VKI3. Inductive strip edge position control for rolling mills. single-side robust maintenance-free

Size: px

Start display at page:

Download "VKI3. Inductive strip edge position control for rolling mills. single-side robust maintenance-free"

Elaine Cox
5 years ago
Views:

1 VKI3 Inductive strip edge position control for rolling mills single-side robust maintenance-free

VKI3 Strip edge position control of metal str Operating principle: In advanced rolling mills, knowledge of the precise width and the position of the strip edge is crucial for precise mill control.

In extreme cases, this can mean stopping the rolling process and correcting the coil on a rewinding line.

In the past, the strip position was measured using an optical measuring system.

meet today s requirements in terms of operational safety and availability.

by non-contacting the material being processed. The single-side measuring unit is accommodated in a position below the measured strip and for mechanical protection also below a plastic wearing plate.

2 VKI3 Strip edge position control of metal str Operating principle: In advanced rolling mills, knowledge of the precise width and the position of the strip edge is crucial for precise mill control. In particular the wedge-shape of slit strip causes the strip position in the rolling mill to deviate more and more from one pass to another unless it is corrected. In extreme cases, this can mean stopping the rolling process and correcting the coil on a rewinding line. Combined with flatness measurement rolls, the measurement of strip position and absolute strip edge position helps to optimise strip flatness during the cold rolling process. In the past, the strip position was measured using an optical measuring system. However, in the harsh environment of a rolling mill where there is a high presence of rolling oil, atmospheric pollution and dirt, optical sensors require intensive maintenance and even then do not meet today s requirements in terms of operational safety and availability. EMG s VKI3 measuring unit uses an inductive measuring principle with a coil system which is designed to reliably detect the precise position of the edge of metal strip and foil in harsh environments by non-contacting the material being processed. The single-side measuring unit is accommodated in a position below the measured strip and for mechanical protection also below a plastic wearing plate. The plastic wearing plate is fixed to the carry-over-table. Data on the current strip edge position, strip centre position, and strip width is continuously provided over the signal interface. Digital signal interfaces are available for communication with the higher ranking automation equipment. Installation in direct proximity to a flatness measuring roll EMG VKI3 measuring unit in a constricted position EMG Automation GmbH specialises in the automation of continuous production processes in the metal, paper and plastics industries as well as in the foil and tyre industries. The company, which was established in 1946, is a leading provider of electro hydraulic control systems. Furthermore, EMG provides quality assurance systems for the manufacturing industry. Based on the combination of more than 70 years of experience, the quality of our products and complete solutions as well as our advisory skills, our customer, by his trust, makes us the market leader. In close co-operation with our customers, research facilities and universities we are permanently searching for innovative solutions to promote our new and further developments and therefore to design and form the market as innovation leader actively. Inductive edge sensor

3 ip and foil single-side Measuring principle: The inductive measuring unit detects the absolute strip edge position of any metallic material from one side and is based on the eddy current generated inside the strip. Measurement is largely independent of the material and of the flat strip pass line as material and height variations can be compensated in parts by using an integral reference coil. A stable aluminium housing protects the measuring electronics against splash-water and temporary submersion into fluids. The compact measuring beam has electromotor-driven adjusting slides on either side of the strip. Their position is constantly monitored using a digital position encoder. The slides guide the inductive edge sensors at right angles to the strip pass direction. The sensors transmit current information on the proportion of the sensor covered by the strip to an integral electronic unit while following their assigned strip edge using a rigid position control loop. Using the position values together with the extent of sensor coverage, the two strip edge positions, the strip position and the strip width can be deduced. A microprocessor-based electronic unit feeds, evaluates and monitors the complete measuring unit and provides the data output. Measuring coils Reference coils Motor CAN-Bus Transducer Microprocessor operated electronics unit Internal VKI3 accommodation for strip width measurement

robust maintenance-free Performance data: Protection class: Sensor positioning speed: Voltage supply: Temperature range: IP 65 and IP 67 at a separate wearing plate 30 mm/s on each strip side 24 V

type) Measuring distance from strip running level: 1-20-40 mm (from sensor without wear plate) Dimensions: Signal interface: Minimum strip width: 140 x 270 x L mm (L depends on measuring range and

Edge sensor within the EMG VKI3 measuring unit Complete view of the EMG VKI3 measuring unit Customer s benefits: Maintenance-free High precision strip edge, strip centre and strip width measurement

4 robust maintenance-free Performance data: Protection class: Sensor positioning speed: Voltage supply: Temperature range: IP 65 and IP 67 at a separate wearing plate 30 mm/s on each strip side 24 V DC, 5 A 0-50 C and 0-80 C (with water-cooled sensor system) Measuring accuracy for strip centre position: +/- 1 mm (for flat strip; at +/- 10 mm heigth difference and constant material thickness and type) Measuring distance from strip running level: mm (from sensor without wear plate) Dimensions: Signal interface: Minimum strip width: 140 x 270 x L mm (L depends on measuring range and line width) Digital bus communication Profibus, Ethernet-Modbus TCP, Ethernet-Socket TCP 300 mm at detection of one strip edge 400 mm at detection of both strip edges (lower strip widths on request) Edge sensor within the EMG VKI3 measuring unit Complete view of the EMG VKI3 measuring unit Customer s benefits: Maintenance-free High precision strip edge, strip centre and strip width measurement Compact design to suit limited installation space Electronics integrated into the measuring unit with no other external components Various Fieldbus interfaces for control and communication with higher ranking PLC Integral sensor system, factory-adjusted (measuring and reference coils)

Technical features: Complete integration of electronics inside the

design to suit a large range of strip width variations Unipolar 24 VDC

possible Optional ECU control unit in parallel to the interface with the

5 Technical features: Complete integration of electronics inside the sensor measuring unit High functional and operational safety Basic design to suit a large range of strip width variations Unipolar 24 VDC supply Compensation of faulty measurements due to crossbow effects possible Optional ECU control unit in parallel to the interface with the automation equipment Separate wearing plate to protect the VKI3: EMG VKI3 measuring unit

Automation GmbH Industriestraße 1 57482 Wenden Germany Phone: +49 2762 612-0 Fax: +49 2762 612-384 automation@emg-automation.com www.

6 Automation GmbH Industriestraße Wenden Germany Phone: Fax: automation@emg-automation.com Group.moving ahead. EMG / A-V / EN / VKI3 / Item No.: / Revision 00 / / Printed in Germany / Subject to modification

EVK/EVM. Optical strip edge and centre guiding system. high-precision reliable easy to maintain

EVK/EVM. Optical strip edge and centre guiding system. high-precision reliable easy to maintain EVK/EVM Optical strip edge and centre guiding system high-precision reliable easy to maintain EVK/EVM Continuous strip edge / strip Operating principle: The EVK edge sensor positioning device and the EVM