IEEE / PES /TRANSFORMERS COMMITTEE. Standards Report

Transcription

1 IEEE / PES /TRANSFORMERS COMMITTEE Standards Report To: Members of IEEE Committee Revision 1: From: William H. Bartley, Standards Coordinator Executive Summary This report covers the Committee Standards activity for the 6-½ month period from March 15 th to September 30, In the last six months, no new Standards, one Revision and one Corrigenda were approved by Standards Board. In this same period, the Standards Board approved two PARs for a new standard; and one PAR for an Amendment. In this Report: I. REVCOM / Standards approved... pg 1 II. NESCOM / PARS approved... pg 2 III. Standards Board 2014 Meeting Schedule... pg 2-3 IV. Committee Ballot Status... pg 4 V. Transformer Committee active PARs... pg 4-6 VI. Transformer Stds Status database... pg 7-21 VII. Transformer Stds Org Chart... pg I. Standards approved since March 15, 2013 NEW Transformer Standards None Transformer REVISIONS approved,!! C Standard for Bar Coding for Distribution and Step-Voltage Regulators This will expire Aug 23, 2023 CORRIGENDA approved: C /Cor IEEE Std Test Procedure for Thermal Evaluation of Insulation Systems for Dry-Type Power & Dist, Including Open-Wound, Solid-Cast, and Resin-Encapsulated (Note: A Corrigenda does not affect Expiration. This standard expires Nov 9, 2019!) - Page 1 of 22-

2 II. PARs approved since March 15, 2013 PARs for New Standards and Revisions PC57.121a Guide for Acceptance and Maintenance of Less Flammable Hydrocarbon Insulating Liquid in : Amendment a (Note this is a PAR for an Amendment) PC Guide for Dielectric Frequency Response Test PC Guide for the Interpretation of Moisture Related Parameters in Dry, Gas Insulated and Liquid Immersed and Reactors PAR Modifications approved none PAR Extensions approved none III IEEE Standards Board Meeting Schedule A. DEADLINES for 2013 & 2014 STANDARDS BOARD Submissions: Standards Board Meeting Deadline December 2013 Monday, 21 st October 2013 March 2014 February 14, 2014 June 2014 May 2, 2014 August 2014 July 11, 2014 December 2014 October 20, 2014 B. RECENT STANDARDS BOARD Submissions (as of Sept 30, 2013) The following was approved on the October Agenda for Early Consideration PC Corrigenda 2 Std Requirements for Liquid Immersed Power - Corrigendum 2: Correction of A The following standards have been submitted to REVCOM, and are already on their December Agenda. PC57.96 Guide for Loading Dry-Type Distribution and Power PC Guide for Determination of Hottest-Spot Temperature in Dry-Type P638 - Standard for Qualification of Class 1E for Nuclear Pwr Gen Stations Fall 2013 Standards Report Page 2 of 22

3 III. c 2013 Standards Board Meeting Schedule Fall 2013 Standards Report Page 3 of 22

4 IV. Transformer Committee Ballot Status (as of Oct 13, 2013) SubCommittee/ Title Standard # Bushing Subcommittee C Requirements, Terminology, & Test Code for Bushings DC Applications / NOTE PAR extension request submitted Distribution SC Date Ballot Closed 5-Jul-2013 PC Standard for Pad-Mounted Equipment Enclosure Integrity 7 Sept 2013 PC Dry Type PC Standard for Pad-Mounted Equipment Enclosure Integrity for Coastal Environments Guide for Determination of Hottest-Spot Temperature in Dry-Type 7 Sept 2013 PC Standard Requirements for Dry-Type Dist & Power 15 Sept 2013 Ins Fluids SC PC Power IEEE P638 Guide for DGA in Ester Fluids Ballot Pool Invitation closed Sept 15, 2013 Standard for Qualification of Class 1E for Nuclear Pwr Gen Stations Ballot is complete & submitted to Revcom 17-Oct Aug-2013 PC Guide for Directly Connected to Generators 22-Aug-2013 UTNP PC Standard Requirements for Secondary Network Protectors 10-Jun-12 Current Status Comment Resolution Comment Resolution Comment Resolution Submitted to REVCOM Comment Resolution In Ballot Submitted to REVCOM Comment Resolution Comment Resolution V. Transformer Committee PAR Status (as of Oct 13, 2013) PAR # Description PAR first approved PAR Expires Dec 31 st P1276 Application Guide for Hi-Temp Insulation Materials in L.I. Power 6-Feb P Standard Requirements for Wind Turbine Generator 8-Jun P Standard Requirements for Liquid Immersed Phase-Shifting 8-Jun P Standard for Bushings for DC application 5-Dec PC Guide for the Interpretation of Gases Generated in Oil-Immersed 5-Feb PC Guide for Acceptance and Maintenance of Insulating Oil in Equipment 9-Nov PC Guide for Directly Connected to Generators 10-Sep PC Std Gen Requirements for L.I. Distribution, Power, and Regulating 16-Jun PC Standard for General Requirements for Dry-Type Distribution and Power 9-Dec PC Std for Ovrhd-Distribution <500 kva HV <34 500v; LV, 7970/13 800Y V 8-Jun PC Standard for Submersible, 3-ph, <3750 kva, HV < LV < 600 Volts 9-Nov PC Standard for Pad Mounted Equipment - Enclosure Integrity 30-Sep PC Standard for Pad Mounted Equipment - Enclosure Integrity for Coastal Environments 30-Sep PC Std for Pole-Mounted Eqpt - Enclosure Integrity - Corr 1: SCAB Corrosion Test / Mar Fall 2013 Standards Report Page 4 of 22

