SITCO ANTENNAS ASSEMBLY INSTRUCTION FOR HIGH BAND VHF QUAD END MOUNT
|
|
- Clara Parsons
- 5 years ago
- Views:
Transcription
1 S ANENNAS ASSEMBLY NSRUN FR HGH BAND VHF QUAD END MUN N.E. Marx St, Ph: (503) P.. Box 20456, Fax: (503) Portland, R sitco@simplicitytool.com Website: Rev. 02-A
2 S ANENNAS 1.1. BLL F MAERALS: a. wo cartons, each containing: b. ne carton containing: DESRPN QY Antennas 2 Set quad frame members (7 pc s) 1 set (will be in one of two cartons) Stacking rod (2 pc s) 1 set (will be in one of four cartons) Braces 2 able harness: 1 (will be in one of the two cartons) Assembly instruction 1 (will be in one of two cartons) DESRPN Hardware pack No containing: a. Bolt 5/16-1 x 3-1/2 b. Screw10-24 x 1-1/4 c. Fiber nut d. Nut 5/16 e. Flat washer 5/16 f. Lock washer 5/16 a. Single clamps a. Frame bolt 5/16-1 x 5-1/2 b. Hex nuts 5/16 c. Flat washer 5/16 d. Lock washer 5/16 e. Bolt 1/4-20 x 2-3/4 f. Flat washer 1/4 g. Lock washer 1/4 h. Bolt 1/4-20 x 2-1/4 i. U-bolt j. Hex nut 1/4 QY otal quantity of cartons is three. 2-
3 S ANENNAS 1.2. QUAD FRAME ASSEMBLY: a. A frame consists of four vertical members and three horizontal members. Assemble horizontal and vertical members per Figure 1. Be sure to only finger tighten the bolts holding the frame together until the antenna booms have been tightened to avoid hole alignment problems. b. List of parts used in frame assembly: EM DESRPN QY FUND N 2-1 Vertical frame member Horizontal frame member 3 Frame Box 2-3 Single clamps Frame bolt 5/16-1x5-1/ Hex nuts 5/16 6 Hardware box 2-6 Flat washer 5/ Lock washer 5/ BRAE MUNNG PNS ANENNA MUN PNS ANENNA MUN PNS Figure 1 3-
4 S ANENNAS 1.3. ANENNA MUNNG AND BRANG a. Four antennas mount to the quad frame through mounting holes shown in Figure 2. For antenna mounting position, refer to Figure 5, page 7-. n staggered quads, the longer booms should be mounted to the bottom of the frame, and the shorter booms to the top of the frame. NE: Be sure all baluns are pointed downward for phase coherence in the array. b. Braces are attached as shown in Figure 2. Braces from the upper two bays come down to the middle horizontal frame member and braces from the lower bays come up to the middle horizontal frame member. c. List of antenna and brace hardware: EM DESRPN QY FUND N 3-1 Antenna Brace Frame box 3-3 Single clamp 3-4 Bolt 5/16-1 x 3-1/2 3-5 Bolt 1/4-20 x 2-3/ Screw x 1-1/4 Hardware 3-7 Kep nut box 3- Nut 1/ Flat washer 1/ Lock washer 1/4 Step 1: Mount antennas to assembled quad frame using 5/16-1 x 3-1/2 bolts, flat washer and single clamps as in Figure 5. Step 2: Mount braces to horizontal frame member using 1/4-20 x 1-3/4 bolts, flat washer, lock washer and nut. n some models only one hole will be available to mount both braces to frame. Step 3: Assemble braces to antenna with 1/4-20 x 2-1/4 screw and kep nut. Step 4: nstall the vertical spacing rods through the booms. hese rods should extend app. 1/2 above the upper boom and 1/2 below the lower boom. heck to make sure that the vertical boom spacing is the same at the front and at the end of the array. 4-
5 S ANENNAS NE: ighten all bolts securely. Do not over tighten, as this will compress the clamps and distort the bolts and antenna alignment. Figure 2 5-
6 S ANENNAS 1.4. MAS MUNNG a. Mount quad array as in Figure 4. Standard hardware is for 1-1/2.D. mast. versize hardware for 2, 2-1/2, 3-1/2 and 4-1/2.D. masts are available. See Figure 6 page -. b. List of mast mount hardware: EM DESRPN QY FUND N 4-1 Single clamp U-bolt Hex nut ¼ Flat washer ¼ Lock washer ¼ 6 Hardware box HRZNAL FRAME MEMBER MAS/WER, LEG (N SUPPLED) Figure 4 6-
7 S ANENNAS 1.5. FULL ASSEMBLY F ANENNA a. omplete list of hardware for array: EM DESRPN QY 5-1 Bolt ¼-20 x 2-3/ Flat washer 1/ Lock washer 1/ Hex nut 1/ Bolt 5/16-1 x 5-1/ Flat washer 5/ Lock washer 5/16x1 5- Hex nut 5/16x1 5-9 Single clamp U-Bolt 3 Figure 5 7-
