CRoss stack LAseR GAs AnALYZeR

Transcription

1 Ross stk LseR Gs nlyzer DT SHEET ross stack laser gas analyzer (ZSS) provides continuous measurement of density of Hl contained in fl ue gas in waste incineration plant and industrial waste disposal facility, NH3 in power plant and denitration equipment, O, O2, and O2 in iron and steel plant and chemical plant with high speed response. Since ZSS is installed directly on the fl ue(pipe) where objective gas fl ow to be measured, preparation is not required for measured gas to be introduced to the analyzer, which is required for sampling method. This analyzer can be used under high dust conditions, so it is possible to install upstream of the bagfi lter where gas sampling is normally diffi cult. This is the fi rst laser gas analyzer for environment and process in Japan produced by Fuji. Receiver unit ontrol unit ZSS FetuRes. Maintenance free thanks to using the long-term stable parts. 2. Running cost is minimized by no need of gas sampling devices and having few parts to replace. 3. Long and high stability due to almost no drift. 4. Since adopting the near-infrared semiconductor laser which emit light of the wavelength of measured component, hardly affected by interference of other gas.. It is suitable for injection control of slaked lime, measuring the residual ammonia gas and monitoring and control of converter furnace of combustible gas recovery due to high-speed response for to seconds.(high-speed response type: to 2 seconds) 6. It is measurable at high temperature and dust circumstance. In addition performance of dust resistance has been improved. 7. It is environment-friendly product. ecause power consumption is V or lower when V. speifitions Measurement principle: Non-dispersive infrared absorbance system (NDIR) Measuring method: ross-stack system (path system) use application: Waste incineration plant, industrial waste disposal facility, power plant iron and steel plant, paper plant, pulp mill, chemical plant and bioplant etc Light source: Near-infrared laser Laser class: lass (excluding some of O2 meters) outline (D W H) mm: Receiver unit (8 x approx.4 x approx.mm) Transmitter unit (24 x approx.4(432) x approx.6mm) ontrol unit (37 x2 x 44mm) Transmitter unit Mass: Receiver/Transmitter unit: pprox. kg ontrol unit: pprox. 8kg structure: Outdoor use type, dustproofi ng/rainproofi ng structure (IP6) ox finish color: Receiver/Transmitter box: gray ontrol unit cover: blue ontrol unit case: silver Measurable component and range: omponent Min. measuring Max. measuring range range Hl ppm ppm Hl+H2O (*) ppm (Hl) ppm (Hl) NH3 ppm ppm NH3+H2O (*) ppm (NH3) ppm (NH3) O2 (low output type) 4 vol% vol% O2 (For use in high dust) 4 vol% vol% O2 (For combustion control) 2 vol% 2 vol% O 2. vol% vol% O (For use in high temperature) vol% vol% O2 2. vol% vol% O2 (For use in high temperature) vol% vol% O+O2 2. vol% vol% O+O2 (For use in high temperature) vol% vol% H4 ppm vol% (*) Range for H2O is fi xed at vol% m. (Range in the case stack (optical path length) diameter is m) Max. and min. ranges for each stack diameter = (Max. and min. ranges when stack diameter is m) Stack diameter EDS3-3g Date Dec. 26, 22