5 Committee PAR Status continued... PAR # Title PAR PC Std for Req s-pad-mounted, Compart'l Self Cooled, 3 ph Dist, <10 MVA 31-Mar PC Standard Requirements for Liquid-Immersed Distribution Substation 7-Dec PC Standard for the Electronic Reporting of Distribution Transformer Test Data 7-Dec PC Std for Pad-Mounted-Type, Self-Cooled, 1ph Dist ; <250 kva 25-Mar PC Standard Requirements for Distribution Transformer Tank Pressure Coordination 6-Feb PC Standard for Network, 3-ph, <2500 kva; Subway and Vault Types 30-Aug PC Standard Requirements for Secondary Network Protectors 17-Jun PC Guide for Dry-Type Transformer Through-Fault Current Duration 7-Dec PC Std Test Code for Liquid-Immersed Distribution, Power, and Regulating 16-Jun PC Guide for Loss Evaluation of Distribution and Power and Reactors 25-Mar PC57.121a Guide for Acceptance & Maint of Less Flammable Hydrocarbon Liquids - Amendment a 23-Aug PC Guide for Failure Investigation, Analysis, and Reporting for Pwr & Reactors 2-Feb PC57.13 Standard Requirements for Instrument 25-Mar PC C 1 Std Req for Instrument - Corrigendum 1: Figure 3 Correction 30-Sep PC Standard for Current with a Maximum ma Secondary Current of 250mA 30-Sep PC Trial-Use Guide for the Use of DGA Applied to Factory Temp Rise Tests 17-Jun PC Guide for Sound Level Abatement and Determination for L.I. Power > 500 kva 30-Sep PC Recommended Practice for Routine Impulse Test for Distribution 2-Feb PC Guide for Dissolved Gas Analysis in Transformer Load Tap Changers 16-Jun PC Guide for Eval and Reconditioning of Liquid Immersed Power 31-Mar PC Guide for Acceptance & Maintenance of Natural Ester Insulating Fluids in 6-Feb PC Guide for Paralleling Power 27-Mar PC Guide for Interpretation of Gases Generated in Ester Immersed 25-Mar PC Guide for Tank Rupture Mitigation of Liquid-Immersed Pwr and Reactors 16-Jun PC Guide for Conducting Functional Life Tests for DETC Contacts 7-Dec PC Guide for the Application of Tertiary & Stabilizing Windings in Powr 15-May PC Application Guide for in Photovoltaic Power Gen Systems 8-Jun PC Guide for the Electrical Measurement of Partial Discharges in High Voltage Bushings 6-Mar PC Guide for Dielectric Frequency Response Test 23-Aug PC Guide for Interpretation of Moisture Parameters in Dry, Gas Insulated and L.I. 23-Aug PC Std Performance Characteristics and Dimensions for Outdoor Apparatus Bushings 8-Dec PC Std Perf Characteristics & Dimensions for High Current Bushings w/ Cont. Current >5000 A 16-Jun PC57.32 Std Requirements & Test Procedures for Neutral Grounding Devices 7-Dec PC Guide for the Reclamation of Insulating Oil and Criteria for Its Use 10-Dec PC57.93 Guide for Installation and Maintenance of Liquid-Immersed Power 29-Mar PC57.94 Guide for Installation & Maintenance of Dry-Type Distribution & Power 9-Nov PAR Expires Fall 2013 Standards Report Page 5 of 22

6 IEEE/PES TRANSFORMERS COMMITTEE Status Report of Standards revised STANDARD SubCommittee BUSHING Chair Zhao P. (417) PC Standard Performance Characteristics and Dimensions for High Current Power Transformer Bushings Arpino C /16/2011 New Project C Standard General Requirements and Test Procedure for Power Apparatus Bushings Ellis K. P. (615) /8/2020 Formally Std. IEEE 21 Previous revision Errata issued March 2010 Reaffirmation approved 12/8/2010 C PC IEEE Standard Performance Characteristics and Dimensions for Outdoor Apparatus Bushings Zhang /8/2010 +PAR for Revision Formally Std. IEEE 24 Reaffirmed in PAR for Rev first approved Dec 2007 Mar '10: NesCom extended PAR, unitl December 2013 C P Standard Requirements, Terminology, and Test Code for Bushing for DC Applications - Corrigendum 1 Recksiedler /25/ /31/ PAR for Revision Published 6/6/2006 See Corrigenda 1, Published in 2006 New PAR for revision submitted 10/2007 Std merging with IEC std NesCom extended PAR, unitl December 2013 IEEE Work complete; still waiting for IEC. Extension Request submitted C IEEE Guide for Application of Power Apparatus Bushings Spitzer (817) T /31/2022 tommy.spitzer@oncorgroup.com New PAR requested and approved to 12/31/2010. NESCOM approved Extension till Dec 2012 Revision approved Dec 2012 Prepared by W. Bartley, Standards SC Chair Page 6 of 22

