WIRELESS DIMMER FOR HEATING

Transcription

1 TELECO AUTOMATI SRL - Via dell Artigianato, Colle Umberto (TV) ITALY TELEPHE: FAX: This document is the property of Teleco Automation Srl who reserves all reproduction and copying rights WIRELESS DIMMER FOR HEATING Wireless dimmer for resistive and infrared heaters. Possibility to dimming from 0% to 100%. Inputs for external wired push-button and wired PIR sensor. Automatic room s temperature control via external wired temperature probe. Compatible with all TV-Link transmitters. 2 Models available with extended range from 120Vac to 230Vac: TVHET868A04: up to 4000W - to control 1 Heater of 4000W - to control 2 Heater of 2000W each TVHET868A06: up to 6500W - to control 1 Heater of 6500W - to control 2 Heater of 3200W each 4.5cm Functions by: Wireless Transmitters : - - Dimming from 0% to 100% - OFF Push-Button : 19.5cm TVHET868A04 TVHET868A Dimming from 0% to 100% - OFF PIR Wired and Wireless : 20cm - at 100% TECHNICAL SPECIFICATIS Model/Code Power supply Maximum total load Dimensions (mm) TVHET868A04 120/230 Vac~ 4000W 195 x 200 x 75 50/60Hz TVHET868A06 120/230 Vac~ 6500W 195 x 200 x 75 50/60Hz dimmer Infrared and resistive heaters 1

2 Infrared and resistive heaters Wiring Diagram INPUT STATUS - LED when ACTIVE LED ERROR - Fix : overload - Blinking : overtemperature RADIO TRANSMISSI - When blinking a radio trasmission is received Temperature trimmer (see par.8) DANGER Hi-Voltage Safety Lo-Voltage Zone DIP-Switch (see par.1) OUTPUT Level Temp probe Optional P.S. Power supply E SINGLE OUTPUT LOAD 6500W max Safety Low Voltage Input T1 T2 T3 COM P1 - Memorize Tx. P2 - Delete Tx. P3 - Function (see par.7) - When not used, close cable glands with their caps. - Hi-Voltage board, risk of electric shock. - Never touch the board outside the safety zone. 2

3 1 - DIP Switch Function DIP SWITCH PIR time is 30 minutes PIR time is 15 minutes - Use DIP1 to set the PIR time from 15min. to 30min. This function is active only when DIP.2 is enabled. - Use DIP2 to able and disable the PIR commands. Both wireless and wired PIR will be excluded. - Use DIP3 to select Resistive Heater or Infrared Heater When Infrared Heater is selected (DIP3 in position) and a command is received, the TVHET868A06 starts in soft mode, for extending the lifetime of the heater. PIR enabled Infrared Heater PIR disabled Resistive Heater Transmitters Memorization Memorisation of 7-channel transmitters 100% 75% 50% Min Dim+ Dim- OFF Function available only for 7 or 42ch. transmitter P1 one time it 1 - the push button P1 once it ; the buzzer will sound a continuous beep. 2 - During the beep sound press a push button of the 7-channel transmitter which has to be memorised; the memorization is indicated by the intermittent sound of the buzzer. All the push-buttons of the transmitter are automatically memorized with a preset configuration as in the above drawing. 3

4 To change the preset levels of the 7-channel transmitter ( CH1, CH2, CH3, CH4 ) CH1 CH2 CH3 CH5 CH6 Adjust CH4 CH7 5 sec. press press the button to be modified 1- one of the first four push button to be modified adjust new value 2- Adjust the new value with the two push buttons Ch5 and Ch6; press more than 5s 3- Hold the CH7 push button for 5 sec., after 5 sec. the load will turn on at the new value Memorization of 4 push-buttons transmitters with preset values The push buttons of the memorized transmitter will have the following functions: Preset Value: 2 times CH1: 100% CH2: 50% CH4: min CH4: Off 1- the push button P1 two times it the second one; the buzzer will make one beep and then sound continuously. 2 - During the beep sound press a push button of the transmitter which has to be memorised; the memorization is indicated by the intermittent sound of the buzzer. All the push-buttons of the transmitter are automatically memorized with a preset configuration as in the above drawing Memorization of one transmitter push-button with On/Off/Dim function With short impulses turn the load on and off; keeping it pressed to dim UP or DOWN the load. 3 times Function available for all type of transmitters 1- the push button P1 three times it the third one, the buzzer will make a beep each time and then sounds continuously. 2 - During the beep sound press the push button of the transmitter which has to be memorised; the memorization is indicated by the intermittent sound of the buzzer. 4

