The Park Hotel Instructions for Assembly

Size: px
Start display at page:

Download "The Park Hotel Instructions for Assembly"

Transcription

1 The Park Hotel Instructions for Assembly Kit Contents: 280 ea. Laser Cut Acrylic Parts. 1 ea. 6" Plastic Coated Wire. 5 ea. Sidewalk Parts. 14 ea. Cast Resin Dormers. 12 ea. Window Glass Templates, 12 ea. Window Glazing, instructions with diagrams. Thank you for purchasing this kit. Please read these instructions completely before beginning and take your time. Allow parts to dry after painting or gluing and do not try to build this in one night. Drawings of all the parts have been included for ease of part identification. Practice gluing the acrylic together if you have never done it before. There is plenty of scrap in your kit that you can use for this. If by chance a part is missing or broken, please write us indicating the kit name and part number and we will send you a replacement. You will need the following items to assemble your model: Sharp hobby knife, file, paint (see Painting Your Model ), paint brushes, glue (see Gluing Acrylic ), modeling putty. About the Kit This kit will build a 24 story building. The kit is built up in modules labeled as units. There are six units in all. The units range from three to eight stories. The units stack on top of each other when completed. The assembly of each unit is very similar. Once you have built the first unit you will most likely be able to build the rest without reading the instructions. However... I spent a lot of time writing the instructions so I would appreciate it if you would. Repetitive sequences will be described in detail the first time and then less so subsequently. Parts are labeled in the instructions inside parentheses. The first number is the unit number and the second is the part number in that unit. For instance (3-6) would be unit three part six. Each unit has a base and top that are identified with a letter. Many parts have engraved details on them. Be sure that these are facing out when gluing the parts together. It is easy to install these backwards by mistake. 1

2 Gluing Acrylic Always glue acrylic in a well-ventilated area, and read the glue manufacturer s label for instructions. We recommend using Tenax-7R by Hebco or Plastruct brand Plastic Weld Solvent Cement (PPC-2 or PPC-16) or Bondine Solvent Cement (Bond-2 or BOND-16). Tenax-7R comes with a dispenser and Plastruct sells a Solvent Syringe (HT-8 or HT-10) and various other solvent dispensers. Most hobby shops carry these products or they may be ordered directly from Hebco (931) or Plastruct (626) Acrylic must be glued together using a solvent that will melt the two edges and literally fuse them together. To do this, place the two pieces to be joined together and run a bead of solvent down the edge. Capillary action will suck the solvent into the joint and after several seconds the pieces will be fused. After only a few minutes the pieces will be strong enough to work with. The bond will be completely dry within twenty-four hours using the above-mentioned products. Solvent can be dispensed two ways. Typically the solvent comes in a small bottle with a brush in the lid. The brush allows you to dispense a drop or two of solvent at a time. You may want to use a polyethylene bottle or syringe with a blunt needle dispenser. This allows larger amounts of solvent to be dispensed quickly and cleanly. Be sure the bottle you are using is approved for the solvent you are using or you may melt through it. These may be purchased from CMR. Preparing Your Model for Painting We recommend lightly sanding all parts to remove the raised edge created during the laser cutting process. In order to hide the seams we recommend using hobbyist putty such as Green Squadron modeling putty. Do this in a very wellventilated area. Apply the putty over the seams and allow to dry overnight. Once the putty has dried, place a sheet of fine sandpaper on a flat surface and sand smooth. You may need to apply a second coat of putty and sand again. You may choose to wrap the engraved lines around the corners with a small triangular jewelers file. 2

3 Painting Your Model After building each unit and prior to installing the windows, we primed our building with Krylon Gray spray paint. We also primed the window frames. For our building paint scheme, we used Poly Scale Acrylic paints which are available in most hobby stores. We also used Poly Scale Acrylics for details and weathering. Always test compatibility of your paint with the acrylic by painting and testing a small area first. We painted the first unit of the building very light grey and the windows light grey and bronze. We painted the upper stories dark grey and the windows light grey. We then made a white wash with Poly Scale paints. The building units were laid flat with a wall facing up and the wash was applied and allowed to dry. The unit was then rotated to the next wall and the process was repeated, and so on. We air brushed the back and alley walls with a dirty black mix so that they would be darker. Finally, we installed the painted windows into the units. We painted the roof a corroded green tin color and gave it a heavy white wash. The dormers and chimneys were painted the same as the building. Note on Tabs Sometimes it is necessary to sand or file the tabs slightly in order to get them to seat themselves into the slots. This is due to slight variations in acrylic thickness. If the tabs are not fitting into the slots properly, you may need to file them back at an angle to fit properly. Window Glass There are printed window shades included with your kit. These are designed to be laminated with acetate window glazing prior to installing in your model. The printed window shades are numbered to correspond with the window frame parts. Lightly spray glue the window shade page on the printed side with spray mount and apply a sheet of acetate. Press in place. We used 3M Spray Mount part number 6065 which is available at craft and office supply stores. Glue these to the back of the painted window frames using super glue (CA). After gluing the window glazing to the window frames, place the assembly face up on a cutting matt and trim off any excess glazing with a hobby knife. See figure 1. Figure 1 3

4 Assembling the Tower Units The first unit of this structure is asymmetrical in that opposite sides do not match one another in detail and character. Figure 2 shows base part (A) face up with the first set of wall parts face down and ready to install into their appropriate places. Be sure when installing parts that the engraved side is facing out. Orientation is from the front. The right side wall is to the right of the front wall. Figure 2 Please note that all pieces referred to as bases and tops (parts A, B, C, etc...) should have the part number facing up during assembly unless otherwise noted. This is the correct orientation to insure that the tabs on the wall parts will fit into the slots facing the right direction. Unit 1 Begin by taking base (A) and laying it flat on your work surface with the engraved part number facing up. Working clockwise, insert the tabs of the front wall (1-1) into the slots on the front side of part (A) and glue in place (see figure 2 for orientation). Note that the tabs on the top and bottom of the wall parts are different sizes, and the walls will only fit into part (A) in one direction. Make sure that the engraved side is facing out. Next, insert the tabs of the left side wall (1-2) into the slots on the left side of part (A) and glue in place. The two walls should meet and be glued at the corner. Insert the tabs of the back wall (1-3) into the slots on the back side of part (A) and glue in place. Then, insert the tabs of the right side wall (1-4) into the slots on the right side of part (A) and glue in place to form a box. Make sure to glue all the corners together. See Figure 3. Figure 3 4

