Section 24. Capacitors, Arresters and Harmonic Filters. BuyLog Catalog 24-1

Transcription

1 Capacitors, Arresters and Harmonic Filters Section 4 Line/Load Reactorsup to V...4- Line/Load ReactorsThree-phase Reactors Matrix Series D Harmonic Filters Protective Capacitors for AC Rotating Machines...4- Fixed Motor and Pump Capacitors...4- Fixed Low Voltage Power Factor Correction Capacitors Fixed Low Voltage Power Factor Correction with Harmonic Filter Equipment Automatic Fast-Switching LV Power Factor Correction Capacitors Automatic LV Power Factor Correction Capacitors Automatic LV Power Factor Correction Capacitors and Harmonic Filter Equipment...4- Active Harmonic Filter Fixed MV Power Factor Correction Capacitors High Voltage Capacitor Units, Singleand Three-Phase High Voltage Pole-Mounted, Open Stack-Rack and Metal Enclosed Equipment OEM High Energy Surge Protectors Tranquell Motor Surge Protectors Motor and Generator Surge Protection Equipment Secondary Surge Arresters and Protective Capacitors Series 9L5F HV Station ArrestersPolymer and Porcelain...4- HV Intermediate ArrestersPolymer Station and Intermediate ArrestersOutline Drawings Station and Intermediate Class ArrestorsAccessories Distribution and Riser Pole Arresters Web Site: For more information on these products, visit our Web Site or order publications listed below. Order From: GE Attn: Distribution Services 60 GE Road Bloomington, IL 6704 Phone: (Dial Comm 8*5-45) Fax: (Dial Comm 8*5-45) Reference Publications Capacitors GEP-974G, DEA-6 GEP-974G, DEA-6 GEP-974G, DEA-6 GEP-974G, DEA-6 DEA-98 GEP-974G, DEA-, DEA-6 DEA-6 DEA-, DEA-4 DEA-4 Arresters GED-7060A FETA-00A Motor and Pump Capacitors, 40 and 480 Volts Fixed Low Voltage Power Factor Correction Capacitors, 40, 480 and Volts Automatically Switched, LV Power Factor Correction Capacitors, 40, 480 and Volts Automatically Switched Harmonic Filters, 40, 480 and Volts GEMATIC Quick Response Medium Voltage Volts, Type HWT High Voltage Single-Phase Capacitors, -, Volts High Voltage Pole Top and Open Stack Rack Equipment Protective Capacitors for AC Rotating Machines Tranquell Secondary Surge Arresters and Protective Capacitor Product Selection and Application Guide Harmonic Filters GEH-756 DET-76 FETR-00 Matrix D Harmonic Filter GEMACTIVE Harmonic Filter AC Line/Load Reactors Rev. / BuyLog Catalog 4-

2 Capacitors, Arresters and Harmonic Filters Section 4 Line/Load Reactors Up to V Motor Protection Reactors help to protect motors from the high peak voltages and fast rise times (dv/dt) which can be experienced in IGBT inverter applications when the distance between the inverter and motor is long. Harmonic Reduction Because all standard GE Line/Load reactors are compensated for harmonics (current and frequency), they are extremely effective at reducing the amount of harmonics which are produced by a drive/inverter. Use 5% impedance, harmonic compensated reactors for best reaction of harmonic distortion. Voltage Spike Protection A % impedance reactor is very effective at protecting against damage to or nuisance tripping of AC voltage source inverters, due to voltage spikes. Voltage spikes on the AC power lines cause elevation of the DC Bus voltage which may cause the inverter to trip-off and indicate an over-voltage protection condition. Use reactors to absorb these line spikes and offer protection to the rectifiers and DC Bus capacitors while minimizing nuisance tripping of the inverter. Cabinet Product Number NEMA Enclosure Style Type CAB8 CABV CAB7V CAB6C CAB-8 CAB-V CAB-7V CAB-6C Wall Mount Floor Floor Floor Outline Dimensions Exact terminal configuration may be different than shown. For exact terminal configuration contact factory for outline drawing. W H D Wgt (lbs.) Typical Harmonic Distortion of PWM Inverter Without Reactor Agency Approvals GE line reactors are UL recognized. All UL approvals are for USA and Canada. UL-6 File #E9687 ( amp-00 amps) UL-8 File #E9686 ( amp-00 amps) All higher currents offer UL recognized insulation systems and construction. CE Marked With 5% Impedance Reactor NEMA Cabinets All GE Line/Load Reactors are available as either open type or in a NEMA Type general purpose enclosure. To order a reactor mounted in a cabinet simply change the second to last digit of the product number from 0 to. Example 0080 becomes 008. For more product information, go to click on Products and Services and then Products. 4- BuyLog Catalog Rev. /

3 Capacitors, Arresters and Harmonic Filters Line/Load Reactors Up to V Section 4 Selection Table* Volts, /60 Hertz (open Type) Ratings HP/kw /.75.5/. /.5 /. 5/.7 7.5/5.5 0/7.5 5/ 0/5 5/8.5 0/ 40/0 08 Volts % Impedance /60 HZ 5% Impedance Volts % Impedance /60 HZ 5% Impedance Volts % Impedance /60 HZ 4% Impedance G Volts % Impedance /60 HZ 4% Impedance Volts % Impedance /60 HZ 4% Impedance Volts % Impedance /60 HZ 5% Impedance Volts % Impedance /60 HZ 5% Impedance *For maximum continuous current ratings refer to Specifications on next page. Ratings HP/kw /7.5 60/45 75/55 00/75 5/9 / 00/ /87 00/5 /6 /00 0/75 /4 7/5 08 Volts % Impedance 000B4 0B4 00B4 0B /60 HZ 5% Impedance 000B4 0B4 00B4 0B Volts % Impedance B4 0B4 00B4 0B /60 HZ 5% Impedance B4 0B4 00B4 0B Volts % Impedance B4 0B4 00B4 0B4 0B /60 HZ 4% Impedance B4 0B4 00B4 0B4 0B Volts % Impedance B4 0B4 00B4 00B4 0B /60 HZ 4% Impedance B4 0B4 00B4 00B4 0B Volts % Impedance B4 000B4 0B4 00B4 0B /60 HZ 4% Impedance B4 000B4 0B4 00B4 0B Volts % Impedance B4 0B4 00B4 0B /60 HZ 5% Impedance B4 0B4 00B4 0B Volts % Impedance B4 0B4 00B4 0B4 0B /60 HZ 5% Impedance B4 0B4 00B4 0B4 0B Consult Factory For Input or Output of Adjustable Speed Drive/Inverter Systems *For higher or lower current ratings, consult factory. *For other voltages or frequencies, consult factory. Single phase reactors are also available, consult factory for proper selection. This table is suitable for selection of both input and output reactors because their harmonic compensation and IGBT protection allow them to be used in either application. Specific current and inductance ratings are indicated on next page. Consult factory for any special applications (higher current, motor rating different than controller rating, etc.) Select GE Line/Load reactors based upon motor horsepower, (or kilowatts) and voltage. Verify that the motor full load ampere rating is within the fundamental current rating of the reactor, and the drive/inverter rating is within the maximum continuous rating of the reactor (See next page). Rev. / BuyLog Catalog 4-

4 Capacitors, Arresters and Harmonic Filters Section 4 Line/Load Reactors -Phase Reactors: Line/Load Specifications Table Volts, /60 hz (Open Type) Open Type Product Number 000 Fundamental Amps Max. Amps Inductance.0mh Watts Loss 7.5 A mm/in. /4.4 B mm/in. 0/4.0 C mm/in. 74/.8 D mm/in. /.0 E mm/in. 6/.44 Open Type Wgt. Kg/Lbs..8/4 NEMA Enclosure Style CAB mh. /4.4 0/4.0 74/.9 /.0 6/.44.8/4 CAB mh 6 /4.4 0/4.0 74/.9 /.0 6/.44.8/4 CAB mh 0.7 /4.4 0/4.0 69/.7 44/.7 6/.44.4/ CAB mh 4.5 /4.4 0/4.0 74/.9 /.0 6/.44.8/4 CAB mh 0 /4.4 0/4.0 74/.9 /.0 6/.44./4 CAB mh 0 /4.4 0/4.0 79/. 54/. 6/.44.8/5 CAB mh /4.4 0/4.0 9/.6 66/.6 6/.44.7/6 CAB mh 9.5 5/6.0 /4.8 79/. 54/. /.0./7 CAB mh 9 5/6.0 /4.8 79/. 54/. /.0./8 CAB mh 5. 5/6.0 /4.8 86/.4 6/.5 /.0 5.0/ CAB mh 8 5/6.0 /4.8 86/.4 6/.5 /.0 5.9/ CAB mh 6 5/6.0 /4.8 79/. 54/. /.0 4.0/9 CAB mh 5/6.0 /4.8 79/. 54/. /.0 4.5/0 CAB mh 4 5/6.0 /4.8 94/.7 70/.75 /.0 8./8 CAB mh 6 5/6.0 /4.8 79/. 54/. /.0 4.0/9 CAB mh 4 5/6.0 /4.8 86/.4 5/.5 /.0 5.4/ CAB mh 4 8/7. 45/5.7 97/.8 66/.6 76/.0 7./6 CAB-V mh 48 8/7. 4/5.6 86/.4 60/. 76/.0 5.0/ CAB-V mh 5 8/7. 4/5.6 86/.4 60/. 76/.0 6./4 CAB-V mh 6 8/7. 45/5.7 97/.8 66/.6 76/.0 8./8 CAB-V mh 49 8/7. 4/5.6 97/.8 66/.6 76/.0 6./4 CAB-V mh 54 8/7. 45/5.7 97/.8 66/.6 76/.0 7./6 CAB-V mh 54 9/9.0 78/7.0 /4.8 80/. 76/.0 4/0 CAB-V mh 54 9/9.0 78/7.0 /4.8 80/. 76/.0 0/ CAB-V mh 6 9/9.0 78/7.0 /4.8 80/. 76/.0 /8 CAB-V mh 65 9/9.0 78/7.0 6/5. 9/.6 76/.0 8/9 CAB-V mh 64 9/9.0 78/7.0 /4.8 80/. 76/.0 /4 CAB-V mh 67 9/9.0 78/7.0 /4.8 80/. 76/.0 /7 CAB-V mh 7 9/9.0 78/7.0 4/5.6 99/.9 76/.0 8/4 CAB-V mh 8 74/0.8 08/8. 4/5.6 88/.5 9/.6 9/4 CAB-V mh 86 74/0.8 /8. 4/5.6 88/.5 9/.6 /5 CAB-V mh 96 74/0.8 /8.4 60/6. 7/4.6 8/.6 5/55 CAB-V *To order a reactor mounted in NEMA enclosure simply change the second to last digit of the product number from "0" to "". For more product information, go to click on Products and Services and then Products. 4-4 BuyLog Catalog Rev. /

5 Capacitors, Arresters and Harmonic Filters Line/Load Reactors -Phase Reactors: Line/Load Specifications Table Section 4 Volts, /60 hz (Open Type) Open Type Product Number Fundamental Amps Max. Amps Inductance Watts Loss A mm/in. B mm/in. C mm/in. D mm/in. E mm/in. Open Type Wgt. Kg/Lbs. NEMA Enclosure Style mh 94 74/0.8 /8. 4/5.6 88/.5 9/.6 /47 CAB-V mh 84 74/0.8 08/8. 47/5.8 9/.6 9/.6 /5 CAB-V mh 08 74/0.8 /8.4 60/6. 06/4. 9/.6 /74 CAB-V mh 08 9/9.0 79/7.04 4/4.9 80/.6 76/ /9 CAB-V mh 80 74/0.8 /8.4 7/6.75 9/.66 9/.6 6/57 CAB-V mh 8 74/0.8 /8.4 84/7.5 06/4.6 9/.6 9/64 CAB-V mh 6 74/0.8 /8.4 46/ /.6 9/.6 8/40 CAB-V mh 49 74/0.8 /8.4 5/6 88/.47 9/.6 / CAB-V mh 8 74/0.8 /8.4 8/7. 06/4.6 9/.6 /67 CAB-V 000B mh 4 74/0.8 /8.4 5/6 06/4.6 9/.6 /48 CAB-V 000B mh 68 74/0.8 /8.4 6/8.5 /4.4 9/.6 /67 CAB-V 000B mh 46 74/0.8 67/0.5 7/9.5 /5.9 9/.6 46/00 CAB-V 0B mh 54 74/0.8 08/8.7 84/7.5 06/4.6 9/.6 /68 CAB-V 0B mh 66/4.4 56/4 0/8.5 /5.6 7/4.6 49/06 CAB-7V 0B mh 9 66/4.4 56/4 88/.5 48/5.8 7/4.6 64/40 CAB-7V 00B mh 4 66/4.4 56/4 68/6.6 9/5.07 7/4.6 /0 CAB-7V 00B mh 64 75/ /4 57/0. 49/5.88 7/4.6 57/5 CAB-7V 00B mh 5 66/4.4 56/4 0/ 8/7. 7/4.6 86/90 CAB-7V 0B4 0.00mh 66/4.4 56/4 54/0 /5.6 7/4.6 46/00 CAB-7V 0B mh 94/5.5 56/4 9/.5 7/6.76 7/4.6 7/55 CAB-7V 0B4 0.05mh 9 94/5.5 56/4 68/4.5 84/7.6 7/4.6 9/00 CAB-7V 00B mh 66 94/5.5 56/4 67/0.5 40/5.5 7/4.6 55/0 CAB-7V mh 40 94/5.5 56/4 0/ 7/6.76 7/4.6 8/80 CAB-76C mh 4 94/5.5 56/4 75/ /9.76 7/4.6 /90 CAB-76C mh 07 94/5.5 56/4 79/ 68/6.66 7/4.6 7/60 CAB-76C mh 44 94/5.5 56/4 56/4 7/6.76 7/4.6 96/0 CAB-76C mh /5.5 56/4 94/5.5 5/9.6 7/4.6 /90 CAB-76C mh / 8/0 54/0 68/6.6 8/7. 9/00 CAB-0B6C mh / 8/0 7/.5 97/7.76 8/7. 4/0 CAB-0B6C mh / 8/0 76/4.8 4/9.5 *To order a reactor mounted in NEMA enclosure simply change the second to last digit of the product number from "0" to "". 8/7. 8/ CAB-0B6C Rev. / BuyLog Catalog 4-5

6 Capacitors, Arresters and Harmonic Filters Section 4 Matrix Series D Harmonic Filters Matrix Harmonic filters provide broadband reduction of harmonics. Matrix Harmonic Filters not only offer better performance over other broad band filtering and 8-pulse harmonic reduction techniques, they are also suitable for a wider range of applications. Matrix Harmonic Filters can be installed in either variable or constant torque drive applications and can be applied on either diode or SCR rectifiers. For any application other than variable torque applications, it is suggested that you contact the factory for filter selection. Typical Applications Use Matrix Harmonic filters to minimize harmonic current distortion in these and other 6-pulse rectifier applications: Fans and Pumps Water Treatment Facilities HVAC Systems AC or DC Motor Drives Rectifier type welders Induction Heating Equipment UPS Equipment Elevators Matrix Filter enables most AC drive systems to comply with the voltage and current distortion limits outlined in IEEE 59. A complete harmonic analysis and product selection tool is available on the internet. Go to geelectrical.com and select Products, select Capacitors, choose Matrix Harmonic Filter and then select Energy Savings Calculator and Harmonic Estimator. Matrix Harmonic Filters are multi-stage low pass filters specially configured to avoid the attraction of harmonics from other sources on a shared power system. Matrix filters will not cause power system resonance. However, the configuration of the filter requires that only drives or equivalent loads be loaded on the output of a Matrix harmonic filter. One filter can be used with multiple drives. However, if there is a drive bypass circuit, there must be one filter per drive and the filter and drive combination must be bypassed. Matrix Harmonic Filters are available in a NEMA, NEMA R or as a modular design preassembled onto panels for subsequent assembly into customer supplied cabinet. The Matrix D Filters typically achieve 5% THID at full load and guarantee worst case current distortion at any load between 0% and 00%, will be 8% THID or less at the filter input terminals. The Matrix D Series is typically used in place of applications requiring harmonic mitigation associated with - or 8-pulse rectifiers. The chart below compares the performance of Matrix D Filters to 8-pulse rectifiers in real world applications, which include line voltage unbalance of % to % and loading conditions from 0% to 00%. Matrix D Filter performs better than 8-pulse in normal operating conditions. Matrix D vs. 8-pulse Product Specifications Input Voltage 480 Volts +/ 0% Ambient Temperature: Storage 40 C to 90 C Operating 40 C to 40 C Altitude: 000 meters maximum UL approved File E9686 for U.S. and Canada Minimum System Requirements to Achieve Performance Levels Source Impedance:.5% minimum to 5% maximum System voltage: 480 volts (line to line) +/ 0% Frequency: 60 Hz +/.75 Hz Balanced Line Voltage: within % Background Voltage Distortion: 0% THVD For more product information, go to click on Products and Services and then Products. 4-6 BuyLog Catalog Rev. /

