ceramic saw dielectric

Transcription

1 K55N N9D ceramic saw dielectric 915 g 197g K55N N9D 197 g K55N N9D

2 Table of Contents eneral Description Ceramic Filters - KHz Band Leaded Standard KBF Series Low Profile KBF Series... 5 Surface Mount PBFS Series-4 element... 6 PBFC Series-4 element... 7 PBFC Series-6 element... 8 PBF Series Packaging and Solder Pad Layout... 9 Surface Acoustic Wave Filters eneral Description... 1 Leaded Broadcast Satellite/CATV Converter - KAF Series /49 MHz Cordless Phone - KAF Series Surface Mount PAFC Series Dielectric Filters Surface Mount KDF Series PDFB Series PHS/DECT - PDFB Series EMI Noise Filters

3 AVX/KYOCERA Ceramic Filters K55N N9D 197 g 197g K55N N9D eneral Description AVX/KYOCERA s sophisticated ceramics technology has greatly increased selectivity and wide-band characteristics, and has stabilized the characteristics of ceramic filters. The series covers a wide range of attenuation and bandwidths to allow selection of the most optimum filter characteristics for each application. AVX/KYOCERA filters are bandpass filters consisting of one or more ceramic resonators connected in a ladder network configuration. Passband characteristics are determined by the relative resonant and anti-resonant frequencies of the resonators. Both narrow and wide passband configurations are manufactured by adjusting the resonator frequency characteristics. This is illustrated in figure 2 for a single ladder. The difference between the resonance frequency of the series resonator and the anti-resonance frequency of the parallel resonator determines the bandwidth of the ceramic filter (figure 3). Attenuation is determined by the ratio of the equivalent circuit parallel capacitors (Cp/Cs) for the resonators. The higher capacitance value for the parallel resonator can be obtained by using a thinner dielectric than for the series resonator. This maintains relative tracking of capacitance values over the operating temperature range and assures excellent temperature characteristics for the ceramic filter. Input and output impedance should be matched closely to the values listed for each ceramic filter. Incorrect impedance matching could result in shifts of the center frequency and increase ripple over those specified. The terminology used to describe the performance of ceramic filters is illustrated in figure 1. All attenuation measurements are referenced to the insertion loss ratio of input and output. This will be between 4 and 6dB maximum. The passband width is measured at 6dB below the reference insertion loss level. For larger ladders, it is also defined at 4 or 5dB for 4- or 6-element filters respectively. The frequency at the center of the passband width is called the center frequency. It may not be the frequency of minimum loss. Variations in the passband region below the insertion loss level is called ripple and is expressed in db s. The points of detuning (maximum attenuation) around the center frequency are called the stop band attenuation or selectivity. Spurious response is an expression relating to the minimum attenuation of unwanted frequencies in the stop band region referenced to the insertion loss or minimum attenuation in the passband range. roup delay time is an expression for the distortion of linearity in the phase angle over the frequencies in the passband region. It is determined by the slope of the phase shift between input and output differentiated by the passband frequencies. Ceramic filters exhibit aussian filter type characteristics and special roup Delay control is available in 4-element AVX/KYOCERA filters. 1

4 AVX/KYOCERA Ceramic Filters INSERTION LOSS khz Band Filter RIPPLE THROUH LEVEL 6dB 1 S T O P S T O P A TT E N U AT I O N (db) 2 3 4dB 4 5dB 5 B A N D A T T E N U A T I O N 6dB Band Width Lower 4dB Band Width Lower 5dB Band Width Lower 6dB Band Width Upper 4dB Band Width Upper 5dB Band Width Upper ROUP DELAY TIME B A N D A T T E N U A T I O N R O U P D EL A Y T I M E 6 7 ƒo (CENTER FREQ.) POLE BAND WIDTH FREQUENCY (khz) Fig. 1 Series Resonator Equivalent Circuit L O C O R O input output Impedance (Z) C S L I Parallel Resonator Equivalent Circuit fo C P C I Attenuation (db) R I ground ground frequency Fig. 2 Fig. 3 2

5 khz Band Ceramic Filters KBF Series Features 1) Compact, with high selectivity 2) Low insertion loss 3) Adjustment-free 4) Wide choice of passbands How To Order KBF R - 2 A Model (Kyocera Bulk Filter) 2 Center frequency 45 45kHz kHz 5 A AS High selectivity type Ultra high selectivity type 3 Number of ceramic elements Marking R P 6-element 4-element Passband width (at 6dB) # Elements Total Bandwidth, khz 6-element 2, 15, 12, 1, 9, 7, 6, 4 4-element 25, 2, 15, 12, 1, 9, 7, 6, 4 1 Passband width (at 6dB) 2 Manufacturing monthly code 3 Case color Blue KBF-455P/R Series reen KBF-45P/R Series Dimensions KBF-R series (6-element) KBF-P series (4-element) 11. (.433) Marking 7. (.276) 8. (.315) Marking 7. (.276) 8.4 (.331).2 (.8) 4. (.157).8 (.31).6 (.24) 4.3 (.169) 8. (.315).15 (.6) 4. (.157).8 (.31).6 (.24) 1.1 (.43) 5 3. (.118) (.114) (.16) 7. (.276) 1.2 (.47) 1. INPUT 2. OUTPUT 3. ROUND 4. ROUND 5. ROUND 4.3 (.169).8 (.31) (.16) 7. (.276) 1.2 (.47) 1. INPUT 2. OUTPUT 3. ROUND Unit: mm (inch) Test Circuits KBF-R series (6-element) KBF-R 2 R KBF-P series (4-element) R1 KBF-P Rg S.S. R2 C R V Rg S.S. R2 C RF VM R1 + Rg = R2 = Input/output impedance rating C 5pF (Including tool strays, wiring capacitance and RF V. M. input capacitance) R1 + Rg = R2 = Input/output impedance rating C 5pF (Including tool strays, wiring capacitance and RF V. M. input capacitance) 3

