OCA-RFI/C Appendix C

Transcription

1 ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE 1 CLASS A / IKE JACKET - UNISEX FITTING Fechheimer or equivalent CHP SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC / REQUIRED DOCUMENTATION: Vendor must provide documentation that the garment s fabric meets the specifications listed below. Acceptable documents are manufacturer s fabric brochure or signed letter in manufacturer s letterhead indicating compliance. Compliance documents must be submitted clearly identifying the Proposal Number, Item number and Item Description. MATERIAL WEIGHT oz/linear yd CONTENT 55% poly/45% wool STRENGHT 210 lbs warp, 135 lbs filling COLOR #168-Forest Green WEAVE Elastique CONSTRUCTION 125 ends/inch by 85 picks/inch Enter comments in this column for each item: BASIC DESIGN Jacket should be Eisenhower style, waist length or 21 3/4 " on a size 40, shall have semi-peak lapels and a zipper front. The inside of the jacket shall contain shoulder pads, sleeve heads, chest piece inner front, armhole tape and cuff inner lined. The entire body and sleeve shall be fully lined. BODY DETAIL Front will be plain with box pleated patch pockets, flaps, shoulder straps and badge tab. Inside facing of jacket must be the same as the outer fabric. There shall be a first quality zipper down the front. The back will be seamed (2 piece back) bi-swing, ends of each bi-swing held in place with a strip of elastic. There will be a separate waistband cut in two pieces and the waistband will be 2 ½ " wide, and shirred on each side over hip. Page 1 of 59

2 ZIPPER The jacket shall close with a first quality brass separating zipper, installed at the bottom of the jacket, vertically to the base of the lapels. The zipper tape shall be black. COLLAR Collar points, plastic stays, collar rear FRONT Buttons, button spacing, placket EPAULETS Epaulets shall be made of the same fabric as the jacket and shall be sewn into the sleeve seam, cross-stitched, and the end of the epaulet tacked to the jacket at the neck BADGE TAB Badge tab shall be made of the outer fabric, be 3/4 " wide with 2 eyelets spaced vertically 1" apart ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE 2 SPECTRUM ULTIMATE FOUL WEATHER JACKET (GORE-TEX) Fechheimer or equivalent SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC / REQUIRED DOCUMENTATION: Vendor must provide documentation that the garment s fabric meets the specifications listed below. Acceptable documents are official manufacturer s fabric brochure or signed letter in manufacturer s letterhead indicating compliance. Compliance documents must be submitted clearly identifying the Proposal Number, Item number and Item Description. MATERIAL WEIGHT 3.6 oz/sq. yd. CONTENT Supplex supreme-warp: 70 Denier Nylon Filling: 3 ply 70 Denier Nylon. STRENGHT 200 lbs warp, 150 lbs filling Page 2 of 59

3 TEAR STRENGHT 9.0 lbs warp, 8.0 lbs filling ABRASION 4LB Diaphram, 1lb. Head load:300 COLOR Black WEAVE Plain LINING Gore-Tex material, waterproof, breathable lining or other porous fluoropolymer membrane (Teflon) coating that is free hanging. This membrane had about 9 billion pores per square inch (around 1.4 billion pores per square centimeter). Each pore is approximately 1/20,000 the size of a water droplet, making it impenetrable to liquid water while still allowing the more autonomous water vapor molecules to pass through. Moisture vapor, Transmission rate (g/m2/24hr), Procedure B procedure BW Hydrostatic Resistance (psi), water permeability Initial After Cold Flex warp, fill After 100 hours of continuous Wet Flex (agitation) After Dry cleaning After Synthetic perspiration After sustained Pressure After exposure to contamination ANY LEAKAGE IS UNACCEPTABLE AND GARMENT WILL BE RETURNED TO SUPPLIER BASIC DESIGN Waist length, single breasted, black Gore-Tex LTD breathable waterproof lining, or other porous fluoropolymer membrane (Teflon) coating that is free hanging. This membrane had about 9 billion pores per square inch (around 1.4 billion pores per square centimeter). Each pore is approximately 1/20,000 the size of a water droplet, making it impenetrable to liquid water while still allowing the more autonomous water vapor molecules to pass through.removable, Thinsulate body/sleeve liner, and front zipper storm front closure, bi-swing back, raglan sleeves, sleeve zippers, pocket flaps, inverted pleated patch pockets with hand warmer openings, collar, knit wind collar, shoulder straps, badge tab, zippered side vents with tab INSULATION 3M Thinsulate, with a scrim covering front and back to prevent migration of insulation fibers. Lining must be quilted horizontally with a min of a 6 railroad pattern for max. thermo retention. Excess stitching and openings in liner cause extreme loss of body heat. Page 3 of 59

4 REMOVABLE LINER A zip-out insulated liner that incorporates CDS-200 Thinsulate Thermal Insulation in the body portion of the liner and CDS-100 Thinsulate Thermal Insulation in the sleeves. The insulation shall be quilted to black 86 pick nylon on the face side of the liner and nylon tricot on the backing. There shall be black knit inserts placed under the arm of the liner sleeves 9 length and 3 ½ at widest center point for comfort and ease of movement. The liner will attach to the jacket with a grip-lock non-run zipper. SHELL FOR REMOVABLE LINER Content: 86 pick, 100% Nylon Taffeta, weave-plain, Denier: warp-70 Fill-70 Material wt: 1.8 oz. /sq. yd. Color: Black BODY DETAIL 3M Thinsulate CDS 200 composed of 65% Polyolefin microfibers and 35% 6 Denier Polyester staple fibers, weigh 200grs/sq. m. horizontally quilted. SLEEVES 3M Thinsulate CDS 100 Content: 65% Polyolefin microfibers 35% 6 Denier Polyester staple fibers Material wt: 100grs/sq.m. Liner: The perimeter of the liner shall be bound with black nylon taffeta tape and the liner shall have a black vislon zipper track to allow the liner to zip out of the jacket. The liner sleeves will have a female snap by the in sleeve seam no more than 1 from the end of the sleeve. The liner have a left breast patch pocket, each sleeve hem must be finished with bias tape so there are no raw edges. The liner shall be designed with vents corresponding with the zippered side vents on the jacket to allow easy access to weapon or equipment. Tab: Attached to the jacket sleeve, made of shell material with a make snap, the tab and snap are used to secure the liner sleeves. COLLAR Collar points: Well shaped and symmetrical. The front storm flap shall extend to the top of the collar Collar interlining: Collar and collar interlining must be cut on bias. Under collar: Be constructed to conceal a removable Gore-Tex Hood Knit Wind Collar: A knit wind collar of 1x1 ribbed spun nylon sewn into the collar seam measuring 14 long by 1½ wide at the center BACK One piece back with a bi-swing Bi-swing: 9 in length and 1 ½ in depth. It shall be constructed with an elasticized anchor so the bi-swing will snap back into proper position after being extended. It shall be constructed with an elasticized anchor made of a 2 wide strip of Lycra so the bi-swing will snap back into proper position after being extended INTERLINING To be used in collar, pocket flaps, shoulder straps, front waistband, and storm front. Material: 100% Cotton Osnaburg DEF: Osnaburg was a coarse type of plain textile fabric, named for the city of Osnabrück (from which it may Page 4 of 59

5 have been first imported into English-speaking countries). Originally made from flax yarns, it has been made from either flax, tow or jute yarns, sometimes flax or tow warp with mixed or jute weft, and often entirely of jute. The finer and better qualities form a kind of common sheeting, and the various kinds may contain from 20 to 36 threads per inch and 10 to 15 picks per inch. Material wt: 3.45 yds./lb POCKETS 7 ½ wide and 8 depth, there shall be an inverted pleated patch pocket on each front of the jacket. On the side of the pocket: Pockets shall be constructed with hand warmer openings Top part of the pocket: Will be black Kasha, the top and bottom of the side openings shall be securely bartacked. Patch pocket: Will have an opening at the top underneath the flaps, the top of each patch pocket must be bound with black nylon binding, back of box pleated patch pocket must be fully lined. The Left front Pocket: Will have a pencil compartment opening on the inside corner of the pocket flap, the opening will be reinforced by bartacks. Pocket flaps: Have a metal snap closure system, the male portion of the snaps shall be located on the underside of each flap and the female portion of the snaps shall be in a corresponding location on the breast pocket. Each flap shall have a dummy buttonhole with a 24 ligne metal button on the top of the flap attached with a kotter key on the bottom side of the flap Inside left breast pocket: Min width of 6 and min depth of 8 ¼, the inside pocket will incorporate a zipper closure system utilizing a 6 CFC-256B2 zipper that is made with bottom stops at both ends. ELASTIC WAISTBAND Separate waistband shall be elasticized in the back. Spacing: 2 rows of stitching each ½ apart, centered on the waistband, and extending through the elastic. Elastic: Shall be securely tacked at each end Zipper: Be sewn into each side for access. Elasticized tabs: Be sewn into the waistband for closure of the side tab Belt keeper tab: 2 belt keeper tabs, with sewn eyelets, made of shell fabric and located 2 from back zipper side vents SLEEVES 3 pieces, raglan style sleeves with cuffs. The top half of the cuff must be elasticized and the bottom half to close with a tab and double snap for cuff adjustment. The sleeves shall be constructed with 7 zippers on the underseams. The attachment without puncturing the Gore-Tex or other porous fluoropolymer membrane (Teflon) coating that is free hanging to a fabric. This membrane had about 9 billion pores per square inch (around 1.4 billion pores per square centimeter). Each pore is approximately 1/20,000 the size of a water droplet, making it impenetrable to liquid water while still allowing the more autonomous water vapor molecules to pass through.by allowing access to the shell is permitted. COLLAR 2 plies of the shell fabric plus the interlining Ply: all plies to be cut on bias Interlining: Be sewn to the undercollar Collar point: Shall be well shaped and symmetrical Page 5 of 59

6 Under collar: To be constructed to conceal a removable Gore-Tex Hood or other porous fluoropolymer membrane (Teflon) coating that is bonded to a fabric. This membrane had about 9 billion pores per square inch (around 1.4 billion pores per square centimeter). Each pore is approximately 1/20,000 the size of a water droplet, making it impenetrable to liquid water while still allowing the more autonomous water vapor molecules to pass through. EPAULETS Measuring 2 ½ at the widest point and tapering to 13/4 at the narrow end, fastened with a 24 ligne metal uniform button and buttonhole, shoulder strap to be cross-stitched and sewn down. STORM FLAP There shall be a double front storm flap Top storm flap: 2 ¾ wide and will extend from the bottom of the waistband to the top of the collar point Metal snaps: There shall be 6 black gun metal snaps centered down the top storm flap Under storm flap: 2 wide and will extend from the bottom of the waistband to the top of the collar point Male portion of the snaps: Shall be positioned on the under storm flap to correspond to the placement of the snaps on the top storm flap to provide a neat and secure closure Center of snap: To be plugged, concealing open portion of snap SIDE VENTS The jacket shall be designed with side vents to allow for easy access to equipment The vent: Shall incorporate 10 zippers Bottom of each vent: There shall be an elasticized tab and snap closure system to prevent gaping between the front and rear portion of the jacket when the side zipper are in the full upward position WEEP EYELETS To have black metal 1/8 weep eyelets located at the bottom of sleeve (both panels) and front and back body panels. BADGE TAB To be made of self material with 2 metal eyelets The bottom of the badge tab: Shall be 2 ¼ 2 ½ above the left pocket flap FRONT ZIPPER The front zipper opening shall be accomplished with a two way pull, heavy-duty # 5 nylon modeled zipper, and extend from bottom of waistband to collar seam. KNIT WIND COLLAR Knit wind collar: 1x1 ribbed spun nylon sewn into the collar seam Collar seam: Measuring 14 long (for size Large) by 1 ½ wide at the center SEAM WATERPROOFING Seams shall be taped with 7/8 two layer Gore tape or other porous fluoropolymer tape (Teflon) seam tape. There shall be no stitching through the LTD liner except those seams that are waterproofed. There will be metal eyelets on the sleeve bottoms and above the front and back waistband, for water drainage in laundering Page 6 of 59

