FERROXCUBE DATA SHEET. E30/15/7 E cores and accessories. Supersedes data of November Feb 01

Transcription

1 FERROXCUBE DATA SHEET E3/15/7 Supersedes data of November 2 22 Feb 1

2 E3/15/7 CORE SETS Effective core parameters SYMBOL PARAMETER VALUE UNIT Σ(I/A) core factor (C1) 1.12 mm 1 V e effective volume 4 mm 3 I e effective length 67. mm A e effective area 6. mm 2 A min minimum area 49. mm 2 m mass of core half 11 g handbook, halfpage R R1 15 ± CBW32 Fig.1 E3/15/7 core half. Core halves A L measured in combination with a non-gapped core half, clamping force for A L measurements 2 ±1 N, unless stated otherwise. GRADE A L (nh) µ e AIR GAP (µm) 3C81 1 ±5% (1) E3/15/7-3C81-E1 16 ±5% E3/15/7-3C81-A16 25 ±5% E3/15/7-3C81-A ±5% E3/15/7-3C81-A315 4 ±8% E3/15/7-3C81-A4 63 ±15% 56 1 E3/15/7-3C81-A63 25 ±25% 222 E3/15/7-3C81 3C9 1 ±5% (1) E3/15/7-3C9-E1 16 ±5% E3/15/7-3C9-A16 25 ±5% E3/15/7-3C9-A ±5% E3/15/7-3C9-A315 4 ±8% E3/15/7-3C9-A4 63 ±15% 56 1 E3/15/7-3C9-A63 19 ±25% 169 E3/15/7-3C9 3C91 25 ±25% 222 E3/15/7-3C91 3C94 19 ±25% 169 E3/15/7-3C94 3C96 16 ±25% 142 E3/15/7-3C96 22 Feb 1 2

3 E3/15/7 GRADE 3F3 1 ±5% (1) E3/15/7-3F3-E1 16 ±5% E3/15/7-3F3-A16 25 ±5% E3/15/7-3F3-A ±5% E3/15/7-3F3-A315 4 ±8% E3/15/7-3F3-A4 63 ±15% 56 1 E3/15/7-3F3-A63 16 ±25% 142 E3/15/7-3F3 3F ±25% 111 E3/15/7-3F35 Note 1. Measured in combination with an equal gapped core half, clamping force for A L measurements, 2 ±1 N. Core halves of high permeability grades Clamping force for A L measurements 2 ±1 N. GRADE A L (nh) A L (nh) µ e AIR GAP (µm) µ e AIR GAP (µm) 3C11 33 ±25% 293 E3/15/7-3C11 3E27 41 ±25% 364 E3/15/7-3E27 22 Feb 1 3

4 E3/15/7 Properties of core sets under power conditions B (mt) at Properties of core sets under power conditions (continued) Note 1. Measured at 6 C. CORE LOSS (W) at GRADE H=25A/m; f = 25 khz; f=1khz; f=1khz; f=4khz; f = 25 khz; Bˆ =2mT; Bˆ =1mT; Bˆ =2mT; Bˆ =5mT; T=1 C T=1 C T=1 C T=1 C T=1 C 3C C C (1) 1.6 (1) 3C C F F35 3 B (mt) at CORE LOSS (W) at GRADE H=25A/m; f=5khz; f = 5 khz; f=1mhz; f=3mhz; f = 25 khz; Bˆ =5mT; Bˆ =1mT; Bˆ =3mT; Bˆ =1mT; T=1 C T=1 C T=1 C T=1 C T=1 C 3C C9 33 3C C C F3 32 3F Feb 1 4

5 E3/15/7 COIL FORMERS GENERAL DATA FOR E3/15/7 COIL FORMER WITHOUT PINS PARAMETER SPECIFICATION Coil former material polyamide (PA6.6), glass reinforced, flame retardant in accordance with UL 94-HB ; UL file number E41613(M) Maximum operating temperature 12 C handbook, full pagewidth 2.1 max CBW max. 17 min. 19 Fig.2 E3/15/7 coil former. WINDING DATA FOR E3/15/7 COIL FORMER WITHOUT PINS (E) NUMBER OF SECTIONS WINDING AREA (mm 2 ) MINIMUM WINDING WIDTH (mm) AVERAGE LENGTH OF TURN (mm) CP-E3/15/7-1S 22 Feb 1 5

6 E3/15/7 GENERAL DATA FOR 1-PINS E3/15/7 COIL FORMER PARAMETER Coil former material Pin material Maximum operating temperature Resistance to soldering heat Solderability SPECIFICATION phenolformaldehyde (PF), glass reinforced, flame retardant in accordance with UL 94V- ; UL file number E167521(M) copper-tin alloy (CuSn), tin-lead alloy (SnPb) plated 18 C, IEC 685, class H IEC , Part 2, Test Tb, method 1B: 35 C, 3.5 s IEC , Part 2, Test Ta, method 1: 235 C, 2 s (17.1 min.) max ± max max. CBW Fig.3 E3/15/7 coil former; 1-pins. WINDING DATA FOR 1-PINS E3/15/7 COIL FORMER (E) NUMBER OF NECTIONS WINDING AREA (mm 2 ) MINIMUM WINDING WIDTH (mm) AVERAGE LENGTH OF TURN (mm) CSH-E3/7-1S-1P 22 Feb 1 6

7 E3/15/7 MOUNTING PARTS General data and ordering information ITEM REMARKS FIGURE Clasp CuZn alloy, Ni plated 4 CLA-E3/15/7 Spring stainless steel (CrNi) 5 SPR-E3/15/ min ± (2 ) 5 ;; ;; ;; 28 CBW ± max. CBW35 Fig.4 E3/15/7 clasp. Fig.5 E3/15/7 spring. 22 Feb 1 7

8 E3/15/7 DATA SHEET STATUS DEFINITIONS DATA SHEET STATUS Preliminary specification PRODUCT STATUS Development DEFINITIONS This data sheet contains preliminary data. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Product specification Production This data sheet contains final specifications. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. DISCLAIMER Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Ferroxcube customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Ferroxcube for any damages resulting from such application. PRODUCT STATUS DEFINITIONS STATUS INDICATION DEFINITION Prototype Design-in Preferred Support These are products that have been made as development samples for the purposes of technical evaluation only. The data for these types is provisional and is subject to change. These products are recommended for new designs. These products are recommended for use in current designs and are available via our sales channels. These products are not recommended for new designs and may not be available through all of our sales channels. Customers are advised to check for availability. 22 Feb 1 8