7 SubCommittee DIELECTRIC TESTS Chair Franchek M. A. PC (802) Guide for DFR Measurements Naderian A. 8/22/ /31/2017 C IEEE Guide for Partial Discharge Measurement in Liquid-Filled Power and Shunt Reactors C IEEE Guide for the Detection of Acoustic Emissions from Partial Discharges in Oil-Immersed Power C PC IEEE Recommended Practice for Routine Impulse Test for Distribution Poulin B. (450) Gross Crotty J.W /17/ C57.98 IEEE Guide for Transformer Impulse Tests Molden (845) A /31/2021 2/2/2011 New project std Revision approved June Reaffirmed in June '05 Reaffirmation approved by RevCom on 6/8/05. Dec '10: Nescom approved new PAR until Dec PAR to Revise IEEE Std C PAR extension requested and approved to 12/31/2009. Dec '10: PAR mod and extension approved by Nescom Prepared by W. Bartley, Standards SC Chair Page 7 of 22

8 SubCommittee DISTRIBUTION TRANSFORMERS Chair Shull S. PC PC C PC C PC C PC C C PC C C PC C PC C PC Guide for Distribution Transformer Loss Evaluation Standard Requirements for Distribution Transformer Tank Pressure Coordination Standard for Overhead Type Distribution, 500 kva and Smaller, High-Voltage Volts and Below; Low-Voltage, 7970/ Y Volts and Below Standard for Pad Mounted Equipment - Enclosure Integrity Standard for Pad Mounted Equipment - Enclosure Integrity for Coastal Environments (417) sshull@empiredistrict.com Pekarek T. J. (330) tjpekarek@firstenergycorp.com Gaytan C. (52) carlos.gaytan.cavazos@indsys.ge.com Traut A atraut@ieee.org Olen O. (262) rolen@cooperpower.com Olen O. (262) rolen@cooperpower.com /16/ Std for Pole-Mounted Eqpt - Enclosures for Coastal Olen O. Environment (262) /17/2020 rolen@cooperpower.com IEEE Standard for Pole Mounted Equipment - Enclosure Integrity Standard for Submersible Equipment - Enclosure Integrity Requirements for Pad-Mounted, Compartmental- Type, Self-Cooled, Three-Phase Distribution, 2500 kva and Smaller: High-Voltage, GrdY/ Volts and Below; Low Voltage, 480 Volts and Below IEEE Standard for Bar Coding for Distribution Standard Requirements for Liquid-Immersed Distribution Substation Olen O. (262) rolen@cooperpower.com Olen O. (262) rolen@cooperpower.com Shull S. (417) sshull@empiredistrict.com Matthews P (601) lmatthews@howard-ind.com Murphy J.R. (407) jerry.murphy@ieee.org /17/ /9/ /6/ /31/2016 6/8/ /31/2016 9/30/2010 9/30/2010 3/6/ /31/2017 3/31/2011 6/17/ /7/2011 PAR WITHDRAWN - Inactive WG Decision made at Las Vegas Meeting to discontinue this activity. New Project Standard with approved PAR for Revision PAR for Revision approved June 2012 Previously NEMA/ANSI C Published 9/30/2005 PAR for Revision approved by NESCOM Sept 2010 Previously NEMA/ANSI C Current standards Published 10/10/2005. PAR for Revision approved by NESCOM Sept 2010 new standard new standard approved June 2010 with PAR for Corrigenda Published 3/6/2003. New PAR approved 3/22/2007 Std Bd approved 6/17/2010 PAR for Corrigenda approved to correct SCAB corrosion test Published 3/7/2003. Reaffirmation approved Mar PAR for Revision Originally Std. 1447, Combined C & C Revised Standard approved Dec09 Mar '11: Nescom approved new PAR for Revision Formally P1265. PAR for Revision approved June 2010 std and approved PAR for Revision approved by SA Board on 9/27/2007 PAR for Revision approved Dec '11 Prepared by W. Bartley, Standards SC Chair Page 8 of 22

9 SubCommittee DISTRIBUTION TRANSFORMERS Chair Shull S. (417) C PC IEEE Standard for the Electronic Reporting of Transformer Test Data Crotty J.W /7/2011 with PAR for Revision Formally C57.132, IEEE Std D11d approved by SA Board on 3/30/2006. Published 7/21/2006. New PAR for Revision submitted Sept'11 approved Dec'11 C PC Standard for Pad-Mounted, Compartmental-Type, Self-Cooled, Single-Phase Distribution with Separable Insulated High- Voltage Connectors; High Voltage, GrdY/19920 Volts and Below, Low Voltage, 240/120 Volts; 167 kva and SmallerRequirements Ghafourian A. A. (731) /11/2019 3/24/ revision in progress This std replaces C & C Std published Nov PAR for Revision approved by Nescom Mar 2010 C57.15 IEEE Standard Requirements, Terminology, and Test Code for Step-Voltage Regulators Colopy C. A. (262) ccolopy@cooperpower.com /11/2019 Also known as Prepared by W. Bartley, Standards SC Chair Page 9 of 22

