Riff Tables RIFF-NIC, BAR HEIGHT AND TENNIS TABLE ASSEMBLY INSTRUCTIONS

Size: px

Start display at page:

Download "Riff Tables RIFF-NIC, BAR HEIGHT AND TENNIS TABLE ASSEMBLY INSTRUCTIONS"

Elfreda Britney Todd
5 years ago
Views:

1 Riff Tables RIFF-NIC, BAR HEIGHT AND TENNIS TABLE ASSEMBLY INSTRUCTIONS

2 84" & 72" LONG RIFF TABLE COMPONENTS Top QTY 2 Leg Assembly 2 3 Support Assembly 4 Cross Rail 5 Brace /Leveler 4 7 #8 x 2 ½" Pan Head Screws (HK-0) 0 8 #8 x 2" Pan Head Screws (HK-02) 4 9 #8 x ½" Pan Head Screws (HK-03) 4 0 #8 x ¼" Pan Head Screws (HK-04) 8 #8 x 5/8" Pan Head Screws (HK-05) Riff Tables by OFS Assembly Instructions Page 2 of 7

3 96" & 08" LONG RIFF TABLE COMPONENTS Top QTY 2 Leg Assembly 2 3 Center Leg Assembly 4 Support Assembly 5 Cross Rail-Under 6 Cross Rail-Over 7 Brace /Leveler 6 9 #8 x 2 ½" Pan Head Screws (HK-0) 3 0 #8 x 2" Pan Head Screws (HK-02) 6 #8 x ½" Pan Head Screws (HK-03) 4 2 #8 x ¼ Pan Head Screws (HK-04) 6 3 #8 x 5/8 Pan Head Screws (HK-05) Page 3 of 7 Riff Tables by OFS Assembly Instructions

4 STEP. Place Worksurface, bottom side up, on a non-marring surface. 2. Align Notches and slide Under Top Assembly onto Center Base (96" and 08" long tops only). 3. Connect End Bases to Under Top Assembly by inserting Tennons into mortises. 4. Secure Bases to Under Top Assembly with #8 x 5/8" Pan Head Screws (HK-05). Center base Base (96" & and 08" 08" tops) tops) End base Base Under top Top assembly Assembly Mortise Tennon Notches 96" and & 08" long tops only Riff Tables by OFS Assembly Instructions Page 4 of 7

5 STEP 2. Fit Cross Rail Angled Tennons into Mortise on bottom of Base Rail. 2. Straight Tennons fit on top and bottom of Center Base Rail (96" and 08" long tops only). 3. Secure Angled Tennons with #8 x ½" Pan Head Screws (HK-03). 4. Secure Straight Tennons with (2) #8 x 2" Pan Head Screws (HK-02). Straight Tennon tennon Align Align holes holes with with holes holes in in base Base rail Rail Angled Angled Tennon tenn Mortise 96" 96" and & 08" long tops only Page 5 of 7 Riff Tables by OFS Assembly Instructions

6 STEP 3. Install Braces by inserting Tennon into Mortise. 2. Bottom edge of Brace should rest flush on Cross Rail. Cross Rail rail Mortise Tennon Brace Secure Secure Brace Brace to Mount to Mount plate Plate with with #8 #8 x 2" x 2" pan Pan head Head screws Screws (HK-02). (HK-02). Secure Secure Brace to Brace Cross to rail Cross with Rail with #8 x #8 2 /2" x 2 ½" pan Pan head Head screws Screws (HK-0) (HK-0). Riff Tables by OFS Assembly Instructions Page 6 of 7

7 STEP 4. Turn Base over and place in desired location. 2. Make Base level by adjusting Levelers. 3. Place Worksurface on Base and position so it is centered both directions. Center on on base Center on on base base Cleat L-Bracket 4. Secure Worksurface to Base by screwing Secure Work surface to base by #8 x 5/8 Pan Head Screws (HK-05) through screwing #8 x 5/8" pan head screws the L-Brackets. (HK-05) through the L-Brackets. 5. Use Use #8 x #8 ¼ x Pan /4" Head pan Screws head (HK-04) screws to secure (HK-04) Cleats to to secure Worksurface. cleats to work surface. Use #8 x 2 /2" pan head screws (HK-0) 6. Use #8 to x secure 2 ½ Pan bases Head to Screws work (HK-0) surface. to secure Bases to Worksurface. #8 x /4" ¼" #8 x 2/2" ½" #8 x 5/8" Page 7 of 7 Riff Tables by OFS Assembly Instructions

8 PART # INSTRUCTION SHEET # 2545INS Riff Tables RIFF-NIC, BAR HEIGHT AND TENNIS TABLE ASSEMBLY INSTRUCTIONS an OFS Brands company 204 East Sixth Street Huntingburg, IN ofs.com 0.5

IMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the

IMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the PART # 1608990 STATIC BRIDGE & RETURN MODULE 1. This sheet covers the steps to install a static bridge or return module with the FX no hinged access panel back option to a height adjustable freestanding