7 ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE 3 PROLINE MID LENGTH RAINCOAT AND HOOD Fechheimer or equivalent Coat with 7150 Hood FABRIC 100% Polyester SPECIFICATIONS AND ESSENTIAL FEATURES MATERIAL WEIGHT 4.6 oz/sq. yd. CONTENT Deniers: warp 2*150D Weft 2*150D CONTEXTURE Warp: 53 Weft: 45 CONSTRUCTION Plain Weave COLOR Black MEMBRANE Waterproof & breathable Polyurethane membrane. Coated fabrics are cause for rejection. Color: white BACK KNIT Tricot Color: High visibility yellow Page 7 of 59

8 3-PLY LAMINATE Material wt.: 6.9 oz. /sq. yd. Tensile strength: warp > 1150N, Weft >1000N Tear Strength: warp>90n, Weft>90N BASIC STYLING Shall be a rain jacket with raglan style sleeves, shall be reversible with one side black and one side high-visibility florescent yellow, shall include: convertible collar with Velcro closure, 2 side openings with Velcro closure, snap front with double closure, Velcro cuff closure. SLEEVES Shall be 1-piece Style: Raglan Sleeves hems: ¾ wide Tab: Attached at the inside seam made of face fabric, measuring 2 wide at the base and 1 ½ in length Strip of Velcro: 2 by 1 strip of Velcro on the backside of the tab, will be in line with a 6 by 1 strip of Velcro attached to the sleeve Long strip of Velcro: 1 from edge of sleeve and begin 1 ¼ from side seam and extend around the front of the sleeve, allow adjustable sleeve closure Snap: Set 2 from the side seam the backs of the snaps shall show on the dark side of the jacket, allow for closure of the sleeve on the high visibility side. COLLAR: Shall be made of 2 plies of face fabric Collar points: 3 ½ wide, 4 across Tab: Made of 2 plies of face fabric set into the collar seam at the front edge/neck seam and measuring 3 on top, 2½ on the bottom and ¾ wide. It shall have Velcro on both sides measuring 1 ¼ by ¾ Tab: Made of 2 plies of face fabric set into the collar seam at the front edge/neck seam and measuring 3 on top, 2½ on the bottom and ¾ wide. It shall have Velcro on both sides measuring 1 ¼ by ¾ Underside of the collar: A 1 x ¾ piece of Velcro on it to fasten the tab when not in use. Both sides of collar: 2 x ¾ strips of Velcro attached to provide adjustable neck closure when worn on either side Well shaped and symmetrical SIDE VENTS Jacket shall be designed with side vents for easy access to equipment Vents: Measure 11 and shall be set into side seams of jacket and shall be covered by welts extending out 1 ¼ Closure for the side vents: Provided by a 4 ½ by ¾ strip of Velcro centered on insides of the vent/welt FRONT Buttons: 5 snap front closure Button spacing: The top snap shall be 1 from the top of the flap, the other snaps shall be equally spaced down the front. DARK SIDE The left front: Have a double male snap The right front: Have 2 flaps measuring 2 ½ wide and will sandwich the left flap with 2 female snaps Page 8 of 59

9 Placket: Placket front shall be constructed on the dark side of the jacket SEAM STITCHING Shoulder, underarm, and side seams shall be double needle chain stitch, all other seams to be single needle construction WATERPROOFING All seams to be waterproofed with waterproofing tape of same manufacturing origin as body goods-waterproof, breathable, membrane. REFLECTIVE TAPE 1 ½ 3m Silver reflective tape applied to the high visibility side, a stripe around each sleeve at the edge and around front and black under the armhole. HOOD Snap-on hood Fechheimer or equivalent Style: # 7150 Materials: same as jacket Color: black PRODUCT SIZING The Product shall be manufactured and readily available in the following sizes: (Per table below) STOCK SIZES: XS 3XL (REGULAR) M-3XL (LONG) MEASUREMENTS: Size XS S M L XL 2XL 3XL Chest: Sweep: Sleeve Length size M: REG=20 LONG=21 (+/-.75 inches) Page 9 of 59

10 ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE 4 PROLINE RAIN PANTS Fechheimer or equivalent 78240ZP FABRIC 100% Polyester MATERIAL WEIGHT 4.6 oz/sq. yd. CONSTRUCTION Plain Weave COLOR Black SPECIFICATIONS AND ESSENTIAL FEATURES MEMBRANE Waterproof & breathable Polyurethane membrane. Poly urethane coating is a cause for rejection. BACK KNIT Tricot Color: High visibility yellow 3-PLY LAMINATE Material wt.: 6.9 oz. /sq. yd. Tensile strength: warp > 1150N, Weft >1000N Tear Strength: warp>90n, Weft>90N BASIC STYLING Slip over Rain Pants, shell to be Proline Fabric, full cut style with elasticized back waistband and adjustable snap closure at waist and legs. Page 10 of 59

11 WAISTBAND Elasticized Vent: A 7 ½ vent on each side seam with snap closure Waist adjustability: On each side seam Female snap: on the front portion of the waistband 2 male snaps: On the back portion of the waistband, they shall be placed 1 apart. LEGS Design: Straight leg Side leg bottom shall have an 18 ½ zipper closure. Zipper shall be concealed with a 1 ¼ storm flap on black facing and hi-visibility side. There shall be a snap adjustment tab at ankle inseam. Snaps are spaced 3 1/2 apart. WATERPROOFING All seams to be waterproofed with waterproofing tape of same color and manufacturing origin as high visibility goodswaterproof, breathable, membrane. PRODUCT SIZING The Product shall be manufactured and readily available in the following sizes: (Per table below) SIZING: Length XS S M L XL 2XL 3XL 4XL 5XL SHORT X X X X REG X X X X X X X X X ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE 5 MALE TROUSERS Fechheimer or equivalent SPECIFICATIONS AND ESSENTIAL FEATURES Page 11 of 59

12 FABRIC / REQUIRED DOCUMENTATION: Vendor must provide documentation that the garment s fabric meets the specifications listed below. Acceptable documents are official manufacturer s fabric brochure or signed letter in manufacturer s letterhead indicating compliance. Compliance documents must be submitted clearly identifying the Proposal Number, Item number and Item Description. MATERIAL WEIGHT 16 ½ - 17 oz/linear yd. (oz width) CONTENT 55% Dacron/ 45% Wool FILLING CONSTRUCTION 125 ends/inch 85 picks/inch BREAKING STRENGTH 210 lbs warp lbs COLOR Forest Green #168 DESIGN Trouser shall be manufactured from a men s uniform trouser pattern, the styling shall incorporate a plain front, 2 straight side front pockets, and 2 hip pockets, trouser to be straight leg style. POCKETING Material: 70% Polyester/ 30% cotton Material wt.: 2.9 oz. /sq. yd. (60 width) Minimum warp 78 and fill 64 count Must have a durable press finish Color: Black Page 12 of 59

13 POCKET DESIGN SIDE POCKET: Min. opening of 6 ½ and a min. depth of 5 ¾ measured from the bottom of the pocket opening Pocket opening: shall have firm straight bartacks at the top and bottom Pockets: Shall be constructed using the stitch, turn, and topstitch method Pocket facing: Made of the basic fabric and measure a min. of 1 ½ from the bottom of the pocket opening HIP POCKETS: Shall have min. opening of 6 and a min. depth of 7 ½ measured from the bottom of the pocket opening. Shall be constructed using the double welt method on a REECE PW Machine and the welts shall finished in such a manner that there is no topstitching. The corner of hip pockets openings: Shall have firm straight bartacks for reinforcement The corners of the hip pockets: Shall have triangle bartacks for reinforcing strength The left hip pocket: Will have a button and buttonhole, no tab CLUB POCKET: Located 2 ½ below each hip pocket. It shall be ½ from the side seam with a min. opening of 3 ¼ and a min. depth of 8. Material: To be the same as side and hip pockets. Club pockets shall be constructed using the double welt method on a REECE PW machine and finished in such a manner that there is no topstitching The corners of the club pockets: Shall have triangle bartacks for reinforcing strength WATCH POCKET: Shall be located on the right front at the waistband Front of the pocket: Shall be made of pocketing fabric Back of the pocket: Shall be made of basic fabric and 2 pieces are securely stitched together Each corner of the pocket opening: Shall have firm straight bartacks WAISTBAND Shall be constructed using the closed method and shall measure a min. of 2 wide. Content: Must contain ¾ inch Ban-Rol or other monofilament stabilizer to prevent roll over at the trouser front. Waistband closure: Shall be accomplished with a single crush proof hook and eye centered on the waistband for wearer comfort Hook and eye: Shall be reinforced with 7/8 inch non-woven stay tape that is anchored with topstitching through and through to the top of the waistband. The waistband must also be topstitched below the waistband seam through the waistband curtain for added strength. The back center seam of the trouser: To be finished to allow for alterations The outlet in the seat: Is to be in proportion to waist outlet so seat may also be let out. Seat seam: Must be sewn with a tandem needle machine (double needle stitch) for maximum strength WAISTBAND CURTAIN Shall finish a min. 2-1/8 wide and is to be made of the same fabric and color as the pocketing material and shall be attached to the top of the trouser with a zigzag stitch Material: Wet laid non woven canvas Material wt.: 3.3 oz. /sq. yd. Color: The same color and material as the pocketing The ½ rubberized surface areas is positioned 1 ¼ up from the bottom of the curtain. Page 13 of 59

14 RUBBERIZED TRU-GRIP, a ½ surface area composed of thin gauge rubber for max. Comfort and performance. Substitution of silicone strip or strips in place of Tru-Grip shall not be acceptable. CURTAIN Content: 59% Polyester/ 41% Rubber Count: yarns/ inch Width: 1 1 1/8 inch Warp: 300 Denier Texturized Polyester Filling: 300 Denier Texturized Polyester Rubber: 55 Gauge FLY Zipper: Metal memory lock zipper French fly tab: On the inside of the right fly, the tab shall be double ply made of the basic cloth The right fly: Shall be lined with the same fabric as the waistband curtain and pocketing The fly lining: Shall be sewn to the left fly below the zipper in a neat and durable manner Button: Shall be located on the left fly corresponding with the French Fly tab to provide a clean and comfortable closure Tabs made of pocketing material or a grown on French Fly will be cause for rejection At the bottom of the fly: Shall be a firm straight bartack going through the zipper tape The crotch: Shall be lined in front BELT LOOPS Min. of 7 belt loops Style: Keystone style At the top: Measure 1 ¾ in width At the bottom: 1 ¼ in width The center back loop: ¾ wide straight loop The keystone loops: Shall be sewn into the bottom of the waistband and the top of the loops shall be caught into the waistband curtain seam with a Rocap machine The bottom of the center back loop: Shall be tacked to the trouser The top of the loop: Tacked to the outside of the waistband ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE 6 FEMALE TROUSERS Fechheimer or equivalent SPECIFICATIONS AND ESSENTIAL FEATURES Page 14 of 59

15 FABRIC / REQUIRED DOCUMENTATION: Vendor must provide documentation that garment s fabric meets the specifications listed below. Acceptable documents are official manufacturer s fabric brochure or signed letter in company letterhead indicating compliance. Compliance documents must be submitted clearly identifying the Proposal Number, Item number and Item Description. MATERIAL WEIGHT 16 ½ - 17 oz/linear yd. (60 width) CONTENT 55% Dacron/ 45% Wool FILLING CONSTRUCTION 125 ends/inch 85 picks/inch BREAKING STRENGTH 210 lbs warp lbs COLOR Forest Green #168 DESIGN Slack shall be straight leg design, incorporate 2 straight side pockets, 2 hip pockets and 2 rear billy pockets. Front: Shall be manufactured from a women s uniform trouser pattern with a plain front Rear: One dart on each rear panel above the hip pockets POCKETING Material: 70% Polyester/ 30% cotton Material wt.: 2.9 oz. /sq. yd. (60 width) Must have a durable press finish Min: 78 warp by 64 fill count Color: Black POCKET DESIGN SIDE POCKET: Min. opening of 6 ½ and a min. depth of 5 ¾ measured from the bottom of the pocket opening Pocket opening: shall have firm straight bartacks at the top and bottom Pockets: Shall be constructed using the stitch, turn, and topstitch method Page 15 of 59