2 ZSS * Stack diameter = Optical path length (Example: In case stack diameter is 2m for Hl measurement, Max.range: 2ppm and min. range: ppm). Material: Receiver unit / Transmitter unit: luminum, SUS36 ontrol unit: luminum Materials of gas-contacting parts: SUS36, K7, FKM, PTFE, glass-cloth, silicone ir purge connection diameter: R/4 (tube ø8 6) Power supply: Rated voltage to 24V ±% Rated frequency /6 Hz Power consumption: Max. rated power: pprox. 7V or less alibration interval: Once every six months (Maintenance cycle may vary depending on the operating environment.) Indicator (control unit): LD with back light ommunication functions: US (for loader), RS-48 (Modbus protocol) able length: Receiver unit to Transmitter unit: Standard 2m (Maximum 2m) Receiver unit to control unit: Standard m (Maximum m) nalog output: 4 to 2m D or to V D x 2 (4) Isolated output indicated in the parenthesis is optional. ( to V D, to V or to V is available.) llowable load: 4 to 2m D Ω or less, to V D kω or more (Output measurement value and O2 corresponding value. verage value and instantaneous value are switchable by the settings.) nalog input: 4 to 2m D x 2 (6) Note: Number in parenthesis is option. Measured gas pressure, measured gas temperature, measured gas velocity, O2 gas concentration, water concentration, air purge pressure (Measurement concentration correction, O2 correction or alarm output is performed according to the input signal.) ontact output: Relay contact output (contact capacity 24V D (V.)a or b (Standard: a, b: for power supply off only) Low light transmission, outside the range of upper/lower limits, device failure, during hold/during calibration, power supply off. ontact input (option): Photo coupler receiver contact input (operating voltage 2 to 24V D / to 2m) 3 verage value reset signal, switching instantaneous value/ moving average value and remote hold larm output (screen-displayed): LD failure, LD temperature error, high gas temperature, air purge (low pressure), box temperature warning, low light transmission, PD over range, connection error, I under, Range (H-Limit) or Range (L-Limit) Display contents: omponent, concentration (instantaneous value, average value O2 correction instantaneous value and O2 correction average value), alarm (fault status) contact output contents (a contact) Low light transmission: ontact output is performed (close) when the amount of light transmission is insufficient. Outside the range of upper/lower limits: ccording to the preset upper or lower limit alarm value, contact output is performed (close) when it becomes lower than alarm upper/lower limit. Device failure: ontact output is performed (close) when laser failure, laser temperature control failure, exceeding the amount of light transmission or communication error are occurred. During hold/during calibration: While O output is held by the hold setting, the values, output (close) of which is held, is the ones just before the holding or arbitrary set values. Output (close) during calibration Power supply off: Output (close) while power supply is off ontact Input ontents (option) verage value reset signal: Output of converted average value is started from the initial state by applying rectangular-wave voltage (pulse width 2 sec or more) to the input terminal of average value resetting. Output is reset by inputting and restarted by opening. Switching instantaneous value/moving average value: Switching to and from the instantaneous value and the average value of the analog output is performed by applying rectangular-wave voltage (pulse width 2 sec or more) to the input terminal for switching between the instantaneous value and the moving average values. Remote hold: The analog output is held by applying rectangular-wave voltage (pulse width 2 sec or more) to the remote hold input terminal, and restarted by applying it again. Functions O2 correction: onversion of measured Hl, NH3 and O gas concentrations into values at standard O2 concentration orrection formula: 2 On = s 2 Os : onverted concentration s:measured concentration of sample gas Os:Measured O2 concentration (Upper limit settable to 2% O2) On:Standard O2 concentration (value changeable by setting; to 9% O2) The result of calculation is indicated and output in an analog output signal. Installation Environment mbient temperature: 2 to (Receiver unit/transmitter unit), to 4 (control unit) mbient humidity: 9% R.H. or less Measurable optical path length (inner diameter of stack):. to m Standard flange: JISK flange (JIS 222) 2

