Known Errata/Corrigenda Items: ISO/FDIS 10423:2003 (E) (*Items starred are of higher priority for correction)
|
|
- Piers Ross
- 5 years ago
- Views:
Transcription
1 Known Errata/Corrigenda Items: ISO/FDIS 10423:2003 (E) (*Items starred are of higher priority for correction) *(1) Page 41, Figure 3 (b): Version 1, September 15, 2003 Material from ISO, API, Cameron Prepared by Eric Wehner, Cameron In first sentence, second line, change ER = 1/4 T to ER = 1 ¼ T Error appeared in 10423:2001 / 6A 18 th as well. (2) Page 121, Table 39 & Page 249, Table B.39: Change footnote superscript for R 20 and R25 in first column of Table 39 should from a to b. (e.g., R20 b, not R20 a ) Should be the same as for R 201 through R 215 in fourth column of table. (3) Page 127, Table 41: Change Diameter of bolt holes for 2 9 / 16 (in) 138,0 MPa flange from 36 to 35 mm. Should agree with tables 36, 37, 38, 43, and 45; 35mm was chosen as the standard hole diameter for 1 1 / 4 (in) bolts. *(4) Page 133, Table 44: Remove < 42,1 dimension from left side of flange and reinstate 31,8 dimension from right side, as in 10423:2001 / 6A 18 th. The < 42,1 dimension applies to Table 45 only. (5) Page 139, Table 47: Change Length of double-ended stud bolt for 4 1 / 16 (in) 34,5 MPa segmented flange from 130 to 135 mm. Should agree with corrected value of 135 mm used for 4 1 / 16 X 4 1 / 4 (in), which has identical flange dimensions. (6) Page 139, Table 47: Change Length of threaded stud bolt for 4 1 / 16 X 4 1 / 4 (in) 34,5 MPa segmented flange from 200 to 210 mm. Should agree with corrected value of 210 mm used for 4 1 / 16 (in), which has identical flange dimensions.
2 Page 2 of 5 *(7) Page 147, Table 49: Under column for Material Class DD, EE, FF, and HH, Exposed (Low strength), and in row for NACE MR0175, change 103,5 MPa flgs < 1 13 / 16 and 5 1 / 8 only to 103,5 MPa flgs 1 13 / 16 and 5 1 / 8 only. (Delete < symbol.) Error of adding < symbol occurred in adding 5 1 / 8 (in) 103,5 MPa flange. There are no flanges smaller than 1 13 / 16, so < 1 13 / 16 could be read to exclude all 103,5 MPa connections from using GR B7M and GR L7M bolting. (8) Page 151, Table 51: Change Width of ring, dimension A, for RX 25 from 8,73 to 8,74 mm. Should agree with corrected value of 8,74 mm for RX 20 (dimension A). Original inch dimension is 0,344 for both. (9) Page 151, Table 51: Change Width of groove, dimension F, for RX 20 and RX 25 from 8,73 to 8,74 mm. Should agree with corrected value of 8,74 mm for RX 20 (dimension A). Original inch dimension is 0,344 for all. (10) Page 152, Table 51: Change Width of groove, dimension F, for RX 63 from 26,99 to 27,00 mm. Should agree with corrected value of 27,00 mm for R 63 in Table 50. Original inch dimension is 1,063 for both. (11) Page 153, Table 52 & Page 275, Table B.52: Change drawing of groove at center top of page to show 1,5 X 45 at o.d. corner of groove only. (Delete 45 line shown on i.d. corner.) Not critical, illustration error only; 1,5 X 45 is not called for at i.d. of groove, and note (a) still applies, so drawing should be interpreted correctly regardless.
