P I M. Low PIM, High-Power Filter Solutions for Monitoring Broadband Emissions. Features: Broadband PIM Monitoring. General Concept for Low PIM ATE
|
|
|
- Ross McKinney
- 6 years ago
- Views:
Transcription
1 Features: Patent pending solution enables monitoring of PIM (Passive IM) up to 13 GHz, with high-power capabilities Near end monitoring: carriers are rejected -90 db by the notch filter and travel through the bandpass filter, into the low PIM termination Far end monitoring: carriers are rejected -90 db by the highpass filter (patent pending), whereas IM products permitted through are monitored by the spectrum analyzer Test set capable to withstand 100 C and 1 K peak Low-PIM 50 ohm Termination Broadband Emission Broadband PIM Monitoring Spurious Emission General Concept for Low PIM ATE BP1 BR1 SPnT BP2 BR2 SPnT S/A BPn BR3
2 PIM: The diplexers are available in three PIM levels: -110 dbc (no dash), -130 dbc (-1) and -156 dbc(-2). The third product is measured at the Bandreject port when two +43 dbm carriers are present at the common port in the passband of the Bandpass filter. P/N F1 F2 F3 F4 F5 BR- Insertion BP- Insertion SD SD SD SD SD SD SD SD SD SD SD SD SD SD SD SD SD SD-00594* SD-00599* SD SD SD SD SD SD SD SD SD SD BR- Return Loss: -10 dbr BP- Return Loss: -15 dbr * -70 db Rejection instead of -90 db
3 PIM: The diplexers are available in three PIM levels: -110 dbc (no dash), -130 dbc (-1) and -156 dbc(-2). The third product is measured at the Bandreject port when two +43 dbm carriers are present at the common port in the passband of the Bandpass filter. P/N F1 F2 F3 F4 F5 BR- Insertion BP- Insertion SD SD SD SD SD SD SD SD-00694* SD-00695* SD SD SD-00732* SD SD SD SD SD BR- Return Loss: -10 dbr BP- Return Loss: -15 dbr * - 75 db Rejection for both BPF and BRF
4 Bandpass/Bandstop Results
5 PIM: The diplexers are available in three PIM levels: -100 dbc (no dash), -130 dbc (-1) and -156 dbc (-2). The third IM product is measured at the common port when two +43 dbm carriers are present at the Lowpass port and/or the Highpass port, with an adjacent port terminated. P/N F1 F2 F3 LP- Insertion LP- Return Loss (dbr) HP- Insertion HP- Return Loss (dbr) SD SD SD-00613* SD * -70 db Rejection instead of -90 db Highpass/Lowpass Examples
6 PIM-Reflection Mode (1) Set-Up is self tested without the need for expensive PIM Analyzer. PIM-Reflection Mode (2) Filters are self tested for PIM without the need for an expensive PIM analyzer.
7 PIM-Through Mode (1) Iso-Coupler Allows broadband sweeping of Tx signals Amps need to provide 3 db more gain Tx Filter needs to reject IM products and be very clean PIM-Through Mode (2) Iso-Diplexer Allows narrowband sweeping of Tx signals Amps do not need to provide 3 db more gain Tx Filters are easier to make (narrower) only junction area is PIM sensitive.
Objectives Typical IMD Levels and Applications Emission Monitoring Solutions Measuring without Disrupting
Objectives Typical IMD Levels and Applications Emission Monitoring Solutions Measuring without Disrupting Low PIM Filtering Solutions - Building Blocks for Reducing Uncertainty of Measurement High-Pass/Low-Pass
Cavity Filters. Waveguide Filters
Cavity Cavity Filters K&L Microwave s series of cavity filters covers the frequency range from 30 MHz to 40 GHz. These filters are available with 2 to 17 resonant sections and bandwidths from 0.2% to 50%.
ytivac Cavity Filters
Cavity Cavity Filters K&L Microwave s series of cavity filters covers the frequency range from 30 MHz to 40 GHz. These filters are available with 2 to 17 resonant sections and bandwidths from 0.2% to 50%.
Demo Circuit DC550A Quick Start Guide.
