Products. Dielectric Resonators. Description: Specifications: Attenuation:
|
|
|
- Wesley Holmes
- 6 years ago
- Views:
Transcription
1 Dielectric Resonators Products Description: K&L s Dielectric Resonator Bandpass Filters are available in standard packages with a basic Chebychev design. Connectors available are SMA and RF pins. Through the use of ceramic technology, this filter series offers superior temperature stability and low insertion loss. Frequency (MHz) 3 db % BW VSWR Impedance (Ohms) : No. of Sections Shock Vibration 20 G s, 1/2 Sine, 11 Ms 10 G s, 10 Hz Hz Temperature -40 to +85 C (Operating) -50 to +125 C (Non-Operating) Temp. Stability +2 to +11 ppm/ C Relative Humidity 0-95% Attenuation: The adjacent curve shows the attenuation as multiples of the bandwidth for filters with 2-6 sections. The following formula is used: 3 db bandwidths from center frequency= Reject Frequency - Center Frequency 3 db Bandwidth Example: Center Frequency = 1000 MHz 3 db Bandwidth = 50 Number of Sections = 5 Find the attenuation at 900 and 1100 MHz by substituting in the formula 3 db bandwidth from center frequency = = -2 BW s 50 and 3dB bandwidth from center frequency = = +2 BW s 50 From the curve, we find the attenuation in db for a 5-section response -2 bandwidths from center frequency to yield 46 db, and +2 bandwidths from center frequency to yield 44 db. 66
2 Dielectric Resonators Products To Order: 3 DR / T 50 O / O Code Description 1 Number of Sections 2 Series 3 Package/Resonator Designator 4 Center Frequency 5 Supplemental Codes (See Page 13) 6 Bandwidth 7 Input Connector 8 Output Connector Connectors: Connector SMA Female SMA Male Gull Wing Code O OP PX Height For Mechanical Definitions see or contact our factory. 67
3 Bandpass Filters Features: Designed for Low Cost While Providing High Q Response Extremely Temperature Stable Covers the 270 MHz to 3000 MHz Frequency Range 3 db BW Available up to 30% Designs Available in 2-6 Sections Chebyshev Design Response Series 3 and 5 are ROHs complient See page 44 for Reflow Profile and Suggested Mounting Information. Center Frequency (MHz) db % BW Up to 30% VSWR 2.0:1 Attenuation Impedance (Ohms) 60 dbc ( MHz) dbc ( MHz) Number of Sections 2-6 * For more complete specifications please visit us at Shock 20 G s 1/2 Sine, 11 Ms Vibration 10 G s 10 Hz Hz Temp. -40 to +85 C (Operating) -50 to C (Non-Operating) Temp. Rel. Stability Humidity +2 to +11 ppm/ C 0-95% Recommended PCB Layout:.xxx = Dim. A.yyy= Dim. B DR 23, 33 Series Depicted Dimensions are determined by Filter Wizard outline..xxx = Dim. A.yyy= Dim. B DR 25, 35 Series Depicted Dimensions are determined by Filter Wizard outline. 68
4 Bandpass Filters Mechanical Note: Dimensions for 1000 MHz filters shown 3DR /U Leadless Surface Mount - Series 5 This mounting configuration offers best isolation. 3DR /U Surface Mounting - Tab 3DR /U Drop in (PC) Mounting 69
5 Special Applications 5.8 GHz Bandpass Filters Features: Low Cost, Small Package, High Q Response Extremely Temperature Stable Clean Out-of-Band Response 3 Section Standard, 2-6 Sections also Available, Contact Factory Chebyshev Design Response Other Package Styles Available, Contact Factory See Page 44 for Reflow Profile and Suggested Mounting Information Model Number: 3DT /x100 Center Frequency: 5768 MHz Operating Bandwidth: 100 MHz Insertion f 0 : +/-250 MHz -25 dbc Stopband Rejection: up to 20 GHz VSWR: 2.0:1 Number of Sections: 3 Impedance (Ohms): 50 Shock: 20 G s, 1/2 Sine, 11 Ms Operating Temperature: -40 to +85 C Storage Temperature: -50 to +125 C Temperature Stability: +2 to +11 ppm/ C Relative Humidity: 0-95% Package Style: Leadless surface mount Dimensions: 0.55 L x 0.80 W x 0.20 H [14 x 20.3 x 5mm] Applications: C-band applications: - Wireless LAN, LPS (Local Positioning Systems), etc. Performance Data In-Band Response Typical Out-of-Band Response Out-of-Band Response with Integrated Clean-up Circuit 70
ponents Com ped Lum Lumped Components
Lumped Components Lumped Components K&L Microwave offers Lumped Component filters with a broad selection of frequencies, topologies, and mechanical configurations. Use of standard packages has enabled
Part Numbering System
Reactel Filters can satisfy a variety of filter requirements. These versatile units cover the broad frequency range of 2 khz to 5 GHz, and are available in either tubular or rectangular packages, connectorized
ytivac Cavity Filters
Cavity Cavity Filters K&L Microwave s series of cavity filters covers the frequency range from 30 MHz to 40 GHz. These filters are available with 2 to 17 resonant sections and bandwidths from 0.2% to 50%.