3 Purge: Instrument air (compressor must be installed when power supply cannot be provided. Does not contain oil and mist). N2 for O2 meter except O2 for combustion control.pressure.mpa or more depending on measured gas velocity. Purge flow rate: 2L/min or more (depending on measured gas temperature, velocity, pressure, moisture and dust) One-side air purge flow rate: (L/min) = Gas flow rate (m/s) (in case of pipe) Measured gas condition: Temperature: 3 or less (H4, O,O2, O+O2, O2 for low output type) 4 or less (Hl) 3 to 4 (Hl+H2O) 4 or less (NH3) 3 to 4 (NH3+H2O) 2 or less (O2 for use in high dust, O for use in high temperature gas, O2 for use in high temperature gas, O+O2 for use in high temperature gas) 4 to 2 (O2 for combustion control) Pressure: ±kpa (O2 for combustion control is -kpa to kpa) Moisture: vol% or less (or Should not be saturated water vapor.) Velocity: Range of purge flow rate (gas flow rate (m/s) = one side flow rate (L/ min / ) Note) When measuring high-temperature gas at or higher, install a pressure sensor on the air-purge unit to monitor air purge. If measurement is taken while purge is not performed, the device may be damaged. Dust: to 4g/m 3 (N) (depending on environmental conditions such as measuring component, equipment specification, light path length and particle diameter). In case of high dust environment, consult with Fuji. Vibration:.G or less (.2G or less when the frequency range is 2 to 4Hz) (when optical path length is m) Mounting angle: Horizontally ± degrees or less (No dew condensation should accumulate on the window.) Performance (Except for H2O) Repeatability: ±.%FS (depending on measuring component and measuring range) Linearity: ±.%FS (depending on measuring component and measuring range) Zero drift: ±2.% FS (NH3 ±3.%, FS when range is 2ppm or less) Interference from other gas components: ±2.%FS (The gasses which have no absorption within the wavelength range of measured gas (several tens pm) do not interfere in principle). Minimum detectable limit: % of minimum detectable limit Response time (9% FS response): to seconds (high-speed type: approx. to 2seconds) Warm up time: 9 minutes or less (* Excluding influenced range with absorptive gases such as Hl and NH3) E directive compliance Low voltage safety: EN6-(2) Electromagnetic: "Installation ategory II" compatibility EN6326-(26) EN (26) EN6-3-2(26) EN6-3-3(99), (2), 2(2) asic principle Near-infrared semiconductor laser is adopted for the light source and photo-diode is adopted for photo-detection. Each measured gas component has its own wavelength range where the gas absorbs the light (see the figure below). The wavelength range consists of a set of many absorption lines, and one of these lines is used for measurement. s measurement is performed in this very narrow wavelength range, no other gas does not have an interference in principle. To detect the gas concentration, used is not a variation of light intensity, but intensity of modulated signal amplitude. 7nm nm 2nm nm 7nm 2nm 22nm Wavelength bsorption intensity O2 HF HF bsorption line used for measurement H2S NH3 H4 Hl H2S NH3 O2 NH3 bsorbing spectrum map of measuring gases 72nm 74nm 76nm 78nm 8nm 82nm 84nm bsorption lines of Hl Wavelength NO N2O N2O O 3