May 12, 2004 Demo Circuit DC550A. Introduction Demo circuit DC550A demonstrates operation of the LT5514 IC, a DC-850MHz bandwidth open loop transconductance amplifier with high impedance open collector
Analog Filters D R. T A R E K T U T U N J I P H I L A D E L P H I A U N I V E R S I T Y, J O R D A N
Analog Filters D. T A E K T U T U N J I P H I L A D E L P H I A U N I V E S I T Y, J O D A N 2 0 4 Introduction Electrical filters are deigned to eliminate unwanted frequencies Filters can be classified
TOKYO KEIKI RF Filters
Description TOKYO KEIKI offers customized lumped element filters and switched filter banks to >20GHz in compact size packaging. Best-in-class filter performance is achieved by precise control of capacitance
3H Communication. Filters, Multiplexers, Switch Filter Banks and RF Front-End Assemblies. Relentless Innovations. Systems
Relentless Innovations Filters, Multiplexers, Switch Filter Banks and RF Front-End Assemblies Vision We understand that highest quality is achieved when quality is designed in and this often will lead
SOCIETY OF CABLE TELECOMMUNICATIONS ENGINEERS INC
SOCIETY OF CABLE TELECOMMUNICATIONS ENGINEERS INC ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE 151 2008 Mechanical, Electrical, and Environmental Requirements
3H Communication. Systems. RF Filters & Front-End Systems Experts
Relentless Innovations Amplitude 5f1-4f2 4f1-3f2 3f1-2f2 2f1-f2 f1 f2 2f2-f1 3f2-2f1 4f2-3f1 5f2-4f1 Frequency 0 0-10 -20-10 -30-40 -20-50 -60-30 -70-80 -40-90 -100-50 1685 1710 1735 1760 1785 1810 1835
Combined Band MHz. Fig. 1 Typical Diplexer Filter Combiner Fig. 2 Typical Diplexer Combiner
Choosing the Best Power Divider for the Task of Signal Combining As systems become more and more complex, choosing how best to combine two or more RF signals has become a far more difficult question to
Networks International Corp. NIC Overview NETWORKS INTERNATIONAL CORPORATION. P: (913) F: (913)
Networks International Corp. NIC Overview Company Profile Mission: To develop strategic partnerships with our customers to transfer value and innovation through engineering, design, production and continuous
ponents Com ped Lum Lumped Components
Lumped Components Lumped Components K&L Microwave offers Lumped Component filters with a broad selection of frequencies, topologies, and mechanical configurations. Use of standard packages has enabled
LTCC Components. ShenZhen Sunlord Electronics CO., LTD.
LTCC Components Content 1 The concept of LTCC About LTCC technology 2 Sunlord LTCC components Multilayer chip Antenna Multilayer chip Filter Multilayer chip Diplexer Multilayer chip Balun Multilayer chip
A n I/Q modulator is frequently used in
A Simplified Subharmonic I/Q Modulator This passive vector modulator uses opposite polarity diode pairs for frequency doubling to extend the range of operation By Ian Doyle M/A-COM Eurotec Operations A
Part B. Simple Digital Filters. 1. Simple FIR Digital Filters
Simple Digital Filters Chapter 7B Part B Simple FIR Digital Filters LTI Discrete-Time Systems in the Transform-Domain Simple Digital Filters Simple IIR Digital Filters Comb Filters 3. Simple FIR Digital
Lecture 17 Date: Parallel Resonance Active and Passive Filters
Lecture 17 Date: 09.10.2017 Parallel Resonance Active and Passive Filters Parallel Resonance At resonance: The voltage V as a function of frequency. At resonance, the parallel LC combination acts like
CHAPTER 7 CONCLUSION AND FUTURE WORK
132 CHAPTER 7 CONCLUSION AND FUTURE WORK 7.1 CONCLUSION In this research, UWB compact BPFs, single and dual notch filters, reconfigurable filter are developed in microstrip line using PCB technology. In
Low Loss Combiner LLC-1900-IN DATA SHEET. Overview
DATA SHEET Combines Multiple Technologies onto a Single Feed Line Low Loss Combining Combining for Multiple Technologies (GSM/UMTS, UMTS/UMTS, UMTS/LTE, CDMA/LTE, etc.) Minimal or No Guard Band High Reliability
TETRA Tx Test Solution
Product Introduction TETRA Tx Test Solution Signal Analyzer Reference Specifications ETSI EN 300 394-1 V3.3.1(2015-04) / Part1: Radio ETSI TS 100 392-2 V3.6.1(2013-05) / Part2: Air Interface May. 2016
Multi-function Site Passive Intermodulation Analyzer.