7 Capacitors, Arresters and Harmonic Filters Matrix Series D Harmonic Filters Section 4 Selection Table Matrix D, 480 VAC, 60 HZ, Three Phase, Variable Torque Applications Select Matrix filters based on the horsepower (or kilowatt) rating for the adjustable speed drive or the combined currrent rating of all motors to be connected to the load side of the filter. For constant torque, DC drive or other applications consult factory for proper filter selection. Source Impedance If the source impedance is less than.5% impedance, it is required that an input reactor of at least.5% impedance be added in order to have guaranteed performance level. For best value and performance it is recommended that a % line reactor be used whenever the source impedance is less than.5%. General Purpose Enclosure Style 480 Volts, 60 Hz NEMA & NEMA Wt. NEMA R Wt. Amps HP Drip Proof Enclosure (Lbs.) Weather Resistant Enclosure (Lbs.) Figure 6 MDG0006D CAB-C 76 MDW0006D CAB-C 86 Figure 8 5 MDG0008D CAB-C 79 MDW0008D CAB-C 89 Figure 7.5 MDG00D CAB-C 8 MDW00D CAB-C 9 Figure 4 0 MDG004D CAB-C 89 MDW004D CAB-C 99 Figure 5 MDG00D CAB-C 00 MDW00D CAB-C 0 Figure 7 0 MDG007D CAB-C 5 MDW007D CAB-C 5 Figure 4 5 MDG004D CAB-C 6 MDW004D CAB-C 6 Figure 44 0 MDG0044D CAB-C 8 MDW0044D CAB-C 48 Figure 5 40 MDG005D CAB-7C 90 MDW005D CAB-7C 99 Figure 66 MDG0066D CAB-7C 9 MDW0066D CAB-7C 8 Figure 8 60 MDG008D CAB-7C 4 MDW008D CAB-7C Figure 0 75 MDG00D CAB-7C 44 MDW00D CAB-7C 5 Figure 8 00 MDG08D CAB-6C 85 MDW08D CAB-6C 406 Figure 65 5 MDG065D CAB-6C 44 MDW065D CAB-6C 46 Figure 08 MDG008D CAB-6C 46 MDW008D CAB-6C 48 Figure MDG040D CAB-6C 467 MDW040D CAB-6C 488 Figure 0 MDG00D CAB-6D 66 MDW00D CAB-6D 794 Figure MDG040D CAB-6D 706 MDW040D CAB-6D 88 Figure 4 48 MDG048D CAB-6D 800 MDW048D CAB-6D 9 Figure MDG066D CAB-0D 05 MDW066D CAB-0D 47 Figure MDG0786D CAB-0D 46 MDW0786D CAB-0D 458 Figure Volts, 60 Hz Weight Capacitor Assemblies Amps HP Open Panel (Lbs.) HMR Size (in.) Size (in.) 6 MDP0006D."H X 6"W X 6."D 4.8"H x 4.8"W x 7."D 8 5 MDP0008D 4."H X 6"W X 6."D 4.8"H x 4.8"W x 7."D 7.5 MDP00D 9.4"H x 7."W x 5.7"D 4.8"H x 4.8"W x 8."D 4 0 MDP004D 5.4"H x 7."W x 6."D 4.8"H x 4.8"W x 8."D 5 MDP00D "H x 9"W x 6.5"D 5.6"H x 5.6"W x 7."D 7 0 MDP007D 6 5.8"H x 9"W x 7"D 5.6"H x 5.6"W x 8."D 4 5 MDP004D 7 5.8"H x 9"W x 7.5"D 5.6"H x 5.6"W x 8.7"D 44 0 MDP0044D "H x 9"W x 8"D 5.6"H x 5.6"W x 7."D 5 40 MDP005D 5 6.5"H x."w x 9.6"D 5.6"H x 5.6"W x 7."D 66 MDP0066D "H x."w x 0.7"D 8"H x 7."W x "D 8 60 MDP008D "H x."w x."d 8"H x 7."W x "D 0 75 MDP00D "H x."w x "D 8"H x 7."W x "D 8 00 MDP08D 7 "H x 5."W x."d "H x 7."W x "D 65 5 MDP065D 7 "H x 5."W x.5"d "H x 7."W x "D 08 MDP008D 9 "H x 5."W x "D 5"H x 7."W x "D MDP040D 98 "H x 5."W x.4"d 5"H x 7."W x "D 0 MDP00D "H x 8"W x 0."D 5"H x 7."W x "D 8"H x 7."W x "D MDP040D 8 5.5"H x 8"W x.5"d "H x 7."W x "D 5"H x 7."W x "D 48 MDP048D "H x 8"W x "D 5"H x 7."W x "D 5"H x 7."W x "D "H x 8."W x "D 66 0 MDP066D "H x 4"W x.5"d 5"H x 7."W x "D 5"H x 7."W x "D 5"H x 7."W x "D 786 MDP0786D "H x 4"W x 4"D 5"H x 7."W x "D 5"H x 7."W x "D 5.6"H x 5.6"W x 7."D Rev. / BuyLog Catalog 4-7

8 Capacitors, Arresters and Harmonic Filters Section 4 Matrix Series D Harmonic Filters Outlines and Dimensions CAB-C, 6-44 Amps.00 WITH OPTIONAL NEMA R WEATHERSHIELDS REF SPLASH GUARD FRONT VIEW.4 X.88 SLOT (4) PLACES Figure 6 44 Amps 4.75 RIGHT SIDE VIEW CAB-7C, 5-0 Amps 6.00 WITH OPTIONAL NEMA R WEATHERSHIELDS REF..00 SPLASH GUARD FRONT VIEW.4 X.88 SLOT (4) PLACES Figure 5 0 Amps 7.75 RIGHT SIDE VIEW For more product information, go to click on Products and Services and then Products. 4-8 BuyLog Catalog Rev. /

9 Capacitors, Arresters and Harmonic Filters Matrix Series D Harmonic Filters Outlines and Dimensions Section 4 CAB-6C, 8-40 Amps WITH OPTIONAL NEMA R WEATHERSHIELDS KIT REF SPLASH GUARD FRONT VIEW.4 X.88 SLOT (4) PLACES Figure 8 40 Amps.75 RIGHT SIDE VIEW CAB-6D, 0-48 Amps 4.00 WITH OPTIONAL NEMA R WEATHERSHIELDS REF. SPLASH GUARD FRONT VIEW.4 X.88 SLOT (4) PLACES.75 RIGHT SIDE VIEW Figure Amps Rev. / BuyLog Catalog 4-9

10 Capacitors, Arresters and Harmonic Filters Section 4 Matrix Series D Harmonic Filters Outlines and Dimensions CAB-0D, Amps WITH OPTIONAL NEMA R WEATHERSHIELDS REF. 7. Figure Amps 7.7 REF. For more product information, go to click on Products and Services and then Products. 4-0 BuyLog Catalog Rev. /

11 Capacitors, Arresters and Harmonic Filters Protective Capacitors for AC Rotating Machines Surge Protection for AC Generators, Synchronous Condensers and Large Motors Section 4 Protective capacitors offer surge protection for AC generators, synchronous condensers and large motors. Dielektrol is the GE non-pcb power capacitor dielectric system, developed to provide an environmentally acceptable product with superior performance and reliability. Protective capacitors contain a film dielectric and hermetically sealed bushings, which permit mounting of capacitors in an upright position or on the side. GE Surge Capacitors protect the winding insulation by reducing the steepness of wave fronts applied to or reflected within the machine windings. Features and Benefits Surge protection for AC Generators, synchronous condensers and large motors Time proven GE HAZY film foil dielectric system Dielektrol Non-PCB insulating fluid Provides Turn-to-Turn insulation protection by reducing steepness of wave fronts applied to or reflected within the machine Used in combination with Tranquell station arresters for optimum protection Protective capacitors contain a film dielectric and hermetically sealed bushings, which permit mounting of capacitors in an upright position or on the side. Altitude: 0 to 5,000 feet with proper derating Dielektrol Non-PCB Dielectric Protective Capacitors with Internal Discharge ResistorsIndoor or Outdoor Mounting Voltage Rating rms Volts L-L Maximum Voltage rms Volts L-L Product Number /60 HZ Poles per Unit * 900* L8BBB0 8L005WH 8L005WH 8L009WH 8L0065WH 8L0009WH 8L00WH 8L000WH 8L0070WH 8L0004WH 8L0005WH 8L005WH L0060WH 8L006WH 8L006WH *8L0004WH and 8L0005WH are rated for DC Applications Microfarads per Pole Approx. Net Weight Lb Kg Protective Capacitors For other mounting arrangements contact the factory. and 460 volt designs are identical and use the same product number. All units are provided with CSA labels. Units are not intended for upside down mounting except for product numbers 8L0060WH, 8L006WH, and 8L006WH. Contact factory for up-to-date Capacitor Outline Drawings. Rev. / BuyLog Catalog 4-

12 Capacitors, Arresters and Harmonic Filters Section 4 Protective Capacitors for AC Rotating Machines Surge Protection for AC Generators, Synchronous Condensers and Large Motors Protective Capacitors for AC Rotating Machines Guide for Superseded Models Superseded Model Number Present Model Number Capacitor Voltage Rating # Poles Superseded Model Number Present Model Number Capacitor Voltage Rating # Poles Superseded Model Number Present Model Number Capacitor Voltage Rating # Poles 8F07 8L005WH 460 8L5WH 8L005WH 9L8BCG0 8L005WH 460 8F07G 8L009WH 460 8L9RH 8L009WH L8BCG0 8L0065WH 700 8F6 8L009WH 8L9UH 8L009WH L8BCJ0 8L009WH F6G 8L009WH 8L9WH 8L009WH L8BCL0 8L0009WH 800 8F7 Discontinued 8L65UH 8L0065WH 700 9L8BCM0 8L000WH 0 8F70G 8L000WH 0 8L65WH 8L0065WH 700 9L8CCE0 8L005WH 8F7G Discontinued 8L6RH 8L005WH 9L8CCG0 8L005WH 460 8F8 8L005WH 8L9RH 8L0009WH 800 9L8CCG0 8L0065WH 700 8F9 8L009WH L9UH 8L0009WH 800 9L8CCJ0 8L009WH F9G 8L009WH L9WH 8L0009WH 800 9L8CCJ0 8L005WH F0 8L009WH CLB0 8L005WH 9L8CCL0 8L0009WH 800 8F0G 8L009WH CLB 8L009WH L8CCM0 8L000WH 0 8F5 Discontinued 0 9CLB 8L009WH L8DCE0 8L005WH 8F5G Discontinued 0 9CLB4 Discontinued 0 9L8DCG0 8L005WH 460 8F45 8L0009WH 800 9CLB5 8L0009WH 800 9L8DCG0 8L0065WH 700 8F45G5 8L0009WH 800 9L8ACE0 8L009WH 9L8DCJ0 8L009WH F467 8L000WH 0 9L8ACE0 Discontinued 9L8DCL0 8L0009WH 800 8F58 8L005WH 460 9L8ACE0 8L005WH 9L8DCM0 8L000WH 0 8F585 8L005WH 9L8ACG0 8L009WH 460 9L8DCM0 8L000WH 0 8F586 8L005WH 460 9L8ACG0 8L005WH 460 9L8ECE0 8L005WH 8F59 8L0009WH 800 9L8ACH0 8L009WH L8ECG0 8L005WH 460 8L0RH 8L000WH 0 9L8ACH0 Discontinued L8ECG0 8L0065WH 700 8L0WH 8L000WH 0 9L8ACJ0 8L009WH L8ECJ0 8L009WH L5RH 8L005WH 460 9L8ACK0 Discontinued 0 9L8FCG0 8L005WH 460 8L5RJ 8L0065WH 700 9L8ACL0 8L0009WH 800 9L8FCG0 8L0065WH 700 8L5UJ 8L005WH 460 9L8ACM0 8L000WH 0 9LA6A9 Discontinued 00 8L5WH 8L005WH 460 9L8BCE0 8L005WH 9LA6B 8L000WH 0 For more product information, go to click on Products and Services and then Products. 4- BuyLog Catalog Rev. /

13 Capacitors, Arresters and Harmonic Filters Fixed Motor and Pump Capacitors (Type GEM OFW) Outdoor Weatherproof -5 kvar 40 Volts -0 kvar 480 Volts Three-phase Delta, 60 Hertz Section 4 Description These Type GEM capacitors are designed primarily for the motor requirements of oil field and other pumping installations. Their application, however, may be extended to other motor applications installed indoor or outdoor. Type GEM OFW capacitors feature multiple cells which are assembled in parallel in a NEMA enclosure. Each capacitor cell features the patented GE Pressure Sensitive Interrupter (PSI) that protects against cell rupture. The metallized polypropylene film dielectric system provides an instantaneous self-healing action and greatly reduced energy losses. Discharge resistors are included to reduce voltage to volts or less within one minute of de-energization. A 4 ft., 4-conductor flexible cable is provided for easy installation. Type GEM capacitors offer high reliability and long life. They are suitable for operation over a temperature range of 40 C to +46 C. GEM also features Dielektrol impregnant which is a biodegradable Class IIIB combustible fluid. Type OFW Motor Capacitor -0 kvar Product Cable A kvar 40 Volts Number Size Inch mm Volts 65L5TL 65L55TL 65L55TL 65L55TL 65L554TL 65L555TL 65L556TL 65L557TL 65L558TL 65L559TL 65L560TL 65L56TL L5TA 65L55TA 65L55TA 65L55TA 65L554TA 65L555TA 65L556TA 65L557TA 65L558TA 65L559TA 65L560TA 65L56TA 65L56TA 65L56TA 65L564TA 65L565TA 65L566TA 65L567TA Note: To determine kvar at 08V, multiply kvar at 40V by.75. Dimensions (See Fig. ) B Inch mm Approx. Weight Lbs. Kg Rev. / BuyLog Catalog 4-

14 Capacitors, Arresters and Harmonic Filters Section 4 Fixed Motor and Pump Capacitors (Type GEM OFW) Dimensions Figure For more product information, go to click on Products and Services and then Products. 4-4 BuyLog Catalog Rev. /

15 Capacitors, Arresters and Harmonic Filters Fixed Low Voltage Power Factor Correction Capacitors Enclosed Indoor Dustproof NEMA and Outdoor Weatherproof NEMA Single Phase or -Phase.0-0 kvar, 60 Hertz 40, 480, Volts Section 4 Description Type GEM Capacitors feature multiple cells which are assembled in parallel in an enclosure suitable for both indoor and outdoor applications (NEMA and NEMA ). Each capacitor cell features the patented GE Pressure Sensitive Interrupter (PSI) that protects against cell rupture. The metallized polypropylene film dielectric system provides an instantaneous self-healing action and greatly reduced energy losses. GEM capacitors include discharge resistors to reduce voltage to volts or less within one minute of de-energization. GEM also features Dielektrol impregnant which is a biodegradable Class IIIB combustible fluid. GEM capacitors offer high reliability and long life. They are suitable for operation over a temperature range of 40 C to +46. The GEM assemblies are UL Listed and CSA labeled. Line Fuses/Blown Fuse Lights To be specified by customer. Order by appropriate basic product number plus suffix for a complete product number. NOTE: NEC Article 460-8B requires capacitors to have overcurrent protection in all ungrounded conductorsexcept if connected on the load side of a motor overload protective device. Mounting GEM 65L800 series can be mounted upright on any level surface, such as a floor, top of a motor control center, or directly to any wall with brackets provided. GEM 65L900 series equipments can also be mounted upright on any level surface. An adapter kit is required for wall mounting. Order the wall mounting kit by product number 86C005. Typical Type GEM, cover removed NOTE: Replacement EDT/EWT Equipments including 55L series capacitors are available on request. Please contact the factory. (For New Equipments use the 65L Series.) Line Connection and Cable Entrance Line connection and cable entrance on Figure equipments must be made through the right end panel. For all other equipment figures the entrance may be made through either end panel (after first punching out the appropriate size hole). Replacement Fuses Unit Rating Volts -ph kvar Fuse Amps Fuse Class MIDGET T T MIDGET T T -5 0 MIDGET T T Note: Obsolete fuses 47A7804 and 47A7805 used in 65L, 65L6, and 7F6 assemblies have been replaced by fuse kit 08A Refer to factory for single-phase fuses. Product Number 47A A A A A A A780 47A A7809 Rev. / BuyLog Catalog 4-5

