informationECONO QUALITY A value quality, entry level grade blade for the extremely cost conscious user Provides good cutting performance at low initial cost Ideal for first time and occasional users PREMIUM QUALITY
More informationAfter continuous casting, the cast products are cut
Flexible deburring grinding solutions for slabs, blooms and billets for continuous production BRAUN has developed a cast product deburring grinding solution, based on its well-proven HP (high-pressure/high-performance)
More informationCONCRETE SAW PARTS LIST
CONCRETE SAW PARTS LIST MODEL CCXL-EE December 01 Part # 1 Intentionally Blank Table of Contents Description Page No. Frame Assembly... Carriage Assembly Motor Assembly.... Blade Shaft Assembly... Spring
More informationBBM 911. Dry drilling machine up to Ø 160 mm. hand guided. Versatile dry drilling machine for drilling up to Ø 160 mm
Dry drilling machine up to Ø 160 mm BBM 911 hand guided ADVANTAGES Sudden stop safety clutch Solid made housing, powder-coated die-cast aluminium for durability Versatile dry drilling machine for drilling
More informationAgricultural Mechanics and Technology Power Tool Safety Rules
Agricultural Mechanics and Technology Power Tool Safety Rules Name: BAND SAW Use: Cutting curves, circles and irregular shapes. 1. Use clean SHARP blades. 2. The teeth should always point DOWN. 3. Adjust
More informationHow to Sharpen a Knife
How to Sharpen a Knife Even a good knife will lose some of its sharpness with time. However, sharpening a knife is easy if you have the right tool and know how to use it. Generally three different materials
More informationOVERVIEW - DUALTREAT GRINDING MACHINES VACUUMS BURNISHERS GRINDING TOOLS. BECO TREAT APS - Nebelvej Horsens (Denmark)
OVERVIEW - DUALTREAT GRINDING MACHINES VACUUMS BURNISHERS LAVINA GRINDING MACHINES X-SERIES L20N-X / L25-X / L30G-X / L32-X LAVINA grinding machines are well known for their long lasting reliability. They
More informationTYROLIT TOOL CHECK. A Company within the SWAROVSKI Group
TYROLIT TOOL CHECK A Company within the SWAROVSKI Group TYROLIT TOOL CHECK - WET CORE DRILLS START 1. TOOL IS NOT DRILLING, DRILLING IS TOO SLOW, DRILL BIT IS CHATTERING 2. LIFETIME OF DRILL BIT IS TOO
More informationExtrusion. Process. The photo below shows a typical thermoplastic extruder.
Extrusion This process can be compared to squeezing toothpaste from a tube. It is a continuous process used to produce both solid and hollow products that have a constant cross-section. E.g. window frames,
More informationSAFETY INFORMATION PACKET
WILLOWCREEK MIDDLE SCHOOL SAFETY INFORMATION PACKET GENERAL SHOP SAFETY 1 WIDE BELT SANDER 2 BAND SAW 3 MITER SAW 4 UP- CUT SAW 4 PLANER 6 TABLE SAW 7 DRILL PRESS 8 LATHE 8 DISK / VERTICAL BELT SANDER
More informationLACKMOND PRODUCTS IS YOUR TRUSTED PARTNER FOR ALL YOUR CUTTING, GRINDING, POLISHING AND DRILLING NEEDS.
LACKMOND PRODUCTS IS YOUR TRUSTED PARTNER FOR ALL YOUR CUTTING, GRINDING, POLISHING AND DRILLING NEEDS. Lackmond Products is pleased to introduce our NEW website which has been redesigned with improved
More informationConquer Diamonds Mfg. Co.since1980 ROMANS 8:37-39
TUCK POINT Premium Laser Welded Segments 4 x 395 x 250 69.00 cd4250ltpp 4 x 395 x 375 90.00 cd4375ltpp 4½ x 395 x 250 78.00 cd4.5250ltpp 4½ x 395 x 375 103.00 cd4.5375ltpp 5 x 395 x 250 86.00 cd5250ltpp
More informationSPECIFICATIONS FOR THE MANUFACTURE AND DESIGN OF PRECAST THREE SIDED ARCH STRUCTURES, WINGWALLS AND HEADWALLS
SPECIFICATIONS FOR THE MANUFACTURE AND DESIGN OF PRECAST THREE SIDED ARCH STRUCTURES, WINGWALLS AND HEADWALLS 1. DESCRIPTION THESE SPECIFICATIONS ARE FOR A PRECAST THREE SIDED ARCH STRUCTURE, HEADWALLS
More informationSECTION MANHOLES
SECTION 33 05 13 MANHOLES PART 1 GENERAL 1.01 SECTION INCLUDES A. CONTRACTOR shall furnish and install precast concrete manhole base, sections, adjusting rings, steps, and manhole ring and cover, complete.
