Frequency Responses and Active Filter Circuits
|
|
- Britton Hancock
- 5 years ago
- Views:
Transcription
1 Frequency Responses and Active Filter Circuits Compensation capacitors and parasitic capacitors will influence the frequency response Capacitors are also purposely added to create certain functions; e.g. integrators The most common use of energy storage elements in opamp circuits is for filtering Inductors are not as often used as capacitors because they are much bulkier and more difficult to integrate on an IC The order of the filter depends on the number of energy storage elements that are used Lecture 6-1
2 Ideal Filters V in ( jω) Hjω ( ) V out ( jω) = V V in ( jω) out ( jω) H(jω) H(jω) A Pass Stop A Stop Pass ω H ω ω L ω A H(jω) Stop Pass Stop A H(jω) Pass Stop Pass ω L ω H ω ω L ω H ω Lecture 6-2
3 Ideal Filters We know that a first order filter will not look like an ideal model: H(jω) A ω H ω Higher order filters will attempt to have sharper transitions at the cut-off frequencies, but sometimes at the expense of increased ripple A H(jω) ω H ω Lecture 6-3
4 First-Order Low Pass Filter Design for a 3dB cut-off frequency of 3π (radians/second), a dc gain of 2, and an input impedance of at least 1kΩ R2 C R1 v in v out Lecture 6-4
5 First-Order Low Pass Filter 2k 53pF Will the frequency dependence of the open loop gain present a problem for this circuit using a 741 opamp? v in 1k v out 2dB e-1 e e1 e2 e3 e4 e5 e6 e7 1 db db -1dB DB(VMOUT/VMIN) frequency Lecture 6-5
6 First-Order Low Pass Filter SPICE results for magnitude using 741 opamp model 1 frequency e e1 e2 e3 e4 e DB(VMOUT/VMIN) Lecture 6-6
7 First-Order Low Pass Filter SPICE results for phase using 741 opamp model 18 frequency e e1 e2 e3 e4 e PH(VMOUT/VMIN) Lecture 6-7
8 First-Order High Pass Filter Calculate a transfer function to approximate the cut-off frequency 4kΩ.159µF 1kΩ v out v in Lecture 6-8
9 First-Order High Pass Filter What is the high frequency gain for this circuit? 4kΩ.159µF 1kΩ v in v out Lecture 6-9
10 First-Order High Pass Filter SPICE results for magnitude using 741 opamp model 2 frequency e e1 e2 e3 e4 e DB(VMOUT/VMIN) Lecture 6-1
11 First-Order High Pass Filter Note that the low-pass nature of the opamp makes this high-pass filter a bandpass filter when using a 741-type opamp e frequency e e1 e2 e3 e4 e5 e6 e7 DB(VMOUT/VMIN) Lecture 6-11
12 First-Order High-Pass Filter SPICE results for phase using 741 opamp model Why the discontinuity? 2 frequency e e1 e2 e3 e4 e5. -2 PH(VMOUT/VMIN) Lecture 6-12
13 Band Pass Filter Design for a mid-band frequency gain of 5 (volts/volt), and f L =5Hz and f H =5kHz. C2 R2 C1 R1 v in v out Lecture 6-13
14 Band-Pass Filter C2 R2 C1 R1 v in v out Lecture 6-14
15 Band Pass Filter SPICE results for magnitude using 741 opamp model 2 frequency e e1 e2 e3 e4 e5 e DB(VMOUT/VMIN) Lecture 6-15
16 Band-Pass Filter SPICE results for phase using 741 opamp model 2 frequency e e1 e2 e3 e4 e5 e6. -2 PH(VMOUT/VMIN) Lecture 6-16
17 Noninverting Opamp Most of the circuits that we ve seen so far can also be designed in a noninverting configuration too R 2 R 1 V o V in Lecture 6-17
18 Other Noninverting Configurations But sometimes they are a bit trickier to solve What is the transfer function of this circuit? How is it best evaluated? R 4 R 3 V 1 V 2 R 1 R 2 V o Lecture 6-18
19 Second-Order Low Pass Filter Design for a 3dB cut-off frequency of 3π (radians/second), a dc gain of 2, and an input impedance of 1kΩ RB 1E3Ω Suggested configuration and element values from a book R1 1E3Ω RA 1E3Ω R2 1E3Ω VC8-15V VIN + SIN + C2 1214E-12F VC9 + 15V - C1 927E-12F + - Lecture 6-19
20 Second-Order Low Pass Filter SPICE results for magnitude using 741 opamp model Input impedance magnitude as a function of frequency 11 frequency e2 e3 e4 e5 e6 e7 K 1 9 VMIN/IMIN Lecture 6-2
21 Second-Order Low Pass Filter Input impedance phase as a function of frequency frequency e2 e3 e4 e5 e6 e PH(VMIN/IMIN) Lecture 6-21
22 Second-Order Low Pass Filter SPICE results for magnitude using 741 opamp model Fall-off is sharper for higher frequencies, but 3dB point is at 5.6kHz 1 frequency e e1 e2 e3 e4 e5 e DB(VMOUT) Lecture 6-22
