VS192F111-4 LED DOT MATRIX MODULE

Size: px

Start display at page:

Download "VS192F111-4 LED DOT MATRIX MODULE"

Aubrey Cooper
5 years ago
Views:

1 VISSEM ELECTRONICS CO., LTD R&D DIVISION 395, Cheongdeokdong, Giheunggu, Yongincity, Gyeonggido, KOREA TEL: ~29,20 FAX: ~1 LED DOT MATRIX VS192F1114 1ⅹ1 Type ISSUED DATE ITEM DESIGN CHECK APPROVAL VER FV VER FV SIGNATURE DATE

2 1.MODEL NAME : VS192F FEATURES Structure ITEM Display Color Size(W X H X D) Dot Pitch Number Of Dots Leds Per Dot Weight Drive Mode Application DESCRIPTION Full Color 192 X192 X16(mm) 12(mm) 256(16 16) Dots R:1, PG:1,B:1(3In SMD LED) Max.580(g) 1/4 Duty Drive INDOOR 3. ABSOLUTE MAXIMUN RATINGS ITEM SYMBOL VALUE UNIT REMARK Supply Voltage V LED 0~+5.5 V CC 0~+6.0 Signal Input Voltage Level V IH, V IL 0.3~ V CC +0.3 V Operating Temperature T OP [1] 20 ~ +50 On Dots=100% 20 ~ +60 On Dots=30% Storage Temperature T stg 25 ~ +80 NOTES : [1] Temperature of led surface s should be remained below 70 in case of necessity, led system requires cooling fan. Maintained at less than 80% relative humidity, and no dew condensation shall take place. V 4. RECOMMENDABLE OPERATING CONDITIONS ITEM SYMBOL MIN. TYP. MAX. UNIT REMARK Supply Led V LED Voltage Logic Circuit V CC V V IH 0.8 V CC V CC Signal Input Voltage Level V IL V CC Operating Temperature T OP 15 ~ ELECTRICAL CHARATERISTICS (AT T a = 25 ) ITEM SYMBOL VALUE UNIT REMARK Clock Frequency F MAX.16 MHz Current Consumption For Module l LED I IC MAX.5.5 A ALL On MAX.0.5 VS192F /14

3 6. OPTICAL CHARACTERISTICS( AT T a = 25 ) ITEM SYMBOL MIN. TYP. MAX. UNIT REMARK RED 830 Brightness Wavelength Viewing Angle [REFERENCE] GREEN 2,700 L V BLUE 250 WHITE 3,700 RED GREEN λ p BLUE HOR θ 1/2 VER. 120 These are just brightness of standard model. If you have any cd/ m2 nm deg( ) Half Value questions about higher brightness, Please contact us. 7. SIGNAL FUNTION 1) DATA SIGNAL CONNECTOR PIN MAP (IN) PIN NUMBER PIN NAME FUNCTION DESCRIPTION TOP VIEW 1, 2, 3, 4 R1, R2, R3, R4 Data Input For Red Color 5, 6, 7, 8 G1, G2, G3, G4 Data Input For Green Color 9, 10, 11, 12 B1, B2, B3, B4 Data Input For Blue Color 13[LSB], 14[MSB] A[0:1]_IN 2BIT Line Address 15 SCLK_IN Shift Clock For Input Data 16 LATCH_IN Data Strobe 17 DEN Line Decoder Enable Signal 18 GCLKR Clock Input for Red Gray Scale 20 GCLKG Clock Input for Green Gray Scale 22 GCLKB Clock Input for Blue Gray Scale 19, 21 GND Ground Of The Module PIN MAP (OUT) PIN NUMBER PIN NAME FUNCTION DESCRIPTION TOP VIEW 1, 2, 3, 4 R1, R2, R3, R4 Data Output For Red Color 5, 6, 7, 8 G1, G2, G3, G4 Data Output For Green Color 9, 10, 11, 12 B1, B2, B3, B4 Data Output For Blue Color 13[LSB], 14[MSB] A[0:1]_OUT 2BIT Line Address 15 SCLK_OUT Shift Clock For Output Data 16 LATCH_OUT Data Strobe 17 DEN Line Decoder Enable Signal 18 GCLKR Clock Output for Red Gray Scale 20 GCLKG Clock Output for Green Gray Scale 22 GCLKB Clock Output for Blue Gray Scale 19, 21 GND Ground Of The Module VS192F /10