5 Glue the top (B) onto the assembly with the engraved part number facing up. Check that all the tabs are seated properly. See Figure 4. Now that the basic wall structure is together the walls get built out to create a decorative facade. Begin by gluing the left side (1-6) and the right side (1-8) to their appropriate walls making sure they are flush with the adjoining wall. If necessary file the edges so that the corners are perfectly flush. Next glue the front (1-5) and back (1-7) to their respective walls. They will overlap the sides and should be perfectly flush on the edges. If necessary file the edges so that the corners are perfectly flush. See Figures 5 & 6. Figure 4 Figure 5 Figure 6 Glue part (1-9) onto part (1-5). Glue part (C) on top of part (B). The center openings should align perfectly. See Figure 7 Figure 7 5

6 Fill and sand the corners of the assembly if necessary. You may choose to wrap the engraved lines around the corners with a small triangular jewelers file. See Preparing your Model for Painting. Paint the unit and set aside to dry. See Figure 8 Paint the window frames (1-10), (1-11), (1-12), (1-13), and (1-14) your choice of color. We painted ours light grey. Then we masked off the upper windows and painted the large windows and doors shiny gold. Install the window glazing as described earlier. Install part (1-10) behind the front wall, part (1-11) behind the left side wall, part (1-12) behind the right side wall, and parts (1-13) and (1-14) behind the back wall. See Figure 9. Figure 8 Assemble the awning by gluing parts (A-2), (A-3) and (A-4) to (A-1). Paint and attach to the front of Unit 1 above the main door. Cut two lengths of wire to 1.25" long and glue in place to support the awning. See Figure 10. Paint the Garage Door (1-15) dark gray and glue in place behind the door opening in part (1-2). See Figure 10. Figure 9 Figure 10 6

7 Unit 2 Place base (D) flat on your work surface with the engraved number facing up. Glue part (2-1) into the center slots located in the front of part (D). Glue parts (2-2) and (2-3) on either side of part (2-1) using the tabs and slots for alignment. See Figure 11. Glue part (2-4) into the center slots located in the left side of part (D). Glue part (2-2) and (2-3) on either side of part (2-4) using the tabs and slots for alignment. Repeat on the right side. See Figure 12 Figure 11 Figure 13 Figure 12 Glue the six parts (2-5) into the slots of part (D) using Figure 13 for placement. Part (2-6) is shipped in two parts and will need to be glued together using a part (2-8) to bridge the seam as shown in figure 14. Note that part (2-8) is a wider part than the similar part (2-7) that will be used later. 7 Figure 14

8 Glue the assembled part (2-6) to the back of part (D). Make sure the corners are flush with the parts (2-5) on either side of it. See Figure 15. Glue part (E) on top of the assembly using the tabs and slots for alignment. See Figure 15. Next glue the decorative corners in place. Each corner is made up of one part (2-7) and one part (2-8). You will notice that part (2-7) is narrower and has the edges notched only on one side. Part (2-8) is wider and has the edges notched on both sides. Glue part (2-7) on first so that the non-notched side is flush with the corner. Next glue part (2-8) onto the corner so that it overlaps part (2-7). Use part (2-8) on the side of the corner that will be the most visible to prevent you from seeing the seam. See Figure 16. Figure 15 Figure 16 Fill and sand the corners of the assembly if necessary. You may choose to wrap the engraved lines around the corners with a small triangular jewelers file. See Preparing your Model for Painting. Paint the unit and set aside to dry. 8

9 Paint the window frames (2-9), (2-10), (2-11), (2-12), and (2-13) your choice of color and install the window glazing as described earlier. Install window frame (2-9) behind wall part (2-1). Install the nine window frames (2-10) behind walls (2-2), (2-3), (2-4) and the left side of (2-6A). Install the six window frames (2-11) behind the walls (2-5). Install window frame (2-12) behind wall (2-6B). Install window frame (2-13) behind the right side of wall (2-6A). See Figure 17. Figure 17 9

10 Unit 3 Place base (F) flat on your work surface with the engraved number facing up. Glue part (3-1) into the center slots located in the front of part (F). Glue parts (3-2) and (3-3) on either side of part (3-1) using the tabs and slots for alignment. See Figure 18. Glue part (3-4) into the center slots located in the left side of part (F). Glue part (3-2) and (3-3) on either side of part (3-4) using the tabs and slots for alignment. Repeat on the right side. See Figure 19. Figure 18 Glue the six parts (3-5) into the slots of part (F) using Figure 20 for placement. Figure 19 Figure 20 Glue part (3-6) to the back of part (F). Make sure the corners are flush with the parts (3-5) on either side of it. Glue part (E) on top of the assembly using the tabs and slots for alignment. See Figure 21. Figure 21 10

11 Next glue the decorative corners in place. Each corner is made up of one part (3-7) and one part (3-8). You will notice that part (3-7) is narrower and has the edges notched only on one side. Part (3-8) is wider and has the edges notched on both sides. Glue part (3-7) on first so that the nonnotched side is flush with the corner. Next glue part (3-8) onto the corner so that it overlaps part (3-7). Use part (3-8) on the side of the corner that will be the most visible to prevent you from seeing the seam. See Figure 22. Glue two parts (3-8) to the back wall part (3-6) using the engraved lines on the wall for location. See Figure 22. Figure 22 Fill and sand the corners of the assembly if necessary. You may choose to wrap the engraved lines around the corners with a small triangular jewelers file. See Preparing your Model for Painting. Paint the unit and set aside to dry. Paint the window frames (3-9), (3-10), (3-11), and (3-12) your choice of color and install the window glazing as described earlier. Install window frame (3-9) behind wall part (3-1). Install the eight window frames (3-10) behind walls (3-2), (3-3), and (3-4). Install the six window frames (3-11) behind the walls (3-5). Install window frame (3-12) behind wall (3-6). See Figure 23. Figure 23 11

12 Unit 4 Unit 4 has terraces that extend out from the bottom of it and sit on top of the unit below. In some situations these terraces may curl or cusp after construction as a result of glue or paint solvent causing the surface tension of the acrylic to be released on the top side only. To prevent this from happening we recommend that Unit 4 be built and attached to unit 3 with in a 48 hour period. Unit four is different from the earlier units. The wall assembly is symmetrical and the building begins stepping in at this point. We will also be adding railings to the balconies. Figure 24 Place base (G) flat on your work surface with the engraved number facing up. Glue part (4-1) into the center slots located in the front of part (G). Glue parts (4-2) and (4-3) on either side of part (4-1) using the tabs and slots for alignment. Repeat the process on the back of part (G). See Figure 24. Glue part (4-4) into the center slots located in the left side of part (G). Glue part (4-2) and (4-3) on either side of part (4-4) using the tabs and slots for alignment. Repeat on the right side. See Figure 25. Glue the eight parts (4-5) into the slots of part (F) to create the corners, using Figure 26 for placement. Figure 25 Glue part (H) on top of the assembly using the tabs and slots for alignment. See Figure 26. Figure 26 12