10 SubCommittee DRY TYPE TRANSFORMERS Chair Johnson, Jr. C. W. (276) C PC IEEE Standard General Requirements for Dry- Type Distribution and Power Including Those with Solid Cast and/or Resin Encapsulated Windings Holdway T /9/2009 with PAR Previous 1998 version was successfully revised and approved in Published 5/19/2006 PAR for Revision approved Dec 09. PAR extension approved March 2013; extending PAR to Dec 2015 Ballot Invitation opened Aug 16 C Ventilated Dry-Type Power, 501 kva and Large, Three-Phase, with High-Voltage 601 to Volts; Low-Voltage 208Y/120 to 4160 Volts - General Requirements Powell P. A. (202) papayne@ieee.org Previously NEMA document C , original publication by NEMA in 1981, Reaffirmed in This document was transferred to IEEE in Dec., by SA Sept 2008 C Standard Requirements for Sealed Dry-Type Power, 501 kva and Larger, Three- Phase, with High-Voltage 601 to Volts, Low-Voltage 208Y/120 to 4160 Volts Kennedy (716) S. P /31/2022 skennedy@niagaratransformer.com Previously ANSI C SA approved Dec 2012 C IEEE Standard Test Procedure for Thermal Evaluation of Insulation Systems for Ventilated Dry-Type Power and Distribution Wicks R. C. (804) roger.c.wicks@usa.dupont.com /31/2007 Withdrawn Dec C and C were merged together C IEEE Guide for Conducting a Transient Voltage Analysis of a Dry-Type Transformer Coil Kline A. D. (843) AKLINE1490@AOL.COM Active Reaffirmed Sept 2008 C PC IEEE Guide for Dry-Type Transformer Through- Fault Current Duration Powell P. A. (202) papayne@ieee.org /7/2011 Reaffirmation approved in 12/5/2006. PAR for Revision submitted Oct'11 and approved by Std Bd Dec'11 C IEEE Guide for Test Procedures for Thermal Evaluation of Insulation Systems for Solid Cast and Resin-Encapsulated Power and Distribution Wicks R. C. (804) roger.c.wicks@usa.dupont.com /9/2019 with Corrigenda IEEE Std C and IEEE Std C merged together in 2009 Corrigenda 1 approved by SA June 2013 C IEEE Standard Test Code for Dry-Type Distribution and Power Foster D. R. (815) dfoster@olsun.com /31/2021 C IEEE Recommended Practice for the Detection of Partial Discharge and the Measurement of Apparent Charge in Dry-Type Johnson, Jr. (276) C. W /9/2019 charles.w.johnson@us.abb.com Reaffirmed Dec09 C PC IEEE Guide for Determination of Hottest Spot Temperature in Dry Type Powell P. A. (202) papayne@ieee.org /7/2011 Reaffirmation approved 3/30/2006 PAR for Revision approved Dec'11 Submitted to Revcom On Dec'13 agenda Prepared by W. Bartley, Standards SC Chair Page 10 of 22

11 SubCommittee DRY TYPE TRANSFORMERS Chair Johnson, Jr. C. W. (276) C57.16 PC57.16 IEEE Standard Requirements, Terminology, and Test Code for Dry-Type Air- Core Series- Connected Reactors Dudley R. F. (416) Revision approved by Std Bd Sept 2011 C57.94 PC57.94 IEEE Recommended Practice for Installation, Application, Operation, and Maintenance of Dry- Type General Purpose Distribution and Power Stankes S (603) /9/2011 Reaffirmation approved by the SA Board on 12/6/2006 PAR for Revision approved Dec'11 C57.96 PC57.96 IEEE Guide for Loading Dry Type Distribution and Power Marek (804) R. P Richard.P.Marek@usa.dupont.com 12/9/ /31/ Active RevCom approved reaffirmation on 9/22/2004 Previous revision in PAR for Revision approved Dec 2009 Ballot completed and on Dec2013 Revcom agenda. IEEE 259 IEEE Standard Test Procedure for Evaluation of Systems of Insulation for Dry-Type Specialty and General-Purpose Stankes S (603) /25/2020 9/22/04 RevCom approved reaffirmation Reaffirmed March 2010 SubCommittee HVDC CON TX & SMRs Chair Sharp M mikes@ca.trenchgroup.com C IEEE General Requirements and Test Code for Oil Immersed HVDC Converter Dudley R. F. (416) richardd@ca.trenchgroup.com 2007 Trial use std published 6/6/2000; upgraded to full use 3/2002 by SA Board 9/27/2007 IEEE 1277 IEEE General Requirements and Test Code for Dry- Type and Oil-Immersed Smoothing Reactors for DC Power Transmission Dudley R. F. (416) richardd@ca.trenchgroup.com /31/2020. Ballot approved March 2010 Prepared by W. Bartley, Standards SC Chair Page 11 of 22

12 SubCommittee INSTRUMENT TRANSFORMERS Chair McTaggart R. (416) PC Standard for Instrument Transformer with max output of 250ma Alton 9/30/2010 New Project New project approved by NESCOM Sept 2010 Standard Requirements for Station Service VTs Wallace New Project PC PAR application is on Dec13 SB Agenda C57.13 PC57.13 IEEE Standard Requirements for Instrument McTaggart R. (416) /30/ Active PAR for Corrigenda PAR to Revise IEEE Std C submitted to NESCOM PAR for Corrigenda to Correct Fig 3 approved Sept 2010 C Conformance Test Procedure for Instrument Smith J. E. (601) jes1@ieee.org /17/2020 PAR to Revise Std C ; harmonize with C D4 approved by RevCom on 6/8/2005; Published 9/29/2005. Reaffirmed 6/17/2010 C PC Standard of Performance and Test Requirements for Instrument of a Nominal System Voltage of 115 kv and Above Riffon P. (514) x3424 riffon.pierre@hydro.qc.ca /11/2019 Reference Std Previously C was a trial use Upgraded to Full Use 3/30/2006 C Standard for High Accuracy Instrument Smith J. E. (601) /17/2020 jes1@ieee.org Document published in 12/9/2005 Reaffiremed 2010 Prepared by W. Bartley, Standards SC Chair Page 12 of 22