5 2.4 - Memorization of 3 push-buttons transmitters The push buttons of the memorized transmitter will have the following functions: CH5 dim UP, CH6 dim DOWN and CH7 turns /OFF the load. 4 times CH5: Dim + CH6: Dim - CH7: On/Off 1- the push button P1 four times it the fourth one, the buzzer will make a beep each time and then sounds continuously. 2 - During the beep sound press the push button of the transmitter which has to be memorised; the memorization is indicated by the intermittent sound of the buzzer. All the push-buttons of the transmitter are automatically memorized with a preset configuration as in the above drawing Memorization of one transmitter push-button with function The push-button memorised with On function turns on the last output level and does any time it is pressed. 5 times Function available for all type of transmitters 1- the push button P1 five times it the fifth one, the buzzer will make a beep each time and then sounds continuously. 2 - During the beep sound press the push button of the transmitter which has to be memorised; the memorization is indicated by the intermittent sound of the buzzer Memorization of one transmitter push-button with OFF function The push-button memorised with Off function turns off the load and does OFF any time it is pressed. 6 times Function available for all type of transmitters 1- the push button P1 six times it the sixth one, the buzzer will make a beep each time and then sounds continuously. 2 - During the beep sound press the push button of the transmitter which has to be memorised; the memorization is indicated by the intermittent sound of the buzzer. 5

6 2.7 - PIR Transmitters Memorization The wireless movement sensors (PIR) can be used to automatically activate the heater. 7 times 1- the push button P1 seven times it the seventh one, the buzzer will make a beep each time and then sounds continuously. 2 - During the beep sound activate the sensor; the memorization is ndicated by the intermittent sound of the buzzer. 3 - To copy a function of transmitter push-button to a new transmitter The push button P3 is locate inside the transmitter (see transmitter manual). The new transmitter will have the same functions of the transmitter used for its memorization. P3 Function available for all type of transmitters 1- the button P3. The enabled receiver sound continuously. 2- Within 5 sec. press a pushbutton of the already memorized transmitter of which the function has to be copied. The buzzer will interrupt the sound for 1 sec., and then carry on for 5 sec. 3- During the sound press the push-button of the new transmitter which has to be memorised; the memorization is indicated by the intermittent sound of the buzzer. P.S. When a 7 channel transmitter is copied, also its levels will be copied into the new one. 6

7 4.1 - To delete a transmitter Once 1- the push button P2 once it, the buzzer will sound slowly and intermittently. 2- During the sound press the push-button which has to be deleted; the deletion is indicated by the continuous sound of the buzzer To delete all transmitter 2 times 10s 1- the push button P2 two time it, the buzzer will make one beep and then sound quickly and intermittently. 2- Hold the push button for 10 sec., after this the buzzer will sound continuously by indicating that the whole memory has been cancelled To delete a transmitter from transmitter : P3 function P3 1- three times the button P3 placed inside of the transmitter. The buzzer will sound intermittently and slowly. 2- During the intermittent sound press the push button which is to be deleted; the deletion is indicated by the continuously sound of the buzzer. 5 - Memory Activation/Deactivation of the last value of the Load Memory function activated: when you control the load in /OFF mode, the load will turn-on with the same values it had before turning-off. Memory function deactivated: when you control the load in /OFF mode, the load will turn-on always at 100%. P.S.: The memory function is not possible when using the 7-ch. transmitter. 1- Push the push buttons P1+P3 and Hold - 1 beep : the function is activated. - 2 beep : the function is deactivated. 7