13 Next glue the decorative corners in place. Each corner is made up of one part (4-6) and one part (4-7). You will notice that part (4-6) is narrower and has the edges notched only on one side. Part (4-7) is wider and has the edges notched on both sides. Glue part (4-6) on first so that the nonnotched side is flush with the corner. Next glue part (4-7) onto the corner so that it overlaps part (4-6). Use part (4-7) on the side of the corner that will be the most visible to prevent you from seeing the seam. See Figure 27. Install the railings (R4-1), (R4-2), (R4-3) and (R4-4) as shown in Figure 28. Figure 27 Fill and sand the corners of the assembly if necessary. You may choose to wrap the engraved lines around the corners with a small triangular jewelers file. See Preparing your Model for Painting. Paint the unit and set aside to dry. Paint the window frames (4-8), (4-9), and (4-10) your choice of color and install the window glazing as described earlier. Figure 28 Install the window frames (4-8) behind walls (4-1). Install the window frames (4-9) behind walls (4-4). Install the window frames (4-10) behind the walls (4-5). See Figure 29. Figure 29 13

14 Unit 5 Unit 5 has terraces that extend out from the bottom of it and sit on top of the unit below. In some situations these terraces may curl or cusp after construction as a result of glue or paint solvent causing the surface tension of the acrylic to be released on the top side only. To prevent this from happening we recommend that Unit 5 be built and attached to unit 4 with in a 48 hour period. Glue part (5-3) onto the back of part (5-1) using the engraved lines on part (5-3) for alignment. Do this twice. See Figure 30. Figure 30 Place base (I) flat on your work surface with the engraved number facing up. Glue one part (5-1) into the slots located along the long side of part (I). Glue two parts (5-2) on either side of part (5-1) using the tabs and slots for alignment. Glue the remaining part (5-1) on the other side of the assembly to form a box. Glue part J on top of your assembly. See Figures 31 & 32. Next glue the decorative corners in place. Each corner is made up of one part (5-4) and one part (5-5). You will notice that part (5-4) is narrower and has the edges notched only on one side. Part (5-5) is wider and has the edges notched on both sides. Glue part (5-4) on first so that the nonnotched side is flush with the corner. Next glue part (5-5) onto the corner so that it overlaps part (5-4). See Figure 32. Figure 31 Glue two parts (5-5) onto each of the walls (5-1) and (5-2) as shown in Figure 32. VERY IMPORTANT!... parts (5-5) should align with the decorative corners on Unit 4 and you should make sure they align vertically when you glue them in place. See Figure 33 on the next page. Install the railings (R5-1), (R5-2) and (R5-3) as shown in Figure 32. Figure 32 14

15 Fill and sand the corners of the assembly if necessary. You may choose to wrap the engraved lines around the corners with a small triangular jewelers file. See Preparing your Model for Painting. Paint the unit and set aside to dry. Paint the window frames (5-6), (5-7), and (5-8) your choice of color and install the window glazing as described earlier. Install the window frames (5-6) behind walls (5-1). Install the window frames (5-7) behind walls (5-3). Install the window frames (5-8) behind walls (5-2). See Figure 34. Figure 33 Figure 34 15

16 Unit 6 Begin by gluing the dentils part (K) to the bottom of part (L) centering it on all sides. The bottom would be the side without the part number and engraving on it. See Figure 35. Flip assembly over and glue trim part (M) to the top of part (L) using the outside engraved line for alignment. Glue the roof support (6-1) into the slots on the top of part (L) followed by the two parts (6-2) which slide down onto part (6-1) and into (L). See Figure 36. Figure 35 Glue the two short roof pieces (6-4) onto the ends of the roof support (6-1) using the engraved lines on part (L) to keep them square. Make sure the engraved lines are facing out on the roof parts. See Figure 37. Glue the two long roof pieces (6-3) to form a pyramid. One part is slightly taller than the other. Glue the shorter one on first and then the longer one which will overlap the top edge. Make sure the engraved lines are facing out on the roof. File and sand all the edges so that they are sharp and clean. See Figure 38. Figure 36 Figure 37 Figure 38 16

17 Assemble the two chimneys by gluing the thin chimney sections between the wide ones, using the two small rectangles as braces to keep them square. Glue the small roof cap part onto the larger roof cap part so the two are centered. Glue this on top of the chimney. When dry, file the bottoms of the thin sides to match the angles of the large sides. See Figure 39. Prime and paint the fourteen cast resin dormer parts (6-5). We painted ours very dark grey inside the window area and light grey around it to match our window frames on the rest of the building. We then painted the windows with gloss coat so that they would be shiny. Paint the dormer fronts (6-6) to match the stone of the building. Glue the dormer fronts to the resin dormers so that the bottom are flush and the windows are centered. Sand the backs of the dormers so that they are flat. See Figure 40 Glue the dormers to the roof. The first row of dormers sits on the base of the roof. You can use the lines on the roof to help in placement as they should be symmetrical. Figure 39 Figure 40 The sides of the roof have a slightly steeper pitch and so you will need to sand the backs of the two dormers that go on the sides of the building so that the fronts are vertical. Use Figure 41 for placement. Glue the chimneys to the top of the roof. Use Figure 41 for location. Figure 41 17

18 Assembling the Units Now that you have built all of the building units, it is time to assemble them. Make sure that the bottom and top of each unit is perfectly flat and smooth. Sand or file any imperfections off as necessary. It will be easier to glue the units together upside down. Begin with Unit 5 upside down on your work table and glue Unit 4 to it upside down as well. You can run a bead of glue along the cornice where the two pieces meet. Continue gluing the units together in this fashion making sure that everything is straight and true as you go along. When finished you will have to turn the building back right side up in order to glue on the roof unit. Once completed touch up any glue and paint imperfections along the cornices. Paint the provided sidewalk concrete and put in place. Your building is finished and ready to install on your layout. You may add lights and other details. We thank you for purchasing this kit from CMR and hope that you have enjoyed building it. Be sure to see our other kits at 18

19

20

21

22

The Park Hotel Instructions for Assembly of N Scale Kit

The Park Hotel Instructions for Assembly of N Scale Kit The Park Hotel Instructions for Assembly of N Scale Kit Kit Contents: 198 ea. Laser Cut Acrylic Parts, 2 ea. Chimney Parts Sheets, 1 ea.2".040 styrene rod, 5 ea. Sidewalk Parts, 14 ea. Cast Resin Dormers,

