#11179 Wellington ARBOR
|
|
- Brook Tucker
- 5 years ago
- Views:
Transcription
1 #11179 Wellington ARBOR Assembly INSTRUCTIONS TOOLS NEEDED Tape Measure Variable Speed Drill with #2 Phillips Bit (recommended) or Phillips Screwdriver Hammer or Mallet ARBOR SIDE PANEL ASSEMBLY (Refer to Drawing 1) (Make 2) On clean flat surface lay one 2 x 2 x 88 left post with the side with the eight routed holes facing up and the screw pilot holes facing you. Starting at the bottom of the post, insert one ⅞ x 1½ x 27½ outside cross rail (2 holes in one side) in the bottom hole. In the next two holes up from the bottom, insert two ⅞ x 1½ x 27½ inside cross rails (4 holes in one side, 2 holes in the other) with the 4 holed sides facing one another. Leaving the next two holes empty, insert two more ⅞ x 1½ x 27½ inside cross rails with the 4 holed sides facing one another. Insert a second ⅞ x 1½ x 27½ outside cross rail in the last hole. Using four of the 1 x 1 x 26½ rails, slide each through the outer most 1 x 1 holes in two inside rails and into the outside rail. (Refer to Drawing 2) Insert two ⅞ x 1½ x 27½ middle rails into the two remaining holes in the post, sliding the free end of each 1 x 1 x 26 rail into the middle rail. Set one 2 x 2 x 88 right post on top of the previous assembly and insert each rail into the routed holes. Flex the two inside cross rails to slide two 1 x 1 x 16 ¾ rails into the open holes. Do this on both the top and bottom of the side panel. Similarly, flex the two middle rails to slide two 1 x 1 x 12¾. Make sure all parts are inserted completely into both posts and fasten with ¾ screws. Snap screw caps over screw heads. ARBOR TOP ASSEMBLY (Refer to Drawing 3) Lay both side panels on there edge approximately 50" apart, with screw heads facing out and routed holes for corner braces facing in. Insert one of the 7/8 x 1 ½ x 18 corner brace pieces into the bottom side of the 1 ½ x 4 x 72 top rail. Working with the side closest to you, slide the 1 ½ x 4 x 72 top rail into the 4" slot on the top of the post. As you slide the top rail into its hole in the post, insert the corner brace into the 7/8 x 1 ½ hole routed in the post. Do the same procedure for opposite end of 72" rail. Flip arbor over and repeat for other 72" rail. The measurement from the longest peak of top rail to the outside of the 2 x 2 leg should be 9. Make sure measurement of top rail is correct on both sides. Using 1 ¼ screws fasten corner braces, top rail and side panels together, snap screw caps over screw heads. Lay the 7/8 x 1 ½ x 41 top cross rails into place on top of the top rails, using the pilot holes for screws as your guide. Fasten each top cross rails using 1 ¼ screws and snap screw caps over screw heads. Dura-Trel Inc. ~ PO Box 122, Sheboygan Falls, WI ~ Toll Free
2 FINISHING TOUCHES Apply glue to the inside edges of the 5 3/8 end caps and push them onto the ends of the 72" rails; do not slide from ends. Apply glue to inside edges of the 2 x 2 post caps for arbor posts; the arrowhead caps for on top of 1 x 1 square rails and the 7/8 x 1 ½ end caps for top cross rails on arbor top. Arbor is now ready for installation. If you encounter missing or defective parts, please call manufacturer direct at the toll free # below. Dura-Trel Inc. ~ PO Box 122, Sheboygan Falls, WI ~ Toll Free
3
4
5
6 2 sq. post arbor ground anchor Assembly & installation Instructions Parts List: Description Qty 16 L-channel Ground Anchor 4 1 Self-tapping White-head Screws 8 Option 1 (soft ground) Slide one 16 steel L-channel ground anchor into bottom of each post. Slide ground anchor up to bottom cross rail. Using two 1 selftapping white-head screws per post, screw post to ground anchor (figure 1). When fastening, use one screw per side where ground anchor meets post. For added support fasten screws with at least two inches vertically between them. Option 2 (hard ground) Measure distances between posts and mark ground accordingly. Pound 16 steel L-channel ground anchors into ground according to measurements and basic layout (figure 2), leaving about 4 