Multi-function Site Passive Intermodulation Analyzer www.rosenbergerap.com 01 Introduction Rosenberger HQ, Bavaria, Germany 01 A Rosenberger Hochfrequenztechnik GmbH&Co. was founded in Germany in 1958
AMERICAN NATIONAL STANDARD
ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE 151 2015 Mechanical, Electrical, and Environmental Requirements for RF Traps and Filters NOTICE The Society of
RB-NKC1 3dB Hybrid Coupler - CDMA800/GSM900, MHz
Hybrid Couplers RB-NKC1 3dB Hybrid Coupler - CDMA800/GSM900, 800-960MHz High input power of 200W. Permits combining of CDMA800 and GSM900 services. Low insertion loss of 0.15dB. High inter-band isolation
Measurement of Digital Transmission Systems Operating under Section March 23, 2005
Measurement of Digital Transmission Systems Operating under Section 15.247 March 23, 2005 Section 15.403(f) Digital Modulation Digital modulation is required for Digital Transmission Systems (DTS). Digital
S.A. Torchinsky, A. van Ardenne, T. van den Brink-Havinga, A.J.J. van Es, A.J. Faulkner (eds.) 4-6 November 2009, Château de Limelette, Belgium
WIDEFIELD SCIENCE AND TECHNOLOGY FOR THE SKA SKADS CONFERENCE 29 S.A. Torchinsky, A. van Ardenne, T. van den Brink-Havinga, A.J.J. van Es, A.J. Faulkner (eds.) 4-6 November 29, Château de Limelette, Belgium
Keywords: ISM, RF, transmitter, short-range, RFIC, switching power amplifier, ETSI
Maxim > Design Support > Technical Documents > Application Notes > Wireless and RF > APP 4929 Keywords: ISM, RF, transmitter, short-range, RFIC, switching power amplifier, ETSI APPLICATION NOTE 4929 Adapting
EE301 ELECTRONIC CIRCUITS
EE30 ELECTONIC CICUITS CHAPTE 5 : FILTES LECTUE : Engr. Muhammad Muizz Electrical Engineering Department Politeknik Kota Kinabalu, Sabah. 5. INTODUCTION Is a device that removes or filters unwanted signal.
Design of a BAW Quadplexer Module Using NI AWR Software
Application Note Design of a BAW Quadplexer Module Using NI AWR Software Overview With the development of the LTE-Advanced and orthogonal frequency division multiple access (OFDMA) techniques, multiple
Major Products. RF/Microwave provider
Major Products Products 1 RF Sub-systems Combiner FEU TTA TMA SCU 2 Products 2 RF components Power Splitter (BTS) Filter Switch Coupler 3 Feature1 Divider Frequency Range 824~894, 1750~1870, 1885~2170,
Best-in-industry performance. Radar. Communication. Electronic Counter Measures. Laboratory Instrumentation. Commercial and military products
Best-in-industry performance Radar Communication Electronic Counter Measures Laboratory Instrumentation Commercial and military products YIG Filters and Oscillators YIG Products from Teledyne Microwave
Introduce cascaded first-order op-amp filters. Faculty of Electrical and Electronic Engineering
Yıldız Technical University Cascaded FirstOrder Filters Introduce cascaded first-order op-amp filters Faculty of Electrical and Electronic Engineering Lesson Objectives Introduce cascaded filters Introduce
Series CCS-19 Multi-Throw DC-2 GHz Latching Coaxial Switch
PART NUMBER CCS-19 CS-19 DESCRIPTION Commercial Latching Multi-throw, DC-2GHz, with N or TNC connectors Elite Latching Multi-throw, DC-2GHz, with N or TNC connectors The CCS-19/CS-19 is a broadband, multi-throw,
Filters / Duplexers / Diplexers / RF Assemblies. Commercial, Military and Wireless filter products
Filters / Duplexers / Diplexers / RF Assemblies Commercial, Military and Wireless filter products Excellence in Filter Technologies for the Military, Commercial and Wireless Markets Table of Contents INTRODUCTION