8 S ANENNAS 1.6. NSALLAN F PHASNG HARNESS a. Attach the harness such that the two antennas an each side are combined and then the two sides (the harness forms the shape of the letter H ). n staggered quads, attach the longer feed lines to the lower (longer) booms, and the shorter lines to the upper (shorter) booms NSALLAN FR VERSZE MAS (option) a. For oversize mast / tower leg (2, 2-1/2, 3-1/2 and 4-1/2 ) there would be added sixth carton with hardware. For installation see Figure 6. EM DESRPN QY FUND N 7-1 Flat Plate U-bolt 7-3 Hex nut 16 versize box 7-4 Flat washer Lock washer 16 Figure 6 -
SITCO ANTENNAS ASSEMBLY INSTRUCTION FOR STAGGER STACK VHF QUAD
S ANENNAS ASSEMBLY NSRUN FR SAGGER SAK VHF QUAD 10330 N.E. Marx St, Ph: (503) 253-2000 P.. Box 20456, Fax: (503) 253-2009 Portland, R 97220 E-mail: sitco@simplicitytool.com Website: www.simplicitytool.com
More informationSITCO ANTENNAS ASSEMBLY INSTRUCTION FOR VHF STAGGER STACK ARRAY END MOUNTED. Website: Rev. 02-A T C O
S ANENNAS ASSEMBLY NSRUN FR VHF SAGGER SAK ARRAY END MUNED 10330 N.E. Marx St, Ph: (503) 253-2000 P.. Box 20456, Fax: (503) 253-2009 Portland, R 97220 E-mail: sitco@simplicitytool.com Website: www.simplicitytool.com
More informationMOUNTING INSTRUCTIONS
Standard Mounting Bracket Tilting Bracket* Mounting example Right side for upper tilt from 0 to 20 20 Spare parts: p/n SA197 Materials: extruded aluminum Hardware: stainless & zinc plated steel Dimensions
More informationINSTRUCTION MANUAL. Specifications Mechanical. 1 5/8 to 2 1/16 O.D. (41mm to 52mm)
308 Industrial Park Road Starkville, MS 39759 USA Ph: (662) 323-9538 FAX: (662) 323- General Description Model VB-25FM 2-Meter 5 Elements Beam INSTRUCTION MANUAL This antenna is a 5-element, 2-meter beam
More informationKU-BAND FEED INSTALLATION OMT INTERFACE
Revision D April 22, 2016 Assembly Manual KU-BAND FEED INSTALLATION OMT INTERFACE General Dynamics SATCOM Technologies 1700 Cable Drive NE Conover NC 28613 USA Phone 770-689-2040 www.gdsatcom.com KU-BAND
More informationM2 Antenna Systems, Inc. Model No: 2M7
M2 Antenna Systems, Inc. Model No: 2M7 SPECIFICATIONS: Model... 2M7 Frequency Range... 144 To 148 MHz *Gain... 12.3 dbi Front to back... 20 db Typical Beamwidth... E=43 H=50 Feed type... T Match Feed Impedance....
More informationM2 Antenna Systems, Inc. Model No: HFTB2MXP X2-3K
M2 Antenna Systems, Inc. Model No: HFTB2MXP28-32-2X2-3K FRONT OF SYSTEM REAR OF SYSTEM SPECIFICATIONS: Model... HFTB2MXP28-32-2X2-3K Band... 2M Antenna... 2MXP28-32 T-Brace... Y Cross Boom Dia... 3.0 Wind
More informationInstallation Guide. Mounting Kit for Mounting Philips Avalon CTS Cordless Fetal Transducer System on Wall, 2'' Post, Rail, or Slide-on Mounting Plate
Installation Guide Mounting Kit for Mounting Philips Avalon CTS Cordless Fetal Transducer System on Wall, 2'' Post, Rail, or Slide-on Mounting Plate The purpose of this guide is to: 1. Describe mounting
More informationFor additional assistance call
The following pages will help guide you through the process of assembling your new 48 custom prize wheel. Choose an assembly area with plenty of room to lay your pieces on the floor and also a bench or
More informationSTRUCTURAL HOLDING, F150 TOOL BOARD, AND CART ASSEMBLY
STRUCTURAL HOLDING, F150 TOOL BOARD, AND CART ASSEMBLY 150006 2014 Chief Automotive Technologies CO9110.1 Rev. A 12/19/14 F150 Structural Holding Tool Board Cart Step 1: Caster Assembly. A.) Assemble 5
More informationD3976 RECESSED EXIT INSTALLATION INSTRUCTIONS
PACKAGE CONTENTS PRODUCT MUST BE INSTALLED ACCORDING TO ALL APPLICABLE BUILDING AND LIFE SAFETY CODES TEMPLATE INSTALLATION INSTRUCTIONS STRIKE HAND TOOL 5/32 HEX KEY ROD END CAPS EXIT DEVICE CRANK ARM
More informationM2 Antenna Systems, Inc. Model No: 2M4
M2 Antenna Systems, Inc. Model No: 2M4 SPECIFICATIONS: Model... 2M4 Frequency Range... 144 To 148 MHz *Gain... 9.6 dbi Front to back... 20 db Typical Beamwidth... E=54 H=74 Feed type... T Match Feed Impedance....