6 khz Band Ceramic Filters KBF Series Specifications (KBF-455 Series) R (6-element) type Center Bandwidth Stop Band Insertion Input/output Operating roup Delay Part No. Ripple Frequency (fo) 6dB 5dB Attenuation Loss Impedance Temp. Range Time 3 µsec. max. KBF-455R-3K ±15.kHz min. ±3.kHz max. (455±1kHz) 4dB min. 3 µsec. max. KBF-455R-25K ±12.5kHz min. ±25.kHz max. 4dB max. (455±8kHz) 1.5kΩ KBF-455R-2A ±1.kHz min. ±2.kHz max. KBF-455R-15A 455kHz±1.5kHz ±7.5kHz min. ±15.kHz max.. KBF-455R-12A ±6.kHz min. ±12.5kHz max. -2 C 2.dB min. 37dB min KBF-455R-1A ±5.kHz min. ±12.kHz max. to +8 C KBF-455R-9A ±4.5kHz min. ±1.kHz max. 6dB max. 2.kΩ KBF-455R-7A ±3.5kHz min. ±9.kHz max. KBF-455R- 6AS 455kHz±1.kHz ±3.kHz min. ±9.kHz max. 55dB min. KBF-455R- 4AS ±2.kHz min. ±7.5kHz max. P (4-element) type Center Bandwidth Stop Band Insertion Input/output Operating roup Delay Part No. Ripple Frequency (fo) 6dB 4dB Attenuation Loss Impedance Temp. Range Time 3 µsec. max. KBF-455P-3K ±15.kHz min. ±35.kHz max. (455±1kHz). 3 µsec. max. KBF-455P-25K ±12.5kHz min. ±3.kHz max. 4dB max. (455±8kHz) KBF-455P-25A ±12.5kHz min. ±24.kHz max. 1.5kΩ KBF-455P-2A ±1.kHz min. ±2.kHz max. 455kHz±1.5kHz KBF-455P-15A ±7.5kHz min. ±15.kHz max. 27dB min. KBF-455P-12A 2.dB max. ±6.kHz min. ±12.5kHz max. -2 C to +8 C KBF-455P-1A ±5.kHz min. ±11.kHz max. 6dB max. KBF-455P-9A ±4.5kHz min. ±1.kHz max. KBF-455P-7A ±3.5kHz min. ±9.kHz max. 2.kΩ KBF-455P-6AS 455kHz±1.kHz ±3.kHz min. ±9.kHz max. 35dB min. KBF-455P-4AS ±2.kHz min. ±7.5kHz max. Specifications (KBF-45 Series) R (6-element) type Center Bandwidth Stop Band Insertion Input/output Operating roup Delay Part No. Frequency (fo) Ripple 6dB 5dB Attenuation Loss Impedance Temp. Range Time 3 µsec. max. KBF-45R-3K ±15.kHz min. ±3.kHz max. (455±1kHz) 4dB min. 3 µsec. max. KBF-45R-25K ±12.5kHz min. ±25.kHz max. 4dB max. (455±8kHz) 1.5kΩ KBF-45R-2A ±1.kHz min. ±2.kHz max. KBF-45R-15A 45kHz±1.5kHz ±7.5kHz min. ±15.kHz max. KBF-45R-12A ±6.kHz min. ±12.5kHz max. -2 C 2.dB min. 37dB min. KBF-45R-1A ±5.kHz min. ±12.kHz max. to +8 C KBF-45R-9A ±4.5kHz min. ±1.kHz max. 6dB max. 2.kΩ KBF-45R-7A ±3.5kHz min. ±9.kHz max. KBF-45R- 6AS 45kHz±1.kHz ±3.kHz min. ±9.kHz max. 55dB min. KBF-45R- 4AS ±2.kHz min. ±7.5kHz max. P (4-element) type Center Bandwidth Stop Band Insertion Input/output Operating roup Delay Part No. Ripple Frequency (fo) 6dB 4dB Attenuation Loss Impedance Temp. Range Time 3 µsec. max. KBF-45P-3K ±15.kHz min. ±35.kHz max. (455±1kHz). 3 µsec. max. KBF-45P-25K ±12.5kHz min. ±3.kHz max. 4dB max. (455±8kHz) KBF-45P-25A ±12.5kHz min. ±24.kHz max. 1.5kΩ KBF-45P-2A ±1.kHz min. ±2.kHz max. 45kHz±1.5kHz KBF-45P-15A ±7.5kHz min. ±15.kHz max. 27dB min. -2 C KBF-45P-12A 2.dB max. ±6.kHz min. ±12.5kHz max. to +8 C KBF-45P-1A ±5.kHz min. ±11.kHz max. 6dB max. KBF-45P-9A ±4.5kHz min. ±1.kHz max. KBF-45P-7A ±3.5kHz min. ±9.kHz max. 2.kΩ KBF-45P-6AS 45kHz±1.kHz ±3.kHz min. ±9.kHz max. 35dB min. KBF-45P-4AS ±2.kHz min. ±7.5kHz max. 4