Multi-Function Assemblies
K&L Microwave offers a variety of (MFA) products to satisfy a broad range of filtering applications. Many applications require frequency pre-selection at the front end of the communication or test and
Thank you Carmina. Welcome all to our presentation of Direct Filter Synthesis for Customized Response
Thank you Carmina. Welcome all to our presentation of Direct Filter Synthesis for Customized Response 1 This is just a brief review of our agenda, first we will review the Functions and types of filters
Series CCR-48K/CR-48K Multi-Throw DC 40 GHz Normally Open Coaxial Switch
COAX SWITCHES Series CCR-48K/CR-48K PART NUMBER CCR-48K CR-48K DESCRIPTION Commercial Normally Open Multi-throw, DC-40GHz Elite Normally Open Multi-throw, DC-40GHz The CCR-48K/CR-48K is a broadband, multi-throw,
Series CCS-47/CS-47 High Power DC 12 GHz Failsafe TRANSFER Coaxial Switch
COAX SWITCHES Series CCS-47/CS-47 PART NUMBER CCS-47 CS-47 DESCRIPTION Commercial Failsafe TRANSFER, DC-GHz Elite Failsafe TRANSFER, DC-GHz The CCS-47/CS-47 is a long-life high performance transfer switch
Broadcast - Filters & Components Table of Contents
Broadcast - Filters & Components Table of Contents Model Description Page Ordering & Warranty Information 2 About the Company 3 17720 LTE Bandstop Filters 4 17890 LTE Block (A, B or C) Bandpass Filters
Series CCS-47/CS-47 High Power DC 12 GHz Latching TRANSFER Coaxial Switch
PART NUMBER CCS-47 CS-47 DESCRIPTION Commercial Latching TRANSFER, DC-GHz Elite Latching TRANSFER, DC-GHz The CCS-47/CS-47 is a long-life high performance transfer switch designed for use in 5 Ohms coaxial
ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE
ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE 115 2011 Test Method for Reverse Path (Upstream) Intermodulation Using Two Carriers NOTICE The Society of Cable
CAVITY TUNING. July written by Gary Moore Telewave, Inc. 660 Giguere Court, San Jose, CA Phone:
CAVITY TUNING July 2017 -written by Gary Moore Telewave, Inc 660 Giguere Court, San Jose, CA 95133 Phone: 408-929-4400 1 P a g e Introduction Resonant coaxial cavities are the building blocks of modern
For detailed specifications or for your custom application, please contact your K&L sales representative. 20 db High Power Attenuator
DAS Overview As the LTE rollout continues and cellular frequency bands grow more congested, continuity of coverage becomes more challenging. Distributed Antenna Systems (DAS) provide one way to increase
ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE
ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE 82 2012 Test Method for Low Frequency and Spurious Disturbances NOTICE The Society of Cable Telecommunications
Part Numbering System
Reactel Filters can satisfy a variety of filter requirements. These versatile units cover the broad frequency range of 2 khz to 5 GHz, and are available in either tubular or rectangular packages, connectorized
Radiated Spurious Emission Testing. Jari Vikstedt
Radiated Spurious Emission Testing Jari Vikstedt jari.vikstedt@ets-lindgren.com What is RSE? RSE = radiated spurious emission Radiated chamber Emission EMI Spurious intentional radiator 2 Spurious Spurious,
2-6 GHz Broadband 4-Watt Power Amplifiers. One Product. Multiple Solutions.
2-6 GHz Broadband 4-Watt Power Amplifiers One Product. Multiple Solutions. Spectrum Microwave There is a new microwave technology leader with a proven track record in military and commercial applications...