13 SubCommittee INSULATING FLUIDS Chair McNelly S.J. PC PC C PC C PC IEEE Trial-Use Guide for the Use of Dissolved Gas Analysis During Factory Temeprature Rise Tests for the Evaluation of Oil-Immersed and Reactors (612) Thompson J. A /16/2010 DGA Guide for Esters filled Boman (785) P.E. 3/24/2010 IEEE Guide for the Interpretation of Gases Generated in Oil-Immersed IEEE Guide for Acceptance and Maintenance of Insulating Oil in Equipment C IEEE Guide for Acceptance of Silicone Insulating Fluid and Its Maintenance in C IEEE Guide for Acceptance and Maintenance of Less-Flammable Hydrocarbon Fluid in C PC Guide for Dissolved Gas Analysis in Transformer Load Tap Changers C Guide for Interpretation of Gasses Generated in Silicone-Immersed C PC IEEE 637 PC Ladroga R. K Rasor B. Boman P.E. (785) Sundin /19/ /31/2019 Wallach (980) D.J /8/2020 Murphy J.R. (407) /16/2021 Guide for Acceptance and Maintenance of Natural McShane C. P. Ester Fluids in IEEE Guide for the Reclamation of Insulating Oil and Criteria for Its Use Thompson J. A /9/ /9/ /7/2016 6/16/2011 2/6/ /31/ /10/2008 New Project New Project Std under development currently under ballot resolution. PAR extension requested and approved to 12/31/2007. New PAR approved June 2010 New Project PAR approved by NESCOM March 2010 Ballot Invitation Opened Aug 15, 2013 Active + New PAR for Revision PAR to Revise IEEE Std C Original PAR and document withdrawn in Dec New PAR approved in June, New PAR approved Jan 2010 Standard PAR for Revision approved Dec'11 Was to be administratively withdrawn in Dec., 2004 Reaffirmation ballot pool invitation initiated in October, Reaffirmed Dec 2009 PC was approved as a new standard by IEEE SA Dec 8, 2010 PAR for revision approved June 2011 Reaff approved 16 June 11. Active with active PAR for Revision New Standard approved May Reaffirmed Reaffirmation approved by SA Board 9/27/2007 PAR for Revision approved Dec 2008 PAR extension approved June 2012, until Dec 2014 Prepared by W. Bartley, Standards SC Chair Page 13 of 22

14 SubCommittee INSULATION LIFE Chair Forsyth B. I. PC PC Guide for the Definition of Thermal Duplicate Liquid-Immersed Distribution, Power, and Regulating Guide for Interpretation of Moisture in C IEEE Standard Test Procedure for Thermal Evaluation of Liquid-Immersed Distribution and Power C IEEE Recommended Practice for Performing Temperature Rise Tests on Oil Immersed Power at Loads Beyond Nameplate Ratings C PC Design, Testing and App of Liquid-Immersed with High-Temp Insulation C57.91 IEEE Guide for Loading Mineral-Oil-Immersed IEEE 1276 P1276 IEEE 1538 IEEE Guide for the Application of High- Temperature Insulation Materials in Liquid- Immersed Power IEEE Guide for Determination of Maximum Winding Temperature Rise in Liquid Filled Transformer Beaster B. L. (601) Prevost T. A Wicks (804) R. C /31/2021 Tuli S. C PAR WITHDRAWN Dec 2004 Previously P1524 Modified PAR to expire in 2004 PAR administratively withdrawn in December, /23/ /31/2017 Marek (804) R. P /19/ /31/2013 Duckett D. A. (407) Franchek M. A. (802) Forsyth B. I /31/ /31/2021 2/6/ /31/2016 New Project Standard Requested PAR for revision on 10/18/ st Ballot 2010; 1st Recirc Sept 2011; 2nd Recirc closed 20 Oct'2011 APPROVED Dec 2011 Previously IEEE 838. Published 3/12/2002. Reaffirmed Mar 2008 New Standard PAR for new standard approved March 2009 Standard Bd approved Aug 30, 2012 Combined from C & C & C with active PAR for Revision Upgrade from trial use to full use on 3/30/2000 Reaffirmation approved by SA Board in 3/30/2006 PAR for Revision submitted Oct'11 and approved by Std Bd Feb 2012 Original approval in Reaffirmed in Reaffirmed again in Dec 2011 Prepared by W. Bartley, Standards SC Chair Page 14 of 22