More informationMHz. ANT150D, D3, D6-9 DIPOLE AND DIPOLE ARRAY 1 TO 9 dbd
138-174 MHz ANTD, D3, D6-9 DIPOLE AND DIPOLE ARRAY 1 TO 9 dbd The Telewave ANTD series consists of single, dual, and 4-element di pole array antennas with a precision phasing harness for optimum per formance.
More informationM2 Antenna Systems, Inc. Model No: 450CP26
M2 Antenna Systems, Inc. Model No: 450CP26 SPECIFICATIONS: Model... 450CP26 Frequency Range... 445 To 455 mhz *Gain... 16.5 dbi Front to back... 21 db Typical Beamwidth... 30 Circular Feed type... T Match
More informationM2 Antenna Systems, Inc. Model No: 2M5WL
M2 Antenna Systems, Inc. Model No: 2M5WL SPECIFICATIONS: Model... 2M5WL Frequency Range... 144 To 148 MHz *Gain... 16.84 dbi Front to back... 22 db Typical Beamwidth... E=26 H=29 Feed type... T Match Feed
More informationM2 Antenna Systems, Inc. Model No: HFTB2MXP X2-1K
M2 Antenna Systems, Inc. Model No: HFTB2MXP28-32-2X2-1K FRONT OF SYSTEM REAR OF SYSTEM SPECIFICATIONS: Model... HFTB2MXP28-32-2X2-1K Band... 2M Antenna... 2MXP28-32 T-Brace... Y Cross Boom Dia... 3.0 Wind
More informationModel VB-23FM 2-Meter 3-Element Beam
308 Industrial Park Road Starkville, MS 39759 USA Ph: (662) 323-9538 FAX: (662) Model VB-23FM 2-Meter 3-Element Beam [ INSTRUCTION MANUAL Figure 1 Overall View and Boom Detail GENERAL DESCRIPTION This
More informationGlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationM2 Antenna Systems, Inc. Model No: 436CP30
M2 Antenna Systems, Inc. Model No: 436CP30 SPECIFICATIONS: Model... 436CP30 Frequency Range... 432 To 440 MHz *Gain... 15.50 dbic Front to back... 18 db Typical Elipticity... 1.5 db Typical Beamwidth...
More informationM2 Antenna Systems, Inc. Model No: 435XP50
M2 Antenna Systems, Inc. Model No: 435XP50 SPECIFICATIONS: Model... 435XP50 Frequency Range... 430 To 436 MHz *Gain... 19.2 dbi Front to back... 22 db Typical Cross pol. isolation... >20 db Typical Beamwidth...
More informationThis manual will aid in the assembly of the FireBall V90 and FireBall X90. The assembly of both machines will be identical, unless specified.
This manual will aid in the assembly of the FireBall V90 and FireBall X90. The assembly of both machines will be identical, unless specified. Step #1 Lay all parts out to verify quantities. (2) 2 x 25-1/4
More informationGlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationM2 Antenna Systems, Inc. Model No: FGHFTB2MXP202X2
M2 Antenna Systems, Inc. Model No: FGHFTB2MXP202X2 FRONT OF SYSTEM REAR OF SYSTEM SPECIFICATIONS: Model... HFTB2MXP20-2X2 Band... 2M Antenna... 2MXP20 T-Brace... Y Cross Boom Dia... 3.0 Wind Load w/o Ant.....
More informationM2 Antenna Systems, Inc. Model No: 2MCP22
M2 Antenna Systems, Inc. Model No: 2MCP22 SPECIFICATIONS: Model... 2MCP22 Frequency Range... 144 To 148 MHz *Gain... 14.39 dbic Front to back... 25 db Typical Elipticity... >3db Beamwidth... 38 Feed type...
