Certificate of Conformity

Transcription

1 pplicant: Moore Industries-International Inc Schoenborn Street North Hills C United States of merica Electrical pparatus: Current to Pressure Transmitter Models IPX2, IPX2-NG, IPH2 and IPT2 Type of Protection: IPX2, IPX2-NG, IPH2: Ex ia IPX2, IPH2, IPT2: Ex n Marking Code: NZEx X IPX2: Ex ia IIC T4@85 C /T5@70 C IP56 and Ex n IIC T6@55 C IPX2-NG: Ex ia IIC T4@85 C /T5@70 C IP66 IPH2: Ex ia IIC T4@85 C /T5@70 C and Ex n IIC T6@55 C IPT2: Ex n IIC T6@55 C Manufacturer: Manufacturing Location(s): Moore Industries-International Inc Schoenborn Street North Hills C United States of merica s above The EPEE certification database located at shows the validity of this Certificate. Certificate issued by: TestSafe ustralia 919 Londonderry Road, Londonderry NSW 2753 ustralia Phone: Fax: EPF019_18 Page 1 of 9

2 This certificate is granted subject to the conditions as set out in Standards ustralia/standards New Zealand Miscellaneous Publication MP87.1:2008. STNDRDS: The electrical apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following standards: S/NZS :2005 S/NZS :2006 S/NZS :2006 Electrical apparatus for explosive gas atmospheres Part 0: General requirements (including mendment 1) Explosive atmospheres Part 11: Equipment protection by Intrinsic safety i Electrical apparatus for explosive gas atmospheres Part 15: Construction, test and marking of type of protection, n electrical apparatus (including mendment 1) This Certificate does not indicate compliance with electrical safety and performance requirements other than those expressly included in the Standard(s) listed above. SSESSMENT & TEST REPORTS: The equipment listed has successfully met the assessment and test requirements as recorded in: Test Report No. and Issuing Body: TestSafe Report 30543, 33070, Quality ssessment Report No. and Issuing Body: GB/SIR/QR /02 File Reference: 2016/ ugust 2016 Signed for and on behalf of issuing body Date of Issue Quality & Certification Manager Position This certificate is not transferable and remains the property of the issuing body and must be returned in the event of it being revoked or not renewed. EPF019_18 Page 2 of 9

3 EQUIPMENT: Schedule The Current-to-Pressure (I/P) Transmitter converts a current signal to a pneumatic signal so that an electronicbased system such as a DCS, PLC, or PC can control a pneumatic actuator, valve, or damper drive. vailable models accept a wide range of current inputs (4 20 m, 4 12 m, and m) and provide a proportional pneumatic signal (3 15 psig, Bar, kpa, etc.). Housing Styles vary according to Model: IPX2: Field Mounted & robust aluminium body. IPH2: Field Mounted & compact lightweight aluminium body with polyester or aluminium terminal cover housing. IPT2: Compact 40 mm wide aluminium housing for mounting onto DIN-rail or pneumatic header rack. Requires optional housing for field mounting. The input terminal shall be connected via a barrier which consist of a series resistor. The installation manual is provided in document no & CONDITIONS OF CERTIFICTION: It is a condition of safe use that the following parameters shall be taken into account during installation: Input Parameters Ex ia Terminals +PS/-PS Ex n Terminals +PS/-PS Maximum Input Voltage U i 30 V 30 V Maximum Input Current I i (limited by series resistor in the barrier) Maximum Internal Capacitance C i Maximum Internal Inductance L i 110 m 110 m 5.7 F at 7.14 V 0 mh EPF019_18 Page 3 of 9

4 DOCUMENTS: Revision Level: Date: (yyyy-mm-dd) PC1, IPT [DIN] B IPT (Track rtworks) B PC2 IPT2-DIN D IPT-PC2 (Track rtworks) D PC3, IPT [DIN] B IPT-DIN PC3 (Track rtworks) B PC4, IPT2 [DIN] C IPT-DIN PC4 (Track rtworks) C PC1 IPH2-MII/IPX2-MII D IPH-MII/IPX-MII PC1 (Track rtworks) D PC3 IPH2-MII B IPH-MII PC3 (Track rtworks) B PC2 IPH2-MII/IPX2-MII C IPH-MII/IPX-MII PC2 (Track rtworks) C PC3 IPX2-MII B IPX-MII PC3 (Track rtworks) B PC1 IPX2-RO Option IPX2-RO PC1 (Track rtworks) B PC3 IPX2-RO Option IPX2-RO PC3 (Track rtworks) IPT2-DIN (Schematic) F IPX2/IPH2 (Schematic) D PC2 IPT2-DIN (PC ssembly) C PC4, IPT2 [DIN] (PC ssembly) C PC5, IPT2 DIN (PC ssembly) C PC1 IPH2-MII/IPX2-MII Not 4-20m/3-15PSiG D (SMT) (PC ssembly) PC1 IPH2-MII/IPX2-MII 4-20m/3-15PSiG C (SMT) (PC ssembly) PC1 IPH2-MII/IPX2-MII 4-20m/3-15PSiG (Thru-Hole) (PC ssembly) EPF019_18 Page 4 of 9