4 4 ZSS ODE SYMOLS When ordering, be sure to submit the order sheet on the last page of this Data Sheet. Digit Measurable components Unit Measuring range Modification No. Flange rating Number of analog output points Number of analog input points nalog output ontact output/input able length between receiver and control unit able length between receiver and transmitter Display and operation manual Measuring optical path length (unit: m) Measuring optical path length (unit:.m) Measuring optical path length (unit:.m) Dust proof specification High-speed/ G Specification O O (For use in high temperature) Hl Hl+H2O O2 O2 (For use in high temperature) O+O2 O+O2 (For use in high temperature) O2 (low output type) O2 (For use in high dust) O2 (For combustion control) H4 NH3 NH3+H2O ppm mg/m 3 vol% to 2 to 2. to 4 to to to to 2 to 2 to to to 2 to 2 to 4 to to to 2 to to 6 Others K (JIS 222) K DN/PN NSI # 2 2 points 4 points 2 points 6 points 4 to 2m D to 2m D to V D to V D to V D output points, No input output points, 3 input points m m 2m 3m 4m m 8m m Others 2m m m m 2m 2m Others Japanese English hinese ZSS Note Note Note, 2 Note Note Note 2 Note 3 Note 2, 3 Note 4 Note Note Note Note 6 Note 7 m Note 8 m 2m 3m 4m m 6m 7m 8m 9m.m Note 8.m.2m.3m.4m.m.6m.7m.8m.9m.m Note 8.m (Used only when m is specified) Standard Note 9 Dust proof Standard Note High-speed/G Y F G H K L P Q T R W X 3 K Q S L V T D J E F G H M X Y D D E F G H X D E F X J E N D N H Note ) When you order the Hl meter, O meter and NH3 meter, Specify the conversion basis of O2 concentration (settable within to 9vol% O2: Integer) Note 2) When gas temperature is or more, specify the the type for use in high temperature Note 3) Specify the same range for O and O2. If different range is desired for O and O2, specify the "X" at 6 digit and give a description of each range. Note 4) Only use where gas temperature is 4 or more Note ) Specify the range within the max/min range calculated from path length. If the range exceeds that "the measuring range x the stack length" (optical path length), consult Fuji. Note 6) Others of cable length between receiver and control unit. When specify the "X" at 4th digit, m or more is only selectable. Note 7) Others of cable length between receiver and transmitter. When specify the "X" at th digit, m or more is only selectable. Note 8) If it is m, specify the "9" at 8th digit, "9" at 9th digit and "9" at 2th digit. Note 9) Specify the "D" at 2st digit if "N" is specified at 22nd digit and use under circumstances dust is g/m 3 N) or more. Note )When "H" is specified at 22nd digit, specify the "N" at 2st digit. How to specify measuring optical path length Example: 2.2m 2 for 8th digit, 2 for 9th digit and for 2th digit m 9 for 8th digit, 9 for 9th digit and 9 for 2th digit

5 LIST FOR OMINTIONS OF MESURLE OMPONENTS, UNITS ND MESUREMENT RNGES Measurable component 4th digit Measurable range 6th digit Measurable range 6th digit (Unit: When th digit is or 3) (Unit: When th digit is ) O N/ K, Q, S, L, V,,, T,, X O (For use in high temperature) N/ V,,, T,, X H V,,, T,,,, D, J, E, F, G, H, X N/ H+H2O F,,, D, J, E, F N/ O2 G N/ K, Q, S, L, V,,, T,, X O2 (For use in high temperature) H N/ V,,, T,, X O+O2 K N/ Q, S, L, V,,, T,, X (O) N/ Q, S, L, V,,, T,, X (O2) O+O2 L N/ V,,, T,, X (O) (For use in high temperature) N/ V,,, T,, X (O2) O2(low output type) P N/ S, L, V,,, T,,, X O2(For use in high dust) Q N/ S, L, V,,, T,, X O2(For combustion control) T N/ T,,, X H4 R,, D, J, E, F, G, H, M, X K, Q, S, L, V,,, T,, X NH3 W,, T,,,, D, J, E, F, G, H, X N/ NH3+H2O X,,, D, J, E, F N/ Scope of Delivery Receiver box Transmitter box ontrol unit ngle adjustment mechanical section (required 2 units, one for receiver and the other for transmitter) able between receiver unit and transmitter unit (specified length) Optional Items Spare parts for one year (ZNSS2) alibration gas cell (*) (*2) able between receiver unit and transmitter unit (For calibration) (*) able between receiver unit and control unit (For calibration) (*) Standard gas (ZM), pressure regulator (ZD) able between receiver unit and control unit (specified length) Hexagon socket head cap screw ( onnecting bolt between angle adjustment mechanical section and receiver box) Standard accessory set, instruction manual Recorder (when necessary, Fuji's product type PHL/PHR, etc.) Others *: One set of the cables and calibration gas cell are necessary for installation and annual maintenance. *2: Standard length m (2mm or mm when the measuring range is low concentration) Standard accessories Name Quantity Specification olt 8 (6) M6 (7) SUS (*) Nut 8 (6) M6 SUS (*) Spring washer 8 (6) M6 SUS (*) Flat washer 8 (6) M6 SUS (*) ompanion flange packing or flange packing specified for use 2 ccording to flange specifications in high temperature olt for angle adjustment 6 Hex socket bolt M8 7 Power supply fuse 2 Instruction manual (*When "" or "" is specified in the 9th digit in a code symbol, quantity is 6 pieces. 8 pieces are attached in other cases.) (*When "", "" or "D" is specified in the 9th digit, olt length is 7mm. It is mm in other cases. Inch-sized bolts are not applicable.) Spare Parts for One Year (ZNSS2) Name Quantity Remarks Silicon packing 2 pieces For bellows (ZZP*ZSSTK7N38P) O-ring 2 pieces (ZZP*ZSSTK7P23P)