More information

The Midtown Apartment Building

The Midtown Apartment Building The Midtown Apartment Building Instructions for Assembly of The Midtown Apartment Building. Kit Contents: 70 each laser cut acrylic parts. 3 each sidewalk parts. 3each Window Glass Templates, 3 each Window

More information

The Saint Paul Building

The Saint Paul Building The Saint Paul Building Instructions for Assembly of The Saint Paul Building. Kit Contents: 65 each laser cut acrylic parts. 1 each sheet of AC roof unit parts. 1 each sidewalk. 3 each Window Glass Templates,

More information

Donaldson s Department Store

Donaldson s Department Store Donaldson s Department Store Instructions for Assembly of Donaldson s Department Store Kit Contents: 80 each laser cut acrylic parts. 1 each sheet of canopy parts. 1 each sheet of AC roof unit parts. 1

More information

The Fyfe Building Instructions for Assembly of the N scale kit.

The Fyfe Building Instructions for Assembly of the N scale kit. The Fyfe Building Instructions for Assembly of the N scale kit. Kit Contents: 150 each laser cut 1/16" acrylic parts. 6 each 020 adhesive backed part 6 each column caps 2 each decorative canopy 1 each.125"

More information

Fidelity & Guaranty Building

Fidelity & Guaranty Building Fidelity & Guaranty Building N Scale Model Kit Instructions for Assembly of the Fidelity & Guaranty Building Kit Contents: 69 each laser cut acrylic parts. Sidewalk material 1 each Window Glass Templates

More information

Fidelity & Guaranty Building

Fidelity & Guaranty Building Fidelity & Guaranty Building Instructions for Assembly of the Fidelity & Guaranty Building Kit Contents: 69 each laser cut acrylic parts. 1 each sheet of AC roof unit parts. 1 each sidewalk base. 4 each

More information

Hotel Belvedere Instructions for Assembly of the HO scale kit. v1.1

Hotel Belvedere Instructions for Assembly of the HO scale kit. v1.1 Hotel Belvedere Instructions for Assembly of the HO scale kit. v1.1 Kit Contents: 319 ea. laser cut.090" acrylic parts. 132 ea. laser cut.060" acrylic parts. 8 ea. window glass templates 8 ea. window glazing

More information

The Rubley Building Instructions for Assembly of the N scale kit. v1.1

The Rubley Building Instructions for Assembly of the N scale kit. v1.1 The Rubley Building Instructions for Assembly of the N scale kit. v1.1 Kit Contents: 197 ea. laser cut 1/16" acrylic parts. 1ea. adhesive backed.020 styrene part. 10 ea..060 x 1" styrene alignment pins.

More information

The Severn Instructions for Assembly of the N scale kit.

The Severn Instructions for Assembly of the N scale kit. The Severn Instructions for Assembly of the N scale kit. Kit ontents: 172 each laser cut 1/16" acrylic parts 102 each adhesive backed styrene parts 1 each cast entryway 3 each cast balcony 4 each cast

More information

Drawings of all parts have been included for ease of part identification.

Drawings of all parts have been included for ease of part identification. Acme Corporation Instructions for Assembly of the HO Scale Acme Corporation HO Kit Contents: 156 ea. white 1/16" laser cut acrylic part 10 ea. white 1/8" laser cut acrylic part 37 ea. adhesive-backed brick

More information

Instructions for Assembly of the HO Scale The Charles

Instructions for Assembly of the HO Scale The Charles The Charles Instructions for Assembly of the HO Scale The Charles HO Kit Contents: 337 ea. white 1/16" laser cut acrylic part 19 ea. Clear 1/16" laser cut acrylic part 69 ea. white 1/8" laser cut acrylic

More information

If by chance a part is missing or broken please contact us indicating the kit name and part description and we will send you a replacement.

If by chance a part is missing or broken please contact us indicating the kit name and part description and we will send you a replacement. Six Stall Roundhouse Instructions for Assembly of the HO Scale Six Stall Roundhouse Roundhouse Kit Contents: 18ea. Roof Pieces 12 ea. 1/16" Parts Sheets 9ea. 1/8" Parts Sheets 12ea. Floor Pieces 1ea. 1/4"

More information

Hardee s Restaurant kit in HO scale

Hardee s Restaurant kit in HO scale Hardee s Restaurant kit in HO scale Parking lot base and cars not included This kit includes all building parts milled in white styrene plastic and laser cut white acrylic, clear acrylic window glazing,

More information

Nanton Grain Mill Assembly

Nanton Grain Mill Assembly ( 1 ) Nanton Grain Mill Assembly Locate package for assembling storage building. These are cut from 1/8 masonite. Inspect and lightly sand edges where it will be bonded. Use white glue or CA glue to bond.

More information

CVS Pharmacy kit in HO scale

CVS Pharmacy kit in HO scale CVS Pharmacy kit in HO scale Parking lot base and cars not included This kit includes all building parts and wall-mounted signs milled in white styrene plastic, clear window glazing and pre-cut Plastruct

More information

Tools and Tips: ( 1 )

Tools and Tips: ( 1 ) Tools and Tips: As you build instructions will show in my many picture manual how to assemble. You can use your own methods as you desire, my results are very good. A smooth, flat work surface is very

More information

The Hamlin Assembly Instruction By Laser Dollhouse Designs

The Hamlin Assembly Instruction By Laser Dollhouse Designs The Hamlin Assembly Instruction By Laser Dollhouse Designs NOTE 1: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and fit. This also gives

More information

Railroad Kits PO Box 461 Holden, MA

Railroad Kits PO Box 461 Holden, MA (Formerly Downtown Deco DD 1004 Fallburg Station) HO Scale. Thanks for purchasing one of my kits. Because different people have different degrees of experience, I'll walk you through, step by step, explaining

More information

Tools and Tips: ( 1 )

Tools and Tips: ( 1 ) Tools and Tips: As you build the book will show in my many picture manual how to assemble. You can use your own methods as you desire, but these worked best for me. A smooth, flat work surface is very

More information

The Lansdowne One Car Garage Assembly Instruction by Laser Dollhouse Designs

The Lansdowne One Car Garage Assembly Instruction by Laser Dollhouse Designs The Lansdowne One Car Garage Assembly Instruction by Laser Dollhouse Designs NOTE 1: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and

More information

Tools and Tips: ( 1 )

Tools and Tips: ( 1 ) Tools and Tips: As you build instructions will show in my many picture manual how to assemble. You can use your own methods as you desire, my results are very good. A smooth, flat work surface is very

More information

SUGAR CREEK HOTEL PHOTO REAL BUILD KIT

SUGAR CREEK HOTEL PHOTO REAL BUILD KIT SUGAR CREEK HOTEL PHOTO REAL BUILD KIT by Innovative Hobby Supply INSTRUCTIONS FOR: Kit BK 6407 Sugar Creek Hotel Build Kit ~ S scale Free replacement parts are available simply by calling 866 712 4059.

