Homework Assignment 03
|
|
- Griffin McDonald
- 5 years ago
- Views:
Transcription
1 Homework Assignment 03 Question 1 (Short Takes), 2 points each unless otherwise noted. 1. Two 0.68 μf capacitors are connected in series across a 10 khz sine wave signal source. The total capacitive reactance is: (a) 46.8 Ω (b) 4.68 Ω (c) 7.45 Ω (d) 21 Ω Answer: The total capacitance is 0.34 μf. The reactance at 10 khz is X c = 1 (2πfC) = 1/(2π = 46.8 Ω. Thus, (a) is the answer. 2. In a VAC series RC circuit, if 20 VAC is measured across the resistor and 40 VAC is measured across the capacitor, the magnitude of the applied voltage is: (a) 60 VAC (b) 55 VAC (c) 50 VAC (d) 45 VAC Answer: The applied voltage is V IN = V R + jv C, so that V IN = V R 2 + V C 2 = 2, VAC. Thus (d) is the answer. 3. What is the magnitude of the current phase angle for a 5.6 μf capacitor and a 50-Ω resistor in series with a 1.1 khz, 5 VAC source? (a) 72.9 (b) 62.7 (c) 27.3 (d) 17.1 Answer: The impedance of the RC circuit is = R 1 j2πfc = 50 j25.84 Ω. The magnitude of the phase angle is tan 1 ( ) = Thus, (c) is the answer. 4. In the circuit, V 1 = 1.5 V, V 2 = 2.5 V, and all the resistors have value 20K. The output voltage is (a) 4.5 V (b) +4.5 V (c) 4 V (d) 0.5 V (e) +0.5 V Answer: This is a summing inverter with V out = V 1 (R 2 R 1 ) V 2 (R 2 R 1 ). Since all the resistors have same value, V out = V 1 V 2 = 4 V 1
2 5. An engineer measures the (step response) rise time of an amplifier as t r = 0.7 μs. Estimate the 3 db bandwidth of the amplifier. 6. What is the time constant of the circuit? Answer: BW 0.35 t r 0.35 = = 500 khz Answer: The resistance the capacitor sees is R TH = 10K 10K = 5K, so the time constant is τ = R TH C L = ( )( ) = 5 ms. 7. Consider the amplifier below. V in = 1.5 V, what is V out? Answer: Gain of 1 st amplifier is A f = (30) 10 = 3 and gain of the 2 nd amplifier is 1. Thus, overall gain is ( 3)( 1) = 3. The output voltage is thus V out = = 4.5 V. 8. A differential amplifier has a common-mode gain of 0.2 and a common-mode rejection ratio of What would the output voltage be if the single-ended input voltage was 7 mv rms? (a) 1.4 mv rms (b) 650 mv rms (c) 4.55 V rms (d) V rms Answer: CMMR = A d A c so that 3250 = A d 0.2 and A d = 650. The output voltage is = 4.55 mv rms. 9. An amplifier has a differential gain of -50,000 and a common-mode gain of 2. What is the common-mode rejection ratio? (a) db (b) 44 db (c) -44 db (d) db Answer: CMMR = 20 log 10 A d A c = 20 log = db, so the answer is (d). 2
3 10. If the feedback/input resistor ratio of a feedback amplifier is 4.6 with 1.7 V applied to the noninverting input, what is the output voltage value? (a) 7.82 V (b) Saturation (c) Cutoff (d) 9.52 V Answer: A v = 1 + R f R 1 = ( ) = 5.6. The output voltage is then V O = = 9.52 V. Thus, the answer is (d) 11. The output of the circuit shown is (a) Sine wave with frequency ω rad/s (b) Square wave with frequency ω 2π Hz (c) Triangular wave with frequency ω rad/s (d) Need additional information Answer: With no feedback, the circuit is highly non-linear and operates as a comparator, comparing the input amplitude against 0 V. The output is a square wave for frequency ω 2π Hz, so the answer is (b). 12. Decreasing the magnitude of the gain in the given circuit could be achieved by (a) Reducing amplitude of the input voltage (b) Increasing R f (c) Removing R f (d) Increasing R i 13. Answer: A = R f R i so one should increase R i to reduce the voltage gain. 14. Assuming ideal op-amp behavior, the input resistance R i of the amplifier is (a) R x (b) Ω (c) 0 Ω (d) R 1 (e) R 1 + R x 15. Answer: For an ideal op-amp, no current flows into the + input terminal, so the the input resistance is. This, the answer is (b). 3
4 16. In the circuit shown, the output voltage is (a) 5( ) = 25 V (b) 5(8 2) = 20 V (c) 15 V (d) 15 V (e) (8 2) = 120 V Answer: This is a non-inverting amplifier with gain ( ) = 5, so with a 5-V input the output should be 25 V. However, the op-amp is powered by a +15-V power supply, so that the output will be clamped to a value close to +15 V, so the answer is (c). 17. Consider the circuit shown. Assume ideal op-amp behavior. (a) V = V + = 5 V (op-amp operation) (b) V = 10 2 (2 + 8) = 2 V (voltage division) (c) V = 0 (op-amp input current = 0) (d) Need additional information Answer: These is no feedback in the circuit to create a virtual short (V = V + ). No current flows into the input terminals so that V follows from voltage division, so the answer is (b). 18. In the circuit below R 1 = 10K, R 2 = 15K, and R 3 compensates for the op-amp s input bias current. What should its value be to be effective? (a) 10K (b) 15K (c) 6K (d) 25K (e) Need I OS Answer: Choose R 3 = R 1 R 2 = 6K, so (c) is the answer. 4
