PIPING NOMENCLATURE. Header Branch connection Valve Flange Expansion joint Expansion loop Pipe support Reducer Elbow
|
|
- Reynard Shepherd
- 5 years ago
- Views:
Transcription
1 PIPING COMPONENTS Piping components are mechanical elements suitable for joining or assembly into pressure-tight fluid containing piping systems. Components include pipe, tubing, fittings, flanges, gaskets, bolting, valves and devices such as expansion joints, flexible joints, pressure hoses, traps, strainers, in-line portions of instruments.
2 PIPING NOMENCLATURE
3 PIPING NOMENCLATURE Header Branch connection Valve Flange Expansion joint Expansion loop Pipe support Reducer Elbow
4 PIPING SYSTEM Branch Run Continued...
5 PIPE MANUFACTURING
6 SEAMLESS PIPE - Manufacturing Billet preparing visual control Billet chopping Billet heating in annular furnace Rough tube piercing Tube rolling in continuous mandrel mill Mandrel removing Continued...
7 SEAMLESS PIPE - Manufacturing Tube heating in cell induction furnace Sizing and reduction Stalk ends cutting, tubes cutting with flying shears Tubes cooling Tubes leveling Tubes cutting in ready sizes, tubes facing Continued...
8 SEAMLESS PIPE - Manufacturing Geometry measuring, mechanical tests, chemical composition control Tube ends sizing (by OD and ID) Heating for quenching Quenching in sprayer Tempering Tubes cooling Continued...
9 SEAMLESS PIPE - Manufacturing Tubes etching Ultrasonic or electromagnetic test Hydraulic test Sweeping-up (if required), visual control Preservative coating Weighing, marking, packing, storing Continued...
10 ERW PIPE - Manufacturing Continued...
11 ERW PIPE - Manufacturing Slitting: HR Coils are slotted to pre-determined widths for each and every size of pipes Uncoiling, End Shearing And Welding: The slotted coil is uncoiled at the entry of ERW mill and the ends are sheared and welded one after another. This results in a single endless strip. Forming: The slotted coils are initially formed into U shape and after that into a cylindrical shape with open edges utilizing a series of forming rolls. Continued...
12 ELECTRIC RESISTANCE WELDED PIPE Welding: Welding In this stage, the open edges are heated to the forging temperature through high-frequency, lowvoltage, high current and press welded by forge rolls making perfect and strong but weld without filler materials. De Beading: In this stage, the weld flash on top and inside (if required) is trimmed out using the carbide tools. Continued...
13 ELECTRIC RESISTANCE WELDED PIPE Seam Annealing: If required, the welding portion and heat affected zone is put to normalizing and then are cooled down in a air cooling bed. Sizing: After water quenching, slight reduction is applied to pipes with sizing rolls. This results in producing desired accurate outside diameter. Continued...
14 ELECTRIC RESISTANCE WELDED PIPE Cutting: In cutting stage, the pipes are cut to required lengths by flying cut off disc/saw cutter. End Facing And Bevelling: This is usually stage, where the pipes ends are faced and bevelled by the end facer. All these processes are continuous with automatic arrangements. These plain ended tubes further go for processing as per the customer requirements such as galvanizing, threading, black varnishing and more.
15 PIPE CLASSIFICATION NPS: Nominal pipe size. T Wall Thickness OD: Outside Diameter
16 PIPE - Definition Pipe is a tube with round cross section conforming to the dimensional requirements of Governing standards For EX ASME B36.10M Welded and Seamless Wrought Steel Pipe ASME B36.19M Stainless Steel Pipe Commonly designated by nominal pipe sizes and American National Standards Institute's schedule numbers.
17 PIPE SIZE Nominal pipe size (NPS) is a dimensionless designator of pipe size. It indicates standard pipe size when followed by the specific size designation number without an inch symbol. NPS 12 and smaller pipe has outside diameter greater than the size designator Ex: NPS 2 indicates a pipe whose Outside Diameter is in. NPS 14 and larger pipe is the same as the size designator in inches. Ex: NPS 14 pipe has an Outside Diameter equal to 14 in.
18 PIPE SIZE Diameter nominal (DN) is also a dimensionless designator of pipe size in the metric unit system, developed by ISO. It indicates standard pipe size when followed by the specific size designation number. For example, DN 50 is the equivalent designation of NPS 2.
19 PIPE SIZE NPS and DN pipe size equivalents: NPS DN NPS DN NPS DN NPS DN 1/8 6 3 ½ ¼ / ½ ¾ ¼ ½ ½ For sizes larger than NPS 80, determine the DN equivalent by multiplying NPS size designation number by 25 without a millimetre symbol.
20 PIPE THICKNESS In the beginning, each pipe size was produced to have one thickness, which later was termed as standard (STD) As the industrial requirements demanded the handling of higher-pressure fluids, pipes were produced having thicker walls, which came to be known as extra strong (XS) or extra heavy (XH). The higher pressure requirements increased further, requiring thicker wall pipes. Accordingly, pipes were manufactured with double extra strong (XXS) or double extra heavy (XXH) while the standardized outside diameters are unchanged.