3 Page 3 of 5 (12) Page 157, Table 56: Change Full bore valve bore for 7 1 / 16 X 5 1 / 8 from 130,0 to 130,2 mm. Should agree with corrected value of 130,2 for 5 1 / 8 nominal size. (13) Page 208, Table 83: Change seventh line, SSV/USV actuator data, to bold face type. Should agree with other section headings in table. Error appeared in 10423:2001 / 6A 18 th as well. *(14) Page 208, Table 83: Change fifth line, PSL 2 class to PR 2 class. Error appeared in 10423:2001 / 6A 18 th as well. (15) Page 216, A.4.3: In second paragraph, change the reference from A.4.4 to A.4.5. Typo. (16) Page 233, Figure A.3: Change NACE MRφ175? to NACE MR0175? Should be a zero, not a diameter symbol. *(17) Page 261, Table B.44: Remove < 1,66 dimension from left side of flange and reinstate 1,25 dimension from right side, as in 10423:2001 / 6A 18 th. The < 1,66 dimension applies only to Table B.45. *(18) Page 335, subclause G.5.2.1: Change last sentence of G to add or G Sentence should then read as follows: Derated yield strength may be determined by one of the methods given in G or G This is an editorial error introduced in 10423:2001. API 6A 17 th Edition, G5.2 stated, Derated yield strength may be determined by one of the following methods. The phrase following methods was intended to include the remainder of Appendix G, both the
4 Page 4 of 5 (19) Page 349, Table J.1: elevated temperature testing methods of G5.2.1 (two given) and the use of reference sources described in G5.2.2 (two given). As worded, ISO implies that only the high-temperature material testing can be used, that the reference sources of G could not be used to obtain derating factors for materials. If that had been intended, there would be no reason to include subclause G in the standard. In first six lines below the column headings, remove to be, to change Equipment to be identified as to Equipment identified as (six places) Errors appeared in 10423:2001 / 6A 18 th as well. Reference is to existing equipment identification, not new identification added in remanufacture. (20) Page 349, Table J.1: In RL 1 column, add x to line 4: Equipment identified as originally manufactured as API Spec 14D, or ASME SPPE 1, and to line 7: Design status acceptable. Errors appeared in 10423:2001 / 6A 18 th as well. Equipment suitable for RL2 should be marked as suitable for RL 1. (21) Page 360, J.8.1: In last sentence, change orignal to original. Typo. (22) Page 362, Table K.1: In NOTE at bottom of table, change material class DD, EE, FF, HH, having a yield strength of to material class DD, EE, FF, or HH, having a minimum yield strength of Errors appeared in 10423:2001 / 6A 18 th as well. Without or the note implies that material must be suitable for all of material classes DD-HH. Also, the yield strength of 517 MPa is a minimum, not an exact value. *(23) Page 364, Figure K.1 & page 368, Figure K.2: Change length L to be shown as the depth of the internal bore J, not the length of the o.d. thread. Errors appeared in 10423:2001 / 6A 18 th as well.
5 Page 5 of 5 (24) Page 388, Figure L.8: Change diameter of groove below hex from 28,8 + 0,4 to 28,6 + 0,4. Typo - error appeared in 10423:2001 / 6A 18 th as well. The hex and the groove should be the same for VR plugs (13,8 through 69,0 MPa) and HPVR plugs (103,5 and 138,0 MPa). The correct conversion of inch is 28,6 mm. *(25) Page 389, Figure L.9: Change diameter of groove below hex from 1,25 + 0,015 to 1, ,015. Typo - error appeared in 10423:2001 / 6A 18 th as well. The hex and the groove should be the same for VR plugs (13,8 through 69,0 MPa) and HPVR plugs (103,5 and 138,0 MPa).
Kerkau Manufacturing. B16.5 Flange Book
Kerkau Manufacturing B16.5 Flange Book TABLE OF CONTENTS Revision 1 Title Page Table of Contents Tolerance Page Permissible Imperfections Dimensions of Flange Facings (all pressure rating classes) Dimensions
More informationWellhead equipment CATALOG
equipment CATALOG Wellhead & Christmas tree Fixed the drilled wellhead.connect wellhead casing ring,seal and control the annular of casing. suspend tubing,control wellhead pressure and adjust flow rate,also
More informationFlange Dimensions Class 125 Bronze Flange Dimensions Class 300 Bronze Flange Dimensions Class 150 Bronze Flange Dimensions
Dimensions Class Bronze Dimensions Meets Ib. A.S.M.E. Stard Class 00 Bronze Dimensions Meets ANSI STD B. Nominal Dim. A O.D. Dim. B Circle Dim. C Hole No. Holes Nominal Dim. A Diam. Dim. B Min. Dim. C
More informationCATALOG FOR PRESSURE CONTROL EQUIPMENT. Supplement 3 API CONNECTOR ACCESSORIES. Ring Gaskets, Flange Bolts and Nuts, Hammer Wrenches TRADEMARK WOODCO
CATALOG FOR PRESSURE CONTROL EQUIPMENT Supplement 3 API CONNECTOR ACCESSORIES Gaskets, Flange Bolts and Nuts, Hammer Wrenches This catalog supplement provides information to allow selection and accurate
More informationTable Of Contents Casing Head 02 Christmas Tree & Tubing Head Tubing Spool 04 Contact Us
Table Of Contents Casing Head 02 Christmas Tree & Tubing Head 03 Tubing Spool 04 Contact Us 05 1 www.sapwellsglobal.com Casing Head Specialized large-diameter pipe lowered into an open hole and cemented
More information5/16" Flange nut. Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc plated bolt w/ washers and nut. Anchor 3" sq. 7 Ga.