7 Low Profile khz Band Ceramic Filters KBF Series Features 1) Low profile package 2) Compact, high selectivity 3) Low insertion loss 4) Adjustment free 5) Wide choice of passbands Test Circuit Rg R S.S. Filter Output Input round R1 R1 + Rg = R2 = Input/output impedance rating C < 5pF (Including stray capacitance and input capacitance) C RF VM How to Order KBF RS - 2 A C Model (Kyocera Bulk Filter) 2 Center frequency 45 45kHz kHz 3 Number of ceramic elements RS 6-element PS 4-element 4 Passband width (at 6dB) # Elements Total Bandwidth, khz 6-element 3, 25, 2, 15, 12, 1, 9, 7, 6, element 3, 25, 2, 15, 12, 1, 9, 7, 6, 4 A AS Blank C High selectivity type Ultra high selectivity type Standard lead length 3.5mm Short lead 2.2mm Dimensions KBF-RS Series (6-element) 6.4 (.252) Passband width 9.5 (.374) Month date code Standard Leads 6.3 (.248) 3.5 (.138).6 (.24) Short Leads.4 (.16) (.16).4.6 (.24) 4.3 (.169) (.35) (.94)(.12)(.114) (.35) 1. Input 2. Output 3. round 4. round 5. round 6.4 (.252) Passband width 2.2 (.87) 6.5 (.256) Month date code Standard Leads KBF-PS Series (4-element) 3.5 (.138) 6.3 (.248) 3.5 (.138).6 (.24) Short Leads.4.4 (.16) (.16).6 (.24) 4.3 (.169) (.75) 4.3 (.169) 1. Input 2. round 3. Output 4. round.7 (.28) 1.6 (.63) 3.5 (.138) 2.2 (.87).4 (.16).4 (.16).4 (.16).4 (.16) Unit: mm (inches) Specifications 455kHz (45kHz available with same specifications) KBF-RS Series (6 elements) Center Passband Width Input/Output Stop Band Insertion Part No. Operating Frequency (fo) Ripple Attenuation Loss Matching Temperature 6dB 5dB Impedance KBF-455RS-3K ±15.kHz min. ±3.kHz max. KBF-455RS-25K ±12.5kHz min. ±25.kHz max. 4dB min. 4dB max. 1.5kΩ KBF-455RS-2A ±1.kHz min. ±2.kHz max. KBF-455RS-15A 455kHz±1.5kHz ±7.5kHz min. ±15.kHz max. KBF-455RS-12A 2.dB max. ±6.kHz min. ±12.5kHz max. -2 C 37dB min. KBF-455RS-1A ±5.kHz min. ±12.kHz max. to +8 C KBF-455RS-9A ±4.5kHz min. ±1.kHz max. 6dB max. KBF-455RS-7A ±3.5kHz min. ±9.kHz max. 2.kΩ KBF-455RS-6AS 455kHz±1.kHz ±3.kHz min. ±9.kHz max. KBF-455RS-4AS ±2.kHz min. ±7.5kHz max. 55dB min. KBF-PS Series (4 elements) Center Passband Width Input/Output Stop Band Insertion Operating Part No. Frequency (fo) Ripple Attenuation Loss Matching Temperature 6dB 5dB Impedance KBF-455PS-3K ±15.kHz min. ±35.kHz max. KBF-455PS-25K ±12.5kHz min. ±3.kHz max. 4dB max. 1.5kΩ KBF-455PS-25A ±12.5kHz min. ±24.kHz max. KBF-455PS-2A 455kHz±1.5kHz ±1.kHz min. ±2.kHz max. 27dB min. KBF-455PS-15A 2.dB max. ±7.5kHz min. ±15.kHz max.. -2 C KBF-455PS-12A ±6.kHz min. ±12.5kHz max. to +8 C KBF-455PS-1A ±5.kHz min. ±12.kHz max. 6dB max. KBF-455PS-7A ±3.5kHz min. ±9.kHz max. 2.kΩ KBF-455PS-6AS 455kHz±1.kHz ±3.kHz min. ±9.kHz max. KBF-455PS-4AS ±2.kHz min. ±7.5kHz max. 35dB min. 5 roup Delay Time 3 µsec. max. (455±1kHz) 3 µsec. max. (455±8kHz) roup Delay Time 3 µsec. max. (455±1kHz) 3 µsec. max. (455±8kHz)

8 Surface Mount khz Band Ceramic Filters PBFS Series Features 1) Small and low profile 2) Excellent anti-shock performance 3) Reflow solder compatible 4) Taped for automatic placement How to Order PBFS 455 P 15 D R K55N N9D K55N N9D 1 Model: PBFS 2 Center frequency 45 45kHz kHz Test Circuit 3 Number of ceramic elements P 4-element 4 Passband width (at 6dB) # Elements Total Bandwidth, khz 4-element 3, 25, 2, 15, 12, 9, 6, 4 5 roup Delay Time Available Bandwidth, khz D Standard roup Delay 2, 15, 12, 9, 6, 4 K Controlled roup Delay 3, 25, 2 6 Packaging: R=Tape and reel (1, pcs. per reel) S.S.. (Standard Signal enerator) Rg R1 R2 R1+Rg=R2=input/output impedance rating C 5pF (including tool strays, wiring capacitance and RFVM input capacitance) C R.F.V.M. (Radio Frequency Voltage Meter) Dimensions Reflow Profile (1) Input (2) nd (3) Output (1) (2) (3) ±.1 1.±.1 1.± ±.1 1. Units: mm Tolerance: ±.3 unless shown otherwise 4. 3 Temp. ( C) Pre-Heating 23 C 6 sec. 6 sec. 2 sec. MAX Time Specifications (45kHz available with same characteristics) Part No. Center roup Passband Width Input/Output Frequency Insertion Operating Ripple Delay Attenuation Matching (fo) Loss Temperature Time 6dB 4dB Impedance PBFS455P2D ±1.kHz min. ±2.kHz max. PBFS455P15D 455kHz ±7.5kHz min. ±15.kHz max. PBFS455P12D ±1.5kHz ±6.kHz min. ±12.5kHz max. 1.5kΩ 2dB max. PBFS455P9D ±4.5kHz min. ±11.kHz max. -2 C PBFS455P6D 455kHz ±3.kHz min. ±9.kHz max. 25dB min. 6dB max. PBFS455P4D ±1.kHz ±2.kHz min. ±7.5kHz max. to +8 C 15µSec max. at 455kHz PBFS455P3K ±1kHz ±15.kHz min. ±35.kHz max. 455kHz 15µSec max. at 455kHz PBFS455P25K ±1.5kHz 1dB max. ±8kHz ±12.5kHz min. ±3.kHz max. 1.kΩ 3µSec max. at 455kHz PBFS455P2K ±7kHz ±1.kHz min. ±25.kHz max. 6