More information

Ben Franklin 5&10 Store

Ben Franklin 5&10 Store Ben Franklin 5&10 Store RIVER LEAF MODELS, LLC RIVER LEAF MODELS, LLC Thank you for purchasing the Ben Franklin 5&10 structure kit. Your kit includes everything you need to assemble the final product.

More information

Allied Tool is a freelance model of a small manufacturing company that grew from production in a home basement to a new building. Assume a gentleman starts assembling gauges in his basement and the business

More information

Taco Bell Restaurant kit in HO scale

Taco Bell Restaurant kit in HO scale Taco Bell Restaurant kit in HO scale Parking lot base and cars not included This kit includes all building parts milled in white styrene plastic, clear window glazing, Plastruct tile roofing, and logo

More information

Corona Concepts presents The Lily All Wood Dollhouse. Instructions and Assembly Guide

Corona Concepts presents The Lily All Wood Dollhouse. Instructions and Assembly Guide Corona Concepts presents The Lily All Wood Dollhouse Instructions and Assembly Guide Introduction In Short... Welcome to the exciting world of dollhouses and miniatures. Since the first tab and slot die-cut

More information

Instructions and Assembly Guide

Instructions and Assembly Guide Corona Concepts presents The Creekside Cabin All Wood Dollhouse 1997 Corona Concepts Schenevus, NY 12155 All rights reserved These instructions were printed in New York State Instructions and Assembly

More information

3Insert the second rod no. 4

3Insert the second rod no. 4 Yamato: Step-by-step 37 The stern block and searchlight control towers a b c d e f Recommended tools and materials Wood glue Sandpaper (no. 800 grain) Metal file Putty Craft knife For metal: Super Glue

More information

The Gothic Chess Set

The Gothic Chess Set The Gothic Chess Set Please note that this chess set is a fairly difficult and time consuming project. I strongly suggest building one or two easier models before tackling this one! The miniatures used

More information

DAVENPORT DEPARTMENT STORE PF5214

DAVENPORT DEPARTMENT STORE PF5214 1:160 BUILDING KIT DAVENPORT DEPARTMENT STORE PF5214 Dress up your downtown scene with the classic Victorian architecture and large first-floor picture windows of the Davenport Department Store. Details

More information

Shell Gas Station & Convenience Store kit in HO scale

Shell Gas Station & Convenience Store kit in HO scale Shell Gas Station & Convenience Store kit in HO scale Parking lot base and cars not included This kit includes all building parts and signs milled in white and black styrene plastic, clear window glazing,

More information

Continued on next page

Continued on next page Please read these instructions completely through to be sure you are familiar with all the steps. Then following along again as you build your structure. Download a.zip file of all the pictures including

More information

Building the Bell Tower

Building the Bell Tower Building the Bell Tower Mold #55 does not contain all of the blocks to build this tower. You will need extra regular blocks (1/2" x 1/2" x 1") and square blocks (1/2" x 1/2" x 1/2"). These blocks can be

More information

Craftman One Car Garage Assembly Instruction by Laser Dollhouse Designs

Craftman One Car Garage Assembly Instruction by Laser Dollhouse Designs Craftman One Car Garage Assembly Instruction by Laser Dollhouse Designs NOTE 1: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and fit.

More information

5If the protruding part is. 6Place 1 as is shown in the. 7Place what was assembled

5If the protruding part is. 6Place 1 as is shown in the. 7Place what was assembled Yamato: Step-by-step 49 The base of the bridge and strakes a c b d a Base of the bridge b Base of the bridge c Base of the bridge d Strakes x 10 THE BASE OF THE BRIDGE 1Smooth 1 to 3, first using the metal

More information

J.W. cobbler 1:160 BUILDING KIT PF5210 WOODLAND SCENICS

J.W. cobbler 1:160 BUILDING KIT PF5210 WOODLAND SCENICS 1:160 BUILDING KIT J.W. cobbler PF5210 The partially assembled walls, positive alignment system and prefinished edges make kit assembly quick, easy and accurate. This three-story brownstone features stacked

More information

Seascape Bungalow Assembly instructions. Laser Dollhouse Designs

Seascape Bungalow Assembly instructions. Laser Dollhouse Designs Seascape Bungalow Assembly instructions Laser Dollhouse Designs NOTE: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and fit. This also

More information

CORNER PORCH HOUSE PF5196

CORNER PORCH HOUSE PF5196 1:87 BUILDING KIT CORNER PORCH HOUSE PF5196 Two-story home with cedar-shake roof and a corner wrap-around porch. Clapboard siding, paned windows, and loaded with accessories, such as a bicycle built for

More information

Building the Cathedral

Building the Cathedral Building the Cathedral Please note that the cathedral is a fairly difficult and time consuming project. I strongly suggest building one or two easier models before tackling this one! Four molds are needed

More information

Building the Circular Tower

Building the Circular Tower Building the Circular Tower You will need to fill this mold 18 times to have enough blocks to build the circular tower. Be sure the blocks are completely dry before gluing them together. For detailed instructions

More information

HARRISON S HARDWARE PF5891

HARRISON S HARDWARE PF5891 1:48 BUILDING KIT HARRISON S HARDWARE PF5891 Model the local hardware store where layout residents can find all they need to keep their homes in tip-top shape and workshops running smooth. The positive

More information

Vivian Mansion Assembly Instruction By Laser Dollhouse Designs

Vivian Mansion Assembly Instruction By Laser Dollhouse Designs Vivian Mansion Assembly Instruction By Laser Dollhouse Designs NOTE 1: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and fit. This also

More information

N Scale Concrete Coal Dock Instruction Manual

N Scale Concrete Coal Dock Instruction Manual N Scale Concrete Coal Dock Instruction Manual 1. General Overview This kit combines precision laser cut acrylic, photo etched brass and wood parts to make a highly detailed model of the Roberts and Schaefer