23 Second-Order Low Pass Filter 3dB cut-off frequency is slightly off from 1.5kHz target What parameters do we change to lower it 3dB slightly? R1 1E3Ω VIN + SIN RA 1E3Ω + - R2 1E3Ω C2 1214E-12F RB 1E3Ω VC8-15V + - VC9 + 15V C1 927E-12F + - Lecture 6-23
24 Second-Order Low Pass Filter Design for a 3dB cut-off frequency of 3π (radians/second), a dc gain of 2, and an input impedance of 1kΩ using values determined by pole analysis RB 1E3Ω RA 1E3Ω VC8-15V + - R1 1E3Ω R2 1E3Ω VIN + SIN + C2 196E-12F VC9 + 15V - C1 9E-12F + - Lecture 6-24
25 Second-Order Low Pass Filter 3dB is now at 1.5kHz DB(VMOUT) frequency e e1 e2 e3 e4 e5 e6 Lecture 6-25
An active filters means using amplifiers to improve the filter. An acive second-order RC low-pass filter still has two RC components in series.
Active Filters An active filters means using amplifiers to improve the filter. An acive second-order low-pass filter still has two components in series. Hjω ( ) -------------------------- 2 = = ----------------------------------------------------------
More information( ) = V s ( jω ) = 2 kω, a = 4, R s. = 500 nf Draw a Bode diagram of the magnitude and phase of the frequency. Let R p. response H jω. V in.
Let R p = 2 kω, a = 4, = 6 kω, = 500 nf Draw a Bode diagram of the magnitude and phase of the frequency response H jω = V s ( jω ) ( jω ). V in The secondary impedance is Z s ( jω ) = R / jω s = +/ jω
More informationExperiment 8 Frequency Response
Experiment 8 Frequency Response W.T. Yeung, R.A. Cortina, and R.T. Howe UC Berkeley EE 105 Spring 2005 1.0 Objective This lab will introduce the student to frequency response of circuits. The student will
More informationdc Bias Point Calculations
dc Bias Point Calculations Find all of the node voltages assuming infinite current gains 9V 9V 10kΩ 9V 100kΩ 1kΩ β = 270kΩ 10kΩ β = 1kΩ 1 dc Bias Point Calculations Find all of the node voltages assuming
More informationCombination Notch and Bandpass Filter
Combination Notch and Bandpass Filter Clever filter design for graphic equalizer can perform both notch and bandpass functions Gain or attenuation is controlled by a potentiometer for specific frequency
More informationAssignment 11. 1) Using the LM741 op-amp IC a circuit is designed as shown, then find the output waveform for an input of 5kHz
Assignment 11 1) Using the LM741 op-amp IC a circuit is designed as shown, then find the output waveform for an input of 5kHz Vo = 1 x R1Cf 0 Vin t dt, voltage output for the op amp integrator 0.1 m 1
More informationElectric Circuit Theory
Electric Circuit Theory Nam Ki Min nkmin@korea.ac.kr 010-9419-2320 Chapter 15 Active Filter Circuits Nam Ki Min nkmin@korea.ac.kr 010-9419-2320 Contents and Objectives 3 Chapter Contents 15.1 First-Order
More informationHomework Assignment 01
Homework Assignment 01 In this homework set students review some basic circuit analysis techniques, as well as review how to analyze ideal op-amp circuits. Numerical answers must be supplied using engineering
More informationThe above figure represents a two stage circuit. Recall, the transfer function relates. Vout
LABORATORY 12: Bode plots/second Order Filters Material covered: Multistage circuits Bode plots Design problem Overview Notes: Two stage circuits: Vin1 H1(s) Vout1 Vin2 H2(s) Vout2 The above figure represents
More informationEE 230 Lecture 17. Nonideal Op Amp Characteristics
EE 3 Lecture 17 Nonideal Op Amp Characteristics Quiz 11 The dc gain of this circuit was measured to be 5 and the 3dB bandwidth was measured to be 6KHz. Determine as many of the following as possible from
More informationElectrical Circuits II (ECE233b)
Electrical ircuits II (EE33b) ariablefrequency Network Performance (Part 3) Anestis Dounavis The University of Western Ontario Faculty of Engineering Science Scaling Often the values of circuit parameters
More information1) Consider the circuit shown in figure below. Compute the output waveform for an input of 5kHz
) Consider the circuit shown in figure below. Compute the output waveform for an input of 5kHz Solution: a) Input is of constant amplitude of 2 V from 0 to 0. ms and 2 V from 0. ms to 0.2 ms. The output
More informationActive Filter Design Techniques
Active Filter Design Techniques 16.1 Introduction What is a filter? A filter is a device that passes electric signals at certain frequencies or frequency ranges while preventing the passage of others.
