Assembly Instructions for Summit Motel Kits # SMFS and SMBD

Size: px

Start display at page:

Download "Assembly Instructions for Summit Motel Kits # SMFS and SMBD"

Roderick Houston
5 years ago
Views:

1 Assembly Instructions for Summit Motel Kits # SMFS and SMBD Introduction Thank you for your purchase of the Summit Motel. This modern motel can be converted to almost any chain motel of your choice, depending on the colors you paint it. Because of copyright laws we cannot supply the logos, but you can copy them from the Internet on the motel's homepage and print them. Summit Motel signs are supplied with this kit. This motel comes in to 2 versions: SMFS - the full size version with 2 wings and SMBD - the backdrop version with only the main building, tower and the entrance awning. Before you begin: This kit is milled in styrene plastic and is very easy to glue together using Plastdruct Plastic Weld or similar glue products. Please take your time to identify all parts, lay them out, clean them for any sprues and read these instructions before you start putting them together. Parts overview (not to scale) 1. Front wall, 1 pc. 2. SMFS: Middle walls, 2 pcs. SMBD: Rear wall, 1 pc. 3. SMFS: Rear wall, 1 pc. All pcs. 1mm / 0,04" 4 & 5. End walls for main building, one of each 1mm / 0,04"

2 6 & 7. End walls of rear wing, one of each - SMFS only 1mm / 0,04" 8, 9, 10 & 11. Roof parts for SMFS version, 1,5mm / 0,06" 12, 13 & 14 15, 16, 17 & 18. Roof parts for SMBD version, 1,5mm / 0,06" 19. Glass for end-wall window, 1 pc. In SMBD, 3 pcs. in SMFS pc. glass for entry door and end-wall door 21. SMBD: 1 glass strip for 2. floor windows 22. SMFS: 2 extra glass strips for rear wing windows glass strips for 1. floor windows in main building 24. Room window, 0.5mm / 0.02", SMFS: 30 pcs, SMBD: 14 pcs. 25. Hallway window (end wall), 0.5mm / 0.02", SMFS: 3 pcs. SMBD 1 pc.

3 26. Entrance door 27. End-wall door, SMFS 2 pcs., SMBD 1 pc. 28. End-wall door and backing plate, SMFS only 29. Airconditioner, 2mm / 0,08", SMFS: 32 pcs. SMBD: 15 pcs. Roof supports, 1mm / 0,04": 30. End support, SMFS: 3 pcs. SMBD: 2 pcs. 31. Diagonal end support, SMFS: 6 pcs. SMBD: 4 pcs. 32. Middle cross support, SMFS: 3 pcs. SMBD: 1 pc. 33. End cross support, SMFS: 3 pcs. SMBD: 2 pcs. Tower: 34. Front/rear wall, 2 pcs. 35. Side-wall, 2 pcs. 36. Roof, 2 pcs Tower trim pieces, 0.5mm / 0.02" 37. Front top trim, 2 pcs. 38. Side top trim, 2 pcs. 39. Front corner strips, 2. pcs 40. Side corner strips, 4 pcs. 41. Rear corner strips, 2 pcs.

4 Entrance awning, 1mm / 0,04": 42. Side inner cross beams, 2 pcs. 43. Rear inner cross beam 44. Front inner cross beam 45. Awning roof board, 2 pcs. 1,5mm / 0,06" parts: 46. Side outer cross beam 47. Front outer cross beam 47. Rear outer cross beam 46. Side outer cross beam 4 sets of 3 column pieces, 2+1mm / " 48. A 49. B 50. C A B C 5 awning trim pieces, 0.5mm / 0.02" 51. Front decoration 52. Front top trim 53. Side top trim, 2 pcs. 54. Base, SMFS 2 pcs. SMBD 1 pc x 0.20 x 2 strips for corner support, SMFS 8 pcs., SMBD 4 pcs x 0.04 x 3.15 strips for awning roof, 2 pcs. 57. Sign base for tower, 4 pcs. 58. Sign base for awning, 1 pc.

Tools: AC mounting tool Assembly Before painting, we recommend that you assemble the sides and roof, the tower, the awning, and mount the air conditioners.

5 Tools: AC mounting tool Assembly Before painting, we recommend that you assemble the sides and roof, the tower, the awning, and mount the air conditioners. Paint the walls, the window and door frames before installing the windows and doors in the wall. (see painting section) Mounting airconditioners The easiest way to install the airconditioners (29) is to mount them on the walls before assembling walls. The windows on each side of the entrance door do not have AC's. Use the AC mounting tool. Place the tool in the window opening and slide the AC into the slot, gluing it to the wall. Entrance awning Identify 4 sets of these 3 column parts. Glue them together in 2 sets of the 2 patterns shown as top view: A B C

Mount the side inner cross beam (42) in the short slots of the columns and

the columns Mount the front and rear outer cross beams (47) so the bottom

Mount the 2 roof pieces (45) Mount the 2 roof strips (56) in the open spaces

6 Mount the side inner cross beam (42) in the short slots of the columns and mount the front and rear inner cross beams (43 & 44) in the long slots of the columns. Mount the side outer cross beams (46) so the top edges align with the top of the columns Mount the front and rear outer cross beams (47) so the bottom edges align with the bottom edges of the side beams. Mount the 2 roof pieces (45) Mount the 2 roof strips (56) in the open spaces along the side. Mount the front and side top trim pieces (52 & 53) along the top edges of the outer cross beams. Mount the front decoration pieces (51) as shown in the picture.

