Backyard Play. Bone Sign. Doghouse. YOU WILL NEED: Bead Colors: Instructions. Peg boards:

Transcription

1 You will also need a 12" x 12" shadow box, bright lime paint and brush, craft glue, 3/8" high letter stickers, and string or plastic cord to complete your project. NOTE: You will need 2 bags of Kiwi Lime beads, and 1 each of the colors. Peg boards: 2 Large squares Puppy Small circle Small hexagon YOU WILL NEED: Bead Colors: Red Rust Orange Yellow Cheddar Kiwi Lime Dark Green Turquoise Light Blue Dark Blue Light Brown Brown Grey Black White Instructions 1. Place your beads on the peg boards as shown. If you are using a clear peg board, slide the actual-size pattern underneath it. 2. Ask an adult to fuse your designs see Fusing Instructions on page Paint your shadow box inside and out. Instructions for the assembly of the bead pieces are on the pages that follow. Red - 60 Orange - 5 Cheddar - 42 Kiwi Lime Turquoise Light Blue - 60 Dark Blue - 80 White - 34 Bone Sign Doghouse 1

2 ASSEMBLY 1. Glue the Doghouse Base inside your shadow box about 3/4" from each side at lower left. 2. Press or glue the Dog Stands into the slots on the lower side of the Doghouse Base, and the Doghouse Stands into the slots on the upper side. 3. Sticker your pet's name or initials onto the Bone Sign and glue it to the Doghouse. Slide the Doghouse and Dog into their stands. Doghouse Stands Dog Stands Dog Red - 1 Kiwi Lime Turquoise - 25 Light Brown - 88 Black - 3 White Doghouse Base Fusing Instructions Only Adults Iron 1. Place your peg board on a flat, heat-safe surface. 2. Set a household iron to the medium setting. Place ironing paper over the peg board. In a circular motion, begin to iron the project. When ironed properly, the beads will still have an open center. Let the design cool. 3. Remove the paper and bead design from the peg board. Flip the design over to expose the non-fused side. Repeat step two. Let cool completely. Note: Beads need heat for about seconds per side to fuse evenly. Depending on the size of the project, additional heating time may be required. Since you are working on a 3-D project, DO NOT OVER-IRON the beads as it will make the centers of the beads close and can make assembly more challenging. 2

3 ASSEMBLY 1. Glue the Tree Base inside your shadow box about 1" from the top and 3/4" from right side. 2. Loop an 8" length of string or plastic cord through the Tire Swing and knot loosely. When your Tree is constructed, you will hang the Tire Swing from a tree branch and adjust the length as needed. Tire Swing Tree Base Rust - 22 Yellow - 21 Kiwi Lime Dark Green - 63 Grey - 12 Black

4 Tree Part A USING TWO CONNECTED SQUARES 1. Position your two large square peg boards as shown at left and snap them together. 2. Print the patterns on this page and the next. Cut them out and tape together so the s are perfectly aligned. 3. Place all the beads, then iron the Tree Part A as one piece. 4. Follow this same general procedure for the other parts of the project that require two large square peg boards. Tree Part A-upper Kiwi Lime Dark Green

5 Tree Part A-lower Tree Part A Rust - 99 Kiwi Lime Dark Green Brown

6 Tree Part B Tree Part B-upper Kiwi Lime Dark Green

7 Tree Part B-lower Tree Part B Rust - 94 Kiwi Lime Dark Green Brown - 53 ASSEMBLY 1. Hold your Tree Part A and Tree Part B sections at right angles to each other, then slide the slot in the branches of Part A up through the slot in the trunk of Part B. Align the pieces at the bottom of the trunk. 2. Press or glue your tree into the slots of the Tree Base. 3. Hang the Tire Swing from one of the branches. 7

8 Street, Flower, & Birds - left Cheddar - 44 Grey White

9 ASSEMBLY Street, Flowers, & Birds - right 1. Glue the Street diagonally into the upper left of your shadow box, aligning the edges. 2. Press or glue the flowers and one bird into the small slots in the Tree Base. Slide two of the birds into the vertical slots in the tree. 3. For a finishing touch, add a mix of loose beads in Kiwi Lime and Dark Green around the Tree and Doghouse Bases. Orange - 26 Yellow - 29 Cheddar - 41 Kiwi Lime - 5 Dark Green - 30 Light Blue - 24 Light Brown - 32 Grey Black - 10 White Perler Beads and EKSuccess Brands are either registered trademarks or trademarks of Dimensions Crafts LLC and EK Success Ltd. respectively in the United States and/or other countries Dimensions Crafts LLC. All rights reserved. 9