More information

LASER-ART. The DuBois House. LASER-ARTSTRUCTURES by BRANCHLINE TRAINS BRANCHLINE TRAINS STRUCTURES

LASER-ART. The DuBois House. LASER-ARTSTRUCTURES by BRANCHLINE TRAINS BRANCHLINE TRAINS STRUCTURES LASER-ARTSTRUCTURES by BRANCHLINE TRAINS LASER-ART STRUCTURES by BRANCHLINE TRAINS The DuBois House History With their gingerbread trim and ornate decoration the Queen Anne style is what most people imagine

More information

Modern Gas Station backdrop building kit in HO scale

Modern Gas Station backdrop building kit in HO scale Modern Gas Station backdrop building kit in HO scale This kit includes all building parts, pumps, signs, and base milled in white styrene plastic, clear window glazing, Plastruct Ridgid Clay Tile roofing,

More information

Building the 1, 2, or 3 Car

Building the 1, 2, or 3 Car Building the 1, 2, or 3 Car Garage kit by Railroad Kits. Thanks to Bob Butts for doing the building construction and writing / taking pictures. If this is your first craftsman kit or Railroad Kits purchase

More information

Corona Concepts presents The Laurel All Wood Dollhouse. Instructions and Assembly Guides

Corona Concepts presents The Laurel All Wood Dollhouse. Instructions and Assembly Guides Corona Concepts presents The Laurel All Wood Dollhouse Instructions and Assembly Guides Introduction In Short... Welcome to the exciting world of dollhouses and miniatures. Since the first tab and slot

More information

1Take the keel (3) and

1Take the keel (3) and 1 The hull and the bridge 1Take the keel (3) and apply PVA wood glue in the second slot from the left: a toothpick may make it easier. Take care: the left end is the one that has a projection. THE HULL

More information

After printing these plans, several pages will need to be taped together to form a larger plan. Below is a diagram of which pages need assembled.

After printing these plans, several pages will need to be taped together to form a larger plan. Below is a diagram of which pages need assembled. Watermill Building Plans For complete building instructions and instructional videos, please visit the main web site at www.hirstarts.com/watermill/watermill.html. Using these plans alone will not give

More information

Subway building kit in HO scale

Subway building kit in HO scale Subway building kit in HO scale This kit includes all building parts and signs milled in white and black styrene plastic, clear window glazing, and self-adhesive decals. All parts fit together but may

More information

KIT BUILDING ED SCHULTZ

KIT BUILDING ED SCHULTZ KIT BUILDING ED SCHULTZ KIT BUILDING FIVE BASIC MATERIALS: PLASTIC (STYRENE) WOOD LASER CUT & STANDARD PLASTER METAL RESIN ADDING DETAILS PLASTIC KITS TYPICALLY STYRENE TYPE PLASTIC DPM WALTHERS BACHMANN

More information

Assembly Instructions for Summit Motel Kits # SMFS and SMBD

Assembly Instructions for Summit Motel Kits # SMFS and SMBD Assembly Instructions for Summit Motel Kits # SMFS and SMBD Introduction Thank you for your purchase of the Summit Motel. This modern motel can be converted to almost any chain motel of your choice, depending

More information

Thank you for purchasing E.L. Moore Window & Door.

Thank you for purchasing E.L. Moore Window & Door. Thank you for purchasing E.L. Moore Window & Door. Instructions Version 4.28.15 I ve named this kit after one of the greatest modelers I ve ever known, the late Elliot Moore Jr. Rest in peace my friend.

More information

Roof Contour By Bob Parrish

Roof Contour By Bob Parrish Roof Contour By Bob Parrish This text will show you how to shape the roof contour on Labelle passenger and trolley kits. The height of the clerestory on the two types of kits is different. Passenger kits

More information

Building the Gothic Church

Building the Gothic Church Building the Gothic Church Mold #54 does not contain all of the blocks to build this church. You will need extra regular blocks (1/2" x 1/2" x 1") and square blocks (1/2" x 1/2" x 1/2"). These blocks can

More information

Continue gluing the remaining top parts ensuring the angled piece is glued well. Set aside and let dry. See photo below

Continue gluing the remaining top parts ensuring the angled piece is glued well. Set aside and let dry. See photo below Radiator rev 1.1 The SE5a s radiator is one of the most recognized radiators in WW1. It is one of the components that defines the SE5a. The original SE5a has seen multiple radiator designs used during

More information

Model the hub of your layout s rural setting. Planters Feed and Seed Supply Instructions N Scale 1:160 WOODLAND SCENICS

Model the hub of your layout s rural setting. Planters Feed and Seed Supply Instructions N Scale 1:160 WOODLAND SCENICS PF5201 Planters Feed and Seed Supply Instructions N Scale 1:10 Model the hub of your layout s rural setting. Planters Feed and Seed Supply presents a vintage agricultural center where farmers and rural

More information

Hubble Space Telescope Paper Model Directions Downloads, patterns, and other information at:

Hubble Space Telescope Paper Model Directions Downloads, patterns, and other information at: Hubble Space Telescope Paper Model Directions Downloads, patterns, and other information at: www.hubblesite.org/go/model Materials: model pattern printed onto cardstock/coverstock instructions printed

More information

Domino's Take-out Pizza building kit in HO scale, latest design

Domino's Take-out Pizza building kit in HO scale, latest design Domino's Take-out Pizza building kit in HO scale, latest design This kit includes all building parts and signs milled in white and black styrene plastic, clear window glazing, and self-adhesive decals.

More information

Wayside Cottage Assembly Instructions By Laser Dollhouse Designs

Wayside Cottage Assembly Instructions By Laser Dollhouse Designs Wayside Cottage Assembly Instructions By Laser Dollhouse Designs Parts for assembly Base Floor marked 1A thru 1L 13 post and 11 fences With one gate Walls 1A thru 1L and Alcove roof panels 3 lg and 1 sm

More information

A Day House. A View of One Way to Finish the Exterior of The Day House. Read these instructions all the way through before beginning this project.