9 Surface Mount khz Band Ceramic Filters PBFC Series Features 1) Small and low profile 2) Excellent anti-shock performance 3) Reflow solder compatible 4) Taped for automatic placement How to Order PBFC 455 P 15 D R K55N N9D K55N N9D 1 Model: PBFC 2 Center frequency 45 45kHz kHz 3 Number of ceramic elements P 4-element 4 Passband width (at 6dB) # Elements Total Bandwidth, khz 4-element 3, 25, 2, 15, 12, 9, 6, 4 5 roup Delay Time Available Bandwidth, khz D Standard roup Delay 2, 15, 12, 9, 6, 4 K Controlled roup Delay 3, 25, 2 6 Packaging: R=Tape and reel (1, pcs. per reel) Dimensions Test Circuit S.S.. (Standard Signal enerator) Rg R1 Reflow Profile R2 R1+Rg=R2=input/output impedance rating C 5pF (including tool strays, wiring capacitance and RFVM input capacitance) C R.F.V.M. (Radio Frequency Voltage Meter) Temp. ( C) 25 Pre-Heating 23 C (1) Input (2) nd (3) Output (3) (2) (1) Time Units:mm Tolerance: ±.3 unless shown otherwise 6 sec. 6 sec. 2 sec. MAX Specifications (45kHz available with same characteristics) Part No. Center roup Passband Width Input/Output Frequency Insertion Operating Ripple Delay Attenuation Matching Loss Temperature (fo) Time 6dB 4dB Impedance PBFC455P2D ±1.kHz min. ±2.kHz max. PBFC455P15D 455kHz ±7.5kHz min. ±15.kHz max. PBFC455P12D ±1.5kHz ±6.kHz min. ±12.5kHz max. 1.5kΩ 2dB max. PBFC455P9D ±4.5kHz min. ±11.kHz max. -2 C PBFC455P6D 455kHz ±3.kHz min. ±9.kHz max. 25dB min. 6dB max. to +8 C PBFC455P4D ±1.kHz ±2.kHz min. ±7.5kHz max. 15µSec PBFC455P3K ±15.kHz min. ±35.kHz max. 455kHz max. at 455kHz 15µSec max. at 455kHz PBFC455P25K 1dB max. ±8kHz ±12.5kHz min. ±3.kHz max. ±1.5kHz 1.kΩ 3µSec max. at 455kHz PBFC455P2K ±7kHz ±1.kHz min. ±25.kHz max. 7

10 Surface Mount khz Band Ceramic Filters PBFC Series Features 1) Small and low profile 2) Excellent anti-shock performance 3) High selectivity How to Order PBFC 455 R 25 K R Model: PBFC 2 Center frequency 45 45kHz kHz 3 Number of ceramic elements R 6-element Test Circuit R1 Filter Output round R2 4 Passband width (at 6dB) # Elements Total Bandwidth, khz 6-element 3, 25, 2, 15, 9 Rg S.S.. C R.F. V.M. Rin 5 roup Delay Time Available Bandwith, khz D Standard roup Delay 2, 15, 9 K Controlled roup Delay 3, 25, 2 R1+Rg=R2+Rin=Rating impedance input/output matching C<5pF (including stray capacitance and input capacitance) 6 Packaging: R=Tape and reel (1, pcs. per reel) Dimensions Reflow Profile 7.5 max. Temp. ( C) K K C min. 15 sec. max. Peak Temp. 23 C±5 C (3) (4) (1) (2) 3. max. Pin 1 Input 2 round 3 Output 4 round (Unit: mm) C min. 4 sec. max. Specifications (45kHz available with same characteristics) Part No. Center Passband Width Input/Output Stop Band Insertion roup Frequency Ripple Matching (fo) 6dB 4dB Attenuation Loss Impedance Characteristics PBFC455R9D ±4.5kHz min. ±11.kHz max. PBFC455R15D 455kHz±1.5kHz 2.dB max. ±7.5kHz min. ±15.kHz max. 4dB min. 1.5kΩ PBFC455R2D ±1.kHz min. ±2.kHz max. PBFC455R2K ±1.kHz min. ±25.kHz max. 47dB min. PBFC455R25K 455kHz 1.dB max. ±12.5kHz min. ±3.kHz max. PBFC455R3K ±14.kHz min. ±35.kHz max. 5dB min. * Option 8 6.dB max. 1.kΩ (1.5kΩ)* 3. µsec. max. (455±7.kHz) 3. µsec. max. (455±8.kHz) 3. µsec. max. (455±1.kHz)