2 1/2" x 2 1/2" x 10 Ga. 6" 5" 4" Variable Slipbase (8" Sq. SYS.) 5/16 Corner Bolt W/ nut 5/16" Flange nut Stub Insert (8" Sq. SYS.) Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc
More informationCOLLET CLOSERS, FIXTURES AND COLLETS FOR ROTATING AND FIXED APPLICATIONS
COLLET CLOSERS, FIXTURES AND COLLETS FOR ROTATING AND FIXED APPLICATIONS ROYAL QUICK-GRIP MANUAL COLLET FIXTURES FOR 4TH AND 5TH AXIS APPLICATIONS q Unit is actuated via a hybrid mechanical/hydraulic mechanism.
More informationThread and End Connection
www.swagelok.com and End Connection I d e n t i f i c a t i o n G u i d e Contents Introduction and End Connection Terminology.. 4 General Terminology................... 5 Step-by-Step Identification
More informationBOLTS AND NUTS Square Bolts( Table 1 ) Hex Nuts ( Table 7 ) Heavy Hex Nuts (Table 7) Heavy Hex Structural Bolts ( Table 2 )
BOLTS AND NUTS 1493 An externally threaded fastener that must be assembled with a nut to perform its intended service is a bolt. (Example: heavy hex structural bolt.) An externally threaded fastener that
More informationMETRIC FASTENERS 1520 METRIC FASTENERS
1520 METRIC FASTENERS METRIC FASTENERS A number of American National Standards covering metric bolts, screws, nuts, and washers have been established in cooperation with the Department of Defense in such
More informationTechnical. Toolholding & Tapping. Product Warranty
Technical 4 Product Warranty Parlec Inc. warrants all tools, tooling systems, and tool presetters to be free of defects in manufacturing and materials for a period of one year from the date of shipment.
More informationThis specification describes the minimum requirements for piping systems for the following service:
201/11/2 1/9 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Underground Service Water Note: This specification does not apply to piping
More informationThis specification describes the minimum requirements for piping systems for the following service:
SPEC-3004 1/7 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Service Water Design Conditions Operating Conditions 10 PSIG @ 33 o F to
More informationStandard Specification for Carbon and Alloy Steel Nuts [Metric] 1
Designation: A 563M 04 METRIC Standard Specification for Carbon and Alloy Steel Nuts [Metric] 1 This standard is issued under the fixed designation A 563M; the number immediately following the designation
More informationThis specification describes the minimum requirements for service water piping systems (ie: cooling water, process water, etc.), located on surface.
SPEC-3500 1/9 1.0 PURPOSE This specification describes the minimum requirements for service water piping systems (ie: cooling water, process water, etc.), located on surface. Note: This specification does
More informationAUDAS. Tel: Fax: No.259 Baichi north Rd.Haiyan.Zhejiang.
Standard State SECTION A : SCREW THREAD Basic elements of screw thread design ANSI/ASME B1.7M Nomenclature.Definitions and letter symbols for screw thread ASME B1.1 Unified inch screw thread ( UN and UNF
More informationFluid Sealing Association
Fluid Sealing Association STANDARD FSA-MG-501-02 STANDARD TEST METHOD FOR INWARD BUCKLING OF SPIRAL-WOUND GASKETS 994 Old Eagle School Road, Suite 1019 Wayne, Pennsylvania 19087-1866 Phone: (610) 971-4850
More informationPIPING NOMENCLATURE. Header Branch connection Valve Flange Expansion joint Expansion loop Pipe support Reducer Elbow
PIPING COMPONENTS Piping components are mechanical elements suitable for joining or assembly into pressure-tight fluid containing piping systems. Components include pipe, tubing, fittings, flanges, gaskets,
More informationRing Type Joint CALVOSEALING DESCRIPTION
CALVOSEALING Ring Type Joint DESCRIPTION Ring Type Joints are metal ring to be used with elevated pressure and temperature applications. The sealing contact area results very reliability. Sealing gasket
More informationROYAL ULTRA-PRECISION ER COLLETS " TIR
ROYAL C EXPANDING COLLETS q Unlike chucks and most collets that grip the OD of a workpiece, C expanding collets are designed to grip on the ID of a part. q Accu-length design ensures precise workpiece
More informationANSI ORIFICE FLANGES METAL-KOREA
METAL-KOREA ANSI ORIFICE FLANGES ORIFICE FLANGES are widely used in conjunction with orifice meters for measuring the rate of flow of liquids and gases. They are basically the same as standard welding
More informationCalculations per ABS Code along with ASME Sec. VIII Div.1 XXXX
Calculations per ABS Code along with ASME Sec. VIII Div.1 XXXX Grouping of Boilers and Pressure Vessels: PART 4 CHAPTER 4 SECTOIN 1 Table #2 and #3 >> Group II PART 4 CHAPTER 4 SECTOIN 1 Appendix 1 Rules
More informationAF-4 Grooved Flange Adapter
SUBMITTAL INFORMATION PROJECT NAME: ENGINEER: CONTRACTOR: SPEC. SECTION: MEMBER FEATURES & ADVANTAGES Designed for connecting ANSI/AWWA C110/A21.10 and ASME/ANSI B16.1 Class 125/ flanged end components
More information( This link will provide you with a list of all ISO-6983 G-Codes
CUSTOM HAZARDS CUSTOM HAZARDS CUSTOM HAZARDS In this lesson I am going to explain how to circle interpolate a 1/8-27 NPT with a formed thread E-Mill using G-Code on a vertical mill. I have provided the
More informationThis specification describes the minimum requirements for piping systems for the following service:
SPEC-3501 1/ 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Instrument Air Design Conditions 150 PSIG @ 180 F Operating Conditions 125
More informationNote: Do not bury sulphur dioxide lines Use stainless steel pipe and fittings only where specified on project drawings.