More informationTwo Stage Amplifier Design
Two Stage Amplifier Design ENGI 242 ELEC 222 HYBRID MODEL PI January 2004 ENGI 242/ELEC 222 2 Multistage Amplifier Design 1 HYBRID MODEL PI PARAMETERS Parasitic Resistances rb = rb b = ohmic resistance
More informationIntroduction to Signals, Passive RC Filters and Opamps
Introduction to Signals, ive RC Filters and Opamps LB Introduction In this laboratory exercise you design, build and test some simple filter circuits. his is mainly for you to get comfortable with circuit
More informationECE3204 D2015 Lab 1. See suggested breadboard configuration on following page!
ECE3204 D2015 Lab 1 The Operational Amplifier: Inverting and Non-inverting Gain Configurations Gain-Bandwidth Product Relationship Frequency Response Limitation Transfer Function Measurement DC Errors
More informationThe George Washington University School of Engineering and Applied Science Department of Electrical and Computer Engineering ECE 20 - LAB
The George Washington University School of Engineering and Applied Science Department of Electrical and Computer Engineering ECE 20 - LAB Experiment # 6 (Part I) Bipolar Junction Transistors Common Emitter
More informationTest Your Understanding
074 Part 2 Analog Electronics EXEISE POBLEM Ex 5.3: For the switched-capacitor circuit in Figure 5.3b), the parameters are: = 30 pf, 2 = 5pF, and F = 2 pf. The clock frequency is 00 khz. Determine the
More informationLinear IC s and applications
Questions and Solutions PART-A Unit-1 INTRODUCTION TO OP-AMPS 1. Explain data acquisition system Jan13 DATA ACQUISITION SYSYTEM BLOCK DIAGRAM: Input stage Intermediate stage Level shifting stage Output
More informationDesigning Information Devices and Systems II Fall 2018 Elad Alon and Miki Lustig Homework 4
EECS 16B Designing Information Devices and Systems II Fall 2018 Elad Alon and Miki Lustig Homework 4 This homework is solely for your own practice. However, everything on it is in scope for midterm 1,
More informationLoop Compensation of Voltage-Mode Buck Converters
Solved by Application Note ANP 6 TM Loop Compensation of Voltage-Mode Buck Converters One major challenge in optimization of dc/dc power conversion solutions today is feedback loop compensation. To the
More informationJames Lunsford HW2 2/7/2017 ECEN 607
James Lunsford HW2 2/7/2017 ECEN 607 Problem 1 Part A Figure 1: Negative Impedance Converter To find the input impedance of the above NIC, we use the following equations: V + Z N V O Z N = I in, V O kr
More informationAdvanced Measurements
Albaha University Faculty of Engineering Mechanical Engineering Department Lecture 9: Wheatstone Bridge and Filters Ossama Abouelatta o_abouelatta@yahoo.com Mechanical Engineering Department Faculty of
More informationA third-order active-r filter with feedforward input signal
Sādhanā Vol. 28, Part 6, December 2003, pp. 1019 1026. Printed in India A third-order active-r filter with feedforward input signal G N SHINDE 1,PBPATIL 2 and P R MIRKUTE 1 1 Department of Electronics,
More informationDownloaded from
VI SEMESTER FINAL EXAMINATION 2003 Attempt ALL questions. Q. [1] [a] What is filter? Why it is required? Define half power points, rolloff and centre frequency. [3] [b] Plot the magnitude and phase response
More informationElectronic Noise. Analog Dynamic Range