21 PIPE THICKNESS With the development of stronger and corrosion-resistant piping materials, the term schedule (SCH) was invented to specify the various nominal wall thickness of pipe. Schedule numbers are 5, 5s, 10, 10s, 20, 20s, 30, 40, 40s, 60, 80, 80s, 100, 120, 140, 160 The schedule numbers followed by the letter S are per ASME B36.19M, and they are primarily intended for use with stainless steel pipe.
22 PIPE THICKNESS Original pipe wall thickness designations of STD, XS, and XXS have been retained; however, they correspond to a certain schedule number depending upon the nominal pipe size. The nominal wall thickness of NPS 10 and smaller schedule-40 pipe is same as that of Standard Wall Thickness pipe. Also, NPS 8 and smaller schedule-80 pipe has the same wall thickness as XS pipe. (Refer Sch. Chart)
23 PIPE THICKNESS Schedule Chart NPS OD S5s S10s S10 S20 S30 S40s STD S40 S60 S80s X-S S80 S100 S120 S140 S160 XX-S 1/ / / / /
24 PIPE CLASSIFICATION Schedule Chart NPS OD S5s S10s S10 S20 S30 S40s STD S40 S60 S80s X-S S80 S100 S120 S140 S160 XX-S Reference: ASME B36.10M, ASME B36.19M
25 PIPE SUPPLY Dimensions Dimensions NPS 1/8, ¼, 3/8, ½, ¾, 1, 1 ½, 2, 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 24, 28, 30, 32, 36, 40, 44, 48 52, 56, 60 NPS 1 ¼, 2 ½, 3 ½, 5 not used Pipe is supplied in o Random length (18 to 25 ft) o Double random length (38 to 48 ft)
26 PIPE SUPPLY Pipe End PE (Plain End) TE (Treaded End BE (Bevel End)
27 PIPING MATERIAL CLASSIFICATION API Line pipe grade designations come from API Spec 5L specification for line pipe has Grade designation A& B. Stronger grades have the designation X followed by the specific Minimum Yield Strength of the pipe steel measured in ksi (kilo pounds per square inch) For example API 5L X60 denotes, pipe having a minimum yield strength of 60ksi
28 PIPING MATERIAL CLASSIFICATION API API 5L Line Pipe Physical Properties API 5L GRADE YIELD STRENGTH MIN. (ksi) TENSILE STRENGTH MIN. (ksi) A B X X X X X X X X
29 Tube Tube Specify by two of Outside diameter Inside diameter Wall thickness o Thousandths of inch o Gauge number American wire gauge Steel wire gauge. Etc..
30 Tube Thickness - Gauge
31 ASTM Spec Some of the commonly used American Spec & Product Form Specification Product form Application ASTM A53 Seamless/welded Ordinary use in gas, air, oil, water, steam ASTM A106 Seamless High-temperature service (steam, water, gas, etc.) ASTM A369 Forged and bored High-temperature service ASTM A335 Seamless High-temperature service ASTM A333 Seamless/welded Service requiring excellent fracture toughness ASTM A671 Electric fusion-welded Low-temperature service ASTM A672 Electric fusion-welded Moderate-temperature service ASTM A691 Electric fusion-welded High-temperature service ASTM A312 Seamless/welded Low- to high-temperature and corrosive service API 5L Seamless/welded Line pipe, refinery, and transmission service
32 PIPING SYSTEM Branch Pipe Branch connections may be made by welding the branch pipe or a welding outlet fitting to the run pipe Connections for branch pipes are made with pipe tees or stubins/ stub-ons. Reinforcement Pad: Material added in the vicinity of a branch opening to restore the mechanical integrity of the pipe.
33 PIPING SYSTEM - Branch Connection Stub In/ Stub on: Welded directly in the side of the main pipe run Cab be reinforced
34 PIPING SYSTEM - Branch Connection Stub In/ Stub on: Stub-in/ Stub-on can replace a reducing tee in joining branch pipes. A hole of the diameter of the stub-in pipe is drilled into the main pipe and the pipes are fitted together. The stub-in pipe and main pipe are then welded together. Advantage is that it avoids the cost of buying pipe fittings Save installation time because One weld is needed around the stub hole where as 3 joints are required in reducing tee
35 PIPING SYSTEM - Branch Connection Stub Outs: Capped and unused pipe branch connections or stubs on pipes are called stub outs. They are capped until a branch pipe is attached. The branch pipe can be inserted after the pipe cap is removed. Continued...
36 PIPING SYSTEM - Branch Connection Stub Outs: Continued...
A Full Line of Pipe Products for Any Application
Standard Pipe SureThread and ERW: Setting the standard in the standard pipe industry With a tradition of service and quality that s 80-plus years strong, Wheatland Tube is the only domestic, full-line
More informationA Full Line of Pipe Products for Any Application
Standard Pipe Standard Pipe: SureThread and ERW Setting the standard in the standard pipe industry With a tradition of service and quality that s 80-plus years strong, Wheatland Tube is the only domestic,
More informationThis specification describes the minimum requirements for service water piping systems (ie: cooling water, process water, etc.), located on surface.