Cavity Filters. Waveguide Filters
Cavity Cavity Filters K&L Microwave s series of cavity filters covers the frequency range from 30 MHz to 40 GHz. These filters are available with 2 to 17 resonant sections and bandwidths from 0.2% to 50%.
K&L s 170,000 square foot facility vertically integrates design, manufacturing, and test centers. Capabilities and certifications are as follows:
K&L Microwave (MPG Salisbury) has been a key supplier to space programs since the Apollo 17 lunar sounder experiment in 1972. Across the decades, K&L has supported customers with high reliability filter
Number of Sections. Contact factory for specific requirements not listed above.
Tubular Filters MHz to 20 GHz Chebyshev Response Standard 4 Convenient Sizes Reliable Sturdy Construction Lorch Microwave tubular filters are available in bandpass and lowpass configurations. A low ripple
SPECIFICATIONS STANDARD *SPECIAL. 200 to 2000 MHz 4 to 40 3 to 8. 30G s 10G s 90% relative Unlimited -25 C to + 50 C -54 C to +70 C. 0.5 oz.
BANDPASS SF SERIES 0-00 MHz NO. OF SECTIONS 2 3 4 5 6 OR MORE 1.5/1 VSWR BW 0.4 0.7 0.8 0.85 0.9 MIN. 3 db BW SPECIFICATIONS STANDARD *SPECIAL ELECTRICAL Center Frequency (Fc) 3dB Relative Bandwidth (%
HIGH-VALUE PHASE-LOCKED COAXIAL RESONATOR OSCILLATOR
OSCILLATOR SECTION HIGH-VALUE PHASE-LOCKED COAXIAL RESONATOR OSCILLATOR BCO SERIES: 0.20 4 GHz (Fundamental) 4 16 GHz (Multiplied) FEATURES Low cost Phase locked to external standard or internal crystal
Filters / Duplexers / Diplexers / RF Assemblies. Commercial, Military and Wireless filter products
Filters / Duplexers / Diplexers / RF Assemblies Commercial, Military and Wireless filter products Excellence in Filter Technologies for the Military, Commercial and Wireless Markets Table of Contents INTRODUCTION
TELONIC FIXED FREQUENCY FILTERS
Established 1981 Advanced Test Equipment Rentals www.atecorp.com 800-404-ATEC (2832) TELONIC FIXED FREQUENCY FILTERS ENGINEERS DESIGN HANDBOOK TABLE OF CONTENTS Introduction............................................1
Return Loss Bridge Basics
1.0 Introduction Return loss bridges have many useful applications for the two-way radio technician These bridges are particularly helpful when used with the tracking generator feature of many service
Model BD1722J50100A00
Ultra Low Profile 85 Balun 5Ω to 1Ω Balanced Description The BD1722J51A is a low profile sub-miniature balanced to unbalanced transformer designed for differential inputs and output locations on next generation
Model BD1631J50100AHF
Model BD1631J51AHF Ultra Low Profile 85 Balun 5Ω to 1Ω Balanced Description The BD1631J51AHF is a low profile sub-miniature balanced to unbalanced transformer designed for differential inputs and output
Block Upconverters for Integration in High Power Amplifiers
R Back to Block/Fixed Tuned Converters Block Upconverters for Integration in High Power Amplifiers Block Upconverters For Integration In High Power Amplifiers C-, X- and Ku-Band Models (except UPBA-13)
DC to 400 MHz (40 db Typ. Isolation up to 20 GHz)
Coaxial Low Pass Filter 5Ω DC to 4 MHz (4 db Typ. Isolation up to 2 GHz) The Big Deal Very good rejection, 4 db typ. up to 2 GHz Excellent power handling, 1W Rugged unibody construction CASE STYLE: FF1118
3H Communication. Systems. RF Filters & Front-End Systems Experts
Relentless Innovations Amplitude 5f1-4f2 4f1-3f2 3f1-2f2 2f1-f2 f1 f2 2f2-f1 3f2-2f1 4f2-3f1 5f2-4f1 Frequency 0 0-10 -20-10 -30-40 -20-50 -60-30 -70-80 -40-90 -100-50 1685 1710 1735 1760 1785 1810 1835
Model BD4859L50100A00 Rev A
Model BD4859L51A Ultra Small Low Profile 63 Balun 5Ω to 1Ω Balanced Description The BD4859L51A is an ultra-small low profile balanced to unbalanced transformer designed for differential inputs and output
Phase Locked Sources Series PDRO Dielectric Resonator Oscillators
Features Options Wide Operating Temperature Range -40 to +75 C Standard Ultra Low Phase-Noise Small Size Field Adjustable Tuning No Subharmonics Ideal for Outdoor Applications Low Cost, Low Profile, Low
bringing technology to life
bringing technology to life For four decades, orch Microwave has continuously supplied RF and Microwave components and systems to the leading military, industrial, and commercial manufacturers worldwide.