16 Pocket facing: Made of the basic fabric and measure a min. of 1 ½ from the bottom of the pocket opening HIP POCKETS: Shall have min. opening of 6 and a min. depth of 7 ½ measured from the bottom of the pocket opening. Shall be constructed using the double welt method on a REECE PW Machine and the welts shall finished in such a manner that there is no topstitching. The corner of hip pockets openings: Shall have firm straight bartacks for reinforcement The corners of the hip pockets: Shall have triangle bartacks for reinforcing strength The left hip pocket: Will have a button and buttonhole, no tab CLUB POCKET: Located 2 ½ below each hip pocket. It shall be ½ from the side seam with a min. opening of 3 ¼ and a min. depth of 8. Material: To be the same as side and hip pockets. Club pockets shall be constructed using the double welt method on a REECE PW machine and finished in such a manner that there is no topstitching The corners of the club pockets: Shall have triangle bartacks for reinforcing strength WATCH POCKET: Shall be located on the right front at the waistband Front of the pocket: Shall be made of pocketing fabric Back of the pocket: Shall be made of basic fabric and 2 pieces are securely stitched together Each corner of the pocket opening: Shall have firm straight bartacks WAISTBAND Shall be constructed using the closed method and shall measure a min. of 2 wide. Content: Must contain ¾ inch Ban-Rol or other monofilament stabilizer to prevent roll over at the trouser front. Waistband closure: Shall be accomplished with a single crush proof hook and eye centered on the waistband for wearer comfort Hook and eye: Shall be reinforced with 7/8 inch non-woven stay tape that is anchored with topstitching through and through to the top of the waistband. The waistband must also be topstitched below the waistband seam through the waistband curtain for added strength. The back center seam of the trouser: To be finished to allow for alterations The outlet in the seat: Is to be in proportion to waist outlet so seat may also be let out. Seat seam: Must be sewn with a tandem needle machine (double needle stitch) for maximum strength WAISTBAND CURTAIN Shall finish a min. 2-1/8 wide Material: Same fabric and color as the pocketing material, and shall be attached to the top of the trouser with a zigzag stitch. The canvas is in the same color and material as the pocketing Content: Must contain Tru-Grip, a ½ surface area composed of thin gauge rubber for max. Comfort and performance. Substitution of silicone strip or strips in place of Tru-Grip shall not be acceptable Composed of: Wet laid non woven canvas. Material wt.: 3.3 oz./ sq. yd. Position: ½ rubberized surface area is positioned 1 ¼ up from the bottom of the curtain RUBBERIZED TRU-GRIP, a ½ surface area composed of thin gauge rubber for max. Comfort and performance. Substitution of silicone strip or strips in place of Tru-Grip shall not be acceptable Page 16 of 59

17 CURTAIN The waistband must be topstitched 1/16 blow the waistband seam for added strength Content: 59% Polyester/ 41% Rubber Count: yarns/ inch Width: 1 1/8 inch Warp: 300 Denier Texturized Polyester Filling: 300 Denier Texturized Polyester Rubber: 55 Gauge WAISTBAND CLOSURE Shall be accomplished with a single crush proof hook and eye centered on the waistband for wearer comfort. Hook and eye: Shall be reinforce with 7/8 non-woven stay tape that is anchored with topstitching through and through to top of the waistband Stitching: In addition to the stitching of the waistband when it is set onto the trouser, the waistband must also be topstitched below the waistband seam through the waistband curtain for added strength Back center seam of the trouser: Is to be finished to allow for alteration Out in the seat: Is to be in proportion to waist outlet so seat may also be let out Seat seam: Must be sewn with a tandem needle machine for maximum strength. Allow trouser size to be increased at least 1 size FLY Zipper: Metal memory lock zipper, metal. French fly tab: On the inside of the right fly, the tab shall be double ply made of the basic cloth The right fly: Shall be lined with the same fabric as the waistband curtain and pocketing. The fly lining: Shall be sewn to the left fly below the zipper in a neat and durable manner Button: Shall be located on the left fly corresponding with the French Fly tab to provide a clean and comfortable closure Tabs made of pocketing material or a grown on French Fly will be cause for rejection Bartack: A firm straight bartack at the bottom of the fly going through the zipper tape. BELT LOOPS Min. of 5 belt loops Style: Keystone style At the top: Measure 1 ¾ in width At the bottom: 1 ¼ in width The center back loop: ¾ wide straight loop The keystone loops: Shall be sewn into the bottom of the waistband and the top of the loops shall be caught into the waistband curtain seam with a Rocap machine The bottom of the center back loop: Shall be tacked to the trouser The top of the loop: Tacked to the outside of the waistband Page 17 of 59

18 ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE 7 MALE LONG SLEEVE SHIRT Fechheimer or equivalent 19W6604 SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC / REQUIRED DOCUMENTATION: Vendor must provide documentation that garment s fabric meets the specifications listed below. Acceptable documents are official manufacturer s fabric brochure or signed letter in company letterhead indicating compliance. Compliance documents must be submitted clearly identifying the Proposal Number, Item number and Item Description. MATERIAL WEIGHT 6.6 oz / sq. yd. CONTENT 65% Dacron Polyester/ 35% Rayon CONSTRUCTION 49 warp x 36 filling yarns per sq. inch. All yarns size 10/1 singles STRENGHT Break strength: 105 lbs warp, 90 lbs filling Tear strength: 9.7 lbs warp 8.5 lbs filling PILLING Min. 4.9 rating COLOR Silver Tan #1985 COLLAR Collar points: 3 long Plastic stays: Fused-in Mylar stays (or equivalent) Collar rear: 1-1/2 Collar stand: 1-5/16 at rear and band to be die cut and interlined with stabilized Mello Press (#285 in collar, Crease N Tack or #250 Dacron Polyester in band). Top enter interlined with # 550 Mello Press. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, then all three are stitched down with a 1/16 raised stitch. Safety stitch joining unacceptable Page 18 of 59

19 EPAULETS Asymmetrical shape topstitched ¼ off the edge to be set on yoke with leading topstitch conforming with front joining seam. To measure 2 at sleeve tapering to 1 3/8 and set not more than ½ from folded collar. Cross stitched 2 from sleeve seam. Creased and edge stitched epaulet construction unacceptable FRONT Buttons: First grade 22 ligne melamine Inside Yoke and Collar band lined with Poly/Cotton Poplin to match Button spacing: The shirt will have 7 buttons and buttonholes on the front, spacing between each will be 3 3/4 except the spacing between the neck button and the first button on the front which will be 3¼ Placket: The left front shall have a top center 1 ¾ wide with two rows of stitches 7/8 apart BADGE REINFORCEMENT Exterior holder: 1 1/8 wide by 2 ¼ deep 2 metal eyelets: Spaced 1 ¼ apart with bottom eyelets centered 1 ½ above left flap. POCKETS 2 Plain breast pockets Measure: 5 5/8 wide, 6 deep Left breast pocket: 1 ½ pencil stitch Position: Each pocket to have Velcro tape ¾ long by ½ wide positioned on both edges of the pocket to correspond with outer scalloped flap points as sample. FLAPS Design: Deep scalloped Measure: 5 7/8 across, 2 ¾ in depth at center point, 2 ¼ at sides. Topstitched ¼ off the edge and secured to shirt front ¼ above pocket Left flap: To have invisible pencil opening 1 ½ to correspond precisely with pencil slot of pocket Both flaps: To be interlined with #550 stabilized Mello Press Creased and edge stitched pocket flap construction unacceptable Underside of the flap: To have Velcro tape ¾ long by ½ wide positioned on outer points of both pocket flaps as sample SLEEVES To be long sleeves cut straight and whole with 5 ½ sleeve vent Elbow reinforcement: Shall extend into the sleeve closing seam Lower facing: Shall measure ½ in width Cuff: To measure 3 with rounded corners with ¼ topstitching 2 buttons: With corresponding buttonholes on each cuff and one button and buttonhole in the sleeve facing STITCHING Single needle throughout, all topstitched ¼ off the edge, sleeve inserting and side close felling seams are to be safety stitched. Page 19 of 59

20 MILITARY CREASES 5 Lintrak creases or equivalent silicone military creases on all shirts Front: 1 crease on each front to be centered vertically through pocket and flap Spacing for three military creases across shirt back to be proportionate to the size of the shirt. CONSTRUCTION Collars, flaps and shoulder straps are made by the conventional construction. Top ply, bottom ply and interlining are first stitched together, then turned right side out, and finally topstitched ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE 8 FEMALE LONG SLEEVE SHIRT Fechheimer or equivalent 103W6604 SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC / REQUIRED DOCUMENTATION: Vendor must provide documentation that garment s fabric meets the specifications listed below. Acceptable documents are official manufacturer s fabric brochure or signed letter in company letterhead indicating compliance. Compliance documents must be submitted clearly identifying the Proposal Number, Item number and Item Description. MATERIAL WEIGHT 6.6 oz / sq. yd. CONTENT 65% Dacron Polyester/ 35% Rayon CONSTRUCTION 49 warp x 36 filling yarns per sq. inch. All yarns size 10/1 singles STRENGHT Break strength: 105 lbs warp, 90 lbs filling Tear strength: 9.7 lbs warp 8.5 lbs filling PILLING Min. 4.9 rating COLOR Silver Tan #1985 Page 20 of 59

21 COLLAR Collar points: 2 7/8 long Plastic stays: Fused-in Mylar stays (or equivalent) Collar rear: 1-1/2 Collar stand: 1-5/16 at rear and to be interlined with stabilized #285 Mello Press and Crease N Tack or #250 Dacron Polyester in band, top center interlined with #550 Mello Press. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, then all three are stitched down with a 1/16 raised stitch. Safety stitch joining unacceptable EPAULETS Asymmetrical shape top stitched ¼ off the edge to be set on yoke with leading topstitch conforming with front joining seam. To measure 2 at sleeve tapering to 1 3/8 and set not more than ½ from folded collar. Cross stitched 2 from sleeve seam. Creased and edge stitched shoulder strap construction unacceptable FRONT Buttons: First grade 22 ligne melamine Inside Yoke and Collar band lined with Poly/Cotton Poplin to match Button spacing: The shirt will have 6 buttons and buttonholes on the front, spacing between each will be 3 ½ except the spacing between the neck button and the first button on the front which will be 3¼ Placket: The right front shall have a top center 1 ½ wide with two rows of stitches 7/8 apart BADGE REINFORCEMENT Exterior holder: 1 1/8 wide by 2 ¼ deep 2 metal eyelets: Spaced 1 ¼ apart with bottom eyelets centered 1 ½ above left flap. POCKETS 2 Plain breast pockets Measure: 5 wide, 5 deep Position: Each pocket to have Velcro tape ¾ long by ½ wide positioned on both edge of pocket to correspond with outer scalloped flap points. FLAPS Design: Deep scalloped Measure: 5 ¼ across, 2 ¼ in depth at center point, 1 ¾ at sides. Topstitched ¼ off the edge and secured to shirt front ¼ above pocket Left flap: To have invisible pencil opening 1 ¼ wide Both flaps: To be interlined with #550 stabilized Mello Press Creased and edge stitched pocket flap construction unacceptable Underside of the flap: To have Velcro tape ¾ long by ½ wide positioned on outer points of both pocket flaps as sample SLEEVES To be long sleeves cut straight and whole with 4 ½ sleeve vent Elbow reinforcement: Shall extend into the sleeve closing seam Page 21 of 59