SPEC-3500 1/9 1.0 PURPOSE This specification describes the minimum requirements for service water piping systems (ie: cooling water, process water, etc.), located on surface. Note: This specification does
More informationKerkau Manufacturing. B16.5 Flange Book
Kerkau Manufacturing B16.5 Flange Book TABLE OF CONTENTS Revision 1 Title Page Table of Contents Tolerance Page Permissible Imperfections Dimensions of Flange Facings (all pressure rating classes) Dimensions
More informationThis specification describes the minimum requirements for piping systems for the following service:
201/11/2 1/9 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Underground Service Water Note: This specification does not apply to piping
More informationThis specification describes the minimum requirements for piping systems for the following service:
SPEC-3004 1/7 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Service Water Design Conditions Operating Conditions 10 PSIG @ 33 o F to
More informationNote: Do not bury sulphur dioxide lines Use stainless steel pipe and fittings only where specified on project drawings.
1/7 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Liquid and High Pressure Gaseous Dry Sulphur Dioxide (Less than 100 ppm of water)
More informationThis specification describes the minimum requirements for piping systems for the following service:
201/01/13 1/ 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Service Air Design Conditions Operating Conditions Blast Air (see Note 1)
More informationA representative from Occupational Health is to be involved in the commissioning process to address any Respiratory Protection Program requirements.
SPEC-3017 1/8 1.0 PURPOSE This specification describes the minimum requirements for the installation of breathing air distribution systems (indoor and outdoor) up to the connection to the breathing air
More informationSECTION EXPANSION FITTINGS AND LOOPS FOR HVAC PIPING
SECTION 230516 - EXPANSION FITTINGS AND LOOPS FOR HVAC PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and
More informationFlange Dimensions Class 125 Bronze Flange Dimensions Class 300 Bronze Flange Dimensions Class 150 Bronze Flange Dimensions
Dimensions Class Bronze Dimensions Meets Ib. A.S.M.E. Stard Class 00 Bronze Dimensions Meets ANSI STD B. Nominal Dim. A O.D. Dim. B Circle Dim. C Hole No. Holes Nominal Dim. A Diam. Dim. B Min. Dim. C
More informationBasket & Screen Data. Cylindrical baskets for simplex and duplex strainers up to 8" size
Basket & Screen Data Cylindrical baskets for simplex and duplex strainers up to 8" size Slant top baskets for Model 510 simplex and Model 570 duplex strainers sizes 8" to 36" Basket and Screen Design The
More informationAUDAS. Tel: Fax: No.259 Baichi north Rd.Haiyan.Zhejiang.
Standard State SECTION A : SCREW THREAD Basic elements of screw thread design ANSI/ASME B1.7M Nomenclature.Definitions and letter symbols for screw thread ASME B1.1 Unified inch screw thread ( UN and UNF
More informationThis specification describes the minimum requirements for piping systems for the following service:
SPEC-3501 1/ 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Instrument Air Design Conditions 150 PSIG @ 180 F Operating Conditions 125
More informationSteel Nipples. Nipples & Fittings. Black and Galvanized Steel Nipples. Black and Galvanized. Steel Nipples. 142
PRODUCT SPECIFICATIONS Welded steel pipe nipples both galvanized an dblack in diameters ranging from 1/8 up to 4 in lengths from close to 12 and cut-pipe up to 120. TECHNICAL SPECIFICATIONS Standards:
More informationREPUTE tube fittings are manufactured to stringent quality control program and internal standards which
Introduction: REPUTE tube fittings are manufactured to stringent quality control program and internal standards which assure the highest quality available in the industry. Two ferrule tube fittings are
More information.1 Materials and installation for steel piping, valves and fittings for hydronic systems in building services piping..2 Related Sections.
Issued 2006/08/01 Section 15183 Hydronic Systems: Steel Page 1 of 6 PART 1 GENERAL 1.1 SUMMARY.1 Section Includes..1 Materials and installation for steel piping, valves and fittings for hydronic systems
More informationEssex County College - West Essex Campus Addition And Renovations dlb # / SECTION EXPANSION FITTINGS AND LOOPS FOR HVAC PIPING
SECTION 230516 - EXPANSION FITTINGS AND LOOPS FOR HVAC PIPING PART I - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and
More informationALUMINUM PIPE GUIDERAIL 01/01/
NOTES PIPE RAILING & POSTS: Structural Tube, Pipe and Bar shall be in accordance with ASTM B22 or ASTM B429, Alloy 606-T6. End Rail 90 bends and corner bends with maximum 4-0" post spacing, may be Alloy
More informationGOST TUBING AND COUPLINGS
GOST 633-80 TUBING AND COUPLINGS Tubing is used for oil and gas production. Tubing shall be made seamless, plain- or upset end and couplings with high-seal connections. Coupling-free connections are possible.
More informationActivating Your Ideas. In Stainless Steel Pipe
Activating Your Ideas In Stainless Steel Pipe Applications Outokumpu produces austenitic and duplex pipe products from small diameter pipe to large diameter, heavy wall pipe, with thicknesses up to 2 on
More information5/16" Flange nut. Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc plated bolt w/ washers and nut. Anchor 3" sq. 7 Ga.
2 1/2" x 2 1/2" x 10 Ga. 6" 5" 4" Variable Slipbase (8" Sq. SYS.) 5/16 Corner Bolt W/ nut 5/16" Flange nut Stub Insert (8" Sq. SYS.) Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc
More informationFUEL GAS PIPING SECTION A. The provisions of SECTION 15010, MECHANICAL GENERAL REQUIREMENTS, apply to this section.