4 2) POWER CONNECTOR PIN MAP(POWER) PIN NUMBER PIN NAME FUNCTION DESCRIPTION 1 V CC Supply Voltage For IC 2, 3 V LED Supply Voltage For LED TOP VIEW No.1 4, 5, 6 GND Ground Of The Module 3) CONNECTOR CABLE SPECIFICATION DATA CABLE 22 PIN Cable (Pitch 2.00mm) 15MM 140mm 15MM POWER CABLE 200MM CONNECTOR VENDOR MODEL NO. SPECIFICATION HOUSING MODEL NO. IN,OUT DATA DONCONNECX C06S22ASA1G 22PIN, 2mm PITCH A05G22BSA1G102 POWER YEONHO SMW20006G 6Pin 2mm Pitch SMH20006 This connectors can be changed without a previous notice for quality improvement. VS192F /10

5 8. SIGNAL & POWER CABLE CONNECTION 1) DIRECTION OF DATA FRONT VIEW DIRECTION OF DATA SHIFT (A) (B) 2)SIGNAL CABLE CONNECTION EXAMPLE REAR VIEW INTERFACE CONNECTOR & CABLE CIRCUIT IN OUT (1,1) (1,2) (1,3) (1,4) IN OUT (2,1) (2,2) (2,3) (2,4) RED1~4, GREEN1~4, BLUE1~4_DATA, SCLK, LATCH, LINE ADDRESS(A0~A1), GCLKR, GCLKG, GCLKB VS192F1114 IS CONSIST OF 1PCS 192Ⅹ192mm(16Ⅹ16 Dots) DEN, GND VS192F /14

6 9. BLOCK DIAGRAM A0 A1 GCLKR GCLKG RED1 A0_OUT A1_OUT GCLKR_OUT GCLKG_OUT RED1_OUT RED2 RED2_OUT RED3 RED3_OUT RED4 RED4_OUT GRN1 R_VR GRN1_OUT GRN2 GRN2_OUT GRN3 GRN3_OUT GRN4 GRN4_OUT G_VR 2 TO 4 16Ⅹ4 LED DOT MATRIX LINE DECORDER 16Ⅹ4 LED DOT MATRIX & DRIVER 16Ⅹ4 LED DOT MATRIX 16Ⅹ4 LED DOT MATRIX BLUE1 BLUE1_OUT BLUE2 BLUE2_OUT BLUE3 BLUE3_OUT BLUE4 BLUE4_OUT GCLKB LATCH CLOCK DEN B_VR GCLKB_OUT LATCH_OUT CLOCK_OUT DEN_OUT VS192F /14

7 10. TIMMING CHART VS192F /14

8 Switching Characteristics Vcc=5V, Ta=25 Characteristics Symbol condition Min. Typ. Max. Unit SDI DCLK t SU0 1 ns Setup Time LE DCLK t SU1 1 ns LE DCLK t SU2 5 ns Hold Time Propagation Delay Time Staggered Delay of Output Pulse Width DCLK SDI t H0 3 ns DCLK LE t HI 7 ns DCLK SDO GCLK OUT4n* LE SDO OUT4n+1* OUT4n+2* OUT4n+3* LE t PD0 t PD1 t PD2 ** t DL1 t DL2 t DL3 t W(L) V DD =5V V IH =V DD V IL =GND R EXT =700Ω V DS =1V R L =200Ω C L =10pF C 1 =100nF C 2 =10uF C SDO =10pF ns ns ns ns ns ns ns DCLK t W(DCLK) 15 ns GCLK t W(GCLK) 15 ns Output Rise Time of Output Ports t OR ns Output Fall Time of Output Ports t OF ns Error Detection Minimum Duration t EDD ns Refer to the Timing Waveform, where n=0, 1, 2, 3 In timing of Read Configuration and Read Error Status Code, the next DCLK rising edge should be t PD2 after the falling edge of LE. VS192F /14

9 Principle of Operation Control Command Signals Combination Description Number of DCLK Command Name LE Rising Edge when The Action after a Falling Edge of LE LE is asseted Data Latch High 0 or 1 Serial data are transferred to the buffers Global Latch High 2 or 3 Buffer data are transferred to the comparators Read Configuration High 4 or 5 Move out "configuration register" to the shift registers Enable "Error detection" High 6 or 7 Detect the status of each output's LED Read "Error status code" High 8 or 9 Move out "error status code" of 16 outputs to the shift registers Write Configuration High 10 or11 Serial data are transferred to the "configuration register" Reset PWM Counter High 12 or13 If bit "B" of the configuration register is set to "1", this command will reset PWM counter. VS192F /14