More informationSS1062, SS10621 & SS10621E Free Standing PWC & Fishing Boat Hoist SS1062 SS10621 SS10621E
SS1062, SS10621 & SS10621E Free Standing PWC & Fishing Boat Hoist SS1062 SS10621 SS10621E Midwest Industries, Inc. Page 1 Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003231 REV A 1/25/05 Bundles
More informationM2 Antenna Systems, Inc. Model No: 20M5LD
M2 Antenna Systems, Inc. Model No: 20M5LD SPECIFICATIONS: Model... 20M5LD Frequency Range... 14.0 14.350 MHz *Gain (Full Band)... 10.2 dbi Typical Front to back... 23 db Typical Beamwidth... E=50 / H=66
More informationM2 Antenna Systems, Inc. Model No: 450CP34
M2 Antenna Systems, Inc. Model No: 450CP34 SPECIFICATIONS: Model... 450CP34 Frequency Range... 435 To 455 mhz *Gain... 16.0 dbi Front to back... 22 db Typical Beamwidth... 28 Circular Feed type... T Match
More informationInstallation Guide Flat Panel Antenna Mounting Kit For
Installation Guide Flat Panel Antenna Mounting Kit For 103670-1 495R Billerica Ave. North Billerica, MA 01862 USA Tel (978)459-8800 fax (978)459-3310 / 8814 Email: sales@radiowaves.com www.radiowaves.com
More informationM2 Antenna Systems, Inc. Model No:
M2 Antenna Systems, Inc. Model No: 400-600-10 SPECIFICATIONS: Model... 400-600-10 Frequency Range... 390 To 650 MHz *Gain... 12 To 13 dbic Front to back... 20 db Nominal Beamwidth... 46 Nominal Feed Impedance....
More informationSINCE 1922 P UBLICATION N O
SINCE 1922 GARED SPORTS MICRO-Z SET-UP INSTRUCTIONS VERY IMPORTANT! READ INSTRUCTIONS CAREFULLY AND FOLLOW STEP BY STEP SET-UP PROCEDURE P UBLICATION N O. 5 5 1 7 5 2 9 1 6 Recommended tools and accessories.
More informationSole Fitness E95 Elliptical Trainer TurnKey Delivery and Setup Training
Sole Fitness E95 Elliptical Trainer TurnKey Delivery and Setup Training Delivery Requirements Ground delivery Inside delivery to customer-specified location Unpack and assemble machine, and remove packing
More informationASSEMBLY INSTRUCTIONS Last Updated
ASSEMBLY INSTRUCTIONS Last Updated 05.08.08 5 & 10 Row Bleacher Instructions for all bleacher lengths. Guardrail and toe board installation included. 90653 9 Long 5 Row Bleacher 90654 15 Long 5 Row Bleacher
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationM2 Antenna Systems, Inc. Model No: 456CP34
M2 Antenna Systems, Inc. Model No: 456CP34 SPECIFICATIONS: Model... 456CP34 Frequency Range... 435 To 470 mhz *Gain... 16.0 dbi Front to back... 23 db Typical Beamwidth... 30 Circular Feed type... T Match
More informationAssembly Instructions
Laminate/Phenolic & 1 Pc Butcherblock Tops Before you begin, please make sure all parts and proper quantities are included. (See on next page) Any parts damaged during shipment must be reported within
More informationO-Sullivan King 4 Poster Bed O-Sullivan Queen 4 Poster Bed Parts and Hardware List
Parts and Hardware List A. Left Headboard Post 1 pc B. Right Headboard Post 1 pc C. Left Footboard Post 1 pc D. Right Footboard Post 1 pc E. Headboard Panel 1 pc F. Footboard Rail 1 pc. Spindles 4 pcs
More information2-PIECE STAIRWAY ASSEMBLY
REVISED 2/12/15 2-PIECE STAIRWAY ASSEMBLY STEP 1: LAY OUT THE RIGHT AND LEFT SIDE TOP AND BOTTOM RISER PANELS AS SHOWN IN FIGURE 1. BOLT THE SPLICE PLATE (#15114C for OSHA F SERIES; #15412C for BOCA U
More informationTHIS SHOULD TWEAK YOUR IMAGINATION
10-27-05 THIS SHOULD TWEAK YOUR IMAGINATION SPECIFICATIONS FOR SINGLE ANTENNA MODEL NUMBER... 432EME-12 FREQUENCY... 430-436 MHz GAIN... 14.4 dbd FRONT TO BACK... 23 db VSWR... 1.2:1 TYPICAL BEAMWIDTH...
More informationUser Instructions Multiline Otter Scoreboard Caddy Assembly
List of parts: User Instructions Multiline Otter Scoreboard Caddy Assembly Single Caddy Double Caddy 1 1 Base assembly with attached wheels 2 4 1 1 2 4 4 8 10 20 12 Uprights (60 or 74 aluminum extrusion)
More informationPack Mount Instructions:
Pack Mount Instructions: STEP 1 Mounting upright base to desired surface If mounting to a surface with an accessible backside (such as a thin walled container): Option 1 Discard the Round Mounting Disk
More informationSide-of-Pole Mount for 4 Modules (SPM4) For Module Type D
Side-of-Pole Mount for 4 Modules (SPM4) For Module Type D ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A PCN 060712-7 Side-of-Pole Mount for 4 Modules (SPM4) For Module Type
More informationLIGHT BEAM ANTENNA MaxRange Antenna Series Assembly Instructions MaxRange Plus Digital / High Definition Television Antennas
LIGHT BEAM ANTENNA MaxRange Antenna Series Assembly Instructions MaxRange Plus Digital / High Definition Television Antennas Assembly Instructions 1 MaxRange Plus Antenna These instructions will lead you
More informationINSTRUCTION MANUAL ORDER NO. V3R MODEL V3R. Collinear Gain Vertical for MHz
ORDER NO. V3R MODEL V3R Collinear Gain Vertical for 216-225 MHz INSTRUCTION MANUAL General Description The new Hy-Gain V3R VHF antenna is a collinear 5/8-wave omnidirectional vertical antenna for the 216-225
More informationM2 Antenna Systems, Inc. Model No: 20M6-125
M2 Antenna Systems, Inc. Model No: 20M6-125 SPECIFICATIONS: Model... 20M6-125 Frequency Range... 14.0 14.350 MHz *Gain, (FS) / Over gnd... 11.19dBi / 16.6dBi @70 Front to back... 25 db Typical Beamwidth...