FUEL GAS PIPING SECTION 15355 PART 1 GENERAL 1.1 DESCRIPTION A. The provisions of SECTION 15010, MECHANICAL GENERAL REQUIREMENTS, apply to this section. B. This specification covers both interior and exterior
More informationPlumbing Part II - Hand Pump
Plumbing Part II - Hand Pump Nelson Riedel Nelson@NelsonsLocomotive.com Initial: 7/17/03 Last Revised: 06/06/2004 The hand pump located in the tender water tank is a backup pump should the axel pump fail
More informationBolts Carriage Elevator Eye Hex Shoulder Specials Square Head Step. Drills, Taps, & Bits. Hex Capscrews Grade 8 Grade 5 Grade 2 A325 A490 Specials
AU-VE-CO Bolts Carriage Elevator Eye Hex Shoulder Specials Square Head Step Concrete Anchoring Adhesives Anchor Bolts Drop Ins Wedge Pins Cotter Dowel Hitch Spring Roll Taper Pipe Fittings Power Coil EZ
More informationODOT ITB Group 4 Item 33 Qty. 1
ODOT ITB 180-17 Group 4 Item 33 Qty. 1 ODOT ITB 180-17 Group 4 Item 34 Qty. 1 ODOT ITB 180-17 Group 4 Item 35 Qty. 1 ODOT ITB 180-17 Group 4 Item 36 Qty. 1 STRUCTURAL BOLTS NUCOR FASTENER TECHNICAL
More informationQUALITY ASSURANCE SPECIFICATION
Page 1 of 8 QAS: 2.02 QUALITY ASSURANCE SPECIFICATION REVISION: 0 DATE: 08/29/14 MATERIAL PURCHASING Code Material Purchase Specification for Pipe, Valves, Fitting, and Flanges PAGE 1 OF 8 1.0 Purpose
More informationStock Programme Scope of Supply. v
Scope of Supply v2.10 2018 Pipe: Seamless Stainless Steel ASTM A312 ASME B36.19 TP316/316L DN15 DN250 10S 160 Stainless Steel ASTM A312 ASME B36.19 TP304/304L DN15 DN200 10S 160 Low Temp ASTM A333 ASME
More informationMission Statement. State Steel strives to provide quality products and services at competitive
Mission Statement State Steel strives to provide quality products and services at competitive prices. This commitment is demonstrated with several branch locations all offering large, diverse inventories
More informationStructural Bolting. Notice the Grade 5 has a much smaller head configuration and a shorter shank then the grade A325 structural bolt.
Structural Bolting ASTM F3125/F3125M is a structural bolt specification covering inch and metric bolt grades. This specification contains 4 inch series bolting grades: A325, F1852, A490, and F2280. These
More informationProcedure for Testing Direct Tension Indicators (DTI) Assemblies
Procedure for Testing Direct Tension Indicators (DTI) Assemblies 1. Scope: This test is to ensure that the bolt will be at or above the specified minimum bolt tension after installation when the direct
More information5.1 MUELLER CORPORATION VALVES. MUELLER 300 Ball Type Corporation Valves
MUELLER CORPORATION VALVES 5.1 Shaded area indicates changes Rev. 4-14 Machine inserted corporation stops were developed by Hieronymus Mueller in conjunction with his development of the drilling and tapping
More informationSTEEL PIPE GUIDERAIL 01/01/
NOTES PIPE RAILING & POSTS: Pipe Rails and s shall be in accordance with ASTM A5 Grade B for standard weight pipe and ASTM A500 Grade B, C or D or ASTM A50 for structural tube. Bars for handrail supports
More informationAnnexure - V. Specifications, Typical Drawing & Data Sheet for Split TEE (Hot Tapping Material)
Annexure - V Specifications, Typical Drawing & Data Sheet for Split TEE (Hot Tapping Material) CONTENTS SL NO. DESCRIPTION 1.0 SCOPE 2.0 REFERENCE DOCUMENTS 3.0 MANUFACTURER'S QUALIFICATION 4.0 MATERIALS
More informationPage 1 of 12 Second Revision No. 5-NFPA 12-2014 [ Section No. 2.3.4 ] 2.3.4 ASTM Publications. ASTM International, 100 Barr Harbor Drive, P.O. Box C 700, West Conshohocken, PA 19428-2959. ASTM A53, Standard
More information2016 AASHTO BRIDGE COMMITTEE AGENDA ITEM: 24 (REVISION 1) SUBJECT: LRFD Bridge Design Specifications: Section 6, Various Articles (2)
2016 AASHTO BRIDGE COMMITTEE AGENDA ITEM: 24 (REVISION 1) SUBJECT: LRFD Bridge Design Specifications: Section 6, Various Articles (2) TECHNICAL COMMITTEE: T-14 Steel REVISION ADDITION NEW DOCUMENT DESIGN
More informationSERRATING / GROOVING TOOL - ST SERIES. Features : 1/8 x3/8 x1/8
3 1 8 2-2 SERRATING / GROOVING TOOL - ST SERIES FOR GROOVING IN TUBE SHEETS Tool 1/8 x 3/8 x 1/8 Spacing Spare Tool Bits 1/8 x 1/4 x 1/8 Spacing Special Spacing 9.53 3/8 ST-375-970 ST-3703 ST-3703-S ST-3703-SPEC
More informationNew Product Release: October 2014 Boone Racks
New Product Release: October 2014 Boone Racks Double Fido Fountain Mounting: Surface NOTE: THESE ROUGH-IN DIMENSIONS MAY VARY ½: (13 mm) PLUS OR MINUS NOTE: All dimensions subject to manufacturing variance
More informationAllentown, PA - Plant Expansion Steel Pipe Spec. No. 671-S40 December 31, 2015
Steel DIVISION 15: MECHANICAL SECTION 15061: STEEL PIPE 1.0 GENERAL All materials shall be of high quality and as per the following specifications. 2.0 PRODUCTS 2.1 Specification CS-1 Service = (CA, VAC)
More informationA. Compatibility: Products shall be suitable for piping service fluids, materials, working pressures, and temperatures.