10 Definition of Configuration Register MSB LSB F E D C B A Ex) Default Value F E D C B A b Bit Attribute Definition Value Function F Read/Write Data Loading E Read Thermal error flag 0(Default) 15 times of "data latch" +1 "global Latch" 1 16 times of "data latch" +1 "global Latch" 0(Default) Safe(OK) 1 Over temperature(>150 typ.) D Read X 1 Reserved bit C Read/Write PWM counting mode selection 0 1(Default) 64times of MSB* 6bit PWM counting plus once of LSB 6bit PWM counting 12bit PWM direct counting 0(Default) Disable B Read/Write PWM counter reset 1 Enable with 12 or 13 DCLKs(rising edge) when LE is asserted PWM data 0 Autosynchronization A Read/Write synchronization mode 1(Default) Manual synchronization 9~2 Read/Write current gain adjustment ~ 'b (Default) 1 Read/Write Thermal protection 0(Default) Disable 1 Enable, 25% of setting output current if T TF >150 0 Read/Write Timeout alert of GCLK disconnection 0(Default) Enable 1 Disable Please refer to Setting the PWM Couting Mode Section.(Next Page) VS192F /14

11 Setting the PWM Gray Scale Counter LED Driver ic provides a 12bit color depth. The value of each 16bit serial data input will be valid only for 12bits and implemented according 12bit PWM counter. Setting the PWM Counting Mode VS192F /14

12 11. DIMENSION VISSEM VISSEM VISSEM VISSEM VS192F /10

13 Plate Work 2By2 Array ** Hole for assemble between unit case and module. VS192F /10

14 12. SAFETY Precautions in installing LED Module 1. Please escape the place where electromagnetic wave and noise is, which might cause malfunction to LED module, when install LED Display Board. 2. Since over voltage and reverse voltage might cause the problem in internal circuit and LED, please make sure and check the input voltage range, before operation. 3. Please escape the high humidity and leakage place which cause the LED module to be broken. 4. The temperature of the surface of LED module shall be under 70 during operation. 5. Heating from LED might cause damage in LED module or/and malfunction in LED display board, user shall prepare suitable ventilation and cooling facility. 6. Even though the brightness become lower and lower, after long time use, it's prohibited to input over voltage in order to increase the brightness, which might cause severe damage to LED Module. For the best operation, user shall operate LED module according to data sheet. 7. Please turn off the power supply, when display data are not charged. 8. Please be careful not to exposure LED Module to the dust, dirt, base, gas and other noxious gas, when install LED Display. 9. User shall consider the weight of LED module enough, when prepare steel structure and install LED Display Board. VS192F /10

15 Precautions in installing LED Module 1. Any jumper and switch is set up properly before delivery, please do not modify or/and change setting without consulting with manufacturer. 2. The circuit part of LED Module include CMOS components, please treat carefully with consideration of static electricity 3. Impact and vibration to LED Module might be the reason of disconnection and dot off, please escape those factors. 4. It's highly recommended to escape the high temperature & humidity and be careful not to exposure LED module to dust, dirt, base and SO2 Gas and other noxious Gas in order to escape the potential problem. 5. Please be careful not to be scratched and hurt on the surface of LED module. 6. It's prohibited to clean up LED module with solvent. In order to clean up LED module, it's highly recommended to use a piece of dried cloth and smooth brush. 7. Stacking LED modules without antiimpact material and wearing out the surface or/and edge of LED modules might cause fatal problem. 8. It's highly recommended to use twisted cable or shielded wire in order to remove the noise from high frequency. 9. When user use and store LED module, please pack LED module with antistatic material. VS192F /10

VL500T2P1-01S LED DOT MATRIX MODULE

VL500T2P1-01S LED DOT MATRIX MODULE VISSEM ELECTRONICS CO., LTD R&D DIVISION 262-14, Guseong-ro, Giheung-gu, Yongin-si, Gyeonggi-do, 446-915, KOREA TEL: +82-31-288-3427~9, 3420 FAX: +82-31-288-3490~1 HTTP://WWW.VISSEM.COM LED DOT MATRIX