5 19. What is the purpose of R 3 in the circuit below, and what should the value be to be effective? Answer: This compensates for the op-amp s input bias current. The value should be R 1 R What are the units of slew-rate? Answer: Typically, slew rate is expressed in V/μs. 21. What is the voltage gain A v = v o v s of the amplifier below if g m = 0.04 S and r o = 100K? (a) 400 (b) 400 (c) Need additional information (i.e., r π ) (d) 364 (e) 364 Answer: A v = g m (r o 10K) = 0.04(100K 10K) = so (e) is the correct answer. 22. An engineer measures the gain of the circuit below and finds that with an input voltage v i = 3 V, the output voltage is v o = 18 V, so that the gain of the amplifier is 6. However, op-amp theory suggests the gain is = 7.2. Give one phrase that could explain the difference. Answer: Slew Rate 5
6 23. Which of the circuit is a current-to-voltage converter? Answer: Circuit (a) 24. Which circuit is a voltage-to-current converter? Answer: Circuit (b) 6
7 25. In the circuit V IN = 10 V, R 1 = 10K, and R L = 5K. What current flows through R L? Answer: By op-amp action the voltage across R 1 is V in and the current through R 1 and R L is 10 10K = 1 ma. 26. The Thevenin voltage V TH for the circuit external to R L is (4 points) (a) V (b) V (c) V (d) V 27. Answer: V TH is the no-load voltage between terminals A and B. Using voltage division, V TH = (30 0 ) (j45 (90 + j45) ) = 6 + j12 V. This is equivalent to V, so the answer is (b). Answer: I = ( 8) (5K + 20K) = 0.37 ma V O = 8 + (20K)(I) = 0.14 V V O =?, I =? 7
8 28. Answer: This is a current-to-voltage converter with v O = i S R F = ( )( ) = 10 V i S = 10 µa, R F = 1 MΩ V, v o =? 29. Answer: This is a follower where v O = v +. Thus v O = v + = = 2 V v I = 6 V, v o =? 30. Answer: This is a noninverting amplifier where v + = v I1 2 + v I2 2 = = 3 v I1 = 2 V, v I2 = 4 V, v o =? Thus v O = v + = 2v + = 6 V 8
9 Question 2 Assume that the op-amp in the non-inverting buffer configuration below has infinite input resistance, zero output resistance, and an open-loop gain of A OL = 1,000. Determine the closed-loop gain A f = V o V s, and be sure to provide your answer to four decimal places. (6 points) Solution KVL around the loop shown below gives V s + V Rs + V i + V o = 0 Where V RS is the voltage across R s. However, no current flows into the op-amp, so V RS = 0, and the KVL equation becomes V s + V i + V o = 0 Now V o = 1,000V i = 1,000 V s, which means V i = V o 1,000, so the KVL equation becomes V s + V o 1,000 + V o = 0 Solving for A f = V o V s yields A f = 1,000 (1 + 1,000) =
10 Question 3 An amplifier has an input resistance R i = 1K, and has a voltage gain of A v = 100 when driven from a signal with internal resistance R s 0. The amplifier is used to amplify a v s = 1 mv signal from a sensor that has an internal resistance of R s 20K. What is the output amplitude? (6 points) Solution The sensor s internal resistance and the amplifier s input resistance form a voltage divider so that the effective input voltage is v i = 1 1 mv = 47.6 μv The output voltage is v o = A v v i = = 4.76 mv 10
11 Question 4 The multimeter in the figure below has a common-mode rejection specification of 80 db. What possible range of output voltages can the meter indicate? (6 points) Solution V + = 5.01 V, V = 5 V The difference voltage is V d = V + V = 0.01 V = 10 mv, and the common-mode voltage is V cm = (V + + V ) 2 = V A common-mode rejection specification of 80 db means that the multimeters will suppress V cm by a 80 db, which is equivalent to a factor The contribution of the common-mode error is thus = 0.5 mv. However, the sign is unknown. Thus, the multimeter could display anything in the range 9.5 mv V Display 10.5 mv 11
12 Question 5 The input voltage is v I for each ideal op-amp below. Determine each output voltage. Assume v I = 6 V. (2 points each) Solution (a) This is a follower where v O = v +. Thus v O = v + = = 2 V (b) Same answer as (a) (c) This is a noninverting amplifier where v O = ( )v + = 2v +. Thus 6 v O = 2v + = 2 6 = V