16 Capacitors, Arresters and Harmonic Filters Section 4 Fixed Low Voltage Power Factor Correction Capacitors Enclosed Indoor Dustproof NEMA and Outdoor Weatherproof NEMA Single Phase or -Phase.0-0 kvar, 60 Hertz 40, 480, Volts.0- kvar, 40 Volts kvar Basic Product No. 65L800 65L80 65L80 65L80 65L804 65L805 65L806 65L807 65L808 65L809 65L80 65L8 65L8 65L8 65L84 65L85 65L86 65L87 65L88 65L89 65L80 65L8 No Fuses Suffix TL TL TL TL TL TL TL TL TL TL TL TL TL TL TL TL TL TL TL TL TL TL 40 Volt, -phase Delta Fuses Suffix TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN TN Fuses, Lights Suffix TQ TQ TQ TQ TQ TQ TQ TQ TQ TQ TQ TQ TQ TQ TQ TQ TQ TQ TQ TQ TQ TQ No Fuses Suffix TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX 40 Volt, -phase Fuses Suffix TY TY TY TY TY TY TY TY TY TY TY TY TY TY TY TY TY TY TY TY TY TY Fuses & Lights Suffix TZ TZ TZ TZ TZ TZ TZ TZ TZ TZ TZ TZ TZ TZ TZ TZ TZ TZ TZ TZ TZ TZ Fig. No. (See page 4-) Lbs L8 65L8 65L84 TL TL TL TN TN TN TQ TQ TQ L85 TL TN TQ 8 See Note on page 4-5 referring to NEC Article 460-8B. Approx. Weight gk EXAMPLE: 40V, -phase, 5 kvar, with fuses and blown fuse lights: Product Number: 65L85TQ. Note: To determine kvar at 08V, multiply kvar at 40V by.75. Consult factory for additional Single-phase designs. See page 4- for outline diagrams and dimensions. For more product information, go to click on Products and Services and then Products. 4-6 BuyLog Catalog Rev. /

17 Capacitors, Arresters and Harmonic Filters Fixed Low Voltage Power Factor Correction Capacitors Enclosed Indoor Dustproof NEMA and Outdoor Weatherproof NEMA Single Phase or -Phase.0-0 kvar, 60 Hertz 40, 480, Volts Section kvar, 40 Volts kvar Basic Product No. No Fuses Suffix 40 Volt, -phase Delta Fuses Suffix Fuses, Lights Suffix No Fuses Suffix 40 Volt, -phase Fuses Suffix Fuses & Lights Suffix Fig. No. (See page 4-) Approx. Weight Lb s K g L904 TL TN TQ TX TY TZ L905 TL TN TQ TX TY TZ L906 TL TN TQ TX TY TZ L907 TL TN TQ TX TY TZ L908 TL TN TQ TX TY TZ L909 TL TN TQ TX TY TZ L90 TL TN TQ TX TY TZ L9 TL TN TQ TX TY TZ L9 TL TN TQ TX TY TZ L9 TL TN TQ TX TY TZ L94 TL TN TQ TX TY TZ L95 TL TN TQ TX TY TZ L96 TL TN TQ TX TY TZ L97 TL TN TQ TX TY TZ L98 TL TN TQ TX TY TZ L99 TL TN TQ TX TY TZ L90 TL TN TQ TX TY TZ L9 TL TN TQ TX TY TZ L9 TL TN TQ TX TY TZ L9 TL TN TQ TX TY TZ L94 TL TN TQ TX TY TZ L95 TL TN TQ TX TY TZ L96 TL TN TQ L97 TL TN TQ L98 TL TN TQ L99 TL TN TQ L90 TL TN TQ See Note on page 4-5 referring to NEC Article 460-8B. Consult factory for additional Single-phase designs. Rev. / BuyLog Catalog 4-7

18 Capacitors, Arresters and Harmonic Filters Section 4 Fixed Low Voltage Power Factor Correction Capacitors Enclosed Indoor Dustproof NEMA and Outdoor Weatherproof NEMA Single Phase or - Phase.0-0 kvar, 60 Hertz 40, 480, Volts.0-00 kvar, 480 Volts 480 Volt, -phase Delta 480 Volt, -phase Approx. Fig. No. No Fuses Fuses Fuses, Lights No Fuses Fuses Fuses & Lights Weight Basic (See page kvar Product No. Suffix Suffix Suffix Suffix Suffix Suffix 4-) Lb s K g.0 65L800 TA TC TE TR TS TT L80 TA TC TE TR TS TT L80 TA TC TE TR TS TT L80 TA TC TE TR TS TT L804 TA TC TE TR TS TT L805 TA TC TE TR TS TT L806 TA TC TE TR TS TT L807 TA TC TE TR TS TT L808 TA TC TE TR TS TT L809 TA TC TE TR TS TT L80 TA TC TE TR TS TT L8 TA TC TE TR TS TT L8 TA TC TE TR TS TT L8 TA TC TE TR TS TT L84 TA TC TE TR TS TT L85 TA TC TE TR TS TT L86 TA TC TE TR TS TT L87 TA TC TE TR TS TT L88 TA TC TE TR TS TT L89 TA TC TE TR TS TT L80 TA TC TE TR TS TT L8 TA TC TE TR TS TT L8 TA TC TE TR TS TT L8 TA TC TE TR TS TT L84 TA TC TE TR TS TT L85 TA TC TE TR TS TT L86 TA TC TE TR TS TT L87 TA TC TE TR TS TT L88 TA TC TE TR TS TT L89 TA TC TE TR TS TT L80 TA TC TE TR TS TT L8 TA TC TE TR TS TT L8 TA TC TE TR TS TT L8 TA TC TE TR TS TT L84 TA TC TE TR TS TT L85 TA TC TE TR TS TT 8 7. See Note on page 4-5 referring to NEC Article 460-8B. For more product information, go to click on Products and Services and then Products. 4-8 BuyLog Catalog Rev. /

19 Capacitors, Arresters and Harmonic Filters Fixed Low Voltage Power Factor Correction Capacitors Enclosed Indoor Dustproof NEMA and Outdoor Weatherproof NEMA Single Phase or - Phase.0-0 kvar, 60 Hertz 40, 480, Volts Section kvar, 480 Volts 480 Volt, -phase Delta 480 Volt, -phase Approx. No Fuses Fuses Fuses, Lights No Fuses Fuses Fuses & Lights Fig. No. Weight Basic (See page kvar Product No. Suffix Suffix Suffix Suffix Suffix Suffix 4-) Lb s K g L94 TA TC TE TR TS TT L95 TA TC TE TR TS TT L96 TA TC TE TR TS TT L97 TA TC TE TR TS TT L98 TA TC TE TR TS TT L99 TA TC TE TR TS TT L90 TA TC TE TR TS TT L9 TA TC TE TR TS TT L9 TA TC TE TR TS TT L9 TA TC TE TR TS TT L94 TA TC TE TR TS TT L95 TA TC TE TR TS TT L96 TA TC TE TR TS TT L97 TA TC TE TR TS TT L98 TA TC TE TR TS TT L99 TA TC TE TR TS TT L90 TA TC TE TR TS TT L9 TA TC TE TR TS TT L9 TA TC TE TR TS TT L9 TA TC TE TR TS TT L94 TA TC TE TR TS TT L95 TA TC TE TR TS TT L96 TA TC TE TR TS TT L97 TA TC TE TR TS TT L98 TA TC TE TR TS TT L99 TA TC TE TR TS TT L940 TA TC TE TR TS TT L94 TA TC TE TR TS TT L94 TA TC TE TR TS TT L94 TA TC TE TR TS TT See Note on page 4-5 referring to NEC Article 460-8B. EXAMPLE: 480V, -phase, kvar, with fuses no lights: Product Number: 65L85TC. Rev. / BuyLog Catalog 4-9

20 Capacitors, Arresters and Harmonic Filters Section 4 Fixed Low Voltage Power Factor Correction Capacitors Enclosed Indoor Dustproof NEMA and Outdoor Weatherproof NEMA Single Phase or -Phase.0-0 kvar, 60 Hertz 40, 480, Volts.0-00 kvar, Volts kvar Basic Product No. No Fuses Suffix Volt, -phase Wye Fuses Suffix Fuses, Lights Suffix Fig. No. (See page 4-) Approx. Weight Lbs Kg L800 65L80 65L80 65L80 65L804 65L805 65L806 65L807 65L808 65L809 65L80 65L8 TF TF TF TF TF TF TF TF TF TF TF TF TH TH TH TH TH TH TH TH TH TH TH TH TK TK TK TK TK TK TK TK TK TK TK TK L8 65L8 65L84 65L85 65L86 65L87 TF TF TF TF TF TF TH TH TH TH TH TH TK TK TK TK TK TK L88 65L89 65L80 65L8 65L8 65L8 65L84 65L85 65L86 65L87 TF TF TF TF TF TF TF TF TF TF TH TH TH TH TH TH TH TH TH TH TK TK TK TK TK TK TK TK TK TK L88 65L89 65L80 65L8 65L8 65L8 65L84 65L85 TF TF TF TF TF TF TF TF TH TH TH TH TH TH TH TH TK TK TK TK TK TK TK TK See Note on page 4-5 referring to NEC Article 460-8B. For more product information, go to click on Products and Services and then Products. 4-0 BuyLog Catalog Rev. /

21 Capacitors, Arresters and Harmonic Filters Fixed Low Voltage Power Factor Correction Capacitors Enclosed Indoor Dustproof NEMA and Outdoor Weatherproof NEMA Single Phase or -Phase.0-0 kvar, 60 Hertz 40, 480, Volts Section kvar, Volts kvar Basic Product No. No Fuses Suffix Volt, -phase Wye Fuses Suffix Fuses, Lights Suffix Fig. No. (See page 4-) Approx. Weight Lbs Kg L94 65L95 TF TF TH TH TK TK L96 65L97 65L98 65L99 65L90 65L9 65L9 65L9 TF TF TF TF TF TF TF TF TH TH TH TH TH TH TH TH TK TK TK TK TK TK TK TK L94 65L95 65L96 65L97 65L98 65L99 TF TF TF TF TF TF TH TH TH TH TH TH TK TK TK TK TK TK L90 65L9 65L9 65L9 65L94 65L95 TF TF TF TF TF TF TH TH TH TH TH TH TK TK TK TK TK TK L96 65L97 65L98 65L99 65L940 65L94 65L94 65L94 TF TF TF TF TF TF TF TF TH TH TH TH TH TH TH TH TK TK TK TK TK TK TK TK See Note on page 4-5 referring to NEC Article 460-8B. Rev. / BuyLog Catalog 4-

22 Capacitors, Arresters and Harmonic Filters Section 4 Fixed Low Voltage Power Factor Correction Capacitors Enclosed Indoor Dustproof NEMA and Outdoor Weatherproof NEMA Single Phase or -Phase.0-0 kvar, 60 Hertz 40, 480, Volts Dimensions Fig.. 65L8 Fig.. 65L8 Fig.. 65L8 For more product information, go to click on Products and Services and then Products. 4- BuyLog Catalog Rev. /

23 Capacitors, Arresters and Harmonic Filters Fixed Low Voltage Power Factor Correction Capacitors Enclosed Indoor Dustproof NEMA and Outdoor Weatherproof NEMA Single Phase or - Phase.0-0 kvar, 60 Hertz 40, 480, Volts Section 4 Dimensions Front View Side View Fig L9 Fig L9 Fig. 8. All 65L9 units Fig L9 Fig L9 Rev. / BuyLog Catalog 4-

24 Capacitors, Arresters and Harmonic Filters Section 4 Fixed Low Voltage Power Factor Correction with Harmonic Filter Equipment Metal-Enclosed (GEMTRAP) Application The proliferation of electronic equipment used to improve efficiencies and provide more reliable performance causes harmonics on power systems. Equipment such as variable speed AC and DC drives, uninterruptible power supplies, switching power supplies and other solid state controls or devices inject non-linear components into what was a linear system. The application of power factor correction capacitor systems can create unwanted increases in harmonic voltage and current unless the capacitors are properly applied with reactors, in series with the capacitor, to suppress harmful harmonics. GE s line of fixed, harmonically suppressed capacitors permits the installation of power factor correction capacitors on systems with nonlinear components. The GEMTRAP system can be tuned to any desired frequency but is normally tuned to the 4.7th harmonic. Design The installation of this system is application specific. Contact the GE Sales office or the factory to ensure that the proper combination of capacitors and reactors is used. Misapplication may result without proper guidance. Engineering Specifications Fixed Power Factor Capacitor Equipment Equipment Construction Enclosure and wiring hood: Indoor/outdoor gasketed heavy gauge steel. Finished with a zinc rich primer and an ANSI #70 enamel overcoat. Louvered panels around reactors for protection and cooling. Mounting: Floor mounting. Capacitor Fuses: UL recognized, designed specifically for capacitor applications. Rated VAC, 00kAIC. Fast acting and current limiting; allows clearing action of capacitors while protecting from catastrophic failures. Three phase fusing standard. Aluminum Connecting Bus for Parallel Cells Input Connections: Listed Cu/Al Mechanical wire connectors, sized for kvar requirements, mounted on top of bus for easy access. Harmonic Reactor Options Blown fuse lights Consult factory for larger kvar requirements Consult factory for custom applications and designs Applicable Standards NEMA, IEEE/ANSI, NEC Ratings 40V, 5 to kvar; ph 480 V, 5 to 00 kvar; ph V; 5 to 00 kvar; ph Capacitor Cell Industrial Rated Capacitor cells For more product information, go to click on Products and Services and then Products. 4-4 BuyLog Catalog Rev. /

25 Capacitors, Arresters and Harmonic Filters Fixed Low Voltage Power Factor Correction with Harmonic Filter Equipment Metal-Enclosed (GEMTRAP) Three-phase, 60Hz 40, 480, Volts NEMA Enclosure Normally tuned for the 4.7th Harmonic Can be tuned to any desired frequency. Note: Do not apply Harmonic Filters without a detailed analysis of the power system. Volts kvar Basic Product No. 8FH05DF 8FH05DF 8FH040DF 8FH045DF 8FH0DF 8FH05FF 8FH00FF 8FH040FF 8FH0FF 8FH075FF 8FH080FF 8FH00FF 8FH0FF 8FH5FF 8FH40FF 8FHFF 8FH75FF 8FH00FF 8FH05HF 8FH00HF 8FH040HF 8FH0HF 8FH075HF 8FH080HF 8FH00HF 8FH0HF 8FH5HF 8FH40HF 8FHHF 8FH75HF 8FH00HF Caps with Reactors Incl () Fuses Fig. With Lights Suffix L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L Apprx. Wt. Lbs. (kg) 95 (88) 4 (55) 46 (57) 5 (60) 56 (6) 59 (7) 9 (87) 97 (90) 0 (9) 5 (07) 6 (0) 79 (7) 44 (95) 447 (0) 0 (7) 54 (4) 54 (8) 568 (58) 59 (7) 9 (87) 96 (89) 96 (89) 45 () 48 () 7 () 484 (0) 487 () 495 (5) 0 (7) 56 (9) 55 (5) System Analysis Requirements Primary Volts Transformer: L - L kva Secondary Volts Transformer: kva Transformer impedance % Fundamental Freq. Hz Total System Load KW Section 4 Power Factor: Existing: % Desired % Include One-Line diagram, if available Harmonic Analysis: Voltage/Current Spectrum Outline Dimensions (inches) Rev. / BuyLog Catalog 4-5

26 Capacitors, Arresters and Harmonic Filters Section 4 Automatic Fast-Switching LV Power Factor Correction Capacitors GEMATIC Quick Response Fast Response, Transient-Free Reactive Power Compensation Systems Ultra Fast Response (UFR): A real-time, transient-free system used to compensate extremely rapid loads within one cycle (typically 5-6 msec). Fast Response (FR): A fast, transient-free system, used to compensate any load within -4 seconds. Advantages Ultra Fast Response (UFR) and Fast Response (FR): Transient-free capacitor group switching, using electronic switching elements Prevent damage to sensitive electronic equipment Saves energy Harmonic filtration Accurate power factor control, even in the presence of harmonics Dramatically increases the life expectancy of switching elements and capacitors Considerably lower temperature rise of capacitors and inductors due to unique scan feature Built-in three phase network analyzer, measuring all network parameters including harmonics Unique self-testing and comprehensive reporting feature Power IQ Ultra Fast Response (UFR) (in addition to the above): Cycle-by-cycle reactive power compensation (total acquisition time of 5-6 msec) Prevents voltage drop and flickering Used for Real Time applications, such as spot welding and motor start-up Enhances capacity of local generator systems, such as diesel and windmill generators Combination of one to three single-phase systems available for unbalanced loads Types Available Basic Systems: Include iron core reactors to limit the inrush current with either: Detuned Systems: Include iron core reactors that detune the network to prevent resonance and absorb up to % of the 5th harmonic, or Tuned Systems: Individually designed to absorb the 5th and 7th harmonics For more product information, go to click on Products and Services and then Products. 4-6 BuyLog Catalog Rev. /