inches of ground anchor exposed. When pounding into ground, use block of wood to prevent ground anchor from bending. Slide arbor over ground anchors. Using two 1 self-tapping white-head screws per post screw post to ground anchor (figure 1). When fastening, use one screw per side where ground anchor meets post. For added support fasten screws with at least two inches vertically between them. Option 3 (permanent installation) FIGURE 1 Ground Anchor Assembly FIGURE 2 Ground Anchor Basic Installation Layout Measure distances between posts and mark ground accordingly. Dig holes 12 deep according to measurements and basic layout (figure 2). Fill with cement and place 16 steel L-channel ground anchors in wet cement. Be sure that ground anchors are straight and in accordance with measurements of arbor posts. Allow cement to dry. NOTE: There is very little room for error with this installation method. Slide arbor over ground anchors. Using two 1 self-tapping white-head screws per post screw post to ground anchor (figure 1). When fastening, use one screw per side where ground anchor meets post. For added support fasten screws with at least two inches vertically between them.
#11179 Wellington ARBOR
#11179 Wellington ARBOR Assembly INSTRUCTIONS TOOLS NEEDED Tape Measure Variable Speed Drill with #2 Phillips Bit (recommended) or Phillips Screwdriver Hammer or Mallet ARBOR SIDE PANEL ASSEMBLY (Refer
More information#11178 Providence ARBOR
#11178 Providence ARBOR ASSEMBLY INSTRUCTIONS TOOLS NEEDED Drill with #2 Phillips Bit (recommended) or Phillips Screwdriver Ruler Hammer or Mallet ARBOR TOP ASSEMBLY (Refer to Drawing 1) (Make 2) On clean
More informationWindsor Arbor. Parts List: General Information: Tools required: Assembly & installation Instructions
Windsor Arbor Assembly & installation Instructions Parts List: General Information:» Read through carefully before beginning assembly.» When assembling components, place on a clean, flat, non-abrasive
More informationQueensbrook Pergola. General Information. Tools Required. Model# Assembly Instructions. Qty
Queensbrook Pergola Model# 11301 Assembly Instructions General Information PLEASE READ THROUGH BEFORE BEGINNING ASSEMBLY. IMPORTANT: Check boxes for Contents Listed Check inside of parts as some parts
More informationThe Newport Arbor ASSEMBLY INSTRUCTIONS. Material You Will Need (Not Included) 4 in x 4 in x 4 ft Pressure Treated Lumber (4)
ASSEMBLY INSTRUCTIONS in in / in / in 0 in in in in Please read through before starting assembly. IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS. Check Box for These Contents In the event
More informationCottage Picket Gate. 6 in in in in
S S E M LY I N S T R U T I O N S www.newenglandarbors.com ottage Picket Gate 1.875 in 6 in 43.75 in 22.5 in 2 48.5 in Please read through before starting assembly. heck ox for These ontents (1 ox) In the
More informationThe Devonshire Arbor 85 in
ASSEMBLY INSTRUCTIONS in in in in in Please read through before starting assembly.. in IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS. Check Box for These Contents In the event of missing
More informationThe Nantucket Legacy Arbor
SSEMLY INSTRUTIONS The Nantucket Legacy rbor Please read through before starting assembly. IMPORTNT: HEK THE INSIDE OF YOUR POSTS FOR LL MTERILS. heck ox for These ontents In. the Keystone event of missing
More informationThe Camden Privacy Screen
ASSEMBLY INSTRUCTIONS The Camden Privacy Screen 0 5/8 in (66 cm) 7 / in (8 cm) 6 / in (6.5 cm) 90 in (9 cm) Post 66 in (68 cm) 78 in (98 cm) Please read through before starting assembly. IMPORTANT: CHECK
More informationThe Nantucket Legacy Arbor
ASSEMBLY INSTRUCTIONS 0. in 9 in 0. in 68 in 7 in in *Nantucket Legacy with Trim Kit Shown Above. Please read through before starting assembly. in 60 in 0 in 8 in IMPORTANT: CHECK THE INSIDE OF YOUR POSTS
More informationPlayground Assembly Instructions
Before You Begin Playground Assembly Instructions Locate the playground set on firm, level ground. Assemble the playground on or close to its permanent location Two people are recommended to assemble the