More informationM2 Antenna Systems, Inc. Model No: 10-30LP8
M2 Antenna Systems, Inc. Model No: 10-30LP8 SPECIFICATIONS: Model... 10-30LP8 Frequency Range... 10-30 MHz Continuous *Gain free space / 65... 5.2 dbi / 10.5 dbi 10-30 Front to back... 15 db 10-30 MHz
More informationPRE-ENGINEERED HORSE STALL SYSTEMS SDFD SLIDING DOOR c/w FOLD-DOWN GRILL. & Assembly. Installation Instructions
PRE-ENGINEERED HORSE STALL SYSTEMS 4800 SDFD SLIDING DOOR c/w FOLD-DOWN GRILL & Assembly Installation Instructions 4800 SDFD Sliding Door c/w Fold-Down Grill Components - 1 3 /4" x 2" x 88" channels (2)
More informationMAG-CONV Basic, 48, 48R & Midline Front Mount
Parts Required: Tools Used: Mag Wheels Brakes Brake Rods Mounting Bracket Anti Tippers 7/16" Wrench Screw Driver Rubber Mallet 5/8 Wrench 5mm Allen Wrench Step Execution Figures 1 Remove front 5" total
More informationINSTALLATION INSTRUCTIONS
Do not attempt to install this product on any vehicle other than the one it is designed for and listed above! Parts List 10 3/8 X 1 1/4 Hex Bolt 10 3/8 Lock Washer 4 3/8 Hex Nut 4 3/8 Flat Washer 2 3169)
More informationF l a t S c r e e n A R M S I n s t a l l a t i o n
ITEM NUMBERS (1) #TOACAORG16 (2) #TOACAORG20 (3) #TOACATRP24 (4) #TOACATRP30 (5) #TOACATRPDS (6) #TOACATRPSS TOOLS REQUIRED (1) 3/8 Wrench (not provided) (2) Phillips head screwdriver (not provided) (1)
More informationINSTALLATION INSTRUCTIONS FOR FRONT CASTING DECK RAIL Ranger
INSTALLATION INSTRUCTIONS FOR FRONT CASTING DECK RAIL Ranger TOOLS REQUIRED FOR INSTALLATION: Drill motor, (1) 5/16 inch drill bit, (1) 13/64 drill bit, (1) 3/16 inch hex wrench (1) 3/32 inch hex wrench.
More informationInstructions and Parts List DR-12N Martin House
Form 36-99 Instructions and Parts List DR-N Martin House Note: It is necessary to install a post before house is put up, but the house can be assembled at any time. House parts Check parts against this
More informationHatch Whiteboard: Portable Stand Installation Instructions
Hatch Whiteboard: Portable Stand Installation Instructions Remove Projector Wall Plate 1. Open the wall mount for the projector. 2. Remove the shipping screw from the front center of the mount arm. 1 P
More informationM2 Antenna Systems, Inc. Model No: KT31WARC
M2 Antenna Systems, Inc. Model No: KT31WARC SPECIFICATIONS: Model... KT31WARC Frequency Range... 10.1-10.15 MHz **Selectable Frequency Range... 14.0-14.35 MHz **Selectable... (175 KHz / 2:1 VSWR Nominal)
More informationC PART LIST HARDWARE LIST. Kitchen Cart IMPORTANT NOTE
88 9200 006C Kitchen Cart IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the parts. We have taken
More informationInstallation Instructions for Solar Snow Pad (SSP-T-3)
Installation Instructions for Solar Snow Pad (SSP-T-3) Warning- Do not use this product on solar arrays where the calculated array snow loads exceed 50 pounds per square foot (psf). Most solar panels are
More informationSEAT-831. Seat Box Kit. Club Car Precedent. Installation Instructions
SEAT-831 Seat Box Kit Club Car Precedent Installation Instructions Contents of SEAT-831 Seat Box Kit: a (1 ea.) Seat Box Platform b (1 ea.) Front Seat Box Plate c (1 ea.) Foot Plate d (1 ea.) Tailgate
More informationINSTALLATION INSTRUCTIONS 1PC FRONT BUMPER JEEP JK WRANGLER
INSTALLATION INSTRUCTIONS PARTS LIST: 1 1PC Bumper 2 8mm x 25mm Hex Bolts 1 Bull Nose Hoop 2 8mm x 16mm Hex Bolts 1 Fairlead Mounting Bracket 6 8mm x 24mm x 2mm Flat Washers 8 12mm x 35mm Hex Bolts 4 8mm
More informationModel 6025 Single-Boom
Log Periodic FM Broadcast Antenna Model 6025 Single-Boom Instruction Manual Installation, Operation, & Maintenance Congratulations! Thank you for purchasing one of the finest FM broadcast antennas on the
More informationM2 Antenna Systems, Inc. Model No: HFTB6MXP20-2X2
M2 Antenna Systems, Inc. Model No: HFTB6MXP20-2X2 FRONT OF SYSTEM REAR OF SYSTEM SPECIFICATIONS: Model... HFTB6MXP20-2X2 Band... 6M Antenna... 6MXP20 T-Brace... Y Cross Boom Dia... 4.5 Wind Load w/o Ant.....