13 Question 6 The circuit below is driven by the series of pulses shown. Assume V C = 0 at t = 0. (a) Write an expression for v O. (2 points). (b) Determine the output voltage after n pulses. (4 points) (c) Use the results from (b) and design, by specifying values for R and C, so that the output voltage is -5 V after 5 pulses. (4 points) Solution Part (a) The output of the integrator is v O = 1 t v RC 0 I(t)dt. Part (b) v O decreases linearly with each pulse. A the end of the pulse the output voltage is 10 μs v O = RC The circuit holds this voltage until the next pulse, during which it again increases linearly. At the end of n pulses, the voltage is 10 μs v O = n RC Part (c) We have to design the circuit so that this voltage is -5 V when n = 5. Thus 10 μs 5 = 5 RC RC = 10 μs Pick C = 0.01 μf, then R = 1 kω. Other reasonable values will also work. 13
14 Question 7 Determine the voltage gain A v = v O v I for the ideal op-amp circuit shown. (10 points) (Hint: apply KCL at the junction of the T-network and the inverting input. Solution There is a virtual short between v + and v so that v + = v I. Call the voltage at the junction of the three resistors that form the T-network, v x. KCL at the T-network junction gives KCL at the inverting input gives v x v I 2R + v x R + v x v O = 0 2R v I R + v I v x 2R = 0 Solving for v x in the second equation gives v x = 3v I. Substituting this in the first KCL equation and some algebraic manipulation yields v O = 11v I A v = v O v I =
Homework Assignment True or false. For both the inverting and noninverting op-amp configurations, V OS results in
Question 1 (Short Takes), 2 points each. Homework Assignment 02 1. An op-amp has input bias current I B = 1 μa. Make an estimate for the input offset current I OS. Answer. I OS is normally an order of
More informationHomework Assignment 01
Homework Assignment 01 In this homework set students review some basic circuit analysis techniques, as well as review how to analyze ideal op-amp circuits. Numerical answers must be supplied using engineering
More information2. The. op-amp in and 10K. (a) 0 Ω. (c) 0.2% (d) (a) 0.02K. (b) 4. The. 5 V, then. 0V (virtual. (a) (c) Fall V. (d) V.
Homework Assignment 04 Question 1 (2 points each unless noted otherwise) 1. A 9-V dc power supply generates 10 W in a resistor. What peak-to-peak amplitude should an ac source have to generate the same
More informationHomework Assignment 04
Question 1 (Short Takes) Homework Assignment 04 1. Consider the single-supply op-amp amplifier shown. What is the purpose of R 3? (1 point) Answer: This compensates for the op-amp s input bias current.
More informationHomework Assignment 07
Homework Assignment 07 Question 1 (Short Takes). 2 points each unless otherwise noted. 1. A single-pole op-amp has an open-loop low-frequency gain of A = 10 5 and an open loop, 3-dB frequency of 4 Hz.
More informationHomework Assignment 01
Homework Assignment 01 In this homework set students review some basic circuit analysis techniques, as well as review how to analyze ideal op-amp circuits. Numerical answers must be supplied using engineering
More informationHomework Assignment 06
Question 1 (2 points each unless noted otherwise) Homework Assignment 06 1. True or false: when transforming a circuit s diagram to a diagram of its small-signal model, we replace dc constant current sources
More informationHomework Assignment 01
Homework Assignment 01 In this homework set students review some basic circuit analysis techniques, as well as review how to analyze ideal op-amp circuits. Numerical answers must be supplied using engineering
More information(b) 25% (b) increases
Homework Assignment 07 Question 1 (2 points each unless noted otherwise) 1. In the circuit 10 V, 10, and 5K. What current flows through? Answer: By op-amp action the voltage across is and the current through
More informationIntroduction to Analog Interfacing. ECE/CS 5780/6780: Embedded System Design. Various Op Amps. Ideal Op Amps
Introduction to Analog Interfacing ECE/CS 5780/6780: Embedded System Design Scott R. Little Lecture 19: Operational Amplifiers Most embedded systems include components that measure and/or control real-world
More informationHomework Assignment 07
Homework Assignment 07 Question 1 (Short Takes). 2 points each unless otherwise noted. 1. A single-pole op-amp has an open-loop low-frequency gain of A = 10 5 and an open loop, 3-dB frequency of 4 Hz.