FEU (Front End Unit) for Optic Repeater
FEU (Front End Unit) for Optic Repeater 1. Specification 1.1. All Items Parameter Specification Comments RX1 RX2 TX Frequency Range. 1750.625 ~ 1769.375MHz 1750.625 ~ 1769.375MHz 1840.625 ~ 1859.375MHz
50W TO220 High Power Resistors
50W TO220 High Power Resistors MHP 50 Non-inductive, thin film technology. Thermally enhanced Industry standard TO220 package. RoHS compliant. Low thermal resistance, 2.3 C/W resistor hot spot to metal
Features Excellent VSWR, 1.1:1 passband Small size Temperature stable LTCC construction
Ceramic Bandpass Filter 5Ω Maximum Ratings Operating Temperature Storage Temperature 15 to 16 MHz -55 o C to 1 o C -55 o C to 1 o C RF Power Input* 1.5W at 25 o C *Passband rating, derate linearly to.25w
SURFACE MOUNT HIGH REPEATABILITY SPDT, BROADBAND 18 GHZ 40GBPS MAGNETIC-LATCHING RF RELAY
SURFACE MOUNT HIGH REPEATABILITY SPDT, BROADBAND 18 GHZ 40GBPS MAGNETIC-LATCHING RF RELAY Series GRF121/GRF121R SERIES GRF121 GRF121R RELAY TYPE RF Magnetic-Latching, SPDT, Common Coil Negative, Surface
INC. MICROWAVE. A Spectrum Control Business
DRO Selection Guide DIELECTRIC RESONATOR OSCILLATORS Model Number Frequency Free Running, Mechanically Tuned Mechanical Tuning BW (MHz) +10 MDR2100 2.5-6.0 +10 6.0-21.0 +20 Free Running, Mechanically Tuned,
PAGE 1/12 ISSUE SERIES DP3T/SPDT PART NUMBER R595 XXX XXX
PAGE 1/12 ISSUE 22-06-2018 SERIES DP3T/SPDT PART NUMBER R595 XXX XXX DP3T-SPDT Coaxial Switches DC to 6 GHz, DC to 20 GHz, DC to 26.5 GHz, DC to 40 GHz Radiall s PLATINUM SERIES switches are optimised
RF-LAMBDA LEADER OF RF BROADBAND SOLUTIONS
50W Broadband High Power Amplifier Module 500 2500MHz Electrical Specifications, T A = +25⁰C, Vdd = +28V Features Ultra-broadband Amplifier Module Small and lightweight Supply Voltage: +28V Parameter Min.
LB480A Pulse Profiling USB PowerSensor+ Data Sheet
Key PowerSensor+ Specifications 100 MHz to 8 GHz (functional to 10 GHz) -60 dbm to +20 dbm 1.95% Total Error* 1.09:1 VSWR (-27 db Return Loss) * Measuring a well matched DUT (-20 dbm @ 1 GHz) Measurement
Model BD3238N5050AHF. Ultra Low Profile 0404 Balun
Model BD338N55AHF Ultra Low Profile 44 Balun 5Ω to 5Ω Balanced Description The BD338N55AHF is a low cost, low profile sub-miniature unbalanced to balanced transformer designed for differential inputs and
RF Characterization Report
SMA-J-P-H-ST-MT1 Mated with: RF316-01SP1-01BJ1-0305 Description: 50-Ω SMA Board Mount Jack, Mixed Technology Samtec, Inc. 2005 All Rights Reserved Table of Contents Introduction...1 Product Description...1
TELONIC FIXED FREQUENCY FILTERS ENGINEERS DESIGN HANDBOOK
TELONIC FIXED FREQUENCY FILTERS ENGINEERS DESIGN HANDBOOK TABLE OF CONTENTS Introduction............................................1 Aids to use of this Catalog.................................2 Ordering
Features. = +25 C, Vcc = +3V
Typical Applications Low noise MMIC VCO w/buffer Amplifi er for: Wireless Local Loop (WLL) VSAT & Microwave Radio Test Equipment & Industrial Controls Military Features Pout: +4.9 dbm Phase Noise: -3 dbc/hz
HIGH REPEATABILITY SPDT, BROADBAND 12 GHZ, 20 Gbps MAGNETIC-LATCHING RF RELAY
HIGH REPEATABILITY SPDT, BROADBAND 12 GHZ, 20 Gbps MAGNETIC-LATCHING RF RELAY SERIES RF121 RF121R RELAY TYPE RF Magnetic-Latching, SPDT, Common Coil Negative, Through-Hole Relay RF Magnetic-Latching, SPDT,
EDCRO-200 is a stable ceramic based, sampling phase locked oscillator.