SECTION 22 05 16 LOOPS FOR PLUMBING PIPING PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationInternational Tube & Conduit Company Ltd. BRITISH STANDARD STEEL CONDUITS & FITTINGS
International Tube & Conduit Company Ltd. BRITISH STANDARD STEEL CONDUITS & FITTINGS 1 ABOUT THE COMPANY VISION STATEMENT We strive to exceed our customers expectations through leading edge technologies
More informationSteel Plate in Oil Rig Blowout Preventer Valves
Design Problem Steel Plate in Oil Rig Blowout Preventer Valves Introduction Design for Performance Alloy selection Radii and stress reduction Design for Production Mould method Orientation and cores Controlling
More informationPROTEM Tube and pipe beveling ID CLAMPING BEVELING MACHINES FOR TUBES, PIPES AND BOILER TUBES
PROTEM Tube and pipe beveling ID CLAMPING BEVELING MACHINES FOR TUBES, PIPES AND BOILER TUBES US-40 PRACTICAL TOOLS INC. P.O. Box 233 Aurora, ON L4G 3H3, Canada Phone: 905-727-0014 / 888-847-8880 Fax:
More informationClamp Pair. Bore Diameter (mm) Clamp Material PP = Polypropylene PA = Polyamide PE = Polyethylene AL = Aluminum
DIN 0 CLAMPS Clamp Pairs HRL = Standard Duty (Ribbed Profile) HRGL = Standard Duty (Smooth Profile) HRS = Heavy Duty (Ribbed Profile) HRGS = Heavy Duty (Smooth Profile) Clamp Pair ore Diameter (mm) Clamp
More informationGeneral Information. Ball Curb Valve
General Information 1. All Jones Curb Valves are manufactured in accordance with the AWWA Standard C-800-latest revision. 1. Copper Alloy CDA No. C83600 (85-5-5-5) 2. Copper Alloy CDA No. 89520 (Low Lead)
More informationMATERIAL AND EQUIPMENT STANDARD FOR METRIC TYPE FASTENERS (SCREWS, BOLTS, STUDS, NUTS AND WASHERS) ORIGINAL EDITION DEC. 1997
MATERIAL AND EQUIPMENT STANDARD FOR METRIC TYPE FASTENERS (SCREWS, BOLTS, STUDS, NUTS AND WASHERS) ORIGINAL EDITION DEC. 1997 This Standard is the property of Iranian Ministry of Petroleum. All rights
More informationTable Of Contents Casing Head 02 Christmas Tree & Tubing Head Tubing Spool 04 Contact Us
Table Of Contents Casing Head 02 Christmas Tree & Tubing Head 03 Tubing Spool 04 Contact Us 05 1 www.sapwellsglobal.com Casing Head Specialized large-diameter pipe lowered into an open hole and cemented
More informationSANDVIK 14AP FREE-CUTTING WIRE WIRE
SANDVIK 14AP FREE-CUTTING WIRE WIRE DATASHEET Sandvik 14AP is a hardenable free-cutting carbon steel characterized by excellent machinability and good wear resistance and hardness after hardening. CHEMICAL
More informationPIPE/CONDUIT SUPPORTS
PIPE/CONDUIT SUPPORTS Pipe/Conduit Clamps...102-105 Unicushion... 106 Pipe & Tubing (Cush-A-Clamp ) Clamps...107-110 Pipe Hangers... 111 Pipe Rollers...111-112 Pipe Brackets... 113 Reference Tables...114-120
More informationPRODUCT CATALOGUE. Welded Carbon Steel Pipe
Welded Carbon Steel Pipe FOR WATER BORE AND GENERAL DRILLING APPLICATIONS PRODUCT CATALOGUE Water Bore Casing to Australian Standard AS 1396 General Drilling Casing in Accordance with J.55 Grade and API
More informationRELINER INSIDE DROP SYSTEM SPECIFICATIONS
1. PRODUCT NAME RELINER INSIDE DROP SYSTEM U.S. Patent 6074130 Canadian Patent # 2269565 All RELINER Products are proudly made in the U.S.A. 2. MANUFACTURER RELINER /Duran Inc. 53 Mount Archer Rd. Lyme
More informationSection COUPLINGS AND COUPLING ADAPTERS. This Section covers couplings and coupling adapters for ductile iron and steel pipe.