More informationCalf-Tel Pen System Assembly Instructions
Calf-Tel Pen System Assembly Instructions (Instructions work for 4, 6, and the 7 Pen Systems) 1 ASSEMBLY OF PEN FRONT AND WALLS START THE ASSEMBLY BY LINING UP THE TWO UNI-DIRECTIONAL ARROWS IN THE TOP,
More information75 cm ODU (VS1300 with the SurfBeam2 TRIA) Assembly Job Aid
Summary This Job Aid covers: Verify AZ/EL Assembly Alignment Antenna Back Bracket Assembly TRIA, TRIA Bracket, and Boom Arm Assembly This Job Aid supports all Technician audiences. This job aid covers
More informationPACKING LIST MACO V-5000
PACKING LIST MACO V-5000 PART QTY O.D. SIZE LENGTH DESCRIPTION CHECKLIST T47P 4 5/8.050 36 Aluminum Tubing _ T43P 1 7/8.050 48 Aluminum Tubing _ T18P 1 3/4.050 48 Aluminum Tubing _ T15P 1 5/8.050 48 Aluminum
More informationSide-of-Pole Mount for 4 Modules (SPM4) For Module Type B ASSEMBLY INSTRUCTIONS. step-by-step assembly and installation
Side-of-Pole Mount for 4 Modules (SPM4) For Module Type B ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A SP3358-2 PCN 060712-5 Side-of-Pole Mount for 4 Modules (SPM4) For
More information#916 CLASSIC 16 GUN CABINET ASSEMBLY INSTRUCTIONS
Thank you for purchasing this quality product. A list of PARTS and INSTRUCTIONS is included to assist you. Unpack and identify all parts included on the Parts List and Hardware List. If parts are missing,
More informationStar Trac Turbo Trainer Assembly & Setup
Star Trac Turbo Trainer Use the following procedures to unpack and assemble your Turbo Trainer manufactured by Star Trac. UNPACKING AND PARTS LIST Position the shipping carton so the Heavy End logo is
More informationCushcraft. Amateur Radio Antennas DB-46M8EL. Dual band 6 and 4 Meter, 8 Element Beam Antenna INSTRUCTION MANUAL
Cushcraft Amateur Radio Antennas DB-46M8EL Dual band 6 and 4 Meter, 8 Element Beam Antenna INSTRUCTION MANUAL CAUTION: Read All Instructions Before Operating Equipment VERSION 1B Cushcraft Amateur Radio
More informationLCD/Plasma Mount Manual
LCD/Plasma Mount Manual Product Overview: Thank you for your Cheetah Mount purchase. All Cheetah Mounts are designed to provide excellent function, high quality, easy installation and stylish appearance.