More informationTrouble Shooting Diamond Blade Cutting
Trouble Shooting Diamond Blade Cutting USA $14.95 MKT052409 Contents The Basics 4 Learning Objectives...4 Introduction 4 Concrete Basics 4 Factors Involving Concrete...4 Compressive Strength...5 Hardness
More informationTrade of Metal Fabrication. Module 1: Basic Fabrication Unit 12: Abrasive Grinding and Cutting Phase 2
Trade of Metal Fabrication Module 1: Basic Fabrication Unit 12: Abrasive Grinding and Cutting Phase 2 Table of Contents List of Figures... 4 List of Tables... 5 Document Release History... 6 Module 1
More informationSECTION PRECAST CONCRETE SECTIONAL MANHOLES
SECTION 02545 PRECAST CONCRETE SECTIONAL MANHOLES PART 1 - GENERAL 1.01 SUMMARY A. Section Includes: 1. Precast reinforced concrete cylindrical sectional manholes, complete with openings, inserts, hardware,
More informationGRINDING. quakerchem.com
OVERVIEW Metal removal fluids (MRF) are used for both machining and grinding applications. As was discussed in the basic training, both applications are similar in that there is an interface between the
More informationCORE DRILL, RIG AND BIT SYSTEM
CORE DRILL, RIG AND BIT SYSTEM BCR 130/5BG PROFESSIONAL HANDHELD CORE DRILL Power: 2.6HP/2000W Motor: 115V/60Hz/3-Speed Gearing Bit Range: 3/8" 5-1/8" Wet handheld drilling in concrete: 3/8" 1-1/2" Dry
More informationTools Hand and Power. OSHA Office of Training and Education 1
Tools Hand and Power 1 Hazards Workers using hand and power tools may be exposed to these hazards: objects that fall, fly, are abrasive, or splash harmful dusts, fumes, mists, vapors, and gases frayed
More informationTORLYS LEATHER PLANK INSTALLATION INSTRUCTIONS
ENGLISH INSTRUCTIONS TORLYS LEATHER PLANK INSTALLATION INSTRUCTIONS Dear Customer, You have chosen a high quality TORLYS Leather floor, well suited for all residential application except bathrooms and
More informationHELIX PLANETARY GRINDER M2000 GRINDERS AND POLISHING SYSTEMS. Designed for small jobs and tough-to-reach spaces, this
HELIX PLANETARY GRINDER M2000 GRINDERS AND POLISHING SYSTEMS Designed for small jobs and tough-to-reach spaces, this new coatings. This easy-to-operate machine features an edge grinder, dual speed operation,
More informationB. Installation Instructions. Provide installation instructions, including any special equipment, to address the following.