A Day House. A View of One Way to Finish the Exterior of The Day House. Read these instructions all the way through before beginning this project. A Day House A View of One Way to Finish the Exterior of The Day House Read these instructions all the way through before beginning this project. General Comments For the purposes of this project, the standard

More information

HRMLaserModels.com T.W. SNOW 25 TON COALING TOWER S SCALE AS USED ON THE MILWAUKEE ROAD

HRMLaserModels.com T.W. SNOW 25 TON COALING TOWER S SCALE AS USED ON THE MILWAUKEE ROAD HRMLaserModels.com T.W. SNOW 25 TON COALING TOWER S SCALE AS USED ON THE MILWAUKEE ROAD HRM-61 S SCALE COAL TOWER T.W.Snow 25 Ton Coaling Tower General Instructions Check out HRMLaserModels.com for construction

More information

Small 45 Roof Houses 1 or 2 Story 1 /24 th Scale Patterns

Small 45 Roof Houses 1 or 2 Story 1 /24 th Scale Patterns BA GARDEN TOWNS 45 Roof Houses 10" x 10" 1 or Story Scaled and easy to read patterns and instructions for wood houses. Yard and Garden Buildings Compatible with Garden Railroads or a delight for any child's

More information

Model Grandma and Grandpa s cozy cottage, a. Country Cottage Instructions HO Scale 1:87 WOODLAND SCENICS PF5186

Model Grandma and Grandpa s cozy cottage, a. Country Cottage Instructions HO Scale 1:87 WOODLAND SCENICS PF5186 PF586 Country Cottage Instructions HO Scale :87 Model Grandma and Grandpa s cozy cottage, a young family s first home or give this vintage Victorian cottage the run-down look of an abandoned shack. This

More information

Little Briana Cottage Dollhouse assembly instructions

Little Briana Cottage Dollhouse assembly instructions Little Briana Cottage Dollhouse assembly instructions NOTE 1: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and fit. This also gives

More information

(56501) Corona Concepts presents The Willow All Wood Dollhouse. Instructions and Assembly Guide RTD AA

(56501) Corona Concepts presents The Willow All Wood Dollhouse. Instructions and Assembly Guide RTD AA (56501) Corona Concepts presents The Willow All Wood Dollhouse Instructions and Assembly Guide RTD10000572AA Introduction In Short... Welcome to the exciting world of dollhouses and miniatures. Since the

More information

DARC MANSION ASSEMBLY INSTRUCTIONS page 1.

DARC MANSION ASSEMBLY INSTRUCTIONS page 1. DARC MANSION ASSEMBLY INSTRUCTIONS page 1. DARC MANSION ASSEMBLY INSTRUCTIONS page 2. NOTE: This project should be printed on heavy card stock. WHAT YOU'LL NEED: Scissors, Elmer's glue (or a glue stick),

More information

1Smooth pieces 4, 5 and 6, using

1Smooth pieces 4, 5 and 6, using Yamato: Step-by-step 109 Machine-guns, anti-aircraft guns and decking h e f a b c g d e f a Anti-aircraft gun base x 2 b Anti-aircraft gun (bottom) x 2 c Anti-aircraft gun (top) x 2 d Machine-gun base

More information

Kristiana Tudor Assembly Instructions By Laser Dollhouse Designs

Kristiana Tudor Assembly Instructions By Laser Dollhouse Designs Kristiana Tudor Assembly Instructions By Laser Dollhouse Designs Parts for assembly Second floor base Third floor base First floor base First floor walls and porch rails Second floor walls Third floor

More information

Instructables Butcher Block Top

Instructables Butcher Block Top Instructables Butcher Block Top Project Overview: This project requires basic woodworking skills and access to woodworking machines. Woodworking machines have sharp cutting edges and are NOT forgiving.

More information

Additional Parts List:

Additional Parts List: THE TIME MACHINE Additional Parts List: In addition to the cast resin parts enclosed in this kit, there should also be a plastic bag containing the following items needed to complete your time machine

More information

Rural Shamrock Gas Station & Store kit in HO scale

Rural Shamrock Gas Station & Store kit in HO scale Rural Shamrock Gas Station & Store kit in HO scale Parking lot base and cars not included This kit includes all building parts and signs milled in white and black styrene plastic, clear window glazing

More information

La Grange, Texas MKT Depot kit in HO scale

La Grange, Texas MKT Depot kit in HO scale La Grange, Texas MKT Depot kit in HO scale This kit includes all building parts laser cut in plywood, white and clear acrylic, and laser cut self-adhesive shingles. All parts fit together but may need

More information

STONEYBRIDGE STRUCTURES

STONEYBRIDGE STRUCTURES 02-208-OO North Eastern Railway N2 Style Signal Box INTRODUCTION Thank you for purchasing one of our products. We hope this information sheet will prove useful in the construction of this model. We have

More information

BUZZ S SAWMILL PF5195 WOODLAND SCENICS BUILDING KIT

BUZZ S SAWMILL PF5195 WOODLAND SCENICS BUILDING KIT 1:87 BUILDING KIT BUZZ S SAWMILL PF5195 Buzz s Sawmill is a detailed work of art with all workings of a vintage steam-fired, belt-driven sawmill. Details include interior rafters and shake roof, attached

More information

EXTREME LOAD no. TWO

EXTREME LOAD no. TWO 1602 - EXTREME LOAD no. TWO Kit Features: 22' 4 " x 14' x 3'-6 Oversize Load 49mm (1.9") actual height Bolt Head Details Welded Load Mounting Fins Painting Handles Tools Required: Hobby Knife Tweezers

More information

WRIGHT FLYER 1 INSTRUCTIONS FOR THE D10LC KIT

WRIGHT FLYER 1 INSTRUCTIONS FOR THE D10LC KIT WRIGHT FLYER 1 INSTRUCTIONS FOR THE D10LC KIT Manufactured in the USA by Easy Built Models PO Box 681744, Prattville, AL 36068-1744 Visit us at www.easybuiltmodels.com Easy Built Models GLUE METHODS Always

More information

FIRE STATION PHOTO REAL BUILD KIT

FIRE STATION PHOTO REAL BUILD KIT FIRE STATION PHOTO REAL BUILD KIT by Innovative Hobby Supply INSTRUCTIONS FOR: Kit BK 4814 Fire Station Build Kit ~ O scale Free replacement parts are available simply by calling 866 712 4059. Includes

More information

Corona Concepts presents The Buttercup All Wood Dollhouse. Instructions and Assembly Guides

Corona Concepts presents The Buttercup All Wood Dollhouse. Instructions and Assembly Guides Corona Concepts presents The Buttercup All Wood Dollhouse Instructions and Assembly Guides Introduction In Short...Welcome to the exciting world of dollhouses and miniatures. Since the first tab and slot

More information

Darjeeling Coach 4-Wheel First/Second Class

Darjeeling Coach 4-Wheel First/Second Class Darjeeling Coach 4-Wheel First/Second Class Introduction This kit was designed in 16mm scale from early Darjeeling drawings and photographs. It uses brass castings available from Brandbright. The instructions

More information

Cobra X Q Construction Tips Construction: Bel y pan

Cobra X Q Construction Tips Construction: Bel y pan Cobra X Q Construction Tips : The white plastic in this kit is high impact styrene. It can be painted with most types of coatings if light coats are applied this is necessary due to the thickness of the