22 Lower facing: Shall measure ½ in width Cuff: To measure 2 ½ with rounded corners with ¼ topstitching 2 button adjustable cuff STITCHING Single needle throughout, all topstitched ¼ off the edge, sleeve inserting and side close felling seams are to be safety stitched. MILITARY CREASES 5 Lintrak creases or equivalent silicone military creases on all shirts Front: 1 crease on each front to be centered vertically through pocket and flap Spacing for three military creases across shirt back to be proportionate to the size of the shirt. CONSTRUCTION Collars, flaps and shoulder straps are made by the conventional construction. Top ply, bottom ply and interlining are first stitched together, then turned right side out, and finally topstitched -ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE 9 MALE SHORT SLEEVE SHIRT Fechheimer or equivalent 69R6604 SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC / REQUIRED DOCUMENTATION: Vendor must provide documentation that garment s fabric meets the specifications listed below. Acceptable documents are official manufacturer s fabric brochure or signed letter in company letterhead indicating compliance. Compliance documents must be submitted clearly identifying the Proposal Number, Item number and Item Description. MATERIAL WEIGHT 6.6 oz / sq. yd. CONTENT 65% Dacron Polyester/ 35% Rayon CONSTRUCTION 49 warp x 36 filling yarns per sq. inch. All yearns size 10/1 singles STRENGHT Break strength: 105 lbs warp, 90 lbs filling Tear strength: 9.7 lbs warp 8.5 lbs filling Page 22 of 59

23 PILLING Min. 4.9 rating COLOR Silver Tan # 1985 COLLAR Convertible collar shall be 1 piece Collar points: 3 long Plastic stays: Fused-in Mylar stays (or equivalent) Collar to be topstitched ¼ off the edge, to be interlined with #285 Mello Press. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, then all three are stitched down with a 1/16 raised stitch. Safety stitch joining unacceptable EPAULETS Asymmetrical shape top stitched ¼ off the edge to be set on yoke with leading topstitch conforming with front joining seam. To measure 2 at sleeve tapering to 1 3/8 and set not more than ½ from folded collar. Cross stitched 2 from sleeve seam. Creased and edge stitched shoulder strap construction unacceptable FRONT Buttons: First grade 22 ligne melamine Inside Yoke lined with Poly/Cotton Poplin to match Button spacing: The shirt will have 7 buttons and buttons on the front, spacing between each will be 3 ¾ except the spacing between the neck button and the first button on the front which will be 3 ¼ Placket: The left front shall have a top center 1 ½ wide with 2 rows of stitches 7/8 apart. Stitching on the top center is not to be visible on the turn-back facing BADGE REINFORCEMENT Exterior holder to finish 1-1/8 wide x 2 deep with 2 metal eyelets spaced 7/8 apart with bottom eyelet centered 7/8 above left lap POCKETS 2 Plain breast pockets Measure: 5 5/8 wide, 6 deep Left breast pocket: 1 ½ pencil stitch Position: Each pocket to have Velcro tape ¾ long by ½ wide positioned on both edges of the pocket to correspond with outer scalloped flap points as sample. FLAPS Design: Deep scalloped Measure: 5 7/8 across, 2 ¾ in depth at center point, 2 ¼ at sides. Topstitched ¼ off the edge and secured to shirt front ¼ above pocket Left flap: To have invisible pencil opening 1 ½ to correspond precisely with pencil slot of pocket Both flaps: To be interlined with #550 stabilized Mello Press Creased and edge stitched pocket flap construction unacceptable Page 23 of 59

24 Underside of the flap: To have Velcro tape ¾ long by ½ wide positioned on outer points of both pocket flaps as sample SHORT SLEEVES Sleeves are to be straight and whole, to have ¾ hem and to finish 9 long from shoulder seams STITCHING Single needle throughout, all topstitched ¼ off the edge, sleeve inserting and side close felling seams are to be safety stitched. MILITARY CREASES 5 Lintrak creases or equivalent silicone military creases on all shirts Front: 1 crease on each front to be centered vertically through pocket and flap Spacing for three military creases across shirt back to be proportionate to the size of the shirt. CONSTRUCTION Collars, flaps and shoulder straps are made by the conventional construction. Top ply, bottom ply and interlining are first stitched together, then turned right side out, and finally topstitched ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE 10 FEMALE SHORT SLEEVE SHIRT Fechheimer or equivalent 153R6604 SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC / REQUIRED DOCUMENTATION: Vendor must provide documentation that garment s fabric meets the specifications listed below. Acceptable documents are official manufacturer s fabric brochure or signed letter in company letterhead indicating compliance. Compliance documents must be submitted clearly identifying the Proposal Number, Item number and Item Description. MATERIAL WEIGHT 6.6 oz / sq. yd. CONTENT 65% Dacron Polyester/ 35% Rayon CONSTRUCTION 49 warp x 36 filling yarns per sq. inch. All yearns size 10/1 singles STRENGHT Break strength: 105 lbs warp, 90 lbs filling Tear strength: 9.7 lbs warp 8.5 lbs filling Page 24 of 59

25 PILLING Min. 4.9 rating COLOR Silver Tan #1985 COLLAR Convertible collar shall be 1 piece Collar points: 2 7/8 long Plastic stays: Fused-in Mylar stays (or equivalent) Collar to be topstitched ¼ off the edge, to be interlined with #285 Mello Press. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, then all three are stitched down with a 1/16 raised stitch. Safety stitch joining unacceptable EPAULETS Asymmetrical shape top stitched ¼ off the edge to be set on yoke with leading topstitch conforming with front joining seam. To measure 2 at sleeve tapering to 1 3/8 and set not more than ½ from folded collar. Cross stitched 2 from sleeve seam. Creased and edge stitched shoulder strap construction unacceptable FRONT Buttons: First grade 22 ligne melamine Inside Yoke lined with Poly/Cotton Poplin to match Button spacing: The shirt will have 6 buttons and buttons on the front, spacing between each will be 3 ½ except the spacing between the neck button and the first button on the front which will be 3 ¼ Placket: The right front shall have a top center 1 ½ wide with 2 rows of stitches 7/8 apart. Stitching on the top center is not to be visible on the turn-back facing BADGE REINFORCEMENT Exterior holder to finish 1-1/8 wide x 2 deep with 2 metal eyelets spaced 7/8 apart with bottom eyelet centered 7/8 above left lap POCKETS 2 Plain breast pockets Measure: 5 wide, 5 deep Position: Each pocket to have Velcro tape ¾ long by ½ wide positioned on both edge of pocket to correspond with outer scalloped flap points. FLAPS Design: Deep scalloped Measure: 5 ¼ across, 2 ¼ in depth at center point, 1 ¾ at sides. Topstitched ¼ off the edge and secured to shirt front ¼ above pocket Left flap: To have invisible pencil opening 1 ¼ wide Both flaps: To be interlined with #550 stabilized Mello Press Creased and edge stitched pocket flap construction unacceptable Underside of the flap: To have Velcro tape ¾ long by ½ wide positioned on outer points of both pocket flaps as sample Page 25 of 59

26 SHORT SLEEVES Sleeves are to be straight and whole ¾ hem and to finish 8 ½ long from shoulder seam STITCHING Single needle throughout, all topstitched ¼ off the edge, sleeve inserting and side close felling seams are to be safety stitched. MILITARY CREASES 5 Lintrak creases or equivalent silicone military creases on all shirts Front: 1 crease on each front to be centered vertically through pocket and flap Spacing for three military creases across shirt back to be proportionate to the size of the shirt. CONSTRUCTION Collars, flaps and shoulder straps are made by the conventional construction. Top ply, bottom ply and interlining are first stitched together, then turned right side out, and finally topstitched ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE 11 BDU LONG SLEEVE SHIRT (Unisex fitting) Fechheimer or equivalent 528X5810 SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC / REQUIRED DOCUMENTATION: Vendor must provide documentation that garment s fabric meets the specifications listed below. Acceptable documents are official manufacturer s fabric brochure or signed letter in company letterhead indicating compliance. Compliance documents must be submitted clearly identifying the Proposal Number, Item number and Item Description. FABRIC 65% Polyester/35% Cotton Twill, 7.8 oz./sq. yd., Warp: 86 and Filling: 52, Post Cured Finish, Color: Black #0853 COLLAR Convertible collar shall be one piece and measure 3 long at points with fused in Mylar stays (or equivalent) Topstitched ¼ off the edge. Collar to be interlined with #250 Dacron Polyester. FRONT To be made with a revere shirt front having turn back facings of 3. There shall be one button and buttonhole at the lap and 1 additional button and corresponding buttonhole at the bottom of the shirt. In between buttons, there shall be a 15 Talon metal Page 26 of 59

27 zipper closure. A small piece of Velcro, measuring ½ x 1 shall be sewn above the zipper, for additional closure. Th fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, then a three are stitched down with a 1/16 raised stitch. Safety stitch joining unacceptable. SHOULDER STRAPS A symmetrical shape top-stitched ¼ off the edge to be set on yoke with leading topstitch conforming with front joining seam. To measure 2 at sleeve tapering to 1-3/8 and set not more than ½ from folder collar. Cross stitched 2 from sleeve seam. Creased and edge stitched shoulder strap construction unacceptable. A addition microphone holder must be included. The Velcro (microphone holder) shall be placed on the under side of the strap to have loop Velcro measuring 1 x 2 and shall be placed between the cross-stitch and buttonhole. The shoulder (yoke) to have corresponding hook velcro. POCKETS Two breast pockets with inverted pleats. Pocket to measure 6 wide, 6 deep. Left breast pocket to have a 1 ½ pencil stitch. Each pocket to have Velcro tape ¾ long by ½ wide, positioned on both edges of pocket to correspond with outer square flap points. FLAPS Rectangular flap design to measure 6-1/4 across and 2-1/4 in depth. Secured to shirt front ¼ above pocket. Topstitched ¼ off the edge. Left flap to have invisible pencil opening 1-1/2 to correspond precisely with pencil slot of pocket. Both flaps to be interlined with Dacron #250. Creased and edge stitched pocket flap construction unacceptable. Underside of the flap to have Velcro tape ¾ long by ½ wide, positioned on outer points of both pocket flaps as sample. SLEEVES Straight at width no bias of one piece shaped at head, jacket type. Sleeve vent 5-1/2 long with continuous narrow sleeve facing ½ wide. CUFFS To measure 2-1/2 in depth with squared corners as sample. Topstitched ¼ off the edge. Two button adjustable cuff. Both cuffs to be interlined with #250 Dacron Polyester or equivalent. BUTTONS First grade 20-ligne melamine to match STITCHING Single needle throughout. All topstitched ¼ off the edge. Sleeve inserting and side close felling safety stitched THREAD All sewing threads to be fast color polyester core polyester wrap to match. CONSTRUCTION Collars, flaps, cuffs and shoulder straps are made by the conventional construction. Top ply, bottom ply and interlining are first stitched together, then turned right side out, and finally topstitched. Page 27 of 59

28 PRODUCT SIZES Product shall be manufactured and / or in-stock in the following sizes: NECK SIZES Small - 14 & 14- ½ Medium - 15 & 15- ½ Large - 16 & 16- ½ XL - 17 & 17- ½ XXL - 18 & 18- ½ XXXL- 19 & 19- ½ XXXXL - 20 & 20- ½ SLEEVE LENGTHS Shorts to finish 32 Regular to finish 34 Long to finish 36 Xlong to finish 38 LABELS Shirt must have a care label permanently affixed that also indicates the size. A paper ticket showing the size, fabric content, cut number, and WPL number must be on the outside of the shirt. ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE 12 BDU COMMAND TROUSERS WITH CARGO & CLUB POCKETS Fechheimer or equivalent SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC / REQUIRED DOCUMENTATION: Vendor must provide documentation that garment s fabric meets the specifications listed below. Acceptable documents are official manufacturer s fabric brochure or signed letter in company letterhead indicating compliance. Compliance documents must be submitted clearly identifying the Proposal Number, Item number and Item Description. FABRIC 65% Polyester / 35% Cotton Twill, 6.5 Oz/Square Yard, 2x1 Twill Weave, Warp: 86 Filling: 52, Post Cured Finish COLOR: Black, #0853 DESIGN Trouser shall be manufactured from a men's uniform trouser pattern. The trouser shall incorporate a plain front, two (2) quarter top front pockets and two (2) hip pockets two club pockets, one below each hip pocket. Trouser to be straight leg style. YES DOCUMENTATION INCLUDED? NO Page 28 of 59