SAMPLING AND TESTING. The Sampling and Testing requirements contained in -03 shall apply. MARKING. The Marking requirements contained in -03 shall apply. FINAL PRODUCTION INSPECTION. The Final Production
More information18000 HDL FOUR POST LIFT LB CAPACITY INSTALLATION AND OWNER'S MANUAL
18000 HDL FOUR POST LIFT 18000 LB CAPACITY INSTALLATION AND OWNER'S MANUAL WARNING! Do not raise a vehicle unless the front stops are in place, the parking brake is set, and the wheels are chocked. Stay
More informationA H M 531 The Civil Engineering Center
Title Page Introduction 2 Objectives 2 Theory 2 Fitting 3 Turning 5 Shaping and Grinding 7 Milling 8 Conclusion 11 Reference 11 1 Introduction Machining Machining is a manufacturing process in which a
More informationJET Heavy-Duty B3NCH 10" Jobsite Table Saw
JET Heavy-Duty B3NCH 10" Jobsite Table Saw The JET Heavy-Duty 10" Jobsite Table Saw brings many of the capabilities of a full-sized table saw to the jobsite, small or temporary woodworking shops. The unique
More informationBONDED ABRASIVE PRIMER
BONDED ABRASIVE PRIMER Basic information on the terminology and use of bonded abrasive products. Property of: KASCO ABRASIVES Coldwater, Michigan 1-800-367-729 Fax 517-279-7265 1 GENERAL BONDED ABRASIVES
More informationChapter 25. Other Machining Processes. Materials Processing. MET Manufacturing Processes. Shaping Planing Broaching Sawing Filing
MET 33800 Manufacturing Processes Chapter 25 Other Machining Processes Before you begin: Turn on the sound on your computer. There is audio to accompany this presentation. Other Machining Processes Shaping
More informationDiamond Dowel. Load Transfer System INDUSTRIAL SLAB ON GROUND
Diamond Dowel INDUSTRIAL SLAB ON GROUND Diamond Dowel designed for construction joints Tapered plate design allows for diagonal shrinkage Eliminates the need to drill or process formwork Design ensures
More informationGuidelines for working with
Guidelines for working with 1. Sawing Circular Saws When using circular saws, only the circular saw blades that are not set are suitable for cutting PARAPAN. Hardened metal saw blades that have the greatest
More informationManufacturing Processes (continued)
Manufacturing (continued) Machining Some other processes Material compatibilities Process (shape) capabilities Manufacturing costs Correct pg 142, question 34i should read Fig 6.18 question 34j should
More informationSECTION MANHOLES
SECTION 02601 MANHOLES PART 1 GENERAL 1.01 SCOPE OF WORK A. WORK required under this section consists of all materials, accessories, equipment, tools, and labor required to install precast concrete standard
More informationFlanged Dowel Box. Load Transfer System INDUSTRIAL SLAB ON GROUND
Flanged Dowel Box INDUSTRIAL SLAB ON GROUND Designed for construction joints in Post Tension or large shrinkage specifications Large lateral movement and expansion capacity Eliminates the need to drill
More informationConcrete Pavement Preservation
Concrete Pavement Preservation Concrete Pavement Preservation and Preventive Maintenance (A Webinar Series) Part 1 The Essentials: From Pavement Evaluation to Strategy Selection - March 15 Part 2 Partial-
More informationSink BULL INSTRUCTION MANUAL. with Rapid Z -CUT & Rapid Z -DRUM
Sink BULL with Rapid Z -CUT & Rapid Z -DRUM INSTRUCTION MANUAL Please read this instruction manual thoroughly to ensure safety and the correct use of this tool. Keep this manual in a place where operators
More information-_if-;reliminary STUDY IN THE DEVELOPMENT OF A METHOD FOR / EVALUATING THE RELATIVE POLISHING CHARACTERISTICS OF I BITUMINOUS PAVING MIXTURES
-_if-;reliminary STUDY IN THE DEVELOPMENT OF A METHOD FOR / EVALUATING THE RELATIVE POLISHING CHARACTERISTICS OF I BITUMINOUS PAVING MIXTURES by Tom S. Patty Geologist II '{ ~d -- :_ Materials and Tests
More informationDrill Bit Sharpening Attachment. Parts
Parts Base Plate Guide Drill Holder Setting Template Magnifier Instruction Drill Bit Sharpening Attachment With the patented Tormek Drill Bit Sharpening Attachment DBS-22, you can sharpen your drill bits
More informationInitiating Cracks in PCC Pavements. Malcolm K. Lim, PE
Initiating Cracks in PCC Pavements by Malcolm K. Lim, PE Technology Transfer Concrete Consortium (TTCC) and National Concrete Consortium (NCC) Fall 2009, St Louis, MO Better Performance Through Innovative
More informationPRECISION CUTTING MICRACUT 202
PRECISION CUTTING MICRACUT 202 MICRACUT 202 MICRACUT 202 precision cutters are used for precise and deformation-free cutting of Metals, Ceramics, Electronic Components, Crystals, Composites, Biomaterials,
More informationDowel. Design. Performance-Based World of Concrete Official Show Issue. Lift-truck design changes require a new look at joint durability
2007 World of Concrete Official Show Issue January 2007 Performance-Based Dowel Lift-truck design changes require a new look at joint durability Design By Wayne W. Walker and Jerry A. Holland S erviceability
