Developed by Suzo International. Version 1.3 SERVICE MANUAL

Size: px

Start display at page:

Download "Developed by Suzo International. Version 1.3 SERVICE MANUAL"

Shanon Sheila Robertson
5 years ago
Views:

1 Developed by Suzo International Version. SERVICE MANUAL

2 Nearly years of designing and manufacturing Casino Hoppers has resulted in this new product. Understanding the needs of both casinos and Slot machine manufacturers has led to this extremely durable and World s most service friendly Casino hopper! New features: Service manual Planetary gearbox system provides following advantages: Maximum torque by minimal power consumption. Available in or VDC Silent Operation. Unique bayonet connection for easy and economical motor replacement. Standard optical read out: Indirect optical read out. NPN, normally open (n/o). Optional: Indirect optical read out. NPN, normally closed (n/c). Optional: Second read out in the coin exit. Optics protected by cover against light (fraud) and dust. Other features: Easy accessible coin exit. Steel bearing offer stable disc rotation. Customised frame and cup specifications possible. All wear and tear parts such as pin and shelf wheel are 00% compatible with older generations STC hoppers. Easy to integrate for manufacturers who use older generation STC casino Hoppers. Applicable coin sizes: 8-8mm Optional up to mm. Pay out speed: <mm coins: 0 coins per minute >mm coins: 0 coins per minute All Excel hoppers can be supplied with customised wiring, with choice of strobe pins for low and / or high level detection Control boards: (optional) Part no intelligent control board Vdc with direct start mode, logic Hi start mode, pulse mode and RS serial mode. Part no intelligent control board Vdc with direct start mode, logic Lo start mode, pulse mode and RS serial mode. Part no intelligent control board Vdc with direct start mode, logic Hi start mode, pulse mode and RS serial mode. Part no intelligent control board Vdc with direct start mode, logic Hi start mode, pulse mode and RS serial mode. Part no anti-jam control board Vdc to solve most of the possible coin jams during operation. Periodic maintenance (Warning: Before removing or installing the hopper make sure that power is switched off!) Maintenance recommended in six months interval.. Clean the optical sensor.. Clean the hopper knife and remove all dirt, especially on the route of coins, on the shelf wheel, the pinwheel around the area of the pins and the coin outlet. Inspection, recommended once in a year. Disassembling the coin cup of the hopper, in case of a non-metal cup check for any cracks or brakes.. Inspect the hopper knife for wearing and the correct position! For adjustments see fig.. Inspect the hopper wiper for the correct position. The position of the wiper is very important for a correct payout! If necessary adjust it, see fig.. Inspect the rubber agitator.. Inspect the coin level, check the moment of the switch or check if the coin level probe is securely fastened. 6. Inspect cabling harness for damage, and if necessary tighten cables back on the harness. 7. Assembling coin cup with the screws, springs and bushings back on the wheelhouse. 8. Inspect if the hopper slides gently in and out of the slot machine. Check the hopper and connector for proper function. Warning! Do not use any kind of lubrication on the hopper. After inspection and maintenance check the function of the hopper. For testing using the test mode of the slot- machine. Consult the manual or the slot-manufacturer for further instructions. Power Consumption: Voltage Unloaded Loaded Stall auto reverse VDC 0. Amp 0.0 Amp. Amp VDC 0.0 Amp 0.70 Amp.6 Amp Maximum torque of the motor V - RPM load 6kg N-m V - RPM load kg N-m V - RPM load kg N-m V - RPM load kg N-m Operating temperature: -0 to + 60 C This service manual is intended only to assist the reader in the use of this product. Therefore Suzo international shall not be held liable for any loss or damage whatsoever arising from the use of any information or particulars in or any comission from this manual or any incorrect use of the product.

3 A Adjustments of the excel hopper Adjustment of the hopper with standard knife Loosen the two screws A move the tip of the knife against the pinwheel and the top of the shelfwheel. Lightly hold the knife on the shelfwheel and tighten the two screws A. Rotate the pinwheel and check there is no space between the shelfwheel and the knife in any position. Adjustment of the hopper with full metal knife Loosen the two screws A move the tip of the knife against the pinwheel and the top of the shelfwheel. Turn the pinwheel at least one cycle and tighten the two screws A. Rotate the pinwheel and shelfwheel and the knife in any position. Fig: B C Adjustment of the coin-wiper Position a coin under the wiper, make sure that the top of the wiper is equal to the top of the coin. Slightly loosen the two screws B and C - see fig. Move the wiper edge up to the coin. The edge should be close to the coin, app. 0, mm. Never let the wiper touch the coin! Tighten first the screw B, constantly checking the position of the wiper to the coin. Tighten screw C and check the final position. Do not over-tighten the screws B en C! Fig:

4 Disassembling the hopper.. Remove the screws, which holds the hopper cup to the wheelhousing. Remove the hopper cup and spring which is mounted on the right side of pivot pin.. Remove the hexagon bolts, which holds the wiper, and remove the wiper.. Remove the hexagon bolts, which holds the coin chute, and remove the coin chute and knife.. Remove the Philips screws, which holds the coin deflector, and remove the coin deflector. 6. Remove the Philips screw, and spring in the centre of the disc. The disc assembly is now free floating in the hopper, remove the assembly by pulling on the agitator and lift it from the motor shaft.