More informationOPERATIONAL AMPLIFIER PREPARED BY, PROF. CHIRAG H. RAVAL ASSISTANT PROFESSOR NIRMA UNIVRSITY
OPERATIONAL AMPLIFIER PREPARED BY, PROF. CHIRAG H. RAVAL ASSISTANT PROFESSOR NIRMA UNIVRSITY INTRODUCTION Op-Amp means Operational Amplifier. Operational stands for mathematical operation like addition,
More informationES250: Electrical Science. HW6: The Operational Amplifier
ES250: Electrical Science HW6: The Operational Amplifier Introduction This chapter introduces the operational amplifier or op amp We will learn how to analyze and design circuits that contain op amps,
More informationUNIT I. Operational Amplifiers
UNIT I Operational Amplifiers Operational Amplifier: The operational amplifier is a direct-coupled high gain amplifier. It is a versatile multi-terminal device that can be used to amplify dc as well as
More informationPHYS 536 The Golden Rules of Op Amps. Characteristics of an Ideal Op Amp
PHYS 536 The Golden Rules of Op Amps Introduction The purpose of this experiment is to illustrate the golden rules of negative feedback for a variety of circuits. These concepts permit you to create and
More informationHomework Assignment 03 Solution
Homework Assignment 03 Solution Question 1 Determine the h 11 and h 21 parameters for the circuit. Be sure to supply the units and proper sign for each parameter. (8 points) Solution Setting v 2 = 0 h
More informationL02 Operational Amplifiers Applications 1
L02 Operational Amplifiers Applications 1 Chapter 9 Ideal Operational Amplifiers and Op-Amp Circuits Donald A. Neamen (2009). Microelectronics: Circuit Analysis and Design, 4th Edition, Mc-Graw-Hill Prepared
More informationHomework Assignment 06
Homework Assignment 06 Question 1 (Short Takes) One point each unless otherwise indicated. 1. Consider the current mirror below, and neglect base currents. What is? Answer: 2. In the current mirrors below,
More informationHomework Assignment 02
Question 1 (2 points each unless noted otherwise) 1. Is the following circuit an STC circuit? Homework Assignment 02 (a) Yes (b) No (c) Need additional information Answer: There is one reactive element
More informationIntroduction to Op Amps
Introduction to Op Amps ENGI 242 ELEC 222 Basic Op-Amp The op-amp is a differential amplifier with a very high open loop gain 25k AVOL 500k (much higher for FET inputs) high input impedance 500kΩ ZIN 10MΩ
More informationOp-Amp Simulation Part II
Op-Amp Simulation Part II EE/CS 5720/6720 This assignment continues the simulation and characterization of a simple operational amplifier. Turn in a copy of this assignment with answers in the appropriate
More information1. An engineer measures the (step response) rise time of an amplifier as. Estimate the 3-dB bandwidth of the amplifier. (2 points)
Exam 1 Name: Score /60 Question 1 Short Takes 1 point each unless noted otherwise. 1. An engineer measures the (step response) rise time of an amplifier as. Estimate the 3-dB bandwidth of the amplifier.
More informationLecture Notes Unit-III
Lecture Notes Unit-III FAQs Q1: An operational amplifier has a differential gain of 103 and CMRR of 100, input voltages are 120µV and 80µV, determine output voltage. 2 MARKS
More informationC H A P T E R 02. Operational Amplifiers
C H A P T E R 02 Operational Amplifiers The Op-amp Figure 2.1 Circuit symbol for the op amp. Figure 2.2 The op amp shown connected to dc power supplies. The Ideal Op-amp 1. Infinite input impedance 2.
More informationOperational Amplifiers. Boylestad Chapter 10
Operational Amplifiers Boylestad Chapter 10 DC-Offset Parameters Even when the input voltage is zero, an op-amp can have an output offset. The following can cause this offset: Input offset voltage Input
More informationELC224 Final Review (12/10/2009) Name:
ELC224 Final Review (12/10/2009) Name: Select the correct answer to the problems 1 through 20. 1. A common-emitter amplifier that uses direct coupling is an example of a dc amplifier. 2. The frequency
More informationLesson number one. Operational Amplifier Basics
What About Lesson number one Operational Amplifier Basics As well as resistors and capacitors, Operational Amplifiers, or Op-amps as they are more commonly called, are one of the basic building blocks
More informationOperational Amplifiers
Questions Easy Operational Amplifiers 1. Which of the following statements are true? a. An op-amp has two inputs and three outputs b. An op-amp has one input and two outputs c. An op-amp has two inputs
More information55:041 Electronic Circuits The University of Iowa Fall Exam 3. Question 1 Unless stated otherwise, each question below is 1 point.
Exam 3 Name: Score /65 Question 1 Unless stated otherwise, each question below is 1 point. 1. An engineer designs a class-ab amplifier to deliver 2 W (sinusoidal) signal power to an resistive load. Ignoring
More informationChapter 10: The Operational Amplifiers
Chapter 10: The Operational Amplifiers Electronic Devices Operational Amplifiers (op-amp) Op-amp is an electronic device that amplify the difference of voltage at its two inputs. It has two input terminals,
More informationDual operational amplifier
DESCRIPTION The 77 is a pair of high-performance monolithic operational amplifiers constructed on a single silicon chip. High common-mode voltage range and absence of latch-up make the 77 ideal for use
More informationAnalog Electronics. Lecture Pearson Education. Upper Saddle River, NJ, All rights reserved.