27 Capacitors, Arresters and Harmonic Filters Automatic Fast-Switching LV Power Factor Correction Capacitors GEMATIC Quick Response Section 4 Controller Specifications Power Supply 5/0V, /60 Hz LCD Display Size 94 x 76 mm LCD Display Resolution Graphic 60 x 8 pixels LCD Display Type FSTN, LED backlight Frequency 45 to 65 Hz Power Consumption 0 VA Operating Temperature -0 to +55 C 9 Analog Channels current channels for mains load current channels for Equalizer cabinet 4 voltage channels Communications RS485/4 communications port Protocol ELCOM, Modbus/RTU Alarm Voltage free N.O./N.C. relay, max Vac Protection Class IP 40 Dimensions 44 x 44 x 8 mm Weight.4kg Storage Temperature -5 to 70 C Electromagnetic Compatibility EN08-, EN08-, EN5, EN0-4-//4/5, ENV04, EN4 Safety Standards EN-, EN49-, UL8 Controller Features Measurement Level Parameter Phases Loads 4 Frequency Common Mains Phase Current L, L, L Mains, Load, Cap. Neutral Current Neutral Mains Phase to Phase Current L-, L-, L- Mains, Load Phase Voltage L, L, L Mains Neutral Voltage Neutral Mains Phase to Phase Voltage L-, L-, L- Mains Active Power (kw) L, L, L, Total Mains Reactive Power (kvar) L, L, L, Total Mains, Load, Cap. Apparent Power (kva) L, L, L, Total Mains, Load, Cap. Power Factor L, L, L, Total Mains, Load, Cap. Time of use (TOU) in, out, net, total: Active Energy (kwh) Total Mains Reactive Energy (kvarh) Total Mains THD at Phase Current L, L, L Mains, Load, Cap. THD at Neutral Current Neutral Mains THD at Phase to Phase Current L-, L-, L- Mains, Load THD at Phase Voltage L, L, L Mains THD at Neutral Voltage Neutral Mains THD at Phase to Phase Voltage L-, L-, L- Mains Harmonics of Phase Current L, L, L Mains, Load, Cap. Harmonics of Neutral Current Neutral Mains Harmonics of Ph. to Ph. Current L-, L-, L- Mains, Load Harmonics of Phase Voltage L, L, L Mains Harmonics of Neutral Voltage Neutral Mains Harmonics of Ph. to Ph. Voltage L-, L-, L- Mains Waveforms of Phase Current L, L, L Mains, Load, Cap. Waveforms of Neutral Current Neutral Mains Waveforms of Ph. to Ph. Current L-, L-, L- Mains Waveforms of Phase Voltage L, L, L Mains Waveforms of Neutral Voltage Neutral Mains Waveforms of Ph. to Ph. Voltage L-, L-, L- Mains System Log Event Log Data Log (future) Typical Screens Rev. / BuyLog Catalog 4-7

28 Capacitors, Arresters and Harmonic Filters Section 4 Automatic Fast-Switching LV Power Factor Correction Capacitors GEMATIC Quick Response Power IQ Measurement and Analysis Software This software displays the system status as well as the measurement results on numerous screens running under Windows. All network parameters, including harmonics up to the 6rd, can be recorded at preselected intervals. The duration of the recording is only limited to the size of the computer s hard disk. The software can be set to record data based on selected triggers of various network parameters, such as voltage sags and/or current spikes. The system records before and after the trigger event. The software has intranet and internet support. Iron Core Tuned or Detuned Reactor Capacitors Capacitor/Reactor Module Iron Core Limiting Capacitors Switching Module For more product information, go to click on Products and Services and then Products. 4-8 BuyLog Catalog Rev. /

29 Capacitors, Arresters and Harmonic Filters Automatic Fast-Switching LV Power Factor Correction Capacitors GEMATIC Quick Response Section 4 Features Design Steel sheet cabinet Enclosure Finish Epoxy powder coated, in gray (RAL 70) Internal parts rust proof aluzinc Rated Voltage V/ Hz and 480V/60 Hz Other voltage values are available upon request Output rating Refer to table Other output ratings are available upon request Capacitors Low loss, self-healing, IEC 8-/ Ambient Temperature +40 C max short time +5 C average in 4 hours +0 C annual average -0 C low limit Protection class: IP 0. Standards: ElectromagneticEN08-, EN08-, EN5 CompatibilityEN0-4-//4/5, ENV04, ENV 4 Safety StandardsEN-, EN49-, UL8 Standard Balanced Systems for 480V/60 Hz Networks Systems with inrush limiting reactors Detuned systems with tuning frequency of 45 Hz (4.08th Harmonic at 480Vac/60 Hz) up to 00kVAR per group at V/ Hz Tuned systems with tuning frequency of 8 Hz (4.7th Harmonic at 480Vac/60 Hz) Non-Standard Systems (5V-000V /60 Hz or 00V-40V /60 Hz) With circuit breaker or load breaker With or without busbar connection Single cabinet Dual door single cabinet Mechanical structure and dimensions of larger systems are available upon request Option Packages F G W Reactors Lights and Reactors Lights, Breaker and Reactors For pricing, contact One-Stop or Factory. GEMATIC Quick Response Ultra Fast Response (UFR) (5-6 msec) requires special application for selection and sizing. Contact factory for application assistance. GEMATIC Quick Response Fast Response (-4 sec.) Contact Factory for ratings and product numbers. Rev. / BuyLog Catalog 4-9

30 Capacitors, Arresters and Harmonic Filters Section 4 Automatic LV Power Factor Correction Capacitors Type GEMATIC Compact and GEMATIC Select Three-phase, 60 Hertz 40, 480, Volts Description GEMATIC multi-step power factor control equipment automatically maintains desired power factor level, adjusting to system load requirements in selected kvar steps. The solid-state control responds to a current signal from the optional current transformer and to a voltage signal from a potential transformer included in the equipment. GEMATIC equipments feature capacitors with a metallized dielectric system providing a self-healing action and reduced energy losses. The biodegradable impregnant is a class IIIB combustible fluid. Discharge resistors reduce the voltage to volts or less within one minute of de-energization. The capacitor cells are phase and are designed for 0% of rated voltage, 5% of rated current, and, 5% of rated kvar. The power factor controller requires a CT signal for operation. The CT primary should be sized for the total phase current to be compensated (capacitor current and load current). Typically, the total phase current should be % to 80% of the CT primary rating. The CT secondary is rated 5A. The CT is connected to one phase of the equipment and the factory installed PT is connected across the other two phases. GEMATIC equipment includes: Solid-state multi-step power factory controller with digital display and indication of loss of kvar or blown fuse Three phase self-healing metallized capacitors Stage contactors Potential transformer Plated copper bus Three fuses for each stage Modular construction easily uprated UL and C-UL Listed Additional Features GEMATIC Compact NEMA enclosure standard (NEMA R available) 65 kaic bracing Optional breaker ( amp 5kAIC maximum) Optional blown fuse indicating lights GEMATIC Select NEMA enclosure standard (NEMA 4R and NEMA available) 00 kaic bracing Optional breaker Optional blown fuse indicating lights *60 enclosure available for low kvar ratings. Consult factory. GEMATIC Compact GEMATIC Select For more product information, go to click on Products and Services and then Products. 4-0 BuyLog Catalog Rev. /

31 Capacitors, Arresters and Harmonic Filters Automatic LV Power Factor Correction Capacitors Type GEMATIC Compact and GEMATIC Select Three Phase, 60 Hertz 40, 480, Volts Section 4 GEMATIC Compact 40 volts kvar Basic Product No. 40 7FJ040D0 60 7FJ060D0 80 7FJ4080D0 00 7FJ0D0 0 7FJ60D0 Suffix L (Indicating Lights); Suffix B (Circuit Breaker) kvar/step *Breaker Rating GEMATIC Compact 480/ volts kvar Basic Product No. kvar/ Step *480 V Breaker Rating * V Breaker Rating 7FJ0F FJ075F FJ00F FJ5F5 5 7FJF 75 7FJ475F FJF 5 7FJ55F5 5 7FJ5F 75 7FJ675F FJF Suffix L (Indicating Lights); Suffix B (Circuit Breaker) NOTE: For volts, replace second F in the basic product number with H. Example: 7FJ00F5 becomes 7FJ00H5. Contact Factory for NEMA R. GEMATIC Select 40 volts Example of GEMATIC Select Product Number. 00kVAR, 480V, with Lights, Breaker and copper bus, 7FCF5R0. kvar Basic Product No. 7FCD55 7FC55D55 7FC6D55 7FC775D55 7FC800D55 7FC95D55 7FC0D55 7FC00D55 kvar/step Breaker Rating Rev. / BuyLog Catalog 4-

32 Capacitors, Arresters and Harmonic Filters Section 4 Automatic LV Power Factor Correction Capacitors Type GEMATIC Compact and GEMATIC Select Three Phase, 60 Hertz 40, 480, Volts GEMATIC Select 480/ volts kvar Basic Product No. 7FC00F55 7FC5F55 7FCF5 7FC475F55 7FCF5 7FC55F55 7FC5F5 7FC675F55 7FCF5 7FC75F55 7FC7F5 7FC875F55 7FC8F5 7FC945F55 7FC94F5 7FCA475F55 7FCA0F5 7FCB55F55 7FCB5F5 7FCC575F55 7FCCF5 kvar/ Step Suffix L (Indicating Lights); Suffix B (Circuit Breaker) 480V Breaker Rating V Breaker Rating NOTE: For volts, replace second F in the basic product number with H. Example: 7FJ00F5 becomes 7FJ00H5. Contact Factory for NEMA R. For NEMA enclosure, replace C in the basic product number with O, (e.g., 7FC8F5 becomes 7FO8F5). For bottom entry last digit of Product Number changes from 5 to 6 (e.g., 7FC8F5 becomes 7FC8F6). CT, V, split core, 4 x 7 window Ratio Multitap w/ Ratio 800/00/0/000/ 00/0/000 : 5 0 : 5 Product Number XT G XT G Option Packages Suffix L B R Option Indicating Lights Breaker Lights & Breaker Note: Add only one suffix letter to the end of product numbers For breakers add the following code for standard breaker option Current Rating kaic Rating Code for Standard Breaker Option C F L N Q T For more product information, go to click on Products and Services and then Products. 4- BuyLog Catalog Rev. /

33 Capacitors, Arresters and Harmonic Filters Automatic LV Power Factor Correction Capacitors and Harmonic Filter Equipment Section 4 Type GEMATIC Custom The GEMATIC Custom offers power factor correction with the flexibility of including harmonic filter reactors initially or adding them later if they are required. Many of today s power systems require modern solutions to power factor correction. The rapid increase in variable speed drive use and other solid state devices has resulted in severe harmonic loads on power systems. GE has 0 years experience in preventing the occurrence of non-sinusoidal resonance. Successful integration in tuned L-C networks solves the problem of parallel resonance. GEMATIC Custom automatic power factor correction systems with -phase harmonic suppression reactors are application specific. Accordingly, each installation requires specific information to aid GE application engineers in designing each system to meet your requirements. This information should include, but not be limited to, kvar requirements, transformer size and impedance, kvasc of the transformer, and a harmonic profile of your system. Load characteristic at the time of the survey and worst case should also be included. The GEMATIC Custom systems may be configured for the addition of harmonic suppression reactors in the future to meet the imminent needs of your system. This reduces initial investment and provides a ready made retrofit package. This system provides total flexibility in achieving maximum automatic power factor correction. Please contact the local GE sales office or the GE factory for any assistance with your particular power factor correction and harmonic suppression needs. Applicable Standards NEMA, IEEE/ANSI, NEC GEMATIC Custom Optional Features Outdoor NEMA R enclosure Main breaker Iron core reactors Blown fuse indicating lights GEMATIC Custom includes Solid-state multi-step power factor controller with digital display and indication of loss of kvar or blown fuse Three phase self-healing metallized capacitors Stage contactors Three fuses for each stage Potential transformer Plated copper bus, 00 kaic bracing NEMA enclosure UL and cul listed Ratings 40 V; up to 00 kvar 480 V and V; up to 0 kvar For larger kvar ratings, contact factory Rev. / BuyLog Catalog 4-

34 Capacitors, Arresters and Harmonic Filters Section 4 Automatic LV Power Factor Correction Capacitors and Harmonic Filter Equipment Outline Dimensions (inches) GEMATIC Custom Three-phase, 60 Hz NEMA or R Enclosure supplied with or without reactors tuned to the 4.7th Harmonic. Option Lights Breaker Reactors Lights and Breaker Lights and Reactors Lights, Breaker, and Reactors Breaker and Reactors Suffix L B F R G W K Section Dimensions A B NEMA 5 5 NEMA R 4 6 Optional Features: ROutdoor NEMA R Enclosure (Change prefix 8FP to 8FR) Selection Table 40 Volts Total kvar 00 Product Number 8FP00D55 kvar/ Step 5 Suffix L Blown Fuse Lts. Suffix F Harmonic Reactors Suffix B Circuit Breaker Circuit Breaker 40 Volt RatingAmps Prefix R NEMA R Enclosure Width (# of Sections) 8FP6D FP0D FP55D FP5D5 8FPD Selection Table 480/ Volts To order Volt, change second F in product number to H. (e.g. 8FP4FA05 becomes 8FP4HA05) Total kvar Product Number kvar/ Step Suffix L Blown Fuse Lts. Suffix F Harmonic Reactors Circuit Breaker 480 Volts Rating Suffix B Circuit Breaker Circuit Breaker Volts Rating Suffix B Circuit Breaker Prefix R NEMA R Enclosure Width (# of Sections) FP00FA05 8FP4F5 8FP4FA05 8FP54F5 8FP50FA05 8FP65F5 8FP6FA05 8FP76F5 8FP7700FA05 8FP87F5 8FP8800FA05 8FP98F5 8FP9900FA05 8FPA9F5 8FPAA00FA05 8FPBB00FA05 8FPCC00FA05 8FPDD00FA05 8FPEE00FA05 8FPFF00FA Price includes cabinet adder for breaker. Enclosure width increases by one section with breaker. For ratings not listed consult factory. Add breaker code suffix shown on page 4- GEMATIC compact and select. For reverse entry last digit of Product Number changes from "5" to "7." For bottom entry "5" changes to "6" and "7" changes to "8." Bottom entry may change equipment width. Consult factory or e-catalog for dimension and pricing of bottom entry. For more product information, go to click on Products and Services and then Products. 4-4 BuyLog Catalog Rev. /

35 Capacitors, Arresters and Harmonic Filters Active Harmonic Filter Section 4 GE GEMACTIVE Active Harmonic Filter Dynamic current injection for harmonic cancellation and power factor correction Reduces harmonics for IEEE 59 (99) standard compliance Decreases harmonic related overheating of cables, switchgear and transformers Reduces downtime caused by nuisance thermal tripping of protective devices Increases electrical network reliability and reduces operating costs Compensates each phase independently UL and CSA approved Parallel connection allows for easy retrofit and installation of multiple units for large networks Filters to the th harmonic Filters entire network or specific loads depending on installation point Response to load fluctuations begins in 40 microseconds with 8 milliseconds for full response to step load changes IGBT based power electronic technology, 00 and 00A models for 08 to 480V, /60 Hz threephase networks GE GEMACTIVE reduces problematic harmonic levels and provides instantaneous power factor correction. Cost savings result from reduced downtime and maintenance. In addition, over-sizing of distribution equipment to provide for harmonics and poor power factor can be avoided. GE GEMACTIVE dynamically corrects power quality by providing: Active Harmonic Filtration, Resonance Prevention, Power Factor Correction and Dynamic VAR Compensation. Rev. / BuyLog Catalog 4-5