29 POCKETING The pocketing shall be 70% Polyester / 30% Cotton, 2.9 oz. per square yard (60" width) with a minimum 78 X 64 count. Pocketing must have a durable press finish and the color of the pocketing must be black. POCKET DESIGN The two (2) front pockets will be quarter top style with a minimum opening of 6" and a minimum depth of 5 3/4" measured from the bottom of the pocket opening. Pockets shall be constructed using the stitch, turn, and topstitch method. Pocket facings shall be made of the basic fabric and shall measure a minimum of 3" in width. The front pockets shall be double tipped. The two (2) hip pockets shall have a minimum opening of 5 1/2" and a minimum depth of 5 3/4" measured from the bottom of the pocket opening with rectangular pocket flaps to close with Velcro. Hip pockets shall be constructed using the double welt method on a REECE PW Machine (or equal) and the welts shall be finished in such a manner that there is no top stitching (top stitched hip pockets shall be cause for rejection). The corners of the hip pocket openings shall have firm straight bartacks for reinforcing strength (triangle bartacks are unacceptable). There shall be club pockets located 4 " (plus or minus 1/4") below each hip pocket. The club pockets shall be 2" (plus or minus 1/4") from the side seam with a minimum opening of 3 1/4 " and a minimum depth of 7-1/4 ". Pocketing material to be the same as side and hip pockets. Club pockets shall be constructed using the double welt method on a REECE PW machine and finished in such a manner that there is no topstitching (topstitched club pockets shall be cause for rejection). The corners of the club pockets shall have shall have firm straight bartacks for reinforcing strength (triangle bartacks are unacceptable). CARGO POCKET There shall be two cargo pockets, one on each side seam. There will be double-section pleated patch pockets with rectangular flaps to close with Velcro. The pockets will be centered across the side seam and placed 2" below the bottom of the front quarter-top pocket, measuring from the top of the pocket flap. The pocket shall be constructed of the shell fabric and lined with the specified pocketing. The top edge of the pocket shall be bound. The outside measurements of the pocket are 7" wide x 8½" deep with mitered bottom corners. There shall be a 1½" center pleat on each pocket. There shall be a 1½" wide x 1" deep piece of Velcro (hook side) sewn to the inner ply of the flap and a corresponding piece of Velcro (loop side) sewn on the pleat of the pocket. There shall be a black molded plastic zipper sewn behind the inner pocket and to the trouser leg so that the zipper is recessed 1" from the top of the pocket flap. There shall be straight vertical bartacks on all four corners of each pocket flap. WAISTBAND The trouser will include a two zone stretch waistband with a Tru-Grip, a ½ surface area composed of thin gauge rubber for max. Comfort and performance. Substitution of silicone strip or strips in place of Tru-Grip shall not be acceptable. The two way stretch waistband curtain is designed to provide the wearer with maximum comfort, functionality, and professional appearance. The waistband itself shall be constructed using the "closed method" and shall measure a minimum of 1-7/8" wide when finished. The waistband closure shall be accomplished with a single crush proof hook and eye centered on the waistband for maximum wearer comfort. The hook and eye shall be reinforced with 7/8-inch non-woven stay tape that is anchored with topstitching through and through to the top of the waistband (bartacks in place of topstitching Page 29 of 59

30 shall be cause for rejection). In addition to the stitching of the waistband when it is set onto the trouser, the waistband must also be topstitched below the waistband seam through the waistband curtain for added strength. The back center seam of the trouser to be finished to allow for alterations (with ample basic trouser fabric and waistband curtain material to allow trouser size to be increased at least one size). The outlet in the seat is to be in proportion to waist outlet so seat may also be let out. Seat seam must be sewn with a tandem needle machine (double-needle stitch) for maximum strength. The two zone curtain with Tru-Grip is composed with a two zone stretch feature to provide the wearer maximum comfort and security. The top part of the waistband curtain is a lower stretch zone designed to give with the wearer s movements including sitting or bending. This upper zone of the waistband curtain is composed of a 1-1/2-inch 30% stretch monofilament elastic that is around the entire waistband providing stability, preventing waistband rollover, and allowing for a comfort stretch with wearer movement. The specifications for the upper elastic are as follows: Width: 1-1/2-inch Stretch: 30% Warp: 150 Denier textured polyester, 21 ends Filling element 1:.011 diameter transparent type 66 Nylon, one end Filling element 2: 150 denier textured polyester, 2 ends Elastomer: 840 denier transparent spandex, 21 ends Overall contents: 59% polyester, 41% rubber. The upper zone of the waistband curtain interlining (elastic band) is to be lined in the same color and material as the trouser pocketing and it shall be cut on a 45-degree bias to allow for maximum stretch. The waistband trouser fabric shall be cut across the cloth to allow for maximum stretch in synergy with the two zone stretch with Tru-Grip, a ½ surface area composed of thin gauge rubber for max, comfort and performance. Substitution of silicone strip or strips in place of Tru-Grip shall not be acceptable The lower part or lower zone of the waistband shall be the same color as the trouser pocketing. It is designed to stretch over the hips for comfort, help keep the trouser securely positioned on the wearer s waist, and to help prevent slippage. This lower portion of the waistband curtain is made with 65% stretch elastic. This zone also incorporates Tru-Grip, a ½ wide rubberized surface area which acts to hold the shirt in place inside the trouser to help keep shirt tails tucked into the waist for a neat and professional appearance. (Use of a single silicone strip or strips instead of ½ wide rubberized surface area shall be cause for rejection.) The specifications for the lower elastic are as follows: Width: 1-3/4-inch Stretch: 65% Face: 70/2 stretch nylon, 104 ends Binder: 150/2 textured polyester, 32 ends Edge: 70/2 stretch nylon, 11 ends Figure: 100/2 stretch nylon, 16 ends Rubberized area: 55 gauge rubber, 33 ends Catch Thread: 70/2 stretch nylon, 1 end Elastomer Core: 1680 Lycra, 38 ends Page 30 of 59

31 Elastomer top cover: 150/1 textured polyester, 1 end Elastomer bottom cover: 100/1 bright nylon, 1 end Filling: 250 monofilament nylon, 2 ends Overall contents: 46% nylon, 15% polyester, 25% rubber, 14% spandex. FLY Trouser shall have a metal memory lock zipper. There shall be a buttonhole on the inside right fly. The right fly shall be lined with the same fabric as the waistband curtain and pocketing. The fly lining shall be sewn to the left fly below the zipper in a neat and durable manner. A button shall be located on the left fly corresponding with the buttonhole. There shall be a firm straight bartack at the bottom of the fly going through the zipper tape. BELT LOOPS There shall be a minimum of seven (7) belt loops 1" in width of double thickness. Each loop must have a non-woven interlining. All loops must be "dropped" with the bottom of the belt loop tacked to the trouser. The top of all belt loops (except for the center back loop) shall be caught into the waistband curtain seam with a Rocap Machine (or equal). The top of the center back loop shall be tacked to the waistband. CREASES The leg creases, front and back will have a Lintrak creases or equivalent silicone bead put in by using the Lintrak creases or equivalent process. STITCHING, PRESSING & FINISHING Trouser must be stitched with matching thread and all stitching to show must be stitches per inch. Trouser must be neatly pressed on Hothead Presses and properly shaped. Outseams and inseams must be pressed open. Trouser must be oven baked after pressing. Trouser must be cleaned and finished to eliminate loose threads. LABELS Trouser must have a care label permanently affixed that also indicates the size. A paper ticket showing the size, fabric content, cut number, and WPL number must be on the outside of the waistband. Trouser shall have a label stating, This garment meets the specifications of the San Francisco Sheriff s Department. STOCK SIZES Trouser shall be available in the following stock sizes: REGULAR RISE Even Only Over 38 ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE 13 SHERIFF S CADET: BLACK REVERSIBLE HIGH- VISIBILITY JACKET Fechheimer or equivalent SPECIFICATIONS AND ESSENTIAL FEATURES Page 31 of 59

32 FABRIC Outer shell: 100% nylon 3-ply Supplex Lining (reversible side): 100% Polyester high-visibility fluorescent yellow BASIC DESIGN Jacket to have windproof, waterproof, and breathable membrane with all seams properly sealed and shall meet ANSI standard. It shall be full cut with a butted reversible molded plastic zipper to the top of collar COLLAR Collar facing to extend to top edge of upper reflective stripe on the fluorescent yellow side Collar points: Shall be well shaped and symmetrical, the collar shall be top stitched with collar points long enough for a neat appearance Permanent collar and collar stand: Shall be made of 2 plies of the basic fabric plus the interlining Collar interlining: Shall be sewn to the under collar and the under collar stand Top of collar: With a black molded plastic reversible zipper BODY DESIGN The fronts: Shall be plain with patch pockets measuring 6 ¾ wide by 7 deep with top edge of pocket turned in and finished ¾ so there are no raw edges Pleat: Inverted pleat shall be 1 ½ wide. Pleat shall be sewn to open 4 Side opening of pocket: 5 to allow access to the hand warmer compartment/pocket Flap: 7 ¼ across, 2 ¼ at each side, and 3 at center point where there shall be a horizontally positioned dummy buttonhole to accommodate a metal button. Flap and pocket are to have small snaps at each end to close separate top opening compartment/pocket. Left pocket flap to have hidden pen opening on left side 1 ½ wide, bartacked at each side Black metal eyelets: There shall be 4 weep holes on navy side, at front and back of jacket, both sides, 1 ¾ from side zippered vents WAISTBAND Separate waistband shall measure 2 ¼, plain across the front, elasticized across the back with 2 rows of stitching through the center Spacing: 2 rows of stitching each ½ apart, centered on the waistband, and extending through the elastic. Side zipper vents: Shall be butted and finish 9 ½ long Zipper: Black nylon reversible Elasticized tabs: 3 ½ long by 1 wide and to snap on the front of jacket Additional snap: Shall be positioned 1 ¼ towards back of jacket waistband to hold tab in place if not utilized by wearer SLEEVES Shall be 2 piece modified raglan style with 8 nylon zipper on black side to allow for access inside coat for emblem sewing The bottom: Shall have a 2 cuff, elasticized shirred with 3 rows of stitching across the back, with 1 ½ wide by 2 ½ long tab on front side of cuff with Velcro for adjustable closure Loop side of Velcro on cuff: 4 long by 1 wide and to attach to hook side of Velcro on bottom side of tab 1 ½ long by 1 wide Page 32 of 59

33 Back metal eyelets: There shall be 2 weep holes spaced 1 from cuff on front and back sides of sleeves EPAULETS To be 1 ¾ wide tapering slightly to a point, cross stitched, and permanently inserted into armhole. Pointed end of shoulder strap to be tacked in place. There shall be a horizontally positioned dummy buttonhole to accommodate a metal button SILVER REFLECTIVE TAPE ANSI 2 standard placed on the fluorescent yellow side of jacket. There shall be 2 rows on body of coat and sleeves Silver reflective tape: 2 wide with black edge The top row on the body of coat: 1 down from armhole The bottom row: 1 from waistband and shall continue around back of jacket with stripes on back lining up with stripes on front Sleeves: Have 2 rows of reflective tape positioned so that the top row is 5 down from armhole and bottom row to be 4 from cuff. Tape on sleeves to line up at sleeve seams. Both rows of reflective tape on body shall line up at butted front zipper closure Jacket must be third party certified ANSI 2 by an independent company BADGE TAB Both sides of jacket to have badge tab coordinating with color/fabric. To be positioned on left breast measuring 2 ½ long by 7/8 wide with 2 metal eyelets 1 ¼ apart, center to center INTERLININGS Front opening, collar, pocket flaps, cuffs, shoulder straps, and waistband to be interlined with pellon FINISHING & PRESSING The entire jacket must be made in a first class manner. Industrial construction will not be acceptable. All loose threads must be removed and jacket must be completely pressed with proper pressing equipment and properly shaped. COLOR BLACK, #BLK01 REVERSIBLE COLOR, FLOYEL01 STOCK SIZES To be available from stock in the following sizes: Regular XS to 5XL Longs M to 5XL Extra Longs L to 4XL Page 33 of 59