1/7 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Liquid and High Pressure Gaseous Dry Sulphur Dioxide (Less than 100 ppm of water)
More informationFNW can handle all your hanger and fastener needs, all in one place. FNW products are sold exclusively at Ferguson.
FASTENERS PIPE HANGERS, SUPPORTS & STRUT ACCESSORIES FNW can handle all your hanger and fastener needs, all in one place. FNW products are sold exclusively at Ferguson. Quick Reference Nuts Heavy Hex Nuts...4
More informationR21
style r Dimensions in mm approx. pressure class ratings pitch width height of ring distance gasket weights, lbs. ring ansi, BS & mss api (psi) diameter Between of ring no. 150 300/600 900 1500 2500 2000/3000
More informationOIL INDIA LIMITED (A Govt. of India Enterprise) P.O. Duliajan , Assam. Fax No ,
Page : 1 / 4 10 03548380 OIL INDIA LIMITED (A Govt. of India Enterprise) P.O. Duliajan-786602, Assam. Fax No. 91-374-2800533, E-mail:material@oilindia.in Tender No. TUBING HEAD SPOOL Tubing Head Spool
More informationHow to Identify a PBM VALVE SERIES
How to Identify a PBM VALVE SERIES Series 0 (SP, DP, MP) 1. If it is a manual valve, the handle generally would be made of a cast iron or cast bronze. 2. If it is a manual valve, the stem at the very top
More informationStargrip series 3000 Mechanical Joint Wedge Action Restraint for Ductile Iron Pipe
Stargrip series 3000 Mechanical Joint Wedge Action Restraint for Ductile Iron Pipe INFORMATION The Stargrip Mechanical Joint Restraint System is a unique product with a proven design that provides an exceptional
More informationA Full Line of Pipe Products for Any Application
Standard Pipe SureThread and ERW: Setting the standard in the standard pipe industry With a tradition of service and quality that s 80-plus years strong, Wheatland Tube is the only domestic, full-line
More informationThis specification describes the minimum requirements for piping systems for the following service:
201/01/13 1/ 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Service Air Design Conditions Operating Conditions Blast Air (see Note 1)
More informationUnit4 31. UnitS 39. Unit 6 47
Preface..................... xi About the Author......... xiii Acknowledgments... xiv Unit 1 1 Bases for Interpreting Drawings........ I Visible Lines............. 3 Lettering on Drawings... 3 Sketching...
More informationDEUTSCH Instructional Manual for HDP-400 Power Crimper (TE CONNECTIVITY PN )
ORIGINAL INSTRUCTIONS DEUTSCH Instructional Manual for HDP-400 Power Crimper (TE CONNECTIVITY PN 1606312-1) Instruction Sheet 0425-034-0000 15 JAN 18 Rev H NOTE All numerical values are in metric units
More informationASME B (Revision of ASME B ) Orifice Flanges
(Revision of ASME B16.36-1996) Orifice Flanges A N A M E R I C A N N A T I O N A L S T A N D A R D (Revision of ASME B16.36-1996) Orifice Flanges AN AMERICAN NATIONAL STANDARD Three Park Avenue New ork,
More informationChapter 7. Fasteners
Chapter 7 Fasteners LEARNING OBJECTIVES After studying this chapter, students will be able to: Identify several types of fasteners. Explain why inch-based fasteners are not interchangeable with metric-based
More informationIntermediate Mathematics League of Eastern Massachusetts
Intermediate Mathematics League of Eastern Massachusetts Meet # 2 December 2000 Category 1 Mystery 1. John has just purchased five 12-foot planks from which he will cut a total of twenty 3-inch boards
More informationLocation. Established in 2015 Office location: Klepp Næringspark, Norway.