Electronic Noise Dynamic range in the analog domain Resistor noise Amplifier noise Maximum signal levels Tow-Thomas Biquad noise example Implications on power dissipation EECS 247 Lecture 4: Dynamic Range
More informationSIMULATION OF A SERIES RESONANT CIRCUIT ECE562: Power Electronics I COLORADO STATE UNIVERSITY. Modified in Fall 2011
SIMULATION OF A SERIES RESONANT CIRCUIT ECE562: Power Electronics I COLORADO STATE UNIVERSITY Modified in Fall 2011 ECE 562 Series Resonant Circuit (NL5 Simulation) Page 1 PURPOSE: The purpose of this
More informationAssist Lecturer: Marwa Maki. Active Filters
Active Filters In past lecture we noticed that the main disadvantage of Passive Filters is that the amplitude of the output signals is less than that of the input signals, i.e., the gain is never greater
More information+ power. V out. - power +12 V -12 V +12 V -12 V
Question 1 Questions An operational amplifier is a particular type of differential amplifier. Most op-amps receive two input voltage signals and output one voltage signal: power 1 2 - power Here is a single
More informationLab 2: Discrete BJT Op-Amps (Part I)
Lab 2: Discrete BJT Op-Amps (Part I) This is a three-week laboratory. You are required to write only one lab report for all parts of this experiment. 1.0. INTRODUCTION In this lab, we will introduce and
More informationLecture #3: Voltage Regulator
Lecture #3: Voltage Regulator UNVERSTY OF CALFORNA, SAN DEGO Voltage regulator is a constant voltage source with a high current capacity to drive a low impedance load. A full-wave rectifier followed by
More informationHomework Assignment 11
Homework Assignment 11 Question 1 (Short Takes) Two points each unless otherwise indicated. 1. What is the 3-dB bandwidth of the amplifier shown below if r π = 2.5K, r o = 100K, g m = 40 ms, and C L =
More informationEK307 Active Filters and Steady State Frequency Response
EK307 Active Filters and Steady State Frequency Response Laboratory Goal: To explore the properties of active signal-processing filters Learning Objectives: Active Filters, Op-Amp Filters, Bode plots Suggested
More informationESE 372 / Spring 2011 / Lecture 19 Common Base Biased by current source
ESE 372 / Spring 2011 / Lecture 19 Common Base Biased by current source Output from Collector Start with bias DC analysis make sure BJT is in FA, then calculate small signal parameters for AC analysis.
More informationHomework Assignment 12
Homework Assignment 12 Question 1 Shown the is Bode plot of the magnitude of the gain transfer function of a constant GBP amplifier. By how much will the amplifier delay a sine wave with the following
More informationLecture 17 Date: Parallel Resonance Active and Passive Filters
Lecture 17 Date: 09.10.2017 Parallel Resonance Active and Passive Filters Parallel Resonance At resonance: The voltage V as a function of frequency. At resonance, the parallel LC combination acts like
More informationAudio Applications for Op-Amps, Part III By Bruce Carter Advanced Analog Products, Op Amp Applications Texas Instruments Incorporated
Audio Applications for OpAmps, Part III By Bruce Carter Advanced Analog Products, Op Amp Applications Texas Instruments Incorporated This is the third in a series of articles on singlesupply audio circuits.