More informationWalk-in Configurations
Walk-in Configurations Includes Wall-to-Open, Corners, and Corner Rounder Bars INSTALLATION INSTRUCTIONS Tools needed: Tape measure, level, pencil, #2 Phillips head screw driver or power drill with a 6"
More informationHow To Measure Your Finished Opening
3000 Series Bifold Doors How To Measure Your Finished Opening MEASURE FROM RIGHT TO LEFT 2 PLACES (WIDTH) MEASURE FROM TOP TO BOTTOM 2 PLACES (HEIGHT) Tools Required for Assembly: Tools Needed: Phillips
More informationSECTION 19: Endwood Fusion Welded Gate Installation Guide
SECTION 19: Endwood Fusion Welded Gate Installation Guide ASSEMBLY AND INSTALLATION FOR: Fusion Welded Gates Gate Frame with Full Size Pickets Privacy & Board on Board California & Shadowbox Gate width
More information10x10 Trellis Pergola
0x0 Trellis Pergola ASSEMBLY GUIDE Ver.-007 Table of Contents PAGE 0x0 Trellis Pergola Introduction & Overview...................................................... Pergola Materials Overview..............................................................
More informationThe Westchester Arbor
A S S E M B LY I N S T R U C T I O N S 9. in 90 in. in 0 in in 0 in in Please read through before starting assembly. Check Box for These Contents In the event of missing or defective parts please call
More information10x10 Trellis Pergola
0x0 Trellis Pergola ASSEMBLY GUIDE Ver.0-7 Table of Contents PAGE Introduction & Overview...................................................... Pergola Materials Overview..............................................................
More informationCABINETRY Assembly Instructions
www.hdicabinetry.com Assembly Instructions TABLE OF CONTENTS Category Page(s) Section 1: Framed Series Base Cabinet Instructions Wall Cabinet Instructions Easy Reach Cabinet Instructions 1.01-1.04 1.05-1.06
More informationCottage Picket Gate A S S E M B LY I N S T R U C T I O N S
S S E M LY I N S T R U T I O N S ottage Picket Gate 1 7/8 6 43 3/4 22 1/2 48 1/2 Please read through before starting assembly. heck ox for These ontents (1 ox) In the event of missing or defective parts
More informationEquilibrium. Conference Table. Installation Instruction. Revision B 11/07/16
Equilibrium Conference Table Installation Instruction Revision B 11/07/16 Equilibrium End User Agreement Enwork Equilibrium table bases must be installed directly onto a four inch minimum thickness concrete
More informationThe Vienna Trellis. Tools You Will Need. General Information
A S S E M B LY I N S T R U C T I O N S www.newenglandarbors.com 8.7 in 9 in 6 in in Please read through before starting assembly. in 9 in IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS. Check
More informationInstallation Instructions for. Handrail Component System
Handrail STEP-BY-STEP Installation Instructions for Handrail Component System Rise in Inches Run in Inches 8 8.5 9 9.5 10 10.5 11 11.5 12 12.5 13 13.5 14 14.5 15 8.5 47 45 43 42 40 39 38 36 35 34 33 32
More informationFigure 1. RAILING INSTALLATION The following instructions describe the installation of three types of railing sections: Line, Stair, and Angled
Veranda Railing System Veranda railing systems are designed to work with a number of different decking materials and surfaces. Before initiating any project, obtain a copy of your local building codes
More informationLaminate Cabinet Installation Instructions
Laminate Cabinet Installation Instructions www.easygaragestorage.com/installation How To Use These Instructions Thank you for your purchase! Please read each step of this manual thoroughly to ensure proper
More informationRipple Hanger ASSEMBLY INSTRUCTIONS
Ripple Hanger ASSEMBLY INSTRUCTIONS RIPPLE HANGER Recommended Tools Drill with 1/8, 1/4, and 1/2 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket
More informationPVC Fencing Install Instructions
PVC Fencing Install Instructions Step 1-Pounding the Galvanized Steel Posts Call your local area utility company to come mark underground lines before any digging or pounding any posts into the ground.