15 SubCommittee PERFORMANCE CHARACTERISTICS Chair TeNyenhuis E.G. P PC PC PC Standard Requirements for Wind Turbine Generator Guide for Short-Circuit Testing of Distribution and Power Guide for the Application of Tertiary and Stabilizing Windings in Power Guide for Application in Distributed Photovoltaic (DPV) in Power Generation Systems C IEEE Guide for Application of Transformer Connections in Three-Phase Distribution Systems C IEEE Guide for Liquid-Immersed Through-Fault-Current Duration C IEEE Recommended Practice for Establishing Transformer Capability When Supplying Nonsinusoidal Load Currents C PC IEEE Loss Evaluation Guide for Power and Reactors (519) Buckmaster D.E Fortin M Betancourt E. (52-80) Shertukde H.M. (860) Patel B. K. (205) Marek (804) R. P Traut A C IEEE Guide for Transformer Loss Measurement TeNyenhuis (519) E.G /17/2020 C PC C PC IEEE Guide for Sound Level Abatement and Determination for Liquid- Immersed Power and Shunt Reactors Rated Over 500 kva A Guide To Describe The Occurrence And Mitigation Of Switching Transients Induced By Transformer-Breaker Interaction Antosz S. (412) santosz@comcast.net Degeneff R. C. (518) degenr@rpi.edu /31/2020 6/8/ /31/2016 5/15/ /31/2016 6/8/ /31/2016 3/24/2010 9/30/2010 PAR PAR approved June 2012 This is an IEC Joint development PAR WITHDRAWN This PAR was withdrawn by consensus of PCSC. Proposed contents are reportedly addressed in C PAR PAR Was to be administratively withdrawn in Dec., Request extension to Reaffirmation ballot pool invitation initiated in October, Reaffirmed 2008 Reaffirmation ballot pool invitation initiated in October, Reaffirmed Mar 2008 PAR approved 11/18/2004. by SA Mar revision in progress Reaffirmation approved by RevCom 6/8/2006. PAR for Revision submitted 1/21/2010 to merge C & C std Ref Std. IEEE 1098 Revision approved June Active PAR for Revision Reaffirmation approved by RevCom on 9/21/2005 PAR for Revision approved by NESCOM Sept 2010 PC was approved as a new standard on December 8, 2010 Prepared by W. Bartley, Standards SC Chair Page 15 of 22

16 SubCommittee PERFORMANCE CHARACTERISTICS Chair TeNyenhuis E.G. (519) c Guide for the Application and Interpretation of Frequency Response Analysis for Oil Immersed Sweetser C.L. (781) /24/ /31/2012 APPROVED C IEEE Standard Practices and Requirements for Semiconductor Power Rectifier Kennedy (716) S. P /30/2019 Replaced the C for pool cathode mercury arc rectifiers. Amendment 1: Technical and Editorial Corrections was approved 3/27/08 Reaffirmed March 2009 C57.21 IEEE Standard Requirements, Terminology, and Test Code for Shunt Reactors Rated Over 500 kva 1990 Reaffirmation approved on 6/23/2004. Revised Std approved Mar 2008 IEEE 32 PC57.32 IEEE Standard Requirements, Terminology, and Testing Procedures for Neutral Grounding Devices Kennedy (716) S. P /7/ Active PAR to revise std Dec Sponsor changed from PES/SPD to PES/TR; PAR Modified and extended to Dec 2011; PAR stalled Oct'11, without a ballot. PAR withdrawn & New PAR submitted Oct'11, approved by Stds Bd Dec '11 Prepared by W. Bartley, Standards SC Chair Page 16 of 22

17 SubCommittee POWER TRANSFORMERS Chair Watson J.D. P PC PC PC C PC C PC C PC C C PC Standard Requirements for Phase Shifting joe_watson@ieee.org Ahuja R. K. (408) raj.ahuja@waukeshaelectric.spx.com 6/8/ /31/2016 Guide for Paralleling Power Jauch E.T. 3/27/2008 (727) jauch@ieee.org Guide to Tank Rupture Mitigation Zhao (417) P. 6/16/2011 peter.zhao@hydroone.com Guide for Conducting Functional Life Tests for Deenergized Tap-changer Contacts IEEE Guide for Directly Connected to Generators IEEE Guide for Reporting Failure Data for Power and Shunt Reactors on Electric Utility Power Systems Standard Requirements for Liquid-Immersed Power IEEE Guide for Failure Investigation, Documentation, and Analysis for Power and Shunt Reactors C IEEE Standard Requirements for Load Tap Changers C PC IEEE Guide for the Application, Specification and Testing of Phase- Shifting Hopkinson P. J. (704) phopkinson@ieee.org Hoffman (973) G grhoffman@advpowertech.com Binder, Jr. W. B. (724) wbbinder@aol.com 1986 Hoffman (973) G /30/2020 grhoffman@advpowertech.com Binder, Jr. W. B. (724) wbbinder@aol.com Sim H. J. (919) jin.sim@ieee.org /31/ /16/ /7/1011 9/10/2011 2/1/2011 6/14/ /31/2017 2/1/2011 PAR PAR approved June 2012 This is an IEC Joint development New Project PAR approved Mar 2008 PAR Extension granted May 2012, until Dec2014 New Project New Project PAR for New standard approved Dec'11 Reaffirmation approved in Dec Reaffirmation Ballot Closed with many Negatives PAR for Revision submitted July 2011 Active Previously IEEE , original approval date 6/19/1986. Oct 2010 decision to merge with C This standard is still Active because of PAR for revison of C This will be withdrawn when Revision of C is approved. standard with Corrigenda Formally NEMA/ANSI document. Corrigenda 1 approved December 2012 PAR for Corrigenda 2 approved June 2013 Oct'10: decision to merge with C Feb'11: NESCOM approved new PAR to merge 117 and 125. Standard PAR Modified Dec 09 and extended to Dec Dec '10: Nescom & Revcom extend untul Dec st Ballot closed May'11; 1st Recirc closed 21 Oct; Std was approved Mar 2012 for IEEE/IEC Dual Logo Dec IEC Ed. 1 Prepared by W. Bartley, Standards SC Chair Page 17 of 22