5 Revision Date: Level: (yyyy-mm-dd) PC1 IPH2-MII/IPX2-MII Not 4-20m/3-15PSiG (Thru-Hole) (PC ssembly) & PC1 IPH2 /IPX2 3-27/6-30PSiG (SMT & Thru Hole) (PC ssembly) PC1 IPH2 /IPX2 3-15PSiG (SMT & Thru-Hole) (PC ssembly) PC2 IPH2-MII (PC ssembly) PC3 IPH2-MII (PC ssembly) B PC2 IPX2-MII (PC ssembly) B PC3 IPX2-MII (PC ssembly) B IPX2-RO Option PC1 (Switch Selectable) (Fabrication) IPX2-RO Option PC1 (Switch Selectable) (PC ssembly) PC3 IPX2-RO Option (PC ssembly) B Electro-Valve ssembly, I/P (Mechanical H ssembly) Potted Core ssembly, I/P (Mechanical ssembly) B TG, ID, IPH2 TestSafe-NZEx: I.S., Type N B TG, Model No., IPX2 (Standard I/P Unit: ir) CS/FM/KEM:I.S./N.I/Exp-Prf. TestSafe- NZEx: I.S. & Type N (Mll-Type N) Universal ID Tag B TG, Model No., IPX2 Current-to-pressure X- mitter CS/FM/KEM: I.S. & Exp-Prf. TestSafe- NZEx:I.S.-NG Option: Natural/Sweet Gas (Universal ID Tag) ID Label IPT2 DIN Current-to-pressure X-mitter TestSafe-NZEx: Type N B EPF019_18 Page 5 of 9

6 Schedule of Variations Variations Permitted by Issue 1: dditional information added in the Certificate that were assessed in Test Report 30543: 1. dded IP rating in the Certificate. 2. dded equivalent internal capacitance for input voltage above 20 V. Condition of Certification Relating to Issue 1: It is a condition of safe use that the following parameters shall be taken into account during installation: Input Parameters Ex ia Terminals +PS/-PS Ex n Terminals +PS/-PS Maximum Input Voltage U i 30 V 30 V Maximum Input Current I i (limited by series resistor in the barrier) Maximum Internal Capacitance C i Maximum Internal Inductance L i 110 m 110 m 5.7 F at 7.14 V 0 F at Ui > 20 V 0 mh Variations Permitted by Issue 2: Only for IPX2 and IPX2-NG models: 1. Create a separate electronic module containing all electronic assemblies and the electromagnet. 2. This redesign includes only the re-packaging of the electronics and will keep the housing and pneumatic components untouched. 3. For extra protection against moisture, the electronic PCB assemblies contained in the electronic module will be encapsulated. 4. The change to the electronics (schematic) is to add additional filtering on the inputs. EPF019_18 Page 6 of 9

7 Condition of Certification Relating to Issue 2: The conditions of certification are unchanged from Issue 1 of the certificate. Drawings Relating to Issue 2: Revision Level: Date: (yyyy-mm-dd) IPX2 PC1 Thru PC4 (Repackage) (Schematic) IPX2 PC1 Repackage (PC Fabrication) IPX2 PC1 Repackage (PCB Layout) EPX2/IPX2 PC2 Repackage (PCB Layout) PC2 EPX2/IPX2 (PC Fabrication) PC Top, IPX2 Current to Pressure Transmitter (PC ssembly) PC1, IPX2 Current to Pressure Transmitter (PC ssembly) PC1 (Zero Based), IPX2 Current to Pressure Transmitter (PC ssembly) PC1 dded Parts, IPX2 Current to Pressure Transmitter (PC ssembly) PC2, IPX2 Current to Pressure Transmitter (PC ssembly) EPF019_18 Page 7 of 9

8 Variations Permitted by Issue 3: 1. Delete the epoxy coating on the external surface of enclosure. 2. Minor design change to the schedule drawings, PCB layout and safety components. 3. Update certificate equipment description. 4. Update the condition of Certification. Condition of Certification Relating to Issue 3: For Models IPX2, IPX2-NG and IPH2, when are used in Zone 0 environment, the apparatus shall be protected from impact. The following parameters shall be taken into account during installation: Ex ia Ex n Input Parameters Terminals +PS/-PS Terminals +PS/-PS Maximum Input Voltage U i 30 V 30 V Maximum Input Current I i (limited 110 m 110 m by series resistor in the barrier) Maximum Internal Capacitance C i 5.7 F at 7.14 V 0 F at Ui > 20 V Maximum Internal Inductance L i 0 mh Drawings Relating to Issue 3: Revision Level: Date: (yyyy-mm-dd) PC2, IPT2-DIN F IPT-PC2 (Track rtworks) F PC4, IPX2 [DIN] D PC4, IPX2 (Track rtworks) D PC3 IPH2-MII B IPT2-DIN (Schematic) G IPH2 PC1 - PC4 (Schematic) F PC2 IPT2-DIN D PC4, IPX2 / IPT2 [DIN] D PC2 IPH2-MII PC3 IPH2-MII EPF019_18 Page 8 of 9

9 Revision Level: Date: (yyyy-mm-dd) POTTED CORE SSEMBLY, I/P C NME PLTE, IPH2, TEST-SFE-NZEx: I.S., C TYPE N NME PLTE, IPX2 TESTSFE-NZEx: I.S. D ID LBEL, Model/Serial IPT2 [DIN] C Current-to-Pressure Transmitter IPX2 PC1 THRU PC4 (REPCKGE) C (Schematic) IPX2 PC1 REPCKGE E IPX2 PC1 REPCKGE (PCB Layout) E PC1, IPX2 CURRENT TO PRESSURE C TRNSMITTER PC1 (ZERO BSED), IPX2 CURRENT TO C PRESSURE TRNSMITTER Module, Mechanical ssembly, IPX2 C (BOM for PC4 PCB ssembly) D (BOM for IPX2 PC1 PCB ssembly) C - EPF019_18 Page 9 of 9