More informationInstallation Instructions - Model V4JSD 1
Installation Instructions - Model V4JSD 1 Support Assemblies: Parts list: (Note see enclosed cut sheet for quantities and dimensional information) A vertical structural member (1 ½ x 1 ½ modular frame)
More informationASSEMBLY INSTRUCTIONS
Universal Top-of-Pole Mount 8 Modules (UTPM8) Module Type G ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A PCN 022714-1 Universal Top-of-Pole Mount 8 Modules (UTPM8) for
More informationElliptical Unpacking and Installation Instructions
Elliptical Unpacking and Installation Instructions Use these instructions for the following Ellipticals: ClubStride 5100-LE Receiving When the carrier delivers your order, verify that the number of items
More information32 Gallon Perforated Square Receptacle
32 Gallon Perforated Square Receptacle 992-031 24 5/" 24 5/" 39 1/2" 30 1/2" ITEM NO. PART NUMBER DESCRIPTION QTY. 1 653-006 Receptacle Base 1 2 653-045 32 Gallon Perforated Side 4 3 653-011 Arch Lid 1
More informationASSEMBLY INSTRUCTIONS RIGHT & LEFT HAND "J" TABLE
ASSEMBLY INSTRUCTIONS RIGHT & LEFT HAND "J" TABLE (1) COMPONENT LIST FOR RIGHT & LEFT HAND "J" TABLE NOTE: Please count and inspect all pieces before disposing of any carton or packing materials. 24" x
More informationASSEMBLY INSTRUCTIONS
Universal Top-of-Pole Mount 6 Modules (UTPM6) Module Type G ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A PCN 020314-1 Universal Top-of-Pole Mount 6 Modules (UTPM6) for
More informationKIT ASSEMBLY INSTRUCTIONS
JUMPING JACK TRAILER KIT KIT ASSEMBLY INSTRUCTIONS A torque wrench (provided in the in-store tool kit) is required to assemble this trailer kit. Torque is a twisting (ft.-lb.).copy force measured in foot-pounds
More informationASSEMBLY INSTRUCTIONS
Universal Top-of-Pole Mount 5 Modules (UTPM5) Module Type G ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version, Rev A PCN 0904- Universal Top-of-Pole Mount 5 Modules (UTPM5) for Module
More informationINSTALLATION INSTRUCTIONS Small Flat Panel FMA Pivot Arrays Models: FMA-220 and FMA-320
INSTALLATION INSTRUCTIONS Small Flat Panel FMA Pivot Arrays The FMA-220 and FMA-320 pivot array allow both horizontal and vertical display pitch adjustment. The pitch adjustment range is 30 (15 up / 15
More informationRiverside. Windhaven Queen Storage Bed Assembly Instructions
Queen Storage Bed Page 1 of 7 2 pcs. 4 pcs. 4 pcs. 4 pcs. 2 pcs. 5/0 Queen Storage Bed 50773 -- 5/0 Storage Footboard w/platform Note: The 50773 Storage Footboard can be used with the 50770 Panel Headboard
More informationCNC Router Parts PRO Machine Kit Cable Track Installation Instructions
1 1 X CABLE TRACK TRAYS & BRACKETS The cable track on the side of the system is supported by a metal tray (or multiple trays for longer systems such as a PRO4896). These trays hang from brackets on the
More informationRiverside. Harbor Hill Queen Storage Bed Assembly Instructions
Queen Storage Bed Page 1 of 7 8 pcs. 8 pcs. 1 pc. 2 pcs. 3 pcs. 3 pcs. 4 pcs. 4 pcs. 4 pcs. 1 pc. 1 pc. 8 pcs. 8 pcs. 8 pcs. 2 pcs. 8 pcs. 1 pc. 25770 -- 4/6-5/0 Panel Headboard (NOTE: the 25775 Leather
More informationMPA-9000 Universal Ceiling Projector Mount Kit
I N S T R U C T I O N M A N U A L Universal Ceiling Projector Mount Kit The Universal Ceiling Projector Mount provides a unique, simplified method of ceiling mounting your inverted projector. This low
More informationCable Tray Kit: - Cable Tray - Cable Tray Cover - Power Block Support (x2) Top Support Kit: (x2) - 2 Top Supports. Quantities are per bench
Parts Included (per back to back bench) Column Kit: (x2) - 1 LH & 1 RH Column - Control Box - Hand Switch Cable Tray Kit: - Cable Tray - Cable Tray Cover - Power Block Support (x2) Depth Support Kit: -
More informationINSTALLATION INSTRUCTIONS SLBU / SLMU UNIVERSAL INTERFACE BRACKETS
INSTALLATION INSTRUCTIONS SLBU / SLMU UNIVERSAL INTERFACE BRACKETS The Universal Interface Bracket provides a solution for simplifying inventory of RPA and RPM series mounts and SLB/SLM projector brackets.