18 SubCommittee POWER TRANSFORMERS Chair Watson J.D. C PC Evaluation and Reconditioning of Liquid Immersed Power James R.I. (504) C Guide for Application for Monitoring Equipment to Chu D. Liquid-Immersed and Components (212) /31/2023 C Standard for Control Cabinets for Power Watson J.D /10/2021 C Guide for the Transportation of Large Power Anderson G. W. and Reactors (402) /31/2022 C57.17 Standard Requirements for Arc Furnace Ganser R. (330) /31/2022 C57.93 PC57.93 IEEE 638 P638 IEEE Guide for Installation of Liquid-Immersed Power IEEE Standard for Qualification of Class 1E for Nuclear Power Generating Stations Lau M. Y. (604) Swinderman (724) C /31/ /31/2105 3/29/ /31/2016 6/7/ /31/2013 D18 approved by RevCom 11/16/2006 Mar '11: Nescom approved new PAR until Dec Standard by Std Bd Sept 2011 Originally IEEEStd 17 Standard - with approved PAR for Revision Rev of ASA C , IEEE Std C , & C PAR to Revise IEEE Std C by RevCom 12/2007 PAR for Revision was approved March Active - with errata dated 4/7/1999 Reaffirmation approved by SA Board 3/30/2006. New PAR for revision approved 6/7/2007. PAR extended until Dec PAR extended until Dec Standard ballot complete and on Dec13 SB Agenda. Prepared by W. Bartley, Standards SC Chair Page 18 of 22

19 SubCommittee STANDARDS Chair Bartley W. H. (860) C PC IEEE Standard for General Requirements For Liquid-Immersed Distribution, Power, and Regulating Snyder S. L. (731) /17/2020 6/16/ rev approved by SA Board in June, Published 9/10/2010. PAR for Continuous Revision approved June 2011 C IEEE Standard Terminal Markings and Connections for Distribution and Power Shull S. (417) /31/2021 Published 3/16/2001. Reaff approved by RevCom 3/30/2006. New Revision approved by Std Board Dec 2011 C IEEE Standard Terminology for Power and Distribution Chiu B. (626) /30/2020 std Amendment PAR approved to add thermally upgraded definition Revision approved Sept 2010 C PC IEEE Standard Test Code for Liquid-Immersed Distribution, Power, and Regulating Antosz S. (412) /17/2020 6/16/2011 Published Oct 2010 PAR for Continuous Revision approved June 2011 C Guide for Metric Conversion of Transformer Standards Balma P.M. (973) /25/2020 Published 10/22/2004 Reaffirmed March 2010 IEEE C IEEE Guide for Diagnostic Field Testing of Power Apparatus - Part 1: Oil Filled Power, Regulators, and Reactors Verner J. A javerner@pepco.com /31/2023 Originally IEEE 62. Reaff was successful.in New WG formed to revise document on a continuous basis based on TF recommendation. Revision changed to C57 series, Prepared by W. Bartley, Standards SC Chair Page 19 of 22

20 SubCommittee UNDERGROUND TR & NW PROTECT Chair Niemann C. G. (847) C IEEE Standard for Underground Type, Self-Cooled, Single-Phase Distribution with Separable Insulated High-Voltage Connectors; High Voltage 25kV and Below; Low Voltage 600V and Below Traut A /19/2019 Published 4/20/2009 C PC Requirements for - Underground- Type, Three Phase Distribution : High Voltage ( GrdY/ V and Below) and Low Voltage (480V and Below, 2500 kva and Smaller Termini (610) G /17/2019 giuseppe.termini@peco-energy.com 11/9/2011 standard New PAR for Revision approved Nov '11 C PC Standard for Requirements for Secondary Network - Subway and Vault Types (Liquid Immersed) Klaponski B. (204) brian.klaponski@carte.ca /31/2021 8/30/ /31/2016 Standard with approved PAR for Revision C C PC IEEE Standard Requirements for Secondary Network Protectors Wimmer W. G. (804) bill_wimmer@dom.com /17/2010 PC /D2.1 approved by RevCom in December Published 6/07/2006 PAR for Revision approved June 2010 C Requirements for Ventilated Dry-Type Network 2500 kva and Below, Three-Phase with High Voltage Voltas and Below, Low Voltage 216Y/125 and 480Y/125 Volts Robinson A. L. (361) alrobinson@aep.com /31/2000 Standard WITHDRAWN in 2001 Existing standard withdrawn by IEEE on 1/15/2001. No longer endorsed by IEEE. Prepared by W. Bartley, Standards SC Chair Page 20 of 22