6 ZSS alibration/installation fixtures list (Option) Parts name Quantity Type () able between receiver unit and control unit (for calibration) ZZP*ZSSTK4J272 (2) able between receiver unit and transmitter unit (for calibration) ZZP*ZSSTK4J643 (3) alibration gas cell (*3) (Hl, NH3, O,O2, O+O2,H4) ZZP*ZSSTK4J3676 alibration gas cell (*3) (Hl+H2O, NH3+H2O, O2) ZZP*ZSSTK4J26 (4) Optical axis adjusting tool (laser pointer, target) ZZP*ZSSTK4J274 () IR card (for NH3) ZZP*ZSSTK7N4P (6) heck cell ZZP*ZSSTK4J26 (7) Filter regulator ZZP*ZSSTK7N7466P (8) Mist separator ZZP*ZSSTK7H849P (9) R/4 stopper (plug) for mist separator ZZP*ZSSTK7384P7 Flow meter (2 to L/min) (*4) ZZP*ZSSTK7N4624P () Flow meter (4 to L/min) (*4) ZZP*ZSSTK7N4624P2 Flow meter (3 to 3L/min) (*4) ZZP*ZSSTK7N8849P ir-set box (2 to L/min) ZZP*ZSSTK7N668 () ir-set box (4 to L/min) ZZP*ZSSTK7N6682 ir-set box (3 to 3L/min) ZZP*ZSSTK7N6683 ir purge mechanism (2 to L/ ZZP*ZSSTK7P433 min) (2) ir purge mechanism (4 to L/min) ZZP*ZSSTK7P4332 ir purge mechanism (3 to 3L/min) ZZP*ZSSTK7P4333 N cable for optical axis adjustment (3) ZZP*ZSSTK7P224 * 3: Standard length m (2mm or mm when the measuring range is low concentration) * 4: Usually, 2 units are required to adjust each air purge for receiver unit and transmitter unit. (3) alibration gas cell / about mm (2) able between receiver and transmitter (approx. 6mm) () able between receiver unit and control unit Stack (4) Optical axis adjusting tool (target) Parts used for calibration (4) Optical axis adjusting tool (laser pointer) Parts for adjusting the optical axis Transmitter unit () IR card IR RD Laser beam (visible) Invisible light Invisible light / visible fixtures(for NH3) Receiver unit (6) heck cell Transmitter unit Stack ontrol unit Laser gas analyzer with check cell (ZSS) SV3 tmospheric release SV SV2 (O) Sequencer Remote check input (I) N2 cylinder Standard gas cylinder Supplies for checking span value on site 6

7 () ir set box 4-φ (Mounting hole) (7) Filter regulator Parts for air purge (8) Mist separator Flow meter ox Mist separator Filter regulator Pipe with external diameter φ (out of supply scope) Receiver purge outlet Transmitter purge outlet measuring instrument air inlet Drain outlet (φ piping) (not supplied by us) () Flow meter Measuring instrument air inlet Rc/4 Piping system diagram Receiver purge outlet Rc/4 Transmitter purge outlet Rc/4 8 2 Drain outlet Piping retainer for φ (2) ir purge mechanical part total 2m m Piping material: φ8/6 Teflon pipe.m.m for φ8 tube (metallic tube recommendable) to Transmitter purge inlet to Receiver purge inlet to Receiver purge inlet Mist separator Filter regulator Measuring instrument air inlet (oupling joint) Piping system diagram (3) N cable for optical axis adjustment 7