PART 1 GENERAL 1.01 SUMMARY Section 15155 This Section covers couplings and coupling adapters for ductile iron and steel pipe. 1.02 MEASUREMENT AND PAYMENT A. No separate payment for Work performed under
More informationChemical composition. Type 2 as per F568: C ( ); P (max 0.048); S (max 0.058); Mn (min 0.74); B (min );
BS EN 14399 HIGH STRENGTH STRUCTURAL BOLTING FOR PRE LOAD Direct comparison as an alternative to ASTM HSFG Bolts ASTM A325M Type 1, ASTM A490M Type 1 or 2 BS EN 14399-3:2005 Grade 8.8 and 10.9 Chemical
More informationMidsteel Flanges & Fittings Ltd
Company Profile Stockist and Manufacturer s of Pipe, Flanges and Fittings for the Oil, Gas, Petrochemical, Fire Protection and Power Generation Industries. Contents Introduction to Location Stock Range
More informationAsme B31 1 Power Piping Design Standard Certification
ASME B31 1 POWER PIPING DESIGN STANDARD CERTIFICATION PDF - Are you looking for asme b31 1 power piping design standard certification Books? Now, you will be happy that at this time asme b31 1 power piping
More informationDETAILED ENGINEERING OF PROCESS PIPING SYSTEMS
LAST UPDATED 25-10-2017 DETAILED ENGINEERING OF PROCESS PIPING SYSTEMS COURSE DURATION: 5 DAYS REACH US Today for Greater Safety, Quality, Reliability, Productivity, Profitability HRD Approved Class A
More informationCall Today for a Free Quote! Immediate Availability. Inexpensive Delivery.
Call Today for a Free Quote! Immediate Availability. Inexpensive Delivery. ASTM A606-4 / A588 / A847 (AKA CORTEN ) STRUCTURAL COMPONENTS FLAT SHEETS, FLAT BAR, PLATE, COIL, RECTANGULAR TUBE, SQUARE TUBE,
More informationTIE-ROD AND PIPE JOINTS
CHAPTER 5 Machines use various parts which are joined in several ways for the machine to function as whole. We have learnt about some devices like fasteners (temporary & permanent) and some simple joints
More informationKEEP YOUR RESOURCE MOVING.
LINER BOLTS KEEP YOUR RESOURCE MOVING. COLUMBUS McKINNON CORPORATION Leading the Industry Downtime in the grinding mill operation is caused by one of two things: regularly scheduled maintenance or unscheduled
More informationDUO-TAPTITE. Fasteners DUO-TAPTITE. Thread Rolling Screws
Fasteners Percent thread chart... Page 8 Pilot hole sizes... Page 9 Typical torque performance... Page 10 Typical single punch extruded holes... Pages 11 & 12 Die cast cored holes... Page 12 CORFLEX...
More informationMidwest Roadside Safety Facility
19'-11 1/2" 6083 239'-11 1/2" 73139 Impact 1100C 25 43 5/16" 1100 upstream from the upstream face of the first shear fender downstream of the joint between barrier nos. 7 and 8 Upstream End Downstream
More informationSECTION BASIC MATERIALS AND METHODS
SECTION 15050 BASIC MATERIALS AND METHODS PART 1 - GENERAL 1.01 SECTION INCLUDES A. Pipe and Fittings. 1.02 RELATED SECTIONS A. Basic Mechanical Requirements: Section 15010. B. Supports, Anchors, and Seals:
More informationPunches. SYNEO, the leading edge in medical automation solutions, is. pleased to announce the ISO 9001:2008 certification of its Texas
Punches SYNEO MANUFACTURERS VERY PRECISE, SUPER SHARP, DURABLE, HOLE-MAKING CUTTERS FOR PLACING HOLES IN CATHETER-BASED MEDICAL DEVICES. SYNEO CUTTERS ARE MANUFACTURED TO VERY TIGHT TOLERANCES TO ENSURE
More informationLCSF Low Clearance Split Frame
Designed For Portability And Limited Clearance Full Range 2in - 48in for Pipe and Tube Optional Bridge Slide for Heavy Wall Pipe EXTERNALLY MOUNTED PORTABLE PIPE CUTTING AND BEVELING SYSTEM E.H. Wachs
More informationGovernment Recognized Export House OHSAS 18001:2007 ISO 14001:2004 PED Approved Company.