Location Established in 2015 Office location: Klepp Næringspark, Norway. Vision to be leader within On-Site machining & Decommissioning segment with a main focus on mature plants, offshore installations,
More informationStandard Specification for Quenched and Tempered Steel Bolts and Studs 1
Designation: A 44 00 Standard Specification for Quenched and Tempered Steel Bolts and Studs This standard is issued under the fixed designation A 44; the number immediately following the designation indicates
More informationHorizontal Cable Systems
ALUMINUM RAILING INSTALLATION INSTRUCTIONS Horizontal Cable Systems 1) Check Contents Of Packages: Verify that all parts have arrived and that they match the packing list. 1A) Coastal applications: Confirm
More informationNAVSEA STANDARD ITEM T9074-AS-GIB-010/271, Requirements for Nondestructive Testing Methods
NAVSEA STANDARD ITEM ITEM NO: 009-48 DATE: 29 JUL 2011 CATEGORY: II 1. SCOPE: 1.1 Title: Pressure Seal Bonnet Valve; repair (shop) 2. REFERENCES: 2.1 S9086-CJ-STM-010/CH-075, Fasteners 2.2. T9074-AS-GIB-010/271,
More informationHow to Use This Section
MC0118-1 Jan. 2018 How to Use This Section Determine which type of stud yoke you need by referring to the illustrations and descriptions at the top of each page. To identify a cv centering assembly (End
More informationAugust 2015 Fastener Industry Technology Update from the IFI
INDUSTRIAL FASTENERS INSTITUTE August 4, 2015 August 2015 Fastener Industry Technology Update from the IFI 1. Standards Organizations Activities a. Standards published recently: i. ASTM A563 - Standard
More informationcreated by: The Curriculum Corner
created by: The Curriculum Corner I can understand fractions. I can show and understand that fractions represent equal parts of a whole, where the top number is the part and the bottom number is the total
More informationCompleted project drawing (dimensions added for reference)
CHAPTER 5 Fundamentals IV PROJECT EXERCISE This project exercise provides point-by-point instructions for setting up the drawing with layers and then creating the objects shown in the accompanying figure.
More informationSwivel Hoist Ring RIGGING ACCESSORIES. Color coded to distinguish between UNC (Red) and Metric (Silver) thread types.
RIGGING ACCESSORIES Color coded to distinguish between UNC (Red) and Metric (Silver) thread types. Available in UNC and Metric thread sizes. UNC threads available in sizes from 800 pounds to 100,000 pounds,
More informationStandard Specification for High-Strength Bolts for Structural Steel Joints [Metric] 1
Designation: A 325M 00 METRIC An American National Standard Standard Specification for High-Strength Bolts for Structural Steel Joints [Metric] 1 This standard is issued under the fixed designation A 325M;
More informationMSR/MSB Mechanical Setting Tool
Tech Unit No: 0620000004 Revision: B Approved By: Quality Engineer Date: 2014-12-16 MSR/MSB Mechanical Setting Tool FEATURES: Special designed Bow Spring provides positive control and allows one size Mechanical
More informationU.S. Solar Mounts TOP Mount Installation Instructions. Adjustable 4 (2) 60-Cell Module Top-of-Pole Mount REV 1
U.S. Solar Mounts 4260 TOP Mount Installation Instructions Adjustable 4 (2) 60-Cell Module Top-of-Pole Mount REV 1 Ultra-Rugged Solar Mounting Solutions 2017 U.S. Solar Mounts Corp. All Rights Reserved
More informationOWNER: POSITION AUTHOR: POSITION Dan Boettcher Director of Engineering Richard Richardson Vice-Dir of Engineering
KRESS CORPORATION ENGINEERING Design of Thru and Threaded Holes Standard DOC ID 095007 REVISION A TYPE PORTAL OWNER: POSITION AUTHOR: POSITION Dan Boettcher Director of Engineering Richard Richardson Vice-Dir
More informationThreaded Products Gaskets & Seals Precision Machining
Threaded Products Gaskets & Seals Precision Machining FIRST CALL, ONLY CALL Dan-Loc Group was formed with the merger of Texthread, Dan-Loc Bolt & Gasket, and Spensall. Dan-Loc Group is a manufacturer and
More informationGovernment Recognized Export House OHSAS 18001:2007 ISO 14001:2004 PED Approved Company.
Government Recognized Export House OHSAS 800:200 ISO 400:2004 PED Approved Company. Phone : +9 22 44 (2 Lines) Fax : +9 22 289 4 Email : export@reliablepipes.com domestic@reliablepipes.com Designation:
More informationW-K-M Model MA-1 DynaCentric Butterfly Valve
Page 1 of 16 R E P A I R M A N U A L W-K-M Model MA-1 DynaCentric Butterfly Valve Page 2 of 16 Published October 2001 W-K-M and DynaCentric are trademarks of Cooper Cameron Corporation Cooper Cameron Corporation,
More informationSURE-GRIP EXPANDING COLLET SYSTEMS
SURE-GRIP EXPNDING COLLET SYSTEMS Turning Milling Grinding Workholding The Hardinge ID Gripping dvantage Years of experience in manufacturing standard expanding collets and special expanding systems brings
More informationWellhead and Production Equipment Catalogue January 2017
Wellhead and Production Equipment Catalogue January 2017 Rev. 0 Table of Content About Us................................ 4 Drilling Systems.......................... 7 Conventional Equipment...................