EDCRO-200 is a stable ceramic based, sampling phase locked oscillator. Commercial Military Airborne Space Missile Guidance Cable TV Links (CATV) Satellite Communications Low Cost External Reference Military/Commercial
SAW BANDPASS FILTER. ACT PART NO.: ACTF9201_2535MHz_DCC6C
SAW BANDPASS FILTER ACT PART NO.: ACTF9201_2535MHz_DCC6C Product Type: SAW Filter Part NO.: Customer: Customer Part NO.: ACTF9201_2535MHz_DCC6C Issued Date: PREPARED BY CHECKED BY APPROVED BY Features
Model BD2425N50200AHF. Ultra Low Profile 0404 Balun 50Ω to 200Ω Balanced
Model BD45N5AHF Ultra Low Profile 44 Balun 5Ω to Ω Balanced Description The BD45N5AHF is a low cost, low profile sub-miniature unbalanced to balanced transformer designed for differential inputs and output
VI TELEFILTER Filter specification TFS 248F 1/5
VI TELEFILTER Filter specification TFS 248F 1/5 Measurement condition Ambient temperature: 23 C Input power level: 0 dbm Terminating impedance: Input: 50 Ω Output: 200 Ω Characteristics Remark: The reference
OX-046 VHF low g-sensitivity Oven Controlled Crystal Oscillator
OX-046 VHF low g-sensitivity Oven Controlled Crystal Oscillator OX-046 Features Ultra Low G-Sensitivity Low Phase Noise Very High Frequency Frequency Range: 50 MHZ to 250 MHZ Standard Frequency: 100 MHz
Multi-Function Assemblies
K&L Microwave offers a variety of (MFA) products to satisfy a broad range of filtering applications. Many applications require frequency pre-selection at the front end of the communication or test and
1 GHz capable, 3 W carrying power (at 1 GHz), 50Ω impedance and 2 Form C relays
1 GHz capable, 3 W carrying power (at 1 GHz), 5Ω impedance and 2 Form C relays RA RELAYS (ARA) 9.7 14.7.382.579 5.9.232 mm inch RoHS compliant Protective construction: Sealed type ORDERING INFORMATION
SURFACE MOUNT HIGH REPEATABILITY SPDT, BROADBAND 16 GHZ 40GBPS MAGNETIC-LATCHING RF RELAY
SURFACE MOUNT HIGH REPEATABILITY SPDT, BROADBAND 16 GHZ 40GBPS MAGNETIC-LATCHING RF RELAY Series GRF121 SERIES GRF121 RELAY TYPE RF Magnetic-Latching, SPDT, Surface Mount Relay DESCRIPTION The ultraminiature
The Reverse Polarity TNC(m) RF connector can be easily secured or removed from equipment in the field by a single gloved hand, no tools required.
Overview Southwest Antennas is a half wave dipole omni antenna with a frequency range of 1.35 to 1.40 GHz and 2.15 dbi of peak gain. This product features an integrated RF bandpass filter to help eliminate
Model PD3150J5050S2HF
Model PD315J55S2HF Ultra Low Profile 85 Power Divider 5Ω to 5Ω Description The PD315J55S2HF is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package. The PD315J55S2HF
RESISTIVE POWER SPLITTERS AND DIVIDERS
RESISTIVE POWER SPLITTERS AND DIVIDERS DC 40.0 GHz S Resistive Power Splitters Usage: : Use in RF and wireless applications where one of the two outputs are included in a leveling loop or used as a reference
LTCC Components. ShenZhen Sunlord Electronics CO., LTD.
LTCC Components Content 1 The concept of LTCC About LTCC technology 2 Sunlord LTCC components Multilayer chip Antenna Multilayer chip Filter Multilayer chip Diplexer Multilayer chip Balun Multilayer chip
Gain Slope issues in Microwave modules?