Government Recognized Export House OHSAS 800:200 ISO 400:2004 PED Approved Company. Phone : +9 22 44 (2 Lines) Fax : +9 22 289 4 Email : export@reliablepipes.com domestic@reliablepipes.com Designation:
More informationSIG-032-B TRAFFIC SIGNAL MAST ARM POLE AND MAST ARM DETAILS - CATEGORY III LUMINAIRE ARM (SEE CONTRACT) 6'-0", 8'-0", 10'-0" NOMINAL SPREAD
Michigan Department of Transportation 6'-0", 8'-0", 10'-0" NOMINAL SPREAD (SEE CONTRACT) LUMINAIRE ARM (SEE CONTRACT) POLE CAP 1'-6" (6'-0" ARM) 1'-10" (8'-0" ARM) 2'-0" (10'-0" ARM) NOMINAL RISE 2.38"
More informationTRAV-L-CUTTER Pipe Cutter
TRAV-L-CUTTER Pipe Cutter Horizontal and vertical c utting Fast and accurate cutting and beveling Add mounting chain sections to fit larger diameters COLD CUTTING, COMPACT DESIGN, EASY SET-UP The Wachs
More informationMSR/MSB Mechanical Setting Tool
Tech Unit No: 0620000004 Revision: B Approved By: Quality Engineer Date: 2014-12-16 MSR/MSB Mechanical Setting Tool FEATURES: Special designed Bow Spring provides positive control and allows one size Mechanical
More informationSUBMITTAL INFORMATION "BOLTS, NUTS AND FLAT WASHERS" "ABSTRACT OF ASTM A307 GRADE A AND B" CARBON STEEL BOLTS AND STUDS, 60,000 PSI TENSILE STRENGTH
"BOLTS, NUTS AND FLAT WASHERS" "ABSTRACT OF ASTM A307 GRADE A AND B" CARBON STEEL BOLTS AND STUDS, 60,000 PSI TENSILE STRENGTH GRADE: LOW CARBON STEEL GRADE A GRADE B PHOSPHOROUS MAX % 0.06 0.04 SULFUR,
More informationMetal Stamping Glossary
Metal Stamping Glossary Alloy - A substance that has metallic properties and is composed of two or more chemical elements of which at least one is an elemental metal. Annealing - A process involving the
More informationBOLTS AND NUTS Square Bolts( Table 1 ) Hex Nuts ( Table 7 ) Heavy Hex Nuts (Table 7) Heavy Hex Structural Bolts ( Table 2 )
BOLTS AND NUTS 1493 An externally threaded fastener that must be assembled with a nut to perform its intended service is a bolt. (Example: heavy hex structural bolt.) An externally threaded fastener that
More informationMotorized M3 AX7200 Rotary-Style Gasket Cutter Operating Instructions
Motorized M3 AX7200 Rotary-Style Gasket Cutter Operating Instructions INTRODUCTION Congratulations! You are the owner of the finest rotary-style gasket cutter in the world. Originally developed and patented
More informationStandard Specification for High-Strength Bolts for Structural Steel Joints [Metric] 1
Designation: A 325M 00 METRIC An American National Standard Standard Specification for High-Strength Bolts for Structural Steel Joints [Metric] 1 This standard is issued under the fixed designation A 325M;
More informationSIG-030-B TRAFFIC SIGNAL MAST ARM POLE AND MAST ARM DETAILS - CATEGORY I LUMINAIRE ARM 6'-0", 8'-0", 10'-0" NOMINAL SPREAD (SEE CONTRACT) POLE CAP
Michigan Department of Transportation 6'-0", 8'-0", 10'-0" NOMINAL SPREAD (SEE CONTRACT) LUMINAIRE ARM (SEE CONTRACT) POLE CAP 1'-6" (6'-0" ARM) 1'-10" (8'-0" ARM) 2'-0" (10'-0" ARM) NOMINAL RISE 2.38"
More informationMATERIAL COMBINATION NUMBER 2: Corrosive environment requiring harder, wear-resistant seating faces and resistance to dezincification.
Cast Iron Slide Gates Spec Sheet General The contractor shall furnish and install the following cast iron slide gate assemblies as listed on the Gate Schedule and detailed on the manufacturer s drawings.
More informationTR2000 Piping and Valve Materials under PED. The usage of this standard based on ASME B31.3
Memo 2010-12-01 (rev. 2) To Copy From Trælnes, Hege Subject TR2000 Piping and Valve Materials under PED. The usage of this standard based on ASME B31.3 1 Introduction and objective Reference is made to
More informationSECTION TRAFFIC SIGNAGE
SECTION 10 14 53 TRAFFIC SIGNAGE PART 1 - GENERAL 1.01 SECTION INCLUDES A. Furnishing and installing roadside traffic signage. B. Providing additional traffic signs as required in Sections 01 55 28 Controlling
More informationPRODUCT CATALOGUE. Major Features: Arc Bends Manufactured to: Pipestar now offering full-line of flanged Arcbends
PRODUCT CATALOGUE Pipestar now offering full-line of flanged Arcbends Pipestar offers a range of seamless long radius Arc HDPE sweep bends made to the highest quality standards. Pipestar offers a range
More informationISSUE MODIF. ORDER NO. WEEK ISSUE MODIF. ORDER NO. WEEK ISSUE MODIF. ORDER NO. WEEK 01 SME SME SME
1. Summary The still pipe used with Rosemount 5900 LPG/LNG antenna is not supplied by RTR, but is to be manufactured by the customer according to the RTR drawing D9240041-910 or D7000001-466. Additional
More informationSECTION THERAPEUTIC POOL ACCESSORIES
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 13 17 23.11 THERAPEUTIC POOL ACCESSORIES SPEC WRITER NOTES: Delete between // // if not applicable to project. Also, delete any other item or paragraph not applicable
More informationANSI B16.25 Fig. 1 - Maximum Envelope for Welding End Transitions
Fig. 1 - Maximum Envelope for Welding End Transitions Notes: 1 - Where transitions using maximum slope do not intersect inside or outside surface, as shown by phantom outlines, maximum slopes shown or
More informationWESTERN WIRE PRODUCTS