More informationRevised: January 26,
ECE 3274 Active Load Common Emitter Amplifier Project 1. Objective This project will show how the use of an active load in a common emitter amplifier can affect the gain open loop gain. 2. Components Qty
More informationHomework Assignment 05
Homework Assignment 05 Question (2 points each unless otherwise indicated)(20 points). Estimate the parallel parasitic capacitance of a mh inductor with an SRF of 220 khz. Answer: (2π)(220 0 3 ) = ( 0
More informationHomework Assignment 03
Homework Assignment 03 Question 1 (Short Takes), 2 points each unless otherwise noted. 1. Two 0.68 μf capacitors are connected in series across a 10 khz sine wave signal source. The total capacitive reactance
More informationHomework Assignment 03 Solution
Homework Assignment 03 Solution Question 1 Determine the h 11 and h 21 parameters for the circuit. Be sure to supply the units and proper sign for each parameter. (8 points) Solution Setting v 2 = 0 h
More informationThe steeper the phase shift as a function of frequency φ(ω) the more stable the frequency of oscillation
It should be noted that the frequency of oscillation ω o is determined by the phase characteristics of the feedback loop. the loop oscillates at the frequency for which the phase is zero The steeper the
More informationEE247 Lecture 2. Butterworth Chebyshev I Chebyshev II Elliptic Bessel Group delay comparison example. EECS 247 Lecture 2: Filters
EE247 Lecture 2 Material covered today: Nomenclature Filter specifications Quality factor Frequency characteristics Group delay Filter types Butterworth Chebyshev I Chebyshev II Elliptic Bessel Group delay
More informationLecture 8: More on Operational Amplifiers (Op Amps)
Lecture 8: More on Operational mplifiers (Op mps) Input Impedance of Op mps and Op mps Using Negative Feedback: Consider a general feedback circuit as shown. ssume that the amplifier has input impedance
More informationEE247 - Lecture 2 Filters. EECS 247 Lecture 2: Filters 2005 H.K. Page 1. Administrative. Office hours for H.K. changed to:
EE247 - Lecture 2 Filters Material covered today: Nomenclature Filter specifications Quality factor Frequency characteristics Group delay Filter types Butterworth Chebyshev I Chebyshev II Elliptic Bessel
More informationLast time: BJT CE and CB amplifiers biased by current source
Last time: BJT CE and CB amplifiers biased by current source Assume FA regime, then VB VC V E I B I E, β 1 I Q C α I, V 0. 7V Calculate V CE and confirm it is > 0.2-0.3V, then BJT can be replaced with
More informationECE 3274 Common-Emitter Amplifier Project
ECE 3274 Common-Emitter Amplifier Project 1. Objective The objective of this lab is to design and build the common-emitter amplifier with partial bypass of the emitter resistor to control the AC voltage
More informationINTRODUCTION TO FILTER CIRCUITS
INTRODUCTION TO FILTER CIRCUITS 1 2 Background: Filters may be classified as either digital or analog. Digital filters are implemented using a digital computer or special purpose digital hardware. Analog
More informationEE 233 Circuit Theory Lab 3: First-Order Filters
EE 233 Circuit Theory Lab 3: First-Order Filters Table of Contents 1 Introduction... 1 2 Precautions... 1 3 Prelab Exercises... 2 3.1 Inverting Amplifier... 3 3.2 Non-Inverting Amplifier... 4 3.3 Integrating
More informationIFB270 Advanced Electronic Circuits
IFB270 Advanced Electronic Circuits Chapter 12: The operational amplifier Prof. Manar Mohaisen Department of EEC Engineering Review of the Precedent Lecture Introduce the four layer diode Introduce the
More informationUniversity of Illinois at Chicago Spring ECE 412 Introduction to Filter Synthesis Homework #2 Solutions. Problem 1
Problem 1 (a) Magnitude (impedance) scale the circuit so that all resistors are 1kΩ. Solution: Since all of the resistors in the circuit are 1Ω, we need to magnitude scale by k m = 1000; therefore, we
More informationECE 3455: Electronics Section Spring Final Exam
: Electronics Section 12071 Spring 2011 Version B May 7, 2011 Do not open the exam until instructed to do so. Answer the questions in the spaces provided on the question sheets. If you run out of room
More informationFigure Derive the transient response of RLC series circuit with sinusoidal input. [15]
COURTESY IARE Code No: R09220205 R09 SET-1 B.Tech II Year - II Semester Examinations, December-2011 / January-2012 NETWORK THEORY (ELECTRICAL AND ELECTRONICS ENGINEERING) Time: 3 hours Max. Marks: 80 Answer
More informationSchool of Sciences. ELECTRONICS II ECE212A 2 nd Assignment