11 Surface Mount khz Band Ceramic Filters PBF Series Tape and Reel Dimensions Suggested Solder Pad Layout PBFS-P Series (4-element) PBFS-P Series (4-element) 2. ±.1 φ ±.1 4. ± ± ± ± ± ± ±.2 7. ± ± ± ±.2 Units:mm Units:mm PBFC-P Series (4-element) PBFC-P Series (4-element) 2. ±.1 φ ±.1 4. ± ± ± ± ± ± ± ± ± ± ±.2 Units:mm 1.5 Units:mm PBFC-R Series (6-element) PBFC-R Series (6-element) ± φ ±.1.5 ± max max max max. Units:mm Units:mm Reel Dimensions PBFS/PBFC 4-element PBFC 6-element 2. ±.2 33 ±1.5 8 ±1. 33 ±1.5 8 ±1. 13 ± ± ±2.5 1, pieces per reel 9

12 AVX/Kyocera Surface Acoustic Wave Filters eneral Description Surface acoustic wave (SAW) filters are electroacoustic bandpass filters which operate via delay paths that add (passband) and cancel (stopband) frequencies. Surface waves are generated when RF signals are applied to electrodes on a piezoelectric substrate such as PZT piezo material. The amplitude and phase can be controlled by the distance between and overlap of the electrodes. A typical SAW filter is shown in figure 1. Input is through the interdigital electrode transducer which generates a surface acoustic wave in the piezoelectric substrate. This wave travels to the output interdigital electrode transducer where it is reconverted to a voltage output. The direction of the wave is controlled by damping material which absorbs and prevents scattering of the wave. SAW filters exhibit higher insertion loss than LC filters, 2-3 db. Their prime feature is their flat passband characteristics (low ripple) coupled with a constant roup Delay Time (low distortion). This is obtained by the independent design parameters for phase and amplitude characteristics. SAW filters are also small size, rugged, reliable and low cost. 13N A A: 49 N A A: AVX/KYOCERA SAW filters are available hermetically sealed in TO type cans to prevent moisture condensation on the surface of the device. They are available in the frequency range from 3 to 15 MHz and find wide application in TV, VCR, CATV, satellite receivers and cordless telephones. ABSORBER PIEZOELECTRIC SUBSTRATE ABSORBER R S R L INPUT SINAL INPUT IDT SHIELDIN OUTPUT IDT Figure 1 1

13 SAW Filters - Broadcast Satellite/CATV Converter KAF Series Features 1) Compact 2) Adjustment free 3) High reliability How To Order KAF NR-MB Model (Kyocera Acoustic Filter) 2 Frequency 3 Type Dimensions Test Circuit ø.78 (.31) 2.5 (.98) (.197) (.177) 1. INPUT 2. ROUND 3. OUTPUT 4. OUTPUT 5. ROUND 5Ω 25Ω Ω S 5Ω R.F. V.M (.197) 12. (.472) Unit: mm (inch) (BOTTOM VIEW) Specifications Insertion Center Bandwidth Bandwidth Passband roup Delay Spurious Temp. Coef. Part No. Loss Frequency at 3dB at 3dB Ripple Ripple Response of Frequency (db) (MHz) (MHz) (MHz) (db) (nsec) (db) (ppm/ C) KAF-134NR-MB 25 max min. 5 max. KAF-13NR-MA 22 max. 22 min. 45 max. ±1 35 min. 13 KAF-13NR-MB 21 max. 26 min. 5 max. -8 max 1. max. KAF-7NR-WC 32 max min. 3 max. ±2 KAF-7NR-WD 33 max min. 34 max. ±3 3 min. (1 to 1MHz) 25 min. (1 to 1MHz) 11

14 SAW Filters - 46/49 MHz Cordless Phone KAF Series Features 1) Adjustment free 2) High reliability 3) Low insertion loss How To Order KAF - 46 NR-ME Model (Kyocera Acoustic Filter) 2 Frequency 3 Type number Dimensions Test Circuit KAF-46 NR-ME/KAF-49NR-MA ø.78 (.31) (.98) (.197) (.177) 1. OUTPUT 2. ROUND 3. OUTPUT 4. INPUT 5. ROUND L1 (µh) L2 (µh) Ω L1 S 3 4 L Ω R.F. V.M (.197) 12. (.472) Unit: mm (inch) (BOTTOM VIEW) (BOTTOM VIEW) Specifications Part No. Attenuation (46.61 ~ 46.97MHz) Attenuation (49.67 ~ 49.99MHz) KAF-46NR-ME 6. db max. 3 db min. KAF-49NR-MA 3 db min. 6. db max. Characteristics Att.(dB) Att.(dB) KAF-46NR-ME Freq. (MHz) KAF-49NR-MA Freq. (MHz) Att.(dB) Att.(dB) Freq. (MHz) Freq. (MHz) 12

15 Surface Mount SAW Filters - PHS PAFC Series Features 1) Small and low profile 2) Flat passband characteristics 3) Low insertion loss 4) Circuit simplification Application 1) PHS How To Order PAFC 248 A Series 2 Center frequency 3 Type F248 F248 Shape and Dimension Recommended Land Pattern IN Specifications Test Circuit 1.6 Part Number PAFC248A PAFC243A Nominal Center Frequency MHz MHz Insertion Loss 4.dB max. 4.dB max. Passband Width (at 3dB) ±13kHz min. ±13kHz min. Stop Band Attenuation 1: Input 2: Output 3: NC : round fn±6khz 3dB min. 3dB min. fn±1.2mhz 4dB min. 4dB min. fn±21.5mhz 6dB min. 6dB min. Ripple (fn±11khz) 1.5dB max. 1.5dB max. roup Delay Time (fn±11khz) 1.2µs max. 1.2µs max. Operating Temperature -1~±6 C -1~±6 C (*) Note PAFC248A fa=21.5mhz PAFC243A fa=21.6mhz 6. Unit: mm Taping Dimension OUT : round Unit: mm 5Ω 4pF 68nH 4pF 82nH 5Ω Unit: mm 13