Analog Electronics V Lecture 5 V Operational Amplifers Op-amp is an electronic device that amplify the difference of voltage at its two inputs. V V 8 1 DIP 8 1 DIP 20 SMT 1 8 1 SMT Operational Amplifers
More informationLINEAR IC APPLICATIONS
1 B.Tech III Year I Semester (R09) Regular & Supplementary Examinations December/January 2013/14 1 (a) Why is R e in an emitter-coupled differential amplifier replaced by a constant current source? (b)
More informationChapter 10: Operational Amplifiers
Chapter 10: Operational Amplifiers Differential Amplifier Differential amplifier has two identical transistors with two inputs and two outputs. 2 Differential Amplifier Differential amplifier has two identical
More informationSection 6 Chapter 2: Operational Amplifiers
03 Section 6 Chapter : Operational Amplifiers eference : Microelectronic circuits Sedra sixth edition 4//03 4//03 Contents: - DC imperfections A. Offset voltage B. Solution of offset voltage C. Input bias
More informationHomework Assignment 10
Homework Assignment 10 Question The amplifier below has infinite input resistance, zero output resistance and an openloop gain. If, find the value of the feedback factor as well as so that the closed-loop
More informationOperational Amplifiers
Fundamentals of op-amp Operation modes Golden rules of op-amp Op-amp circuits Inverting & non-inverting amplifier Unity follower, integrator & differentiator Introduction An operational amplifier, or op-amp,
More informationIntroduction to Operational Amplifiers
P. R. Nelson ECE 322 Fall 2012 p. 1/50 Introduction to Operational Amplifiers Phyllis R. Nelson prnelson@csupomona.edu Professor, Department of Electrical and Computer Engineering California State Polytechnic
More informationHomework Assignment 11
Homework Assignment 11 Question 1 (Short Takes) Two points each unless otherwise indicated. 1. What is the 3-dB bandwidth of the amplifier shown below if r π = 2.5K, r o = 100K, g m = 40 ms, and C L =
More informationUNIT - 1 OPERATIONAL AMPLIFIER FUNDAMENTALS
UNIT - 1 OPERATIONAL AMPLIFIER FUNDAMENTALS 1.1 Basic operational amplifier circuit- hte basic circuit of an operational amplifier is as shown in above fig. has a differential amplifier input stage and
More informationSingle Supply, Rail to Rail Low Power FET-Input Op Amp AD820
a FEATURES True Single Supply Operation Output Swings Rail-to-Rail Input Voltage Range Extends Below Ground Single Supply Capability from + V to + V Dual Supply Capability from. V to 8 V Excellent Load
More informationHomework Assignment 13
Question 1 Short Takes 2 points each. Homework Assignment 13 1. Classify the type of feedback uses in the circuit below (i.e., shunt-shunt, series-shunt, ) Answer: Series-shunt. 2. True or false: an engineer
More informationLinear IC s and applications
Questions and Solutions PART-A Unit-1 INTRODUCTION TO OP-AMPS 1. Explain data acquisition system Jan13 DATA ACQUISITION SYSYTEM BLOCK DIAGRAM: Input stage Intermediate stage Level shifting stage Output
More informationCHAPTER-6. OP-AMP A. 2 B. 3 C. 4 D. 1
CHAPTER-6. OP-AMP [1]. A non inverting closed loop op amp circuit generally has a gain factor A. Less than one B. Greater than one C. Of zero D. Equal to one HINT: - For non inverting amplifier the gain
More informationHOME ASSIGNMENT. Figure.Q3
HOME ASSIGNMENT 1. For the differential amplifier circuit shown below in figure.q1, let I=1 ma, V CC =5V, v CM = -2V, R C =3kΩ and β=100. Assume that the BJTs have v BE =0.7 V at i C =1 ma. Find the voltage
More informationUNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering
UNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering EXPERIMENT 5 GAIN-BANDWIDTH PRODUCT AND SLEW RATE OBJECTIVES In this experiment the student will explore two
More informationHomework Assignment 12
Homework Assignment 12 Question 1 Shown the is Bode plot of the magnitude of the gain transfer function of a constant GBP amplifier. By how much will the amplifier delay a sine wave with the following
More informationApplied Electronics II
Applied Electronics II Chapter 3: Operational Amplifier Part 1- Op Amp Basics School of Electrical and Computer Engineering Addis Ababa Institute of Technology Addis Ababa University Daniel D./Getachew
More information350MHz, Ultra-Low-Noise Op Amps
9-442; Rev ; /95 EVALUATION KIT AVAILABLE 35MHz, Ultra-Low-Noise Op Amps General Description The / op amps combine high-speed performance with ultra-low-noise performance. The is compensated for closed-loop
More informationBasic Information of Operational Amplifiers
EC1254 Linear Integrated Circuits Unit I: Part - II Basic Information of Operational Amplifiers Mr. V. VAITHIANATHAN, M.Tech (PhD) Assistant Professor, ECE Department Objectives of this presentation To
More informationSingle Supply, Rail to Rail Low Power FET-Input Op Amp AD820
a FEATURES True Single Supply Operation Output Swings Rail-to-Rail Input Voltage Range Extends Below Ground Single Supply Capability from V to V Dual Supply Capability from. V to 8 V Excellent Load Drive
More informationFinal Exam. 1. An engineer measures the (step response) rise time of an amplifier as t r = 0.1 μs. Estimate the 3 db bandwidth of the amplifier.