34 ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE 14 SHERIFF S CADET: MALE LONG SLEEVE SHIRT Fechheimer or equivalent 45W6621 SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC / REQUIRED DOCUMENTATION: Vendor must provide documentation that garment s fabric meets the specifications listed below. Acceptable documents are official manufacturer s fabric brochure or signed letter in company letterhead indicating compliance. Compliance documents must be submitted clearly identifying the Proposal Number, Item number and Item Description. MATERIAL WEIGHT oz / Linear yd. FABRIC CONTENT 65% Dacron Polyester/35% Rayon, Deluxe Tropical CONSTRUCTION 49 warp x 36 filling yarns per sq. inch. All yarns size 10/1 singles COLOR Silver Grey, #3229 COLLAR Collar points: 3 Interlining: Woven interlining of #285 Stabilized Mello-Press. Non-woven interlining unacceptable and shall be cause for rejection Plastic stays: Fused-in Mylar stays, (or equivalent) to be 2 ¾ long 3/8 min. width, and to be fused to underside of collar interlining. Stays applied directly to collar material itself unacceptable Collar rear: 1 ½ Collar stand: 1-5/16 and band to be interlined with Crease-N-Tack or #250 Dacron Polyester in the band. Collar stand to be lined with poly/cotton to match Page 34 of 59

35 FRONT Buttons: First grade 20-ligne melamine, have 7 buttons and buttonholes on the front Button spacing: 3 ¾ except the spacing between the neck button and the first button on the front which will be 3 ¼ Placket: 1 ½ wide with 2 rows of stitches 7/8 apart, top center placket to have woven interlining of # 550 Stabilized Mello-Press. Non-woven interlining unacceptable and shall be cause for rejection. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, and then all three are stitched down with a 1/16 raised stitch. Safety stitch joining unacceptable. EPAULETS 2-piece pointed, ¼ topstitched and to be set on yoke with leading topstitch conforming to front joining seam. To measure 2 at sleeve tapering to 1-3/8 and set not more than ½ from collar set seam. Cross-stitched 2 from sleeve seam. Shoulder straps to have functional buttonhole to attach to sewn button on shoulder of shirt. Edge stitched shoulder strap construction unacceptable BADGE REINFORCEMENT 2-ply sling 1 wide centered over left pocket and stitched to shoulder seam and flap setting stitch. It shall have 2 buttonhole eyelets 1 ¼ from top of pocket flap spaced 1 ¼ apart and centered on sling POCKETS Measure: 5-5/8 wide, 6 deep Breast patch pocket: Two, with mitered corners and 1 ½ stitched pleats Pleats: Shall be stitched top and bottom and full length of pleat to prevent spreading Left breast pocket: Have 1 ½ pencil stitch Hook Velcro: Each pocket to have a ¾ long by ½ wide hook Velcro, positioned on both edges of pocket to correspond with outer scalloped flap points as specified. Velcro to be stitched all sides and to be sewn through pocket and shirt for added reinforcement STOCK SIZES Shirts must be available in the following sizes: SLEEVE LENGTHS inches NECK SIZES 14- ½ to 18- ½, 19, 20, 21, and Page 35 of 59

36 32 X X X X X X X 33 X X X X X X X X X X X X 34 X X X X X X X X X X X X 35 X X X X X X X X X X X X 36 X X X X X X X X X X X 37 X X X X X X X X 38 X X X X X X X X X X ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE 15 SHERIFF S CADET: MALE SHORT SLEEVE SHIRT Fechheimer or equivalent 95R6621 SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC / REQUIRED DOCUMENTATION: Vendor must provide documentation that garment s fabric meets the specifications listed below. Acceptable documents are official manufacturer s fabric brochure or signed letter in company letterhead indicating compliance. Compliance documents must be submitted clearly identifying the Proposal Number, Item number and Item Description. MATERIAL WEIGHT oz / Linear yd. FABRIC CONTENT 65% Dacron Polyester/35% Rayon, Deluxe Tropical CONSTRUCTION 49 warp x 36 filling yarns per sq. inch. All yarns size 10/1 singles COLOR Silver Grey, #3229 Page 36 of 59

37 COLLAR 1 piece convertible collar, collar topstitched ¼ off the edge, collar material itself shall have no fusing to Mylar stays (or equivalent) or collar interlining Collar points: 3 Plastic stays: Ultrasonically fused-in Mylar stays (or equivalent), have woven interlining of # 285 Stabilized Mello-Press. Stays to be 2 ½ long, 3/8 min., and to be fused to underside of collar interlining. Stays applied directly to collar material itself unacceptable. Collar stand: 1-5/16 and band to be interlined with Crease-N-Tack or #250 Dacron Polyester in the band. FRONT Buttons: Have 7 buttons and buttonholes on the front Inside yoke to be lined with poly/cotton to match. Button spacing: 3 ¾ except the spacing between the neck button and the first button on the front, which will be 2 ½ Placket: Each front shall have a facing 3 in width, the left front shall have a top center placket 1 ½ wide with 2 rows of stitches 7/8 apart. Stitching on top center is not to be visible on the turn-back facing. Top center placket to have woven interlining #550 Stabilized Mello-Press. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, and then all three are stitched down with a 1/16 raised stitch Non woven interlining is unacceptable and shall be cause of rejection. EPAULETS To be 2-piece pointed, ¼ topstitched and to be set on yoke with leading topstitch conforming to front joining seam. To measure 2 at sleeve tapering to 1 3/8 and set not more than ½ from collar set seam. Cross-stitched 2 from sleeve seam. Shoulder strap to have functional buttonhole to attach to sewn button on shoulder of shirt. Edge stitched shoulder strap construction unacceptable. BADGE REINFORCEMENT 2-ply sling 1 wide centered over left pocket and stitched to shoulder seam and flap setting stitch. It shall have 2 buttonhole eyelets 1 ¼ from top of pocket flap spaced 1 ¼ apart 1 ¼ apart and centered on sling POCKETS Measure: 5-5/8 wide, 6 deep Breast patch pocket: Two, with mitered corners and 1 ½ stitched pleats Pleats: Shall be stitched top and bottom and full length of pleat to prevent spreading Left breast pocket: Have 1 ½ pencil stitch Hook Velcro: Each pocket to have a ¾ long by ½ wide hook Velcro, positioned on both edges of pocket to correspond with outer scalloped flap points as specified. Velcro to be stitched all sides and to be sewn through pocket and shirt for added reinforcement FLAPS Construction: 2 piece deep scalloped design to measure 5-7/8 across and 2 ¾ in depth at center point, 2 ¼ at sides. Secured to shirtfront 3/8 above pocket. Flaps to be ¼ topstitched. Flaps to have woven interlining of #550 stabilized Mello-Press. Each flap shall have a button centered on uncut sewn buttonhole Left flap: To have invisible pencil opening 1 ½ to correspond precisely with pencil slot of pocket Page 37 of 59

38 Underside of the flap: To have looped Velcro ¾ long by ½ wide stitched all sides, positioned on outer points of both pocket flaps to secure with corresponding Velcro strips on shirt pocket Creased and edge stitched pocket flap construction unacceptable. Stop & start stitching for pencil opening unacceptable and shall be cause for rejection SLEEVES To be straight and whole and to have a ¾ hem and to finish at a min. of 9 ½ long from shoulder seam SEWING Collar, shoulder straps and pocket flaps to be topstitched ¼ off the edge. Sleeve inserting and side close felling seams are to be safety stitched THREAD All sewing threads to be color fast polyester wrap to match. INTERLININGS Collar interlined with # 285 Stabilized Mello-Press. Pocket flaps, shoulder straps and top center to be interlined with # 550 Stabilized Mello-Press. Collar band to be interlined with Crease-N-Tack or #250 Dacron Polyester in the band. MILITARY CREASES There shall be five Lintrak creases or equivalent silicone sharp military creases on all shirts. One crease on each front to be centered vertically. Front creases shall be through pockets and flaps. Spacing for three military creases across shirt back to be proportionate to the size of the shirt. STOCK SIZES: Shirts must be available in the following neck sizes: Small Med Large Extra Large 2 Extra Large 3 Extra Large 4 Extra Large ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE 16 SHERIFF S CADET: FEMALE LONG SLEEVE SHIRT Fechheimer or equivalent 102W6621 Page 38 of 59

39 SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC / REQUIRED DOCUMENTATION: Vendor must provide documentation that garment s fabric meets the specifications listed below. Acceptable documents are official manufacturer s fabric brochure or signed letter in company letterhead indicating compliance. Compliance documents must be submitted clearly identifying the Proposal Number, Item number and Item Description. MATERIAL WEIGHT oz / Linear yd. FABRIC CONTENT 65% Dacron Polyester/35% Rayon, Deluxe Tropical CONSTRUCTION 49 warp x 36 filling yarns per sq. inch. All yarns size 10/1 singles COLOR Silver Grey, #3229 COLLAR Collar material itself shall have no fusing to Mylar stays (or equivalent)or collar interlining Collar points: 2-7/8 Plastic stays: Ultrasonically fused-in Mylar stays (or equivalent). Collar to have woven interlining of # 285 Stabilized Mello-Press. Stays to be 2 ½ long, 3/8 min. width, and to be fused to underside of collar interlining. Stays applied directly to collar material itself unacceptable Collar rear: 1 ½, collar topstitched ¼ off the edge Collar stand: 1-5/16 at rear and band to be interlining with Crease-N-Tack or #250 Dacron Polyester in the band. FRONT Buttons: First grade 20-ligne melamine. The shirt will have 6 buttons and buttonholes on the front Button spacing: 3 ½ except the spacing between the neck button and the first button on front, which will be 3 ¼ Placket: The right front shall have a top center placket 1 ½ wide with 2 rows of stitches 7/8 apart. Top center placket to have woven interlining of # 550 Stabilized Mello-Press. Non-woven interlining unacceptable and shall be cause for rejection. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, and then all three are stitched down with a 1/16 raised stitch EPAULETS 2-piece pointed, ¼ topstitched and to be set on yoke with leading topstitch conforming with front joining seam. To measure 2 at sleeve tapering to 1 3/8 and set not more than ½ from collar set seam. Cross-stitched 2 from sleeve seam. Shoulder straps to have functional buttonhole to attach to sewn button on shoulder of shirt. Edge stitched shoulder strap construction unacceptable. Page 39 of 59

40 BADGE REINFORCEMENT 2-ply sling 1 wide centered over left pocket and stitched to shoulder seam and flap setting stitch. It shall have 2 buttonhole eyelets 1 ¼ from top of pocket flap spaced 1 ¼ apart and centered on sling POCKETS Measure: 5 wide, 5 deep Breast patch pocket: Two, with mitered corners and 1 ¼ stitched pleats Pleats: Shall be stitched top and bottom and full length of pleat to prevent spreading Hook Velcro: Each pocket to have a ¾ long by ½ wide hook Velcro, positioned on both edges of pocket to correspond with outer scalloped flap points as specified. Velcro to be stitched all sides and to be sewn through pocket and shirt for added reinforcement FLAPS 2-piece deep scalloped design to measure 5 ¼ across and 2 ¼ in depth at center point, 1 ¾ at sides. Secured to shirtfront 3/8 above pocket Construction: Flaps to be ¼ topstitched. Flaps to have woven interlining of # 550 stabilized Mello-Press. Each Flap shall have a button centered on uncut sewn buttonhole Left flap: flap to have invisible pencil opening 1 ¼. Stop & start stitching for pencil opening unacceptable and shall be cause for rejection Underside of the flap: To have looped Velcro ¾ long by ½ wide stitched all sides, positioned on outer points of both pocket flaps to secure with corresponding Velcro strips on shirt pocket Creased and edge stitched pocket flap construction unacceptable SLEEVES Sleeve vent shall be a min. of 4 ½ long with one-piece top and bottom facings. Facing to measure 1-1/8 wide point blacked at top CUFFS 2 piece ½ hemmed cuff with ¼ topstitching. Cuffs to measure 2 ½ in depth with rounded corners (barrel cuffs). Cuffs to be two button adjustable. Cuffs to have woven interlining of # 550 Stabilized Mello-Press SEWING Collar, shoulder straps, pocket flaps and cuffs to be topstitched 1/4" off the edge. Sleeve inserting and side close felling seams are to be safety stitched. THREAD All sewing threads to be color fast polyester wrap to match. INTERLININGS Collar interlined with # 285 Stabilized Mello-Press. Cuffs, pocket flaps, shoulder straps and top center to be interlined with #550 Stabilized Mello-Press. Collar band to be interlined with Crease-N-Tack or #250 Dacron Polyester in the band. MILITARY CREASES There shall be five Lintrak creases or equivalent silicone sharp military creases on all shirts. One crease on each front to be centered vertically. Front creases shall be through pockets and flaps. Spacing for three military creases across shirt back to be proportionate to the size of the shirt. Page 40 of 59