More information19" EIA SRD Swing Rack Installation Instructions
19" EIA SRD Swing Rack Installation Instructions (UL60950-1/UL2416 SRD Series Equipment Rack) 1-866-TRY-GLCC (879-4522) PREFACE This manual is provided to prevent service personnel from committing an act
More informationStock Programme Scope of Supply. v
Scope of Supply v2.10 2018 Pipe: Seamless Stainless Steel ASTM A312 ASME B36.19 TP316/316L DN15 DN250 10S 160 Stainless Steel ASTM A312 ASME B36.19 TP304/304L DN15 DN200 10S 160 Low Temp ASTM A333 ASME
More informationWe Are the Worldwide Provider for All Your Valve and Fitting Needs
Product Catalog We Are the Worldwide Provider for All Your and Fitting Needs C&C strives to earn your business by offering an extensive line of high quality products with a proven track record for successful
More informationTABLE OF CONTENTS Page
2 American Petroleum Institute TABLE OF CONTENTS Page POLICY................t... 8 FOREWORD......................................................................................................................f...
More informationHEADLINE BUILDING MATERIALS
EADLINE BUILDING MATERIALS eb: www.hbm.ae l Email: commercial@hbm.ae eavy ex Structural Bolts ASTM A 325M Metric Series Dimensions P.O. Box 37366, Dubai, UAE l Tel: +971 4 3475675 l Fax: +971 4 347 5485
More informationPARTITION INSTALLATION INSTRUCTIONS
PARTITION INSTALLATION INSTRUCTIONS 2015 Chevrolet Tahoe PPV / Part Number 5703FW, FWA & FEW Do not attempt to install this product on any vehicle equipped with third row seating! Parts List Distributed
More informationOrdering example: WSK-600 / B x H x L = 155 mm. M8 hexagon head screw, fixed by a locknut. Threaded bolt
Ordering example: / B x H x L = 155 mm P-3464/5595-MPA BS General / ordering example Dimensions B (width) x H (height) in mm (always corresponds to the clear shaft or smoke control damper dimensions) Available
More informationHow-To Set-Up Vise Sensors, Schunk- 5mm Sensors Step 1 - Summary
How-To Set-Up Vise Sensors, Schunk- 5mm Sensors Step 1 - Summary Vise sensors are used during operation to detect part or jaw fumbles. For example, empty jaws loaded into the vise, jaws loaded with a part
More information01 FASTENERS JULY FASTENERS 1
01 FASTENERS 4 Bolts 22 Socket Screws 30 Nuts 39 Washers 53 Screws 72 Threaded Rods & Studs 73 Rivets, Rivnuts & Accessories 82 Retaining Rings 84 Pins, Links, & Sleeves 91 Key Stock & Assortments 90 Anchors
More informationToll Free: Tel: Fax: Reynolds Bridge Road Thomaston, CT Catalog
Zero Check Precision Gages for Industry Z- Check.0001" Tolerance Plugs 1 Customer Specified Steel Plugs 2 Chrome Plated Steel Plugs 3 Steel Rings 4 Flange Steel Rings 5 Carbide Rings 6 Trilocks 7 Taperlocks
More informationALUMINUM RAILING INSTALLATION INSTRUCTIONS. 1) Check Contents Of Packages: Verify that all parts have arrived and that they match the packing list.
ALUMINUM RAILING INSTALLATION INSTRUCTIONS AF#2010-308A Glass Infill Systems 1) Check Contents Of Packages: Verify that all parts have arrived and that they match the packing list. 2) Gather and Identify
More informationDynaPower Generation II
DynaPower Generation II Return to DYNAPOWER index Return to MAIN index GENERATION II 2.0 DYNAPOWER MODEL 2.0 VARIABLE PUMP PARTS DRAWING GENERATION II 2.0 DYNAPOWER MODEL 2.0 VARIABLE PUMP PARTS DRAWING
More informationa) If a bolt is over-tightened, which will fail first the bolt, or the plastic?