21 IEEE/PES Committee Chair: Bill Chiu Vice Chair: Don Platts Secretary: Stephen Antosz Treas: Greg Anderson Past Chair: J. Ed Smith Std. Coordinator: Bill Bartley Revised 10/20/2013 BUSHING Peter Zhao DISTRIBUTION Steve Shull DRY TYPE Chuck W. Johnson HVDC Converter Xfmrs & Smoothing Reactors Michael Sharp INSTRUMENT Ross McTaggart UG & NW Protector C. G. Niemann POWER Joe Watson Gen. Req. of Bushings Rev of C OH Dist. Xfmrs C General Req. C Req. & Test Code for HVDC Con. Xfmr C Req for Inst. Xfmrs C57.13 UG Self-Cool 1-ph C Req. for Liq. Imm. Power Xfmrs C Performance Characteristics C Req. & Testing of DC Bushings C Bushing App. Guide C Perf Characteristics for GSU Bushings PC Req. for 3ph Pad Mount C Dist. Sub. Xfmrs C Pad-Mount 1ph Self- Cool <2500kVA C Eqp Encl. Integrity C , 12.29, 12.30, 12.31, & Step Volt. Regulator C57.15 Elec Rpt of Test Data IEEE 1388/C Dry Type Air-Core Reactors C57.16 Req.for Vent. <=500KVA C Req. for Sealed >500kVA PC Transient Analysis C Test Code C Dry-Type Hottest Spot C Req. & Test Code for HVDC Smoothing Reactors IEEE 1277 Req.for Vent. >500KVA PC Thermal Eval. for Dry-Type C & Dry-Type Through Fault Current Duration C Dry Type Op & Maint. Guide C57.94 Test Proc. For Inst. Xfmrs C Test Req. for >= 115kV PC Req. for Elect. Rev. Metering C Req. for ma CT C TF for SSVTs PC D. Wallace Std Requirements Phase Shifters P UG 3ph Dist Xfmr < 2500KVA C Std. Req. for Sec. Network Xfmrs C Std. Req. for Sec. Network Protectors C Vent Dry-Type Network Xfmrs <=2500KVA C Transportation Guide PC Installation & Maint Guide C57.93 Arc Furnace Xfmr C57.17 Directly Connected GSU C IEEE 638 Std for Class IE Tx at Nuc Gen Stations Requirements for LTC C Phase-Shift Xfmrs C Eval & Reconditioning C Tank Pressure Coordination C Bar Coding C Guide for Paralleling C Failure Investigations C Functional Life Tests for DETC C Tank Rupture Mitigation C P. Zhao Guide for Monitoring C Std for Control Cabinet C Revised by W. Bartley Page 21 of 22

22 IEEE/PES Committee Chair: Bill Chiu Vice Chair: Don Platts Secretary: Stephen Antosz Treas: Greg Anderson Past Chair: J. Ed Smith Std. Coordinator: Bill Bartley Revised 10/20/2013 DIELECTRIC TEST Mike Franchek Performance Characteristics Ed tenyenhuis Insulating Fluids Sue McNelly Insulation Life Bruce Forsyth Standards Wm. Bartley Meetings Greg Anderson Impulse Test Guide for Dist Tx C J Crotty PCS Rev. to Gen Req S. Snyder PCS Rev to Test Code DGA Guide C R. Ladroga Loading Guide C57.91 Don Duckett Cont Rev of C S. Snyder Website Development S. McNelly Rev of Transient Voltage Test P. Riffon/P. Heinzig Rev of Low Freq. Tests B. Poulin PD Measurement On Bushings & Inst Tx B. Poulin Guide for Acoustic PD C D. Gross WG on Dielectric Test Table P. Hopkinson WG- External Dielectric Test Clearance Eric Davis Semicon Rectifier Xfmrs C S. Kennedy App. Guide for Xfmr Connections C Non-Sinusoidal Load Current C Short Circuit Testing PC Neutral Grounding Devices IEEE32/ PC57.32 Sound Level Abatement C Req. & Test Code for Shunt Reactors >500kVA C57.21 Through-Fault Current Duration C Xfmr Loss Measurement C Mitigation of Switching Transients CB/Xfmr Interaction C Guide to Freq Response Analysis C Tertiary & Stabilizing Windings PC Mineral Oil C Silicone Oil C Less Fammmable H-C Fluid C D. Sundin DGA During Thermal Test C J. Thompson DGA in LTC C D. Wallach App Guide for Ester Fluids -C P. McShane DGA in Silicone C J. Murphy Thermal Eval Test C R. Wickes Temp Rise Test Above NP Rating C TF Investigate Use of Furan Testing S. Xu Max. Wdg Temp Rise IEEE 1538 App. Of High Temp Insulation IEEE 1276 M. Franchek WG Std Req. Hi Temp Insulation C R. Marek Cont. Rev of C S. Antosz Terminal Markings & Connections S. Schull C Terminology C B. Chiu IEEE /IEC Cross Reference TF V. Mehrotra Diagnostic Field Testing J. Verner IEEE C /(62) TF - Temp Rise Test - C , Clause 11 P. Powell Educational Development T. Prevost Metric Conversion C P. Balma Committee History P. Balma TF Fluid terminology consistency P. McShane WG- Guide for DFR testing PC A. Naderian Sound Level Measurement PC DPV Grid PC TF for Particle Count M. Scarborough TF Moisture in Insulation B. Rasor TF Winding Temp Indicators P. McClure Windfarm P DPV Grid PC DGA in Ester Fluids PC P. Boman Oil Reclamation IEEE 637 J. Thompson Moisture in Insulation PC T. Prevost Revised by W. Bartley Page 22 of 22