School of Sciences SPRING SEMESTER 2010 INSTRUCTOR: Dr Konstantinos Katzis COURSE / SECTION: ECE212N COURSE TITLE: Electronics II OFFICE RM#: 124 (1 st floor) OFFICE TEL#: 22713296 OFFICE HOURS: Monday
More informationENGR-4300 Spring 2008 Test 4. Name SOLUTION. Section 1(MR 8:00) 2(TF 2:00) 3(MR 6:00) (circle one) Question I (24 points) Question II (16 points)
ENGR-4300 Spring 2008 Test 4 Name SOLUTION Section 1(MR 8:00) 2(TF 2:00) 3(MR 6:00) (circle one) Question I (24 points) Question II (16 points) Question III (15 points) Question IV (20 points) Question
More informationChapter 2. Operational Amplifiers
Chapter 2. Operational Amplifiers Tong In Oh 1 2.5 Integrators and Differentiators Utilized resistors in the op-amp feedback and feed-in path Ideally independent of frequency Use of capacitors together
More informationCHAPTER 6: ALTERNATING CURRENT
CHAPTER 6: ALTERNATING CURRENT PSPM II 2005/2006 NO. 12(C) 12. (c) An ac generator with rms voltage 240 V is connected to a RC circuit. The rms current in the circuit is 1.5 A and leads the voltage by
More informationAmplifiers Frequency Response Examples
ECE 5/45 Analog IC Design We will use the following MOSFET parameters for hand-calculations and the µm CMOS models for corresponding simulations. Table : Long-channel MOSFET parameters. Parameter NMOS
More informationActive Filters - Revisited
Active Filters - Revisited Sources: Electronic Devices by Thomas L. Floyd. & Electronic Devices and Circuit Theory by Robert L. Boylestad, Louis Nashelsky Ideal and Practical Filters Ideal and Practical
More informationAP Physics C. Alternating Current. Chapter Problems. Sources of Alternating EMF
AP Physics C Alternating Current Chapter Problems Sources of Alternating EMF 1. A 10 cm diameter loop of wire is oriented perpendicular to a 2.5 T magnetic field. What is the magnetic flux through the
More informationTesting and Stabilizing Feedback Loops in Today s Power Supplies
Keywords Venable, frequency response analyzer, impedance, injection transformer, oscillator, feedback loop, Bode Plot, power supply design, open loop transfer function, voltage loop gain, error amplifier,
More informationEE301 ELECTRONIC CIRCUITS
EE30 ELECTONIC CICUITS CHAPTE 5 : FILTES LECTUE : Engr. Muhammad Muizz Electrical Engineering Department Politeknik Kota Kinabalu, Sabah. 5. INTODUCTION Is a device that removes or filters unwanted signal.
More informationEECS40 RLC Lab guide
EECS40 RLC Lab guide Introduction Second-Order Circuits Second order circuits have both inductor and capacitor components, which produce one or more resonant frequencies, ω0. In general, a differential
More informationLowpass Filters. Microwave Filter Design. Chp5. Lowpass Filters. Prof. Tzong-Lin Wu. Department of Electrical Engineering National Taiwan University
Microwave Filter Design Chp5. Lowpass Filters Prof. Tzong-Lin Wu Department of Electrical Engineering National Taiwan University Lowpass Filters Design steps Select an appropriate lowpass filter prototype
More informationFilters and Tuned Amplifiers
CHAPTER 6 Filters and Tuned Amplifiers Introduction 55 6. Filter Transmission, Types, and Specification 56 6. The Filter Transfer Function 60 6.7 Second-Order Active Filters Based on the Two-Integrator-Loop
More informationECE 310L : LAB 9. Fall 2012 (Hay)
ECE 310L : LAB 9 PRELAB ASSIGNMENT: Read the lab assignment in its entirety. 1. For the circuit shown in Figure 3, compute a value for R1 that will result in a 1N5230B zener diode current of approximately
More informationTelecommunication Electronics
Test 1 In the circuit shown in the diagram C1, C2 and C3 have negligible impedance at the operating frequency R1 = 120kΩ R2 = 220kΩ Rc = 6,8kΩ Val = 15 V hfe > 500 Vi C1 R1 R2 I1 Rc Ve Re1 Re2 C3 C2 V
More informationECE 3274 Common-Emitter Amplifier Project
ECE 3274 Common-Emitter Amplifier Project 1. Objective The objective of this lab is to design and build three variations of the common- emitter amplifier. 2. Components Qty Device 1 2N2222 BJT Transistor
More informationEUP3410/ A,16V,380KHz Step-Down Converter DESCRIPTION FEATURES APPLICATIONS. Typical Application Circuit
2A,16V,380KHz Step-Down Converter DESCRIPTION The is a current mode, step-down switching regulator capable of driving 2A continuous load with excellent line and load regulation. The can operate with an
More informationCHAPTER 14. Introduction to Frequency Selective Circuits
CHAPTER 14 Introduction to Frequency Selective Circuits Frequency-selective circuits Varying source frequency on circuit voltages and currents. The result of this analysis is the frequency response of
More informationVoltage Feedback Op Amp (VF-OpAmp)
