Step 1. Step 2. Step 3. Step 4. Painting Guide RF Reversible Terracotta Roof. RF Reversible Terracotta Roof Page 1 of 3. Side 1.

Transcription

1 RF Reversible Terracotta Roof Step 1 Step 2 Step 3 Lava Orange (GT002-LO) Step 4 Apply over the entire surface of the wooden areas with a #3 (Painting) brush. Be careful not to apply too much paint. Use a light hand (avoid painting into the deeper areas) to bring out the texture. Terracotta (GT002-TC) Dab a very small amount of Lava Orange onto a #12 () brush, then brush onto a paper towel to remove excess paint. With a feather light touch, apply over the entire surface of just the roof to bring out the mid tones in the terracotta shingles. Dab a very small amount of Terracotta onto a #12 () brush, then brush onto a paper towel to remove excess paint. With a feather light touch, apply the color over the entire surface of the roof to bring out the highlights. Let the paint dry before moving to the next RF Reversible Terracotta Roof Page 1 of 3 Deep Lava (GT002-DL) Apply Deep Lava over the surface of the roof with a #3 (Painting) brush. Be careful not to apply too much paint. Use a light hand (avoid painting into the deeper areas) to bring out the texture.

2 RF Reversible Terracotta Roof White Base Gray (12:1) Step 6 White (GT002-W) Shallow Water Seaweed Green (GT002-SG) Base Gray (GT002-BG) Apply Shallow Water Seaweed Green to the mossy areas on the roof using a #1 (Details) brush. Let the paint dry before moving to the next Pro Tip: If you wish to take it a step further, drybrush these areas with Moss Green. Step 7 Moss Green (GT002-MG) Base Gray (GT002-BG) Using a #3 (Painting) brush, apply Base Gray over the surface of the stones on side 2, avoiding the wood trim of the window. Use a light touch, leaving the deeper areas unpainted to preserve the depth and texture. Let the paint dry before moving to the next Step 8 Cardboard (GT002-CB) Apply Cardboard to random stones on the stone facing using either a #3 (Painting) or a #1 (Details) brush. This will add further texture and interest to the stones. Let the paint dry before moving to the next RF Reversible Terracotta Roof Page 2 of 3 Step 5 Dab a very small amount of a mix of White and Base Gray (mix at a ratio of 12:1) onto a #12 () brush, then brush onto a paper towel to remove excess paint. With a feather light touch, apply over the surface of the lower terracotta shingles near the bottom of the piece to create mid-tones. Let the paint dry before moving to the next

3 RF Reversible Terracotta Roof Stucco (GT002-ST) Step 10 Apply Stucco over the surface of the stucco using a #1 (Details) brush. Feel free to apply the paint into the indentations, since this area will have a wash to bring out the natural imperfections in the stucco. Or use a light touch, if you prefer, to add texture. Let the paint dry before moving to the next Dab a very small amount of mixed with a drop or two of onto a #12 () brush, then dab the brush onto a paper towel to remove excess paint. With a feather light touch, apply over the surface of the wood, to create highlights. Let the paint dry before moving to the next Step 11 * Dab a very small amount of onto a #12 () brush, then dab the brush onto a paper towel to remove excess paint. With a feather light touch, apply over the surface of the Stone facing, to create highlights. Let the paint dry before moving to the next Step 12 Black (GT002-B) Apply a light coat of Black (very diluted with water) to the entire surface of the stucco using a wet #12 () brush. Immediately and gently wipe off the excess paint with a paper towel, leaving some of the paint behind. You may decide to use an alternate weathering color such as or Earth Stone instead of Black. Let the paint dry. Pro Tip: If you prefer a lighter stucco, you can skip this RF Reversible Terracotta Roof Page 3 of 3 Step 9

4 WL Tudor Center Window Wall Step 1 Apply over the entire surface of the wooden beams using a #3 (Painting) brush. Use a light touch, leaving the deeper areas unpainted to show the texture of the wood. Let the paint dry before moving to the next Step 2 Dab a very small amount of Stone Edge mixed with a drop or two of onto a #12 () brush, then dab the brush onto a paper towel to remove excess paint. With a feather light touch, apply over the surface of the wood, to create highlights. Let the paint dry before moving to the next * Step 3 Stucco (GT002-ST) Apply Stucco over the surface of the stucco using a #3 (Painting) brush. Feel free to paint into the indentations, since this area will have a wash to bring out the natural imperfections in the stucco. Let the paint dry before moving to the next WL-002 Tudor Center Window Wall Page 1 of 2

5 WL Tudor Center Window Wall Step 4 Cardboard (GT002-CB) Apply Cardboard to the damaged areas of the stucco below the window using a #1 (Details) brush. Let the paint dry before moving to the next Step 5 Black (GT002-B) Apply a light coat of Black (very diluted with water) to the entire surface of the stucco using a wet #12 () brush. Immediately and gently wipe off the excess paint with a paper towel, leaving some of the paint behind. You may decide to use an alternate weathering color such as or Earth Stone instead of black. If you prefer a lighter stucco, you can skip this Note: Use the same approach for your other Tudor pieces shown here: Steep Stairs AC-001 Tudor Solid Wall WL-001 Tudor Overhang AC-019 Tudor Torch Wall WL-015 Tudor Double Corner Post PT-003 Tudor Offset Window Wall WL-014 Tudor Door Wall WL-003 Tudor Magnetic Wall WL-007 Tudor Post PT-001 WL-002 Tudor Center Window Wall Page 2 of 2

6 FL Wood Floor Step 2 Apply over the entire surface and edges of the piece with a #3 (Painting) brush. Be careful not to apply too much paint. Use a light hand (avoid painting into the deeper areas) to bring out the texture. Dab a very small amount of mixed with a drop or two of onto a #12 () brush, then dab the brush onto a paper towel to remove excess paint. With a feather light touch, apply over the surface of the wood, to create highlights. Let the paint dry before moving to the next Step 3 Golden Artist Colors Irridescent Silver * Using a #1 (Details) brush, apply Golden Artist Colors - Irridescent Silver to the tiny nail heads. If you prefer, substitute a metallic paint for this step, or skip it altogether. Pro Tip: You can also use a small rubber-tipped shaping tool for greater precision. Shown below: Find a Golden Artist Colors store near you at FL Wood Floor Page 1 of 2 Step 1

7 FL Wood Floor Note: Use the same approach for your other wooden pieces shown here: Tudor Half Height Corner Post PT-004 Assassin s Perch AC-004 Wood Stairwell Floor FL-003 Interior Railing AC-008 Closed Shutters Window Insert AC-006 Magnetic Hanging Sign AC-027 Magnetic Inn Sign AC-026 Wood Trapdoor Floor FL-005 Ladder AC-007 Open Shutters Window Insert AC-020 Tudor Double Door Wall WL-012 Crate and Barrel AC-039 Water Barrel AC-041 Curved Bar Segment AC-031 Stool AC-035 Ale Kegs AC-036 Long Bar Segment AC-030 Short Bar Segment AC-032 FL Wood Floor Page 2 of 2 Balcony AC-005