WESTERN WIRE PRODUCTS Celebra ng 100 years of Quality and Service 1914 2014 Thanks to our dedicated employees and customers we are celebra ng 100 years of being in business and we look forward to servicing
More informationMUELLER GAS. DH-5 Drilling Machine. For use on 1 1 /2 & 2 Line Stopper Fittings. Reliable Connections. General Information 2
operating Instructions manual MUELLER GAS TAble of contents PAGE DH-5 Drilling Machine For use on 1 1 /2 & 2 Line Stopper Fittings General Information 2 Installing and Stopping-off 1 1 /2 and 2 Line Stopper
More informationDrawing. Fig. 1 Drawing
Drawing Drawing is a metalworking process which uses tensile forces to stretch metal. It is broken up into two types: sheet metal drawing and wire, bar, and tube drawing. The specific definition for sheet
More informationSANDVIK 20C STRIP STEEL
SANDVIK 20C STRIP STEEL DATASHEET Sandvik 20C is a hardened and tempered carbon steel characterized by good properties in respect of: Fatigue strength and wear resistance Hardness combined with ductility
More informationProduct Information Report Nutserts
A B C A: Nutsert B: TSN (Thinsheet) Nutsert C: Large Flange Diamond Grip II ed Insert D: Standard Flange Diamond Grip II ed Insert E: Nutsert for Soft Materials D E Overview are inserts that, when installed,
More informationEvaluation of In-Pavement Light Fixture Designs and Performance
Evaluation of In-Pavement Light Fixture Designs and Performance Presented to: IES ALC Fall Technology Meeting By: Joseph Breen Date: Background In-Pavement Light Fixture Assemblies Utilize a Circle of
More informationOUR QUALITY POLICY VISION MISSION
AUSTENITE FASTENERS PVT.LTD. A unique name in fasteners line has come long way since its taking over Krishna Engineering Company which was established in 1999. The company has it is manufacturing plant
More informationGURANTEED TECHNICAL PARTICULARS OF BACK CLAMP FOR LT CROSS ARM
Technical Specification of Back Clamp for LT Cross Arm (MS) Back clamp for LT Cross Arm made out of 50 x 6mm MS Flat suitable for 8m X 300 Kg PSC poles. After fabrication the cross arm shall be painted
More informationPART MATERIALS. Section Fencing Materials. Description
PART 03000 - MATERIALS Section 03010 - Fencing Materials Description 03010.00 Scope - This section consists of the test requirements, specifications and tolerances for barbed wire, woven wire and chain
More information( This link will provide you with a list of all ISO-6983 G-Codes
CUSTOM HAZARDS CUSTOM HAZARDS CUSTOM HAZARDS In this lesson I am going to explain how to circle interpolate a 1/8-27 NPT with a formed thread E-Mill using G-Code on a vertical mill. I have provided the
More informationA Practical Update on Advanced Copper Alloys and On-Site Joining Methods for HVACR Systems. Educate Promote Defend Support Inspire
A Practical Update on Advanced Copper Alloys and On-Site Joining Methods for HVACR Systems A Practical Update on Advanced Copper Alloys and On-site Joining Methods for HVACR Systems Presented by: John
More informationFord Water Meter Couplings & Accessories
Section H 2/2001 Ford Water Meter Couplings & Accessories The Ford Meter Box Co., Inc. 775 Manchester Avenue, P.O. Box 443, Wabash, Indiana, USA 46992-0443 Telephone: 260/563-3171 FAX: 1-800-826-3487 Overseas
More informationTechnical Manual. ETP-CLASSIC incl type R. Content
Technical Manual ETP-CLASSIC incl type R Content Technical parts description...2 Mounting/dismantling tips...4 Design suggestions...7 Tolerances...13 Central bolt...15 Torsional stiffness...16 Screw pitch
More informationBalaji THE COMPANY MISSION
82, GANGOTRI INDUSTRIAL ESTATE, OPP. PANCHRATNA ESTATE, NR. RAMOL OVER BRIDGE, VATVA-382445.(GUJARAT), INDIA. Website : www.balajifasteners.co.in E-mail : info@balajifasteners.co.in OUR QUALITY POLICY
More informationUnit IV Drawing of rods, wires and tubes
Introduction Unit IV Drawing of rods, wires and tubes Drawing is a process in which the material is pulled through a die by means of a tensile force. Usually the constant cross section is circular (bar,
More informationGlobal Drilling Solutions, Inc
Wellhead Equipment - Casing Heads & Spools Casing Heads Top Connections All heads have standard API Flanges. Optional lockdown screws (two) for bowl protectors or (multiple) for annular seal compression
More informationStandard Specification for Carbon and Alloy Steel Nuts [Metric] 1
Designation: A 563M 04 METRIC Standard Specification for Carbon and Alloy Steel Nuts [Metric] 1 This standard is issued under the fixed designation A 563M; the number immediately following the designation
More informationINSTALLATION MANUAL IOWA MOLD TOOLING CO., INC. BOX 189, GARNER, IA MANUAL PART NUMBER:
PARTS-1 Model 24562/28562 Crane INSTALLATION MANUAL IOWA MOLD TOOLING CO., INC. BOX 189, GARNER, IA 50438-0189 641-923-3711 MANUAL PART NUMBER: 99903701 Iowa Mold Tooling Co., Inc. is an Oshkosh Truck
More informationSTEAM QUALITY TEST ELBOWS
STEAM QUALITY TEST ELBOWS V W Elbow Size V W 0.75-1.5 40mm 100mm 2 or larger 50mm 100mm Test Elbow Dimensions Nominal size Pipe outside diameter (inches/mm) Pipe wall thickness X Y A - Both ends B - All
More information