Data Sheet Voltage Feedback Op Amp (VF-OpAmp) Features 55 db dc gain 30 ma current drive Less than 1 V head/floor room 300 V/µs slew rate Capacitive load stable 40 kω input impedance 300 MHz unity gain
More informationBJT Circuits (MCQs of Moderate Complexity)
BJT Circuits (MCQs of Moderate Complexity) 1. The current ib through base of a silicon npn transistor is 1+0.1 cos (1000πt) ma. At 300K, the rπ in the small signal model of the transistor is i b B C r
More informationExample #6 1. An amplifier with a nominal gain
1. An amplifier with a nominal gain A=1000 V/V exhibits a gain change of 10% as the operating temperature changes from 25 o C to 75 o C. If it is required to constrain the change to 0.1% by applying negative
More informationLaboratory on Filter Circuits Dr. Lynn Fuller
ROCHESTER INSTITUTE OF TECHNOLOGY MICROELECTRONIC ENGINEERING Laboratory on Filter Circuits Dr. Lynn Fuller Webpage: http://people.rit.edu/lffeee 82 Lomb Memorial Drive Rochester, NY 14623-5604 Tel (585)
More informationWhile the Riso circuit is both simple to implement and design it has a big disadvantage in precision circuits. The voltage drop from Riso is
Hello, and welcome to part six of the TI Precision Labs on op amp stability. This lecture will describe the Riso with dual feedback stability compensation method. From 5: The previous videos discussed
More informationA 3-STAGE 5W AUDIO AMPLIFIER
ECE 2201 PRELAB 7x BJT APPLICATIONS A 3-STAGE 5W AUDIO AMPLIFIER UTILIZING NEGATIVE FEEDBACK INTRODUCTION Figure P7-1 shows a simplified schematic of a 3-stage audio amplifier utilizing three BJT amplifier
More informationFilter Design in Continuous Conduction Mode (CCM) of Operation; Part 2 Boost Regulator
Application Note ANP 28 Filter Design in Continuous Conduction Mode (CCM) of Operation; Part 2 Boost Regulator Part two of this application note covers the filter design of voltage mode boost regulators
More informationENGR4300 Test 3A and 3B Fall 2003
Question 1 -- Astable Multivibrator R1 8 X1 18 1 1 2 U3 R2 TOPEN = 0 2 4 5 6 7 CC TRIGGER RESETOUTPUT CONTROL THRESHOLD DISCHARGE GND 555D R3 1Meg C1 C2 10uF.01uF 1 3 0 The circuit above has been simulated
More informationUNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering
UNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering EXPERIMENT 7 PHASE LOCKED LOOPS OBJECTIVES The purpose of this lab is to familiarize students with the operation
More informationLecture 8 ECEN 4517/5517
Lecture 8 ECEN 4517/5517 Experiment 4 Lecture 7: Step-up dcdc converter and PWM chip Lecture 8: Design of analog feedback loop Part I Controller IC: Demonstrate operating PWM controller IC (UC 3525) Part
More informationExperiment 4 Op-Amp Resonant Bandpass Filter
Experiment 4 Op-Amp Resonant Bandpass Filter Physics 116A, D. Pellett v. 1.01, Oct. 20, 2002 1 Introduction In this experiment you will become familiar with a bandpass filter made with an op-amp (active
More informationIntroduction to Analog Interfacing. ECE/CS 5780/6780: Embedded System Design. Various Op Amps. Ideal Op Amps
Introduction to Analog Interfacing ECE/CS 5780/6780: Embedded System Design Scott R. Little Lecture 19: Operational Amplifiers Most embedded systems include components that measure and/or control real-world
More informationECE4902 C Lab 7
ECE902 C2012 - Lab MOSFET Differential Amplifier Resistive Load Active Load PURPOSE: The primary purpose of this lab is to measure the performance of the differential amplifier. This is an important topology
More informationBoundary Mode Offline LED Driver Using MP4000. Application Note
The Future of Analog IC Technology AN046 Boundary Mode Offline LED Driver Using MP4000 Boundary Mode Offline LED Driver Using MP4000 Application Note Prepared by Zheng Luo March 25, 2011 AN046 Rev. 1.0
More informationDC to VHF DIFFERENTIAL VIDEO AMPLIFIER PACKAGE OUTLINE
FEATURES BANDWIDTH AND TYPICAL GAIN: 12 MHz at AVOL = 3 17 MHz at AVOL = 7 MHz at AVOL = VERY SMALL PHASE DELAY GAIN ADJUSTABLE FROM TO 3 DC to VHF DIFFERENTIAL VIDEO AMPLIFIER NO FREQUENCY COMPENSATION
More informationFREQUENCY RESPONSE AND PASSIVE FILTERS LABORATORY
FREQUENCY RESPONSE AND PASSIVE FILTERS LABORATORY In this experiment we will analytically determine and measure the frequency response of networks containing resistors, AC source/sources, and energy storage
More informationIntegrators, differentiators, and simple filters
BEE 233 Laboratory-4 Integrators, differentiators, and simple filters 1. Objectives Analyze and measure characteristics of circuits built with opamps. Design and test circuits with opamps. Plot gain vs.