MFJ-722 INSTRUCTIONS
MFJ-722 INSTRUCTIONS INTRODUCTION I The MFJ-722 OPTIMIZER consists of a tunable notch filter combined with a switch selectable highpass/lowpass filter (SSB) and bandpass (CW) filter. This filtering capability
REFLECTIONLESS FILTERS
NEW! Two & Three Section Models MMIC REFLECTIONLESS FILTERS 50Ω DC to 21 GHz The Big Deal High Stopband rejection, up to 50 db Patented design terminates stopband signals Pass band cut-off up to 11 GHz
Electric Circuit Theory
Electric Circuit Theory Nam Ki Min nkmin@korea.ac.kr 010-9419-2320 Chapter 15 Active Filter Circuits Nam Ki Min nkmin@korea.ac.kr 010-9419-2320 Contents and Objectives 3 Chapter Contents 15.1 First-Order
Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK 17 Product Application Notes Introduction
RF, Microwave & Wireless. All rights reserved
RF, Microwave & Wireless All rights reserved 1 Non-Linearity Phenomenon All rights reserved 2 Physical causes of nonlinearity Operation under finite power-supply voltages Essential non-linear characteristics
Protection criteria for arrival time difference receivers operating in the meteorological aids service in the frequency band 9-11.
Recommendation ITU-R RS.1881 (02/2011) Protection criteria for arrival time difference receivers operating in the meteorological aids service in the frequency band 9-11.3 khz RS Series Remote sensing systems
REFLECTIONLESS FILTERS
NEW! Two & Three Section Models MMIC REFLECTIONLESS FILTERS 50Ω DC to 21 GHz The Big Deal High Stopband rejection, up to 50 db Patented design terminates stopband signals Pass band cut-off up to 11 GHz
REMARKS The customer has ordered two measurements mentioned above according to the standard EN
Type: Alignment range: Switching range: SATELLINE-3ASm/250/LC 380,000-470,000 MHz One channel Equipment 1 and 2 Equipment Equipment Measurement Serial no. 033322036 and 033322037 Serial no. Serial no.
Series CCRT-53S/CRT-53S Internal 50Ω Termination DC-26.5 GHz Failsafe SPDT Coaxial Switch
COAX SWITCHES Series CCRT-53S/CRT-53S PART NUMBER CCRT-53S CRT-53S DESCRIPTION Commercial Failsafe SPDT, DC-26.5GHz, Internal 5Ω Termination Elite Failsafe SPDT, DC-26.5GHz, Internal 5Ω Termination The
Millimeter Wave Spectrum Analyzer with Built-in >100 GHz Preselector
Millimeter Wave Spectrum Analyzer with Built-in >1 GHz Preselector Yukiyasu Kimura, Masaaki Fuse, Akihito Otani [Summary] Fifth-generation (5G) mobile communications technologies are being actively developed
Series CCP-47N Low PIM DC 3 GHz Latching TRANSFER Coaxial Switch
COAX SWITCHES Series CCP-47N PART NUMBER CCP-47N DESCRIPTION Commercial Latching TRANSFER, DC-3GHz, Low PIM These switches are designed to have extremely low passive intermodulation for use in narrow bandwidth
REFLECTIONLESS FILTERS
NEW! Two & Three Section Models MMIC REFLECTIONLESS FILTERS 50Ω DC to 21 GHz The Big Deal High Stopband rejection, up to 50 db Patented design terminates stopband signals Pass band cut-off up to 11 GHz
MINIMIZING SITE INTERFERENCE
MINIMIZING SITE INTERFERENCE CHAPTER 8 This chapter provides information on preventing radio frequency (RF) interference at a communications site. The following topics are included: Interference Protection
bringing technology to life
bringing technology to life For four decades, orch Microwave has continuously supplied RF and Microwave components and systems to the leading military, industrial, and commercial manufacturers worldwide.