16 Surface Mount Dielectric Filters KDF Series eneral Description Dielectric Filters are high frequency bandpass filters in the range of 8 MHz to over 1 Hz. Their small size, surface mountability, low insertion loss and good temperature stability make them ideal for cordless or cellular telephones, wireless land security systems, etc. Their construction consists of capacitive coupled tuned ceramic cavities using coaxial connections. This allows elements to be stacked together for different passband configurations. The ceramic material is a very high Q formulation for minimum loss characteristics. Features 1) Surface mountable 2) Compact, with low insertion loss using high Q ceramics 3) Various passband widths available 4) High stability and reliability How to Order KDF PY 2 A Test Circuit 5Ω S 836 C 5Ω R.F. V.M. 1 Model (Kyocera Dielectric Filter) 2 Center frequency 3 Number of poles (PY: 2-pole, RY: 3-pole) 4 Passband width 5 Type number Dimensions (3-pole KDF-RY series) Dimensions (2-pole KDF-PY series) Month date code S S=signal connnection =ground connection S Month date code S=signal connnection =ground connection S (.39) (.315) S.7 5. (.28) (.197) Logo 2. (.79) (.79) (.59) Frequency 1.5 (.59) 1. (.39) 12.5±.5 (.492±.2) 1.5 (.59) 4.5max (.177) Logo 2. (.79) (.79) (.59) 11. max.(.433) Frequency 1.5 (.59) 1. (.39) 8.5±.5 (.335±.2) 4.5max (.177) 1.5 (.59) 12. max.(.472) Units: mm (inch) Tol: ±.3mm Units: mm (inch) Tol: ±.3mm Solder Pad Dimensions (KDF-RY) Solder Pad Dimensions (KDF-PY) S S S=signal connnection =ground connection S S S=signal connnection =ground connection Unit: mm 14 Unit: mm

17 Surface Mount Dielectric Filters KDF Series Specifications KDF-PY Series (2-pole type) Application Parts No. Nominal Center Insertion Loss at Passband Width V.S.W.R Attenuation Frequency (fn) Passband Width (db) (MHz) at Passband Width (db) E-AMPS KDF-836PY25A 836.5MHz KDF-881PY25A 881.5MHz 2.5 max. ±12.5 min. 2.5 max. 7 min. at fn±32.5mhz SM/NMT9 KDF-92PY25A 92.5MHz KDF-947PY25A 947.5MHz 2.5 max. ±12.5 min. 2.5 max. 7 min. at fn±32.5mhz KDF-959PY2A 959.5MHz Europe KDF-914PY2A 914.5MHz 3. max. ±1. min. 2. max. 24 min. at fn±45mhz Cordless Phone KDF931PY2A 931.MHz KDF-886PY2A 886.MHz 3. max. ±1. min. 2. max. 24 min. at fn±45mhz KDF-93PY2A 93.MHz US 3. max. ±1. min. 2. max. 13 min. at fn±24mhz KDF-927PY2A 927.MHz Cordless Phone KDF-915PY26A 915.MHz 2.5 max. ±13. min. 2.5 max. 2 min. at fn±77.5mhz Wireless KDF-88PY8A 88.MHz Microphone KDF-84PY8A 84.MHz 2.5 max. ±4. min. 2. max. 13 min. at fn±27mhz MCA KDF-847PY26A 847.MHz 2.5 max. ±13. min. 2.5 max. 25 min. at fn±97mhz PS KDF-1575PY4A MHz 3.3 max. ±2. min. 2.2 max. 8 min. at fn±2mhz DECT KDF-189PY2A 189.MHz 3. max. ±1. min. 2. max. 25 min. at fn±1 MHz 35 min. at fn±21mhz KDF-RY Series (3-pole type) Application Parts No. Nominal Center Insertion Loss at Passband Width V.S.W.R Attenuation Frequency (fn) Passband Width (db) (MHz) at Passband Width (db) E-AMPS KDF-836RY25A 836.5MHz KDF-881RY25A 881.5MHz 3. max. ±12.5 min. 2. max. 12 min. at fn±32.5mhz E-TACS KDF-888RY33A 888.5MHz KDF-933RY33A 933.5MHz 3. max. ±16.5 min. 2. max. 5 min. at fn±28.5mhz SM/NMT9 KDF-92RY25A 92.5MHz KDF-947RY25A 947.5MHz 3. max. ±12.5 min. 2. max. 12 min. at fn±32.5mhz KDF-959RY2A 959.5MHz Europe KDF-914RY2A 914.5MHz 5. max. ±1. min. 2. max. 4 min. at fn±45mhz Cordless Phone KDF-931RY2A 931.MHz KDF-886RY2A 886.MHz 5. max. ±1. min. 2. max. 4 min. at fn±45mhz KDF-93RY2A 93.MHz US 5. max. ±1. min. 2. max. 25 min. at fn±24mhz KDF-927RY2A 927.MHz Cordless Phone KDF-915RY26A 915.MHz 3. max. ±13. min. 2. max. 12 min. at fn±32.5mhz MCA KDF-847RY26A 847.MHz 3. max. ±13. min. 2. max. 47 min. at fn+97mhz DECT KDF-189RY2A 189.MHz 4.5 max. ±1. min. 2. max. 35 min. at fn±1mhz 45 min. at fn±21mhz 15