8 6- To set the minimum level for the Load This function allows to set the minimum level that can be reached by the load. the push buttons P1+P2 together and Hold : - 16 beep : the function is activated. - 3 beep : the function is deactivated. 1- Regulate the minim desired level 2- the push buttons P1 + P2 together it. The buzzer makes a beep. To reset the level to the default value, press again the push buttons P1 + P2 together it. The buzzer makes a beep. P.S.: Set a different value of the min. load level only with resistive loads (see DIP-Swith function on par. 1) 7 - Wired Input Function The receiver has three wired input (safety low votage): - T1: push-button input to /OFF and DIM the load For both the T1 and T2 push-button the function is: Short impulse (< 400mS) = /OFF Long impulse (> 400mS) = adjusting upgrade or grade. - T2: PIR Input to the load at 100% - T3: Not Used Temp Optional input with LED indicator T1 T2 T3 Push-Butt PIR input Not Used Safety Low Voltage 100m wire guaranteed 8

9 8 - Automatic Room Temperature Control It is possible to set the room temperature with the Automatic Temperature Control function. The control function works only when the temperature proble is connected to the unit. Control Disabled When activated, sounds one beep Temperature regulation S1 S2 S To activate the temperature control, turn the trimmer clockwise (see S2 position). At the activation the unit sounds one beep. When the control function is activated and the room temperature get higher than the confort temperature: - the dimmer will turn-off - the unit will exclude the next radio transmitter commands. - the unit cominicates that error with a beep. - To deactivate the temperature control, turn the trimmer to the left position S1 To bypass the temperature control keep press one of the first 4 push-button for about 7 seconds (only with 7-ch transmitters). 9 - Errors during the memorizing or deleting If the code hasn t been memorised it could be due to the following reasons: - the code already exists in memory. - the memory is full. - the indexing procedure has not been correctly started up. If the code hasn t been cancelled it could be due to the following reasons: - the code doesn t exist in memory. Memory full or empty If the memory of the receiver is full or empty the buzzer will sound three times either during the memorization phase or after the reset of the receiver. 9

10 10 - Warning The subject appliance must be installed only by qualified technical personnel in compliance with the standards. All connections must be rated for a single-phase power supply of 230V. For the disconnection from the power line, use an all-pole switch with contact with an opening of at least 3,5mm. Only suitable materials for the connections must be used to guarantee insulation that complies with current standards on the subject of electrical safety. The receiver only carries out /OFF commands and all safety devices required by the system must be prepared a part. Ground connection must be provided separately. In the connection to power line and to outputs follow the indications of line and neutral. Connections wire must have a section suitable to the applied load. In the view of a constant development of their products, the manufacturer reserves the right for changing technical data and features without prior notice. The appliance is not intended for use by people (including children) with reduced physical, sensorial or mental facilities, or with a lack of experience or knowledge, unless they are supervised by a person responsible for their safety or instruction concerning the use of the appliance. Children must be supervised to ensure that they do not play with the appliance. Must necessarily be fitted the cable glants provided or the cable glants with the same mechanical and safety characteristics. The power cable must have a nominal characteristic of 90 C temperature T. The main power supply must have connecting cables with a cross section suitable for the load applied to the relays. The connecting cables of the main power supply and of the loads must have adequate section and electrical isolation; their installation must comply with the standards on electrical systems. The following table shows (roughly) the typical values of maximum resistance for km and maximum tolerable current of a copper electrical wire, according to its section: Section (mm2) R (ohm/km) Max. current (A) If the power cable is damaged, it must be replaced by the manufacturer or by the technical assistance service or by a similarly qualified person, in order to avoid all the risks. Use the appliance only with loads in which the functioning isn t dangerous in the case that they remain permanently activated. The device s signal reception could be disturbed by several factors such as: - the presence of electrical frequency noise being transmitted by other appliances working in the same environment and on the same frequency. - appliances installed in metal containers or shielded from metal parts; only use containers made of plastic TECHNICAL SPECIFICATIS -Power supply 120/230 V 50/60Hz - Max Output Power 6500W at 230Vac~ 3400W at 120Vac - Reception frequency MHz - Operating temperature range -20 / +80 C -The maximum number of transmitters that can be memorized is

11 11