2.2.75 6.525 Problem Set 3: Solutions to ME problems Fall 2013 Jacob Bayless Problem 1: Bolted joint a) If a bolt is over-tightened, which will fail first the bolt, or the plastic? The bolt is made of
More informationA Full Line of Pipe Products for Any Application
Standard Pipe Standard Pipe: SureThread and ERW Setting the standard in the standard pipe industry With a tradition of service and quality that s 80-plus years strong, Wheatland Tube is the only domestic,
More informationPrecision Chucks for Improved Accuracy and Increased Productivity
Precision Workholding Technology Precision Chucks for Improved Accuracy and Increased Productivity Precision Air Chucks (Self Contained Design) MicroCentric Precision Air Chucks feature a patented open
More informationQUALITY ASSURANCE SPECIFICATION
Page 1 of 8 QAS: 2.02 QUALITY ASSURANCE SPECIFICATION REVISION: 0 DATE: 08/29/14 MATERIAL PURCHASING Code Material Purchase Specification for Pipe, Valves, Fitting, and Flanges PAGE 1 OF 8 1.0 Purpose
More informationFIRE PROTECTION PRODUCTS
FEATURES Rev. 7-11 Mueller Indicator Post are used in fire protection systems and perform several functions. The Indicator Post provides a means to operate a buried or otherwise inaccessible valve. Also,
More informationThe Ultimate Critical Service Triple Offset Valve INSTALLATION, OPERATION & MAINTENANCE MANUAL
INSTALLATION, OPERATION & MAINTENANCE MANUAL Operation Table of Contents 1.0 Introduction 2 2.0 Safety Information 2 2.1 Definition of Terms 2 2.2 ATEX Directive 94/9/EC 2 2.2.1 Marking 3 2.2.2 Special
More informationHARDINGE Installation booklet For:
HARDINGE Installation booklet For: L Flange Nose Dead-Length Collet Adaptation Chucks Draw Collet Read the enclosed instructions and recommendations before any installations WARRANTY & RETURN PROCEDURES
More informationNAVSEA STANDARD ITEM
NAVSEA STANDARD ITEM FY-19 DATE: 01 OCT 2017 CATEGORY: I 1. SCOPE: 1.1 Title: Threaded Fastener Requirements; accomplish 2. REFERENCES: 2.1 Standard Items 2.2 S9086-CJ-STM-010/075, Fasteners 3. REQUIREMENTS:
More informationROLL-NECK BEARINGS DESIGN, TYPES, AND FEATURES TOLERANCES AND RUNNING ACCURACY RECOMMENDED FITS
ROLL-NEK EARINGS TAPERED ROLLER EARINGS YLINDRIAL ROLLER EARINGS ore Diamete00 939.800mm 338 ore Diamete00 90mm 340 DESIGN, TYPES, AND FEATURES Four-row tapered roller bearings and four-row cylindrical
More informationThe Ultimate Critical Service Triple Offset Valve INSTALLATION, OPERATION & MAINTENANCE MANUAL
INSTALLATION, OPERATION & MAINTENANCE MANUAL For more information on this product and other bray products please visit our website www.bray.com Operation Table of Contents 1.0 Introduction 2 2.0 Safety
More informationHex Cap Screws Coarse & Fine Thread
INDUSTRIAL Product Description Hex head cap screws are manufactured to dimensional standards of ASME B18.2.1 and to various material and mechanical standards of ASTM and SAE. The length of a cap screw
More informationPIONEER TRADING CO., LTD.
PRECISION KURODA LTD. OIL COUNTRY GAUGES API THREAD GAUGES PREMIUM CONNECTION GAUGES THREAD MEASURING INSTRUMENTS CONTACT TO: PIONEER TRADING CO., LTD. 4-1 Kuzuha-Asahi 3-Chome Hirakata Osaka 573-1111,
More informationBritish Standard Pipe Tapered
British Standard Pipe Tapered Information / Identification BSPT connections, just as NPT connections, seal by thread interference. BSPT connections are the same as JIS Tapered Pipe, Whitworth Tapered Pipe
More informationC-15 Truck Engine 9NZ00001-UP(SEBP ) - Document Structure. Media Number -RENR Publication Date -01/07/2008 Date Updated -22/07/2008
Page 1 of 8 Shutdown SIS Previous Screen Product: TRUCK ENGINE Model: C-15 TRUCK ENGINE 9NZ Configuration: C-15 Truck Engine 9NZ00001-UP Disassembly and Assembly C-15, C-16 and C-18 Truck Engines Media
More informationMSR/MSB Mechanical Setting Tool
Tech Unit No: 0620000004 Revision: C Approved By: Quality Engineer Date: 201-1-9 MSR/MSB Mechanical Setting Tool FEATURES: Special designed Bow Spring provides positive control and allows one size Mechanical
More informationAttachment Illustrated Parts List
Attachment Illustrated Parts List Attachment Mfg. No. Description 1695168 Catcher, Clean Sweep Twin, 38" MANUFACTURING, INC. 500 N. Spring Street / PO Box 997 Port Washington, WI 53074-0997 USA Part No.:
More informationHydraulic Tensioner Assembly: Load Loss Factors and Target Stress Limits
Proceedings of the ASME 214 Pressure Vessels & Piping Conference PVP214 July 2-24, 214, Anaheim, California, USA PVP214-28685 Hydraulic Tensioner Assembly: Load Loss Factors and Target Stress Limits Warren
More informationUL / FM E-1 FIRE PROTECTION PRODUCTS INDICATOR POST FEATURES. *Applies to "ORDER LENGTH" codes B through F; code A has 22" adjustment.