Gain Slope issues in Microwave modules? Physical constraints for broadband operation If you are a microwave hardware engineer you most likely have had a few sobering experiences when you test your new
Top View (Near-side) Side View Bottom View (Far-side) .89±.08. 4x.280. Orientation Marker Orientation Marker.
Model B2F2AHF Ultra Low Profile 168 Balun Ω to 2Ω Balanced Description The B2F2AHF is a low profile sub-miniature balanced to unbalanced transformer designed for differential input locations on data conversion
VI TELEFILTER Resonator specification TFR 868D 1/5
VI TELEFILTER Resonator specification TFR 868D 1/5 Measurement condition Ambient temperature: 25 C Input power level: 0 dbm Terminating impedance * for input: 50Ω for output: 50Ω Characteristics Remark:
Features. = +25 C, Vcc = +3V
Typical Applications Low noise MMIC VCO w/buffer Amplifi er for: VSAT & Microwave Radio Test Equipment & Industrial Controls Military Features Pout: +dbm Phase Noise: -106 dbc/hz @100 khz No External Resonator
ATC 1206 LPF Series High Performance SMT Thin Film Low Pass Filter
ATC 126 HIGH PERFORMANCE LOW PASS FILTER ATC 126 LPF Series High Performance SMT Thin Film Low Pass Filter Features: Sharp Cut-off Response Excellent Stopband rejection Characteristic : 5Ω No External
Features. = +25 C, Vcc = +5V. Parameter Min. Typ. Max. Units Fo Fo/2 RFOUT RFOUT/2
Typical Applications Low noise MMIC VCO w/half Frequency, for: VSAT Radio Point to Point/Multi-Point Radio Test Equipment & Industrial Controls Military End-Use Functional Diagram Features Dual Output:
Vectron International Filter specification TFS246R 1/5
Vectron International Filter specification TFS26R 1/5 Measurement condition Ambient temperature: 23 C Input power level: 0 dbm Terminating impedances*): input: 695 Ω -1.9 pf output: 695 Ω -1.9 pf Characteristics
OX-043 Low g-sensitivity Oven Controlled Crystal Oscillator
OX-043 Low g-sensitivity Oven Controlled Crystal Oscillator OX-043 Features Applications Ultra Low g-sensitivity Low Phase Noise High Stability Frequency Range: 8 MHZ to 15 MHZ Standard Frequency 10 MHz
Detailed Electrical Specifications: Specifications subject to change without notice. Broadband Narrowband 25 C
fee Ultra Low Profile 85 Balun 75Ω to 75Ω Balanced Description The B225J7575AHF is a low profile sub-miniature balanced to unbalanced transformer designed for differential inputs and output locations on
VS-800 Ultra-Low Jitter High Frequency VCSO
VS-800 Ultra-Low Jitter High Frequency VCSO VS-800 Description The VS-800 is a Voltage Controlled SAW Oscillator that operates at the fundamental frequency of the internal SAW resonator. The SAW resonator
VI TELEFILTER Filter specification TFS 130C 1/5
VI TELEFILTER Filter specification TFS 130C 1/5 Measurement condition Ambient temperature: 23 C Input power level: 0 dbm Terminating impedance: * Input: 130 Ω -11.6 pf Output: 86 Ω -11.8 pf Characteristics
Data Specification. Model Numbers: Trusted RF Solutions.
µfilter Data Specification Model Numbers: µfilter SF & µfiltercf Trusted RF Solutions. NuWaves Engineering 132 Edison Drive Middletown, Ohio 45044 PH: 513 360 0800 FAX: 513 539 8782 www.nuwaves.com product.sales@nuwaves.com
Top View (Near-side) Side View Bottom View (Far-side) ± ±.08. 4x.28. Orientation Marker Balanced port 1.