More informationBASIC RECOMMENDATIONS FOR FABRICATING WALKER ZANGER S SECOLO PORCELAIN SLABS
BASIC RECOMMENDATIONS FOR FABRICATING WALKER ZANGER S SECOLO PORCELAIN SLABS CNC Bridge Saw Cutting Parameters: Make certain the porcelain slab is completely supported on the flat, level, stable, and thoroughly
More informationINSTALLATION GUIDELINES: X25 SERIES using perimeter installation fin
INSTALLATION GUIDELINES: X25 SERIES using perimeter installation fin Wall systems designed to manage water or that have been upgraded to manage water are important for a trouble free installation. Site
More information10x12 FOUNDATION GUIDE 10x12 TRICO AND FLORA SHEDS
10x12 FOUNDATION GUIDE 10x12 TRICO AND FLORA SHEDS 10x12 WOOD SKID FLOOR FLOOR SYSTEM FOR 10x12 TRICO AND FLORA SHEDS RAW MATERIALS LIST: 2 (9) FLOOR FRAMING AND SHEATHING: 1) BAND BOARD 2 x 6 x 12 PRESSURE
More informationSima Diamant has inaugurated its new European factory of diamond blades, equipped with stateof-the-art technology on all its manufacturing processes and with the philosophy of producing diamond tools able
More informationJointed Precast Concrete Pavement
NATIONAL PRECAST CONCRETE ASSOCIATION Manual for Jointed Precast Concrete Pavement 3rd Edition Authors Peter Smith, P.E. Mark B. Snyder, Ph.D., P.E. Graphic Designer Deborah Templeton NPCA Precast Concrete
More information110FC STRAIGHT LINE EDGER VICTRALUX 110FC MODEL VICTRALUX 110FC
STRAIGHT LINE EDGER VICTRALUX MODEL STRUCTURE AND MACHINE DESCRIPTION The straight line edger is made up of a pair of shoulders of considerable length (200 mm) connected by a base. The beams have been
More informationTackling America s To- Do List: Project Steps
Tackling America s To- Do List: Installing Shoe Molding Living Room/ Bedroom - Dremel 8200 Rotary Tool - 2500-01 Multi- Vise - 407 Sanding Drum - 430 Sanding Drum (optional) - Wall adhesive - 2500-01 Multi-
More informationChapter M03: Tile Cutting Machines, Saw Benches, Joint Cutters and Vibratory Plates
Maschines and Accessories Chapter : Tile Cutting Machines, Saw Benches, Joint Cutters and Vibratory Plates Cutting Machines Tile Cutting Machines Core Drills Submersible Pumps Saw Benches Vibratory Plates
More informationSPIDA SAW OPERATIONS MANUAL
SPIDA SAW OPERATIONS MANUAL CM SERIAL NUMBER. OCTOBER 2000 CONTENTS Page description 1.) Contents 2.) Safety First 3.) CM Overview 4.) CM Specifications 5.) CM Installation 6.) CM Operation Setting the
More informationPlease read and understand all instructions before beginning. These instructions cover impact and non-impact aluminum French Door 650/750.
The performance and proper operation of a door is only as good as the installation. By following these instructions, the probability of a good installation greatly increases. Please read and understand
More informationSECTION 39 - MANHOLES TABLE OF CONTENTS
SECTION 39 - MANHOLES TABLE OF CONTENTS Section Page 39-1 GENERAL... 39.1 39-2 PRECAST CONCRETE MANHOLES... 39.1 39-2.01 Precast Concrete Sewer Manholes... 39.1 39-2.02 Precast Concrete Storm Drain Manholes...
More informationTable 5G-2.01: Transverse Joint Requirements. Transverse Joint Type 6 C 12 7 C 15 8 CD CD CD 1 20
Design Manual Chapter 5 - Roadway Design 5G - PCC Pavement Joints 5G-2 Types of Joints A. Jointing PCC pavement joints are necessary primarily to control the location of cracks that occur from natural
More informationFlexible Diamond Disc
Diamond Burs - with 2.37mm HP Shanks The abrasive properties of Diamond bonded to the tool ensure fast, easy action & long durability. Used for engraving, drilling, cutting, cleaning castings, etc. Always
More informationLEBANON BOARD OF EDUCATION, LEBANON, CONNECTICUT REQUEST FOR PROPOSALS FOR LYMAN MEMORIAL HIGH SCHOOL BOYS LOCKER ROOM 2/24/2017
LEBANON BOARD OF EDUCATION, LEBANON, CONNECTICUT REQUEST FOR PROPOSALS FOR LYMAN MEMORIAL HIGH SCHOOL BOYS LOCKER ROOM 2/24/2017 The Lebanon Board of Education invites sealed proposals for replacement
More informationStandard Specifications
Standard Specifications PART 1.00 GENERAL 1.01 DECRIPTION SECTION 02620 PRECAST REINFORCED CONCRETE SANITARY MANHOLES A. Work included: The Contractor shall furnish all labor, materials, equipment, and
More information30DC Speed Lathe Manual
30DC Speed Lathe Manual The Crozier Model 30DC Speed Lathe is our most popular model. It has many standard features not found on any other machine in its class or price range. Standard Features 3/4 HP
More informationProduct Catalog. For Distribution Contact Us :
Product Catalog Diamond Polishing Pad Wet Series Ultra D Granite, Engineered Stone, Hard Stone Granite, Engineered Stone, Hard Stone WET Granite Surface Polishing, Granite Edge Polishing, Granite Floor
More informationSubZero Plow System SEVERE INJURY, DEATH, OR EQUIPMENT DAMAGE MAY RESULT IF SAFETY INSTRUCTIONS ARE NOT FOLLOWED.