Final Exam Name: Score /100 Question 1 Short Takes 1 point each unless noted otherwise. 1. An engineer measures the (step response) rise time of an amplifier as t r = 0.1 μs. Estimate the 3 db bandwidth
More informationOperational Amplifier BME 360 Lecture Notes Ying Sun
Operational Amplifier BME 360 Lecture Notes Ying Sun Characteristics of Op-Amp An operational amplifier (op-amp) is an analog integrated circuit that consists of several stages of transistor amplification
More informationMIC7122. General Description. Features. Applications. Ordering Information. Pin Configuration. Pin Description. Rail-to-Rail Dual Op Amp
MIC722 Rail-to-Rail Dual Op Amp General Description The MIC722 is a dual high-performance CMOS operational amplifier featuring rail-to-rail inputs and outputs. The input common-mode range extends beyond
More informationAssist Lecturer: Marwa Maki. Active Filters
Active Filters In past lecture we noticed that the main disadvantage of Passive Filters is that the amplitude of the output signals is less than that of the input signals, i.e., the gain is never greater
More informationGechstudentszone.wordpress.com
8.1 Operational Amplifier (Op-Amp) UNIT 8: Operational Amplifier An operational amplifier ("op-amp") is a DC-coupled high-gain electronic voltage amplifier with a differential input and, usually, a single-ended
More information1) Consider the circuit shown in figure below. Compute the output waveform for an input of 5kHz
) Consider the circuit shown in figure below. Compute the output waveform for an input of 5kHz Solution: a) Input is of constant amplitude of 2 V from 0 to 0. ms and 2 V from 0. ms to 0.2 ms. The output
More informationChapter 9: Operational Amplifiers
Chapter 9: Operational Amplifiers The Operational Amplifier (or op-amp) is the ideal, simple amplifier. It is an integrated circuit (IC). An IC contains many discrete components (resistors, capacitors,
More informationIFB270 Advanced Electronic Circuits
IFB270 Advanced Electronic Circuits Chapter 12: The operational amplifier Prof. Manar Mohaisen Department of EEC Engineering Review of the Precedent Lecture Introduce the four layer diode Introduce the
More informationv 0 = A (v + - v - ) (1)
UNIVERSITI TEKNOLOGI MALAYSIA KURSUS KEJURUTERAAN ELEKTRIK ELECTRONIC ENGINEERING LABORATORY 2 EXPERIMENT 2 : OPERATIONAL AMPLIFIER PRELIMINARY REPORT Name : Section : Group : Lecturer : Marks : 20 Attach
More informationEE 3305 Lab I Revised July 18, 2003
Operational Amplifiers Operational amplifiers are high-gain amplifiers with a similar general description typified by the most famous example, the LM741. The LM741 is used for many amplifier varieties
More informationEE LINEAR INTEGRATED CIRCUITS & APPLICATIONS
UNITII CHARACTERISTICS OF OPAMP 1. What is an opamp? List its functions. The opamp is a multi terminal device, which internally is quite complex. It is a direct coupled high gain amplifier consisting of
More informationBaşkent University Department of Electrical and Electronics Engineering EEM 311 Electronics II Experiment 8 OPERATIONAL AMPLIFIERS
Başkent University Department of Electrical and Electronics Engineering EEM 311 Electronics II Experiment 8 Objectives: OPERATIONAL AMPLIFIERS 1.To demonstrate an inverting operational amplifier circuit.
More informationLF411 Low Offset, Low Drift JFET Input Operational Amplifier
Low Offset, Low Drift JFET Input Operational Amplifier General Description These devices are low cost, high speed, JFET input operational amplifiers with very low input offset voltage and guaranteed input
More informationChapter 9: Operational Amplifiers
Chapter 9: Operational Amplifiers The Operational Amplifier (or op-amp) is the ideal, simple amplifier. It is an integrated circuit (IC). An IC contains many discrete components (resistors, capacitors,
More informationSpecial-Purpose Operational Amplifier Circuits
Special-Purpose Operational Amplifier Circuits Instrumentation Amplifier An instrumentation amplifier (IA) is a differential voltagegain device that amplifies the difference between the voltages existing
More informationDifferential Amplifier : input. resistance. Differential amplifiers are widely used in engineering instrumentation
Differential Amplifier : input resistance Differential amplifiers are widely used in engineering instrumentation Differential Amplifier : input resistance v 2 v 1 ir 1 ir 1 2iR 1 R in v 2 i v 1 2R 1 Differential
More informationECE:3410 Electronic Circuits
ECE:3410 Electronic Circuits Reiew of Op-Amps Sections of Chapters 9 & 14 A. Kruger Op-Amp Reiew-1 Real-World Op-Amp In earlier courses, op-amp were often considered ideal Infinite input resistance Infinite
More informationExample #6 1. An amplifier with a nominal gain
1. An amplifier with a nominal gain A=1000 V/V exhibits a gain change of 10% as the operating temperature changes from 25 o C to 75 o C. If it is required to constrain the change to 0.1% by applying negative
More informationHomework Assignment Consider the circuit shown. Assume ideal op-amp behavior. Which statement below is true?