Superheterodyne Receiver Tutorial
1 of 6 Superheterodyne Receiver Tutorial J P Silver E-mail: john@rfic.co.uk 1 ABSTRACT This paper discusses the basic design concepts of the Superheterodyne receiver in both single and double conversion
Filter Products Guide
Filter Products Guide World Leaders in the Design and Manufacture of RF and Microwave Filter Products World Leaders in Filter and BSC Filters specialise in the design and manufacture of Microwave filters,
Series CCRT-33S/CRT-33S Internal 50Ω Termination DC 18 GHz/DC-22 GHz Failsafe SPDT Coaxial Switch
COAX SWITCHES Series CCRT-33S/CRT-33S PART NUMBER CCRT-33S CRT-33S DESCRIPTION Commercial Failsafe SPDT, DC-18GHz, Internal 50Ω Termination Elite Failsafe SPDT, DC-22GHz, Internal 50Ω Termination The CCRT-33S/CRT-33S
3-2 Measurement of Unwanted Emissions of Marine Radar System
3 Research and Development of Testing Technologies for Radio Equipment 3-2 Measurement of Unwanted Emissions of Marine Radar System Hironori KITAZAWA and Sadaaki SHIOTA To consider the effective use of
An Application of Bandpass Filters. Jeff Crawford - K ZR October 15, 2016
An Application of Bandpass Filters Jeff Crawford - K ZR October 15, 2016 1 Goals for this Discussion: Cover some general filter theory Apply this theory to an amateur radio need SO2R (Single Operator 2
Series CCRT-33S/CRT-33S Internal 50Ω Termination DC 18 GHz/DC-22 GHz Latching SPDT Coaxial Switch
COAX SWITCHES Series CCRT-33S/CRT-33S PART NUMBER CCRT-33S CRT-33S DESCRIPTION Commercial Latching SPDT, DC-18GHz, Internal 50Ω Termination Elite Latching SPDT, DC-22GHz, Internal 50Ω Termination The CCRT-33S/CRT-33S
Evaluation of Filter and Amplifier Transmission Characteristics
Product Introduction Evaluation of Filter and Amplifier Transmission Characteristics - Internal Signal Generator Control Function Option (Functions equivalent to tracking generator) Signal Analyzer MS2830A
REFLECTIONLESS FILTERS
NEW! Two & Three Section Models MMIC REFLECTIONLESS FILTERS 50Ω DC to 21 GHz The Big Deal High Stopband rejection, up to 50 db Patented design terminates stopband signals Pass band cut-off up to 11 GHz
Millimeter Wave Product Catalogue VivaTech Consulting S.A.R.L.
VivaTech Consulting S.A.R.L. sales@vivatech.biz Telephone: +33 04 89 01 14 61 Fax: +33 04 93 87 08 66 Table of Contents Millimeter Wave Low Noise Amplifiers VTLNA Series...3 Millimeter Wave Power Amplifiers
Rigol DSA705 Spectrum Analyzer Reviewed by Phil Salas AD5X
Rigol DSA705 Spectrum Analyzer Reviewed by Phil Salas AD5X ad5x@arrl.net Today s state-of-the-art test equipment is becoming more and more affordable. Spectrum analyzers, however, have stayed above the
Options and their applications Extensions for basic model OCXO Reference Oscillator For long-term stability OCXO Reference Oscillator For extremely high long-term stability Duplex Modulation Meter Allows
Frequency Doubler 3,2 6,4 GHz to 6,2 12,8 GHz based on HMC204MS
Frequency Doubler 3,2 6,4 GHz to 6,2 12,8 GHz based on HMC204MS Matthias, DD1US, January 4 th 2018, Rev 3.0 Hello, as I just finished refurbishing a R&S SMIQ06 signal generator, which covers the frequency
Components for modular microwave transverters. Wolf-Henning Rech DF9IC in JN48iw
Components for modular microwave transverters Wolf-Henning Rech DF9IC in JN48iw http://www.df9ic.de Content Multiband transverter systems Filters and multiplexers PLL-disciplined oscillators Transverters
Series CCR-58S/CR-58S Multi-Throw DC 26.5 GHz Normally Open Coaxial Switch
PART NUMBER CCR-58S CR-58S DESCRIPTION Commercial Normally Open Multi-throw, DC-6.5GHz Elite Normally Open Multi-throw, DC-6.5GHz The CCR-58S/CR-58S is a broadband, multi-throw, electromechanical coaxial