More informationAdvanced Regulating Pulse Width Modulators
Advanced Regulating Pulse Width Modulators FEATURES Complete PWM Power Control Circuitry Uncommitted Outputs for Single-ended or Push-pull Applications Low Standby Current 8mA Typical Interchangeable with
More informationLinear DC-DC Conversion Topology and Component Selection
ECE 480 Application Note Team 7 November 14, 2014 Linear DC-DC Conversion Topology and Component Selection Jacob Brettrager Compact DC-AC Inverter ABSTRACT It is often necessary to convert direct current
More informationEE12: Laboratory Project (Part-2) AM Transmitter
EE12: Laboratory Project (Part-2) AM Transmitter ECE Department, Tufts University Spring 2008 1 Objective This laboratory exercise is the second part of the EE12 project of building an AM transmitter in
More informationOscillators. An oscillator may be described as a source of alternating voltage. It is different than amplifier.
Oscillators An oscillator may be described as a source of alternating voltage. It is different than amplifier. An amplifier delivers an output signal whose waveform corresponds to the input signal but
More informationCHAPTER 3 ACTIVE INDUCTANCE SIMULATION
CHAPTER 3 ACTIVE INDUCTANCE SIMULATION The content and results of the following papers have been reported in this chapter. 1. Rajeshwari Pandey, Neeta Pandey Sajal K. Paul A. Singh B. Sriram, and K. Trivedi
More informationLecture # 3 Circuit Configurations
CPEN 206 Linear Circuits Lecture # 3 Circuit Configurations Dr. Godfrey A. Mills Email: gmills@ug.edu.gh Phone: 0269073163 February 15, 2016 Course TA David S. Tamakloe CPEN 206 Lecture 3 2015_2016 1 Circuit
More informationZA3020LV 2A Step-Down,PWM,Switch-Mode DC-DC Regulator
General Description The is a monolithic step-down switch-mode regulator with internal Power MOSFETs. It achieves 2A continuous output current over a wide input supply range with excellent load and line
More informationUsing an automated Excel spreadsheet to compensate a flyback converter operated in current-mode. Christophe Basso, David Sabatié
Using an automated Excel spreadsheet to compensate a flyback converter operated in current-mode Christophe Basso, David Sabatié ON Semiconductor download Go to ON Semiconductor site and enter flyback in
More informationUniversity of Pittsburgh
University of Pittsburgh Experiment #1 Lab Report Frequency Response of Operational Amplifiers Submission Date: 05/29/2018 Instructors: Dr. Ahmed Dallal Shangqian Gao Submitted By: Nick Haver & Alex Williams
More informationEUP A,40V,200KHz Step-Down Converter
3A,40V,200KHz Step-Down Converter DESCRIPTION The is current mode, step-down switching regulator capable of driving 3A continuous load with excellent line and load regulation. The operates with an input
More informationEXPERIMENT 4: RC, RL and RD CIRCUITs
EXPERIMENT 4: RC, RL and RD CIRCUITs Equipment List Resistor, one each of o 330 o 1k o 1.5k o 10k o 100k o 1000k 0.F Ceramic Capacitor 4700H Inductor LED and 1N4004 Diode. Introduction We have studied
More informationECE 3274 Common-Collector (Emitter-Follower) Amplifier Project
ECE 3274 Common-Collector (Emitter-Follower) Amplifier Project 1. Objective This project will show the biasing, gain, frequency response, and impedance properties of a common collector amplifier. 2. Components
More informationLab 9 Frequency Domain
Lab 9 Frequency Domain 1 Components Required Resistors Capacitors Function Generator Multimeter Oscilloscope 2 Filter Design Filters are electric components that allow applying different operations to
More information