36 Capacitors, Arresters and Harmonic Filters Section 4 Active Harmonic Filter Dynamic VAR Compensation by GEMACTIVE Large inductive inrush currents typically cause voltage sags that result in reduced productivity, poor process quality and possible downtime due to undervoltage tripping of devices. GEMACTIVE is able to inject peak current at two and a half times its rms current rating for one cycle. For many applications this level of compensation eliminates visible flicker and improves voltage regulation resulting in better productivity and quality. GEMACTIVE Sizing A harmonic study is not required to select the size of the GEMACTIVE installation. This is because when GEMACTIVE is installed it becomes a lower impedance path for harmonics than the existing power supply. For sizing, please contact GE. To expedite the product selection process, please have a single line diagram and/or details of the application including sizes of transformers, non-linear and linear loads, and any existing filters and capacitors. Fig. : Non-linear current waveform with poor power factor Active Filter Three-phase 60/Hz Current Enclosure 40/480V Rating Type Product Number NEMA Chassis NEMA Chassis NEMA Chassis A0FG A0FC A00FG A00FC A00FG A00FC Fig. : Corrected Current waveform with improved power factor and reduced harmonic content after Active Harmonic Filter Installation Current Transformers Ratio Multi-tap Product Number CT00SC Fig. : Inrush Current without Active Harmonic Filter Fig. 4: Inrush Current with Active Harmonic Filter For more product information, go to click on Products and Services and then Products. 4-6 BuyLog Catalog Rev. /

37 Capacitors, Arresters and Harmonic Filters Fixed MV Power Factor Correction Capacitors Enclosed Indoor Dustproof and Outdoor Weatherproof kvar, 60 Hz, 460, 4800 Volts.0-00 kvar, 40 Volt Section 4 Application Type HWT equipments are suitable for use on indoor or outdoor primary circuits where small amounts of kvar are required. They may be installed at load centers or directly at the terminals of 00 and 0 volt motors. Permissible ambient temperatures are 40 to +45 C. Discharge resistors in each capacitor reduce the voltage to volts or less within 5 minutes of de-energization. Type HWT equipments contain less than three gallons of flammable liquid in a single container and therefore do not require installation in a vault to meet the NEC. Line Terminals Solderless connectors are provided on each phase: Assembly Connector Size One unit #0 - #4 Two unit #4 - /0 Three unit #6 - kcmil Fuses Protection is provided by,000 ampere interrupting capacity current limiting fuses. A pop-up button on the fuse gives visual indication of a blown fuse. GE recommends the use of three fuses for the most complete protection against terminal-to-terminal and terminal-to-ground failures on grounded systems. Two fuses are sufficient to provide protection against terminal-to-terminal failures on ungrounded systems. Blown Fuse Lights Blown fuse lights provide a positive external indication of an operated fuse. A glowing light makes inspection of capacitors easy, effective, and safe. A 0 VAC source must be supplied externally. When ordered with this option, the HWT assembly is supplied with one light per capacitor. For higher voltage designs, contact factory or consult e-catalog. Rev. / BuyLog Catalog 4-7

38 Capacitors, Arresters and Harmonic Filters Section 4 Fixed MV Power Factor Correction Capacitors Complete Assemblies Including Terminal Box, Fuses and Mounting Frame kvar Volt Assemblies Product Number 460 Volt Assemblies Product Number 4800 Volt Assemblies Product Number Fig. No. Approx. Wt. Lb (kg) in. C (mm) Dimensions E in. (mm) in. F (mm) Individual UnitsWith Terminal Box and Fuses Per Unit 5 7F04 7F054 7F (9) 7.68 (70) 6.96 (77) 7F04 7F054 7F (9) 7.68 (70) 6.96 (77) 75 7F04 7F054 7F (9) 7.68 (70) 6.96 (77) 00 7F044 7F0544 7F () 9.44 (748) 8.7 () 5 7F045 7F0545 7F (5) 0.8 (767) 9.46 (40) 0.75 (9) 7F046 7F0546 7F (7).68 (80).96 (04) 0. () 75 7F048 7F0548 7F (9).5 (847).6 () 0.7 (4) 00 7F047 7F0547 7F (4).5 (847).6 () 0.7 (4) 5 7F049 7F0549 7F (47) 6.06 (96) 8. (466) 0.88 () 7F0440 7F F (47) 6.06 (96) 8. (466) 0.88 () F044 7F0544 7F0544 7F F (5) (5) (99) (99) (466) (466) Two Units InterconnectedWith Terminal Box, Fuses Per Unit and Mounting Frame 00 7F (68).4 (849).70 () 5 7F0546 7F F (70).4 (849).70 () 7F0547 7F F (7).4 (849).70 () 75 7F0549 7F F (75).4 (849).70 () 7F0548 7F F (78).4 (849).70 () 45 7F F F (8) 9.8 (995) 8.45 (469) 4 7F0544 7F F (87) 9.8 (995) 8.45 (469) 475 7F0544 7F F (87) 9.8 (995) 8.45 (469) 0 7F0544 7F F (87) 9.8 (995) 8.45 (469) 55 7F F F (9) 9.8 (995) 8.45 (469) F F F F F F F (97) (97) (97) (995) (995) (995) (469) (469) (469) Three Units InterconnectedWith Terminal Box, Fuses Per Unit and Mounting Frame 575 7F ().4 (849).70 () 7F (5).4 (849).70 () 65 7F0544 7F F (0) 9.8 (995) 8.45 (469) 6 7F F F (5) 9.8 (995) 8.45 (469) 675 7F F F (0) 9.8 (995) 8.45 (469) 700 7F F F (0) 9.8 (995) 8.45 (469) 75 7F F F (0) 9.8 (995) 8.45 (469) 7 7F F F (0) 9.8 (995) 8.45 (469) 775 7F F F (5) 9.8 (995) 8.45 (469) F054 7F0554 7F F F F F F0584 7F F F (40) (45) (45) (45) (45) (995) (995) (995) (995) (995) (469) (469) (469) (469) (469) To order Blown Fuse Light option add 00 to the last digits of the standard product numbers above. Example: 7F05446 becomes 7F For units tested and labeled per CSA Standard, add 07 suffix. For more product information, go to click on Products and Services and then Products. 4-8 BuyLog Catalog Rev. /

39 Capacitors, Arresters and Harmonic Filters Fixed MV Power Factor Correction Capacitors Enclosed Indoor Dustproof and Outdoor Weatherproof kvar, 60 Hz, 460, 4800 Volt Section 4 Dimensions HWT Assemblies Including Terminal Box, Fuses Per Unit and Mounting Frame Fig. Fig. Fig. Replacement Capacitor Units and Fuses kvar Capacitor Product No. volts Fuse Dwg. No. 5A64 Product No. Amps Capacitor Product No L0WS60 5L0WS60 5L04WS60 54L0WS60 54L06WS60 54L08WS60 54L7WS60 58L0WS60 6L05WS 6L054WS 6L055WS L0WS60 5L0WS60 5L05WS60 54L04WS60 54L07WS60 54L09WS60 54LWS60 58L0WS60 6L056WS 6L057WS 6L058WS 6L059WS Top and Bottom fuse adapters needed, one each per fuse: Order Product No. 08A This is a kit that contains one top and one bottom adapter. For units tested and labeled per CSA Standard, add 07 suffix. 460 volts Fuse Dwg. No. 5A64 Product No. Amps Capacitor Product No. 5L0WS6 5L0WS60 5L06WS60 54L05WS60 54L0WS60 54L40WS60 54LWS60 58L44WS60 6L060WS 6L06WS 6L06WS 6L06WS 4800 volts Fuse Dwg. No. 5A64 Product No. Amps Rev. / BuyLog Catalog 4-9

40 Capacitors, Arresters and Harmonic Filters Section 4 High Voltage Capacitor Units, Single and Three-Phase Standard Duty (Film/Foil Designs w/dielektrol ) - kvar, 60 Hertz -4,940 Volts Film/Foil Dielektrol is the GE non-pcb low loss power capacitor dielectric system, developed to provide lower operating costs and greatly enhanced fuse coordination for the prevention of case ruptures. The Dielektrol insulating liquid is a Class IIIB combustible fluid. These capacitors are designed to meet ANSI Std 8 Units for special applications (i.e. system harmonics) or other non-standard capacitors, contact Product Department or visit CSA labeling available upon request Single Phase Standard Ratings and Product Numbers - kvar, Volt Single-Phase Capacitor kvar 00 kvar kvar 00 kvar Voltage BIL Bushing Bushing Bushing Bushing Bushing Bushing Bushing Bushing 95 5LWC6 5L0WC6 54LWC6 54L0WC6 54L5WC6 54LWC6 58LWC6 58L0WC LWC59 5L0WC59 54LWC60 54L0WC60 54L5WC60 54LWC60 58LWC60 58L0WC LWC8 5L0WC8 54LWC60 54L0WC60 54L5WC60 54LWC60 58LWC60 58L0WC L4WC60 5L04WC60 54L4WC6 54L04WC6 54L54WC6 54L4WC6 58L4WC6 58L04WC L5WC60 5L05WC60 54L5WC60 54L05WC60 54L55WC60 54L5WC60 58L5WC60 58L05WC L6WC60 5L06WC60 54L6WC60 54L06WC60 54L56WC60 54L6WC60 58L6WC60 58L06WC L7WC60 5L07WC60 54L7WC60 54L07WC60 54L57WC60 54L7WC60 58L7WC60 58L07WC L8WC60 5L08WC60 54L8WC60 54L08WC60 54L58WC60 54L8WC60 58L8WC60 58L08WC L5WC60 5L5WC60 54L5WC60 54L5WC60 54L55WC60 54L55WC60 58L9WC60 58L09WC L4WC60 5L4WC60 54L4WC60 54L4WC60 54L54WC60 54L54WC60 58L0WC60 58L0WC L9WC60 5L09WC60 54L9WC60 54L09WC60 54L59WC60 54L9WC60 58LWC60 58LWC L0WC60 5L0WC60 54L0WC60 54L0WC60 54LWC60 54LWC60 58LWC60 58LWC LWC60 5LWC60 54LWC60 54LWC60 54L5WC60 54L5WC60 58LWC60 58LWC LWC60 5LWC60 54LWC60 54LWC60 54L5WC60 54L5WC60 58L4WC60 58L4WC L55WC6-54L55WC6-54L555WC60-58L55WC60-5L56WC6-54L56WC6-54L556WC60-58L56WC60-00 kvar kvar 0 kvar kvar Voltage BIL Bushing Bushing Bushing Bushing Bushing Bushing Bushing Bushing 95 NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA LWC60 59L0WC60 98LWC60 98L0WC60 NA NA NA NA L4WC6 59L04WC6 98L4WC6 98L04WC6 NA NA NA NA L5WC60 59L05WC60 98L5WC60 98L05WC60 98L55WC60 98L5WC60 98L585WC60 98L565WC L6WC6 59L06WC6 98L6WC6 98L06WC6 98L56WC6 98L6WC6 98L586WC60 98L566WC L7WC60 59L07WC60 98L7WC60 98L07WC60 98L57WC60 98L7WC60 98L587WC60 98L567WC L8WC60 59L08WC60 98L8WC60 98L08WC60 98L58WC60 98L8WC60 98L588WC60 98L568WC L9WC60 59L09WC60 98L9WC60 98L09WC60 98L59WC60 98L9WC60 98L589WC60 98L569WC L0WC60 59L0WC60 98L0WC60 98L0WC60 98LWC60 98LWC60 98L590WC60 98L570WC LWC60 59LWC60 98LWC60 98LWC60 98L5WC60 98L5WC60 98L59WC60 98L57WC LWC60 59LWC60 98LWC60 98LWC60 98L5WC60 98L5WC60 98L59WC6 98L57WC LWC60 59LWC60 98LWC60 98LWC60 98L5WC60 98L5WC60 98L59WC6 98L57WC L4WC6 59L4WC6 98L4WC6 98L4WC6 98L54WC6 98L54WC6 98L594WC6 98L574WC L55WC60-98L55WC6-98L555WC6-98L595WC6-59L56WC60-98L56WC6-98L556WC6-98L596WC60 - Larger kvar units, extra creep options and other voltages are available. Consult factory for product numbers and pricing. For more product information, go to click on Products and Services and then Products BuyLog Catalog Rev. /

41 Capacitors, Arresters and Harmonic Filters High Voltage Capacitor Units, Single- and Three-Phase Heavy Duty (Film/Foil Designs w/dielektrol ) - kvar, 60 Hertz -4,940 Volts Section 4 GE Heavy Duty all-film capacitors are designed, manufactured, and tested to meet the requirements of all applicable ANSI/IEEE, NEMA, and IEC standards. In addition they are designed to exceed the requirements of these standards in terms of continuous rms and peak overvoltage withstand capabilities. They are good for 5% continuous rms overvoltage capability and 5% peak over - voltage capability. These capacitors are suitable for industrial power systems that have higher voltages or harmonic loads. CSA Labeling available upon request and HZ designs also available upon request. GE Heavy Duty 5% Continuous Overvoltage Capability Product Numbers kvar 00 kvar kvar 00kVAR Voltage BIL Bushing Bushing Bushing Bushing Bushing Bushing Bushing Bushing 95 5LWC0 5L0WC0 54LWC0 54L0WC0 54L5WC0 54LWC0 58LWC0 58L0WC LWC0 5L0WC0 54LWC0 54L0WC0 54L5WC0 54LWC0 58LWC0 58L0WC LWC0 5L0WC0 54LWC0 54L0WC0 54L5WC0 54LWC0 58LWC0 58L0WC L4WC0 5L04WC0 54L4WC0 54L04WC0 54L54WC0 54L4WC0 58L4WC0 58L04WC L5WC0 5L05WC0 54L5WC0 54L05WC0 54L55WC0 54L5WC0 58L5WC0 58L05WC L6WC0 5L06WC0 54L6WC0 54L06WC0 54L56WC0 54L6WC0 58L6WC0 58L06WC L7WC0 5L07WC0 54L7WC0 54L07WC0 54L57WC0 54L7WC0 58L7WC0 58L07WC L8WC0 5L08WC0 54L8WC0 54L08WC0 54L58WC0 54L8WC0 58L8WC0 58L08WC L5WC0 5L5WC0 54L5WC0 54L5WC0 54L55WC0 54L55WC0 58L9WC0 58L09WC L4WC0 5L4WC0 54L4WC0 54L4WC0 54L54WC0 54L54WC0 58L0WC0 58L0WC L9WC0 5L09WC0 54L9WC0 54L09WC0 54L59WC0 54L9WC0 58LWC0 58LWC L0WC0 5L0WC0 54L0WC0 54L0WC0 54LWC0 54LWC0 58LWC0 58LWC LWC0 5LWC0 54LWC0 54LWC0 54L5WC0 54L5WC0 58LWC0 58LWC LWC0 5LWC0 54LWC0 54LWC0 54L5WC0 54L5WC0 58L4WC0 58L4WC L55WC0-54L55WC0-54L555WC0-58L55WC0-5L56WC0-54L56WC0-54L556WC0-58L56WC0-00 kvar kvar 0 kvar Voltage BIL Bushing Bushing Bushing Bushing Bushing Bushing 95 NA NA NA NA NA NA NA NA NA NA NA NA LWC0 59L0WC0 98LWC0 98L0WC0 NA NA L4WC0 59L04WC0 98L4WC0 98L04WC0 NA NA L5WC0 59L05WC0 98L5WC0 98L05WC0 98L55WC0 98L5WC L6WC0 59L06WC0 98L6WC0 98L06WC0 98L56WC0 98L6WC L7WC0 59L07WC0 98L7WC0 98L07WC0 98L57WC0 98L7WC L8WC0 59L08WC0 98L8WC0 98L08WC0 98L58WC0 98L8WC L9WC0 59L09WC0 98L9WC0 98L09WC0 98L59WC0 98L9WC L0WC0 59L0WC0 98L0WC0 98L0WC0 98LWC0 98LWC LWC0 59LWC0 98LWC0 98LWC0 98L5WC0 98L5WC LWC0 59LWC0 98LWC0 98LWC0 98L5WC0 98L5WC LWC0 59LWC0 98LWC0 98LWC0 98L5WC0 98L5WC L4WC0 59L4WC0 98L4WC0 98L4WC0 98L54WC0 98L54WC L55WC0-98L55WC0-98L555WC0-59L56WC0-98L56WC0-98L556WC0 - Rev. / BuyLog Catalog 4-4

42 Capacitors, Arresters and Harmonic Filters Section 4 High Voltage Capacitor Units, Single- and Three-Phase Three Phase Cantilever Mount Units These three-phase capacitor units use the same technology as our single-phase units and when mounted directly to a pole offer a convenient single piece alternative to a multi-unit pole mount rack. Standard Ratings and Product Numbers 00 kvar kvar Voltage BIL (kv) - Bushing Grounded Wye 4 - Bushing Ungrounded Wye - Bushing Grounded Wye 4 - Bushing Ungrounded Wye 460/ 95 59L60WC9 59L6WC9 98L60WC9 98L6WC9 470/ L6WC59 59L6WC59 98L6WC59 98L6WC59 00/ L6WC59 59L6WC59 98L6WC59 98L6WC59 800/ L6WC59 59L6WC59 98L6WC59 98L6WC59 4/ L64WC59 59L64WC59 98L64WC59 98L64WC59 Ungrounded Wye Three-Phase Capacitor Contact factory for up to date Capacitor Outline Drawings. For more product information, go to click on Products and Services and then Products. 4-4 BuyLog Catalog Rev. /