Question 1 (2 points each unless noted otherwise) Homework Assignment 03 1. Consider the circuit shown. Assume ideal op-amp behavior. Which statement below is true? (a) V = VV + = 5 V (op-amp operation)
More informationLecture #2 Operational Amplifiers
Spring 2015 Benha University Faculty of Engineering at Shoubra ECE-322 Electronic Circuits (B) Lecture #2 Operational Amplifiers Instructor: Dr. Ahmad El-Banna Agenda Introduction Op-Amps Input Modes and
More informationChapter 2. Operational Amplifiers
Chapter 2. Operational Amplifiers Tong In Oh 1 2.5 Integrators and Differentiators Utilized resistors in the op-amp feedback and feed-in path Ideally independent of frequency Use of capacitors together
More informationHigh Common-Mode Rejection. Differential Line Receiver SSM2141 REV. B FUNCTIONAL BLOCK DIAGRAM FEATURES. High Common-Mode Rejection
a FEATURES High Common-Mode Rejection DC: 100 db typ 60 Hz: 100 db typ 20 khz: 70 db typ 40 khz: 62 db typ Low Distortion: 0.001% typ Fast Slew Rate: 9.5 V/ s typ Wide Bandwidth: 3 MHz typ Low Cost Complements
More informationAn electronic unit that behaves like a voltagecontrolled
1 An electronic unit that behaves like a voltagecontrolled voltage source. An active circuit element that amplifies, sums, subtracts, multiply, divide, differentiate or integrates a signal 2 A typical
More informationBJT Circuits (MCQs of Moderate Complexity)
BJT Circuits (MCQs of Moderate Complexity) 1. The current ib through base of a silicon npn transistor is 1+0.1 cos (1000πt) ma. At 300K, the rπ in the small signal model of the transistor is i b B C r
More informationChapter 3: Operational Amplifiers
Chapter 3: Operational Amplifiers 1 OPERATIONAL AMPLIFIERS Having learned the basic laws and theorems for circuit analysis, we are now ready to study an active circuit element of paramount importance:
More informationECE 3410 Homework 4 (C) (B) (A) (F) (E) (D) (H) (I) Solution. Utah State University 1 D1 D2. D1 v OUT. v IN D1 D2 D1 (G)
ECE 341 Homework 4 Problem 1. In each of the ideal-diode circuits shown below, is a 1 khz sinusoid with zero-to-peak amplitude 1 V. For each circuit, sketch the output waveform and state the values of
More informationMIC7300 A17. General Description. Features. Applications. Ordering Information. Pin Configurations. Functional Configuration.
MIC7300 High-Output Drive Rail-to-Rail Op Amp General Description The MIC7300 is a high-performance CMOS operational amplifier featuring rail-to-rail input and output with strong output drive capability.
More informationLF442 Dual Low Power JFET Input Operational Amplifier
LF442 Dual Low Power JFET Input Operational Amplifier General Description The LF442 dual low power operational amplifiers provide many of the same AC characteristics as the industry standard LM1458 while
More informationJames Lunsford HW2 2/7/2017 ECEN 607
James Lunsford HW2 2/7/2017 ECEN 607 Problem 1 Part A Figure 1: Negative Impedance Converter To find the input impedance of the above NIC, we use the following equations: V + Z N V O Z N = I in, V O kr
More informationAssignment 11. 1) Using the LM741 op-amp IC a circuit is designed as shown, then find the output waveform for an input of 5kHz
Assignment 11 1) Using the LM741 op-amp IC a circuit is designed as shown, then find the output waveform for an input of 5kHz Vo = 1 x R1Cf 0 Vin t dt, voltage output for the op amp integrator 0.1 m 1
More informationDual FET-Input, Low Distortion OPERATIONAL AMPLIFIER
www.burr-brown.com/databook/.html Dual FET-Input, Low Distortion OPERATIONAL AMPLIFIER FEATURES LOW DISTORTION:.3% at khz LOW NOISE: nv/ Hz HIGH SLEW RATE: 25V/µs WIDE GAIN-BANDWIDTH: MHz UNITY-GAIN STABLE
More informationLecture #4 Basic Op-Amp Circuits
Summer 2015 Ahmad El-Banna Faculty of Engineering Department of Electronics and Communications GEE336 Electronic Circuits II Lecture #4 Basic Op-Amp Circuits Instructor: Dr. Ahmad El-Banna Agenda Some
More informationChapter 14 Operational Amplifiers
1. List the characteristics of ideal op amps. 2. Identify negative feedback in op-amp circuits. 3. Analyze ideal op-amp circuits that have negative feedback using the summing-point constraint. ELECTRICAL
More informationAC reactive circuit calculations
AC reactive circuit calculations This worksheet and all related files are licensed under the Creative Commons Attribution License, version 1.0. To view a copy of this license, visit http://creativecommons.org/licenses/by/1.0/,
More informationSummer 2015 Examination
Summer 2015 Examination Subject Code: 17445 Model Answer Important Instructions to examiners: 1) The answers should be examined by key words and not as word-to-word as given in the model answer scheme.