More informationTrack Rack. * Track Racks are not lockable
The Track Rack s unique staggered, sliding hook design creates the greatest parking efficiency while still providing easy access to any particular bike. When adding or removing a bike to the rack, simply
More informationFigure A. Figure B. Figure C. Figure D
Xsite 1 Power/Data Tile and Components Tools Required Tape Measure Cordless Drill/Driver #2 Phillips Screw driver bit Rubber Mallet Flat Blade Screwdriver Figure A Hardware Required Provided as shown Installation
More informationGlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationThe Fairfield Deluxe Arbor
A S S E M B LY I N S T R U C T I O N S The Fairfield Deluxe Arbor in 9. in in 9. in in Please read through before starting assembly. 0 in 0 in in in IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS TOOLS REQUIRED Rechargeable, variable speed drill 3/8 diameter drill bit 3 Robertson bits #0, #1 and #2 Slot screwdriver Non marring hammer with 1 head Level Caulk or sealant
More informationEASY-IN POOL STEP SYSTEM NE132
EASY-IN POOL STEP SYSTEM NE132 This instruction manual features multiple guides for the step unit components. 7939 EASY POOL STEP (NE113) FOR USE WITH: EASY-IN POOL STEP (NE126) 6492 PARTS & HARDWARE FOR
More informationDowntown Rack. Custom logo option available
Custom logo option available Downtown Rack The Downtown Rack uses thick, square-tube construction that can t be cut with a pipe cutter. The extended width of the Downtown Rack makes for easy bike parking
More informationDura-Lock Roof System
DLR-14 Dura-Lock Roof System Assembly and Installation Instructions Read the instructions before starting the job. They explain the steps required to produce a finished product that will meet factory specifications.
More informationSwerve Rack CUSTOM RACKS AVAILABLE
CUSTOM RACKS AVAILABLE Swerve Rack The design of the Swerve mirrors the bike frame, thus providing superior bike support while making it easy to secure both the bike frame and wheel with a standard u-lock.
More informationAssembly Instructions
18' W x 10' H or 12' H Peak Style Frame Assembly Assembly Instructions Before you start: 2+ individuals recommended for assembly, approximate time 3 hours. Recommended tools: Power Drill, Safety Glasses,
More informationπ H-4408 ALUMINUM BLEACHERS 5-ROW x 15' PARTS uline.com TOOLS NEEDED
π H-4408 1-800-295-5510 uline.com ALUMINUM BLEACHERS 5-ROW x 15' TOOLS NEEDED Square Tape Measure Rivet Gun 3/16" Drill Bit 1/2" Wrench Socket Wrench 1/2" Deep Well Socket #2 Phillips Bit Rubber Mallet
More informationTABLE OF CONTENTS REQUIRED TOOLS
TABLE OF CONTENTS SECTION SECTION TITLE PAGE NO. 1 2 3 4 5 Assembling Mounting Structure Installing Bicycle Supports Mounting Rack to Wall Adding Sections Customizing Rack Configuration REQUIRED TOOLS
More informationPergola Installation Instructions
Pergola Installation Instructions TOOLS REQUIRED HAMMER DRILL 1/2 MASONRY BIT PENCIL DRILL 3/16 DRILL BIT LEVEL SQUARE LADDER WRATCHET & SOCKETS RUBBER MALLET 2 TAPE MEASURE Column/Post Placement Table
More informationRockwell 4-in-1 Sliding Door
Rockwell 4-in-1 Sliding Door ASSEMBLY INSTRUCTIONS ROCKWELL 4-IN-1 SLIDING DOOR Recommended Tools Drill with Phillips Bit Socket Wrench with 7/16 Socket Rubber Mallet Adjustable Square ROCKWELL 4-IN-1