Model BD2FAHF Ultra Low Profile 168 Balun Ω to Ω Balanced Description The BD2FAHF is a low profile sub-miniature balanced to unbalanced transformer designed for differential input locations on data conversion
AN-B21C-0004 Applications Note
Rev. A, 10/12/09 SD 2009 Coto Technology All Rights Reserved 1/10 B21C Relay Specification Data TEST PARAMETERS CONDITIONS 1,2 MIN NOM MAX UNITS COIL SPECIFICATIONS COIL RESISTANCE 140.0 155.0 170.0 Ω
SDA SMA DATA SHEET
0 to 60 db 10 Bit Programmable TTL Controlled Step Attenuator With a 006 db Step SMA Female To SMA Female From 500 MHz To 18 GHz The is a Non-Reflective 10 Bit Programmable 60 db Pin Diode Attenuator with
MAGNETIC-LATCHING DPDT HALF-SIZE CRYSTAL CAN HIGH POWER RF RELAY DC-3 GHZ
MAGNETIC-LATCHING DPDT HALF-SIZE CRYSTAL CAN HIGH POWER RF RELAY DC-3 GHZ SERIES RELAY TYPE Commercial, DPDT, High Power, Half-Size Crystal Can Relay Commercial, DPDT, High Power, Half-Size Crystal Can
RF Signal Relays AXICOM. HF3 Relay
HF3 Relay n Y-Design n Frequency range DC to 3GHz n Impedance 50Ω or 75Ω n Small dimensions (14.6x7.2x10mm) n 1 form C contact (1 changeover contact) n Immersion cleanable n Low power consumption ( 140mW)
RF/Microwave Filters. Product & Capabilities Overview
RF/Microwave Filters Product & Capabilities Overview API LOCATIONS Filter Locations Include: Columbia, MD Design Delmar, DE Design & Manufacturing Nashua, NH Design & Manufacturing Rancho Cordova, CA Design
HIGH REPEATABILITY, TO-5 RELAYS DPDT
HIGH REPEATABILITY, TO-5 RELAYS DPDT SERIES RELAY TYPE RF7 RF7 Repeatable, RF relay Sensitive, repeatable, RF relay DESCRIPTION The ultraminiature RF7 and RF7 relays are designed to provide improved RF
SEMS-4079-SP8T-SMA DATA SHEET
SP8T Latching Electro-Mechanical Relay Switch From DC to 18 GHz, 100 Watts with Self Cut Off, Auto Reset, Indicators, Diodes, SMA The SEMS-4079-SP8T-SMA is an SP8T Terminated Electromechanical Relay Switch
Model B0922N7575AHF Rev B. Ultra Low Profile 0404 Balun
Model B9N7575AHF Ultra Low Profile 44 Balun 75Ω to 75Ω Balanced Description The B9N7575AHF is a low profile, low impedance mm square subminiature wideband unbalanced to balanced transformer designed for
RF-LAMBDA LEADER OF RF BROADBAND SOLUTIONS
80W Broadband High Power Amplifier Module 20-1000MHz Electrical Specifications, T A = +25⁰C, VDD = +28V Features Broadband High Power High Efficiency Great Linearity Small Size & Light Weight Low Distortion
Tfs248e.doc version VI TELEFILTER Filter specification TFS 248 E 1/5. D a t a typ. Value Limit
Filter specification TFS 248 E 1/5 Measurement condition Ambient temperature: 23 C Input power level: 0 dbm Terminating impedances at f c *) Input: 560 Ω -5.9pF Characteristics Output: 500 Ω -6.3 pf Remark:
Features. = +25 C, Vdc = +12V
Typical Applications The VCO Module is ideal for: Industrial/Medical Equipment Test & Measurement Equipment Military Radar, EW & ECM Lab Instrumentation Functional Diagram Electrical Specifications, T
Advanced Test Equipment Rentals ATEC (2832)
Established 1981 Advanced Test Equipment Rentals www.atecorp.com 800-404-ATEC (2832) Agilent 2-Port and 4-Port PNA-X Network Analyzer N5249A - 10 MHz to 8.5 GHz N5241A - 10 MHz to 13.5 GHz N5242A - 10
Four-Channel Switchable/Reconfigurable Filter Bank
Four-Channel Switchable/Reconfigurable Filter Bank Contact information for competition organizers: Sanghoon Shin, s.shin@ieee.org Eric Naglich, eric.j.naglich@ieee.org Contest Description and Rules: A
Return loss (db) Insertion loss (db) .56±.06 TBD. GND / DC Feed 1 + RF GND 2. Unbalanced Port Balanced Port Balanced Port.