43 Capacitors, Arresters and Harmonic Filters High Voltage Capacitor Units, Single- and Three-Phase Three-Phase Units and Accessories Section 4 Pole Mounted Racks Factory AssembledWelded Fuse Holders Total Unit Capacity kV-BIL Product Number F0AA00 F0BA00 F0CA00 F0DA00 5kV-BIL Product Number F4AA004 F6BA004 F6CA004 F6DA004 Product Number F80700 F A6004 5A60049 kv Current 5 00 Rating Interrupting amp. Sym /800 amp. Sym 7 amp. Sym 800 amp. Sym Flipper Springs Field AssemblyBolted Total Capacity # of Units F00860 Field assembly racks are for fixed applications only and will not support the addition of switches. Bird Caps/Wildlife Protectors Description Capacitor Bird Caps with Sleeve BIL Product Number 9F F F008 Product Number 64A70000 Drawing Number 48A A69500 HV Fuses and Fuse Links Drawing Number 5A0078 5A0079 5A0080 5A006 5A008 5A005 5A005 5A006 5A004 5A004 5A0059 5A005 Application Upright Edgemount EEI-NEMA 8T 0T T 5T 0T 5T 0T 40T K 65K 80K 00K Rev. / BuyLog Catalog 4-4

44 Capacitors, Arresters and Harmonic Filters Section 4 High Voltage Pole-Mounted, Open Stack-Rack and Metal Enclosed Equipment Pole-type Equipment Metal Enclosed - kvar, 60 Hertz.4 through 8kV Open Stack-rack Banks kvar and above 00 kvar and above, 60 Hertz Pole Mounted Equipment Description These equipments are pre-wired, factory assembled, and shipped ready for pole installation with single-phase units. Racks are of welded structural aluminum and are suitable for mounting switches and junction box and cable assembly. Lightning arresters and/or potential transformers can also be mounted. Required Data for Pole-Type Quotation: The following questions must be answered before contacting the factory for a quotation.. Total kvar?. Line-to-line (system) voltage?. Line-to-neutral voltage? 4. Bank connection Delta, Grounded Wye, or Floating Wye? 5. Fixed or switched? (check one) a. Fixed expandable (switches later) b. Fixed nonexpandable (no switches later) c. Switch type (vacuum or oil) 6. Number of capacitor bushings ( or )? BIL (Basic Insulation Level) 7. Options (specify): a. Current transformer b. Potential transformer c. Lightning arresters d. Switching controls (example: voltage, current, kvar, time controls) e. Other. Please specify Open Stack-Rack Equipment Description This application is most popular for large blocks of three-phase Kilovar. Capacitor units and individual fuses are installed in welded aluminum racks, either upright or edgemount. Racks are shipped ready for field installation with base and inter-rack insulators, substructure, interconnecting bus wire and other accessories for a three-phase equipment. Harmonic filter banks are available. Submit complete specifications including harmonic currents and voltages. Required Data for Stack-Rack Quotation: The following questions must be answered before contacting the factory for a quotation.. Total kvar?. Line-to-line (system) voltage?. Bank connection Floating Wye, Grounded Wye, Delta, or Double Wye? 4. Fixed or switched? a. If switched, how many steps? b. If switched, how many kvar per step? 5. Is substructure required (8 ft. standard)? 6. Space limitations (if any). Please specify 7. Options (specify): a. Current transformer b. Potential transformer c. Ground switch (phase, neutral, both) d. Other. Please specify 8. When optional apparatus is requested, state the available short circuit current for proper sizing of the options. Three-phase, 60 Hertz is assumed. Specify if different. If switched: a. Supply specification on switch requested. b. Advise if any parallel banks and ratings. Typical in-line pole-type equipment, single-phase units Upright stack-rack equipment Edgemount stack-rack equipment For more product information, go to click on Products and Services and then Products BuyLog Catalog Rev. /

45 Capacitors, Arresters and Harmonic Filters High Voltage Pole-Mounted, Open Stack-Rack and Metal Enclosed Equipment Metal Enclosed Capacitor Banks.4 thru 8KV Section 4 These power factor correction equipments are metal enclosed for indoor and outdoor installations. These banks can be located on a distribution feeder as a small padmount or at the workstation site. Banks are shipped ready for installation. Banks can be provided with the following options: oil or vacuum switching, automatic control and protection, stainless steel housing, custom colors, key mechnical or electrical interlocks, capacitor removal device, NEMA, R, 4, 4X or enclosures. Required Data for Metal Enclosed Quotation: The following questions must be answered before contacting the factory for a quotation..total kvar?.line-to-line (system) voltage?. Bank connection - Floating Wye, Grounded Wye, Delta, or Double Wye? When in doubt Floating Wye is typically the best choice to avoid fault protection issues 4. Fixed or switched? a. If switched do you want automatic control? b. If switched, how many steps? c. If switched, how many kvar per step? 5.Space or access limitations (if any). Please specify 6.Type of Enclosure (Indoor or Outdoor; is Stainless Steel required) 7. Options (specify): Incoming Air Disconnect Main Incoming fuses (capacitors will be individually fused as standard practice) Ground switch (phase, neutral, both) Power factor Controller (see 4a above) Key Interlocks Blown fuse Detection System Control Power Transformer Arresters - Distribution, Intermediate or Station class Incoming Breaker Power Quality Meter Overload protection (Yes or No) Overvoltage protection (Yes or No) Relay requirememts (class, type, brand, other please specify) Other. Please specify 8. When optional apparatus is requested, state the available short circuit current for proper sizing of the options. 9. Harmonic Filter Bank (Yes or No) If yes, tuning point (5th, 7th, th,...) Metal Enclosed Cabinet Rev. / BuyLog Catalog 4-45

46 Capacitors, Arresters and Harmonic Filters Section 4 OEM High Energy Surge Protectors 9L0K Series 0- Volt Ratings This HESP design is intended for mounting in OEM equipment or in an existing enclosure to offer protection against internally and externally generated surges. UL-449, Second Edition Recognized Component designed and tested according to ANSI/IEEE C6.4 and C6.45. Features Energy Capability Options: This high energy capability option permits survivability in demanding environments and a lower clamping level for better protection. High Surge Current Capability: The 76mm HESP protective elements are designed and tested at 00kA per mode. Parallel or Series Connection: Unfused protectors are suitable for series connection in circuits rated up to 00 amps continuous, and T-connection (parallel) with no limitation on continuous load current. The ability to connect the units in the series configuration offers optimum protection. This connection keeps lead length inductive voltage to a minimum and provides the lowest protective levels for each rating. Dependable Protection: The unique zinc oxide "valve" element inside each arrester gives you improved overvoltage protection. These tough elements are designed so that they can handle surge after surge without trouble, breakdown, or repairs. Your Tranquell arrester s protective ability will remain unchanged throughout its service life. Common Mode Protection Option: In addition to normal mode protection (L-L and L-N), HESP offers common mode protection (L-G and N-G) for -phase wye and single-phase or pole devices. This optional protection is recommended for devices remotely located from the system neutral to ground bond. 9L0K Series is direct replacement for superseded 9L0M Series. Selection and Ratings Nominal Voltage Max. Continuous second Diagram Energy Rating UL-449, Second Edition Suppressed Voltage and Configuration Operating Voltage Temporary Overvoltage Figure (Joules Rating (SVR) with 6 leads Product (Volts, rms) (Volts, rms) (Volts, rms) page 4-47 per Phase) L-N N-G L-G, L-L Number 0, Phase L0KAA Line-Neutral 8 L-N 8 Wire L0KAANO 08 WYE/0 Line-Neutral 8 L-N L0KAB4, 4 4 Phase, 4 Wire Line-Line 9 L-L L0KAB4NO 0/40 Line-Neutral 8 L-N L0KAC Phase, Wire Line-Line 76 L-L L0KACNO 40/480 Line-Neutral 76 L-N L0KAD Phase, Wire Line-Line 55 L-L L0KADNO 40, Phase L0KAE Line-Neutral 76 L-N 67 Wire L0KAENO 40 Delta L0KAF Line-Line 76 L-L 67 5, 6 4 Phase, Wire L0KAFNO 40 WYE/8 Line-Neutral 58 L-N L0KAG4, 4 4 Phase, 4 Wire Line-Line 76 L-L L0KAG4NO 480, Phase L0KAJ Line-Neutral 55 L-N 74 Wire L0KAJNO 480 Delta L0KAK Line-Line 55 L-L 74 5, 6 4 Phase, Wire L0KAKNO 480 WYE/77 Line-Neutral 8 L-N L0KAL4, 4 4 Phase, 4 Wire Line-Line 55 L-L L0KAL4NO For optional Common Mode Protection change the product numbers as follows: for single-phase devices substitute in the 8th position of the product number. For -phase WYE devices substitute 4 in the 8th position of the product number. N-G and L-G values for WYE product numbers are only applicable to those units with the optional common mode protection. For service entry applications where the neutral and ground are bonded, the L-G rating is equivalent to the L-N rating. 4 Units indicated are not UL approved. For more product information, go to click on Products and Services and then Products BuyLog Catalog Rev. /

47 Capacitors, Arresters and Harmonic Filters OEM High Energy Surge Protectors 9L0K Series 0 Volt Ratings Section 4 Connection Diagrams 4-terminal device shown Dimensions (in/mm) Series Connection Max. Continuous Current: 00A/Phase T Connection Max. Continuous Current: Unlimited Fig. Single Phase or Wire Fig. Single Phase or 4 Wire "H" Dimension Product Number inches mm 9L0KAA L0KAANO L0KAB L0KAB4NO L0KAC L0KACNO L0KAD L0KADNO L0KAE L0KAENO L0KAF L0KAFNO L0KAG L0KAG4NO L0KAJ L0KAJNO L0KAK L0KAKNO L0KAL L0KAL4NO L0KAM L0KAMNO L0KAN L0KAN4NO 4.8. Fig. Three Phase Wye Ungrounded Fig. 4 Three Phase Wye/4 or 5 Wire/GND Neutral Fig. 5 Three Phase Delta/Ungrounded Fig. 6 Three Delta/One Phase Grounded Rev. / BuyLog Catalog 4-47

48 Capacitors, Arresters and Harmonic Filters Section 4 Tranquell Motor Surge Protector Motor and Generator Surge Protection Equipment Three-Phase, 60 Hz through 4,000 Volt Ratings NEMA /R Enclosure Description Tranquell Motor Surge Protector provides surge protection for AC rotating machines including motors and generators. They are typically applied directly at the motor terminals and consist of GE Tranquell Station Class arresters connected in parallel with GE Dielektrol Protective Capacitor(s). The arresters protect the major insulation to ground by limiting the amplitude of applied impulse waves or reflections within the machine windings, while the protective capacitor(s) reduce the steepness of wave fronts. Studies indicate that this dual protection approach results in significant reduction of lightning stresses imposed on rotating machines and contribute to increased security against failures and downtime costs. Enclosure is suitable for indoor and outdoor applications. How to Select. Determine the nominal system voltage and connection at the equipment being protected (Line-to-Line voltage, delta or wye, grounded or ungrounded).. Select product number (column or ) based on the line to line voltage (column ). Selection Table Voltage Rating rms Volts (L-L) Product No. Delta & Ungrounded Neutral Systems 8F40 Product No. Grounded Neutral Systems Arrester Rating kv rms Arrester MCOV kv rms.55 Capacitor Microfarads per Pole µf 0.5 Dimension "D" (side view) " Weight lbs F " 00 8F " F " F " F " F " 00 8F " F " 00 8F " F " Contact factory for other ratings. 8F " Dimensions: (inches) Front Side For more product information, go to click on Products and Services and then Products BuyLog Catalog Rev. /

49 Capacitors, Arresters and Harmonic Filters Tranquell Secondary Surge Arresters and Protective Capacitors 0-6 Vac Series 9L5F Section 4 Assures Service Continuity The GE Tranquell secondary arrester is specifically designed to protect utility, agricultural, and industrial installations and equipment in the 0-6 volt range from overvoltages caused by lightning discharges. It is available for both single- and threephase application. Applications that provide ideal installations for this arrester are: Exposed secondary circuits Watt hour meters Station auxiliary equipment and circuits Motors and control circuits Distribution transformer secondaries Dependable Protection The unique metal oxide element inside each Tranquell arrester gives you improved overvoltage protection. These tough elements are designed so that they can handle surge after surge without trouble, breakdown, or repairs. Your arrester s protective ability will remain unchanged throughout its service life. Secondary Arresters Indoor or Outdoor Mounting Circuit Max. Permissible Voltage Line-to-Ground No. of Net Weight Product Rating rms Voltage rms Poles (lbs/kg) Number /0.4 9L5HCB /0.4 9L5GCA /0.4 9L5GCB /0.4 9L5GCC00 Fusing To minimize the possibility of violent rupture in the unlikely event of electrical failure of the arrester, current limiting fuses are recommended for all applications above 0 volts. A fuse must be installed in series with each pole of the arrester (i.e. each black wire). See Fuse Selection table below. The GEH-498C instruction book shipped with each arrester also includes fusing guidelines. Fuse Selection For 9L5E Series (above 0V) Arrester Maximum Fuse Location Lightning Impulse, Rating 4 A Long Branch Circuit more than 0m from 00A Service Entrance with wires #4-0 B Major Feeders and Short Branch Circuits ka less than 0m from 8x0 µs Service Entrance C Outside and 0 ka Service Entrance 4x0 µs 0 A; V U.L. Class T 00,000 A Interrupt 0 A; V U.L. Class T 00,000 A Interrupt 0 A; V U.L. Class T 00,000 A Interrupt Non-PCB Secondary Protective Capacitors Indoor or Outdoor Mounting Circuit Max. Permissible Voltage Line-to-Ground No. of Net Weight Product Rating rms Voltage rms Poles (lbs/kg) Number /.8 9L8BBB0 Quantity break pricing applies; consult factory or your GE sales representative. Secondary Surge Arrester Protective Characteristics Discharge Voltage kv Crest Discharge Energy (8 x 0 Microsecond Current Wave) Capabilities Handling.5 ka 5.0 ka 0.0 ka 0.0 ka 8 x 0 microsecond Capability ,000 amp 900 joules per pole Figure Tranquell Arrester Figure Protective Capacitor 5 Maximum impulse expected as described in ANSI/IEEE C6.4 for systems with medium exposure to surges. Arresters have been design tested to impulses as high as 0 ka, 8x0µs. Design tests for secondary arresters as required by ANSI/IEEE standards are limited to a maximum of 0 ka, 4x0µs impulses. 4 UL Class CC (Midget) 0 A fuses are also satisfactory for locations A and B. 5 Secondary capacitor is a -pole device that can be applied with - and -pole arresters by connecting the corresponding black leads and tying off the unused leads. Rev. / BuyLog Catalog 4-49