More informationClearview Railing System Installation Instructions
Clearview Railing System Installation Instructions Disclaimer: AGS Stainless, Inc. has its Clearview Railing Systems designed by a professional engineer to meet the requirements of the latest national
More informationAssembly Instructions
Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt
More informationMach Wall Installation Instructions
Mach Wall Installation Instructions Planning the Job Since Mach Wall is an innovative product that accomplishes 3 tasks at the same time (frame, insulate and drywall) and it replaces traditional framing,
More informationMISCELLANEOUS CABINET REPAIRS
MISCELLANEOUS CABINET REPAIRS 167 168 NOTES MISCELLANEOUS CABINET REPAIRS Cabinet Panel Repairs 175 SIDE PANEL REPLACEMENT - GDM SERIES INSTALLATION INSTRUCTIONS Tools Required 1/8" drill Rivet Tool Silicone
More informationResidential & Industrial Fence
Page Residential & Industrial Fence Assembly Instructions Congratulations on the purchase of your new Fence System. Your fence has been designed to give you years of trouble free service with only minimal
More informationELEVEN COLLABORATIVE. CONFERENCE TOPS Assembly Instructions
ELEVEN COLLABORATIVE Table of Contents SUPPORT BRACE ASSEMBLY.... 3 TABLE BASE FRAME ASSEMBLY.... 4 LEG ATTACHMENT.... 5 TOP JOINING PLATE ASSEMBLY... 6 TOP CLAMP/TOP SPACER INSTALLATION.... 7 TOP PLACEMENT
More informationHow to Install Custom Real Wood and Faux Wood Blinds
Before you begin your installation: READ ALL INSTALLATION INSTRUCTIONS! Make sure that you have all tools and hardware needed for installation. Check the installation surface (wall, ceiling, or window
More informationFLEX 48 x 72 / 60 x 72
FLEX 48 x 72 / 60 x 72 SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical
More informationL.L.Bean. Wooden Slat Bed
L.L.Bean Wooden Slat Bed Thank you for purchasing our Slat Bed. Assembly of this product requires A Phillips head screwdriver. We have found it helpful to have a second person present in at least one step
More informationFENCE INSTALLATION GUIDE 8 HIGH WALLS
FENCE INSTALLATION GUIDE 8 HIGH WALLS 1.866.648.9336 www.simtekfence.com INSTALLATION GUIDE These instructions are designed to assist both professional installers and do-it-yourselfers of SimTek decorative
More informationUnder Seat Storage Drawer Installation Instructions
Under Seat Storage Drawer Installation Instructions Parts List: 1) Drawer Assembly 8) Self Tapping Screws 1) Instructions 1) Template Tools Needed: Drill and/or Bit Driver Tape Measure Jigsaw or metal
More informationIf you discover that material is missing or defective, contact our customer service department immediately:
General Information Open the pack list on the crate s exterior. Locate the shop drawings and installation instruction inside the box. Review contents and make sure all parts are present. For a rectangular
More informationVinyl Fence Installation Instructions. Privacy Fence Installation Instructions
Privacy Fence Installation Instructions Tips Before You Start - Read this instruction sheet completely. - During fence assembly, work on a soft, non-abrasive surfaces where possible to avoid - scratching
More informationDeck Mount Installation with Bench