Model BD6N5AHF Ultra Low Profile 44 Balun 5Ω to Ω Balanced Description The BD6N5AHF is a low cost, low profile sub-miniature unbalanced to balanced transformer designed for differential inputs and output
A DROP-IN REPLACEMENT SOLUTION FOR YOUR EMI / EMC COMPLIANCE PROBLEM
3HM57 Group R A DROP-IN REPLACEMENT SOLUTION FOR YOUR EMI / EMC COMPLIANCE PROBLEM The principle sources of the EMI problem come from the system clocks. Therefore, rather than patch the problem with ferrite
LoopBack Relay. GLB363 Series. With Built-in AC Bypass Capacitors / DC LoopBack Relay
GLB363 Series With Built-in AC Bypass Capacitors / DC SERIES DESIGNATION GLB363 RELAY TYPE, Sensitive Coil, Surface Mount Ground Shield and Stub pins with AC Bypass Capacitors or No capacitor DESCRIPTION
LB679A CW and Pulse (Modulation) USB PowerSensor+ Data Sheet
Key PowerSensor+ Specifications 50 MHz to 20 GHz - 40 dbm to +20 dbm 2.8% Total Error* 1.20:1 VSWR (-21 db Return Loss) * Measuring a well matched DUT (-20 dbm @ 2 GHz) Key PowerSensor+ Capability Test
HELLAS INDUSTRIES. for custom designs since 1980 in. Custom RF Filter & Frequency Control Solutions. Defence Avionics Medical Telecom
HELLAS Custom RF Filter & Control Solutions The Choice for custom designs since 1980 in Monolithic Crystal Filters Discrete Crystal Filters LC Filters Switch Filter assemblies Oscillators INDUSTRIES Defence
OX-175 Ultra Low Noise Oven Controlled Crystal Oscillator
OX-175 Ultra Low Noise Oven Controlled Crystal Oscillator OX-175 The OX-175 is a low phase noise, high-frequency ovenized crystal oscillator in a 28 x 38 mm package. The oscillator has a noise floor of
Model PD0409J7575S2HF
Model PD49J77SHF Ultra Low Profile 8 Power Divider 7Ω to 7Ω Description The PD49J77SHF is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package. The PD49J77SHF is
HIGH REPEATABILITY, DC-8 GHz/20Gbps TO-5 RELAYS, DPDT
HIGH REPEATABILITY, DC-8 GHz/Gbps TO-5 RELAYS, DPDT SERIES RELAY TYPE RF3 RF33 Repeatable, RF relay Low Power Operating Coil, RF relay DESCRIPTION The ultra miniature RF3 is designed to improve upon the
Model PD0409J5050S2HF
Model PD49JSHF Ultra Low Profile 8 Power Divider Ω to Ω Description The PD49JSHF is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package. The PD49JSHF is ideal for
VS-701 High Shock Discrete Voltage Controlled SAW Oscillator
VS-701 High Shock Discrete Voltage Controlled SAW Oscillator VS-701 The VS-701 VCSO (Voltage Controlled Saw Oscillator from Vectron is a high frequency, ultra low phase noise oscillator designed to support
Features. = +25 C, IF= 100 MHz, LO= +15 dbm* Parameter Min. Typ. Max. Min. Typ. Max. Units
v2.514 MIXER, 2.5-7. GHz Typical Applications The is ideal for: WiMAX & Fixed Wireless Point-to-Point Radios Point-to-Multi-Point Radios Test Equipment & Sensors Military End-Use Functional Diagram Features
Model PD2328J5050S2HF
Model PD2328J55S2HF Ultra Low Profile 85 Power Divider 5Ω to 5Ω Description The PD2328J55S2HF is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package. The PD2328J55S2HF
4320 Anthony Court, Suite 16, Rocklin, California
4320 Anthony Court, Suite 16, Rocklin, California 95677 916 672 6356 1 About TechPlus Microwave FOUNDED IN 2012 BY EXPERTS IN FILTER DESIGN AND MANUFACTURING, TECHPLUS MICROWAVE, INC. IS A STATE-OF-THE-ART,
PAGE 1/6 ISSUE Jul SERIES Micro-SPDT PART NUMBER R516 XXX 10X R 516 _ 1 0 _
PAGE 1/6 ISSUE Jul-24-2017 SERIES Micro-SPDT PART NUMBER R516 XXX 10X R516 series: the RAMSES concept merges with the SLIM LINE technology, breaking up the frequency limits of SMT switches : - FULL SMT
Features and Technical Specifications
Features and Technical Specifications PRODU C T SUM M AR Y The HL9402 is a signal splitter and combiner that offers industry-best amplitude and phase match over a bandwidth of 500 khz to 20 GHz (-3 db).
VI TELEFILTER Filter Specification TFS 211 C 1/5
Filename: tfs211c.doc version 3.0 23.01.2002 Filter Specification TFS 211 C 1/5 Measurement condition Ambient temperature: 20... 25 C Input power level: 5 ± 2 dbm terminating impedances * Input: 1,1 kω
TITANIUM SERIES R 51 PART NUMBER SELECTION. High Performance Multiport Switches. Our Most Important Connection is with You.