8 ZSS OUTLINE DIGRM (Unit : mm) 2-Flowmeter (option) Or air-set box opper or SUS pipe (not supplied) Instrumentation airline joint (not supplied) φ8/6 Teflon pipe (not supplied) 2 to L/min Filter regulator (option) Instrumentation air inlet Receiver box (2 8 ) pprox. 4 Flange of angle adjustment Purging gas inlet (with bell-and-spigot joint for φ8/6) to 2 6 With bolt and nut to 2 (M6 ) Flange pipe to mount stack (not suppried) Stack Mist separator (option) pprox. 4 (432) Note Flange of angle Transmitter box adjustment (6 24 ) Purging gas inlet 2 φ. to m 6 φ34 (onnector) Receiver unit φ2 JISK FF (with packing) φ4 Transmitter unit able between receiver unit and transmitter unit (standard : 2m) 74 2-φ2 φ34 (onnector) φ ontrol unit Note : e sure to set the R/4 sealing plug (ZZP*ZSSTK7384P7) on the drain outlet of the mist separator. 42 φ3 Power supply 34 3 I7-Waterproof grand (Internal diameter φ2) able length (2mm) onnector able between receiver unit and control unit (standard : m) DI/OO74 2 Mounting diagram e sure to prepare instrument air (N2 for an O2 meter (for low output type/ high dust)). If mixed air such as oil and mist contained is used, contamination occurs in the pipe of flow meter and purge flow rate falls, which will affect the measurement. ccording to above, maintenance is required frequentlyand filter may be installed additionally depending on situation. Note) ir or nitrogen purge should be performed if the equipment is installed in a flue whether or not it is operated. n case operate the flue without performing purge, it may cause the fatal damage to the optical part. LSER GS NLYZER ZSS 8

9 EXTERNL ONNETION DIGRM (When number of analog output is 2 points) There are two types of output/input terminal. Power supply terminal 2 3 to 24 V (/6Hz) FG Screw diameter : M4 O terminal Screw diameter : M2 or the equivalent O+ 2 O- nalog output 2 O2+ 22 O2- nalog output 2 l terminal Screw diameter : M2 or the equivalent 3 I+ 4 I- nalog input 23 I4+ 24 I4- nalog input 4 (I extension board is required) I2+ 6 I2- nalog input 2 2 I+ 26 I- nalog input (I extension board is required) 7 I3+ 8 I3- nalog input 3 (I extension board is required) 27 I6+ 28 I6- nalog input 6 (I extension board is required) DI/DO terminal Screw diameter : M2 or the equivalent 9 DO DO Low light transmission 29 DO7 3 DO7 DO2 2 DO2 Device failure 3 DO8 32 DO8 Power supply off 3 DO3 4 DO3 During hold / during calibration 33 DI 34 DI verage value reset signal (option) DO4 6 DO4 Outside the range of upper / lower limits 3 DI2 36 DI2 Switching instantaneous value/moving average value (option) 7 DO 8 DO 37 DI3 38 DI3 Remote hold (option) 9 DO6 39 DI4 2 DO6 4 DI4 Note) Unassigned terminal may be connected to internal circuit. So they should not be used as repeating terminals. 9