Series CCS-37S/CS-37S Miniature DC 18 GHz Failsafe TRANSFER Coaxial Switch
COAX SWITCHES Series CCS-37S/CS-37S PART NUMBER CCS-37S CS-37S DESCRIPTION Commercial Failsafe TRANSFER, DC-8GHz Elite Failsafe TRANSFER, DC-8GHz The CCS-37S/CS-37S is a long-life high performance transfer
OPEN TEM CELLS FOR EMC PRE-COMPLIANCE TESTING
1 Introduction Radiated emission tests are typically carried out in anechoic chambers, using antennas to pick up the radiated signals. Due to bandwidth limitations, several antennas are required to cover
REFLECTIONLESS FILTERS
NEW! Two & Three Section Models MMIC REFLECTIONLESS FILTERS 50Ω DC to 21 GHz The Big Deal High Stopband rejection, up to 50 db Patented design terminates stopband signals Pass band cut-off up to 11 GHz
Catalog #128 FILTEK. RF & Microwave Filters
atalog #128 FILTEK FILTEK ontents Terms and onditions of Sale: General Ordering Information Page 3 Model Numbering System Page 4 Glossary Page General Performance Page 8 onnecr Types Page 12 BANDPASS:
Air Band Multicoupling Products MHz MHz
Air Band Multicoupling Products 118-137 MHz 225-400 MHz AFL Proposal Page: 1 of 12 Air Band Cavity Filters Key Features Low Insertion Loss Easy to install 19 Rack Mount High isolation TX-TX MTBF > 500,000
Series CCR-33K/CR-33K Miniature DC 33.5 GHz Failsafe SPDT Coaxial Switch
PART NUMBER CCR-33K CR-33K DESCRIPTION Commercial Failsafe SPDT, DC-33.5GHz Elite Failsafe SPDT, DC-33.5GHz The CCR-33K/CR-33K is a broadband, SPDT, electromechanical, coaxial switch designed to switch
Series CCT-58S/CT-58S Multi-Throw DC-26.5 GHz Normally Open Coaxial Switch
COAX SWITCHES Series CCT-58S/CT-58S PART NUMBER CCT-58S CT-58S DESCRIPTION Commercial Normally Open Multi-throw, DC-26.5GHz Elite Normally Open Multi-throw, DC-26.5GHz The CCT-58S/CT-58S is an internally
Design and Manufacturing of RF and Electronic Equipment
Design and Manufacturing of RF and Electronic Equipment Rantelon Ltd. Company presentation September 2012 Agenda History Competence Tools and Instruments Staff Reseach activities Products and Services
Spectrum Sharing 900 MHz Combiner
DATA SHEET Combines two 900 MHz base station outputs with a narrow guard band onto a common port Full transmit and receive band combining with a guard band of 0.8 to 3 MHz High power 400 W per input port
RS3400W/04 77 GHz Radar Sensor
Features Complete 76-77GHz band FMCW Radar Front End Synthesized frequency source Wideband Sweep Description The RS34W/4 is a W-band FMCW radar front end featuring synthesized frequency sweeps. A fast
How to calibrate the VNWA sensitivity in Spectrum Analyzer mode
How to calibrate the VNWA sensitivity in Spectrum Analyzer mode Preface: When using the VNWA as spectrum Analyzer (SA) the sensitivity is varying as function of frequency. This because the LO DDS feed
BROADBAND DROP AMPLIFIER
BDA BROADBAND DROP AMPLIFIER FEATURES 1 GHz Gallium Arsenide Technology 2.5 db Noise Figure Patented Auto-Seize P-Series F- Connector One, Two or Four Port Versions Two-Way Capable LED Power Verification
Manufacturers of RF and Microwave Components and Assemblies Specialist in RF Filters, Power amplifiers and RF Switches
Manufacturers of RF and Microwave Components and Assemblies Specialist in RF Filters, Power amplifiers and RF Switches sales@cormic.com www.cormic.com P 724.940.7556 F 724.940.7707 RF & MICROWAVE FILTERS
MAX2105CWI 0 C to +70 C 28 SO 90 /64, /65
19-1256; Rev 2; 1/98 EVALUATION KIT MANUAL FOLWS DATA SHEET Direct-Conversion Tuner ICs for General Description The MAX212/MAX215 are low-cost direct-conversion tuner ICs designed for use in digital direct-broadcast