PART NUMBER SELECTION Models: 2: Without 50 Ω terminations 4: With 50 Ω terminations RF Connectors: 3: SMA up to 6 GHz 4: SMA up to 20 GHz F: SMA up to 26.5 GHz 8: SMA 2.9 up to 40 GHz (1) Radiall s TITANIUM
SURFACE MOUNT HIGH REPEATABILITY, BROADBAND TO-5 RELAYS DPDT
SURFACE MOUNT HIGH REPEATABILITY, BROADBAND TO-5 RELAYS DPDT SERIES GRF300 GRF300D GRF300DD GRF303 GRF303D GRF303DD RELAY TYPE Repeatable, RF relay Repeatable, RF relay with internal diode for coil transient
Product Classification. Mechanical Specifications. Dimensions. Regulatory Compliance/Certifications. Included Products
ATBTK-FM Bias Tee Kit, AISG Compatible 698-2170 MHz Product Classification Product Type RET bias tee Mechanical Specifications Antenna Interface BTS Interface 7-16 DIN Male 7-16 DIN Female Dimensions Depth
HMC6380LC4B. WIDEBAND VCOs - SMT. Electrical Specifications, T A. Typical Applications. Features. General Description. Functional Diagram
Typical Applications Low Noise wideband MMIC VCO is ideal for: Industrial/Medical Equipment Test & Measurement Equipment Satcom Military Radar, EW, & ECM Functional Diagram Features Wide Tuning Bandwidth
Specification AXIOM210 Rev.: 3 Date: Oscillator type: Ultra-Low Phase Noise OCXO in Vibration-isolated Package
in Specification AXIOM210 Rev.: 3 Date: 2015-02-17 Oscillator type: Ultra-Low Phase Noise OCXO in Vibration-isolated Package Parameter min. typ. max. Unit Condition Frequency range 50 130 MHz Standard
VI TELEFILTER Filter specification TFS 230 1/5
VI TELEFILTER Filter specification TFS 230 1/5 Measurement Condition Ambient Temperature: 23 C Input Power Level: 0 dbm Terminating impedances *: for input: 1,95 kω // -5,0 pf for output: 1,67 kω // -5,3
KU-BAND OUTDOOR BLOCK CONVERTERS
Features/Options Low Phase Noise Exceeds IESS 308/309 25 db L-Band Gain Control with 0.1 db Step Auto Switch Over to an Internal High Stability REF Internal REF Tune to Match with External
Vectron International Filter specification TFS /5
Vectron International Filter specification TFS 1795 1/5 Measurement condition Ambient temperature: 2 C Input power level: dbm Terminating impedance: Input: 5 Ω Output: 5 Ω Characteristics Remark: The maximum
Series CCS-37S/CS-37S Miniature DC 18 GHz Failsafe TRANSFER Coaxial Switch
COAX SWITCHES Series CCS-37S/CS-37S PART NUMBER CCS-37S CS-37S DESCRIPTION Commercial Failsafe TRANSFER, DC-8GHz Elite Failsafe TRANSFER, DC-8GHz The CCS-37S/CS-37S is a long-life high performance transfer
Model C1517J5003AHF. Ultra Low Profile db, 90 Hybrid Coupler
Model C57J53AHF Ultra Low Profile 85 3 db, 9 Hybrid Coupler Description The C57J53AHF is a low cost, low profile sub-miniature high performance 3 db coupler in an easy to use surface mount package. The
OBSOLETE HMC881LP5E FILTERS - TUNABLE - SMT. FILTER - TUNABLE, LOW PASS SMT GHz. Typical Applications. General Description. Functional Diagram
Typical Applications The is ideal for: Test & Measurement Equipment Military RADAR & EW/ECM SATCOM & Space Industrial & Medical Equipment Functional Diagram v1.11 Electrical Specifications, T A = +25 C
OX-304 at 10 MHz Ultra Low Phase Noise Oven Controlled Crystal Oscillator
OX-304 at 10 MHz Ultra Low Phase Noise Oven Controlled Crystal Oscillator OX-304 The OX-304 is an Ultra Low Phase Noise Ovenized Crystal Oscillator with a noise floor as low as -173 dbc/hz in a compact
Series CCP-32N Low PIM DC 3 GHz Latching SPDT Coaxial Switch
COAX SWITCHES Series CCP-32N PART NUMBER CCP-32N DESCRIPTION Commercial Latching SPDT, DC-3GHz, Low PIM These switches are designed to have extremely low passive intermodulation for use in narrow bandwidth
LoopBack Relay. LB363 Series. With Built-in AC Bypass Capacitors. LoopBack Relay, Sensitive Coil, thru-hole with AC Bypass Capacitors
LB363 Series With Built-in AC Bypass Capacitors SERIES DESIGNATION LB363 RELAY TYPE, Sensitive Coil, thru-hole with AC Bypass Capacitors DESCRIPTION The LoopBack Series relay combines two DPDT electromechanical