UL / FM MUELLER Indicator Post are used in fire protection systems and perform several functions. The Indicator Post provides a means to operate a buried or otherwise inaccessible valve. Also, the Indicator
More informationDETAIL SPECIFICATION SHEET FITTING, INSTALLATION, FLARED TUBE AND HOSE, SWIVEL
INCH-POUND MS33786B 12 February 2013 SUPERSEDING MS33786A 1 February 1985 DETAIL SPECIFICATION SHEET FITTING, INSTALLATION, FLARED TUBE AND HOSE, SWIVEL This specification is approved for use by all Departments
More informationSERVICE PARTS MANUAL
SERVICE PARTS MANUAL SNO-WAY SPREADERS 4 CUBIC FOOT 6 CUBIC FOOT & 9 CUBIC FOOT 01 Sno-Way International 91019B TABLE OF CONTENTS Page PARTS LIST INTRODUCTION... HOPPER FRAME - 4 CUBIC FOOT (For Serial
More informationcaroma marc newson wall basin mixer
caroma marc newson wall basin mixer water efficient tapware (nominal flow rate = 5 L/min) PLUMBERS INSTALLATION INSTRUCTIONS IS1213A(07/12) Important Information Brazed connections should NOT be made directly
More informationHARDINGE WORKHOLDING. Sure-Grip Expanding Collet Systems
HARDINGE WORKHOLDING Sure-Grip Expanding Collet Systems 800-843-8801 www.hardinge.com The Hardinge ID Gripping Advantage Hardinge Sure-Grip Expanding Collet Systems offer solutions to difficult machining
More informationSECTION THERAPEUTIC POOL ACCESSORIES
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 13 17 23.11 THERAPEUTIC POOL ACCESSORIES SPEC WRITER NOTES: Delete between // // if not applicable to project. Also, delete any other item or paragraph not applicable
More informationS. GURESH 4 JAN 2017 S. JOHNSON 4 JAN 2017
PAGE 2 OF 15 1.0 PURPOSE This Inspection Method describes the methodology for Ultrasonic Examination using manual and semi-automatic techniques by the contact and immersion longitudinal wave method and
More informationAC : CLARIFICATIONS OF RULE 2 IN TEACHING GEOMETRIC DIMENSIONING AND TOLERANCING
AC 2007-337: CLARIFICATIONS OF RULE 2 IN TEACHING GEOMETRIC DIMENSIONING AND TOLERANCING Cheng Lin, Old Dominion University Alok Verma, Old Dominion University American Society for Engineering Education,
More informationCAUTION! This manual contains important information for the correct installation, operation and maintenance of the equipment described herein.
CAUTION! This manual contains important information for the correct installation, operation and maintenance of the equipment described herein. All persons involved in such installation, operation, and
More informationSection COUPLINGS AND COUPLING ADAPTERS. This Section covers couplings and coupling adapters for ductile iron and steel pipe.
PART 1 GENERAL 1.01 SUMMARY Section 15155 This Section covers couplings and coupling adapters for ductile iron and steel pipe. 1.02 MEASUREMENT AND PAYMENT A. No separate payment for Work performed under
More informationTYPE J (20 FT - 40 FT) MICHIGAN DEPARTMENT OF TRANSPORTATION 10-0" 7-6" NOTE: sheet 5 & 6 of 10) DEPARTMENT DIRECTOR. Kirk T.
Column truss connection Chord splice (see details (See details sheets 3 & 4 of 10) s Top truss chord Free end panel 10-0" Support end panels length varies (See chart below) \ Truss Back truss chord Top
More information19" EIA SRD Swing Rack Installation Instructions
19" EIA SRD Swing Rack Installation Instructions 1-866-TRY-GLCC (879-4522) PREFACE This manual is provided to prevent service personnel from committing an act that results in the risk of fire, electric
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationMidmark Stainless Steel Cages Setup Manual
Midmark Stainless Steel Cages Setup Manual Table of Contents Pre-Installation......................... 2 Parts Identification..................... 2-3 Base Construction....................... 3 Assembly............................
More informationPREVIEW COPY. Table of Contents. Lesson One Using the Dividing Head...3. Lesson Two Dividing Head Setup Lesson Three Milling Spur Gears...
Table of Contents Lesson One Using the Dividing Head...3 Lesson Two Dividing Head Setup...19 Lesson Three Milling Spur Gears...33 Lesson Four Helical Milling...49 Lesson Five Milling Cams...65 Copyright
More information