OPEN TEM CELLS FOR EMC PRE-COMPLIANCE TESTING
1 Introduction Radiated emission tests are typically carried out in anechoic chambers, using antennas to pick up the radiated signals. Due to bandwidth limitations, several antennas are required to cover
Series CCR-33K/CR-33K Miniature DC 33.5 GHz Latching SPDT Coaxial Switch
COAX SWITCHES Series CCR-33K/CR-33K PART NUMBER CCR-33K CR-33K DESCRIPTION Commercial Latching SPDT, DC-33.5GHz Elite Latching SPDT, DC-33.5GHz The CCR-33K/CR-33K is a broadband, SPDT, electromechanical,
Frequency Division Multiplexing and Headend Combining Techniques
Frequency Division Multiplexing and Headend Combining Techniques In the 3 rd quarter technical report for 2010, I mentioned that the next subject would be wireless link calculations and measurements; however,
Series CCT-59S/CT-59S Multi-Throw DC-26.5 GHz Latching Coaxial Switch
PART NUMBER CCT-59S CT-59S DESCRIPTION Commercial Latching Multi-throw, DC-26.5GHz Elite Latching Multi-throw, DC-26.5GHz The CCT-59S/CT-59S is an Internally Terminated broadband, multi-throw, electromechanical
Ave output power ANT 1(dBm) Ave output power ANT 2 (dbm)
Page 41 of 103 9.6. Test Result The test was performed with 802.11b Channel Frequency (MHz) power ANT 1(dBm) power ANT 2 (dbm) power ANT 1(mW) power ANT 2 (mw) Limits dbm / W Low 2412 7.20 7.37 5.248 5.458
Series CCR-39S/CR-39S Multi-Throw DC-18 GHz/DC-22 GHz Latching Coaxial Switch
PART NUMBER CCR-39S CR-39S DESCRIPTION Commercial Latching Multi-throw, DC-8GHz Elite Latching Multi-throw, DC-22GHz The CCR-39S/CR-39S is a broadband, multi-throw, electromechanical coaxial switch designed
Series CCT-58S/CT-58S Multi-Throw DC-26.5 GHz Normally Open Coaxial Switch
COAX SWITCHES Series CCT-58S/CT-58S PART NUMBER CCT-58S CT-58S DESCRIPTION Commercial Normally Open Multi-throw, DC-26.5GHz Elite Normally Open Multi-throw, DC-26.5GHz The CCT-58S/CT-58S is an internally
INTRODUCTION TO FILTER CIRCUITS
INTRODUCTION TO FILTER CIRCUITS 1 2 Background: Filters may be classified as either digital or analog. Digital filters are implemented using a digital computer or special purpose digital hardware. Analog
Series CCT-38S/CT-38S Multi-Throw DC 18 GHz/DC-22 GHz Normally Open Coaxial Switch
COAX SWITCHES Series CCT-38S/CT-38S PART NUMBER CCT-38S CT-38S DESCRIPTION Commercial Normally Open Multi-throw, DC-18GHz Elite Normally Open Multi-throw, DC-22GHz The CCT-38S/CT-38S is an internally terminated,
Series CCR-33S/CR-33S Miniature DC 18 GHz/DC-22 GHz Failsafe SPDT Coaxial Switch
COAX SWITCHES Series CCR-33S/CR-33S PART NUMBER CCR-33S CR-33S DESCRIPTION Commercial Failsafe SPDT, DC-18GHz Elite Failsafe SPDT, DC-22GHz The CCR-33S/CR-33S is a broadband, SPDT, electromechanical, coaxial
Series CCR-33K/CR-33 K Miniature DC 33.5 GHz Failsafe SPDT Coaxial Switch
PART NUMBER CCR-33K CR-33K DESCRIPTION Commercial Failsafe SPDT, DC-33.5GHz Elite Failsafe SPDT, DC-33.5GHz The CCR-33K/CR-33K is a broadband, SPDT, electromechanical, coaxial switch designed to switch
Series CCR-53S/CR-53S Miniature DC 26.5 GHz Latching SPDT Coaxial Switch
PART NUMBER CCR-53S CR-53S DESCRIPTION Commercial Latching SPDT, DC-26.5GHz Elite Latching SPDT, DC-26.5GHz The CCR-53S/CR-53S is a broadband, SPDT, electromechanical, coaxial switch designed to switch
Electronic PRINCIPLES
MALVINO & BATES Electronic PRINCIPLES SEVENTH EDITION Chapter 21 Active Filters Topics Covered in Chapter 21 Ideal responses Approximate responses Passive ilters First-order stages VCVS unity-gain second-order