41 CONSTRUCTION Collars, flaps and cuffs are made with conventional construction. Top ply, bottom ply and interlining are first stitched together, then turned right side out and finally topstitched. STOCK SIZES Shirts must be available in the following sizes: Bust sizes: Sleeve lengths: 28, 30 Regular = 30 32, 34 Regular = 30 Long = 31 36, 38 Regular = 31 Long = 32 40, 42 Regular = 32 Long = 33 44, 46 Regular = 33 Long = & Up Regular = 34 Long = 35 ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE 17 SHERIFF S CADET: FEMALE SHORT SLEEVE SHIRT Fechheimer or equivalent 152R6621 SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC / REQUIRED DOCUMENTATION: Vendor must provide documentation that garment s fabric meets the specifications listed below. Acceptable documents are official manufacturer s fabric brochure or signed letter in company letterhead indicating compliance. Compliance documents must be submitted clearly identifying the Proposal Number, Item number and Item Description. MATERIAL WEIGHT oz / Linear yd. FABRIC CONTENT 65% Dacron Polyester/35% Rayon, Deluxe Tropical CONSTRUCTION 49 warp x 36 filling yarns per sq. inch. All yarns size 10/1 singles Page 41 of 59

42 COLOR Silver Grey, #3229 COLLAR 1 piece convertible collar Collar points: 2-7/8 Plastic stays: Ultrasonically fused-in Mylar stays (or equivalent). Stays to be 2 ½ long. 3/8 min. width, and to be fused to underside of collar interlining. Stays applied directly to collar material itself unacceptable Woven interlining: # 285 Stabilized Mello-Press Construction: Collar topstitched ¼ off the edge. Collar material itself shall have no fusing to Mylar stays (or equivalent) or collar interlining FRONT Buttons first grade 20-ligne melamine. The shirt will have 6 buttons and buttonholes on the front Button spacing: 3 ½ except the spacing between the neck button and the first button on the front which will be 2 ½ Placket: Each front shall have a facing 3 in width. The right front shall have a top center placket 1 ½ wide with 2 rows of stitches 7/8 apart. Stitching on top center is not to be visible on the turn-back facing. Top center placket to have woven interlining of # 550 Stabilized Mello-Press. Non-woven interlining unacceptable and shall be cause for rejection The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, and then all three are stitched down with a 1/16 raised stitch EPAULETS 2-piece pointed, ¼ topstitched and to be set on yoke with leading topstitch conforming to front joining seam. To measure 2 at sleeve tapering to 1-3/8 and set not more than ½ from collar set seam. Cross-stitched 2 from sleeve seam. Shoulder strap to have functional buttonhole to attach to sewn button on shoulder of shirt. Edge stitched shoulder strap construction unacceptable BADGE REINFORCEMENT 2-ply sling 1 wide centered over left pocket and stitched to shoulder seam and flap setting stitch. It shall have 2 buttonhole eyelets 1 ¼ from top of pocket flap spaced 1 ¼ apart and centered on sling POCKETS Measure: 5 wide, 5 deep Breast patch pocket: Two, with mitered corners and 1 ¼ stitched pleats Pleats: Shall be stitched top and bottom and full length of pleat to prevent spreading Hook Velcro: Each pocket to have ¾ long by ½ wide hook Velcro, positioned on both edges of pocket to correspond with outer scalloped flap points as specified. Velcro to be stitched all sides and to be sewn through pocket and shirt for added reinforcement FLAPS 2-piece deep scalloped design to measure 5 ¼ across and 2 ¼ in depth at center point, 1 ¾ at sides. Secured to shirtfront 3/8 above pocket Construction: Flaps to be ¼ topstitched, to have woven interlining of #550 Stabilized Mello-Press. Each flap shall have a button centered on uncut sewn buttonhole Page 42 of 59

43 Left flap: to have invisible pencil opening 1 ¼. Stop & start stitching for pencil opening unacceptable and shall be cause for rejection Underside of the flap: To have looped Velcro ¾ long by ½ wide stitched all sides, positioned on outer points of both pocket flaps to secure with corresponding Velcro strips on shirt pocket Crease and edge stitched pocket flap construction unacceptable SLEEVES To be straight and whole and to have a ¾ hem and to finish at a min. of 8 ½ long from shoulder seam SEWING Collar, shoulder straps and pocket flaps to be topstitched ¼ off the edge. Sleeve inserting and side close felling seams are to be safety stitched THREAD All sewing threads to be color fast polyester wrap to match. INTERLININGS Collar interlined with #285 Stabilized Mello-Press. Pocket flaps, shoulder straps and top center to be interlined with # 550 Stabilized Mello-Press. MILITARY CREASES There shall be five sharp Lintrak creases or equivalent silicone military creases on all shirts. One crease on each front to be centered vertically. Front creases shall be through pockets and flaps. Spacing for three military creases across shirt back to be proportionate to the size of the shirt. STOCK SIZES Shirts must be available in the following sizes: Bust sizes: 30, 32, 34, 36, 38, 40, 42, 44, 46, 48 ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE 18 SHERIFF S COMMAND STAFF LONG-SLEEVE SHIRT (UNISEX) Fechheimer or equivalent 15W5400 SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC / REQUIRED DOCUMENTATION: Vendor must provide documentation that garment s fabric meets the specifications listed below. Acceptable documents are official manufacturer s fabric brochure or signed letter in company letterhead indicating compliance. Compliance documents must be submitted clearly identifying the Proposal Number, Item number and Item Description. Page 43 of 59

44 COLOR White, #81 FABRIC Shall be a Poplin weave, 65% Dacron Polyester/35% Combed Cotton with a finished weight of 4.0 to 4.25 oz. per square yard with a minimum thread count of 104 warp yarns and 54 filling yarns per square inch. Shall have a Permanent Press, Soil Release finish. To be Flying Cross #15W5400. STYLE Shirt shall be made in coat style, form-fitting, with banded collar, shoulder straps, badge reinforcement and two pleated outside breast pockets with scalloped flaps. It will have long sleeves with two button barrel cuffs, one button on sleeve facing COLLAR Shall consist of leaf and stand of two-ply with permanently fused-in Mylar stays (or equivalent) properly positioned with each collar point. Collar to be styled as sample, with collar points 3 1/4" in length, 1 1/2" in height at back. Collar stand to measure 1 5/16" in height at back and have one button and buttonhole at front. Collar and band to be die cut to insure uniformity. EPAULETS The epaulets shall be pointed at the end toward the neck of the shirt. The other end shall be sewn in sleeve head seam. The pointed ends shall be fastened with one button. To measure 2" at sleeve and tapered to 1-3/8". Epaulets to be set about 1/2" from the collar. Epaulets shall be box-stitched to shoulders with row of cross-stitching 2" from sleeve head seam, and diagonally across from each end of seam to the sleeve head seam. Epaulets to be top stitched 1/8" off the edge. Creased and edge stitched shoulder strap construction unacceptable BADGE REINFORCEMENTS Shall have a two-ply sling type badge reinforcement inside left front of shirt, 1" wide to be centered and secured in left shoulder seam and left flap setting seam. Two buttonhole eyelets are to be spaced 1 1/4" apart with the bottom eyelet 1 1/4" from the top of the left pocket flap. FRONTS Left: To have 1 5/8" turned back selvage edge facing along front edge. Facing to be held in position only by 6 wellsewn buttonholes. Right: To have 1" hemmed self-button piece along front edge with 6 buttons to correspond with left front buttonholes. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front edges of the yoke are turned under, with the front sandwiched between, and then all three are stitched down with a 1/16" raised stitch. Safety stitch joining is unacceptable. POCKETS The shirt shall have two outside 1 1/4" pleated breast pockets with scalloped flaps. Flap to finish 2 3/4" at center point and 2 1/4" at sides. Flaps to be secured to front of Shirt 1/4" above pocket. Left flap is to have invisible pencil opening 1 1/2" wide. Pocket shall be clip corner design to finish 5 5/8" wide and 6" deep. The left breast pocket is to have a pencil stitch 1 1/2" wide. Creased and edge stitched pocket flap construction unacceptable. Page 44 of 59

45 SLEEVES & CUFFS To be long sleeve cut straight and whole with pleats and 5 1/2" sleeve vent. Sleeve vent shall have a top facing 1 1/8" wide finished at the top with a neatly 1 1/8" wide finished at the top with a neatly 1 1/8" wide finished at the top with a neatly 1/2" in width. Cuff to measure 2 1/2" with rounded corners. There shall be two buttons with corresponding buttonholes on each cuff and one button and buttonhole in the sleeve facing. BUTTONS Shall be first grade, pearlescent plastic, 19 ligne to match. SEWING Collar and pocket flaps shall be stitched 1/8 inch from edge. Side closing and sleeve setting shall be made with safetystitch type machine. All stitching will be with not fewer than 12 to 14 stitches per inch. Bottom hem shall be a continuous hem 3/8" without any gussets ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE 19 3-in-1 PARKA SAFETY-JACKET FOR SHERIFF S RANGE & E.V.O.C. STAFF 5.11 TACTICAL SPECIFICATIONS AND ESSENTIAL FEATURES FEATURES & BENEFITS: The 3-in-1 Parka 100% Nylon outer jacket, which is waterproof, windproof and breathable. Nylon also resists tears and abrasion. The outer shell has a fully waterproof, detachable hood and elasticized cuffs with hook and loop adjustment tabs. Lower back pocket. Removable ID panels on chest and back: Front Panel measures 5" W x 5 1/2" L. The back panel measures 12 1/2" W x 9 L The zip-in fleece jacket is wind resistant and can be worn on its own. Shoulder and elbows of the fleece jacket are reinforced with durable Nylon. Both the outer jacket and fleece inner jacket have 5.11 patented document chest pockets with our trademark Back-up- Belt System lining. These pockets can be used to stow gear such as handguns, handcuffs, flashlights and mace with our accessory pouches. Zippered hand pockets are lined with fleece to keep your hands warm and dry. Both the outer jacket and fleece lining jacket are cut to provide you with superior range of motion. Mic loops and side zippers for ventilation and access to a firearm. Built into each jacket's lining is an abrasion panel to increase the life of the garment. Page 45 of 59

46 FABRIC TYPE: Coat: 100% Nylon, Lining: 100% Nylon Taffeta Zip in Fleece Jacket: 100% Polyester Wind Resistant Fleece, Shoulder reinforcement: 100% Nylon Tasla STITCHING & FINISHING: 9-10 stitches per inch >Single needle stitching: Hood opening for drawcord, sleeve cuffs. > Edgestitch: Hood style line seam, hood neckline edge, collar, collar opening for hood stow away, collar chin guard, front placket, shoulder roll over seam, front pull out upper chest flange, all zippers, armholes, sleeve panel seams, front vertical body seams, hand warmer welt cut out edges, lower hem contrast join seam, hem line inner facing, sideseam zipper welts, sleeve cuffs, sleeve cuff tabs, sleeve articulation darts, back pull out flange. > 1/4" single needle topstitch: Front placket, front fly. CLOSURES: Zippers: Shell center front, Fleece center front, Shell & fleece lining pocket, Shell & fleece side seam, Shell and fleece hand pockets, Shell hood attachment, Shell ID panel access Hook & Loop: Shell ID panel to shell, Shell hood adjustment, Shell cuff tab adjustment, Shell and fleece document pockets. Snaps: Shell front fly visible at top and bottom (2), Shell front fly pre-set (4), Shell visible on side seam tabs (2) LABELS: Each jacket has a care label, size label, country of origin and fiber content label permanently attached to the garment. STOCK SIZES: XS-4XL COLOR: Range Red Page 46 of 59