Deck Mount Installation with Bench 1. Mark track with square. 2. Cut tracks with saw. 3. Drill ¼ hole (if needed.) 4. Countersink track. 5. Countersink all track 6. File all track ends. ends. 7. Lay out
More informationNEXUS SERIES CABINETS
NEXUS SERIES CABINETS STANDARD BASE ASSEMBLY INSTRUCTIONS Also applies to: Galaxy Series, Nexus Series, Ridgeline Series, Statesman Series, and Waterford Series FOR YOUR INFORMATION: These assembly instructions
More informationBox Track INSTALLATION INSTRUCTIONS
Box Track INSTALLATION INSTRUCTIONS BOX TRACK Recommended Tools Level Tape Measure Pencil Drill with 1/8, and 1/4, Drill Bits, Phillips Bit and Slotted Bit Socket Wrench with 9/16 Socket 9/16 and 5/8 Wrench
More informationTrendWall Floor-To-Ceiling Panels Installation Instruction
TrendWall Floor-To-Ceiling Panels Installation Instruction TrendWall Components Covered by this Instruction: Crown (and accessories) Floor Plate Solid Panel Filler Panel Wall Channel Door Section Pilaster
More informationGambrel Barn with Overhang Manual
Tools Needed: -Cordless Drill (12V or higher) -#2 Square Drive Bit -Hammer -6 Step Ladder -Tape Measure -Square utility knife w/ blade & hook blade -Speed Square Little Cottage Co. PO Box 455 Berlin, OH
More information129 KITCHEN BASE CABINET 480
129 KITCHEN BASE CABINET 480 There are two sorts of kitchen cabinets: base cabinets, which sit on the floor, and wall cabinets. Base cabinets provide both storage space and work surfaces. They often house
More information2017 UPDATED INSTALLATION INSTRUCTIONS
2017 UPDATED INSTALLATION INSTRUCTIONS with square composite or round metal balusters Manufactured by fiberondecking.com 800.573.8841 Horizon Railing 6 ft. and 8 ft. Installation Instructions Required
More informationMAINSTREET 36 INCH TABLE SOCCER
Mainstreet 36 Inch Table Soccer MAINSTREET 36 INCH TABLE SOCCER Replacement Parts Order direct at or call our Customer Service department at (800) 5-7593 8 am to 4:30 pm Central Standard Time September
More informationTIP FOR GETTING STARTED
Tip for getting started TIP FOR GETTING STARTED Be careful not to drill into any electrical wires, ductwork, plumbing or other damagable components. If you have any questions on the locations of these
More informationHOW TO INSTALL HORIZONTAL ROD RAILING TREX SIGNATURE STANDARD
HOW TO INSTALL HORIZONTAL ROD RAILING NOTES:» Adjust drill power to lowest setting that will drive screw. DO NOT OVER TORQUE 6 STAINLESS STEEL STAINLESS FASTENERS.» NEVER use impact tools on 6 Stainless
More informationO W N E R ' S M A N U A L
TABLE TENNIS TABLE MODEL NOS. T861 T861B O W N E R ' S M A N U A L 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.. Some smaller parts may
More informationArtisan Vinyl Pergola
Artisan Vinyl Pergola Assembly Manual Thank you for your purchase of this Pergola. Beefy Vinyl Pergola Assembly Manual This manual is designed to simplify the assembly process, however we recommend having
More informationResidential & Industrial Fence
Residential & Industrial Fence Assembly Instructions CONTENTS 02: OVERVIEW & CONTENTS 03: PRODUCT SPECIFICATIONS 04: GETTING STARTED 05: WALL ATTACHMENT & LINE POST ASSEMBLY 06: CORNER POST ASSEMBLY 07:
More informationGREENHOUSE 6'x8' ASSEMBLY INSTRUCTIONS. (Internal Dimensions) Overall Dimensions (Approx.) L 193 W 200 H cms 97.5" L 76" W 78.