5 Remove the hex key screws, and disassemble the whole disc to make the new requested combination. 8. Take requested pinwheel, shelf-wheel and agitator, and mount the screws back in position Put the disc assembly back on the hopper. The disc only fits ways into the driver pin Place the spring liner in position around the disc, make sure the end of the spring liner fits correct in the upper part on the wheelhousing. Finish the reassembling by reversing step,,, and of the disassembling description.

6 6-08-XX Version DRAW. PART DRAW. PART NR. NUMBER DESCRIPTION PCS NR. NUMBER DESCRIPTION PCS -000 PIVOT ROD -007 SCOOP SUPPORT BRACKET 00-9 E WASHER BLACK (DIN 6799) MX0 SCREW PHILL. PAN HD YELLOW -00 SPRING LINER MX8 BOLT HX. HD. TAPT. FL. YELLOW 0 SEE PART LIST G METAL STAR SUPPORT AGITATOR -00 RIGHT SIDE MOUNTING BRACKET SEE PART LIST H CUP LINER 6-00 PIVOT BRACKET M TENSILOCK NUT MX0 BOLT HX. HD. TAPT FL. YELLOW 7-0 EXTENSION SPRING CABLE LOOM AINS COIN BAFFLE MX8 BOLT HX. HD. TAPT FL. YELLOW MEDIUM SCOOP EXTENSION AINS 0-0 CONNECTOR BRACKET AMP PINS LEVELSENSOR PIN -00 LEFT SIDE MTG BRACKET ISOLATION SLEEVE.X7.9X -00 BOTTOM GRIP ISOLATION WASHER 8.XX PLATFORM MM 6-7- TAB 6.MM BRASS HOLE.MM GR -00 SPRING MOUNT HOPPER CUP PCS STANDARD BLUE -0 COMPRESSION SPRING -06 SPRING HEAVY HOPPER CONTROL BOARD 6-00 MOUNT PCB HOLDER M EXT. STAR LOCKWASHER YELLOW SELF ADHESIVE CABLE CLIP 6MM MX SCREW PHILL. PAN HD YELLOW SELF ADHESIVE WIRE CLIP 6XMM MX SCREW PHILL. PAN HD YELLOW INTERF.CABLE FOR PCB HOPPER PROBE MX SCREW PHILL.FLAT HD YELLOW -7* EXCEL WHEELHOUSE ASSEMBLY -0 SPRING LIGHT * SEE LIST -7

7 -7 Version DRAW. PART DRAW. PART NR. NUMBER DESCRIPTION PCS NR. NUMBER DESCRIPTION PCS A - SENSOR COVER 6A MX BOLT HX. HD. YELLOW A MX0 SCREW PH.FL.HD. 7A M NUT HEX. YELLOW A - ROCK AND ROLLER ASSY 8A MX8 SCREW PH. FL. HD. YELLOW A -0 OPTO SENSOR 9A -009 COIN DEFLECTOR A Mx TENSILOCK BOLT YELLOW 0A -08 (PartB) HOPPER KNIFE 6A WIPER A -006 (PartC) OUTLET COVER 7A -06 BEARING PIN A MX6 TENSILOCK BOLT YLLOW 8A -090 BEARING 6X9X6MM A M0X SCREW HX.HD. IMBUS 9A Mx0 FL.HD.MOTOR SCREW A -00 DRIVING HUB 0A MX8 SCREW PH. PAN. HD.YELLOW A -0 (PartD) PINWHEEL PINS A 0- M WASHER.XX0. 6A (PartE) SHELFWHEEL 7MM A - (PartA) MOTOR ASSY RPM-VDC 7A -07 AGITATOR WITH BUSHINGS A -00 EXCEL WHEELHOUSING 8A (PartF) M SCREW HX HD. A MX0 SCREW PH. PAN. HD.YELLOW 9A -06 HUB SPRING A 0-60 M WOODWASHER YELLOW 0A MX0X SCREW PH.HD.FLANGE NICK NR. MIN MAX Part A Part B Part C Part D Part E Part F Part G Part H Part J -XX mm mm motor knife Outlet cov. pinwheel shelfwheel M Screw Met. Supp. cup liner Coin Deflectot not used not used not used not used not used not used not used not used not used not used not used not used not used not used not used