47 ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE 20 TDU SHIRT Long Sleeve 5.11 TACTICAL FABRIC TYPE: 65% Polyester 35% Cotton Ripstop, twill SPECIFICATIONS AND ESSENTIAL FEATURES FEATURES: The TDU Shirt has been treated with Teflon fabric protector stain and soil resistance. Designed with 5.11 s patented hidden document pockets and bi-swing shoulders for a full range of motion. DESIGN: The long sleeve shirt shall incorporate hidden document pockets on the front chest. The shirt has a hidden placket with melamine buttons. The elbows are double layer with removable neoprene elbow pads. Bi-swing shoulder design allows for extra movement through the back shoulder area. The shirt bottom is a straight cut. The shirt is Teflon treated. The shirt comes with triple stitching and 28 bartacks for added strength. POCKET DESIGN: The two front chest pockets are flat with a Velcro closure. The two (2) hidden document pockets can hold large documents or necessary equipment. The pockets end at the arm/side seam in width and underneath the front chest pocket in length. They open approximately ½ from the edge of the placket and have two hook and loop strips to close the pocket opening. There are two (2) pencil pockets at the end of each sleeve. These pockets shall be 1 wide and 5 ½ long. LABEL: Shirt has a care label, size label, country of origin and fiber content label permanently attached to the garment. Page 47 of 59

48 ACCESSORIES: Buttons Melamine buttons that won t melt, burn or crack. It has Velcro hook & loop. COLOR: TDU Green STOCK SIZES: Shirts must be available in the following stock sizes: Men s: Small/Medium/Large/Extra-Large/2XL/3XL/4XL TECHNICAL DATA and PERFORMANCE STANDARD TEST PERFORMANCE USA STANDARD EUROPEAN STANDARD Shrinkage 3% length x 3% width AATCC 135/150 BS EN 25077/BS EN (Dimensional Stability to Washing) Colorfastness Washing Color Change = 4 Color Staining = 4 Self/Cross-Staining = 5 Water Color Change = 4 Color Staining = 4 Self/Cross-Staining = 5 Perspiration Color Change = 4 Color Staining = 4 Self/Cross-Staining = 5 AATCC 61 (40C) AATCC 107 AATCC 15 EN ISO 105C06 EN ISO 105 EO1 EN ISO 105E04 Light 4 AATCC 16E 20 AFU EN ISO 105 B02 Page 48 of 59

49 Up To Grade 4 Crocking/Rubbing Dry = 4 Strength Properties Wet = 3 AATCC 8/116 EN ISO 105 X12 Seam Strength tchability 30 lbs ASTM D 1683 ENISO Tensile Strength 35 lbs ASTM D 5034 ENISO Tear Strength 2.5 lbs ASTM D 1424 EN ISO SOIL and Stain Release 4 AATCC Water Repellency 4 AATCC 22 EN Pilling Resistance 4 ASTM D 3512 EN ISO Fading Resistance/Durability after 20 washes Color Change = 4.0 AATCC 150 EN ISO ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE 21 MEN S TDU PANTS 5.11 TACTICAL SPECIFICATIONS AND ESSENTIAL FEATURES Page 49 of 59

50 FABRIC & FINISHING: Main Body: 65% Polyester, 35% cotton; tear- resistant Ripstop; with HR Teflon water resistant finish. Pocketing: 70% Polyester 30% Cotton, 3.2 oz, tightly woven poplin FEATURES & BENEFITS: Self adjusting tunnel waist; Deep front pockets; Large pleated cargo pockets with bellows on sides and 2-compartment pockets with BBS feature inside; Back Pockets with flaps. The pants have double knees of self- fabric, removable 6mm Neoprene knee pad inserts, and a double seat of self fabric. Leg openings have removable draw cords. POCKETS: Front Pocket openings have self fabric facings and extra reinforcement on knife clipping area. Pocket opening and side seam intersections are firmly back tacked. Pocket bags are made of durable Poly/Cotton blend and they are extra deep. Pocket bags are finished clean inside the pant and double stitched for heavy duty. Cargo pockets have large flaps and Velcro closure that is designed to reach even when pockets are full. Divided pockets inside have double function: small items fit inside and several types of rigs attach to Velcro loop fabric on the face side. Pleats and bellows camouflage the exact nature of the items on the rigs. Back Pockets have single welts and generous size flaps with two-velcro closure on both sides. Pocket bags are deep, clean finished inside and double stitched. SEAMS AND STITCHING: Seams are durable with 10 stitches per inch and extra heavy 5-thread construction. Top Stitchings are non-raveling lock stitchings. Side seams, seat seam and front rise have tree-needle top stitching. Crotch point is bar tacked. Fly outline, hand pocket openings, all pocket flaps, knee patches and seat patch have double needle top stitchings. Cargo pockets are attached with double needle top stitching. Belt loops are bar tacked on all corners. Cargo pocket openings are bar tacked and flaps are cross bar tacked. Back pocket openings are bar tacked. All Velcro pieces are attached with box stitching. Hem draw cord is tacked to inseam so that it will not slip out; the tack is removable. LABELS: The woven logo label, care label, size label, country of origin label and fiber content label are permanently attached to the pants. CLOSURES: Closures are high quality, proven brand name products. Fly zipper is metallic YKK zipper with auto lock slider. Waist snap is metallic PRYM snaps with extra strong grip. Inside fly button is non-burning, non-melting, non-cracking Melamine button, and it is cross tacked. STOCK SIZES: The pants are available in the following sizes: Page 50 of 59

51 Size XS S M L XL 2XL 3XL 4XL 5XL 6XL 23 1/2 - Waist 27 Rang e 27 ½ ½ ½ ½ ½ ½ ½ ½ -59 ½ -63 COLOR: TDU Green Inseams Short 29 ½ Regular 32 ½ Long 35 ½ X-Long 38 ½ Unhemmed 39 ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE 22 JACKET RAID Unlined, Long Sleeve Color: Black Buttons: Black Snap Auburn / Hartwell 101-A1 STYLE: Unlined Long Sleeve SPECIFICATIONS AND ESSENTIAL FEATURES BUTTONS: Black snap COLOR: Black Page 51 of 59

52 ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE 23 UNISEX TROUSERS SHERIFF S CADET TACT SQUAD DC72GY STYLE: Tact Squad Style #DC72 DC72NE DC72BE DC72BRE DC72HE FABRIC: 11.5 to 12 ounce per linear yard, gabardine weave 100% texturized polyester. SPECIFICATIONS AND ESSENTIAL FEATURES COLOR: Dark Navy POCKETS: The front pocket opening will be a minimum 6½" and be 6" deep from the bottom of the opening. Shall be made on a uniform pattern, having a plain front with quarter top front pockets, ⅞" belt loops and two back pockets. Pockets shall be stitched, turned, and restitched. The inside front pocket facing shall be a separate piece of self material finishing no less than 1¼" wide. The back pockets will have a minimum opening of 5½" and be 6" deep. They shall be made with a Reese PW automatic machine and finished on the outside with an exposed top and bottom cord. The left pocket shall have a tab to button. The front pockets shall each have a straight bartack and each back pocket shall be bartacked with a triangular bartacking machine. POCKETING: All pocketing shall be black 65% Polyester/35% Cotton with a minimum thread count of 68 x 54, the weight shall be 2.60 yards/lb. WAISTBAND: Must be of AT-EASE WAISTBAND construction for superior comfort and performance. The curtain, attached with a rocap machine, shall be made of black, bias-cut, cotton blended twill and shall have two continuous parallel 3/16" wide silicone bands for shirt retention. The inside of the waistband shall be made from a stretch, breathable non-woven material for support. A 3/4" strip of a similar breathable stretch material shall be sewn into the waistband along the top for non-roll edge control. The finished waistband shall be 2" wide and shall be closed with a crush-proof double hook and eye, the eyes being bartacked for stability. The finished waistband shall be set on and shall be stitched below the lower edge through the outer fabric and the waistband curtain. INNER FLY/CROTCH: Page 52 of 59

53 The right fly and front crotch linings shall be the same fabric and color as the waistband curtain. There shall be a nonwoven interlining sewn to the fly to give additional stability and strength to the fly. The right fly lining shall be sewn to the left fly below the zipper and continue centered on the seam across the inseam and end 1" onto the backseam. A separate french fly made of the outer fabric shall be sewn to the inside right fly. There shall be a triple strength crotch reinforcement to prevent seam failure in the crotch and inseam area. The crotch shall be secured with two rows of stitching. One row is to be on the inside of the trouser, then turned and an additional row to be sewn on the outside of trouser. ZIPPER: The trousers shall be closed with a brass memory lock zipper and have a brass bottom stop at the base of the zipper chain. A straight bartack shall be sewn through from the outside of the garment to the inside at the bottom of the fly. It shall be sewn through the zipper tape, the right and left fly and the right fly lining. The right and left fly shall be joined by an additional bartack located below the bottom zipper stop on the inside of the trouser. BELT LOOPS: There should be a minimum of 7 lined belt loops. Each loop is to be ⅞" wide of double thickness, with stitching on the face side ⅜" from each edge. Except for the back loop which shall be tacked on, all loops shall be sewn into the bottom of the waistband and into the rocap. They shall accommodate a 1⅝" belt. SEAMING: The entire trouser is to be seamed with Polyester core or 100% Polyester spun thread. The seat seam shall be stitched with a tandem needle seat seaming machine. LABELS: The trouser shall have a sewn-in label giving care instructions and an outside waistband label which shall be marked with lot number, size, fiber content, and cut number. FINISHING AND PRESSING: All loose threads shall be removed. Trousers must be pressed completely and properly with side seam, inseam, and seat seam pressed open. SIZE SCALE: o o o o o o o o o o o o o o o o o o o o o o Page 53 of 59

54 ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE 24 TROUSERS SAN MATEO POLICE ACADEMY RECRUIT TACT SQUAD DC72N STYLE: Tact Squad Style #DC72 DC72NE DC72BE DC72BRE DC72HE FABRIC: 11.5 to 12 ounce per linear yard, gabardine weave 100% texturized polyester. SPECIFICATIONS AND ESSENTIAL FEATURES COLOR: LAPD Navy Blue POCKETS: The front pocket opening will be a minimum 6½" and be 6" deep from the bottom of the opening. Shall be made on a uniform pattern, having a plain front with quarter top front pockets, ⅞" belt loops and two back pockets. Pockets shall be stitched, turned, and restitched. The inside front pocket facing shall be a separate piece of self material finishing no less than 1¼" wide. The back pockets will have a minimum opening of 5½" and be 6" deep. They shall be made with a Reese PW automatic machine and finished on the outside with an exposed top and bottom cord. The left pocket shall have a tab to button. The front pockets shall each have a straight bartack and each back pocket shall be bartacked with a triangular bartacking machine. POCKETING: All pocketing shall be black 65% Polyester/35% Cotton with a minimum thread count of 68 x 54, the weight shall be 2.60 yards/lb. WAISTBAND: Must be of AT-EASE WAISTBAND construction for superior comfort and performance. The curtain, attached with a rocap machine, shall be made of black, bias-cut, cotton blended twill and shall have two continuous parallel 3/16" wide silicone bands for shirt retention. The inside of the waistband shall be made from a stretch, breathable non-woven material for support. A 3/4" strip of a similar breathable stretch material shall be sewn into the waistband along the top for non-roll edge control. The finished waistband shall be 2" wide and shall be closed with a crush-proof double hook and eye, the eyes being bartacked for stability. The finished waistband shall be set on and shall be stitched below the lower edge through the outer fabric and the waistband curtain. Page 54 of 59