ASSEMBLY INSTRUCTIONS GREENHOUSE 'x8' (Internal Dimensions) Overall Dimensions (Approx.) 7. L 9 W 00 H cms 97." L 7" W 78.8" H 0 IMPORTANT You must read these instructions carefully before you start to
More informationBIKE FILE (301)
B IK E F I L E High Efficiency The Bike File is our most space efficient u-lock compatible product. Sturdy sliding hangers allow nine bikes to be securely stored in an eight-foot section while allowing
More informationInstallation Instructions
Installation Instructions For Models: Model Number / Description File Name 1540 Classic Series P-Lam Toilet Partitions 1540.pdf 1 INSTALLATION INSTRUCTIONS LAMINATED PLASTIC TOILET PARTITIONS 1540 Classic
More informationBaby Grande with Crank, Housing, and Side Rails Installation Instructions
Baby Grande with Crank, Housing, and Side Rails Installation Instructions Tools Needed Hardware Provided (per shade) Hardware Needed Drill 3/8 Metal Drill Bit ¼ Masonry Drill Bit Measuring Tape Pencil
More informationAssembly Instructions
RoomScape Furniture System March 2013 - Bed Styles bed deck board bed deck board top cap top cap base glide middle side rail frame frame stacking device frame middle lower reinforcement side rail Single
More informationOn the Right Track. Installation Guide
On the Right Track Installation Guide Table of Contents General Introduction Introduction...1 Local Building Codes...1 Tools Required...1 Additional Assistance...1 Parts Glossary Components...2 Track...5
More informationThe Cambridge Raised Planter Extension Kit
ASSEMBLY INSTRUCTIONS The Cambridge Raised Planter Extension Kit www.newenglandarbors.com www.newenglandarbors.co.uk in (0 cm) 8 in ( cm). in (90 cm). in (8 cm). in (8 cm) 8. in ( cm) 9 in ( cm) Please
More informationInstalling DoorSense August Smart Lock Pro
Installing DoorSense August Smart Lock Pro First, decide how you would like to install the DoorSense. August provides two options for installation: a surface mount and a flush mount installation. The surface
More informationAssembly and Installation Guide
The Easy Hang Closet Solution SM Install Your elfa In An Instant. Enjoy The Benefits For A Lifetime. Basic Tools For elfa Assembly and Installation Level Hand or Power Drill Drill Bits 1/8", 3/8", 5/16"
More informationwoodworkersjournal.com MATERIAL LIST
MATERIAL LIST T x W x L 1 Legs (2) 1 1 2" x 3 1 2" x 36 7 16" 2 End Uprights (2) 1 1 2" x 3 1 2" x 32 1 2" 3 Stringers (4) 1 1 2" x 3 1 2" x 42" 4 Top Cladding, Long (2) 3/4" x 7 1 4" x 65 3 4" 5 Side
More informationOceanside Outdoor Vinyl Shower Kit (3 x 3 Enclosure)
Oceanside Outdoor Vinyl Shower Kit ( x Enclosure) A B ASSEMBLY GUIDE REQUIRED FOR INSTALLATION (A) Zippity Post Extension for In-Ground Installation (Sold as 4-Packs) (B) Zippity Galvanized Steel Surface
More informationGlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationThe Festival Assembly Instructions
The Festival Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown CONTACT INFORMATION: HomePlace Structures 301 Commerce Drive New
More informationUNIVERSAL PANEL AND GATE
PVC Fencing / Residential Style UNIVERSAL PANEL AND GATE INSTALLATION INSTRUCTIONS Fencing Without Boundaries TM 1 BEFORE YOU START, IT S IMPORTANT TO CHECK......That fence footings do not exceed legally
More informationQwik-Fence Installation Instructions
Qwik-Fence Installation Instructions 1 Tools Required The following installation instructions should be used as a guide for installing Folding Guard Qwik-Fence Partitions. Good common sense and appropriate
More informationContour Hanger ASSEMBLY INSTRUCTIONS
Contour Hanger ASSEMBLY INSTRUCTIONS CONTOUR HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket
More informationStainless Steel 95C34 Series
Stainless Steel 95C34 Series Toilet Partition Installation Manual PHONE: FAX: 866-317-2786 ATTENTION DO NOT MIX FASTENER PACKS EACH FASTENER PACK HAS THE NECESSARY BOLTS, BARRELS AND SCREWS TO INSTALL
More informationROCKWELL. Two Panel Door. Half X Door. Double X Door. Z Combination Door
ROCKWELL 4 in 1 DOOR Choose between four door styles with this Door Kit. Our versatile Rockwell Door Kit is very easy to assemble. All materials and hardware needed to assemble any of the four styles are
More informationOWNER S MANUAL Table Tennis Table Patent Pending