Apply the paper tape as tar paper roofing on the awning Main

Mount the rear wall (2) in the same way.

the end cross supports (33) Glue the end support assembly

7 Apply the paper tape as tar paper roofing on the awning Main building Mount the end walls (4 & 5) on the inside of the front wall (1). Use the 0.12 x 0.20 strips (55) as a corner support. Mount the rear wall (2) in the same way. Roof & supports Glue the end supports (30) into the slots in the end cross supports (33) Glue the end support assembly onto the wall frame in both ends as shown in the picture. Glue the diagonal end supports (31) from corner to middle as shown in the picture

Glue the middle cross support (32) onto the wall frame in the middle. Rear wing (SMFS only) Assemble the side walls (2 & 3) and end walls (6 & 7) in the same way as the main building.

SMBD version: Glue the roof pieces (15, 16, 17, 18) onto the roof supports. The cut in the one end piece is where the tower goes.

8 Glue the middle cross support (32) onto the wall frame in the middle. Rear wing (SMFS only) Assemble the side walls (2 & 3) and end walls (6 & 7) in the same way as the main building. Glue the end roof support assembly onto the wall frame in the one end and glue the 2 middle cross supports (29) evenly spaced onto the wall frame. SMBD version: Glue the roof pieces (15, 16, 17, 18) onto the roof supports. The cut in the one end piece is where the tower goes. SMFS version: Glue the roof pieces (8, 9, 10, 11) onto the main building roof supports. The cut in the one end piece is where the tower goes and the cut in the rear piece is where the rear wing goes. Glue the roof pieces (12, 13, 14) onto the rear wing roof supports Tower Glue the side walls (35) to the inside of the front & rear walls (34). Glue the roof (36) on. Glue the front top trim (37) and side top trim (38) onto the edges of the front and side walls.

Glue the side corner strips (40) along the edges of the side, the narrower legs flush with the edge. Glue the front corner strips (39) along the edges of the front, flush with the side corner trim.

On the model you can use them as paint lines. Airbrushing gives the best result, but of course you can brush paint it instead.

Painting the trim on the entrance awning and tower: When the base color has dried, brush paint the trim very carefully with a different color.

9 Glue the side corner strips (40) along the edges of the side, the narrower legs flush with the edge. Glue the front corner strips (39) along the edges of the front, flush with the side corner trim. Glue the short rear corner strips (41) along the edges of the rear, flush with the side corner trim. Painting The grooves on the side walls indicate where the concrete changes color on the prototype. On the model you can use them as paint lines. Airbrushing gives the best result, but of course you can brush paint it instead. When the base color has dried, mask off and paint the lower wall, the middle stripe and the top stripe with a different color. Painting the trim on the entrance awning and tower: When the base color has dried, brush paint the trim very carefully with a different color. Paint the tar paper roof of the awning flat black or grey. Paint the windows (24 & 25) and doors (26 & 27). Most motels have either black, white, or aluminum window frames and doors. As mentioned earlier, this motel can be converted to almost any chain motel of your choice, depending on the colors you paint it. The colors used on the cover version is Floquil 50/50 Antique white and White for the base color and Floquill Earth for the dark accent color. Mounting windows & doors Glue on the clear window strips (21, 22 & 23) and the door glass (20) inside the wall as shown.

After the glue has set on the window glazing, press fit the window frames into the opening. Your fingers and nails should be the only tools you need.

Roofing Install the roof shingles as described in the instructions enclosed with the shingle strips.

Peel off the backing paper and mount it on the sign bases (57 & 58).

Final installation To keep the walls straight you should mount the base plate inside the walls at the bottom.

10 After the glue has set on the window glazing, press fit the window frames into the opening. Your fingers and nails should be the only tools you need. You may use the tip of a knife or another point instrument to press in the corners. Roofing Install the roof shingles as described in the instructions enclosed with the shingle strips. Signs If you want to use the self-adhesive "Summit Motel" signs included, cut them out with a knife or a pair of scissors along the black edge. Peel off the backing paper and mount it on the sign bases (57 & 58). Carefully touch up the edges with black paint before gluing then on the tower and awning sides as shown in the pictures. Final installation To keep the walls straight you should mount the base plate inside the walls at the bottom. Or even better, glue the base plate to the lot on your layout and place the building over it without gluing. This way you can always get to the inside for later installation of interior, curtains or light. Curtains (not included) For curtains I have used strips of Evergreen 4528 Metal siding which looks like the curtains on my prototype, but curtain design vary from one motel to another. Another way of blocking the view into the building is to mount dark tinted window film on the inside of the glazing strips. Versions:

CVS Pharmacy kit in HO scale

CVS Pharmacy kit in HO scale Parking lot base and cars not included This kit includes all building parts and wall-mounted signs milled in white styrene plastic, clear window glazing and pre-cut Plastruct