8 Configuration for Euro coins: cent (. mm) Part no. Pinwheel 6 pin for diameter from mm -06 Shelfwheel,mm for coins mm -00- Knife for coins mm (metal insert) -08 Motor VDC RPM - Outlet cover for coins mm cent (9.7 mm) Pinwheel 6 pin for diameter from mm -06 Shelfwheel 6.mm for coins mm Knife for coins mm metal inserts -08 Motor VDC RPM - Outlet cover for coins mm cent (. mm), 0 cent (. mm) and (.mm) Pinwheel pins for diameter from. -.0 mm -0 Shelfwheel 6.mm for coins Knife for coins mm metal inserts -08 Motor VDC RPM - Outlet cover for coins mm -006 (.7 mm) Pinwheel pin for diameter from. -.0 mm -0 Shelfwheel.0mm for coins.9 -.8mm Knife for coins mm metal inserts -08 Motor VDC RPM - Outlet cover for coins mm -006 Configuration for US coins: Nickel (.mm) Pinwheel 6 pin for diameter from 8.0.0mm -06 Shelfwheel, for coin 0..0mm -00- Knife for coins 8.0.0mm metal inserts -08 Motor VDC RPM - Outlet cover for coins mm -006 Quarter (,mm) Pinwheel pin for diameter..0mm -0 Shelfwheel 6, for coin..8mm Knife for coins 8.0.0mm metal inserts -08 Motor VDC RPM - Outlet cover for coins mm -006 Hopper denomination conversions Pinwheels:Part no 6 pin for diameter from mm -06 pin for diameter from. -.0 mm -0 pin for diameter from mm -0 Shelfwheel: 07. mm / coins mm mm / coins mm mm / coins. -.0 mm mm / coins mm mm / coins mm mm / coins mm mm / coins mm mm / coins. -.8 mm mm / coins mm mm / coins mm mm / coins mm Motors: Motor V DC RPM / coins mm -0 Motor V DC RPM / coins mm -0 Motor V DC RPM / coins mm - Motor V DC RPM / coins mm - Coin deflector: Coin deflector -009 Coin deflector coated Knifes: Knife for coins mm -08 Metal knife for coins mm -09 Outlet covers: Outlet cover for coins mm -006 Outlet cover for coins mm Outlet cover for coins mm Cup liners: For standard cup, coins >7.9 mm -0 For wide and narrow cup, coins >7.9mm Agitator: Standard rubber agitator -07 Dollar token (7.mm) Pinwheel pin for diameter from 8.0.0mm -0 Shelfwheel 07, for coin mm Metal Knife for coins 8 8mm -09 Motor VDC RPM - Outlet cover for coins.> Cup liner for standard cup, used for coins >7.9mm -0 Cup liner for wide and narrow cup, used for coin >7.9mm -08 Metal star on agitator for coins >.mm -080 This document is the private property of Suzo international and may not be reproduced in part or in total by means, electronic or otherwise without the written permission of Suzo international. Suzo International does not accept any errors contained in this document. 7

9 6 D D 6 8 C C B B 6 Suzo International (NL) BV A Antonie van Leeuwenhoekstraat 9 A 6 LT Oud Beijerland Tel. + (0)86-6 Fax. + (0)86-6 info@suzo.com Description: Excel Hopper Standaard Date: Partnumber: Revision: Size: A

10 6 D D 8 0 C C B B 6 0 Suzo International (NL) BV A Antonie van Leeuwenhoekstraat 9 A 6 LT Oud Beijerland Tel. + (0)86-6 Fax. + (0)86-6 info@suzo.com Description: Excel Hopper Narrow cup Date: Partnumber: Revision: Size: A

6 D D 8 C C 9 B 8 87 B 0 0 6 9 8 66 A Suzo International (NL) BV Antonie van Leeuwenhoekstraat 6 LT Oud Beijerland Tel.

11 6 D D 8 C C 9 B 8 87 B A Suzo International (NL) BV Antonie van Leeuwenhoekstraat 6 LT Oud Beijerland Tel. + (0)86-6 Fax. + (0)86-6 info@suzo.com 9 A Description: Excel Hopper Medium cup Date: Partnumber: Revision: Size: A 6

12 6 D D 6 8 C C B B Suzo International (NL) BV A Antonie van Leeuwenhoekstraat 9 A 6 LT Oud Beijerland Tel. + (0)86-6 Fax. + (0)86-6 info@suzo.com Description: Excel Hopper Extended cup Date: Partnumber: Revision: Size: A

13 6 D D 6 8 C C B B Suzo International (NL) BV A Antonie van Leeuwenhoekstraat 9 A 6 LT Oud Beijerland Tel. + (0)86-6 Fax. + (0)86-6 info@suzo.com Description: Excel Hopper Wide cup Date: Partnumber: Revision: Size: A

SERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12" SLIDING COMPOUND MITER SAW

SERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12 SLIDING COMPOUND MITER SAW PAGE 1 OF 6 BASE ASSEMBLY 00 0 CATALOG NO. EXAMPLE: SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS 6955-20 1 02-80-0050 Thrust Bearing (1) 2 05-80-0510 M5 x 12mm Flat Head T-20 Screw (5) 3 05-81-0135