OWNER S MANUAL Table Tennis Table Patent Pending Be sure to write your model number and serial number here for future reference. You can find these numbers printed on the bottom of the table. MODEL # T8266
More informationStep by Step Installation Instructions. Poly Shutters. Customer Service or visit us online at smithandnoble.com
Step by Step Installation Instructions Poly Shutters Customer Service 800.248.8888 or visit us online at smithandnoble.com Thank you for purchasing from smith+noble. Your new window treatments have been
More informationMount to the Wall INSTALLATION MANUAL
Mount to the Wall 15 Locate the Wooden Studs This step applies to wooden stud wall installation only. Determine and mark the exact locations of two stud centers on the wall. Wooden studs should be spaced
More informationInstallation Instructions
Important 1. Install product in environmentally controlled conditions. 2. Acclimate materials 24 hrs before installation. Maintain temperature controlled environment after installation. 3. Installers should
More informationGambrel Barn Construction Manual 8x8 through 16x24 Units
Gambrel Barn Construction Manual 8x8 through 16x24 Units Tools Needed: Cordless drill (12V or higher) #2 square drive bit Hammer 6 step ladder Tape measure Square utility knife w/ blade & hook blade Little
More informationStep by Step Installation Instructions. Poly Shutters. Customer Service or visit us online at smithandnoble.com
Step by Step Installation Instructions Poly Shutters Customer Service 800.248.8888 or visit us online at smithandnoble.com THANK YOU for purchasing from smith+noble. Your new window treatments have been
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Low Profile Tilt Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com
More informationALUMINUM RAILING INSTALLATION INSTRUCTIONS. 1) Check Contents Of Packages: Verify that all parts have arrived and that they match the packing list.
ALUMINUM RAILING INSTALLATION INSTRUCTIONS AF#2010-308A Glass Infill Systems 1) Check Contents Of Packages: Verify that all parts have arrived and that they match the packing list. 2) Gather and Identify
More informationFortress Al HOME posts must always be secured to the deck framing. Fortress Al HOME posts should never be attached to only the deck boards.
Installation Instructions for Fortress Al HOME Traditional Adjustable Panels with Simplified and Al HOME Posts It is the responsibility of the installer to meet all code and safety requirements, and to
More information*** All chrome surfaces should be cleaned using a clean damp cloth. *** No abrasive cleaning agents or materials should be used.
Cleaning *** All chrome surfaces should be cleaned using a clean damp cloth. *** No abrasive cleaning agents or materials should be used. *** No chemical cleaners can be used on the glass use only mild
More informationLocker Pedestal Installation Instructions
Locker Pedestal Installation Instructions LK-PED-INST-0314r1 Parts List Single Pedestal Back to Back Pedestal Horizontal Support Tube TS-169 Post Flange TS-190 Post Cap Fasteners Provided: #8 x ¾ round
More informationIMPORTANT!!! ASSEMBLY ASSEMBLY INSTRUCTIONS. (Internal Dimensions)
ASSEMBLY ASSEMBLY INSTRUCTIONS (Internal Dimensions) Ent Spec Edition Ltr v-0- Overall dimensions including base: 7. L x 9 W x 0 H cms 97.5" L x 7" W x 8.7" H IMPORTANT!!! Please read these instructions
More informationMcCue Bumper Installation Instructions
McCue Bumper Installation Instructions McCue 8" Bumper Tools Required: Saw with 10-12" blade Tape measure Flat head screwdriver Phillips screw driver Pencil or chalk line Drill with Philips driver bit
More informationInsolroll Clutch Operated Shades Installation Instructions Installation Instructions
All clutch operated shades are shipped fully assembled and ready for installation. Mounting screws are not provided. Screws for chain guide installation to meet the child safety standards are provided.
More informationInstallation Instructions CR3/G2 BioBlend -3 Wood Chair Rail - Stock Length
Important 1. Install product in environmentally controlled conditions. 2. Acclimate materials 24 hrs before installation. Maintain temperature controlled environment after installation. 3. Installers should
More informationFLEX SHOWER DOOR INSTALLATION INSTRUCTIONS
FLEX SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals
More information