More informationHIGH RISE Portable Restroom Assembly Instructions
HIGH RISE Portable Restroom Assembly Instructions 2530 Xenium Lane North, Minneapolis, MN 55441 Telephone: 763-553-1900 / Fax: 763-553-1905 800-328-3332/ www.satelliteindustries.com PN 20930 REV C 8/16
More informationM2 Antenna Systems, Inc. Model No: 10-30LP8
M2 Antenna Systems, Inc. Model No: 10-30LP8 VSWR 2:1 TYPICAL VSWR @ 70 FT. 2:1 1.5:1 1.5:1 1.2:1 1.2:1 10 14 MHz 11 12 13 17 15 16 18 19 20 21 22 23 24 25 26 27 28 29 30 SPECIFICATIONS: Model...10-30LP8
More informationInstalling The Aliens Extermination Deluxe 50" Cabinet with Sintra Marquee
Installing The Aliens Extermination Deluxe 50" Cabinet with Sintra Marquee Document Part #: 040-0262-01 This document describes how to install The Aliens Extermination Deluxe Cabinet with Sintra Marquee
More informationRiverside. Harbor Hill King Storage Bed Assembly Instructions
King Storage Bed Page 1 of 7 8 pcs. 8 pcs. 1 pc. 2 pcs. 6 pcs. 3 pcs. 4 pcs. 4 pcs. 4 pcs. 1 pc. 1 pc. 2 pcs. 8 pcs. 8 pcs. 8 pcs. 8 pcs. 25780 -- 6/0-6/6 Panel Headboard (NOTE: the 25785 Leather Headboard
More informationSTRUCTURAL HOLDING, CT6 TOOL BOARD, AND CART ASSEMBLY
STRUCTURAL HOLDING, CT6 TOOL BOARD, AND CART ASSEMBLY IN20765 2015 Chief Automotive Technologies CO9545.5 Rev. - 11/02/15 CT6 Structural Holding Tool Board Cart Step 1: Caster Assembly. A.) Assemble 5
More informationInstallation Instructions
Installation Instructions For 4 foot / 1.2m Diameter Ultra-high Performance Antenna Model ADxxG-4-T2 Before Installation, please read the instructions carefully. This instruction guide covers the installation
More information1LG WALL MOUNTS - 1LG
WM WALL MOUNTS - 1LG 1LG The Universal One-Legged Mount (1LG) may be the one and only mount that can be installed on any part of any building. This mount is designed for many types of antennas home, TV,
More informationM2 Antenna Systems, Inc. Model No: 6M8GJ
M2 Antenna Systems, Inc. Model No: 6M8GJ SPECIFICATIONS: Model... 6M8GJ Frequency Range... 50.0 To 50.4 mhz *Gain, (FS) / Over gnd... 14.2 dbi / 19 dbi @ 20 Front to back... 20 db Typical Beamwidth...
More informationStrata. urniture. Adriana Instructions. Parts in the Arm Box: Parts in the Body Box: Watch our assembly videos at
1A Watch our assembly videos at www.strataf.com/videos Parts in the Arm Box: Arm - Outside View Arm - Inside View 1B Parts in the Body Box: Back Deck x 1 Seat Deck x 1 with the Feet attached Back Panel
More informationRiverside. Oakmont Queen Storage Bed Assembly Instructions
Queen Storage Bed Page 1 of 7 8 pcs. 8 pcs. 1 pc. 1 pc. 8 pcs. 8 pcs. 8 pcs. 8 pcs. 1 pc. 1 pc. 20270 --5/0 Sleigh Headboard 20274 --5/0-6/6 Bed Rails 20273 -- 5/0 Storage Footboard, Panels, Slats Queen
More informationSuper Tube Spiral Slide Instructions
Super Tube Spiral Slide Instructions Super Tube Spiral Slide 2 SECTIONS WITH OVERLAPPING FLANGES 3 SECTIONS WITHOUT OVERLAPPING FLANGES 3-1/2 LAG SCREW W/WASHER 5/16 X 1 BOLT W/WASHERS AND LOCK NUT 5/16
More informationM2 Antenna Systems, Inc. Model No: 2M HO LOOP
M2 Antenna Systems, Inc. Model No: 2M HO LOOP SPECIFICATIONS: Model... 2M HO LOOP Frequency Range... 144 To 144.5 MHz Gain, Typical @ 10 ft.... 4 dbd @ 10 deg. Gain, 2 STK @ 82 & 132... 8 dbd @ 9 deg.
More informationAdjustable Mount for 2.4-GHz WLAN Yagi Antenna (AIR-ACC2662)
Adjustable Mount for 2.4-GHz WLAN Yagi Antenna (AIR-ACC2662) This mount is designed to be used with the AIR-ANT1949 andair-ant2410y-r 2.4-GHz yagi antennas. The mount is designed to adjust the antenna
More informationAssembly Instructions: Bencher Skylark
Assembly Instructions: Bencher Skylark Tools Required: Pop Rivet Tool Tape Measure Hex Wrenches Screwdriver Several Disposable Rags Two Saw Horses Several boxes or bowls to hold fasteners and small parts
More informationINSTRUCTION MANUAL MANUAL DE INSTRUCCIONES
INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES Model Number/ No. de Modelo: WDB101 CLOTHES DRYER STACKING BRACKET CAUTION: BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS. Avanti
More information2014 MFJ ENTERPRISES, INC.
Model MFJ-1907 INSTRUCTION MANUAL CAUTION: Read All Instructions Before Operating Equipment MFJ ENTERPRISES, INC. 300 Industrial Park Road Starkville, MS 39759 USA Tel: 662-323-5869 Fax: 662-323-6551 VERSION
More informationJK-65 Five Element 6M Yagi
JK-65 Five Element 6M Yagi PO Box 266, Croton Falls, NY 10519-0266 845.228.8700 (TEL) 845.279.5526 (FAX) info@jkantennas.com Page 1 of 8 JK Antennas Limited Warranty and Liability JK Antennas ( Manufacturer
More informationInstallation Instructions
903-CIS0143-C Installation Instructions 0.9m Antenna LEAX Arkivator Telecom disclaims any liability for the results of improper or unsafe installation, inspection, maintenance, or removal practices. Torsgatan
More information