18 Surface Mount Dielectric Filters PDFB Series Features 1) Small and light weight 2) Simple leadless structure 3) Wide frequency range from 8Mhz to 2.2Hz Shape and Dimension 8.5±.5 * 914 ** PDFB-PA Tol.: ±.3 * : Kyocera s Mark ** : Month Date Code S : Input/Output : round How To Order PDFB 931 PA 2 R A Model 2 Center frequency 3 Number of poles (PA: 2 poles, RA: 3 poles) 4 Passband width 5 Packaging (R: Taping) 6 Type (A: Standard) * 12.5± ** PDFB-RA 914g Tol. : ±.3 * : Kyocera s Mark ** : Month Date Code S : Input/Output : round 914g max max S S.75 P S S.75 P Unit: mm Specifications PDFB-PA Series (2-pole type) Application Parts No. Nominal Center Insertion Loss at Passband Width V.S.W.R Attenuation Frequency (fn) Passband Width (db) (MHz) at Passband Width (db) E-AMPS PDFB836PA25RA 836.5MHz at fn±32.5mhz 2.5 max. ±12.5 min. 2.5 max. PDFB881PA25RA 881.5MHz 7 min. SM/NMT9 PDFB92PA25RA 92.5MHz at fn±32.5mhz 2.5 max. ±12.5 min. 2.5 max. PDFB947PA25RA 947.5MHz 7 min. PDFB959PA2RA 959.5MHz at fn±45mhz 3. max. ±1. min. 2. max. Europe PDFB914PA2RA 914.5MHz 24 min. Cordless Phone PDFB931PA2RA 931.MHz at fn±45mhz 3. max. ±1. min. 2. max. PDFB886PA2RA 886.MHz 24 min. PDFB93PA2RA 93.MHz at fn±24mhz US 3. max. ±1. min. 2. max. PDFB927PA2RA 927.MHz 13 min. Cordless Phone PDFB915PA26RA 915.MHz 2.5 max. ±13. min. 2.5 max. at fn±77.5mhz 2 min. PDFB-RA Series (3-pole type) Application Parts No. Nominal Center Insertion Loss at Passband Width V.S.W.R Attenuation Frequency (fn) Passband Width (db) (MHz) at Passband Width (db) E-AMPS PDFB836RA25RA 836.5MHz at fn±32.5mhz 3. max. ±12.5 min. 2. max. PDFB881RA25RA 881.5MHz 12 min. E-TACS PDFB888RA33RA 888.5MHz at fn±28.5mhz 3. max. ±16.5 min. 2. max. PDFB933RA33RA 933.5MHz 5 min. SM/NMT9 PDFB92RA25RA 92.5MHz at fn±32.5mhz 3. max. ±12.5 min. 2. max. PDFB947RA25RA 947.5MHz 12 min. PDFB959RA2RA 959.5MHz at fn±45mhz 5. max. ±1. in 2. max. Europe PDFB914RA2RA 914.5MHz 4 min. Cordless Phone PDFB931RA2RA 931.MHz at fn±45mhz 5. max. ±1. min. 2. max. PDFB886RA2RA 886.MHz 4 min. PDFB93RA2RA 93.MHz at fn±24mhz US 5. max. ±1. min. 2. max. PDFB927RA2RA 927.MHz 25 min. Cordless Phone PDFB915RA26RA 915.MHz 3. max. ±13. min. 2. max. at fn±32.5mhz 12 min. 16

19 Surface Mount Dielectric Filters PDFB Series Frequency Characteristics Cordless phone (2 poles) Cordless phone (3 poles) Att. (db) 5 Att. (db) CENTER 886.MHz SPAN 25.MHz MRK 1: fn-45.mhz 2: fn+45.mhz 1 CENTER 886.MHz SPAN 25.MHz MRK 1: fn-45.mhz 2: fn+45.mhz Recommended Land Pattern PDFB-PA PDFB-RA b b 4. b b b 4. b a b a b P b b b a a P Filter mount area Land Pattern a: Input/Output b: round Taping Dimension PDFB-PA PDFB-RA ø1.55 ø (1.75) ~1.7 (Depend on fn) ~1.4 (Depend on fn) ø1.55 ø (1.75) ~1.7 (Depend on fn) ~1.4 (Depend on fn) Recommended Reflow Soldering Condition (IR Reflow) Test Circuit Temp. (C ) 25 2 C min. 15 sec. max. Peak Temp. 23 C ±5 C C min. 4 sec. max. Rg S.S.. RL RF Voltmeter 5 Rg=RL=5Ω 17

20 Surface Mount Dielectric Filters - PHS/DECT PDFB Series Features 1) Ultra miniature 2) High selectivity Applications 1) Japan digital cordless phone system (PHS) 2) European digital cordless phone (DECT) How To Order PDFB 197 P C 24 R B Model 2 Center frequency (197: PHS, 189: DECT) 3 Number of poles (P: 2 poles) 4 Element size (C: 2.2mm sq.) 5 Passband width (MHz) 6 Packing (R: Taping only) 7 Type (B: Low I.L., C: High attenuation) 197g 197g Shape and Dimension PDFB197PC24RB PDFB197PC24RC * 4.9 Tol : ±.3 I/O : Input/Output : round : Month Date Code * * 4.1 Tol : ±.3 I/O : Input/Output : round : Month Date Code * I/O I/O Unit: mm Specifications PHS Part Number PDFB197PC24RB PDFB197PC24RC Nominal Center Frequency (fn) 197MHz 197MHz Passband Width fn±12mhz fn±12mhz Insertion Loss at Passband Width 1.dB max. 2.dB max. V.S.W.R. Passband Width 1.7 max. 1.7 max. Ripple Passband Width.5dB max..5db max. fn 5MHz 38dB min. 3dB min. fn 25MHz 15dB min. 4dB min. Attenuation fn 125MHz 15dB min. fn+25mhz 7dB min. 2dB min. 2fn.3fn 2dB min. Max. Input Power 1W 1W I/O Impedance 5Ω 5Ω Operating Temperature -2~+6 C -2~+6 C Storage Temperature -3~+85 C -3~+85 C DECT Part Number PDFB189PC2RC Nominal Center Frequency (fn) 189MHz Passband Width fn±1mhz Insertion Loss at Passband Width 2.dB max. V.S.W.R. Passband Width 2. max. Ripple Passband Width.5dB max. fn 21MHz 35dB min. Attenuation fn 1MHz 13dB min. 2fn.3fn Max. Input Power 1W I/O Impedance 5Ω Operating Temperature -2~+6 C Storage Temperature -3~+85 C 18