More information

Hegeler Carus Mansion Assembly Instructions By Laser Dollhouse Designs

Hegeler Carus Mansion Assembly Instructions By Laser Dollhouse Designs Hegeler Carus Mansion Assembly Instructions By Laser Dollhouse Designs Parts for assembly 2 nd floor base 3 rd floor base 1 st floor base 4 th floor base Lower roof panel Mid roof panel Upper roof panel

More information

(Build Instructions)

(Build Instructions) (Build Instructions) Specifications * Wingspan: 58cm * Length: 50cm * Flying Weight: 59 grams * Channels: 3 (Rudder Elevator Throttle) * Suggested Receiver: 4Ch Micro * Motor: 8mm GearDrive * Prop: GWS

More information

Small Town Buildings. Scaled and easy to read patterns and instructions. Shoe / Western Union (with and without porch)

Small Town Buildings. Scaled and easy to read patterns and instructions. Shoe / Western Union (with and without porch) 1 /24 th Scale Patterns kiva design G R O U P E 1 Story Flat Roof Yard and Garden Buildings Compatible with Garden Railroads or a delight for any child's collection Overall Dimensions Foundation: 10" x

More information

Hubble Space Telescope Expert Model Interior Directions Downloads, patterns, and other information at:

Hubble Space Telescope Expert Model Interior Directions Downloads, patterns, and other information at: Hubble Space Telescope Expert Model Interior Directions Downloads, patterns, and other information at: Materials: Construction tips: The patterns and instructions, which can be downloaded at. The pattern

More information

CONCEPT MODELS INSTRUCTIONS FOR UP DC-10 WING CAR El Toro Way Stockton, CA Web Address:

CONCEPT MODELS INSTRUCTIONS FOR UP DC-10 WING CAR El Toro Way Stockton, CA Web Address: CONCEPT MODELS Web Address: http://www.con-sys.com 8810 El Toro Way Stockton, CA 95210 INSTRUCTIONS FOR UP DC-10 WING CAR 2 CONCEPT MODELS PARTS DC-10 WING CAR Item No. Part No. DESCRIPTION QTY. 1 2003-1

More information

Cardboard Model Buildings

Cardboard Model Buildings Cardboard Model Buildings Get more model kits from http://www.modelbuildings.org PRINTING & ASSEMBLY TIPS: These OO designs can easily be resized by reducing the print percentage as follows: OO scale is

More information

How to assemble the Reims Gueux Pit Centre Module #005

How to assemble the Reims Gueux Pit Centre Module #005 How to assemble the Reims Gueux Pit Centre Module #005 We recommend quick drying super glue for our models. Just a few drops on the joining edges, press and hold them for a few seconds and the connection

More information

RoR Step-by-Step Review * Boot Hill Express 1:24 Scale Monogram Kit # Review

RoR Step-by-Step Review * Boot Hill Express 1:24 Scale Monogram Kit # Review RoR Step-by-Step Review 20130506* Boot Hill Express 1:24 Scale Monogram Kit #85-4999 Review This is what happens when you combine a dragster with an exceptionally ornate hearse. The beautiful wood lines

More information

7/8n2 Scale Plantation Coach

7/8n2 Scale Plantation Coach 7/8n2 Scale Plantation Coach Introduction This small coach modeled in 7/8 n2 was inspired from a Hawaiian Railway Company plantation excursion car from the late 19 century. While not an exact replica,

More information

The Rowen Victorian Assembly Instructions By Laser Dollhouse Designs

The Rowen Victorian Assembly Instructions By Laser Dollhouse Designs The Rowen Victorian Assembly Instructions By Laser Dollhouse Designs Parts Listing 1. Four main floors A. Base Floor with markings S1 thru S6 B. 1 st Floor with markings 1A thru 1H C. 2 nd Floor with markings

More information

How to assemble the Reims Gueux Pit End Modules #005

How to assemble the Reims Gueux Pit End Modules #005 How to assemble the Reims Gueux Pit End Modules #005 Depending on which kit you have purchased you will either have a pair of end sections, some centre sections or both. We will describe building of the

More information

Cockpit Kit. Full Depth - Builds Quickly - Light Weight READ THROUGH THIS INSTRUCTION MANUAL FIRST. IT CONTAINS IM- laser cut wood kit

Cockpit Kit. Full Depth - Builds Quickly - Light Weight READ THROUGH THIS INSTRUCTION MANUAL FIRST. IT CONTAINS IM- laser cut wood kit The Savage Light Sukhoi Su- 27 Cockpit Kit contains everything you need to build a full depth semi scale Su-27 cockpit, yet adds less than an ounce to your finished model s weight (not including pilot).

More information

Dura-Lock Roof System

Dura-Lock Roof System DLR-14 Dura-Lock Roof System Assembly and Installation Instructions Read the instructions before starting the job. They explain the steps required to produce a finished product that will meet factory specifications.

More information

RACETRACK BLEACHERS PHOTO REAL BUILD KIT

RACETRACK BLEACHERS PHOTO REAL BUILD KIT RACETRACK BLEACHERS PHOTO REAL BUILD KIT by INSTRUCTIONS FOR: Kit BK 6402 Racetrack Bleachers Build Kit ~ S scale Free replacement parts are available simply by calling 866 712 4059. Includes two (2 ea.)

More information

Pier 1 Imports backdrop building kit in HO scale

Pier 1 Imports backdrop building kit in HO scale Pier 1 Imports backdrop building kit in HO scale Parking lot base and cars not included This kit includes all building parts and signs milled in white and black styrene plastic, clear window glazing, logos

More information

BUILDING ST. MARTIN S CORNER GAS & GROCERIES By RAILROAD KITS

BUILDING ST. MARTIN S CORNER GAS & GROCERIES By RAILROAD KITS Thank you for purchasing this kit. I need to first thank Bob Butts for building the pilot model, and most of all for this wonderful set of instructions. 32 pages. Over 110 super color photos documenting

More information

The Reading Tug Schuylkill By: Barry Hensel

The Reading Tug Schuylkill By: Barry Hensel The Reading Tug Schuylkill By: Barry Hensel My Reading Lines Central Division layout has needed a tug boat for the Port Richmond coal dock scene for some time. I finally found a Walthers Tug kit for a

More information

28 ft. Ventilated (Combination) Box Car

28 ft. Ventilated (Combination) Box Car 28 ft. Ventilated (Combination) Box Car Introduction This laser cut wood kit is an HO scale model of a 28 ft. Ventilated (also known as a Combination) Box Car. The model is based on the Illinois Central

More information