50 Capacitors, Arresters and Harmonic Filters Section 4 Tranquell Station Arresters Polymer and Porcelain High-Voltage Indoor and Outdoor Service Product Description Tranquell XE porcelain and XEP polymer station arresters provide both excellent protective characteristics and temporary overvoltage capability. Gapless construction results in a design which is simple, reliable and economical while offering excellent fault current capability to meet the most demanding service conditions. The GE arrester is based on the field-proven metal oxide disks known for maintaining stable characteristics. Station arresters are designed and manufactured in accordance with the latest revision of ANSI/IEEE C6.. Tranquell Polymer Station Arrester Porcelain and Polymer Arresters (Station Class) for both Indoor and Outdoor Mounting (.7-6 kvrms) Normally Used on System Voltage Class (L-L) High Impedance Grounded, Porcelain Product Number Silicone 4 Arrester MCOV Capability Ungrounded (Delta) Solidly Metal Top for Rating (L-N) kvrms or Temporarily Grounded Metal Top; Porcelain Top for Indoor or Eyebolt kvrms Porcelain Polymer Ungrounded Circuits Neutral kvrms Indoor / Outdoor Indoor or Cubicle Outdoor 4-hole NEMA Terminal LZGA00S 9LZGB00S 9LXPA00AS 9LXPB00AS LZGA006S 9LZGB006S 9LXPA006AS 9LXPB006AS LZGA009S 9LZGB009S 9LXPA009AS 9LXPB009AS LZGA00S 9LZGB00S 9LXPA00AS 9LXPB00AS LZGA0S 9LZGB0S 9LXPA0AS 9LXPB0AS LZGA05S 9LZGB05S 9LXPA05AS 9LXPB05AS LZGA08S 9LZGB08S 9LXPA08AS 9LXPB08AS LZGA0S 9LZGB0S 9LXPA0AS 9LXPB0AS LZGA04S 9LZGB04S 9LXPA04AS 9LXPB04AS LZGA07S 9LXPA07AS 9LXPB07AS LZGA00S 9LXPA00AS 9LXPB00AS LZGA06S 9LXPA06AS 9LXPB06AS LZGA09S 9LXPA09AS 9LXPB09AS LZGA045S 9LXPA045AS 9LXPB045AS LZGA048S 9LXPA048AS 9LXPB048AS LZTA054AS 9LHMA054S 9LXPA054AS 9LXPB054AS LZTA060AS 9LHMA060S 9LXPA060AS 9LXPB060AS LZTA066AS 9LXPA07AS 9LXPB07AS LZTA07AS 9LHMA07S 9LXPA090AS 9LXPB090AS LZTA090AS 9LHMA090S 9LXPA096AS 9LXPB096AS LZTA096AS 9LHMA096S 9LXPA08AS 9LXPB08AS LZXA08AS 9LHMA08S 9LSPA08AS 9LSPB08AS LZTA08AS 9LHMA08S 9LXPA0AS 9LXPB0AS LZTA0AS 9LHMA0S 9LXPAAS 9LXPBAS LZTAAS 9LHMAS 9LXPA44AS 9LXPB44AS LZTA44AS 9LHMA44S 9LXPA68AS 9LXPB68AS LZTA68AS 9LHMA68S 9LXPA7AS 9LXPB7AS LZTA7AS 9LHMA7S 9LXPA80AS 9LXPB80AS LZTA80AS 9LHMA80S 9LXPA9AS 9LXPB9AS LZTA9AS 9LHMA9S 9LXPA8AS 9LXPB8AS LZTA8AS 9LHMA8S LZTA40AS 9LHMA40S For Nominal 45kV Systems 9LZTA58AS 9LHMA58S 64 For Nominal 45kV Systems 9LZTA64AS 9LHMA64S 76 0 For Nominal 45kV Systems 9LZTA76AS 9LHMA76S 88 4 For Nominal 45kV Systems 9LZTA88AS 9LHMA88S 94 7 For Nominal 45kV Systems 9LZTA94AS 00 4 For Nominal 45kV Systems 9LZTA00AS 45 For Nominal kv Systems 9LZTAAS 9LHMAS 6 64 For Nominal kv Systems 9LZTA6AS For Nominal kv Systems 9LZTA60AS 96 8 For Nominal 0kV Systems 9LZTA96AS 9LHMA96S 40 5 For Nominal 0kV Systems 9LZTA40AS 9LHMA40S 96 8 For Nominal 0kV Systems 9LZTA96AS 40 5 For Nominal 0kV Systems 9LZTA40AS For Nominal 0kV Systems 9LZTA444AS 9LHMA444S For Nominal 765kV Systems 9L6GNS588S For Nominal 765kV Systems 9L6GNS6S Tranquell Arresters are designed to be operated at voltages equal to or less than their continuous capability as stated in column. Based on our recommended MCOV ratings for normal system voltages, for systems with ground faults lasting no more than 0 minutes. For underhung (or upside down) mounting, with eyebolt terminal on the bottom, change letter B of the product number to E. 4 Special Ratings available on request. For more product information, go to click on Products and Services and then Products. 4- BuyLog Catalog Rev. /

51 Capacitors, Arresters and Harmonic Filters Tranquell Station Arresters Porcelain High-Voltage Indoor and Outdoor Service Section 4 Porcelain, Metal Top Station Arrester Dimensions, Leakage Distances, Mounting Clearances and Weights Standard Height "X" Creepage Distance Insulation Withstand Distance Weight Arrester Catalog Duty Cycle MCOV Phase to Phase- Phase to Ground- Number (kv) rms (kv) rms in. mm in. mm in. mm in. mm lbs. kg 9LZGA00S LZGA006S LZGA009S LZGA00S LZGA0S LZGA05S LZGA08S LZGA0S LZGA04S LZGA07S LZGA00S LZGA06S LZGA09S LZGA045S LZGA048S LZTA054AS LZTA060AS LZTA066AS LZTA07AS LZTA090AS LZTA096AS LSXA08AS LZTA08AS LZTA0AS LZTAAS LZTA44AS LZTA68AS LZTA7AS LZTA80AS LZTA9AS LZTA8AS LZTA40AS LZTA58AS LZTA64AS LZTA76AS LZTA88AS LZTA94AS LZTA00AS LZTAAS LZTA6AS LZTA60AS LZTA96AS LZTA40AS LZTA444AS L6GNS588S L6GNS6S Porcelain Top Station Arrester Mounting Clearance Product "X" Overall Height Leakage Dist Phase to Phase Phase To Ground Weight Number MCOV (kv) in mm in mm in mm in mm lb kg 9LZGB00S LZGB006S LZGB009S LZGB00S LZGB0S LZGB05S LZGB08S LZGB0S LZGB04S LZGB07S LZGB00S LZGB00S LZGB06S LZGB09S LZGB045S LZGB048S These are recommended minimum clearances only and as such are not intended to take precedence over existing construction codes or specifications. Rev. / BuyLog Catalog 4-5

52 Capacitors, Arresters and Harmonic Filters Section 4 Tranquell Station Arresters Porcelain High-Voltage Indoor and Outdoor Service Porcelain, Metal Top Station Arrester Insulation Characteristics Minimum Power Frequency Withstand (kvrms) Duty Cycle MCOV Leakage Dist Strike Minimum. x µs Wet Dry Product Number (kv) (kv) in mm in mm Withstand (kv crest) (0 sec) ( min) 9LZGA00S LZGA006S LZGA009S LZGA00S LZGA0S LZGA05S LZGA08S LZGA0S LZGA04S LZGA07S LZGA00S LZGA06S LZGA09S LZGA045S LZGA048S LZTA054AS NA 9LZTA060AS NA 9LZTA066AS NA 9LZTA07AS NA 9LZTA090AS NA 9LZTA096AS NA 9LSXA08AS NA 9LZTA08AS NA 9LZTA0AS NA 9LZTAAS NA 9LZTA44AS NA 9LZTA68AS NA 9LZTA7AS NA 9LZTA80AS NA 9LZTA9AS NA 9LZTA8AS NA 9LZTA40AS NA 9LZTA58AS NA 9LZTA64SS NA 9LZTA76AS NA 9LZTA88AS NA 9LZTA94AS NA 9LZTA00AS NA 9LZTAAS NA Minimum Dry Power Withstand not required by ANSI. Porcelain Top Station Arrester Insulation Characteristics Minimum Power Frequency Withstand (kvrms) Duty Cycle MCOV Leakage Dist Strike Minimum. x µs Wet Dry Product Number (kv) (kv) in mm in mm Withstand (kv crest) (0 sec) ( min) 9LZGB00S LZGB006S LZGB009S LZGB00S LZGB0S LZGB05S LZGB08S LZGB0S LZGB04S LZGB07S For more product information, go to click on Products and Services and then Products. 4-5 BuyLog Catalog Rev. /

53 Capacitors, Arresters and Harmonic Filters Tranquell Station Arresters Porcelain High-Voltage Indoor and Outdoor Service Section 4 Porcelain Station Arrester Protective Characteristics Arrester Ratings Continuous Maximum Arrester Operating Maximum 0.5us Switching Surge Maximum Discharge Voltage using 8/0 Current Wave-kV Product Rated Voltage Voltage (MCOV) Discharge Protective Level Type Number (kv) kv rms Voltage kv kv.5ka ka 5kA 0kA 0kA 40kA 9LZGA00S LZGA006S LZGA009S LZGA00S LZGA0S LZGA05S LZGA08S LZGA0S LZGA04S LZGA07S LZGA00S LZGA06S LZGA09S LZGA045S LZGA048S LZTA054AS LZTA060AS LZTA07AS LZTA090AS Contact Factory LZTA096AS LZXA08AS Hole NEMA 9LZTA08AS LZTA0AS LZTAAS LZTA44AS LZTA68AS LZTA7AS LZTA80AS LZTA9AS LZTA8AS LZTA58AS LZTA64AS LZTA76AS LZTA88AS LZTA94AS LZTA00AS LZTAAS LZTA6AS LZTA60AS LZTA96AS LZTA40AS LZTA444AS L6GNS588S L6GNS6S Maximum discharge voltage for an impulse current wave which produces a voltage wave cresting in 0.5 µs. Discharge currents are 0 ka for.55-45kv MCOV. This can be used for coordination where front-of-wave sparkover was formerly used. Discharge voltages are based on a 0A surge of 45 µs time to crest through 88kV MOV and,000a surge of 45 µs-time to crest through 80kV MCOV and,000a through 45kV MCOV. Rev. / BuyLog Catalog 4-5

54 Capacitors, Arresters and Harmonic Filters Section 4 Tranquell Station Arresters Porcelain High-Voltage Indoor and Outdoor Service 9LZGBO##S Series Rated Voltage -7kV 9LZGAO##S Series Rated Voltage -48kV 9LZ TA###AS Series Rated Voltage 54-44kV 9LZ TA###AS Series Rated Voltage 68kV 9LZ TA###AS Series Rated Voltage 7-40kV 9LZ TA###AS Series Rated Voltage 58-kV 9LZ TA###AS Series Rated Voltage 6 60kV 9LZ TA###AS Series Rated Voltage 96 40kV 4 Hole NEMA Terminal For more product information, go to click on Products and Services and then Products BuyLog Catalog Rev. /

55 Capacitors, Arresters and Harmonic Filters Tranquell Station Arresters Polymer High-Voltage Indoor and Outdoor Service Section 4 Polymer Station Arrester Weights and Dimensions Standard Standard Insulation Withstand Distance Cantilever Strength Arrester Product Arrester Product Number 4 Hole Number Single Duty Cycle MCOV Height "X" Creepage Distance Phase to Phase Phase to Ground Weight Note Note NEMA Eyebolt (kv) rms (kv) rms in mm in mm in mm in mm lbs kg ft-lbs Nm ft-lbs Nm 9LXPA00AS 9LXPB00AS LXPA006AS 9LXPB006AS LXPA009AS 9LXPB009AS LXPA00AS 9LXPB00AS LXPA0AS 9LXPB0AS LXPA05AS 9LXPB05AS LXPA08AS 9LXPB08AS LXPA0AS 9LXPB0AS LXPA04AS 9LXPB04AS LXPA07AS 9LXPB07AS LXPA00AS 9LXPB00AS LXPA06AS 9LXPB06AS LXPA09AS 9LXPB09AS LXPA045AS 9LXPB045AS LXPA048AS 9LXPB048AS LXPA054AS 9LXPB054AS LXPA060AS 9LXPB060AS LXPA07AS 9LXPB07AS LXPA090AS 9LXPB090AS LXPA096AS 9LXPB096AS LXPA08AS 9LXPB08AS LSPA08AS 9LSPA08AS LXPA0AS 9LXPB0AS LXPAAS 9LXPBAS LXPA44AS 9LXPB44AS LXPA68AS 9LXPB68AS LXPA7AS 9LXPB7AS LXPA80AS 9LXPB80AS LXPA9AS 9LXPB9AS LXPA8AS 9LXPB8AS *Center line to center line is equivalent to phase-to-phase center line to ground is equivalent to phase-to-ground. These are recommended minimum clearances only and as such are not intended to take precedence over existing construction codes or specifications. Cantilever Strength - Maximum Working Strength Cantilever strength - Rated Ultimate Cantilever Strength Add.0 to X dimension for 4 Hole NEMA terminal and.88 to X dimension for Eyebolt designs for overall height Polymer Station Arrester Protective Characteristics 9LXPAxxxAS and 9LXPBxxxAS Arrester Ratings Maximum Continuous Maximum Operating Maximum 0.5us Switching Surge Rated Voltage Voltage Discharge Protective Level Maximum Discharge Voltage Using 8/0 Current Wave-kV kv rms (MCOV) kv rms Voltage kv kv.5ka ka 5kA 0kA 0kA 40kA Rev. / BuyLog Catalog 4-55

56 Capacitors, Arresters and Harmonic Filters Section 4 Tranquell Station Arresters Silicone Station Arresters Protective Characteristics Maximum Switching Maximum 0.5µs Surge Protective Level Rated Discharge At Classifying Product Voltage MCOV Voltage Current Levels kv Maximum Discharge Voltage Using an 8/0 Current Wave-kV Number kvrms kvrms kv kv.5ka ka 5kA 0kA 0kA 40kA 9LHMA054S LHMA060S LHMA07S LHMA090S LHMA090S LHMA096S LHMA08S LHMA08S LHMA0S LHMAS LHMA44S LHMA68S LHMA7S LHMA80S LHMA9S LHMA8S LHMA58S LHMA64S LHMA76S LHMAS LHMA96S LHMA40S LHMA444S Silicone Station Arresters Dimensions and Mounting Minimum Mounting Maximum Continuous Minimum Spacing on Center Product Duty Cycle Operating Voltage Height Leakage Phase to Phase Phase to Net Weight Number kv rms kv rms (in.) Distance In-line (in.) Ground (in.) (Lbs.) 9LHMA054S LHMA060S LHMA07S LHMA090S LHMA090S LHMA096S LHMA08S LHMA08S LHMA0S LHMAS LHMA44S LHMA68S LHMA7S LHMA80S LHMA9S LHMA8S LHMA58S LHMA64S LHMA76S LHMAS LHMA96S LHMA40S LHMA444S Maximum discharge voltage for an impulse current wave which produces a voltage wave cresting in 0.5 µs. Discharge Currents are 0kA for 4-5 kv MCOV. This can be used for coordination where front-of-wave sparkover formerly was used. Discharge voltages are based on a 0A surge of 45 µs time to crest through 88kV MCOV and a 000A surge of 45 µs to crest through 80 kv MCOV and 000A through 45 kv MCOV. Minimum clearances are based on arrester protective levels and should be increased when necessary to meet local requirements for spacing of energized equipment. For more product information, go to click on Products and Services and then Products BuyLog Catalog Rev. /

57 Capacitors, Arresters and Harmonic Filters Tranquell Station Arresters Polymer High-Voltage Indoor and Outdoor Service Section 4 Polymer Arresters (Station Class) for both Indoor and Outdoor Mounting (.7-7 kvrms) 9LXPMxxxS, 9LXPNxxxS, and 9LXPTxxxS Pressure Relief Capability: 40 ka rms Energy Handling Capability: 6.0kJ/kV mcov Cantilever Strength: 4,000 inch-pounds, rated ultimate cantilever moment Product Number (Gray Polymer) Arrester Maximum Continuous 4-hole NEMA Pad for Eyebolt Terminal for Rating Voltage Capability Indoor or Outdoor Indoor or Outdoor Indoor or cubicle kvrms (L-N) kvrms Upright Mounting Upright Mounting Terminal Mounting. 9LXPN00S 9LXPT00S 9LXPM00S.55 9LXPN00S 9LXPT00S 9LXPM00S 4.7 9LXPN004S 9LXPT004S 9LXPM004S LXPN005S 9LXPT005S 9LXPM005S LXPN006S 9LXPT006S 9LXPM006S LXPN007S 9LXPT007S 9LXPM007S LXPN008S 9LXPT008S 9LXPM008S LXPN009S 9LXPT009S 9LXPM009S LXPN00S 9LXPT00S 9LXPM00S 0. 9LXPN0S 9LXPT0S 9LXPM0S 5.7 9LXPN05S 9LXPT05S 9LXPM05S LXPN08S 9LXPT08S 9LXPM08S 7 9LXPN0S 9LXPT0S 9LXPM0S LXPN04S 9LXPT04S 9LXPM04S 7 9LXPN07S 9LXPT07S 9LXPM07S LXPN00S 9LXPT00S 9LXPM00S 6 9 9LXPN06S 9LXPT06S 9LXPM06S 9.5 9LXPN09S 9LXPT09S LXPN045S 9LXPT045S LXPN048S 9LXPT048S LXPN054S 9LXPT054S LXPN060S 9LXPT060S LXPN07S 9LXPT07S For weight, dimensional and other technical information, please visit the Arresters section of Polymer Arresters (Station Class)Protective Characteristics 9LXPMxxxS, 9LXPNxxxS and 9LXPTxxxS for both Indoor and Outdoor Mounting (.7-7 kvrms) 9LXPMxxxS, 9LXPNxxxS, and 9LXPTxxxS Pressure Relief Capability: 40 ka rms Energy Handling Capability: 6.0kJ/kV mcov Cantilever Strength: 4,000 inch-pounds, rated ultimate cantilever moment Product Number 9LXPNxxxS Rating voltage 0.5 µsec 0 ka Switching Surge Maximum Discharge Voltage - kv crest 9LXPMxxxS* kv rms mcov kv rms Max IR-kV crest Max IR-kV crest.5 ka ka 5 ka 0 ka 0 ka 40 ka 9LXPT00S LXPT006S LXPT009S LXPT00S LXPT0S LXPT05S LXPT08S LXPT0S LXPT04S LXPT07S LXPT00S LXPT06S LXPT09S LXPT045S LXPT048S LXPT054S LXPT060S LXPT07S For weight, dimensional and other technical information, please visit the Arresters section of 9LXPNxxxS & 9LXPMxxxS, the electrical characteristics in this table are applicable to these catalog numbers. Outline drawings can be downloaded from the GE Arrester, E-Catalog on the web. Rev. / BuyLog Catalog 4-57