21 Surface Mount Dielectric Filters - PHS/DECT PDFB Series Frequency Characteristics Recommended Land Pattern PDFB197PC24RB I/O : Input/Output : round Attenuation (db) Frequency (MHz) 1 Fn-5MHz 2 Fn-25MHz 3 Fn-125MHz 4 Fn+25MHz I/O 1.2 b I/O a b PDFB197PC24RB PDFB197PC242RC : Cu foil eliminated area.8 a.8 Filter mount area PDFB197PC24RB Taping Dimension ø Attenuation (db) Fn 2 2Fn 3 3Fn 4 2Lo 5 3Lo 8 ø1.55 (6.75) RC: 4.9 RB: 5.7 B Bo RC: 4.6 RB: Frequency (MHz) 65 PDFB197PC24RC Recommended Reflow Soldering Condition (IR Reflow) Temp. (C ) Attenuation (db) Fn-5MHz 2 Fn-25MHz 3 Fn-125MHz 4 Fn+25MHz C min. 15 sec. max. Peak Temp. 23 C ±5 C 18 C min. 4 sec. max Frequency (MHz)

22 EMI Noise Filters KNF 32 Series Features 1) Stable attenuation without ringing with distributed parameter circuit 2) Low profile (1mm,.4 in) 126 type 3) Simple construction Applications 1) Personal computers, LBP :Clock output (signal) line :I/O line (ex. video signal line such as VA, XA) 2) Digital cellular phones 3) Other high speed digital circuits, for example digital TV, VTR How To Order KNF W Series 2 Size: 32=126, 21=85 3 Type (Freq.): 126: 25=25MHz, 5=5MHz 1=1MHz, 2=2MHZ 85: 5=5MHz, 1=1MHz 2=2MHz, 4=4MHz 4 Taping direction (X, Y) W (STD) 5 Quantity per reel: 2=2p, 3=3p X Shape and Dimensions Equivalent Circuit 3.2 (.126) 2.±.2 (.79) IN OUT 1.6 (.63) ±.2 (.49) ND Polarity Mark Input Direction Mark IN ND OUT 1. (.4) 8±.15 (.31).6 (.24).3±.2 (.12).4±.3 (.16).3±.2 (.12) Unit: mm (inch) Specifications Type Cut off Capacitance Typical Freq. (+5/-2%) Attenuation (db) KNF MHz 235pF 2 (2-6MHz) KNF325 5MHz 13pF 2 (35-85MHz) KNF321 1MHz 65pF 2 (45-95MHz) KNF322 2MHz 33pF 2 (6-11MHz) KNF215 5MHz 13pF 2 (35-85MHz) KNF211 1MHz 65pF 2 (45-95MHz) KNF212 2MHz 33pF 2 (7-12MHz) KNF214 4MHz 17pF 2 (9-14MHz) Rated voltage: 25VDC Rated current: 2mA Attenuation of cut off frequency: max. -6dB Attenuation characteristics should be standard characteristics of 5Ω (MIL-STD-22A Performance Characteristics Attenuation (db) MHz 25MHz 2MHz 1MHz Frequency (MHz) 2

23 EMI Noise Filters KNF 32 Series Typical Example of Suppression KC KNF325 Spectrum Attenuation (db) 1 Distributed Parameter Circuit Frequency (MHz) OUTPUT WAVE FORM 2V 2ns ORIINAL WAVE FORM 2V 2ns LC Filter Spectrum Attenuation (db) 1 Lumped Parameter Circuit Frequency (MHz) 2V 2ns 74HC4 FILTER 74HC 1MHz 15cm Measuring Point Land Pattern Resist ø.5(.2) Via to round Resist ø.3-.4( ) Through Hole.6 (.24) 1.4 (.55) 3. (.118).6 (.24) 1. (.39) 2.3 (.91).6(.24).4(.16) 1.2(.47) 2.5(.1).8(.31) 1.2(.47) 4.4(.173) 3.2(.126) Unit: mm (inch) 21

24 Myrtle Beach, SC / Tel: / FAX: Vancouver, WA / Tel: / FAX: Olean, NY / Tel: / FAX: Raleigh, NC / Tel: / FAX: Biddeford, ME / Tel: / FAX: AVX Limited, Fleet, Hants, England / Tel: (1252) 77 / FAX: (1252) 771 AVX S.A., France / Tel: (1) / FAX: (1) AVX mbh, ermany / Tel: / FAX: AVX s.r.l., Milano, Italy / Tel: / FAX: AVX/Kyocera (HK) Ltd. / Tel: / FAX: AVX/Kyocera (Singapore) Pte. Ltd. / Tel: (65) / FAX: (65) AVX Israel Ltd. / Tel: / FAX: AVX/Kyocera Corp. / Tel: / FAX: AP-FIL5975M-C