10 ZSS External connection diagram (when number of analog output is 4 points) Power supply terminals 2 3 to 24V /6Hz FG Screws diameter: M4 O terminal O4 Unassigned Unassigned O+ 2 O- 3 O2+ 4 O2- nalog output nalog output 2 O3+ 6 O3-7 O4+ 8 O4- nalog output 3 O extension board is required) nalog output 4 O extension board is required) + - O O2 O3 I terminal I4 I I I I2 I3 I+ 2 I- 3 I2+ 4 I2- I3+ 6 I3- nalog input nalog input 2 nalog input 3 (I extension board is required) 7 I4+ 8 I4-9 I+ I- I6+ 2 I6- nalog input 4 (I extension board is required) nalog input (I extension board is required) nalog input 6 (I extension board is required) DI/DO terminal DI 2 DI 3 DI2 4 DI2 DI3 6 DI3 7 DI4 8 DI4 9 DI DI 3 DO 4 DO DO2 6 DO2 7 DO3 8 DO3 verage value reset signal (option) Switching instantaneous value/moving average value (option) Remote hold (option) Low light transmission Device failure During hold/during callibration 9 DO4 2 DO4 2 DO 22 DO 23 DO6 24 DO6 2 DO7 26 DO7 27 DO8 28 DO8 29 DO9 3 DO9 3 DO 32 DO 33 DO 34 DO Outside the range of upper/lowerlimits Power supply off Note) Unassigned terminals may be connected to internal circuit. So they should not be used as repeating terminals.

11 MOUNTING DIMENSIONS (Unit: mm) Do not install the device in a stack if air purge is not performed. It may become unusable because the window will get dirty. Stack c d a b Flange pipe to mount stack (*9) e a: Inner diameter of φmm or more b: 2 to 7mm (*) c: pproximately 2 to 2mm (*6) d: 4mm or more (*7) e: to mm (*7) Scaffold (*8) *: When used in an enviroment with high dust, reserve at least mm. *6: When internal gas temperature is high, reserve the distance of 2mm or more. Note that, adjustable angle range narrows down, so mounting angle of flange pipe to mount stack should be adjusted accurately. *7: Sufficiently secure a space for installation which permits easy operation. *8: Scaffold is required for the both side of receiver unit and transmitter unit. *9: Use a flange provided with a valve where there is a risk of gas injection or the operator may be exposed to dangerous situation. *: Tighten the flange with a torque of 8±4N-m. When tightening the flange, apply grease to the bolts (recommendable to use grease containing molybdenum). Rough guide to mount the companion flange When θ is larger than, mount it within the γ angle ( ) inside the circle with the radius. Y γ θ X Z X: Inner diameter of flange of receiver unit and transmitter unit Y: Length of flange of receiver uit and transmitter unit Z: Length of stack γ, θ = TN X 2 (Y + 2).87 (Z + Y + 2)

12 ZSS Please specify the following items when you contact us for inquiry.. ode symbol ZSS 2. Parameter of measured gas Item Min. value Typical value Max. value Measured gas concentration Temperature ( ) Pressure (kpa) Flow (m/s) Moisture (vol%) Dust (mg/m 3 (N)) Other gas component (vol%/ppm) Other gas component (vol%/ppm) Other gas component (vol%/ppm) 3. Stack diameter (Inner diameter) (measured optical path length) m 4. Length from stack (inner diameter) to flange m. Length from stack (inner diameter) to flange m 6. able between receiver unit and control unit. D m 7. able between receiver unit and transmitter unit. E m Instrumentation air Instrumentation air Stack Receiver unit Transmitter unit ontrol unit E D 8. Spares for -year measurement no need necessary 9. Optional items no need necessary.output of O2 correction value (for only Hl, NH3 and O meter) no need necessary.oxygen correction reference value (%) (When "necessary" is selected in 8) % 2.Vibration no need necessary ( G) aution on Safety *efore using this product, be sure to read its instruction manual in advance. International Sales Div Sales Group Gate ity Ohsaki, East Tower, -2, Osaki -chome, Shinagawa-ku, Tokyo 4-32, Japan Phone: , 728 Fax: Information in this catalog is subject to change without notice. Printed in Japan