58 Capacitors, Arresters and Harmonic Filters Section 4 Tranquell Intermediate Arresters Polymer High Voltage Indoor and Outdoor Service Product Description Tranquell XEP polymer intermediate arresters provide both excellent protective characteristics and temporary overvoltage capability. Gapless construction results in a design which is simple, reliable, and economical while offering excellent fault current capability to meet the most demanding service conditions. The GE Tranquell arrester is based on the field-proven metal oxide disks known for maintaining stable characteristics. Tranquell intermediate arresters are designed and manufactured in accordance with the latest revision of ANSI/IEEE C6. and IEC LPPA Polymer Polymer Arresters (Intermediate-Class) for both Indoor and Outdoor Mounting (-44 kvrms) Normally Used on System Voltage Class (L-L) Product Number (Gray Polymer) Arrester Maximum Continuous High Impedance Grounded, Solidly Grounded 4-hole NEMA Pad Eyebolt Terminal Rating Operating Voltage Capability Ungrounded (Delta), or Neutral Systems for Indoor or Outdoor for Indoor or Outdoor kvrms (L-N) kvrms temporarily ungrounded circuits kvrms Upright Mounting Upright Mounting LPPA00S 9LPPB00S LPPA006S 9LPPB006S LPPA009S 9LPPB009S LPPA00S 9LPPB00S LPPA0S 9LPPB0S LPPA05S 9LPPB05S LPPA08S 9LPPB08S LPPA0S 9LPPB0S LPPA04S 9LPPB04S LPPA07S 9LPPB07S LPPA00S 9LPPB00S LPPA06S 9LPPB06S LPPA09S 9LPPB09S LPPA045S 9LPPB045S LPPA048S 9LPPB048S LPPA054S 9LPPB054S LPPA060S 9LPPB060S LPPA07S 9LPPB07S LPPA090S 9LPPB090S LPPA096S 9LPPB096S LPPA08S 9LPPB08S /6 9LPPA0S 9LPPB0S LPPAS 9LPPBS /6 6 9LPPA44S 9LPPB44S Tranquell Arresters are designed to be operated at voltages equal to or less than their continuous capability as stated in column. For underhung or upside down mounting with eyebolt terminal on the bottom change the letter B of the catalog number to E. Application of specified rating is permissible for ungrounded or resistance grounded systems where a single phase ground may be tolerated for a substantial period of time not to exceed the Tranquell arresters overvoltage capability. For more product information, go to click on Products and Services and then Products BuyLog Catalog Rev. /

59 Capacitors, Arresters and Harmonic Filters Tranquell Intermediate Arresters Polymer High Voltage Indoor and Outdoor Service Section 4 Polymer Intermediate Arrester Protective Characteristics 9LPPAxxxS and 9LPPBxxxS Insulation Withstand Rated 0.5µsec, 0A Switching Min Wet Dry Voltage MCOV 0kA Max. IR Surge Max IR 8/0µs Maximum Discharge Voltage - kvcrest Creep Strike.xµs 0 sec min (kvrms) (kvrms) (kvcrest) (kvcrest).5ka ka 5kA 0kA 0kA 40kA in mm in mm (kv crest) (kvrms) (kvrms) Polymer Intermediate Arrester Weights and Dimensions Product Number Mounting Clearance 4-hole NEMA Pad Single Eyebolt Rated Voltage MCOV "X" Height Phase to Phase Phase to Ground Weight Line Terminal Line Terminal (kvrms) (kvrms) inches mm (in) (mm) (in) (mm) lb kg 9LPPA00S 9LPPB00S LPPA006S 9LPPB006S LPPA009S 9LPPB009S LPPA00S 9LPPB00S LPPA0S 9LPPB0S LPPA05S 9LPPB05S LPPA08S 9LPPB08S LPPA0S 9LPPB0S LPPA04S 9LPPB04S LPPA07S 9LPPB07S LPPA00S 9LPPB00S LPPA06S 9LPPB06S LPPA09S 9LPPB09S LPPA045S 9LPPB045S LPPA048S 9LPPB048S LPPA054S 9LPPB054S LPPA060S 9LPPB060S LPPA07S 9LPPB07S LPPA090S 9LPPB090S LPPA096S 9LPPB096S LPPA08S 9LPPB08S LPPA0S 9LPPB0S LPPAS 9LPPBS LPPA44S 9LPPB44S These clearances are recommended minimum clearances only and as such are not intended to take precedence over existing construction codes or specifications. Placement of the units should be such that they do not physically touch each other. Rev. / BuyLog Catalog 4-59

60 Capacitors, Arresters and Harmonic Filters Section 4 Tranquell Intermediate Arresters Polymer High Voltage Indoor and Outdoor Service Polymer Arresters (Intermediate Class) for both Indoor and Outdoor Mounting (.7-7 kvrms) 9LPPMxxxS and 9LPPTxxxS Pressure Relief Capability: 6. ka rms Energy Handling Capability:.6kJ/kV mcov Cantilever Strength:,000 inch-pounds, rated ultimate cantilever moment Product Number (Gray Polymer) Arrester Rating Maximum Continuous Voltage Eyebolt Terminal for Indoor or Indoor or cubicle kvrms Capability (L-N) kvrms Outdoor Upright Mounting Terminal Mounting. 9LPPT00S 9LPPM00S.55 9LPPT00S 9LPPM00S 4.7 9LPPT004S 9LPPM004S LPPT005S 9LPPM005S LPPT006S 9LPPM006S LPPT007S 9LPPM007S LPPT008S 9LPPM008S LPPT009S 9LPPM009S LPPT00S 9LPPM00S 0. 9LPPT0S 9LPPM0S 5.7 9LPPT05S 9LPPM05S LPPT08S 9LPPM08S 7 9LPPT0S 9LPPM0S LPPT04S 9LPPM04S 7 9LPPT07S 9LPPM07S LPPT00S 9LPPM00S 6 9 9LPPT06S 9LPPM06S 9.5 9LPPT09S LPPT045S LPPT048S LPPT054S LPPT060S LPPT07S Polymer Arresters (Intermediate Class)Protective Characteristics 9LPPTxxxS and 9LPPMxxx Product Number Rating voltage mcov kv 0.5 µsec 0 ka Switching Surge Maximum Discharge Voltage - kv crest 9LPPTxxxs kv rms rms Max IR-kV crest Max IR-kV crest.5 ka ka 5 ka 0 ka 0 ka 40 ka 9LPPT00S LPPT00S LPPT004S LPPT005S LPPT006S LPPT007S LPPT008S LPPT009S LPPT00S LPPT0S LPPT05S LPPT08S LPPT0S LPPT04S LPPT07S LPPT00S LPPT06S LPPT09S LPPT045S LPPT048S LPPT054S LPPT060S LPPT07S For weight, dimensional and other technical information, please visit the Arresters section of 9LPPMxxxs, the electrical characteristics in this table are applicable to these product numbers. Contact factory for outline drawings. For more product information, go to click on Products and Services and then Products BuyLog Catalog Rev. /

61 Capacitors, Arresters and Harmonic Filters Tranquell Intermediate Arresters Polymer High Voltage Indoor and Outdoor Service Section 4 Dimensions and Mounting Minimum Mounting Product Ratings "X" Leakage Spacing on Center (In.) Net Number Voltage kv rms MCOV Dimension (In.) Distance (In.) Ph-Ph Ph-Grd Weight (Lbs.) 9LPPT00S LPPT00S LPPT004S LPPT005S LPPT006S LPPT007S LPPT008S LPPT009S LPPT00S LPPT0S LPPT05S LPPT08S LPPT0S LPPT04S LPPT07S LPPT00S LPPT06S LPPT09S LPPT045S LPPT048S LPPT054S LPPT060S LPPT07S *9LPPMxxxs, the electrical characteristics in this table are applicable to these catalog numbers. Outline drawings are available from the factory. Rev. / BuyLog Catalog 4-6

62 Capacitors, Arresters and Harmonic Filters Section 4 Tranquell Station and Intermediate Arresters Outline Drawings Fig. - Polymer Station Arrester 9LXPA/XPBxxxAS kv through 7kV Fig. - Polymer Station Arrester 9LXPA/XPBxxxAS 90kV through 08kV Fig. - Polymer Station Arrester 9LXPA/XPBxxxAS 0kV through 44kV 4 Hole NEMA Line Terminal Fig. 4- Polymer Station Arrester 9LXPA/XPBxxxAS 68kV through 8kV Eyebolt Line Terminal For more product information, go to click on Products and Services and then Products. 4-6 BuyLog Catalog Rev. /

63 Capacitors, Arresters and Harmonic Filters Station and Intermediate Class Arresters Accessories Terminals and Mounting Brackets Section 4 The energy capability for GE Surge Arresters is defined based upon Switching Surges, milliseconds, transmission line discharges, with multiple discharges over a one-minute period and with current amplitudes that are no greater than listed below. Based upon this definition GE arresters have an energy capability as follows: Distribution, Intermediate and Station Arrester Application Arrester Rated Housing Arrester Max. Current for Energy Voltage (kv rms) Type Type Energy Rating (Amps) (kj/kv of MCOV) -6 kv Polymer Heavy Duty Distribution kv Polymer Riser Pole kv Polymer Intermediate kv Polymer Station kv Porcelain Station kv Porcelain Station kv Porcelain Station 7 Discharge Counters, Insulating Bases and Brackets Weight Description lbs kgs Product Number Discharge Counter L6FBE005E Discharge Counter with leakage current ammeter L6FBE0E Description - included, for each foot of the arrester Insulating Base for Polymer Intermediate arresters and Porcelain Station arresters 5.7 9LLGW804S -48kV rated voltage Insulating Base for Polymer Station arrester 5.7 9LLGW805S Insulating Base for Porcelain Station arrester LLGW807AS (54-60 kv rated voltage) Insulating Base for Porcelain EHV arresters (>60kV) L6AAW0S To provide assurance that all disks used in GE arresters have this capability, we perform a Low Current Long Duration Strength Test on 00% of our disks applying the above energies. We apply two groups of three shots per group. Each shot is a square wave, which is milliseconds wide. We allow 5 to 0 seconds between shots, three are applied within 60 seconds, and we allow the disk to cool between the two groups of three shots. This is followed by three shots of a half sine wave, which is 4 milliseconds wide with 5 to 0 seconds between shots. These tests weed out any weak disks and provide assurance that the disks used in the final product are indeed capable of withstanding the energy claimed. GE arresters exceed the requirements of Seismic Zone and have Cantilever Strengths and fault current capabilities as follows: Details of Discharge Counter, Models 9L6FBE005E and 9L6FBE0E (Dimensions in mm) Distribution, Intermediate and Station Arrester Application Arrester Rated Ultimate Maximum Working Fault Current Rated Voltage Housing Arrester Cantilever Strength Cantilever Strength Capability (kv rms) Type Type in-lbs N-m in-lbs N-m (ka sym) - 6 kv Polymer Normal Duty Distribution, kv Polymer Heavy Duty Distribution,000 9, kv Polymer Riser Pole 4,000 45, kv Polymer Intermediate 4,000 45, kv Polymer Intermediate 0,000,0 5, kv Polymer Station 0,000,60 0,000, kv Porcelain Station - Metal Top 70,000 7,909 8,000, kv Porcelain Station,000 6,947 60,000 6, kv Porcelain Station 00,000,596 80,000 9,08 65 Rev. / BuyLog Catalog 4-6

64 Capacitors, Arresters and Harmonic Filters Section 4 Distribution and Riser Pole Arresters 9L0 Polymer Distribution 9L7 Polymer Riser Pole 0-,000 ft. Altitude Product Description The GE Tranquell distribution and riser pole polymer line of surge arrester products provide excellent protective characteristics, temporary overvoltage capability, and switching surge energy withstand to power systems of voltages less than 46 kv rms. GE polymer arresters are ideally suited for application in both indoor and outdoor situations. They are designed and manufactured in accordance with the latest revision of ANSI/IEEE C6. and IEC Application Guide Nominal System Suggested Arrester Rating 4 Wire Wire Delta or WYE Line-to-Line Multi-Grounded Low Impedance High Impedance Voltage Neutral System Ground or Ungrounded Tranquell distribution arrester, rated 0 kv, with disconnector) -6 kv rms Polymer Heavy Duty Distribution Arresters 9L0 Note: kv rating fills positions 9 and 0 (**) of product number Product Insulating Bird X-Arm Xformer 8" Line Ground Number Bracket Disconnect Cap Bracket Bracket Lead Strap kv 6kV 9kV 0kV kv 5kV 8kV kv 4kV 7kV 0kV 6kV 9L0AXX0**AHS X X X 9L0AXX4**AHS X X X X 9L0AXA4**AHS X X X X X 9L0AXA0**AHS X X X X 9L0AXX0**XHS X X 9L0AXX4**XHS X X X 9L0AXA4**XHS X X X X 9L0AXA0**XHS X X X 9L0AXX0**BHS X X X 9L0AXX4**BHS X X X X 9L0AHA4**BHS X X X X X X 9L0AHX4**BHS X X X X X 9L0AHX0**BHS X X X X 9L0AFA4**BHS X X X X X X 9L0AFX4**BHS X X X X X 9L0AFX0**BHS X X X X 9L0BXX0**XHS X 9L0FXX0**XHS **Denotes voltage in kv. Example: kv = 0; 8kV = 8. For more product information, go to click on Products and Services and then Products BuyLog Catalog Rev. /

65 Capacitors, Arresters and Harmonic Filters Distribution and Riser Pole Arresters 9L0 Polymer Distribution 9L7 Polymer Riser Pole 0-,000 ft. Altitude Section 4-6kV rms 9L7 Polymer Riser Pole Arresters Product Insulating Bird X-Arm Number Bracket Disconnect Cap Bracket kv 6 kv 9 kv 0 kv kv 5 kv 8 kv kv 4 kv 7 kv 0 kv 6 kv 9L7HXX4**XHS X X X 9L7HXX4**AHS X X X X **Denotes voltage in kv. Example: kv = 0; 8kV = 8. Heavy Duty Distribution Arresters 9L0 Protective Characteristics Rating 0.5 µsec 0kA Switching Voltage MCOV Max. IrR Surge 8/0 Maximum Discharge Voltage (kv) Crest kv rms kv rms kv Crest Max IR-kVCrest.5kA ka 5kA 0kA 0kA 40kA Heavy Duty Distribution Arresters 9L0 Insulation and Physical Characteristics Min Power Mounting Rating Min. x µs Frequency (kv rms) Clearance "x" Center Line Center Line Weights Voltage MCOV Creep Strike Withstand Dry Wet Overall Height to Center Line to Ground (unit only) kv rms kv rms in mm in mm (kv Crest) ( sec) (0 sec) in mm in mm in mm lbs kgs Insulating Bracket w/ Bird Cap & Disconnect Insulating Bracket / Cross-arm Bracket w/ Bird Cap & Disconnect Rev. / BuyLog Catalog 4-65

66 Capacitors, Arresters and Harmonic Filters Section 4 Distribution and Riser Pole Arresters 9L0 Polymer Distribution 9L7 Polymer Riser Pole 0-,000 ft. Altitude Riser Pole Arresters 9L7 Protective Characteristics Rating 0.5 µsec 0kA Switching Voltage MCOV Max. IrR Surge 8/0 Maximum Discharge Voltage (kv) Crest kv rms kv rms kv Crest Max IR-kVCrest.5kA ka 5kA 0kA 0kA 40kA Riser Pole Arresters 9L7 Insulation and Physical Characteristics Min Power Mounting Rating Min. x µs Frequency (kv rms) Clearance "x" Center Line Center Line Weights Voltage MCOV Creep Strike Withstand Dry Wet Overall Height to Center Line to Ground (unit only) kv rms kv rms in mm in mm (kv Crest) ( sec) (0 sec) in mm in mm in mm lbs kgs Temporary Overvoltage Curves For more product information, go to click on Products and Services and then Products BuyLog Catalog Rev. /