1 SubZero Plow System Check out our instructional video online at www.rockymountainatvmc.com/videos or on our Youtube channel under: RockyMountainATVMC Safety Instructions For your safety and the safety
More information10. Wing prep and subassembly
Date Section Objective: Construct and fabricate the sub-assemblies of the wing panel. Required Parts: Wing left 11gal PN104-300, Wing right 1gal PN104-400, Wing left 15 gal option PN104-322, Wing right
More informationA full range of abrasive and precision saws, blades, and vices for cutting any material.
A full range of abrasive and precision saws, blades, and vices for cutting any material. SECTIONING Specimen preparation for microstructural examination starts with a quality cut. The proper equipment
More informationPrecast Concrete Pavement Background Concepts. Project 1517 FHWA, CTR & TxDOT Gary Graham November 15, 2001
Precast Concrete Pavement Background Concepts Project 1517 FHWA, CTR & TxDOT Gary Graham November 15, 2001 Project Background CTR contracted by FHWA/TxDOT to investigate the feasibility of using precast
More informationFixed Pitch Wooden Propeller Installation, Maintenance and Inspection Manual
Fixed Pitch Wooden Propeller Installation, Maintenance and Inspection Manual 1 of 8 HPM01 REV. 2 Hercules Propellers Ltd Canal Iron Works Hope Mills Stroud Gloucestershire GL5 2SH United Kingdom +44 (0)
More informationTR53 (IADC 5-3-1) MEDIUM SOFT FORMATIONS
TR52 (IADC 5-2-1) SOFT TO MEDIUM SOFT FORMATIONS AMS TR52 designed for efficient drilling of soft to medium formations such as shale, red bed, limestone and other strata of low compressive strength with
More informationAn Adjustable Threading Feed Attachment for a Lathe Without Metric Threading Capability, by Ted Clarke
An Adjustable Threading Feed Attachment for a Lathe Without Metric Threading Capability by Ted Clarke Metric pitch threads, with the exception of the Royal Microscopical Society (RMS) 36 threads per inch
More informationInstallation Instructions for. Before You Begin TOOLS REQUIRED
Composite Railing System STEP-BY-STEP Installation Instructions for Spectrum Composite Railing Virtually maintenance free 20-year warranty EverNew Spectrum Railing system is designed to work with a number
More informationFor Barrel Tapers. Installation and Operating Instructions for use with table saws and large disk sanders
Tim s Taper Tool For Barrel Tapers Installation and Operating Instructions for use with table saws and large disk sanders Your taper tool is capable of making barrel tapered shafts. The term barrel is
More informationYONGJIA NSV VALVE CO.,LTD. GATE, GLOBE & CHECK VALVES ASSEMBLY & MAINTENANCE PROCEDURES
YONGJIA NSV VALVE CO.,LTD. GATE, GLOBE & CHECK VALVES ASSEMBLY & MAINTENANCE PROCEDURES 1. Features of Construction & Operation GATE VALVE Gate Valve comprises of taper wedge, situated in between two-body
More informationInstallation Instructions for Bifold Doors (JII103)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for premium composite, hollow and solid core molded Bifold Doors. Bifolds are designed for fast
More informationJVI Vector Connector
The JVI Vector Connector User Guidelines 1 of 11 INTRODUCTION JVI designed the Vector Connector for use as shear and alignment connections between precast concrete elements such as double-tee flanges,
More information