More informationUnit 6 Operational Amplifiers Chapter 5 (Sedra and Smith)
Unit 6 Operational Amplifiers Chapter 5 (Sedra and Smith) Prepared by: S V UMA, Associate Professor, Department of ECE, RNSIT, Bangalore Reference: Microelectronic Circuits Adel Sedra and K C Smith 1 Objectives
More informationTest Your Understanding
074 Part 2 Analog Electronics EXEISE POBLEM Ex 5.3: For the switched-capacitor circuit in Figure 5.3b), the parameters are: = 30 pf, 2 = 5pF, and F = 2 pf. The clock frequency is 00 khz. Determine the
More informationQuestion. 1 (2 points. (a) (b) 10 khz (c) (d) 10.4 khz. (a) (b) khz (c) (d) 100 khz. 3. The. (a) (c) Fall What is the 3-dB. 1 nf?
Homework Assignment 02 Question 1 (2 points each unless noted otherwise) 1. What is the 3-dB bandwidth of the amplifier shown below if 2.5K, 100K, 40 ms, and 1 nf? (a) 65.25 khz (b) 10 khz (c) 1.59 khz
More informationusing dc inputs. You will verify circuit operation with a multimeter.
Op Amp Fundamentals using dc inputs. You will verify circuit operation with a multimeter. FACET by Lab-Volt 77 Op Amp Fundamentals O circuit common. a. inverts the input voltage polarity. b. does not invert
More informationPhysics 303 Fall Module 4: The Operational Amplifier
Module 4: The Operational Amplifier Operational Amplifiers: General Introduction In the laboratory, analog signals (that is to say continuously variable, not discrete signals) often require amplification.
More informationHomework Assignment 13
Question 1 Short Takes 2 points each. Homework Assignment 13 1. Classify the type of feedback uses in the circuit below (i.e., shunt-shunt, series-shunt, ) 2. True or false: an engineer uses series-shunt
More informationFHP3350, FHP3450 Triple and Quad Voltage Feedback Amplifiers
FHP335, FHP345 Triple and Quad Voltage Feedback Amplifiers Features.dB gain flatness to 3MHz.7%/.3 differential gain/phase error 2MHz full power -3dB bandwidth at G = 2,V/μs slew rate ±55mA output current
More informationLow Cost, Precision JFET Input Operational Amplifiers ADA4000-1/ADA4000-2/ADA4000-4
Low Cost, Precision JFET Input Operational Amplifiers ADA-/ADA-/ADA- FEATURES High slew rate: V/μs Fast settling time Low offset voltage:.7 mv maximum Bias current: pa maximum ± V to ±8 V operation Low
More informationZero Drift, Unidirectional Current Shunt Monitor AD8219
Zero Drift, Unidirectional Current Shunt Monitor FEATURES High common-mode voltage range 4 V to 8 V operating.3 V to +85 V survival Buffered output voltage Gain = 6 V/V Wide operating temperature range:
More informationIntegrators, differentiators, and simple filters
BEE 233 Laboratory-4 Integrators, differentiators, and simple filters 1. Objectives Analyze and measure characteristics of circuits built with opamps. Design and test circuits with opamps. Plot gain vs.
More informationElectronics basics for MEMS and Microsensors course
Electronics basics for course, a.a. 2017/2018, M.Sc. in Electronics Engineering Transfer function 2 X(s) T(s) Y(s) T S = Y s X(s) The transfer function of a linear time-invariant (LTI) system is the function
More informationImproved Second Source to the EL2020 ADEL2020
Improved Second Source to the EL ADEL FEATURES Ideal for Video Applications.% Differential Gain. Differential Phase. db Bandwidth to 5 MHz (G = +) High Speed 9 MHz Bandwidth ( db) 5 V/ s Slew Rate ns Settling
More informationOperational Amplifiers
Operational Amplifiers Spring 2008 Sean Lynch Lambros Samouris Tom Groshans History of Op Amps Non Named for their originally intended functions: performing mathematical operations and amplification Addition
More informationMIC915. Features. General Description. Applications. Ordering Information. Pin Configuration. Pin Description. Dual 135MHz Low-Power Op Amp
MIC915 Dual 135MHz Low-Power Op Amp General Description The MIC915 is a high-speed, unity-gain stable operational amplifier. It provides a gain-bandwidth product of 135MHz with a very low, 2.4mA supply
More information